Konica 7065 GUIDE MANUAL 7065ev4

7065

INSTRUCTION MANUAL

7065

INSTRUCTION MANUAL

Before copying, read this guide.

Keep in the right hand rear pocket of the machine.

Thank you very much for your purchase of the Konica 7065.
This Manual deals with making copies, correct handling of the machine, and
precautions for safety. Please read before copying.
In order to maintain a satisfactory copying performance, please keep this
Manual readily available for reference in the right hand rear pocket of the
machine.

E

NERGY STAR® Program

E

NERGY STAR Program has been established

The
to encourage the widespread and voluntary use of
energy-efficient technologies that reduce energy
consumption and prevent pollution. As an

S

TAR Partner, Konica Corporation, Inc. has

determined that this product meets the

S

TAR guidelines for energy efficiency grounding it on

the following features.

E

NERGY

E

NERGY

Auto Low Power

This function conserves energy by lowering the set temperature of the fixing
unit. In the standard setting, Auto Low Power operates automatically when 15
minutes have elapsed after completion of the last copy, with the copier remaining
in the ready to copy state during that time.
The time period for the Auto Low Power function can be set for 5 minutes, 10
minutes, 15 minutes, 30 minutes, 60 minutes, 90 minutes, 120 minutes, or 240
minutes. See p. 5-2 for details.

Automatic Shut-Off

This function achieves further energy conservation by partially turning OFF the
power supply, thereby reducing energy consumption to 20W or less. In the
standard setting, Automatic Shut-Off follows Auto Low Power, operating
automatically when 90 minutes have elapsed after completion of the last copy,
with the copier remaining in the ready to copy state during that time.
The time period for the Automatic Shut-Off function can be set for 30 minutes,
60 minutes, 90 minutes, 120 minutes or 240 minutes. See p. 5-3 for details.

Automatic Duplex Copying

To reduce paper consumption, use this function to make double-sided (duplex)
copies, automatically.

We recommend that you utilize the Auto Low Power function, the Automatic
Shut-Off function, and the Automatic Duplex Copying function.

Section 1: Introduction

Features of the Konica 7065

Copier Features

Standard Equipment

Optional Equipment

Introduction

1

Section 1 : Introduction

Features of the Konica 7065

• AE - Automatic Exposure
Automatically adjust exposure to compensate for the original.

• Alternate Exit
When no Finisher is installed, alternately switch the horizontal and vertical orientation of
each sorted set as it outputs to the exit tray. Be sure to load both A4/B5 and A4R/B5R in
separate trays other than the Multi-sheet bypass tray.

• AMS - Automatic Magnification Selection
Automatically select an appropriate magnification ratio when Paper Size is selected
manually. In the case of the Direct Selection Screen, automatically select it when [-A-] key
is touched.

• APS - Automatic Paper Selection
Automatically select copy paper size to match the original documents.

• ATS - Automatic Tray Switching
Automatically switch tray to allow copying to be continued without interruption when the
selected tray becomes empty while copying is in progress.

• Auto Layout
The original image on the platen glass is copied and centred on a sheet.

• Auto Low Power
Automatically lower the power after a specified period of copier inactivity.

• Auto Reset
Automatically reset to auto mode defaults after a specified period of copier inactivity.

• Auto Shut-Off
Automatically shut off the main power after a specified period of copier inactivity.

• Booklet
Create A5 or A4 booklets from A4 size originals in 1-2 or 2-2 copy mode.

• Chapter
Start chapter pages on the right side (front pages) of the finished document. Only duplex
mode (1-2 or 2-2) is compatible.

• Combination
Copy a fixed number (2, 4, or 8) of pages onto one sheet of copy paper.

• Copy Density
Manually select up to 9 density levels.

• Copy Mode
Select the desired simplex mode (1-1 or 2-1); or duplex mode (1-2 or 2-2).

1 - 2

Section 1 : Introduction

Features of the Konica 7065 (continued)

• Data Printing
Print the following three types of data for confirmation; copy quantity for each password,
copy limit for each password, copy quantity for each paper size.

• Density Shift
Adjust density levels of the four density modes (Auto, Text, Photo, Increase Contrast) into
two levels to lighter and three levels to darker.

• Dual Page
Copy both pages of an open book or book-size sheet separately onto two A4 sheets in 1­1 mode or separately onto each side of one A4 sheet in 1-2 mode. You can use the Dual
Page mode with the Front or Front/Back cover mode. The cover page(s) will be scanned
and copied normally before image division is performed on the other pages.

• Frame/Fold Erasure
Erase border and/or fold image area using Frame (1 - 15mm), Fold (1 - 30mm), or Frame
& Fold.

• Image Insert
Store pages in memory from the platen glass, and insert the pages into a document
copied from the document feeder.

Introduction

1

• Image Rotation
Before copying, rotate the original image when its portrait/landscape orientation is different
from the copy paper orientation.

• Image Shift
Create or remove a binding margin (shift amount from -99 ~ 250mm in 1mm increments);
reduce image to prevent image loss (reduce & shift amount from 1 ~ 250mm in 1mm
increments).

• Interrupt Copying
Interrupt copying in progress to perform copying from the platen glass or document feeder.

• Job Memory
Program up to 15 jobs and Recall each job by job number or name, as needed. All
compatible platen glass functions can be programmed into Job Memory directly after they
are selected.

• Lens Mode (Preset, Zoom)
Select Preset ratios, three reduction and three enlargement ratios.
Zoom ratios can be selected from 33% ~ 400% in 1% increments.

• Machine Status Confirmation
Display the current machine status on LCD for confirmation.

• Magnification
Set user-programmable ratios under User Set 1, User Set 2 and User Set 3.

1 - 3

Section 1 : Introduction

Features of the Konica 7065 (continued)

• Manual Shut-off/Low power
Shut off or Low power the main power when pressing [POWER SAVER ON/OFF] key.

• Mixed Original
Copy mixed size originals from the document feeder in APS or AMS mode. APS
automatically selects the copy size of each original. AMS mode allows you to select one
paper size for all originals.

• Non Image Area Erase
When copying from the platen glass when the document cover is open, copy only the
image area and not the exposed area of glass, which would otherwise copy as black.

• Non STD Size
Identifies the special original size which the 7065 could not detect in order to select the
optimal paper size for copying or printing.

• OHP Interleave
Copy onto transparency film and interleave blank or copied paper for each original copied.

• Output for Machine with FS-106 Finisher Installed:
Non-Sort, Sort, Staple-Sort, and Group modes using the primary (main) tray
Non-Sort Face Down exit, Non-Sort Face Up exit, Group Face Down exit, and
Group Face Up exit modes using the secondary (sub) tray

Select an output tray and output mode on the Output Mode Screen and on the Control
panel. For details of each output mode, see Section 7: Output Modes.

• Output for Machine with FS-108BM Finisher Installed:
Non-Sort, Sort, Staple-Sort, and Group modes using the primary (main) tray
Non-Sort Face Down exit, Non-Sort Face Up exit, Group Face Down exit, and
Group Face Up exit modes using the secondary (sub) tray
Stapling & Folding, and Folding modes using the booklet tray

Select an output tray and output mode on the Output Mode Screen and on the Control
panel. For details of each output mode, see Section 7: Output Modes.

• Output for Machine with no Finisher Installed: Sort and Group modes

Use the default condition to output copies in the same order as the originals. Use the Sort
mode to alternately switch the horizontal and vertical orientation of each copied set upon
exit. Use the Group mode to output multiple copies of each original without offsetting them
upon exit.

• Output for FS-108BM Finisher with PI-108 Cover Sheet Feeder Installed:
Cover Sheet mode
Manual Staple mode

For details of each output mode, see Section 7: Output Modes.

• Overlay

Copy multi-originals so that each includes a common image overlay, previously scanned.

1 - 4

Section 1 : Introduction

Features of the Konica 7065 (continued)

• Paper Capacity

Total 3600 sheets, including two 500-sheet trays, a 1,500-sheet tray, a 1,000-sheet tray,
and a 100-sheet Multi Sheet Bypass tray.

• Platen Memory

Scan documents into memory from the platen glass and/or the document feeder and
insert the pages into another document copied from the document feeder. If an incompatible
function is selected in this mode, the latter function will not be selected, and a Caution
message will be displayed.

• Power Saver

Automatically turns off all but nominal power supply after a specified period of copier
inactivity, for optimal efficiency. Power is returned after a brief warm up period by pressing
[POWER SAVER ON/OFF] key on the Control panel.

• Program Job

Scan documents into memory while designating different tray for each original, then print
all the images collectively. Use this function when copies require several paper types.

Introduction

1

• Proof Copy

To ensure correct output before running multiple copies, run a proof copy by touching
PROOF COPY on the Check Screen or pressing [PROOF COPY] key on the Control
panel.

• Repeat Image

Select the horizontal image area across the page, and repeat it down the page as many
times as the repeat width setting (10 ~ 300mm) permits in manual or auto.

• Reserve

Scan in subsequent copy jobs while the 7065 is busy printing or copying.

• Resolution (High, Very High)

High resolution mode and Very High resolution mode provide optimal image quality for
photos and complicated graphics and text which contain a large amount of detail.

• Reverse Image

Reverse the image from black-on-white to white-on-black or vice versa.

• Sheet/Cover Insertion

Insert up to 15 blank or copied sheets from Tray 1, Tray 3, or the Multi-Sheet Bypass Tray,
or insert blank or copied front and back covers from Tray 1, Tray 3 or the Multi-Sheet
Bypass Tray.

• Staple

Select the stapling position and number of staples.

• Text/Photo Enhance

Enhance photo image in Photo mode; enhance text image in Text mode; enhance lighter
image in increase contrast mode.

1 - 5

Section 1 : Introduction

Features of the Konica 7065 (continued)

• Thin/Thick Paper

2

Use Thin mode when copy paper weight is less than 60g/m

2

paper weight is over 90g/m

.

; use Thick mode when copy

• Userset Density (USERSET 1, USERSET 2)

Output up to 16 density samples on a total of 4 pages that display 4 samples per page,
then program the desired density under USERSET 1 and/or USERSET 2.

• Weekly Timer

Can be set according to the needs of each work environment. Turn main body power Off/
On daily or weekly, during lunch time, on holidays, and also enable the timer-interrupt
mode, which allows temporary use of the machine even when the machine is in the daily,
weekly, or holiday Off mode.

• Z-Folded Original

This feature set the RADF to accept the Z-folded originals.

1 - 6

Section 1 : Introduction

Copier Features

Standard Equipment

Main Body with 4 Paper Trays (500/500/1,000/1,500 sheets)
Reversing Automatic Document Feeder (RADF) (DF-312)
Automatic Duplex Unit (ADU)
Configuration Options:

with Multi-Sheet Bypass Tray (100 sheets)

Optional Equipment

Stapler Finisher (FS-106)

This finisher is equipped with two exit trays.
Secondary (sub) tray: Four output types can be specified on the Output Mode Screen.

(1) Non-sort and face down exit
(2) Non-sort and face up exit
(3) Group and face down exit
(4) Group and face up exit

Primary (main) tray: Four output types can be specified by [
keys on the Control panel and by the setting on the Output Mode Screen. Face up exit
is not available.

(1) Non-sort exit
(2) Sort exit
(3) Staple sort exit
(4) Group exit

STAPLE SORT] and [SORT]

Introduction

1

Stapler Finisher (FS-108BM)

This finisher is equipped with three exit trays and a cover sheet feeder (option).
Secondary (sub) tray: Four output types can be specified on the Output Mode Screen.

(1) Non-sort and face down exit
(2) Non-sort and face up exit
(3) Group and face down exit
(4) Group and face up exit

Primary (main) tray: Four output types can be specified by [
keys on the Control panel and by the setting on the Output Mode Screen. Face up exit
is not available.

(1) Non-sort exit
(2) Sort exit
(3) Staple sort exit
(4) Group exit

Booklet tray: Stapled and folded, or simply folded booklets are to be delivered onto this
tray. These two finishing modes can be specified on the Output Mode Screen.

Cover Sheet Feeder (PI-108)

Used when selecting COVER SHEET on the Output Mode Screen, or when stapling
copies manually.

Large Capacity Tray (LT-352) (3,500 sheets)
Expanded Memory Unit-32MB
Video Interface Kit

STAPLE SORT] and [SORT]

Tandem Kit 7065

1 - 7

Section 2 : Safety Information

Caution Labels and Indicator

Danger, Warning and Caution Symbols

Requirements for Safe Use

Power Source

Environment

Precautions for Routine Handling

Safety

2

Information

Section 2 : Safety Information

Caution Labels and Indicator

The caution labels and indicator are attached to the machine areas, as shown below,
where you are advised to pay special attention to avoid any dangerous situations or
serious injury.

CAUTION

If you touch any place which you are advised by any caution label or caution indicator to
keep yourself away from, you may be burned or injured. Do not remove caution labels or
indicators. If any caution label or caution indicator is soiled, please clean to make legible.
If you cannot make them legible, or if the caution label or indicator is damaged, please
contact your service centre.

CAUTION

High temperature!

Do not touch. Use
care when
clearing paper.

CAUTION

This internal area is
very hot. To avoid
getting burned DO
NOT TOUCH.

CAUTION

High temperature!

Do not touch. Use care when
clearing paper.

WARNING

This area generates high
voltage. To avoid an
electrical shock DO NOT
TOUCH.

CAUTION

This internal area is
very hot. To avoid
getting burned DO
NOT TOUCH.

2 - 2

CAUTION

The ADU guide plate is not latched
when raised. Do not release it,
otherwise the ADU guide plate will
slam shut and may cause injury.

Section 2 : Safety Information

Use care after opening the paper exit
outlet. DO NOT put your hand into it;
otherwise you may be injured.

CAUTIONCAUTION

Use care after opening the
paper exit outlet.
DO NOT put your hand into it;
otherwise you may be injured.

Safety

2

Information

FS-108BM Finisher

CAUTION

Inside the lower paper exit
outlet is the roller drive unit.
DO NOT put your hand into it;
otherwise you may be injured.

FS-106 Finisher

2 - 3

Section 2 : Safety Information

Danger, War ning and Caution Symbols

The following indicators are used on the caution labels or in this manual to categorize the
level of safety cautions.

DANGER:

Action highly liable to cause a death or serious injury.

WARNING:

Action liable to cause a death or serious injury.

CAUTION:

Action liable to cause light injury, medium trouble or physical damage.

If you find any of these indicators when removing jammed paper, adding toner, or reading
the manual, be sure to follow the information.

If the safety cautions in the manual become illegible due to soilage, etc., please buy a new
copy from your service centre.

2 - 4

Section 2 : Safety Information

Requirements for Safe Use

To ensure your safe use of the machine, the following describes the precautions you are
required to observe without fail for the power source of the machine and during installation
and routine handling. Be sure to read and observe them.

Power Source

CAUTION: Plug Socket

• A plug socket is limited in capacity. Use only a power source with the correct rating for

the machine; otherwise, hazardous situations such as smoking or igniting may occur.
See the following list to match the power supply and power consumption:
a) 230V/50Hz: More than 10A
b) 110V/60Hz: More than 15A
c) 230V/60Hz: More than 10A
d) 127V/60Hz: More than 15A

• Avoid multiple connections in the same outlet. Do not use multiple outlet adaptors.

CAUTION: Power Plug and Lead

Safety

2

Information

• Be sure to insert the power plug firmly into the power socket. Otherwise an accident

may occur as a result of smoking or igniting. If the inserted power plug is loose in the
socket, even after it has been positively inserted, disconnect the plug and contact your
electrical contractor.

• For plug cable equipment, that the socket-outlet shall be installed near the equipment

and shall be easily accessible.

• Do not bend or crush the power lead. If your copier power lead is bent or damaged in

any way, contact your Service Centre immediately. Do not attempt to repair it yourself,
and do not continue to operate the copier. A damaged power lead may result in
overheating, a short circuit, or fire.

• Do not bundle or coil the power lead of the copier. Otherwise an accident may occur

as a result of overheating or fire.

CAUTION: Connecting Multiple Loads to One Socket Outlet Prohibited

Never connect multiple loads to one socket outlet using a multi-outlet extension lead or
branched socket. Otherwise an accident may occur as a result of overheating or fire.

CAUTION: Extension Lead

An extension lead is limited in capacity. Unless the lead has adequate capacity, smoking
and/or igniting may occur, and an accident may be caused from overheating. Should
smoking and/or igniting occur, contact your electrical contractor immediately. If you require
further information about power requirements, power consumption, extension leads,
adapters and connectors, please contact your Konica service centre, and also consult
your electrical contractor.
When using an extension lead with a reel, let out the full length from the reel. Using the
lead in rolled-up condition may result in overheating, smoking and/or igniting.

2 - 5

Section 2 : Safety Information

Requirements for Safe Use (continued)

Power Source (continued)

WARNING: Earth wire (Taiwan and the Philippines Only)

• Be sure to attach the earth wire to the machine and connect it to the ground correctly;

otherwise, a leak may occur to electrically shock the operator during machine operation.
The earth wire is supplied as an accessory to the machine.

• The earth wire connected to any inadequate place may cause explosion or electric

shock.
Do not connect the earth wire to any of the following:
(1) Gas pipe
(2) Lightening conductor
(3) Earth wire for telephone
(4) Resin water pipe, or any water pipe or tap not allowed to be connected to the earth

wire by Waterworks Office
If you have any questions on connecting the earth wire, please consult your service
centre.

2 - 6

Requirements for Safe Use (continued)

Environment

CAUTION: Prevention of Fire

Do not install near flammable materials, curtains and
volatile combustibles, that can catch or cause fire.

CAUTION: Prevention of Short Circuit

Do not install the copier where it could be splashed
with rain water, or water from a tap, to avoid a short
circuit.

CAUTION: Temperature and Humidity

• Keep away from direct sunlight, heat sources such
as stoves, cool air from an air conditioner and hot
air from a heater.

• Avoid any environment that is outside the range
shown below:

10 to 30°C in temperature
10 to 80% in humidity.

Section 2 : Safety Information

Safety

2

Information

CAUTION: Ventilation

• Maintain the installation place well-ventilated.

• Keep away from dust or corrosive gases. These materials may cause poor image
quality.

• During the use of machine, the machine generates ozone but in an insufficient amount
to cause any hazard to the human body.
However, if the machine is used in a poorly ventilated room, many copies are made,
or plural copiers are used at the same time, an odour may be detected. Ensure adequate
ventilation for a comfortable working environment.

CAUTION: Vibration

Do not install on a floor which is subject to vibration or is not level.

2 - 7

Section 2 : Safety Information

Requirements for Safe Use (continued)

Environment (continued)

CAUTION: Installation Space

Allow sufficient space for facilitating copy operation, changing parts, and periodic inspection.
Especially leave an adequate space behind the machine to let hot air out from the rear
fan.

(Unit: mm)

200

450

1606

756

400

500

1164

1664

800

710

1710

Konica 7065

500

*

464362

756

315

210

1664

1164

800

710

200

1897

2107

525

*: The dimention required when withdrawing the Large Capacity Tray (LT-352)

Konica 7065 + FS-106 Finisher + LT-352

2 - 8

1710

Requirements for Safe Use (continued)

Environment (continued)

Section 2 : Safety Information

Safety

2

Information

500

210

40

*: The dimention required when withdrawing the Large Capacity Tray (LT-352)

544322

1977

2187

756

315

Konica 7065 + FS-108BM Finisher + LT-352

*

1664

1164

525

800

710

1710

Please Be Reminded!

Finisher primary (main) tray of FS-106/FS-108BM Finisher gradually goes down while printed
material is output. DO NOT allow any object to interfere with the operation of the tray on the left
side of the finisher, as any interference may cause damage to the finisher.

200

2 - 9

Section 2 : Safety Information

Requirements for Safe Use (continued)

Precautions for Routine Handling

WARNING: High Voltage

DO NOT TOUCH the high voltage parts indicated with WARNING label or described in
the manual.

CAUTION: Actions in Response to Troubles

• If the Service Call screen is displayed and copier operations cannot be continued any
more, stop the operation to prevent any unexpected accident. Write down the report
code as stated on 2 line of the message, then switch off the copier and disconnect from
the power socket. Contact your service centre and inform them of the report code.

• Do not touch the high temperature parts indicated with CAUTION labels or described
in the manual.

• Do not touch the inside of the machine for any other purpose than removing jammed
paper or adding toner.

• If machine repair is necessary, be sure to contact your service centre. Never attempt
to repair it by yourself.

• If any abnormal sound, smell or smoke comes from the machine, immediately stop
using it, turn off the power switch, disconnect the power plug and contact your service
centre.

• If the breaker trips or the fuse blows, turn off the power switch, reset the breaker or the
fuse, and turn on the machine. If the same situation occurs again, contact your service
centre.

• Insure the replacement fuse conforms with the rating of the power source. Never use
a fuse with an incorrect rating.

CAUTION: Prevention of Fire

Do not use volatile combustibles such as a thinner or alcohol near the machine.

CAUTION: Prohibition of Machine Modification

Do not modify or remove any parts by yourself.

2 - 10

Section 2 : Safety Information

Requirements for Safe Use (continued)

Precautions for Routine Handling (continued)

CAUTION: Prevention of Machine Troubles

• Do not drop small metallic objects such as paper clips or
staples inside the machine.

• Do not place any heavy or hard objects such as a vase,
books or ornaments on the machine.

CAUTION: Recommendation of Periodic Check

Be sure to check periodically the following points:
(1) The main lead or the power plug does not generate abnormal heat.
(2) The power plug is not inserted loosely or the lead is not cut or scratched.
(3) The earth wire is correctly connected.
(4) The power plug or the power outlet is not covered with dust.
If you find anything abnormal in the above items, stop using the machine and contact your
service centre.

CAUTION: Toner

Safety

2

Information

• Keep the toner cartridge away from children. The toner is nontoxic; however if you
inhale or contact with eyes by accident, flush with water and seek medical advice.

• Do not throw the empty toner cartridge into a fire. If it is thrown into a fire the toner may
ignite and cause a dangerous situation.

CAUTION: FS-106 Finisher Paper Capacity

The capacity of the FS-106 Finisher exit tray is listed below. When the total number of
copies in the copy run exceeds the stated capacity, be sure to unload the exit tray whilst
the copier is still copying. Failure to do so will cause the copier to jam. The following
capacity is for 80g/m
of different sizes.

Primary (Main) Tray: Non-Sort/Sort/Group Mode

500 sheets max. (A5*
2,000 sheets max. (A4, A4R, B5, B5R, 8.5"x11", 8.5"x11"R)
1,500 sheets max. (A3, B4)

*1: Load A5 in landscape orientation ( ) only.

2

: Load B6 in landscape orientation ( ) only using Non-sort mode (unavailable when using Sort/

*

Group mode).

Primary (Main) Tray: Staple-Sort Mode

1,000 sheets max. (A3, B4, A4, A4R, B5, 8.5"x11", 8.5"x11"R)
(The maximum number of sheets varies depending on the number of originals, copied
paper size and a stapled position. See p. 4-7.)

2

paper. The limit will decrease when loading the exit tray with copies

1

, B6*2)

Secondary (Sub) Tray: Non-Sort Mode

200 sheets max. (A3, B4, A4, A4R, B5, B5R, A5*, B6*, 8.5"x11", 8.5"x11"R)

* : Load A5 and B6 in landscape orientation ( ) only.

2 - 11

Section 2 : Safety Information

Requirements for Safe Use (continued)

Precautions for Routine Handling (continued)

CAUTION: FS-108BM Finisher Paper Capacity

The capacity of the FS-108BM Finisher exit tray is listed below. When the total number of
copies in the copy run exceeds the stated capacity, be sure to unload the exit tray whilst
the copier is still copying. Failure to do so will cause the copier to jam. The following
capacity is for 80g/m
of different sizes.

2

paper. The limit will decrease when loading the exit tray with copies

Primary (Main) Tray: Non-Sort/Sort/Group Mode

500 sheets max. (A5*

1

, B6*2)
3,000 sheets max. (A4, A4R, B5, B5R, 8.5"x11", 8.5"x11"R)
1,500 sheets max. (A3, B4)

*1: Load A5 in landscape orientation ( ) only.
*2: Load B6 in landscape orientation ( ) only in Non-sort mode (unavailable in Sort/Group mode).

Primary (Main) Tray: Staple-Sort Mode

1,000 sheets max. (A3, B4, A4, A4R, B5, 8.5"x11", 8.5"x11"R)
(The maximum number of sheets varies depending on the number of originals, copied
paper size and a stapled position. See p. 4-8.)

Secondary (Sub) Tray: Non-Sort Mode

200 sheets max. (A3, B4, A4, A4R, B5, B5R, A5*, B6*, 8.5"x11", 8.5"x11"R)

* : Load A5 and B6 in landscape orientation ( ) only.

Booklet Tray

100 sheets max. (A3, B4, A4R, 8.5"x11"R)
(The maximum number of sheets varies depending on pages of a booklet and selecting
either the Folding or the Stapling & Folding. See p. 4-9.)

CAUTION: Inside Booklet Mode Outlet

Inside the Booklet mode outlet is the roller drive unit. DO NOT put your hand into it, when
removing the folded or stapled & folded sheet; otherwise you may be injured.

CAUTION: Finisher Paper Exit Outlet

To avoid injury when stapling large size copies, DO NOT put your hand into the open
Paper Exit Outlet.

CAUTION: Paper Capacity for the Exit Tray

The exit tray capacity is 100 sheets. If a copy run of more than 100 is required, be sure
to remove the copies from the exit tray before the maximum capacity is reached. Failure
to do so will cause the copier to jam.

2 - 12

Section 2 : Safety Information

Requirements for Safe Use (continued)

Precautions for Routine Handling (continued)

CAUTION: Power Saver and Weekly Timer

• During Power Saver mode the copier is still connected to the mains power supply and
power is still applied to certain areas of the machine. To avoid any unexpected troubles
turn the power OFF when not using the copier for long periods of time.

• When the Weekly Timer indicator is lit, turning power OFF will disable weekly timer
function.

CAUTION: Fixing Unit

The Fixing unit is internally very hot. To avoid getting burned, DO NOT TOUCH. Be
careful when withdrawing the fixing unit.

WARNING: Drum Unit

The drum unit has a high voltage generated.
To avoid an electrical shock, DO NOT TOUCH.

Safety

2

Information

CAUTION: ADU Guide Plate

The ADU guide plate is not latched when raised. Do not release it, otherwise the ADU
guide plate will slam shut and may cause injury.

CAUTION: Dispose of a Disused Copying Machine

Do not dispose of this copier yourself. Contact your service centre, who can arrange for
its safe disposal.

If you change the place of installation, please contact your service centre.

2 - 13

Section 3: Machine Information

Machine Configuration

External Machine Call-Outs

Internal Machine Call-Outs

Standard/Optional Equipment

Control Panel Layout

Touch Screen

Full-Automatic Mode Screen

Basic Screen (Layer Selection Screen)

Basic Screen (Direct Selection Screen)

Initial Settings

Auto/Reset Mode

Automatic Paper Selection (APS)

Automatic Magnification Selection (AMS)

Machine

3

Information

Machine

Configuration

Control Panel/
Touch Screen

Automatic

Settings

Service

Settings

Automatic Exposure (AE)

Automatic Tray Switching (ATS)

Lead Edge Delete

Service Settings

Finisher-Paper Capacity

Key Operator Password

EKC Master Key Code

Weekly Timer Master Key Code

Weekly Timer Key in Help Screen

Control Panel Contrast Key in Help Screen

Staple Sheet Capacity

Notice Message: ADD TONER/ PM CALL/ APPLICATION/INTERRUPT

Basic Screen Selection

Section 3 : Machine Information

Machine Configuration

External Machine

!8Power switch

!7Finisher FS-108BM

(option)

!6Left side cover

(not shown)

!5Front door

!4Tray 1

(Universal tray)

!3Tray 2

!9LCD touch screen

!2ADU

!1Tray 4

@0Control panel

!0Tray 3

qRADF

oLower right side

cover (not shown)

wWork table

eMulti-sheet

bypass tray

rKey counter (option)

tUpper right side cover

yLCT door

uTray 5: Large

capacity tray
LT-352(option)

iPaper level indicator

Internal Machine

uTotal counter

yFixing unit

tLever 2

3 - 2

qToner box

wDrum unit

eKnob 3

rLever 1

Section 3 : Machine Information

Machine Configuration (continued)

External Machine Call-outs

q RADF (Reversing Automatic Document Feeder) automatically feeds multiple

originals one at a time to the platen glass for copying.

w Work table provides a convenient workspace for documents both before and after

copying.

e Multi-sheet bypass tray used for small quantity copying onto plain paper or special

paper.

r Key counter (option) manages the number of copies made on the machine.
t Upper right side cover opens to allow removal of mishandled paper.
y LCT door opens to allow loading paper.
u Tray 5: Large capacity tray LT-352 (option) is initially fixed at A4 and holds 3,500

sheets.

i Paper level indicator indicates the approximate number of sheets remaining in the

LCT.

o Lower right side cover opens to allow removal of mishandled paper.
!0 Tray 3 is fixed at A4 and holds 1,000 sheets.

It can be reset by service to size B5 or 8.5"x11".

!1 Tray 4 is initially fixed at A4 and holds 1,500 sheets.

It can be reset by service to size A4R, B5, B5R, 8.5"x11" or 8.5"x11"R.

!2 ADU is used for stackless duplex copying.
!3 Tray 2 is initially fixed at A3 and holds 500 sheets.

It can be reset by service to size A3, B4, F4, A4R, A4, B5R, B5, A5*, 11"x17", 8.5"x14",

8.5"x11"R or 8.5"x11".

!4 Tray 1 (universal tray) is user adjustable and holds 500 sheets of either A3/B4/F4 /

A4R/A4/B5R/B5/A5* or B6*

!5 Front door opens to the internal copier to allow clearing of mishandled paper and

replenishing of toner.

!6 Left side cover opens to allow removal of mishandled paper.
!7 Finisher FS-108BM (option) sorts, staple-sorts, and groups copies into finished sets.
!8 Power switch turns copier power On/Off when pressed.
!99 LCD touch screen displays interactive operation screens.
@0 Control panel controls copier operations.

Machine

3

Information

Machine

Configuration

NOTE:

*: A5 or B6 paper is available in landscape orientation ( ) only.

Internal Machine Call-outs

q Toner box holds the toner supply.
w Drum unit forms the copy image.
e Knob 3 can be turned to ease removal of mishandled paper.
r Lever 1 can be moved to ease removal of mishandled paper.
t Lever 2 can be moved to ease removal of mishandled paper from the fixing unit.
y Fixing unit fuses the toner onto the copy paper.
u Total counter indicates the total number of copies made.

3 - 3

Section 3 : Machine Information

Machine Configuration (continued)

Standard/Optional Equipment

FS-108BM Finisher
(see details below)

Tray 1 (500 sheets)
Tray 2 (500 sheets)
Automatic Duplex Unit - ADU
Tray 3 (1,000 sheets)
Tray 4 (1,500 sheets)

FS-106 Finisher details

Primary (main) tray:

holds ejected paper as sorted sets.
Select Sort mode to output offset­sorted sets; Staple mode to output
stapled sets; Group mode to output
offset-grouped sets.

Reversing Automatic Document Feeder - RADF (DF-312)

Work Table

Multi-Sheet Bypass Tray (100 sheets)

Tray 5: Large Capacity Tray
(LT-352) (3,500 sheets)
(see details below)

Secondary (sub) tray:

holds ejected paper in the
following four modes designated
on the Output Mode screen:

q Non-sort Face Down exit
w Non-sort Face Up exit
e Group Face Down exit
r Group Face Up exit

Finisher door:

opens to change
the staple cartridge
and to remove
mishandled paper.

Large Capacity Tray details

LCT upper door:

opens to load paper.

Paper level indicator:

indicates the approximate
number of sheets.

Large Capacity
Tray (LT-352)

FS-106 Finisher

Cover sheet feeder (option):

sets the cover sheet when
selecting Cover Sheet on
Output Mode Screen, or
sets a copied set in
manual stapling.

Primary (main) tray:

holds ejected paper as sorted sets.
Select Sort mode to output off set­sorted sets; Staple sort mode to
output stapled sets; Group mode to
output offset-grouped sets.

3 - 4

FS-108BM Finisher details

Booklet tray

FS-108BM Finisher

Secondary (sub) tray:

holds ejected paper in the
following four modes designated
on the Output Mode screen:

q Non-sort Face Down exit
w Non-sort Face Up exit
e Group Face Down exit
r Group Face Up exit

Manual stapling
control panel

Finisher door

Booklet mode outlet:

ejects finished copied sets
when selecting Folding mode
or Stapling & Folding mode.

Control Panel Layout

Section 3 : Machine Information

r

t

SPECIAL ORIGINAL

APPLICATION

ROTATION OFF

u

y

STORE

i

o

!2

!0

COPY

PRINTER

TANDEM

CHECK

JOB MEMORY

AUTO RESET

!3 !4

HELP

!1

!5

PRINT QUANTITY

@1

!6

RECALL

@2

CLEAR QTY.

@3

!7

INTERRUPT

PROOF COPY

START PRINT

!9

!8

STOP / CLEAR

@4 @5

@0

TIMER

POWER SAVER

ON / OFF

w

q

OUTPUT

STAPLE SORT

SORT

e

q OUTPUT displays a screen for selecting an output condition.
w STAPLE SORT selects Staple-sort mode.
e SORT selects Sort mode.
r LCD TOUCH SCREEN displays machine and copying status; help information;

interactive screens; and touch keys for selecting all functions.

t APPLICATION displays a menu for selecting special application functions.
y SPECIAL ORIGINAL displays a screen for selecting conditions to scan originals.
u ROTATION OFF selects/deselects the image rotation function.
i STORE stores platen/RADF originals into memory, then copies the whole set.
o MODE INDICATOR lights when copy/printer/tandem mode is set.
!0 MODE switches copy, printer, and tandem mode.
!1 HELP displays a screen with help for the currently selected function.
!2 CHECK displays a screen showing all settings that are selected for the current job.
!3 AUTO RESET restores copier to automatic mode settings or to key operator settings.
!4 JOB MEMORY displays screens for selecting job store/job recall functions.
!5 KEYPAD enters numeric values.
!6 PRINT QUANTITY indicator displays the current print quantity setting.
!7 PROOF COPY outputs a single set of copies to confirm whether the current settings

are selected properly.

!8 INTERRUPT stops copying in progress to allow copying from the platen glass.
!9 POWER SAVER ON/OFF activates power-saving mode for times when the copier

is inactive, or activates timer interrupt mode when weekly timer function is active.

@0 TIMER lights when the timer function is set.
@1 [P] accesses programming modes for setting special functions.
@2 [0] RECALL recalls the print quantity of the current job.
@3 CLEAR QTY. allows resetting of print quantity.
@4 START PRINT activates copying.
@5 STOP/CLEAR stops the copying sequence; deletes the stored memory.

Machine

Machine

3

3

Information

Information

Machine

Configuration

Control Panel/
Touch Screen

3 - 5

Section 3 : Machine Information

Touch Screen

The touch screen is an LCD that displays interactive screens with touch sensitive keys for
making copy job selections. Selections are highlighted at the touch. The screens also
work with the conventional control panel keys.

CAUTION:

The touch screen of the control panel is covered with glass. Do not drop heavy items on
the glass, or put excess weight or pressure on it; otherwise the glass may break or become
scratched.

After the power switch is turned on, the Konica name displays for approximately 10 seconds,
until initial machine settings are established. Then, the Warm-Up Screen displays for
approximately 6.5 minutes, until the fixing temperature is reached.

When the Basic Screen (or Full-Automatic Mode screen) is displayed, the touch screen
becomes interactive. The interactive condition enables you to communicate directly with
the copier system simply by touching keys displayed on the screen; or by pressing
conventional keys, as required. In addition, the screens automatically display information
regarding machine and copying status. Additional help is available any time with the [HELP]
key, which can be pressed from any screen, except from Job Memory or Key Operator
Mode Screens.

Full-Automatic Mode Screen

The Full-Automatic mode displays after warm-up. As shown in Initial setting on p. 3-8,
Full-Automatic settings include Print Quantity 1; Copy Mode 1s1; Lens Mode 1:1; RADF
on; AE, APS on; Finisher off.
Except for Print Quantity, all Full-Automatic Mode settings can be changed by the key
operator in the Initial Setting Menu Screen. In this case, the Basic Screen displays after
warm-up instead of the Full-Automatic Mode Screen.
The following modes can be accessed from this screen: Copy Mode, Copy Density, Lens
Mode, Paper Size.

Full-Automatic Mode Screen

3 - 6

Section 3 : Machine Information

Touch Screen (continued)

Basic Screen (Layer Selection Screen)

The 7065 Layer Selection Screen is the default basic screen. To switch the default basic
screen to the Direct Selection Screen, contact your service representative.
The Basic Screen includes a two-line message bar at the top; a user-interactive portion
in the centre; and mode keys at the bottom for selecting Copy Mode, Copy Density, Lens
Mode and Paper Size. This screen enables you to use touch keys on the screen as well
as conventional keys to select modes, function, settings, paper trays, etc. After warm-up,
copying conditions may be set in the Initial Setting Menu of the Key Operator Mode.

Basic Screen

Machine

3

Information

Control Panel/
Touch Screen

Basic Screen (Direct Selection Screen)

While the Layer Selection Screen displays subsequent screens when each mode key is
pressed, the Direct Selection Screen displays only one screen that shows the mode options
and also registers the selections you make. The Direct Selection Screen does not display
the Full-Automatic Mode Screen.

Basic Screen (Direct Selection Screen)

3 - 7

Section 3 : Machine Information

Initial Settings

Initial settings represent the initial condition when power is turned on; when EKC password
is set; or when Auto/Reset mode is restored, either manually or automatically.

Print Quantity; 1
Magnification Ratio: 1:1 (key operator setting)
RADF: ON (key operator setting)
Copy mode: 1-1 mode (key operator setting)
AE: (Automatic Exposure) : ON (key operator setting)
APS: (Automatic Paper Selection): ON (key operator setting)
Finisher: Non-sort on Primary (main) tray (key operator setting)

Auto/Reset Mode

The Auto/Reset function can be set for OFF/ 30 seconds/ 1 minute/ 1.5 minutes/ 2 minutes/

2.5 minutes/ 3 minutes/ 3.5 minutes/ 4 minutes/ 4.5 minutes/ 5 minutes by the key operator.

Initially, the mode is set to function after 1 minute of copier inactivity. The Auto/Reset key
function also re-displays the Basic Screen, unless these settings are changed by the key
operator in the Initial Setting Menu Screen. See p. 12-42 to p. 12-46.

Automatic Paper Selection (APS)

When APS is highlighted on the touch screen, the appropriate copy paper size is
automatically selected. When copying from the platen glass or document feeder, APS
detects the sizes indicated below. For key operator settings of APS, see p. 12-42 to p. 12-

46.

❒ PLATEN GLASS: A3, B4, F4, A4R, A4, B5R, B5, A5R (B6R or 5.5"x8.5")
❒ RADF: A3, B4, F4, A4R, A4, B5R, B5, A5R, A5, 8.5"x11"

Automatic Magnification Selection (AMS)

AMS functions automatically when Copy Size is pressed in the Full-Auto mode. An
appropriate ratio is selected, based on the relationship of copy size to original size.

Automatic Exposure (AE)

When AE is highlighted on the touch screen, the appropriate exposure level is automatically
selected to match the copy density of the original. Manual density adjustments override
AE.

Automatic Tray Switching (ATS)

When the selected paper tray becomes empty while copying is in progress, automatic tray
switching detects the same copy paper size loaded in another tray to allow copying to be
continued without interruption. The Multi-sheet bypass tray is not included in tray switching.
Automatic Tray Switching is switched on by using the key operator mode.

3 - 8

Section 3 : Machine Information

Lead Edge Delete

When using the RADF, image deletion of a few millimeters will occur on the lead edge for
the purpose of controlling copy quality and copy reliability, unless deactivated by the key
operator. See p. 12-42 to p. 12-46.

Service Settings

The following functions can be provided by your Konica service representative, who is
authorized to change DIP switch settings. Contact your service centre if setting change is
required.

Finisher-Paper Capacity

In the default condition, the 7065 will produce unlimited sets. If required, service can set
the copier to stop copying when the number of copies exceeds specified capacity.

Key Operator Password

Service can set a 4-digit Key operator password to access the Key Operator Mode Screen.
After this setting, a Password Entry Screen will display and require entry of the Key operator
password to access the Key Operator Mode Screen.

Machine

Machine

3

3

Information

Information

Automatic

Settings

Service

Settings

EKC Master Key Code

Service can set an 8-digit EKC master key code to access the EKC Setting Menu Screen.
After this setting, the EKC Master Key Code Screen will be displayed and will always
require entry of the set EKC master key code to access the EKC Setting Menu Screen.

Weekly Timer Master Key Code

Service can set a 4-digit Weekly timer master key code to access the Weekly Timer
Setting Menu Screen. After this setting, the Weekly Timer Master Key Code Screen will
be displayed and will always require entry of the set Weekly timer master key code to
access the Weekly Timer Setting Menu Screen.

Weekly Timer Key in Help Screen

Service can set the copier with weekly timer system to display the Weekly timer key on the
Help Screen to check and see the contents of Weekly timer settings.

Control Panel Contrast Key in Help Screen

Service can set the copier to display Control panel contrast key on the Help Screen to
display the Contrast Adjustment Screen for adjusting panel contrast.

3 - 9

Section 3 : Machine Information

Service Settings (continued)

Staple Sheet Capacity

Staple capacity is changeable, and may be set to 45, 40, or 35 by service.

Notice Message: ADD TONER/ PM CALL/ APPLICATION/INTERRUPT

Service can set the copier to display “ADD TONER” indicator when the toner supply is
low, “PM CALL” when preventive maintenance is required, “APPLICATION” when
Application function is selected, or “INTERRUPT” when Interrupt function is set in the
message area of the screen.

Basic Screen Selection

The 7065 Basic Screen defaults to the Layer Selection Screen type. If you wish to make
your Basic Screen default to the Direct Selection Screen, contact your service centre.

3 - 10

Section 4: Paper Information

Positioning Originals on the Platen Glass

Positioning an Original for Manual Copying

Using the Reversing Automatic Document Feeder (RADF)

Positioning Originals

Positioning Mixed Originals

Paper in Main Body Trays

Paper in Large Capacity Tray (LT-352) (Option)

Paper in Multi-Sheet Bypass Tray

Paper in Automatic Duplex Unit

Paper in FS-106 Finisher (Option)

FS-106 Finisher Primary (Main) Tray

FS-106 Finisher Secondary (Sub) Tray

Paper

4

Information

Paper in FS-108BM Finisher (Option)

FS-108BM Finisher Primary (Main) Tray

FS-108BM Finisher Secondary (Sub) Tray

FS-108BM Finisher Booklet Tray

Paper in Cover Sheet Feeder (PI-108) (Option)

Cover Sheet Feeder

Paper Weight Compatibility Chart

Section 4 : Paper Information

Positioning Originals on the Platen Glass

Positioning an Original for Manual Copying

Use the platen glass when originals are not suitable for use with the document feeder,
e.g., when size is incompatible, or when originals are folded, stapled, torn, or in generally
poor condition.

Specifications

❒ All capacities are stated for 80g/m2 paper
❒ Max. original size: A3, sheet or book
❒ Max. book weight/thickness: 6.8kg/30mm
❒ Original placement: Face down on right depth side of glass

Procedure

1 Raise the document cover, as shown in the illustration above.
2 Place original FACE DOWN in the right rear corner, aligning the edge with the right

measuring guide.

3 Gently close the document cover, to prevent the original from shifting on the glass.

CAUTION:

When the finisher/paper exit tray capacity is exceeded due to the print quantity selected,
remove the copied sets while the paper is exiting; otherwise mishandled paper will occur.

TIP:

To eliminate black copy marks on edges when copying from a book without selecting Dual Page
mode, select Frame/Fold Erasure or Non-image Area Erase in Application mode.

4 - 2

Section 4 : Paper Information

Using the Reversing Automatic Document Feeder (RADF)

Specifications

❒ All capacities are stated for 80g/m2 paper
❒ Max. RADF tray capacity: 50 sheets
❒ Max. original exit tray capacity: 50 sheets
❒ Original size range: A3, B4, F4, A4R, A4, B5R, B5, A5*1, 8.5"x11"
❒ Original placement: Face up; orientation same as copy paper
❒ Orientation (portrait-landscape): Same as copy paper feeding direction
❒ Original weight: 50~130g/m2 (no special stock)
❒ Curling tolerance/stack height: 10mm or less/20mm or less

ADF MODE 1-1, 1-2

Original size: A3, B4, F4, A4R, A4, B5R, B5, A5*1, 8.5"x11"
Max. feeder capacity: 50 original sheets

Paper

4

Information

RADF MODE 2-2, 2-1

1

Original size: A3, B4, F4, A4R, A4, B5R, B5, A5*

, 8.5"x11"

Max. feeder capacity: 50 original sheets

NOTE:

*1: A5 is available in both landscape ( ) and portrait ( ) orientation.

MIXED SIZE ORIGINAL MODE

Original size: A3, B4, A4R, A4, B5, A5*2 mixed,

2

B4, A4R, B5R, B5, A5*

2

A4R, B5R, A5*
B5R, A5*

NOTE:

*2: A5 original is available in portrait ( ) orientation only.

3

: A5 original is available in landscape ( ) orientation only.

*

3

mixed, or

mixed

mixed,

Mixed feeder capacity: 50 original sheets

Unsuitable RADF Originals

12

Curled, creased of
folded originals

Paste-ups or
cut-outs

3

Books

4

Glossy or transparent
originals, OHP film,
art paper, cellophane

5

Doubled, punched or
stapled originals

6

Thin or thick originals

4 - 3

Section 4 : Paper Information

Using the Reversing Automatic Document Feeder (RADF) (continued)

Positioning Originals

The document feeder (RADF) automatically feeds up to 50 originals directly to the platen
glass, starting with the top sheet. The RADF should only be used for unstapled, unfolded,
smooth, flat originals.

Specifications

❒ Original size detection requires accurate paper guide adjustment.
❒ APS detects size A3, B4, F4, A4R, A4, B5R, B5, A5*, 8.5"x11"
❒ Size, weight, and capacity are specified for all copy modes on p. 4-3.

NOTE:

*: A5 is available in both landscape ( ) and portrait ( ) orientation.

Procedure

Before placing originals in the tray, be sure the document feeder is closed fully.

1 Position original(s) FACE UP on the document feeder tray.

Place two-sided originals with page one FACE UP.

2 Adjust paper guides.

4 - 4

Section 4 : Paper Information

Using the Reversing Automatic Document Feeder (RADF) (continued)

Positioning Mixed Originals

Mixed size originals can be copied together from the document feeder in either APS mode
or AMS mode. In APS mode, copies will be output on mixed paper sizes to match the
originals. In AMS mode, copies will be output on one common paper size that you select
in which case an appropriate AMS magnification ratio will be selected automatically. To
use the mixed original mode, see procedure on p. 8-10 to p. 8-12.

Specifications

❒ Mixed original size: A3, B4, A4R, A4, B5, A5*1 mixed,

B4, A4R, B5R, B5, A5*1 mixed,
A4R, B5R, A5*
B5R, A5*

NOTE:

*1: A5 original is available in portrait ( ) orientation only.
*2: A5 original is available in landscape ( ) orientation only.

❒ RADF capacity: Max. 50 sheets
❒ Print quantity: Max. 9,999 sheets
❒ Incompatible Basic Copying Conditions: Alternate exit, Reserve with APS, Folding/

Stapling & Folding in APS, Cover sheet with APS

❒ Incompatible Original Scanning Conditions: Resolution (Very high), Non STD size
❒ Incompatible Applications: Sheet/Cover insertion, Chapter, Combination, Booklet, OHP

interleave, Image insert, Dual page, Program job, Non-image area erase, Repeat, Frame/
Fold erasure, AUTO layout, Thin/Thick paper, Image shift, Overlay

2

mixed

1

mixed, or

Paper

4

Information

Align originals to the back left corner.

Procedure

Before using the Mixed Original mode, be sure the document feeder is closed completely.

1 Arrange originals in order, and place them as described below:

Place A3/B4 originals face up or side 1 up in the document feeder, in landscape
orientation, i.e., with short edge feeding.
Position A4 and B5 sizes in either portrait or landscape orientation.
Position A5 size in landscape orientation except only mixed B5R size original.

2 Position mixed originals FACE UP, aligned with the left rear side of the RADF tray.
3 Adjust the original guide to originals.

4 - 5

Section 4 : Paper Information

Paper in Main Body Trays

Paper Weight: 60~90g/m

2

Total Paper Capacity: 3,600 sheets, including 100-sheet Multi-Sheet Bypass Tray

Tray 1: 500 sheets 80g/m2/ user-adjustable to any standard size from A3, B4, F4, A4R,

A4, B5R, B5, A5*, B6*

Tray 2: 500 sheets 80g/m2 / fixed to A3, B4, F4, A4R, A4, B5R, B5, A5*, 11"x17", 8.5"x14",

8.5"x11"R, or 8.5"x11" (service adjustable)
Tray 3: 1,000 sheets 80g/m2/ fixed to A4, B5, or 8.5"x11" (service adjustable)
Tray 4: 1,500 sheets 80g/m2/ fixed to A4R, A4, B5R, B5, 8.5"x11"R, or 8.5"x11" (service

adjustable)

NOTE:

*: A5 or B6 paper is available in landscape orientation ( ) only.

Paper in Large Capacity Tray (LT-352) (Option)

Paper Weight: 60~90g/m
Total Paper Capacity: 7,100 sheets, including four Main body trays and 100-sheet Multi­Sheet Bypass Tray

Tray 5 (LCT): 3,500 sheets 80g/m2 / fixed to A4 or 8.5"x11"(service adjustable)

2

Paper in Multi-Sheet Bypass Tray

Paper Size: Adjustable from A3~B6*
Paper Weight: 50~170g/m
Multi-Sheet Bypass Tray Capacity: 100 sheets 80g/m

NOTE:

*: A5 or B6 paper is available in landscape orientation ( ) only.

2

; Special (OHP transparent film, labels, hole punch, rag content)

2

stacked: single feed special stock

Paper in Automatic Duplex Unit

Paper Size: A3, B4, A4R, A4, B5R, B5, A5*
Paper Weight: 60~90g/m
Duplex Tray Capacity: Unlimited stackless duplex tray

NOTE:

*: A5 paper is available in landscape orientation ( ) only.

NOTE:

Reliability and copy quality are not guaranteed for all Special papers. Use only paper that is
recommended by Konica.

2

4 - 6

Section 4 : Paper Information

Paper in FS-106 Finisher (Option)

FS-106 Finisher accepts A3, B4, F4, A4R, A4, B5R, B5, A5, B6, 8.5"x11"R, and 8.5"x11"
paper sizes. The finisher tray capacities classified according to paper size in each output
mode are described below.

CAUTION:

When the finisher capacity is exceeded due to the print quantity selected, remove the
copied sets while the paper is exiting; otherwise mishandled paper will occur.

FS-106 Finisher Primary (Main) Tray

FS-106 Finisher (capacities at 80g/m2, unless otherwise indicated)

Non-sort/Sort/Group mode:

500 sheets A5*1, B6*
2,000 sheets A4R, A4, B5R, B5, 8.5"x11"R, 8.5"x11"
1,500 sheets A3, B4, F4

Staple-sort mode:

1,000 sheets*3 A3, B4, F4, A4R, A4, B5, 8.5"x11"R, 8.5"x11"

NOTE:

*1: A5 paper is available in landscape ( ) orientation only.

2

: B6 paper is available in landscape ( ) orientation in Non-sort mode only.

*
*3: Variable according to the number of pages to be stapled. See the table below.

Paper Capacity for Staple-sort mode of Finisher FS-106

No. of pages

(for the same size only)

2 staples

2

A3

1 staple

B4, F4, A4R, A4, B5,

8.5"x11"R, 8.5"x11"

2 staples

1 staple

Paper

4

Information

50
30
25
20

50 sets

50
30
25
20

100 sets

50
30
25
20

100 sets

50
30
25
20

2~9
10~20
21~30
31~40
41~50

Service can set the copier to stop copying when the number of copies
exceeds above capacity. Contact your service centre.

50 sets

FS-106 Finisher Secondary (Sub) Tray

FS-106 Finisher (capacities at 80g/m2, unless otherwise indicated)

200 sheets A3, B4, F4, A4R, A4, B5R, B5, A5*, B6*, 8.5"x11"R, 8.5"x11"

NOTE:

* : A5 or B6 paper is available in landscape ( ) orientation only.

4 - 7

Section 4 : Paper Information

Paper in FS-108BM Finisher (Option)

FS-108BM Finisher accepts A3, B4, F4, A4R, A4, B5R, B5, A5, B6, 8.5"x11"R, and 8.5"x11"
paper sizes. The finisher tray capacities classified according to paper size in each output
mode are described below.

CAUTION:

When the finisher capacity is exceeded due to the print quantity selected, remove the
copied sets while the paper is exiting; otherwise mishandled paper will occur.

FS-108BM Finisher Primary (Main) Tray

FS-108BM Finisher (capacities at 80g/m2, unless otherwise indicated)

Non-sort/Sort/Group mode:

500 sheets A5*1, B6*
3,000 sheets A4R, A4, B5R, B5, 8.5"x11"R, 8.5"x11"
1,500 sheets A3, B4, F4

Staple-sort mode:

1,000 sheets*3 A3, B4, F4, A4R, A4, B5, 8.5"x11"R, 8.5"x11"

NOTE:

*1: A5 paper is available in landscape orientation ( ) only.

2

: B6 paper is available in landscape orientation ( ) in Non-sort mode only.

*
*3: Variable according to the number of pages to be stapled. See the table below.

2

Paper Capacity for Staple-sort mode of Finisher FS-108BM

No. of pages

2~9
10~20
21~30
31~40
41~50

Service can set the copier to stop copying when the number of copies
exceeds above capacity. Contact your service centre.

(for the same size only)

A3

2 staples

50 sets

1 staple

50 sets
50
30
25
20

50
30
25
20

B4, F4, A4R, A4, B5,

8.5"x11"R, 8.5"x11"

2 staples

100 sets

1 staple

100 sets
50
30
25
20

50
30
25
20

FS-108BM Finisher Secondary (Sub) Tray

FS-108BM Finisher (capacities at 80g/m2, unless otherwise indicated)

200 sheets A3, B4, F4, A4R, A4, B5R, B5, A5*, B6*, 8.5"x11"R, 8.5"x11"

NOTE:

* : A5 or B6 paper is available in landscape orientation ( ) only.

4 - 8

Section 4 : Paper Information

Paper in FS-108BM Finisher (Option) (continued)

FS-108BM Finisher Booklet Tray

Folding mode:

Paper Size : A3, B4, A4R, 8.5"x11"R
Paper Weight : 60~90g/m2 paper (80g/m2 paper is recommended)
Number of Folded Sheet: 3 sheets max.
Booklet Tray Capacity : Approx. 100 sheets max.

33 sets max. of 3-sheet-folded booklet

(33 x 3 = 99 sheets)

50 sets max. of 2-sheet-folded booklet

(50 x 2 = 100 sheets)

Stapling & Folding mode:

Paper Size : A3, B4, A4R, 8.5"x11"R
Paper Weight : 60~90g/m2 paper (80g/m2 paper is recommended)

one cover paper only (91~200g/m2 paper)

Number of Folded Sheet: 16 sheets max. (using 80g/m2 paper only)

15 sheets max. (using one cover paper)

Booklet Tray Capacity : Approx. 100 sheets max.

20 sets max. of 5-sheet-folded booklet

(20 x 5 = 100 sheets)

10 sets max. of 10-sheet-folded booklet

(10 x 10 = 100 sheets)

6 sets max. of 16-sheet-folded booklet

(6 x 16 = 96 sheets)

Paper

4

Information

CAUTION:

Inside the Booklet mode outlet is the roller drive unit. DO NOT put your hand into it, when
removing the folded or stapled & folded sheet; otherwise you may be injured.

Paper in Cover Sheet Feeder (PI-108) (Option)

Cover Sheet Feeder

Cover Paper Size : A3, B4, F4, A4R, A4, B5, A5*, 8.5"x11"R, 8.5"x11"
Cover Paper weight : 50~200g/m2 paper

NOTE:

* : A5 paper is available to the manual stapling only.

4 - 9

Section 4 : Paper Information

Paper Weight Compatibility Chart

RADF
Main Body Trays
Large Capacity Tray
Multi-Sheet Bypass Tray
ADU
In-Bin Stapler Finsher FS-106
In-Bin Stapler Finsher FS-108BM
Cover Sheet Feeder PI-108

Document Feeder 50 ~ 130g/m
All Trays 60 ~ 90g/m
60 ~ 90g/m
50 ~ 170g/m
60 ~ 90g/m
60 ~ 170g/m
60 ~ 170g/m
50 ~ 200g/m

2

2

2

2

2

2

2

2

NOTE:

Reliability and copy quantity are not guaranteed for all Special papers. Use only paper that is
recommended by Konica.

4 - 10

Section 5: Copier Management

Power Saver Mode

Auto Low Power

Manual Low Power

Auto Shut-Off

Manual Shut-Off

Entering an EKC Password

Weekly Timer Function

Timer Interrupt

Copier

5

Management

Power Saver

EKC

Weekly Timer

Section 5 : Copier Management

Power Saver Mode

There are two modes for the Power saver as described below.
Low power mode enables you to conserve energy by maintaining a lower fixing temperature
during periods of copier inactivity.
Shut-off mode conserves even more energy by partially turning OFF the power supply.

CAUTION

During Power Saver mode the copier is still connected to the mains power supply and
power is still applied to certain areas of machine. To avoid any unexpected troubles turn
the power OFF when not using the copier for long periods of time.

Auto Low Power

This function automatically lowers the power after a specified period of copier inactivity.
The Auto low power function can be set to 5 minutes/ 10 minutes/ 15 minutes/ 30 minutes/
60 minutes/ 90 minutes/ 120 minutes/ 240 minutes. Initially, the mode is set to function
after 15 minutes of copier inactivity. For the key operator setting, see p. 12-48 to p. 12-49.
When Auto low power is on, the following message will be displayed on the dimmed Basic
screen.

Basic Screen

POWER SAVER ON/OFF] LED remains dark.

The [

Release Auto Low Power

Press any key on the control panel other than [

OFF]. The Auto low power will be released and the LCD screen recovers usual brightness.

START PRINT] and [POWER SAVER ON/

5 - 2

Section 5 : Copier Management

Power Saver Mode (Continued)

Manual Low Power

Press [POWER SAVER ON/OFF]. The Low Power Setting Screen will be displayed. Touch

YES to activate the Low power mode.

Low Power Setting Screen

NOTE:

The Manual low power setting can be selected by Key operator. For the key operator setting, see
p. 12-42 to p. 12-46. When selecting the Manual low power setting, the Manual shut-off setting is
released.

Copier

5

Management

Power Saver

When Manual low power is on, the following message will be displayed on the dimmed
Basic screen.

Basic Screen

The [POWER SAVER ON/OFF] LED remains dark.

Release Manual Low Power

Press any key on the control panel other than [

OFF]. The Auto low power will be released and the LCD screen recovers usual brightness.

START PRINT] and [POWER SAVER ON/

5 - 3

Section 5 : Copier Management

Power Saver Mode (continued)

Auto Shut-Off

This function automatically shuts off the main power after a specified period of copier
inactivity.
The Auto shut-off can be set for 30 minutes/ 60 minutes/ 90 minutes/ 120 minutes/ 240
minutes. Initially, Auto shut-off is set to function after 90 minutes of copier inactivity. For
the key operator setting, see p. 12-48 to p. 12-49.

Release Auto Shut-Off

Press [

Manual Shut-Off

Press [POWER SAVER ON/OFF]. The Shut-Off Setting Screen will be displayed. Touch

YES to activate the Manual shut-off mode.

POWER SAVER ON/OFF]. The copying operation will be available.

Shut-Off Setting Screen

NOTE:

The Manual shut-off setting can be selected by Key operator. For the key operator setting, see p.
12-42 to p. 12-46. When selecting the Manual shut-off setting, the Manual low power setting is
released.

The [POWER SAVER ON/OFF] LED will light and all other LEDs and the LCD screen will
be turned off.

Release Manual Shut-Off

Press [

SAVER ON/OFF] LED turned off and the LCD screen displayed.

POWER SAVER ON/OFF]. The Manual shut-off will be released, with the [POWER

5 - 4

Section 5 : Copier Management

Entering an EKC Password

An EKC password is required only when the Electronic Key Counter (EKC) feature is
activated; a User Password is assigned; and “Enter E.K.C. password” is displayed on the
touch screen.

Basic Screen

Procedure

1 Enter your 5-digit EKC password, using the keypad.

If the EKC password is invalid, the copier will reset to the Initial mode.
In that case, enter the correct password; or contact the key operator.

2 Press [

sec.

START PRINT] once to display your current copy count and copy limit for 3

Copier

Copier

5

5

Management

Management

Power Saver

EKC

Current count / limit

018888/025000

Ready to copy

When your copy count reaches the copy limit, the following message is displayed:

Copy limit reached

025001/025000

In that case, contact the key operator to reset your copy limit.

3 Make copying selections, and enter print quantity, as required.
4 When all settings are acceptable, press [

START PRINT].

5 - 5

Section 5 : Copier Management

Q

T

Q

Weekly Timer Function

When a copier is under control of the weekly timer function,
the TIMER indicator on the right side of the control panel is lit.
Important: When the TIMER indicator is lit, the copier will

INTERRUPT

automatically be turned off. Do not turn it off by pressing power
switch.

PROOF COPY

STOP / CLEAR

START PRINT

TY.

Timer Interrupt

When the TIMER indicator light is on and other indicators are off, copying is unavailable
due to the weekly timer function.

However, copying is available by following procedure.

Procedure

1 Press the [POWER SAVER ON/OFF].

The Basic screen will be displayed along with the
messages shown below.

Please wait
Copier is warming up

Timer interrupt mode
Enter password

INTERRUPT

PROOF COPY

STOP / CLEAR

START PRINT

TY.

TIMER

POWER SAVER

ON / OFF

TIMER

POWER SAVER

ON / OFF

NOTE:

The timer interrupt password is not factory set and must be entered
by the key operator (see p. 12-41 in “Section 12: Key Operator
Mode”). In the event the timer interrupt password has not been
entered by the key operator, the message shown in Step 3 will
display instead.

2 Enter a 4-digit number timer interrupt password using

the keypad on the control panel.
If an invalid password is entered, continue by entering

PRINT QUANTITY

INTERRUPT

the valid 4-digit password.

Timer interrupt mode

PROOF COPY

3 Press the [

Enter password ✻✻✻✻

START PRINT].

RECALL

CLEAR QTY.

START PRINT

S

Input copy time
0 hour(s) 05 minute(s)

5 - 6

Weekly Timer Function (continued)

T

T

Q

Timer Interrupt (continued)

4 Enter a 1-digit hour (ex. 3 hour is 3) using the keypad on

the control panel. (0 ~ 9)

5 Press the [

START PRINT].

Section 5 : Copier Management

PRINT QUANTITY

INTERRUPT

Input copy time
3 hour(s) 05 minute(s)

6 Enter a 2-digit minutes (ex. 7 minutes is 07) using the

keypad on the control panel. (05 ~ 59)

Input copy time
3 hour(s) 07 minute(s)

7 Press the [

START PRINT].

Copying is available until the set time is up.

Position original in
the RADF

8 When timer interrupt of the copier is finished, press the

POWER SAVER ON/OFF].

[

RECALL

PRINT QUANTITY

RECALL

INTERRUPT

PROOF COPY

CLEAR QTY.

CLEAR QTY.

PROOF COPY

START PRINT

INTERRUPT

PROOF COPY

START PRINT

TIMER

POWER SAVER

ON / OFF

S

S

Copier

5

Management

Weekly Timer

STOP / CLEAR

START PRINT

TY.

9 The Shut-Off Setting Screen will be displayed. Touch

YES. The copier returns to the

OFF state and copying is disabled.

5 - 7

Section 6: Basic Operations

How to Make a Basic Copy

The Full-Automatic Mode

The Basic Screen

Copy Mode

Copy Density

Automatic Exposure (AE)

Manual Mode (Lighter, Normal, Darker)

Userset Density (USERSET 1, USERSET 2)

Density Shift

Lens Mode

Automatic Paper Selection (APS)

Automatic Magnification Selection (AMS)

Preset and User Set Ratios

Zoom Mode

Vertical/Horizontal Zoom

6

Operation

Basic Copy

Basic

Paper Size

Reserve

Set Reserve Job

Troubleshooting in Reserve Setting

Status

Memory Copy

Platen Memory Copy

RADF Memory Copy

Output Mode for Machine without Finisher

Rotation

Rotation and APS

Rotation and AMS

To Release Automatic Rotation

Check Mode and Proof Copy

Interrupt Mode

Copy Mode

Copy Density

Lens Mode

Paper Size

Reserve/

Status

Memory Copy

Output without

Finisher

Rotation

Check Mode &

Proof Copy

Interrupt Mode

Help Mode

Multi-sheet

Bypass Tray

Help Mode

Using the Multi-Sheet Bypass Tray

Section 6 : Basic Operations

How to Make a Basic Copy

The Full-Automatic Mode

The Full-Automatic Mode Screen displays only if the setting was made in the Initial Setting
Screen of the Key Operator mode (see p. 12-8). The screen displays Full-Automatic setting
when power is turned on; when Auto Power Saver mode is activated; when EKC password
is set; or when Auto/Reset mode is manually or automatically restored.

When the Electronic Key Counter (EKC) is activated, a valid 5-digit EKC password, assigned
by the key operator, must be entered before copying can be performed. See p. 5-5.

If a Key Counter is required, the message “Please insert key counter” is displayed. Insert
a Key Counter.

All of the Full-Automatic settings, except Print Quantity, can be changed by the key operator
in the Initial Setting Menu Screen.

Full-Automatic Mode Screen

Messages and Copier Status

Notice message

Folder keys

Status key

Staple/Rotation/
Stapling/Folding icon

Memory indicator

Basic Mode keys

The Basic Screen

When the copying conditions are changed, or the Initial settings are changed in the Key
Operator mode, the Basic Screen will be displayed.

Basic Screen

Messages and Copier Status

Notice message

Folder keys

NOTES:

1 A simple copying job can be selected during warming up. Position originals, then press [START

PRINT]. Copier starts printing after warm-up operation is completed.

2 During the process of successive copying jobs, the message “Warming up” may be displayed

in the message area of the Basic Screen to maintain the copy image quality.

Status key

Staple/Rotation/
Stapling/Folding icon

Memory indicator

Settings Options

Basic Mode keys

6 - 2

How to Make a Basic Copy (continued)

Procedure

1

Set Copying Conditions

1 Close the document feeder securely.
2 Press [
3 As required, set the copying conditions.

STOP/CLEAR] to return to the initial status.

Basic Copy Settings on Basic Screen

Copy mode : see p. 6-5 ~ p. 6-7
Copy density : see p. 6-8 ~ p. 6-12
Lens mode : see p. 6-13 ~ p. 6-18
Paper size : see p. 6-19
Reserve : see p. 6-20 ~ p. 6-23
Status : see p. 6-24 ~ p. 6-25

Other Basic Copying Operations:

Memory copy

Platen memory copy : see p. 6-26 ~ p. 6-27
RADF memory copy : see p. 6-28 ~ p. 6-29

Output mode for machine

without Finisher : see p. 6-30 ~ p. 6-32
Rotation : see p. 6-33 ~ p. 6-35
Check mode and Proof copy : see p. 6-36 ~ p. 6-39
Interrupt mode : see p. 6-40 ~ p. 6-41
Help mode : see p. 6-42
Using the multi-sheet bypass tray

: see p. 6-43 ~ p. 6-44

Section 6 : Basic Operations

6

Operation

Basic Copy

Basic

Output mode Operations:

Section 7 describes how to select output modes.

Original scanning condition Selections:

Section 8 describes how to select original scanning conditions.

Application Selections:

Section 9 describes how to select Application functions.

NOTE:

If the Basic Screen displays ADJUSTMENT MODE in the message area, this means that the
machine was left in the service adjustment mode by a service centre. If this occurs, please contact
your service centre and request that the mode be turned off; otherwise copying may be adversely
affected.

6 - 3

Section 6 : Basic Operations

T

T

How to Make a Basic Copy (continued)

2

Position Originals ...FACE UP in RADF

FACE DOWN on Platen Glass

Position original document FACE UP in the document feeder or FACE DOWN on the
platen glass.

3

Enter Print Quantity

Press the Ten keys to set the desired print quantity.
To change the print quantity, press [
the correct quantity.

CLEAR QTY.] and enter

PRINT QUANTITY

INTERRUPT

4

Start Copying

Press [START PRINT] to start copying .

CAUTION

When the finisher / paper exit tray capacity is exceeded
due to the print quantity selected, remove the copied sets
while the paper is exiting; otherwise, mishandled paper
will occur.

RECALL

PRINT QUANTITY

RECALL

CLEAR QTY.

CLEAR QTY.

PROOF COPY

S

START PRINT

INTERRUPT

PROOF COPY

S

START PRINT

6 - 4

Section 6 : Basic Operations

Copy Mode

The Copy Mode key is used to display a selection screen, from which all copy modes can
be selected: 1s1, 1s2, 2s1, 2s2.

Copy Mode Specifications:

Incompatible functions

1s1: Folding/Stapling & Folding with Booklet, Chapter; Booklet
1s2: OHP interleave; Thick paper in Thin/Thick mode
2s1: Folding/Stapling & Folding with Booklet, Chapter; Booklet; Dual page;

Repeat image; Reverse image; AUTO layout; Non-image area erase

2s2: Repeat image; OHP interleave; Dual page; Reverse image; Thick paper

in Thin/Thick paper; Non-image area erase

RADF capacity

1s1, 1s2, 2s2, 2s1: 50 sheets

RADF original size requirements

A3, B4, F4, A4R, A4, B5R, B5, A5*1, 8.5"x11"

6

6

Operation

Operation

Basic Copy

Basic

Basic

Copy paper weight requirements

60~90g/m

Copy paper size requirements

1s1, 1s2, 2s2, 2s1: A3, B4, F4, A4R, A4, B5R, B5, A5*

Sort mode paper size (machine with FS-106/FS-108BM Finisher)

A3, B4, F4, A4R, A4, B5R, A5*2, 8.5"x11"R, 8.5"x11"

Staple-Sort mode paper size (machine with FS-106/FS-108BM Finisher)

A3, B4, F4, A4R, A4, B5, 8.5"x11"R, 8.5"x11"

Folding or Stapling & Folding mode paper size (machine with FS-108BM
Finisher)

A3, B4, A4R, 8.5"x11"R

Cover Sheet Feeder paper size (FS-108BM Finisher with PI-108 Cover
Sheet Feeder)

A3, B4, F4, A4R, A4, B5, A5*3, 8.5"x11"R, 8.5"x11"

NOTE:

*1: A5 original is available in both landscape ( ) and portrait ( ) orientation.
*
*

2

2

: A5 paper is available in landscape orientation ( ) only.

3

: A5 paper is available to the manual stapling only.

2

Copy Mode

6 - 5

Section 6 : Basic Operations

Copy Mode (continued)

Before selecting the Copy Mode shown on the screen below, read specifications on the
previous page and see Section 4 for information on positioning originals.

2-2 Copying

Double-sided original Duplex copy

7065

7065

7065

7065

7065

7065

7065

7065

7065

Single-sided originals

2-1 Copying

Double-sided original

Procedure

1

Set Copying Conditions

1 Touch COPY MODE to display the Copy Mode Selection Screen.

Available keys:

CANCEL, OK

7065

7065

Duplex copy

7065

7065

Simplex copy

1-2 Copying

7065

7065

7065

7065

7065

Full-Automatic Mode Screen

2 Touch the desired mode key: 1s1, 1s2, 2s1, or 2s2.

To immediately de-select the mode, touch
A copy mode key will appear dimmed if it is incompatible with other selections made.

3 Touch

6 - 6

OK to complete the setting and return to the Basic Screen.

Copy Mode Selection Screen

CANCEL.

Section 6 : Basic Operations

T

T

Copy Mode (continued)

2

Position Originals ... FACE UP in RADF

FACE DOWN on Platen Glass

Position original(s) FACE DOWN on the platen glass or FACE UP in the document
feeder, as required.

3

Enter Print Quantity

Press the Ten keys to set the desired print quantity.
To change the print quantity, press [
the correct quantity.

CLEAR QTY.] and enter

PRINT QUANTITY

INTERRUPT

6

Operation

Copy Mode

Basic

4

Start Copying

When all settings are acceptable, press [START PRINT].

CAUTION

When the finisher / paper exit tray capacity is exceeded
due to the print quantity selected, remove the copied sets
while the paper is exiting; otherwise, mishandled paper
will occur.

To cancel the mode after returning to the Basic Screen,

COPY MODE again, touch key for the desired Copy

touch
mode, then touch

OK.

RECALL

PRINT QUANTITY

RECALL

CLEAR QTY.

CLEAR QTY.

PROOF COPY

S

START PRINT

INTERRUPT

PROOF COPY

S

START PRINT

6 - 7

Section 6 : Basic Operations

Copy Density

Automatic Exposure (AE)

AE operates with the initial settings. It detects the density of the original image and
automatically selects the appropriate exposure for the copy.

Manual Mode (Lighter, Normal, Darker)

Select manual copy density to adjust exposure (density) when originals are too light or too
dark. Manual adjustments can be made in 9 levels simply by touching the desired exposure
level, from lighter, to normal, to darker.

Full-Automatic Mode Screen

Density Selection Screen

6 - 8

Section 6 : Basic Operations

R

E

O

Copy Density (continued)

Userset Density (USERSET 1, USERSET 2)

Output copying samples selected from 16 density levels from LIGHTER to NORMAL,
then select the desired exposure and program it as USERSET 1.
Similarly, output copying samples selected from 16 density levels from NORMAL to
DARKER, then select the desired exposure and program it as USERSET 2.
The programmed copy density can be recalled by touching
the Density Selection Screen.

Procedure

1 Place the original on the platen glass.

USERSET 1 or USERSET 2 on

6

Operation

Basic

2 Touch

COPY DENSITY on the Basic Screen while pressing [P] to display the Userset

Density Setting Screen.

3 To program USERSET 1, proceed with step 4.

To program USERSET 2, touch
To return to the Basic Screen, touch

Control Panel

R

EM

ELP

RY

ET

Full-Automatic Mode Screen

PRINT QUANTITY

RECALL

CLEAR QTY.

INT

PRO

STA

Userset lighter, and proceed with step 5.

CANCEL.

Userset Density Setting Screen

Copy Density

6 - 9

Section 6 : Basic Operations

Copy Density (continued)

Userset Density (USERSET 1, USERSET 2) (continued)

4 To output the sample sheet of USERSET 1, touch No. 1 1~4, No. 2 5~8, No. 3 9~12,

No. 4 13~16, then press [START PRINT].

or
If you do not want to change the Userset darker density level, touch
and proceed to step 5.
To program USERSET 1, select the desired density from the sample sheet and
touch the density No. key (1 to 16), then touch

OK. Proceed with step 6.

Userset lighter

Userset Density Setting Screen (darker)

Userset Density Setting Screen (lighter)

5 To output the sample sheet of USERSET 2, touch No. 1 1~4, No. 2 5~8, No. 3 9~12,

No. 4 13~16, then press [START PRINT].

or
To return to the setting of the Userset darker density level, touch
To return to the Basic Screen, touch

CANCEL.

Userset darker.

To program USERSET 2, select the desired density from the sample sheet and
touch the density No. key (1 to 16), then touch

6 The Basic Screen will be displayed. Touch

OK.

COPY DENSITY on the Basic Screen.

The programmed density No. will be displayed on the USERSET key.

Density Selection Screen

6 - 10

Section 6 : Basic Operations

R

E

O

Copy Density (continued)

Density Shift

Density Shift allows the normal range of density settings to be adjusted more towards
lighter settings, or more towards the darker settings.
It is also possible to set different Density Shifts for each of the density modes (Text/photo,
Text, Photo and Increase Contrast).

Density shift 0

Density shift 1

Density shift 2

Density shift 3 (standard)

Density shift 4

Density shift 5

Procedure

1 Select the density mode.

To select the Text/Photo mode, press [

P] then press [5].

The following message will be displayed.

P - mode : 5
Press START to confirm

To select the Text mode, press [

P] then press [6].

The following message will be displayed.

P - mode : 6
Press START to confirm

To select the Photo mode, press [P] then press [7].
The following message will be displayed.

P - mode : 7
Press START to confirm

Basic

6

Operation

R

EM

ELP

RY

ET

PRINT QUANTITY

RECALL

CLEAR QTY.

Copy Density

INT

PRO

STA

To select the Increase contrast mode, press [
The following message will be displayed.

P - mode : 8
Press START to confirm

P] then press [8].

6 - 11

Section 6 : Basic Operations

T

Copy Density (continued)

Density Shift (continued)

2 Press [START PRINT]. The following message will be

displayed.
In Text/Photo mode (P-mode : 5):

PRINT QUANTITY

INTERRUPT

Density Shift (Text/Photo)

3 (0 ~ 5)

In Text mode (P-mode : 6):

CLEAR QTY.

RECALL

Density Shift (Text)

3 (0 ~ 5)

In Photo mode (P-mode : 7):

Density Shift (Photo)

3 (0 ~ 5)

In Increase contrast mode (P-mode : 8):

Density Shift (Increase contrast)

3 (0 ~ 5)

3 Press any key (from 0 - 5) using the keypad to determine the Density shift.

NOTE:

When 6 or above is entered, 5 is selected.

4 Press [STOP/CLEAR]. Density shift is determined.

INTERRUPT

PROOF COPY

POWER SAVER

PROOF COPY

S

START PRINT

TIMER

ON / OFF

6 - 12

STOP / CLEAR

START PRINT

Section 6 : Basic Operations

Lens Mode

Automatic Paper Selection (APS)

APS detects the size of originals placed on RADF or the platen glass, and automatically
selects and feeds the copy paper of the same size as the original in 1:1 mode or of the
appropriate size when magnification ratio is selected at that time.
If the copy paper of the automatically selected size is not loaded in any tray, no copying
will be made, and the message requesting to load the paper of that size will be displayed.

❒ The sizes of originals which can be detected are: A3, B4, F4, A4R, A4, B5R, B5, A5*
❒ Incompatible: AMS

NOTE:

*: A5 original is available in both landscape ( ) and portrait ( ) orientation. (RADF)

A5 original is available in landscape (

The relation of original size, magnification ratio and copy paper size is listed below.

Paper size

0.33 - 0.42

0.43 - 0.50

0.51 - 0.55

0.56 - 0.57

0.58 - 0.61

0.62 - 0.71

0.72 - 0.78

0.79 - 0.82

0.83 - 0.86

0.87 - 0.90

0.91 - 1.00

1.01 - 1.10

Magnification ratio

1.11 - 1.15

1.16 - 1.22

1.23 - 1.41

1.42 - 1.63

1.64 - 1.73

1.74 - 2.00

2.01 - 4.00

A3 B4 F4 A4R B5RA4 B5 A5R A5
B6

B6

A5

B5R

A4R

B4

A3

A5

B5R

A4R

B4

A3

B6

A5

B5R

A4R

F4
B4

A3

) orientation. (Platen glass)

Original size

B6

B6

B6

A5

A5

A5

B5

B5R

B5R

A4R

A4R

A3

A4R

B4

A3

B4

A3

B6

A5

B5

A4R

A3

B6

A5

B5R

A4R

B4

A3

B6

A5

B5

A4

A3

Paper size

0.33 - 0.42

0.43 - 0.50

0.51 - 0.55

0.56 - 0.57

0.58 - 0.61

0.62 - 0.71

0.72 - 0.78

0.79 - 0.82

0.83 - 0.86

0.87 - 0.90

0.91 - 1.00

1.01 - 1.10

1.11 - 1.15

1.16 - 1.22

1.23 - 1.41

1.42 - 1.63

1.64 - 1.73

1.74 - 2.00

2.01 - 4.00

Magnification ratio

Basic

Basic

6

6

Operation

Operation

Copy Density

Lens Mode

6 - 13

Section 6 : Basic Operations

Lens Mode (continued)

Automatic Magnification Selection (AMS)

AMS functions in the Initial setting when Paper Size is selected manually.

❒ Incompatible: APS, Change magnification, Program job, Dual page, Non-image area

erase, Repeat, AUTO layout, Overlay

An appropriate reduction or enlargement ratio will be selected automatically and applied
to the image on the paper size. AMS automatically calculates and selects the correct ratio.

AMS ratios are shown in the table below.

Original size

A3 B4 F4 A4R B5R A4 B5 A5*
A3
B4
F4
A4R
B5R

Paper size

A4
B5
A5*

1.00 1.15 1.27 1.41 1.63 1.00 1.15 2.00

0.86 1.00 1.10 1.22 1.41 0.86 1.00 1.73

0.71 0.82 1.00 1.00 1.15 0.71 0.82 1.41

0.71 0.82 0.90 1.00 1.15

0.61 0.71 0.79 0.86 1.00

0.50 (0.71) 0.58 (0.82) 0.64 (0.90) 0.71 (1.00) 0.82 (1.15)

0.43 (0.61) 0.50 (0.71) 0.55 (0.79) 0.61 (0.86) 0.71 (1.00)

0.50 0.58 0.64 0.71 0.82 0.50 0.58 1.00

0.71 (1.00) 0.82 (1.15)

0.61 (0.86) 0.71 (1.00)

1.00 1.15

0.86 1.00

1.00 (1.41)

0.86 (1.22)

1.41

1.22

( ) is the magnificaton ratio of the Image rotation.

6 - 14

Section 6 : Basic Operations

Lens Mode (continued)

Preset and User Set Ratios

Use the Preset and User Set ratios to increase or decrease magnification in fixed amounts.
If required, the six initially set Preset ratios shown below can be adjusted in the Key

Operator mode. In addition, three User Set ratios are adjustable by the key operator. All
ratios remain effective until they are replaced.

Specifications for Preset and User Set Ratios

❒ 1:1 mode (no magnification)
❒ 6 Preset ratios: 0.71, 0.82, 0.86, 1.00, 1.55, 1.22 and 1.41
❒ 3 User Set ratios: Programmable by key operator and selected from 0.33~4.00
❒ To copy A4 originals to A4 copy paper, select A4 Paper Size, then select 1.00

magnification.

Procedure

1 Touch LENS MODE to enter the Magnification Selection Screen.

Full-Automatic Mode Screen

Basic Screen

Magnification Selection Screen

6

Operation

Lens Mode

Basic

2 Select the desired magnification. The selected key will be highlighted.
3 Touch

To cancel the setting before returning to the Basic Screen, touch
To cancel the setting after returning to the Basic Screen, touch
select the desired ratio, then touch

4 Position original(s) FACE DOWN on the platen glass or FACE UP in the document

feeder, as required.

5 When all settings are acceptable, press [

OK to complete the setting and return to the Basic Screen.

CANCEL.

LENS MODE again,

OK.

START PRINT].

6 - 15

Section 6 : Basic Operations

Lens Mode (continued)

Zoom Mode

Use the Zoom mode to reduce or enlarge the copied original image in 1% increments.

❒ Zoom range: 0.33~4.00

Procedure

1 Touch LENS MODE to enter the Magnification Selection Screen.
2 Touch

ZOOM to display the Zoom Screen.

Full-Automatic Mode Screen

Zoom Screen

Magnification Selection Screen

Basic Screen

3 Use keypad to enter a 3-digit zoom ratio, or use arrows to scroll to the desired ratio.
4 Touch

To cancel the setting before returning to the Basic Screen, touch
To cancel the setting after returning to the Basic Screen, touch
and touch

OK.

OK to complete the setting and return to the Basic Screen.

CANCEL.

LENS MODE again,

ZOOM to display the Zoom Screen. Select the desired ratio, then touch

5 Position original(s) FACE DOWN on the platen glass or FACE UP in the document

feeder, as required.

6 When all settings are acceptable, press [

START PRINT].

6 - 16

Section 6 : Basic Operations

Length

Width

Lens Mode (continued)

Vertical/Horizontal Zoom

Use the Vertical/Horizontal zoom mode to reduce or enlarge vertical and horizontal
dimensions, independently.

❒ Vertical zoom range: 0.33~4.00
❒ Horizontal zoom range: 0.33~4.00

The figure shown below is the sample image using the Vertical/Horizontal zoom.

6

Operation

Basic

Length: 0.50, Width: 0.50

Length: 1.00, Width: 0.50

Length: 2.00, Width: 0.50

Length: 4.00, Width: 0.50 Length: 4.00, Width: 1.00 Length: 4.00, Width: 2.00 Length: 4.00, Width: 4.00

Length: 0.50, Width: 1.00 Length: 0.50, Width: 2.00 Length: 0.50, Width: 4.00

Width

Length

Length: 1.00, Width: 1.00 Length: 1.00, Width: 2.00 Length: 1.00, Width: 4.00

Length:2.00, Width: 1.00 Length:2.00, Width: 2.00 Length: 2.00, Width: 4.00

Lens Mode

6 - 17

Section 6 : Basic Operations

Lens Mode (continued)

Vertical/Horizontal Zoom (continued)

Procedure

1 Touch LENS MODE to enter the Magnification Selection Screen.
2 Touch

Vert/Horiz Zoom to display the Vertical/Horizontal Zoom Screen.

Full-Automatic Mode Screen

Vertical/Horizontal Zoom Screen

Magnification Selection Screen

Basic Screen

3 Touch the Vertical arrow key to select a vertical ratio.
4 Use keypad to enter a 3-digit vertical zoom ratio, or use arrows to scroll to the desired

ratio.

5 Touch the Horizontal arrow key to select a horizontal ratio.
6 Use keypad to enter a 3-digit horizontal zoom ratio, or use arrows to scroll to the

desired ratio.

7 Touch

To cancel the setting before returning to Basic Screen, touch
To cancel the setting after returning to the Basic Screen, touch
and touch
the desired ratio, then touch

OK to complete the setting and return to the Basic Screen.

CANCEL.

LENS MODE again,

Vert/Horiz Zoom to display the Vertical/Horizontal Zoom Screen. Select

OK.

8 Position original(s) FACE DOWN on the platen glass or FACE UP in the document

feeder, as required.

9 When all settings are acceptable, press [

START PRINT].

6 - 18

Section 6 : Basic Operations

Paper Size

Paper size is used to display the Paper Tray Selection Screen, or reset APS, or select a
specific paper tray. When a specific tray is selected, the paper size may require a ratio
adjustment. When using the RADF with Initial settings, a ratio will be selected automatically.

Tray locations correspond to main body & LCT (trays 1, 2, 3, 4, 5). Paper types, such as

BLUE, RED, BRWN, CHLR, HEAD, GREN, YELL, RECY,

trays by the key operator for information only, but paper types cannot be detected by the
machine.

Paper size Specifications

❒ When a selected tray is empty an out-of paper icon will flash on the Paper Tray Selection,

along with a message to load paper in the empty tray.

❒ When a tray is empty, but not selected or in use, the out-of paper icon will appear, but

will not flash in the message area.

❒ If a tray size is changed by the service centre, the new paper size will be reflected on

the screen, automatically.

❒ Incompatible Basic Copying Conditions with AMS: APS, change magnification
❒ Incompatible Original Scanning Conditions with AMS: None
❒ Incompatible Applications with AMS: Dual page, Program job, Non-image area erase,

Repeat, AUTO layout, Overlay

may be specified on some

6

6

Operation

Operation

Basic

Basic

Procedure

1 Touch PAPER SIZE to display the Paper Tray Selection Screen.

Basic Screen Paper Tray Selection Screen

2 Touch
3 When the desired selection is highlighted, touch

To cancel the setting before returning to the Basic Screen, touch
To cancel the setting after returning to the Basic Screen, touch
select the desired paper tray, then touch

4 Position original(s) FACE DOWN on the platen glass or FACE UP in the document

feeder, as required.

5 When all settings are acceptable, press [

NOTE:

It is not possible to select the paper type (Thick, Thin or OHP) directly from the Paper Tray
Selection Screen. Paper type must be selected from the Applications Selection Screen, which can
be accessed by pressing the [APPLICATIONS] on the control panel.

APS, or select a specific paper tray.

OK to return to the Basic Screen.

CANCEL.

PAPER SIZE again,

OK.

START PRINT] from the Basic Screen.

Lens Mode

Paper Size

6 - 19

Section 6 : Basic Operations

Reserve

The Reserve function allows you to start printing the next job immediately after the present
job is completed. While the first job is printing, you can set up the next job so that the
copier reads in the original image(s) and waits until the first printing is completed.

This section describes the procedure of this function and troubleshooting during the reserve
job setting.

Reserve Specifications

❒ Job settings : 2 (output job and one reserve job)
❒ Job No. : 1 to 15

The Job No. assigned to each job will remain until the copier power is
turned off, whether all output jobs are completed or not.
When the Job No. reaches 16, the numbering will return to No. 1 from
the next job assigned to the copier.

❒ The reserve job is available to be set after the copier starts to scan for the output job.
❒ If certain conditions occur while a Reserve job is being set, such as activation of Interrupt

mode, mishandled paper, or depletion of paper, the current output job will cease and
the SETTING indicator on the screen will be replaced by INTERRUPT, JAM or ADD
PAPER, as appropriate. Perform the required measure for the situation at hand.

❒ Incompatible Basic Copy Conditions: Interrupt copying, Scanning in Memory copy, Proof

copy

❒ Incompatible Original Scanning Conditions: Resolution (Very High)
❒ Incompatible Applications: Overlay

Set Reserve Job

Procedure

1 The reserve job setting is available when the RESERVE indication on the Basic

Screen appears clear.

Basic Screen: reserve job available Reserve Setting Screen

6 - 20

Section 6 : Basic Operations

Reserve (continued)

Set Reserve Job (continued)

2 Touch RESERVE to display the Reserve Setting Screen.
3 Set the desired copying conditions.

When the Reserve Setting Screen is displayed, all keys on the LCD and control
panel will function for the reserve setting job.

• When using Platen memory, set the original(s) on the platen glass or RADF, then press
[STORE] to store the image.

• When 1-2, 2-2, Chapter, Combination, Booklet, Image insert, or Book copy is selected,
set the original(s) on the platen glass or RADF, then press [START PRINT] to store the
image.

When all reserve job settings are made, release the reserve job setting function (see
note) by pressing [
then touch

NOTE:

When releasing the reserve job setting function be sure to press [AUTO RESET] before touching
SETTING; otherwise you will be returned to the Basic Screen, not the Basic Screen for the job in
progress.

4 When output job is completed with the reserve job set, the Basic Screen will display

the copying conditions of the reserve job.

NOTE:

You can continue to set reserve job or store the image when output job is completed.

5 Press [START PRINT].

Copying on the reserve job will start.

SETTING. The Basic Screen will resume for the job in progress.

AUTO RESET] while the Reserve Setting Screen is displayed,

6

Operation

Basic

6 - 21

Reserve/

Status

Section 6 : Basic Operations

Reserve (continued)

Troubleshooting in Reserve Setting

Mishandled Paper During the Reserve Setting

If a misfeed occurs with the job in progress while you are setting a Reserve job, the

SETTING indicator on the screen will change to JAM.

Basic Screen

If originals in the Reserve job are already scanned when the misfeed occurs, the Reserve
job will be performed after the jam is cleared and the cleared job is completed.

Procedure

1 Touch JAM to display the Jam Position Screen.
2 To view Help Screen instructions, touch
3 Press [
4 Touch

If scanning is not completed when the misfeed occurs, but Reserve settings were already
made, the Reserve job can be performed after the cleared job is completed. Simply insert
the original document and press [

START PRINT]. The output job will be reprocessed.

SETTING to continue setting the reserve job.

START PRINT].

GUIDE and remove paper/original.

6 - 22

Section 6 : Basic Operations

Reserve (continued)

Troubleshooting in Reserve Setting (continued)

When Paper is Depleted for the Job in Progress

If the paper supply for a job in progress becomes depleted while you are setting a Reserve
job, the

In this case, you can still continue the reserve job setting.

SETTING indicator on the screen will change to ADD PAPER (blinking).

Basic Screen

6

Operation

Basic

Procedure

1 Touch ADD PAPER to display the Basic Screen for the output job.
2 Confirm the empty tray and supply the paper.
3 Press [
4 Touch

START PRINT]. The output job will be reprocessed.

SETTING to continue setting the reserve job.

Reserve/

Status

6 - 23

Section 6 : Basic Operations

Status

Touch the STATUS key on the Basic Screen to display the Job Status Screen (see below).
This screen allows you to confirm machine status for a variety of settings and conditions.
Each field is explained in the next page.
Touch respective keys on the Job Status Screen to display the following subsequent
screens.

❒ User Name Check Screen: Displays user name assigned to the jobs.

NOTE:

User name cannot be assigned to copying jobs.

❒ Previous Job List Screen: Lists 5 completed jobs going back from the current job.
❒ Non Complete Job List Screen: Lists the last 5 jobs which could not be printed in printer

mode.

Basic Screen

User Name Check Screen Previous Job List Screen

Job Status Screen

Non Complete Job List Screen

Procedure

1 Touch STATUS on the Basic Screen.
2 The Job Status Screen displays to show the current machine status.

• To check user name of the job, touch
Name Check Screen. Touch

EXIT to return to the Job Status Screen.

• To view the previous job list, touch
Job List Screen. Touch

EXIT to return to the Job Status Screen.

USER NAME CHECK to display the User

PREVIOUS JOB LIST to display the Previous

• To view the jobs which could not be completed in printer mode, touch

COMPLETE JOB LIST to display the Non Complete Job List Screen. Touch EXIT

to return to the Job Status Screen.

3 When status check is completed, touch

SETTING. The Basic Screen will be restored.

NON

6 - 24

Section 6 : Basic Operations

Status (continued)

JOB No. : Displays the No. (1-15) for each job assigned to the machine.

During an interrupt copying job, the interrupt icon [
this field instead of the number.

MODE: Displays the machine’s current mode of operation. Seven modes are listed

below.
COPIER
RESERVE COPIER
PRINTER
RESERVE PRINTER
CONTROLLER
INTERRUPT

STATUS: Displays the current status of the machine for each job.

[Indication] [Meaning]

READY :Ready to use in each mode
WAITING :Warming up in each mode
SCANNING :Scanning original(s) in copy mode
ERROR :Error in each mode
PRINTING :Printing in each mode
NO PAPER :No paper in copy/print mode
STOP :Stop in each mode
NEXT PRINT :Waiting for the completion of the previous operation

in copy/print mode
INITIALIZING : Initializing for controller
READY TO RESERVE :Ready to reserve
RECEIVING :Receiving the data for controller

] will be displayed in

6

Operation

Basic

TOTAL PAGE(s): Displays the number of scanned pages for each job. (0 to 9999)
PAGE(S) LEFT: Displays the remaining copy count of the job.

0 to 9999 (The number exceeding 9999 will be displayed as 9999↑.)
Copy count = No. of scanned pages x Print quantity

MINUTE(S) TO GO: Displays the time (in minutes) required for completing the job.

Exceeding 999 minutes: 999↑
Shorter than 1 minute: <1

NOTE:

The time displayed is an approximation and may take slightly longer.

Other: The following message will be displayed on the second bar when

the reserved job does not exist.

RESERVED JOB DOES NOT EXIST

6 - 25

Reserve/

Status

Section 6 : Basic Operations

A

R

Memory Copy

Memory copy allows you to scan multiple originals from the platen glass and/or RADF,
then set the desired copy conditions and output the complete set.

Platen Memory Copy

Use Platen memory copy for originals that cannot be fed through the document feeder
due to thickness, size or condition.
When scanning thick originals that require keeping the document cover open, select Non­image area erase to prevent exposure of the glass area around the border of the original.
This feature ensures a clean copy result and reduces toner consumption. The Non-image
area erase mode automatically releases after the original for which it is selected is scanned.
Additional images may be scanned.

Specifications for Platen Memory Copy

❒ Memory is available to store up to 1,500 pages (with maximum memory fitted) unless

memory overflow occurs.

❒ Incompatible Basic copying conditions: None
❒ Incompatible Original Scanning conditions: None
❒ Incompatible Applications: Image insert, Dual page

SPECIAL ORIGINAL

APPLICATION

ROTATION OFF

STORE

Procedure

1

Set Copying Conditions

1 Make required copying selection, and select 1s1 or 1s2 copy mode.
2 Press [

touch
of the [

APPLICATION] on the control panel to display the Application Selection Screen,

MEMORY to highlight it, then touch OK to return to the Basic Screen. The LED

STORE] key will be illuminated.

Application Selection Screen

Control Panel

SPECIAL ORIGINAL

APPLICATION

ROTATION OFF

START PRINT

T

CHECK

JOB ME

6 - 26

STORE

AUTO

Memory Copy (continued)

A

R

T

R

F

T

Platen Memory Copy (continued)

2

Place/Scan Originals on the Platen Glass ... FACE DOWN

1 Open the document feeder.
2 Place original FACE DOWN on the platen glass, then

close the document feeder.

IMPORTANT:

PLACE AND SCAN THE ORIGINALS IN REGULAR
ORDER OF PAGINATION.

Section 6 : Basic Operations

3 Press [STORE] to scan and store the data into memory.

When pressing [

STORE] to light the LED then press [STORE].

[

STORE] does not start scanning, press

4 Repeat Steps 1 and 3 until all originals are scanned.

The number of originals scanned should not exceed the
Exit tray or Finisher capacity.

3

Enter Print Quantity

Enter Print Quantity, using the keypad.
To delete the scanned data without printing, press [

STOP/

CLEAR].

To reset the copying conditions to the initial setting, press

STOP/CLEAR] then [AUTO RESET].

[

4

Start Copying

Press [START PRINT]. The copier starts the printing job.

CAUTION

When the finisher / paper exit tray capacity is exceeded
due to the print quantity selected, remove the copied sets
while the paper is exiting; otherwise, mishandled paper
will occur.

TER

DEM

HELP

ORY

SET

SPECIAL ORIGINAL

ROTATION OFF

PRINT QUANTITY

APPLICATION

STORE

PRINT QUANTITY

RECALL

CLEAR QTY.

PROOF COPY

CHECK

INTERRUPT

JOB ME

AUTO

INTE

PROO

STAR

T

S

Basic

6

Operation

Memory Copy

CLEAR QTY.

RECALL

START PRINT

6 - 27

Section 6 : Basic Operations

Memory Copy (continued)

RADF Memory Copy

Use this feature to scan more than 50 original into memory from the RADF. Use this
function in conjunction with the Reserve function to increase efficiency of the copying job.

Specifications for RADF Memory Copy

❒ Memory is available to store up to 1,500 pages (with maximum memory fitted) unless

memory overflow occurs.

❒ Incompatible Basic Copying Conditions: None
❒ Incompatible Original Scanning Conditions: Resolution (Very high)
❒ Incompatible Applications: Image insert, Dual page

SPECIAL ORIGINAL

APPLICATION

ROTATION OFF

STORE

START PRINT

Procedure

1

Set Copying Conditions

Make required copying selection.

2

Place/Scan Originals ... FACE UP

1 Position originals FACE UP on RADF.

If the number of originals exceeds 50, divide them into blocks not exceeding 50
sheets and load them from the block with the first page.

FACE UP

1~50

2

1

50

7

6

5

4

3

51~100

51

...

...

1451~1500

1451

100

7

6

5

4

3

2

...

1500

7

6

5

4

3

2

...

6 - 28

Memory Copy (continued)

A

R

T

T

RADF Memory Copy (continued)

Section 6 : Basic Operations

2 Press [STORE] to scan and store the data into memory.
3 Load the next 50 originals FACE UP on the RADF.
4 Press [

STORE] to scan and store the data into memory.

5 Repeat steps 3 and 4 until all the originals are stored.

3

Enter Print Quantity

Enter Print Quantity, using the keypad.
To delete the scanned data without printing, press [

STOP/

CLEAR].

To reset the copying conditions to the initial setting, press

STOP/CLEAR] then [AUTO RESET].

[

4

Start Copying

Press [START PRINT]. The copier starts the printing job.

SPECIAL ORIGINAL

ROTATION OFF

PRINT QUANTITY

RECALL

APPLICATION

STORE

CLEAR QTY.

CHECK

JOB ME

INTERRUPT

PROOF COPY

START PRINT

AUTO

T

Basic

6

Operation

S

CAUTION

When the finisher / paper exit tray capacity is exceeded
due to the print quantity selected, remove the copied sets
while the paper is exiting; otherwise, mishandled paper
will occur.

PRINT QUANTITY

RECALL

CLEAR QTY.

INTERRUPT

PROOF COPY

START PRINT

6 - 29

Memory Copy

S

Section 6 : Basic Operations

Output Mode for Machine without Finisher

This section describes three output modes for a copier without the Finisher. For the copier
with Finisher installed, refer to p. 7-2 ~ p. 7-19.

q Sort with normal exit (default)
w Sort with alternate exit
e Group with normal exit

Specifications of Sort with Alternate Exit

❒ Not available for the copier with Finisher
❒ A4, A4R, B5 and B5R, or 8.5"x11" and 8.5"x11"R paper should be loaded in any tray

including Multi-sheet bypass tray.

❒ Use RADF, or operate Memory copy to use platen glass.
❒ Incompatible Basic Copying Conditions: ATS, Tandem mode
❒ Incompatible Original Scanning Conditions: Resolution (Very high), Mixed Original
❒ Incompatible Applications: Sheet/Cover insertion, Chapter, Combination, Booklet, OHP

interleave, Image insert, Dual page, Program job, Non-Image area erase, Repeat image,
AUTO layout, Thin/Thick paper, Overlay

Originals

Sort with normal exit (default)

OUTPUT

STAPLE SORT

SORT

3

2

1

Sort with alternate exit

OUTPUT

STAPLE SORT

Copy paper:
A4 and A4R, B5 and B5R

8.5"x11" and 8.5"x11"R

SORT

Group with normal exit

OUTPUT

STAPLE SORT

SORT

Touch

GROUP on Output

Mode Screen

6 - 30

Section 6 : Basic Operations

T

R

F

Output Mode for Machine without Finisher (continued)

1

Set Copying Conditions

1 Select desired Application functions and Basic copying settings.
2 Return to the Basic Screen.
3 To select Sort with alternate exit, press [SORT] to

illuminate the LED next to the key.

OUTPUT

STAPLE SORT

SORT

To select Group with normal exit, press [
and touch

Control Panel

GROUP to illuminate the LED next to the key.

OUTPUT

STAPLE SORT

SORT

OUTPUT] to display the Output Mode Screen,

Output Mode Screen

To use Sort with normal exit, do not press any output key. No output LED should be
illuminated.

2

Enter Print Quantity

Enter Print Quantity, using keypad.
To delete the scanned data without printing, press [

CLEAR].

STOP/

TER

DEM

PRINT QUANTITY

To reset the copying conditions to the initial setting, press

STOP/CLEAR] then [AUTO RESET].

[

HELP

INTE

PROO

Basic

6

Operation

Output without

Finisher

ORY

SET

RECALL

CLEAR QTY.

STAR

6 - 31

Section 6 : Basic Operations

T

Output Mode for Machine without Finisher (continued)

3

Position Originals ... FACE UP in RADF

... FACE DOWN on the Platen Glass

Position originals FACE UP in the document
feeder.

When using the platen glass and Sort with alternate exit,
activate Platen memory. First, position original FACE
DOWN on the platen glass, then press [
Repeat this operation for all originals.

STORE] to scan.

4

Start Copying

Press [START PRINT].

CAUTION

When the paper exit tray capacity is exceeded due to the
print quantity selected, remove the copied sets while the
paper is exiting; otherwise, mishandled paper will occur.

6 - 32

PRINT QUANTITY

RECALL

CLEAR QTY.

INTERRUPT

PROOF COPY

S

START PRINT

Section 6 : Basic Operations

Rotation

This function allows you to utilize APS or AMS and copy the original size documents
described below onto size A4 or B5, irrespective of the copy paper loading direction. By
default, Rotation requires APS or AMS to function; however, the key operator may set the
function to always function or when APS, AMS or reduce magnification functions. See p.
12-42 to p. 12-46.

Rotation Specifications

❒ Rotation copying uses memory.
❒ Paper size: A4, A4R, B5, B5R
❒ RADF APS detects size: A3, B4, F4, A4R, A4, B5R, B5, A5*1, 8.5"x11"
❒ Platen APS detects size: A3, B4, F4, A4R, A4, B5R, B5, A5*
❒ Incompatible Basic copying conditions: V/H zoom, Tandem mode
❒ Incompatible Original Scanning Conditions: Resolution (Very high)
❒ Incompatible Applications: Dual page, Program job, Non-image area erase, Repeat,

Auto layout, Overlay

NOTE:

*1: A5 original is available in both landscape ( ) and portrait ( ) orientation.
*2: A5 original is available in landscape orientation ( ) only.

2

6

6

Operation

Operation

Basic

Basic

Rotation and APS

In APS with Rotation, the copier automatically makes a copy onto the same size paper as
the original loaded on the RADF or the platen glass, irrespective of the loading direction
of the original and the copy paper.
For example, when size A4 copy paper is loaded landscape in the tray and the copier
detects that the original is placed portrait, Rotation and APS function together to rotate the
original image by 90° and output the A4 copy to match the orientation of the copy paper.

Original Copy paper Rotation and APS

APS cannot be
used alone.

Similarly, when size A4 copy paper is loaded portrait in the tray and the copier detects that
the original is placed landscape, Rotation and APS function together to rotate the original
image by 90° and output the A4 copy to match the orientation of the copy paper.

Original Copy paper Rotation and APS

APS cannot be
used alone.

Output without

Finisher

Rotation

6 - 33

Section 6 : Basic Operations

Rotation (continued)

Rotation and AMS

For example, when size A4 copy paper is loaded landscape in the tray and copier detects
that the original is placed portrait, Rotation (if required) rotates the original image by 90°
and the copy is made with the appropriate AMS ratio to fit the portrait style of the copy
paper.

Original Copy paper Rotation and AMS AMS only

Similarly, when size A4 copy paper is loaded in the tray vertically and the copier detects
that the original is placed horizontally, Rotation (if required) rotates the original image by
90° and the copy is made with the appropriate AMS ratio to fit the landscape style of the
copy paper.

Original

Copy paper

Rotation and AMS

AMS only

When the B5 tray is selected and the copier detects that the original is placed vertically,
Rotation rotates the original image by 90° and the copy is made with the appropriate AMS
ratio to fit the portrait style of the copy paper.

Original Copy paper Rotation and AMS AMS only

6 - 34

Section 6 : Basic Operations

A

R

Rotation (continued)

To Release Automatic Rotation

The copier is initially set to activate the Rotation function automatically.

To release automatic Rotation:

Press [

ROTATION OFF] to light the [ROTATION OFF] LED.

The Rotation function will be cancelled.

To resume automatic Rotation:

Press [

ROTATION OFF] to cancel the Rotation Off mode. The [ROTATION OFF] LED

will go off and the Rotation function will be reactivated.

SPECIAL ORIGINAL

APPLICATION

ROTATION OFF

STORE

CHECK

JOB ME

AUTO

T

Basic

6

Operation

Rotation

6 - 35

Section 6 : Basic Operations

R

T

Check Mode and Proof Copy

Use the Check mode to confirm copying selections before pressing the [START PRINT]
key. The Check Screen allows you not only to view the current settings but to change or
release them directly from the Check mode.
In this mode, use Proof copy to produce a sample of the copied set before copying multiple
copies. This is a convenient and cost effective way of viewing the results of the following
copying selections.

• Copying conditions using Memory copy • Booklet

• Sheet/Cover insertion • Image insert

• Chapter • Dual page

• Combination

With Proof copy, all originals are scanned into memory, and only one set is output after
you press [
Check Screen. After Proof copy, some copying condition keys may appear dimmed in the
Check Screen. As to the copying condition indicated on these dimmed keys, you cannot
change or release the selection.
When [

PROOF COPY] key on the control panel or touch PROOF COPY key on the

START PRINT] key is pressed, the job resumes copying until the job is completed.

Specifications for Check Mode and Proof Copy

❒ All settings made can be viewed in the Check Screen.
❒ Incompatible Basic Copying Conditions with Proof Copy: Group
❒ Incompatible Original Scanning Conditions with Proof Copy: Resolution (Very high)
❒ Incompatible Applications with Proof Copy: None

Procedure

1

Display Check Screen

1 Press [CHECK] on the control panel to display the Check Screen.

Control Panel

ECIAL ORIGINAL

APPLICATION

OTATION OFF

STORE

COPY

PRINTER

TANDEM

CHECK

JOB MEMORY

AUTO RESET

PRIN

HELP

Check Screen

2 Verify the settings made for the current job.

6 - 36

Section 6 : Basic Operations

T

Check Mode and Proof Copy (continued)

2

Make a Proof Copy

1 If necessary, press [PROOF COPY] on the control panel or touch PROOF COPY on

the Check Screen to output a set of sample copy.
If only one copied set is needed and the sample set will do for it, press [

CLEAR] to delete the stored data.

STOP/

Control Panel

PRINT QUANTITY

CLEAR QTY.

RECALL

INTERRUPT

PROOF COPY

START PRINT

S

Check Screen

6

Operation

Basic

You cannot change the selection if the copying
condition key appears dimmed.

2 Touch EXIT (or press [CHECK]) to exit from the Check mode and return to the Basic

Screen.

6 - 37

Check Mode &

Proof Copy

Section 6 : Basic Operations

Check Mode and Proof Copy (continued)

3

Change/Release Settings

If you want to change or release any settings, follow the procedure below.

To change the settings:

1 Touch the desired copying condition key on the Check Screen to highlight it. The

dimmed

NOTES:

• The key which cannot be highlighted shows that the copying condition cannot be changed from

• The following application functions cannot be changed even though highlighted, as the CHANGE

2 Touch CHANGE SETTING. The LCD will display an appropriate screen to change

the copying condition selected.

• Selecting a basic copying condition key will display the Basic Screen.

• Selecting Enhance key will display the Change Enhance Selection Screen.

• Selecting Non STD Size key will display the Non STD Size Setting Screen.

• Selecting an application function key will display the Change Application Selection
Screen.

CHANGE SETTING key will be clear.

the Check Screen.
SETTING key will be kept dimmed: Overlay, Non-image area erase, Reverse image, AUTO

layout.

Check Screen

3 Change the setting as desired, then restore the Check Screen to return to the checking

steps, or to the Basic Screen to start copying.

Density Selection Screen

6 - 38

Section 6 : Basic Operations

T

Check Mode and Proof Copy (continued)

To release the settings:

1 Touch the desired original scanning condition key or application function key on the

Check Screen to highlight it. The dimmed

2 Touch

RELEASE SETTING.

Check Screen

3 Touch YES to cancel the application function, or NO to restore.

YES is touched, the selected function will be released and the key will disappear

When
from the Check Screen.

RELEASE SETTING key will be clear.

6

Operation

Basic

4

Start Copying

Press [START PRINT] when the Basic Screen is displayed.
If set quantity is two or more, the copier will output the rest
except the sample sets.

PRINT QUANTITY

RECALL

CLEAR QTY.

INTERRUPT

PROOF COPY

START PRINT

S

Check Mode &

Proof Copy

6 - 39

Section 6 : Basic Operations

T

Interrupt Mode

Use the Interrupt mode to interrupt copying in progress to perform a simple job. When
interrupt copying is completed, the settings for the initial job restore automatically and the
Basic Screen displays. Press the [
conditions:

• Printing continuously the image stored in the memory

• Scanning the originals into memory

• Scanning the originals into memory while printing in Reserve mode

Specifications for Interrupt Mode

❒ Incompatible Basic copying conditions: Reserve
❒ Incompatible Original Scanning Condition: Resolution (Very high)
❒ Incompatible Applications: None

Procedure

1

Press INTERRUPT Button

To stop the current copying job, press [INTERRUPT]. For
particular jobs in progress, copying will cease only after
certain phases of the immediate operation are completed,
as indicated by LED conditions described below.

• Collectively printing image stored in memory
The [

INTERRUPT] LED blinks until one set of the current

job is printed. Then the LED remains steady for the
temporary job performed in Interrupt mode.

• Scanning originals into memory
The [

INTERRUPT] LED blinks until scanning is completed

for all originals placed in the document feeder. Then, the
LED remains steady for the temporary job performed in
Interrupt mode.

• Scanning originals into memory while printing in Reserve
mode (see Note 1)
The [

INTERRUPT] LED blinks until the copier completes

the current printing job, scans all originals placed on the
document feeder, and prints one set of the Reserved
job. The LED remains steady for the temporary job
performed in Interrupt mode.
The

SETTING indicator on the Basic Screen will change

to

INTERRUPT.

INTERRUPT] key when the copier is in the following

PRINT QUANTITY

RECALL

CLEAR QTY.

INTERRUPT

PROOF COPY

START PRINT

S

6 - 40

Basic Screen Basic Screen in Interrupt Mode

Section 6 : Basic Operations

T

Interrupt Mode (continued)

2

Replace Originals/Set Copying Conditions

1 Remove any document from the platen glass or from the document feeder, if present.
2 Place new original(s) on the platen glass or in the document feeder.

3 The copying settings in Interrupt mode are as follows.

Copy Mode : 1s1
RADF : ON
AE : ON
Lens Mode : 1:1
APS : ON
Print Quantity : 1
Output Mode : Non-sort

6

Operation

Basic

Select other copying features that are compatible with the Interrupt mode, if desired.

3

Start Interrupt Copying

Press [START PRINT].

4

Press INTERRUPT Button Again

When Interrupt copying is completed, press [INTERRUPT] again to return to the settings
of the initial job.

5

Resume Copying

Press [START PRINT] to resume copying, or load the next batch of originals if RADF
memory copying.

NOTES:

1 In Reserve mode, pressing [INTERRUPT] before the copier finishes scanning originals of the

reserve job will clear the settings selected for reserve job.

2 When [CHECK] is pressed during Interrupt Copying, the information displayed reflects the

initial copy job settings. Check mode will not display Interrupt copy job information.

PRINT QUANTITY

RECALL

CLEAR QTY.

INTERRUPT

PROOF COPY

START PRINT

S

Interrupt Mode

6 - 41

Section 6 : Basic Operations

R

T

Help Mode

Use the [HELP] key to access information about the current screen mode and to learn
about setting procedures. The [
Memory and Key Operator Screens.

The Help Screen also includes the Help menu icon in the lower left of the Help Screen.
When touched, the Help Menu Screen displays a list of all of the copier functions. When
a function item is touched, the Help Screen displays information specific to that topic.

Control Panel

COPY

PRINTER

TANDEM

ECIAL ORIGINAL

HELP

APPLICATION

CHECK

HELP] key can be pressed from any screen except Job

Control panel
contrast key

Help Screen

PRIN

Weekly timer key

OTATION OFF

STORE

JOB MEMORY

AUTO RESET

Service call icon

Help Menu Screen

Procedure

1 While in any screen, press [HELP] to display the Help Screen.
2 Touch

TONER, PAPERs, RADF, STAPLE, FOR ASSISTANCE, or the Service call

icon to display specific Help information.

3 For help on operations, touch

HELP MENU in the lower left area of the screen. The

Help Menu Screen will be displayed. Select one of the 6 Help menu items.

4 If the

Control panel contrast key is displayed, you can display the Contrast Adjustment

Screen and adjust the panel contrast. See p. 12-29 for operation. (See note.)

5 The

Weekly timer key display only when the Weekly timer system is activated. Touch

the key to display the settings of the Weekly timer.

6 Touch

EXIT to return to the screen that was displayed before pressing [HELP].

NOTE:

The control panel contrast feature can be adjusted from the Help Screen provided the feature
setting is activated by Service. Contact your service centre if the feature is required.

6 - 42

Using the Multi-Sheet Bypass Tray

T

Section 6 : Basic Operations

The Multi-sheet bypass tray can be used to stack regular 60 ~ 90g/m2 paper, or it can be
used in the single-sheet mode to copy 50g/m

Specifications for Multi-Sheet Bypass Tray

❒ Bypass tray paper size: A3, B4, A4R, A4, B5R, B5, A5*, B6*
❒ Bypass tray paper weight range: 50 ~ 170g/m
❒ Bypass tray capacity: Plain paper (80g/m2); max. 100 sheets

OHP film; 1 sheet only

NOTE:

*: A5 and B6 originals are available in landscape orientation ( ) only.

Procedure

1

Load Copy Paper

1 Open the Multi-sheet bypass tray located on the right

side of the copier.

2

thin stock or 170g/m2 thick stock.

2

6

6

Operation

Operation

Basic

Basic

2 When copying onto thick or thin stock, select the Thin/

Thick paper of the Application mode, then enter Print
quantity and make other compatible copying selections,
as required.
When selecting the OHP interleave of the Application
mode to copy onto OHP film, print quantity is automatically
set to 1.

3 Insert copy paper while adjusting the paper guides to the

paper size.
Insert OHP film one sheet at a time; or, stack paper, up
to 100 sheets 80g/m

2

Enter Print Quantity

Enter Print Quantity, using keypad.
To delete the scanned data without printing, press [

CLEAR].

To reset the copying conditions to the initial setting, press

STOP/CLEAR] then [AUTO RESET].

[

2

.

STOP/

PRINT QUANTITY

RECALL

CLEAR QTY.

INTERRUPT

PROOF COPY

START PRINT

S

Help Mode

Multi-sheet

Bypass Tray

6 - 43

Section 6 : Basic Operations

T

Using the Multi-Sheet Bypass Tray (continued)

3

Select Multi-Sheet Bypass Tray

Touch PAPER SIZE to display the Paper Tray Selection Screen, and touch the Bypass
key to highlight it.

Full-Automatic Mode Screen

4

Position Originals ... FACE UP in RADF

Paper Tray Selection Screen

... FACE DOWN on the Platen Glass

Place originals FACE UP on the document feeder or FACE DOWN on the platen glass.

5

Start Copying

1 Press [START PRINT].
2 When copying is completed, close the Multi-sheet bypass

tray, then press [

AUTO RESET] to restore settings.

6 - 44

PRINT QUANTITY

RECALL

CLEAR QTY.

INTERRUPT

PROOF COPY

S

START PRINT

Section 7: Output Modes

FS-106 Finisher Specifications

FS-108BM Finisher Specifications

Non-Sort Mode Using Primary (Main) Tray

Sort Mode Using Primary (Main) Tray

Staple-Sort Mode Using Primary (Main) Tray

Group Mode Using Primary (Main) Tray

Output Modes Using Secondary (Sub) Tray

Folding and Stapling & Folding Modes Using Booklet Tray (FS-108BM)

Cover Sheet Feeder (FS-108BM with PI-108)

Manual Stapling (FS-108BM)

Output

7

Modes

Finisher

Specifications

Non-Sort

Sort

Staple-Sort

Group

Secondary

Tray

Folding/Stapling

& Folding

Cover Sheet

Feeder

Manual
Stapling

Section 7 : Output Modes

FS-106 Finisher Specifications

Use only paper that is recommended by Konica and stored under the environmental
conditions stated for copy quantity.
Special stock is not guaranteed for reliability or copy quality. Multi-sheet bypass tray,
Interrupt, and OHP interleaving are incompatible with finisher use.

Finisher Type

❒ Primary (Main) Tray with twin staple heads: moving tray type

Secondary (Sub) Tray

Primary (Main) Tray

• Non-Sort Mode
❒ Paper size: A3, B4, F4, A4R, A4, B5R, B5, A5*

2

❒ Paper weight: 60~90g/m

; Special stock (50~59g/m2, 91~170g/m2, OHP film, labels,

hole punch, rag content)

2

❒ Paper capacity for 80g/m

: 500 sheets A5*1, B6*

2,000 sheets A4R, A4, B5R, B5, 8.5"x11"R, 8.5"x11"
1,500 sheets A3, B4, F4

• Sort Mode/Group Mode

❒ Paper size: A3, B4, F4, A4R, A4, B5R, B5, A5*
❒ Paper weight: 60~90g/m

2

❒ Paper capacity for 80g/m2: 500 sheets A5*

2,000 sheets A4R, A4, B5R, B5, 8.5"x11"R, 8.5"x11"
1,500 sheets A3, B4, F4

• Staple-Sort Mode

❒ Paper size: A3, B4, F4, A4R, A4, B5, 8.5"x11"R, 8.5"x11"
❒ Paper weight: 60~90g/m

2

❒ Paper capacity for 80g/m2: 1,000 sheets*
❒ Staple capacity: 50 sheets*3 (5.0mm thick or less)
❒ Staple position: See p. 7-8.

1

, B6*1, 8.5"x11"R, 8.5"x11"

1

1

, 8.5"x11"R, 8.5"x11"

1

2

Secondary (Sub) Tray

• Non-sort and face down exit

• Non-sort and face up exit

• Group and face down exit

• Group and face up exit

1

❒ Paper size: A3, B4, F4, A4R, A4, B5R, B5, A5*

2

❒ Paper weight: 60~90g/m
❒ Paper capacity for 80g/m

; Special stock (50~59g/m2, 91~170g/m2)

2

: 200 sheets

, B6*1, 8.5"x11"R, 8.5"x11"

NOTES:

*1: A5 or B6 paper is available in landscape orientation ( ) only.

2

: Variable according to the number of pages to be stapled. See p. 4-7 for detail.

*
*3: Staple sheet capacity is changeable, and may be set to 45, 40 or 35 by service.

7 - 2

Section 7 : Output Modes

FS-108BM Finisher Specifications

Use only paper that is recommended by Konica and stored under the environmental
conditions stated for copy quantity.
Special stock is not guaranteed for reliability or copy quality. Multi-sheet bypass tray,
Interrupt, and OHP interleaving are incompatible with finisher use.

Finisher Type

❒ Primary (Main) Tray with twin staple heads: moving tray type

Secondary (Sub) Tray
Booklet Tray
Cover Sheet Feeder PI-108 (option)

Primary (Main) Tray

• Non-Sort Mode
❒ Paper size: A3, B4, F4, A4R, A4, B5R, B5, A5*

2

❒ Paper weight: 60~90g/m

; Special stock (50~59g/m2, 91~170g/m2, OHP film, labels,

hole punch, rag content)

2

❒ Paper capacity for 80g/m

: 500 sheets A5*1, B6*

3,000 sheets A4R, A4, B5R, B5, 8.5"x11"R, 8.5"x11"
1,500 sheets A3, B4, F4

• Sort Mode/Group Mode

❒ Paper size: A3, B4, F4, A4R, A4, B5R, B5, A5, 8.5"x11"R, 8.5"x11"
❒ Paper weight: 60~90g/m

2

❒ Paper capacity for 80g/m2: 500 sheets A5*

3,000 sheets A4R, A4, B5R, B5, 8.5"x11"R, 8.5"x11"
1,500 sheets A3, B4, F4

• Staple-Sort Mode

❒ Paper size: A3, B4, F4, A4R, A4, B5, 8.5"x11"R, 8.5"x11"
❒ Paper weight: 60~90g/m

2

❒ Paper capacity for 80g/m2: 1,000 sheets*
❒ Staple capacity: 50 sheets*3 (5.0mm thick or less)
❒ Staple position: See p. 7-9.

1

, B6*1, 8.5"x11"R, 8.5"x11"

1

1

2

Output

7

Modes

Finisher

Specifications

Secondary (Sub) Tray

• Non-sort and face down exit

• Non-sort and face up exit

• Group and face down exit

• Group and face up exit

1

❒ Paper size: A3, B4, F4, A4R, A4, B5R, B5, A5*

2

❒ Paper weight: 60~90g/m
❒ Paper capacity for 80g/m

; Special stock (50~59g/m2, 91~170g/m2)

2

: 200 sheets

, B6*1, 8.5"x11"R, 8.5"x11"

NOTES:

*1: A5 or B6 paper is available in landscape orientation ( ) only.

2

: Variable according to the number of pages to be stapled. See p. 4-8 for detail.

*
*3: Staple sheet capacity is changeable, and may be set to 45, 40 or 35 by service.

7 - 3

Section 7 : Output Modes

FS-108BM Finisher Specifications (continued)

Booklet Tray

• Folding Mode

❒ Paper size: A3, B4, A4R, 8.5"x11"R
❒ Paper weight: 60~90g/m
❒ Number of Folding sheet: 3 sheets max.
❒ Booklet tray capacity: Approx. 100 sheets max.

• Stapling & Folding Mode

❒ Paper size: A3, B4, A4R, 8.5"x11"R
❒ Paper weight: 60~90g/m
❒ Number of Folding sheet: 16 sheets max. (using 80g/m

❒ Booklet tray capacity: Approx. 100 sheets max.

2

; Special stock (80g/m2 paper is recommended)

33 sets max. of 3-sheet-folded booklet

(33 x 3 = 99 sheets)

50 sets max. of 2-sheet-folded booklet

(50 x 2 = 100 sheets)

2

; Special stock (80g/m2 paper is recommended)

2

paper only)

15 sheets max. (using one cover paper)

20 sets max. of 5-sheet-folded booklet

(20 x 5 = 100 sheets)

10 sets max. of 10-sheet-folded booklet

(10 x 10 = 100 sheets)

6 sets max. of 16-sheet-folded booklet

(6 x 16 = 96 sheets)

Cover Sheet Feeder

❒ Paper size: A3, B4, F4, A4R, A4, B5, A5*, 8.5"x11"R, 8.5"x11"

2

❒ Cover paper weight: 50~200g/m

NOTES:

* : A5 paper is available to the manual stapling only.

paper

7 - 4

Section 7 : Output Modes

Non-Sort Mode Using Pr imary (Main) Tray

The Non-sort mode simply means that the offset-stacker finisher modes are not selected.
Copies will be stacked upon exit without being offset by sorted sets.
With the Primary (main) tray initially selected on the Output Mode Screen, FS-106/FS­108BM outputs the printed sheets FACE DOWN in the proper order.

❒ Paper size: A3, B4, F4, A4R, A4, B5R, B5, A5*, B6*, 8.5"x11"R, 8.5"x11"
❒ Paper capacity for 80g/m2: 500 sheets A5*, B6*

2,000 sheets A4R, A4, B5R, B5, 8.5"x11"R, 8.5"x11"
(FS-106)
3,000 sheets A4R, A4, B5R, B5, 8.5"x11"R, 8.5"x11"
(FS-108BM)
1,500 sheets A3, B4, F4

NOTES:

*: A5 or B6 paper is available in landscape orientation ( ) only.

3

2

Go out

OUTPUT

STAPLE SORT

SORT

1

3

2

1

Output

Output

7

7

Modes

Modes

Finisher

Specifications

Non-Sort

Procedure
1 To use the Non-sort mode, be sure the Output, Staple-sort, and Sort indicator lights,

located above each key, are off.

2 Enter the desired print quantity.
3 Position original(s) in the document feeder or on the platen glass, and make copying

selections, as required.

4 Press [

START PRINT] to begin copying in Non-sort mode.

Copies will exit face down, with the page heading toward the front of the copier.

CAUTION:

When the finisher capacity is exceeded due to the print quantity selected, remove the
copied sets while the paper is exiting; otherwise mishandled paper will occur.

7 - 5

Section 7 : Output Modes

Sort Mode Using Pr imary (Main) Tray

Use this mode when you want to output multiple copies of the original set, and have each
sorted set offset upon exit. The staple mode can be selected with the sort mode.
With the Primary (main) tray initially selected on the Output Mode Screen, FS-106/FS­108BM outputs the printed sheets FACE DOWN in the proper order.

❒ Paper size: A3, B4, F4, A4R, A4, B5R, B5, A5*, 8.5"x11"R, 8.5"x11"
❒ Paper capacity for 80g/m2: 500 sheets A5

2,000 sheets A4R, A4, B5R, B5, 8.5"x11"R, 8.5"x11"
(FS-106)
3,000 sheets A4R, A4, B5R, B5, 8.5"x11"R, 8.5"x11"
(FS-108BM)
1,500 sheets A3, B4, F4

NOTES:

*: A5 paper is available in landscape orientation ( ) only.

3

2

1

Light

OUTPUT

STAPLE SORT

SORT

3

2

1

30mm

Procedure
1 Press [

SORT] to select and illuminate the Sort mode.

2 Enter the desired print quantity.
3 Position originals in the document feeder, and make copying selections as required.

When using Memory copy, position original(s) in the document feeder or on the platen
glass, and press [

4 Press [

START PRINT] .

STORE] to scan. See p. 6-26 to p. 6-29.

CAUTION:

When the finisher capacity is exceeded due to the print quantity selected, remove the
copied sets while the paper is exiting; otherwise mishandled paper will occur.

7 - 6

Section 7 : Output Modes

Staple-Sort Mode Using Pr imar y (Main) Tray

Use this mode when you want to offset and staple each copied set. Stapling position and
number of staples (1 or 2) can be designated on the Staple Position Selection Screen,
which is a subsequent screen of the Output Mode Screen.
Each finished set will be offset from the next copied set.
With the Primary (main) tray initially selected on the Output Mode Screen, FS-106/FS­108BM outputs the printed sheets FACE DOWN in the proper order.

❒ Stapled paper at 1 position: A3, B4, F4, A4R, A4, B5, 8.5"x11"R, 8.5"x11" (B5R cannot

be stapled.)

❒ Stapled paper at 2 positions:A4 or 8.5"x11" paper is available in both landscape ( )

and portrait ( ) orientation.
B5 paper is available in portrait ( ) orientation only.
A3, B4 or F4 paper is available in landscape ( )
orientation only.

❒ Paper capacity for 80g/m2: 1,000 sheets (Variable according to the number of pages to

be stapled. See p. 4-7 or p. 4-8 for details.)

❒ Staple capacity: 50 sheets 80g/m2 (5.0mm thick or less)

(Staple capacity is changeable, and may be set to 45, 40, or 35 by service.)

❒ Staple position: 1 oblique staple; 1 parallel staple (FS-108BM only); 2 parallel staples

7

7

Output

Output
Modes

Modes

Light

OUTPUT

STAPLE SORT

SORT

Basic Screen

3

2

3

2

1

3

2

1

1 oblique staple

3

2

3

1

3

2

1

1 parallel staple

Staple position icon

3

2

3

1

3

2

1

2 parallel staples

Sort

Staple-Sort

7 - 7