Konica 7045 GUIDE MANUAL 7045fv2e

Page 1
2

ISW

1 OUTLINE
2 ISW
3 SERVICE
4 DIAGRAMS
Page 2
1 OUTLINE
2 ISW
3 SERVICE
Blank page
Page 3

DESCRIPTION OF ISW

ISW
ISW (In-System Writer) is a process of updating the control programs stored in flash ROM mounted on various control boards in a Konica digital copier without isolating the boards from the copier. Running ISW enables you to upgrade control programs without replacing the boards and maintain the boards during their replacement.
Tools available for running ISW include ISW Trns (PC software), which connects a personal computer (PC) to the digital copier, and ISW Tool, which is a dedicated tool using EPROM.
These tools can be plugged into the ISW connector of the degital copier to directly update the control programs in flash ROM assembled in the unit.
This chapter focuses on instructions on setting up the 7045 to run ISW. For how to run ISW Trns and ISW Tool, refer to Konica ISW (In-System Writer) Servise Handbook.
Note: Procedures for using ISW Tools to update ROM data in Konica ISW (In-system Writer) Servise Handbook
are divided into three types by copier model. For this unit, see “Updating the Type B Model.”
1 OUTLINE
2 ISW
3 SERVICE
2-1
4 DIAGRAMS
Page 4
ISW

SETUP

[1] Boards that Support ISW
1 OUTLINE
The following boards in the 7045 permit programs that use ISW to be rewritten.
CB (control board)
ICB (image control board)
DFCB (RADF control board)
FNSCB (FNS control board)
[2] Operating Method
2 ISW
1. ISW connector
The ISW connector is next to the total counter in the front door.
The connector (DC 5V jack) for the ISW Tool is below the KRDS connector (25-pin).
The cap or seal that covers each connector must be removed only when using it.
3 SERVICE
ISW connector
2. Preparing the copier for re-writing
Before operating the ISW, maintain the copier in ISW mode.
Step
Operation procedure
1
Enter the 25 mode.
2
[25 mode menu screen]
Press the key.
3
[ISW menu screen]
Select the ROM where the ROM data to be
rewritten.
4
[Program rewrite screen]
Pressing key after key is
displayed, cause the machine to be data waiting
condition.
5
Execute the operation according to the
procedures specified in the "Konica ISW
(In-System Writer) Service Handbook."
11. ISW
START
START
KRDS connector
DC5V jack
2-2
Page 5
ISW
Standby state
During data
transmission
During data
rewriting
Rewriting
finished
START
System control (CB) program
Copier
The key is reversed (grey).
Reading data.
Data LED (green) is lit.
LCD screen is extinguished.
Data LED (green) is blinking.
LCD screen is extinguished.
Data LED (green) is blinking.
Return to 25 mode menu svreen.
START
Image control/RADF control/FNS control program
Copier
The key is reversed (grey).
Reading data.
Data LED (green) is lit.
Reading data.
Data LED (green) is blinking.
Writing data.
Data LED (green) is extinguished.
Finished normally.
Data LED (green) is extinguished.
Checksum display in message display area.
1
2
Copier
Error generated during reading.
Printer LED (red) lights.
The LCD screen is extinguished.
The error lamp (red) is lit.
Response method
(1) Press the STOP/CLEAR button on the copier.
(2) Disconnect the cable and then connect the
cable again.
(3) Start from the beginning for both the copier
and the PC.
(1) Disconnect the cable and then connect the
cable again.
(2) Turn the SW1 (main power) and the SW2
(sub power) on the copier OFF and ON.
Data lamp (green) lights.
(3) Send the system control program once again
from the PC.
Cause
Transmitted data other
than system control data.
Abnormality in cable
connection during data
transfer.
1
2
Copier
Error generated during reading.
Printer LED (red) lights.
Error generated during writing.
Printer LED (red) lights.
Response method
(1) Press the STOP/CLEAR button on the copier.
(2) Disconnect the cable and then connect the
cable again.
(3) Start from the beginning for both the copier
and the PC.
(1) Disconnect the cable and then connect the
cable again.
(2) Press the STOP/CLEAR button on the copier.
(3) Start from the beginning for both the copier
and the PC.
Cause
Data for a different control
program was sent.
Abnormality in cable
connection during data
transfer.
3. Display of operation to rewrite data
4. Error displays and response methods
a. System control program
1 OUTLINE
2 ISW
3 SERVICE
b. Image control/RADF control/FNS control program
2-3
4 DIAGRAMS
Page 6
ISW
5. Types and quantity of re-write ROM
1 OUTLINE
When rewriting the copier flash ROM data using the ISW Tool rewriting EPROM must be prepared.
The following table lists rewriting EPROM prepared for this machine.
Caution: Quantity of the rewriting EPROM and
transfer file size are subject to change without previous notice.
2 ISW
Target control program
System control
Image control
RADF control
FNS control
Quantity of ROM
17
2
1
1
ISW Trns file size (. bin file)
Approx. 7.5 MB
Approx. 0.6 MB
Approx. 0.1 MB
Approx. 0.2 MB
6. Re-write precautions using the “ISW Tool”
System control ROM re-write
The re-write operation must be performed to divide the EPROM of the system control ROM into two
3 SERVICE
groups, because of its number of EPROM is more tham 12. The timing (first time data transfer end timing) for the second time the re-write operations is performed is as follows.
The data LED (green) of the operation part changes from flashing to lighting. The remaining EPROM is transferred to the ISW Tool and the ROM data is transferred. The LCD goes off during data transfer. When data transfer is ended, the 25 mode menu screen is displayed. If an error occurs in the second ROM data transfer, perform the operation again from the beginning (first time).
7. Data transfer error
The Print LED (amber) lights if a transfer error occurs. If an error occurs, refer to the section Error handling in the separate ISW Service Handbook and perform the appropriate countermeasures. After the countermeasures are completed, perform the re-write operation again from the beginning.
2-4
Loading...