Page 1
3
KRDS
3 KRDS
Page 2
3 KRDS
Blank page
Page 3
KRDS
KRDS
[1] Specifications
1. Type: Overall control board built-in type.
2. KRDS (Overall control board) Interface between
modem
• RS-232C Compatible
• Baud Rate: Default ; 38.4 kbps
3. Basic Functions
Auto trouble notification
Operation count auto acquisition
Remote control (machine adjustment data,
rewriting of the counter limit, etc.)
Notification of frequent JAM occurrence
Replenish toner notification
Repair and other call buttons
[2] KRDS Setting
This function selects whether to use KRDS.
KRDS allows the copy machine to call up the host
computer periodically and also when there is an
abnormality. Also data in the copier can be changed from
the host computer.
KRDS can execute the above functions for the following
data:
a. Data on the copier's status such as total and PM count.
b. Data on the frequency of the partial copier such as
RADF paper feed count.
c. Data on the copier's error status such as SC (F) /JAM
occurrence code and count.
d. Data on the various adjustments
To use KRDS, set up as follows:
1. Initialize KRDS memory.
2. Set the type of modem and line.
3. Enter host password.
4. Set phone number.
3 KRDS
KRDS setting menu
1. Calling time set
2. Host password set
3. KRDS TEL No. setting
4. KRDS software SW set
5. KRDS setup calling
3-1
Page 4
KRDS
[3] KRDS Set Up
1. KRDS set up item
KRDS set up procedure
Operation procedure
Step
Turn off the modem and connect to the copier
1
using a modem cable (RS-232C, 25P-25P
straight cable) and wall jack using a modular
cable to the modem.
2
Setting the KRDS connection recognition
(25 mode to )
Set copier software DIPSW 12-6 (KRDS
connection recognition) to “1”.
3
Initialize KRDS memory. (47 mode to 1 5 P 9 8 P
to Start button ON)
4
Set KRDS software SW.
(25 mode to to
4. KRDS software SW set
(Select type of modem and dial mode))
Select the type of modem from the bit pattern 0
3 KRDS
to 6 of the KRDS software SW No.1 and dial
mode from the bit pattern 7.
5
Host password setting.
(25 mode to to
2. Host password set
KRDS phone number setting.
6
(25 mode to to
3. KRDS TEL No. setting
Turn off the SW1 (main power) and SW2 (sub
7
power) of the copier.
Turn on the power switch of the modem.
8
Turn on the SW1 (main power) of the copier.
9
10
Check the set up flag setting condition.
(25 mode to
4. KRDS software SW set
on the switch No.33 and bit No.0 indicates “0” (not yet).)
11
Check the KRDS communication mode.
(25 mode to to
4. KRDS software SW set
Check the data in bit No. 2 of switch No. 38.)
It should be set on “0” if communications are via
a modem.
If the setting is different, change the setting.
Preform KRDS set up calling.
12
(25 mode to to
5. KRDS Setup calling
Press the key to start set up.
13
Check the finishing of set up.
14
(25 mode to to
to Completes if the data
4. KRDS software SW set
on the switch No.33 and bit No.0 indicates “1” (finished).)
15
Turn off the SW1 (main power) and SW2 (sub
power) of the copier.
1. Software SW
10.
KRDS setting
10.
KRDS setting
(Refer to *1 and *2)
10.
KRDS setting
(Refer to *3)
10.
KRDS setting
to check that the data
10.
KRDS setting
to
10.
KRDS setting
)
Start
10.
KRDS setting
to
*1: Host password must be 5-digit.
*2: Host password 1 must be specified.
*3: For both the copier and the host side, copier phone
number and host phone number 1 must be
specified.
*4: Refer to the manual of the modem about
specifications for connecting with the modular
cable.
LINETEL
Modem
Wall jack
Modular cable
3-2
Page 5
KRDS
2. Setting the KRDS connection recognition
(1) Plug the power cord of the copier to the outlet.
(When the SW1 (main power) and SW2 (sub
power) of the copier remain off.)
(2) Turn on the SW1 when the SW2 remains off.
(3) Turn on the SW2 while pressing 2 and 5 of the copy
quantity setting buttons simultaneously.
(4) Select the
menu screen.
(5) Select the bit No.6 of the switch No.12, and then
press the
ON
OFF
Caution: If the copier software SW 12-6 (KRDS
1.Software SW
key.
ON
: KRDS recognize
: KRDS not recognized
recognition) is not selected to “1”, the
menu of the KRDS can not be selected.
key on the 25 mode
3. Initializing KRDS memory
(1) Turn off the SW2 when the SW1 remains on.
(2) Turn on the SW2 while holding down 4 and 7 of the
copy quantity setting buttons simultaneously.
(3) Press the start print button after pressing the copy
quantity setting button 1, 5 and P button, then 9, 8,
finally P button again.
I/O check mode
< 15 - 098 > IN: – – OUT: NOW
(4) “NOW” indication will be changed to “FIN” on the
message display.
(5) Turn off the SW2.
4. Setting KRDS software SW
This function allows adjustment of the KRDS software
switches.
Caution: Adjust the software switch while checking
the switch and bit number since the
memory is rewritten every time the bit data
(1 or 0) is changed.
Any bit data that has been incorrectly
changed must be returned to the original
data.
Step
Operation procedure
1
Enter the 25 mode.
2
[25 mode menu screen]
10.
Press the key.
3
[KRDS setting screen]
Press the key.
4
[KRDS software SW set screen]
Use the or keys to set the switch number.
(Note 1)
5
Use the or keys to set the bit number.
(Note 1)
6
Press the or key to set the bit data.
7
Press the key to end the setting.
Note 1: The bit of the switch is written in the non-volatile
memory every time it is changed.
The numbers shown in the message area are defined as
follows:
KRDS setting
4. KRDS software SW set
▲ ▼
▲ ▼
ON OFF
RETURN
3 KRDS
For each switch function, refer to “List of KRDS Software
SWs”.
3-3
Page 6
KRDS
5. Setting type of modem and line
(1) Using the switch No. 01, enter the modem and line
data into the bits 0 to 7, referring to the following
table.
<If telephone line type is “Pulse”>
Bit No.
Modem
intialization command
AT&FE0Q0V1X0S0=1&S0
AT&FE0Q0V1X0S0=1&S0&D2&C1
AT&FE0Q0V1X0S0=1&S0%E0
AT&FE0Q0V1X0S0=1&S0&D2
AT&FE0Q0V1X0S0=1&S0&M5
AT&FE0Q0V1X0S0=1
AT&FE0Q0V1X0S0=1&S0\N5
<If telephone line type is “Tone”>
Bit No.
Modem
3 KRDS
intialization command
AT&FE0Q0V1X0S0=1&S0
AT&FE0Q0V1X0S0=1&S0&D2&C1
AT&FE0Q0V1X0S0=1&S0%E0
AT&FE0Q0V1X0S0=1&S0&D2
AT&FE0Q0V1X0S0=1&S0&M5
AT&FE0Q0V1X0S0=1
AT&FE0Q0V1X0S0=1&S0\N5
7
6
5
4
3
2
1
0
*
0
0
0
0
0
0
0
1
01
0
0
0
0
0
0
1
0
02
0
0
0
0
0
0
1
1
03
0
0
0
0
0
1
0
0
04
0
0
0
0
0
1
0
1
05
0
0
0
0
0
1
1
0
06
0
0
0
0
0
1
1
1
07
0
1
2
3
4
5
6
7
0
0
0
0
0
1
0
0
0
0
0
1
0
0
0
0
0
1
1
0
0
0
0
1
1
0
0
0
0
1
1
0
0
0
0
1
1
0
0
0
0
1
*
1
81
0
0
82
1
1
83
1
0
84
0
1
85
0
0
86
1
1
87
1
Example:
If the initialization command for the modem you are
using is AT&FE0Q0V1X0S0=1&S0 and you have a
pulse-dial telephone line, enter the data for bits 7 to 0
as 00000001:
In hexadecimal <
Be sure to verify with the above charts whether or not
the hexadecimal <
model being used.
Reference:
This machine has a telephone (modem) line type
automatic recognition setting function.
KRDS Software SW:
Switch No.38 and bit No.0
Data 0: off (manual setting)
1: on (line type automatic recognition) (default)
As a result, if this switch is at “1”, Bit No. 7 of Switch No.
1 can be either “0” or “1”.
>, the value is expressed as 01.
*
> output corresponds with the
*
3-4
Page 7
(2) List of KRDS Software SW
: Default value
KRDS
byte
1
2
3
No.
bit
0-6
7
0
1-2
3
4-7
0
1
2
3
4-5
Function Description
Select modem
Dial mode
Data character length
Parity and stop bit
Reserve
Baud rate
Local echo
Result code
Result code form
(displayed result)
Set DCD signal operation
(carrier detect)
Set DSR signal operation
6
0
0
0
0
0
0
0
0
1
0
1
1
1
1
0
Bit pattern
5
4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
1
1
0
1
1
0
0
0
0
0
1
1
0
1
1
3
0
0
0
0
0
0
0
0
1
Don’t
care
0
1
2
1
0
0
0
0
0
0
1
0
1
0
0
1
1
0
0
0
0
0
1
1
1
0
1
1
1
1
1
1
1
0
0
1
0
1
0
1
MSB LSB
7
0
1
0
0
0
0
0
1
Default value
(Hexadecimal)
No setting (No data is sent to modem.)
AT&FE0Q0V1X0S0=1&S0
AT&FE0Q0V1X0S0=1&S0&D2&C1
AT&FE0Q0V1X0S0=1&S0%E0
AT&FE0Q0V1X0S0=1&S0&D2
AT&FE0Q0V1X0S0=1&S0&M5
AT&FE0Q0V1X0S0=1
AT&FE0Q0V1X0S0=1&S0\N5
Manual setting (3 to 24 byte data is sent to modem.)
Pulse dial
Tone dial
8 bit (fixed)
No parity, stop bit 1 (fixed)
Even number of parity, stop bit 1
Odd number of parity, stop bit 1
No parity, stop bit 2
1200 bps
2400 bps
4800 bps
9600 bps
19200 bps
38400 bps
No setting
E0: Exist
No setting
Q0: Exist
No setting
V1: Word
No setting
&C1: ON only when the carrier is detected.
No setting
&S0: Keep ON
&S1: ON during online
&S2
81
81
57
3 KRDS
3-5
Page 8
KRDS
No.
byte bit
3
4
3 KRDS
5
6
7
8
9
10
11
12
13
14
15
16
17
Function Description
6
Check DSR signal
7
Check DCD signal
0-1
Set DTR signal operation
Speaker control
2-3
Display speed when
4-6
connection is completed
and dial/busy tone is
detected.
Reset modem (This is set
7
prior to shipping.)
Arbitrary command regist-
0-7
ration area 1 (ASCII data)
0-7
0-7
Arbitrary command regist-
0-7
ration area 2 (ASCII data)
0-7
0-7
Arbitrary command regist-
0-7
ration area 3 (ASCII data)
0-7
0-7
Arbitrary command regist-
0-7
ration area 4
0-7
Command free setting
0-7
Set S register (bit 0 - 7)
0
Automatic receive ring count
S0:
S6:
1
2
Wait time from off hook
to dial start
S7: Off hook limit timer
6
0
1
0
0
0
0
1
1
1
1
Bit pattern
5
4
0
0
0
1
1
0
1
1
0
0
0
1
1
0
1
1
3
2
1
0
0
1
1
0
0
0
1
1
0
1
1
0
1
0
1
MSB LSB
7
0
1
0
1
0
off
on
off (fixed)
on
0
No setting
1
&D0
0
&D1
1
&D2
No setting
M0: Keep off
M1: ON until communication starts
M2
No setting
No indication of communication speed
X0:
X1: Indication of communication speed
Indication of communication speed; Detect dial tone
X2:
X3:
Indication of communication speed; Detect busy tone
X4:
Indication of communication speed; Detect dial and busy tone
non
non
No setting
&F: This is set prior to shipping.
Send ASCII data specified in this area to modem
0
No setting
1
S0=: Effective data
No setting
S6=: Effective data
No setting
S7=: Effective data
Default value
(Hexadecimal)
57
10
00
01
3-6
Page 9
KRDS
No.
byte bit
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Function Description
S8: Dial stop time (sec.)
3
S9:
4
5
Carrier recognize time
S10: Allowable carrier
stop time
S11
6
Reserve
7
S0 data (No. of times data
was received automatically)
S6 data (Wait time until
dialing starts.)
S7 data (Wait time until
carrier detect)
S8 data (Pause time)
S9 data (Carrier detection
time)
S10 data (Carrier dis-
connection detection time)
S11 data
Timer 1 (Ring reception→
Connect reception)
Timer 2 (Dial call end
→ Connect reception)
Timer 3
Timer 4 (Line Connect → Send
Start-up message request)
Timer 5 (Opposite Party
Signal answer wait time)
Retry data; Timer 6
(Initialization OK →Dial call)
Call when SC error occurs
0
Call specify date
1
Call parts replace date
2
Call drum replace date
3
Call regular service date
4
5
6
Bit pattern
5
4
2
1
3
0
MSB LSB
7
0
1
0
1
0
1
0
1
Don’t
care
00 - FFH
00 - FFH
00 - FFH
00 - FFH
00 - FFH
00 - FFH
00 - FFH
00 - FFH
00 - FFH
00 - FFH
00 - FFH
00 - FFH
00 - FFH
0
1
0
1
0
1
0
1
0
1
Don’t
care
No setting
S8=: Effective data
No setting
S9=: Effective data
No setting
S10=: Effective data
No setting
S11=: Effective data
01H (1)
03H (3)
1EH (30)
03H (3)
06H (6)
0EH (14)
5FH 95
20H (32) x 1sec
40H (64) x 1sec
0AH (10) x 100ms
20H (32) x 100ms
1EH (30) x 1sec
FFH (255) x 5ms
disable
enable
disable
enable
disable
enable
disable
enable
disable
enable
Default value
(Hexadecimal)
01
01
03
1E
03
06
0E
5F
20
40
0A
20
1E
FF
99
3 KRDS
3-7
Page 10
KRDS
No.
byte bit
31
32
33
3 KRDS
34
35
36
37
Function Description
Call regular transmit date
6
Select regular transmit
7
(Time and count)
Call when optional configu-
0
ration is changed
Report of toner
1
replenishment
Report of JAM occur
2
frequently
3-7
Reserve
0
Set up flag
1-2
Radial interval
3-4
Reserve
5-6
Reserve
7
Line feed control
(when initializing modem)
Call JAM date (main body)
0-1
Valid copy quantity
Call ADF JAM date
2-3
Valid original feed quantity
Call JAM date
4-5
MCBJ setting
Call JAM date
6-7
MOBJ setting
Reserve
Reserve
Reserve
0
1
0
1
0
1
Bit pattern
Don’t care
Don’t care
Don’t care
0
0
0
1
1
0
1
1
0
1
0
1
0
0
0
1
1
0
1
1
0
0
1
1
0
0
0
1
1
0
1
1
MSB LSB
76543210
0
1
Don’t care
0
1
0
0
1
1
disable
enable
time
counter
0
disable
1
enable
disable
enable
disable
enable
0
not yet
1
finished
1 min.
3 min.
5 min.
7 min.
CR/LF: LF exist
CR: No LF
0
Copy quantity: level 1
1
Copy quantity: level 2
0
Copy quantity: level 3
1
Copy quantity: level 4
Original feed quantity: level 1
Original feed quantity: level 2
Original feed quantity: level 3
Original feed quantity: level 4
MCBJ: level 1
MCBJ: level 2
MCBJ: level 3
MCBJ: level 4
MOBJ: level 1
MOBJ: level 2
MOBJ: level 3
MOBJ: level 4
Default value
(Hexadecimal)
99
00
0A
55
0A
00
00
3-8
Page 11
KRDS
6
Bit pattern
5
43
No.
byte bit
38
Function Description
0
Line type automatic
MSB LSB
7
recognition
1
MSAD connection
2
KRDS communication
mode
3-5
Reserve
6
PM limit data length
Don’t care
0
1
0
1
39
7
Regular transmit communication
Sequence control
0-1
Reserve
2
RS-232 line error
K01_XX (Note 1)
3
Modem AT command error
K02_XX (Note 1)
Don’t
care
0
1
40
4
Reserve
5
Force copy stop
(at host side) (Note 2)
6-7
Reserve
0
Force copy stop (Note 2)
Don’t care
(at terminal equipment side)
Jam history data clear
1
Reserve
2-5
User data access setting
6
(local)
Resarve
7
Don’t care
0
1
0
Note 1: For details of errors, refer to [7] Error code table.
Default value
2
1
0
0
off
1
on
0
1
0
1
not connect
connect
DATA (Using a modem)
FAX
(Hexadecimal)
88
Upper 2-digit fixed (for host)
All 6-digit (for host)
Call back communication
No call back communication
Don’t care
0
1
0
1
copy enable
copy disable
copy enable
copy disable
disable
00
3 KRDS
enable
0
disable
1
enable
0
1
disable
enable
00
Prohibition
Permission
Note 2: Copy prohibition: If SWs 39-5 and 40-0 are both set to 1, then it becomes impossible to copy.
3-9
Page 12
KRDS
6. Setting host password
This function sets the host password.
(1) Screen selection
Select the
screen to display the KRDS setting menu screen as an
initial screen.
Then select the
the host password setting screen.
(2) Setting method
a. Three patterns can be used to set KRDS host
b. Press the
c. Enter the host password, 5-digit number or
3 KRDS
d. The firstly entered number or alphabet will be
e. After inputting the password, it the
f. Press the
* As the host password is set to “00000” in factory
* Note that the host password setting (Host 1) must
* See the [4] Calling time set menu mode (Arbitrary)
* Do not care “Host 3.”
password. The entry screen, screen contents and
setting method for each pattern are all the same.
Each message, however, is different.
(There are only 2 patterns for a usable password.)
screen.
alphabet, with the numeric keys on the screen and
press the
shifted to the left end.
BACK
pressing the
entered is canceled.
key to set the entered password. The screen will
return to the KRDS setting menu screen.
setting, ensure to change it to the password which
was set by the KRDS host application for
communication.
Confirm the password of host side with KRDS host
application administrator.
be performed.
concerning “Host 2” settings.
10.
KRDS setting
2. Host password set
NEXT
SET
or
RETURN
SET
key, and then press the
SET
key in the 25 mode menu
key to display
or
key.
key, the data that has been
key to 2change the
BACK
key is pressed before
RETURN
NEXT
Operation procedure
Step
Enter the 25 mode.
1
[25 mode menu screen]
2
10.
Press the key.
[KRDS setting screen]
3
Press the key.
[Host password setting screen]
4
Enter password consisting of number and
alphabet.
Press the or key to change the
5
screen, then enter password (up to 2 patterns).
Press the key.
6
Press the key to end the setting.
7
,
KRDS setting
2. Host password set
NEXT
SET
RETURN
BACK
3-10
Page 13
KRDS
Step
1
2
3
4
5
6
7
Operation procedure
Enter the 25 mode.
[25 mode menu screen]
Press the key.
[KRDS setting screen]
Press the key.
[KRDS TEL No. setting screen]
Enter telephone number (15-digit or less) consisting
of number and alphabet with numeric keys.
Press the or key to change the
screen, then telephone number (up to 3 patterns).
Press the key.
Press the key to end the setting.
RETURN
10.
KRDS setting
3. KRDS TEL No. setting
BACK
NEXT
SET
7. Setting the KRDS telephone number
This function sets copier for KRDS and host telephone
number.
(1) Screen selection
Select the
menu screen to display the KRDS setting screen as
an initial screen.
Then select the
display the KRDS TEL No. setting screen.
(2) Setting method
a. Three patterns can be used to set KRDS phone
number. The entry screen, screen contents and
setting method for each pattern are all the same.
Each screen, however, is different.
b. Press the
screen.
c. Enter the telephone number, 15-digit or less
number, with the numeric keys on the screen and
press the
d. The entered number is displayed in the cursor
section displayed in the line 2 of the message
display area. The cursor shifts from left to right
according to the entered.
If more than 15 digit is entered, the number of the
15 digit is rewritten.
e. To reenter the telephone number, press the Stop/
clear button to clear the data then enter the correct
number.
f. If you wish to change the number of an arbitrary
position, press the
cursor to the desired position and reenter.
g. No data has been set for the second row of the
message area prior to shipping.
10.
KRDS setting
3. KRDS TEL No. setting
or
NEXT
key.
SET
<<
key in the 25 mode
key to change the
BACK
or
key to move the
>>
key to
h. The keys except the numeric keys are defined as
follows:
Pause:
,
Wait temporarily for self-dial feed. (2-3 sec.)
Wait:
W
Wait for dial tone such as asynchronous,
etc. (excluding sound guidance).
Tone Dial:
T
Indicate tone dial after this symbol
Pulse Dial:
P
Indicate pulse dial after this symbol
–
Symbol to divide numbers:
(This symbol is ignored when dialing.)
., #, *
i. After inputting the password, it the
BACK
pressing the
entered is canceled.
j. Press the
RETURN
screen will return to the KRDS setting menu
screen.
• Note that the telephone number setting (copier)
and telephone number setting (Host1) must be
performed.
• Refer to [5] Calling time set menu mode
(Arbitrary) for the (Host 2).
• Do not care "Host 3."
:
Use these keys as required such extension
number.
NEXT
or
RETURN
SET
SET
key to set the entered number. The
key is pressed before
key, the data that has been
key, and then press the
,
3 KRDS
3-11
Page 14
KRDS
8. Calling KRDS set up
<Auto set up>
In the host call setting, call the designated host computer
in the set date and time, and transmit each data of the
copier. Refer to the separate KRDS Host Application
Manual for details of the data being handled.
(1) Screen selection
Select the
screen to display the KRDS setting screen.
Then select the
the KRDS software SW set screen.
Check that the software SW 33-0 is set to “0”. After
checking, press the
KRDS setting menu screen.
On the KRDS setting screen, select the
5. KRDS Setup calling
calling screen.
Caution: If the KRDS software SW 33-0 (Set up
3 KRDS
(2) Setting method
a. Press the
Caution: Do not turn OFF the power during
10.
KRDS setting
4. KRDS software SW set
RETURN
flag) is not selected to “0” (not yet). The
KRDS setup calling screen can not be
selected.
key in the screen.
Start
(a) Communication message
Calling the host for setup
Communicating
communication.
(b) Completion message
in the 25 mode menu
key to return to the
to display the KRDS setup
to display
c. Turn off the power to end the operation.
Operation procedure
Step
Enter the 25 mode.
1
[25 mode menu screen]
2
Press the 10.
3
[KRDS setting screen]
Press the key.
[KRDS software SW set screen]
4
Use the , key to select the switch number
to “33” and bit number “0”.
Check that bit data indicates “0”. If not, set to “0”
5
to press the key.
Press the key to return to the KRDS
6
setting screen.
7
[KRDS setting screen]
Press the key.
8
[KRDS Setup calling screen]
Press the key.
Check the message on the screen.
9
Turn off the power to end the operation.
• How to confirm the completion of setup
Confirm the data at bit No. 0 of address 33 in reference
to "4. Setting KRDS software SW."
If "0", setup is not completed.
If "1", setup is completed.
<Manual set up>
This copier machine can be set up manually, other than
the automatical setup as explained above. (The setup is
effective when both the copier and the host have
completed the setup action.)
KRDS setting
4. KRDS software SW set
▲
▼
OFF
RETURN
5. KRDS Setup calling
Start
key.
Calling the host for setup
Communication completed
b. Turn off the power if no completion message is
displayed in ten minutes.
Check that the host computer starting up correct,
host telephone number, cable connection, etc.
then open to calling the host for setup screen
again to press the
Start
key.
• Operation for the copier machine
1. Switch on the power of modem.
2. Set the address No. 33 as referring to "4. Setting
KRDS software SW."
3. Change the data of bit No. 0 from 0 to 1.
0: Set up not completed
1: Set up completed
4. Establish the changed data by pressing the copy
button.
5. Switch off the power of main body.
• Operation for the host computer
For the operation of the host compouter, refer to the
KRDS Host Application Administrator's Manual.
3-12
Page 15
KRDS
[4] Calling Time Set Menu Mode (Arbitrary)
Select the
screen to display the KRDS setting screen as an initial screen.
Then select the
calling time set screen.
10.
KRDS setting
1.Calling time set
Calling time set menu
1. Calling mode-1
2. Calling mode-2
3. Calling mode-3
Press the
screen and return to the KRDS setting screen.
* This host calling setting calls everything to the “Host 2”.
Therefore, it is necessary first to set the “Host 2”
telephone No. and host password.
RETURN
key in the 25 mode menu
key to display the
key to exit the calling time set
1. Setting calling time setting mode
This function sets designated date calling.
(1) Screen selection
Select the
date calling setting) in the calling time set screen to
display the calling mode-1 (designated date calling)
screen.
Press the
(designed date calling) screen and return to the
calling time set screen.
(2) Entering method
a. Enter year, month, day and time using the numeric
keys.
b. The cursor that indicates entering position will be
appeared in the message indication area at line 2.
c. Using the
desired position.
d. If reenter the entered data, press the Stop/clear
button to clear the entered data then enter the data
again.
e. Enter year, month, day and time using the numeric
keys, then press the
f. Enter year, month, day and time as follows.
• The year is entered by inputting 4-digit in the
Christian era.
• The month and day are entered by inputting 2-digit
number. (Example: 1 is entered as 01.)
• The time is entered using 24 hour clock.
(Example: 1:00p.m. is entered as 13.)
• The minute is entered by inputting 2-digit number.
(Example: 1 is entered as 01.)
• Example:
at 1:00 p.m. of January 15, 1998 to
1998/01/15 13:00
g. Press the
is entered and check the entered data.
h. The screen will return to the calling time setting
menu screen if the
without pressing the
entered data will be changed.
1.Calling mode-1
RETURN
key to exit the calling mode-1
<<, >>
key every time data for one item
SET
(Setting designated
key and move the cursor to
key.
SET
RETURN
SET
key is pressed
key. In this case, no
3 KRDS
3-13
Page 16
KRDS
Step
1
2
3
4
5
6
3 KRDS
7
i. Press the
key to end setting. The screen will return to the
calling time set menu screen.
Operation procedure
Enter the 25 mode.
[25 mode menu screen]
Press the key.
[KRDS setting screen]
Press the key.
[Calling time set screen]
Use the (Setting designated
date calling setting).
[Calling mode-1 (Designed date calling)
screen]
Enter year, month and day using the numeric
key on the screen, then press the , key
to move the cursor to entering position of time.
Enter time and minute using the numeric keys on
the screen, then press the key.
Press the to end the setting.
1.Calling mode-1
key, and then the
SET
10.KRDS setting
1.Calling time set
RETURN
RETURN
<< >>
SET
2. Setting regular date & time calling
The copier will call the host at the regular time specified.
(1) Screen selection
Select the
calling setting) in the calling time set menu screen to
display the calling mode-2 (regular data & time
calling) setting screen.
Press the
(regular data & time calling) setting screen and return
to the calling time set menu screen.
(2) Mode selecting method
a. Select and press the desired mode in the
monthly, weekly, daily
There are three mode type (month, week, day)
that can be set.
b. The current selected mode is high lighted
according to the mode key.
At this time, the setting contents will be appeared
in the message indication area at line 2.
2. Calling mode-2
RETURN
key to exit the calling mode-2
(regular data & time
keys.
3-14
Page 17
KRDS
Step
1
2
3
4
5
6
7
8
Operation procedure
Enter the 25 mode.
[25 mode menu screen]
Press the key.
[KRDS setting screen]
Press the key.
[Calling time set screen]
Use the (regular time calling
setting).
[Calling mode-2 (regular time calling) screen]
Press the any key in , ,
keys.
Using the numeric keys on the screen, enter the
day, hour and minute.
(Item that can be input differs from depend on
the mode.)
Press the key.
Press the to end the setting.
10.KRDS setting
1.Calling time set
2.Calling mode-2
SET
RETURN
monthly
daily
weekly
(3) Mode setting method
Perform the operation in each mode as follows:
a. Monthly mode
(a) Using the numeric keys, enter the day, hour
and minute.
(b) Press the
b. If you wish to change the number of an arbitrary
position, press the
cursor to the desired position and reenter.
c. If reenter the entered data, press the Stop/clear
button to clear the entered data then enter the data
again.
d. Weekly mode
(a) Using the numeric keys, enter the day of the
week, hour and minute.
(b) The day of the week is entered using the
numeric keys according to the following
definitions.
1: Monday 2: Tuesday 3: Wednesday
4: Thursday 5: Friday 6: Saturday
7: Sunday
(c) Press the
e. Daily mode
(a) Using the numeric keys, enter the hour and
minute.
(b) Press the
key to enter the input data.
SET
or
<<
key to enter the input data.
SET
key to enter the input data.
SET
key to move the
>>
f. Common operation
(a) The screen will return to the calling time set
menu screen if the
without pressing the
no entered data will be changed.
(b) Press the
key to end setting. The screen will return to
calling time set menu screen.
(c) Enter the number with the numeric keys as
follows:
• The month and day are entered by inputting 2-digit
number. (Example: 1 is entered as 01.)
• The time is entered using 24 hour clock.
(Example: 1:00p.m. is entered as 13.)
• The time is entered using 24 hour clock. (Example:
1:00p.m. is entered as 13.)
• Example:
Monthly mode: 10 17:10
Weekly mode: day 17:10
Daily mode: 17:10
SET
RETURN
SET
key, and then the
key is pressed
key. In this case,
RETURN
3 KRDS
3-15
Page 18
KRDS
3. Setting regular count calling
The copier will call the host at the regular count specified.
(1) Screen selection
Select the
calling time set screen to display the Calling mode-3
(regular count call) screen.
Press the
(Regular count call) screen and return to the calling
time set screen.
(2) Setting method
a. Using the numeric keys on the screen, enter 6-
b. To reenter the entered data, press the stop/clear
c. The entered numerical value is entered from the
3 KRDS
d. The screen will return to the calling time set menu
e. Press the
3. Calling mode-3
RETURN
digit number, regular count value, then press the
key.
SET
button to clear the entered data then enter the data
again.
number of 4 digit. The number is displayed while
shifting from right to left.
screen if the
pressing the
data will be changed.
SET
end the setting. The screen will return to the calling
time set menu screen.
key to exit the Calling mode-3
RETURN
key. In this case, no entered
SET
key then the
(regular count) in the
key is pressed without
RETURN
[5] A Point to Notice for Operation
Be sure to turn OFF and ON the main power of the copier if
the modem power is turned OFF and ON with the main
power OFF.
Reason: To initialize the modem.
(When the KRDS circuit is powered, it automatically initialized the modem following the modem
power ON and OFF operations.
When the main power of the copier is OFF,
however, the KRDS circuit is not powered and
does not initialize the modem after the modem
power ON and OFF operations.
Some types of modem cannot start communication with KRDS unless they are initialized by the
KRDS.)
key to
Operation procedure
Step
Enter the 25 mode.
1
[25 mode menu screen]
2
Press the key.
[KRDS setting screen]
3
Press the key.
[Calling time set screen]
4
Use the (regular count).
[Calling mode-3 (regular count call) screen]
5
Using the numeric keys on the screen, enter
number, regular count value, then press the
SET
key.
Press the to end the setting.
6
10.KRDS setting
1.Calling time set
3.Calling mode-3
RETURN
3-16
Page 19
[6] ASCII Code Table
ASCII is 1 byte code specified by ANSI.
It enables indication of control code, alphabet and number.
KRDS
character
SH
SX
EX
ET
EQ
AK
BL
BS
HT
LF
HM
CL
CR
S0
S1
DE
D1
D2
D3
D4
NK
SN
EB
CN
EM
SB
EC
→
←
↑
↓
binary
0000 0000
0000 0001
0000 0010
0000 0011
0000 0100
0000 0101
0000 0110
0000 0111
0000 1000
0000 1001
0000 1010
0000 1011
0000 1100
0000 1101
0000 1110
0000 1111
0001 0000
0001 0001
0001 0010
0001 0011
0001 0100
0001 0101
0001 0110
0001 0111
0001 1000
0001 1001
0001 1010
0001 1011
0001 1100
0001 1101
0001 1110
0001 1111
hexa-
decimal
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
character
!
"
#
$
%
&
'
(
)
*
+
,
-
.
/
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
binary
0010 0000
0010 0001
0010 0010
0010 0011
0010 0100
0010 0101
0010 0110
0010 0111
0010 1000
0010 1001
0010 1010
0010 1011
0010 1100
0010 1101
0010 1110
0010 1111
0011 0000
0011 0001
0011 0010
0011 0011
0011 0100
0011 0101
0011 0110
0011 0111
0011 1000
0011 1001
0011 1010
0011 1011
0011 1100
0011 1101
0011 1110
0011 1111
hexa-
decimal
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
character
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
O
Q
R
S
T
U
V
W
X
Y
Z
[
¥
]
^
_
binary
0100 0000
0100 0001
0100 0010
0100 0011
0100 0100
0100 0101
0100 0110
0100 0111
0100 1000
0100 1001
0100 1010
0100 1011
0100 1100
0100 1101
0100 1110
0100 1111
0101 0000
0101 0001
0101 0010
0101 0011
0101 0100
0101 0101
0101 0110
0101 0111
0101 1000
0101 1001
0101 1010
0101 1011
0101 1100
0101 1101
0101 1110
0101 1111
hexa-
decimal
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
character
‘
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
{
}
~
binary
0110 0000
0110 0001
0110 0010
0110 0011
0110 0100
0110 0101
0110 0110
0110 0111
0110 1000
0110 1001
0110 1010
0110 1011
0110 1100
0110 1101
0110 1110
0110 1111
0111 0000
0111 0001
0111 0010
0111 0011
0111 0100
0111 0101
0111 0110
0111 0111
0111 1000
0111 1001
0111 1010
0111 1011
0111 1100
0111 1101
0111 1110
0111 1111
hexa-
decimal
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
3 KRDS
3-17
Page 20
KRDS
[7] Error Code Table
Error code CountermeasureContents
K00_00
K00_01
K00_02
K00_03
K00_04
K00_05
K00_06
K00_07
K00_08
K00_09
K00_10
K00_11
K00_12
K00_13
3 KRDS
K01_00
K01_01
K01_02
K01_03
K02_00
K02_01
Connection NG.
No response from other party.
(No detection of start text from host after establishing connection.)
Because copying is taking place, it is impossible to write to the
non-volatile memory and the line is cut.
Password does not match.
Serial number does not match.
Syntactical error.
Write-in indication on an item for which write-in is impossible.
Unread item error.
Signal reception time-out after detection other party response.
Serial number registration completed.
Communications error due to generation of carrier OFF.
Dial tone is not detected within 5 seconds after setting of
x2 and x4 commands.
Busy signal detected.
No tone detected for 5 seconds after input of @ command.
DTR went to OFF or in OFF state.
Cannot open RS-232C.
Cannot close RS-232C.
Response time-out from RS-232C task.
AT command error.
Initializing NG (MODEM).
Example: Modem initializing command no good.
Redial, repeat reception standby.
Redial, repeat reception standby.
Temporarily stop copying.
Check password.
Check serial number.
Redial, repeat reception standby.
Re-operation on host side.
Re-operation on host side.
Redial, repeat reception standby.
Check serial number.
Redial, repeat reception standby.
Check connection of telephone
line.
Redial.
Redial, repeat reception standby.
Check modem power source.
Check RS-232C cable connection.
Turn power on copier OFF and ON.
Turn power on copier OFF and ON.
Check modem power source.
Check RS-232C cable connection.
Turn power on copier OFF and ON.
Possibility of modem malfunction
or software bug.
Check modem power source.
Check RS-232C cable connection.
3-18
Loading...