Konica 7022 WIRING DIAGRAM df314e

Page 1

DF-314

SERVICE HANDBOOK
2001.02 Ver. 3.0
KONICA CORPORATION
TECHNOLOGY SUPPORT CENTER
TOKYO JAPAN
Page 2
CN26NF1780
Page 3

CONTENTS

1
CONTENTS
SAFETY AND IMPORTANT WARNING ITEMS .............
Refer to the 7020/25/30/35 service handbook on page C-1
2
1. OUTLINE
DF-314 PRODUCT SPECIFICATIONS .................. 1-1
[1] Type ........................................................ 1-1
[2] Functions ................................................ 1-1
[3] Machine data .......................................... 1-1
[4] Maintenance ........................................... 1-1
[5] Machine environment ............................. 1-1
CENTER CROSS SECTION ..................................1-2
DRIVE SYSTEM DIAGRAM ................................... 1-3
ORIGINAL CONVEYANCE PROCESS ................. 1-4
[1] Single-side original copy mode ............... 1-4
[2] Double-side original copy mode ............. 1-5
[3] Mixed original copy mode ....................... 1-5
2. UNIT EXPLANATION
EXTERNAL SECTION ........................................... 2-1
[1] Composition ............................................ 2-1
[2] Mechanisms ........................................... 2-1
ORIGINAL FEED/REVERSAL/ORIGINAL EXIT
SECTION ............................................................... 2-2
[1] Composition ............................................ 2-2
[2] Mechanisms ........................................... 2-2
[3] Original feed/conveyance/scan control ... 2-3
[4] Original exit/reversal and conveyance
control ..................................................... 2-5
[5] Original size detection control ................ 2-7
1 OUTLINE
2 UNIT EXPLANATION
3
Assembly
3 DIS./ASSEMBLY
3. DISASSEMBLY/ASSEMBLY
DISASSEMBLY/ASSEMBLY .................................. 3-1
[1] Replacing feed roller/A ........................... 3-1
[2] Replacing the double-feed prevention
roller/A assy ............................................ 3-1
[3] Replacing the read roller ........................ 3-2
[4] Removing and attaching the paper dust
2
removing brush ....................................... 3-3
REVISED EDITION
2
DATE
Feb. 2001
PA GE
METHOD
REPLACEMENT
Page 4
1

OUTLINE

1 OUTLINE
2 UNIT EXPLANATION
3 DIS./ASSEMBLY
Page 5

DF-314 PRODUCT SPECIFICATIONS

DF-314
[1] Type
Type:
Sheet-through Type reversible DF
[2] Functions
Originals Size:
2
Original Type
Plain Original: 35g/m
Special Original: Original feed and convey-
Original Curling: 10mm maximum (35g/m
A3, B4, A4, A4R, B5, A5, A5R, B5R, B6R, 11x17,
8.5x14, F4, 8.5x11, 8.5x11R,
5.5x8.5, 5.5x8.5R
• Only single-side mode is available with B6R
• All sizes are detected automatically.
• Mixing of original size possible.
2
- 130g/m2 fine quality
original
ance ability may be inferior those of 35g/m fine quality original.
The following types of original cannot be used:
• OHP film
• Blueprint masters
• Offset masters
• Bonded original
130g/m
2
high-quality paper)
Original
2
to 130g/m
2
to
Original scan speed (copies per minute)
Mode 7020/25/30 7035
2
Single sided Original 30 35 Single sided Copy Double sided Original 18 18 Double sided Copy
Original Feed Layout:
Face-up placement, centre standard
Original image read Position:
At the slit glass section
1 OUTLINE
2 UNIT EXPLANATION
[3] Machine data
Power Source: DC24V/5V (supplied from the
main body)
Max. Power Consumption:
Max.100VA
Weight: Approximately 10.7kg
2
Machine Dimensions: Length 576mm
(including about 1.1kg for platen)
Depth 498mm
Height 100mm
(Excluding the original feed tray)
3 DIS./ASSEMBLY
[4] Maintenance
Maintenance: Same as the main unit
Machine Life: Same as the main unit
Curling
Maximum number of stacked originals:
50 sheets Maximum (80g/m2)
REVISED EDITION
2
DATE
Feb. 2001
[5] Machine environment
Temperature: 10 to 30˚C
Humidity: 20 to 80%RH
Note: Specifications are subject to change without
notice.
PA GE
1-1
1-1
METHOD
REPLACEMENT
Page 6
DF-314
1

CENTER CROSS SECTION

1 OUTLINE
2 UNIT EXPLANATION
3 DIS./ASSEMBLY
1
Reversal guide
Original conveyance rollers
Registration roller
Read-out roller
Separation roller
Original feed roller
Paper lift-up plate
Double feed prevention roller
Reversal roller
Original exit roller
Exit guide
REVISED EDITION
1
DATE
May 2000
1-2
PA GE
1-2
METHOD
REPLACEMENT
Page 7

DRIVE SYSTEM DIAGRAM

DF-314
1
Original conveyance motor (M302)
Original feed motor (M301)
Original reversal motor (M303)
Original exit roller
Exit guide
Registration roller
Double feed prevention roller
Reversal guide
1 OUTLINE
Separation roller
Original feed roller
Paper lift-up plate
Feed drive
Reversal roller
2 UNIT EXPLANATION
Reversal drive
Roller pressure SD (SD302)
3 DIS./ASSEMBLY
*Reversal and Exit Rollers
A reversal roller pulley is attached to the original exit roller shaft. The reversal roller conveys the original through pressure being applied on the pulley by the roller pressure SD.
Original exit roller
Reversal roller
Pulley
Roller pressure SD (SD302)
Conveyance/exit drive
Exit SD (SD303)
REVISED EDITION
1
DATE
May 2000
1-3
PA GE
1-3
METHOD
REPLACEMENT
Page 8
DF-314

ORIGINAL CONVEYANCE PROCESS

As illustrated below, the DF-314 is made up of a original
1 OUTLINE
feed section, conveyance section, original exit section and reversal section.
Original feed section
Reversal section
Original exit section
Platen glass
2 UNIT EXPLANATION
1
Conveyance section
Slit glass (Read section)
With the originals set face-up on the original feed tray, they are fed from the topmost original. Rather than being conveyed to an original glass surface, the originals that are fed in and read when they pass a slit glass placed in the conveyance path.
The operation mode of the DF-314 consists of 3 modes,
3 DIS./ASSEMBLY
the one-side original copy mode, the two-side original copy mode and the mixed original copy mode.The conveyance method differs for each mode.
[1] Single-side original copy mode
When PS311 turns ON, the original is re-fed by the registration roller and conveyed to the original conveyance roller. The original conveyance roller conveys the original to the position where PS312 (original feed PS) turns ON.
Conveyance rollers
Original feed PS (PS312)
Registration roller
Original registration PS (PS311)
The conveyance roller turns, and scanning starts. If there is another original waiting, it is pre-fed at this point.
The scanning of the original is conveyed out when the original passes over the slit glass. The original which has been read is exited to the original exit tray by the original exit roller with the exit SD OFF (i.e. with the exit guide raised).
Next original
(Single-sidesingle-side copy, single-sidedouble­side copy)
The original that has been set in the paper feed tray is lifted by the paper lift-up plate so it comes into contact with the original feed roller. The original feed roller and the separation roller pre-feed to the position where P311 (original registration PS) turns on.
Separation roller
Registration roller
Original registration PS (PS311)
Original feed roller
Paper lift-up plate
Slit glass
Original exit roller
Exit guide
REVISED EDITION
1
DATE
May 2000
1-4
PA GE
1-4
METHOD
REPLACEMENT
Page 9
DF-314
[2] Double-side original copy mode
(Double-sidesingle-side copy, double-side double-side copy)
The original set in the original feed tray is pre-fed to the position where PS311 (original registration PS) turns ON by the original feed roller and the separation roller. When PS311 turns ON, the reversal guide opens, the registration roller conveys the original to the reversal section, and the reversal roller conveys the original into the interior of the reversal section.
Reversal guide
Original registration PS (PS311)
After the specified period from when PS311 detects the
1
trailing edge of the original and goes OFF, the original is conveyed to the stop position at the front edge of the reversal guide. As the original has been reversed at this point, the reversal roller is made to rotate in reverse and it conveys the original to the original conveyance roller. If there is another original waiting, it is pre-fed at this timing.
Registration roller
Reversal roller
The exit SD comes ON (the exit guide is lowered) when scanning of the rear side of the original begins, and the original is again conveyed to the reversal roller. When PS312 detects the rear edge of the original and turns OFF, the original is conveyed as far as the stop position in front of the reversal gate by the timer. The original has been reversed once again by this point so is conveyed to the original conveyance roller. The original conveyance roller conveys the original and reading of the oliginal face side starts.
Flapper
Original conveyance PS (PS312)
Next original
Reversal roller
Exit guide
Slit glass
The original which has been read is exited to the original exit tray by the original exit roller with the exit SD OFF (i.e. with the paper exit guide raised). If there is another original, it is conveyed to the reversal section at this point.
Next original
Reversal roller
1 OUTLINE
2 UNIT EXPLANATION
3 DIS./ASSEMBLY
The original conveyance roller conveys the original to the position where PS312 turns ON and the reading of the original back side starts.
1
Reversal guide
Flapper
Conveyance roller
Next original
Reversal roller
Exit roller
Slit glass Exit guide
[3] Mixed original copy mode
The mixed original copy mode supports both same-series originals and different series originals, but as size detection is performed in PS311 ON time, size detection is performed before reading.
After the size of the original is detected, the original stops
1
at the reversal position. Subsequently, operation is the same as that of the two-sided copy mode.
Refer to "ORIGINAL FEED/REVERSAL/ORIGINAL EXIT SECTION [5] Original size detection control" for size detection operation.
REVISED EDITION
1
DATE
May 2000
1-5
PA GE
1-5
METHOD
REPLACEMENT
Page 10
2
1
1 OUTLINE
2 UNIT EXPLANATION
3
Assembly

UNIT EXPLANATION

3 DIS./ASSEMBLY
Page 11

EXTERNAL SECTION

DF-314
[1] Composition
1
Jam access cover
[2] Mechanisms
Mechanism System
Jam release* Jam access cover
Reversal guide open/close lever
RADF Main body open/close
Knob
Exit-guide open/close lever
Platen separation lever
Original feed tray
Original exit tray
If a jam occurs in the reversal section, open the reversal guide with the reversal guide open/close lever and withdraw the sheet.
1
Reversal guide open/close lever
1 OUTLINE
2 UNIT EXPLANATION
3 DIS./ASSEMBLY
* Jam removal
If a jam occurs at the original feed, open the Jam access cover and turning the knob closer to you withdraw the sheet.
1
Jam
access
cover
Knob
Reversal
guide
If a jam occurs in the conveyance section, open the exit tray (using the platen separation lever) and the exit guide (using the exit-guide open/close lever) and withdraw the sheet.
Exit guide
Exit guide open/close lever
Platen separation lever
Original exit tray
REVISED EDITION
1
DATE
May 2000
2-1
PA GE
2-1
METHOD
REPLACEMENT
Page 12
DF-314
1

ORIGINAL FEED/REVERSAL/ORIGINAL EXIT SECTION

1 OUTLINE
[1] Composition
1
Original feed unit
2 UNIT EXPLANATION
Jam access cover
Exit SD (SD303)
Roller pressure SD (SD302)
3 DIS./ASSEMBLY
[2] Mechanisms
Mechanism System
Original feed Feed roller
Double feed prevention Separation roller
Double feed prevention Roller
Original conveyance Original conveyance rollers
Original reverse and Reversal guide feed *1
Original exit path Original exit guide section *2
Original feed tray
Original exit tray
Original
reversal
motor
(M303)
Original conveyance motor (M302)
Original reversal motor (M303)
Original feed motor (M301)
Reversal guide
Reversal guide
*1: Reversed original feed
During double-side copying, in order to reverse the original the paper feed path is switched by the reversal guide, the paper is conveyed to the reverse mechanism and is reversed.
REVISED EDITION
1
DATE
May 2000
2-2
PA GE
2-2
METHOD
REPLACEMENT
Page 13
DF-314
*2: Original exit path switching
In the case of a two-sided copy, the paper exit guide
1
changes over the paper feed path so as to either exit the original directly, or feed the original to the reversal section in order to read it once again.
Exit guide
Exit guide
Exit SD (SD303)
[3] Original feed/conveyance/scan
control
24VDC
24VDC M301 OUT A M301 OUT A M301 OUT B M301 OUT B
24VDC
24VDC M302 OUT A M302 OUT A M302 OUT B M302 OUT B
MAIN BODY
M TXD
M REQ
S ACK
M ACK
S TXD
S REQ
24VDC 24VDC
PGND PGND
5VDC SGND SGND
5VDC
VV
DF CB
5VDC
PS301
SGND
5VDC
PS303
SGND
5VDC
PS311
SGND
5VDC
PS312
SGND
M301
M302
PS301
PS303
PS311
PS312
1 OUTLINE
2 UNIT EXPLANATION
3 DIS./ASSEMBLY
Original feed is achieved by the transmission of the M301(original feed motor) drive power to the original feed roller, separation roller and registration roller. Original conveyance is achieved by the transmission of the M302 (original conveyance motor) drive power to the original conveyance roller.
The M301 and M302 are controlled by the DFCB (RADF control board).
REVISED EDITION
1
DATE
May 2000
2-3
PA GE
2-3
METHOD
REPLACEMENT
Page 14
DF-314
1. Operation
1 OUTLINE
a. Original feed
Original feed is started by the transmission of the M301 drive power to the original feed roller, separation roller and paper lift-up plate.
b. 1st original pre-feed
When the copy button is pressed, the M301 starts original pre-feed, and when the conveyed original arrives at PS311, M301 stops temporarily after a specified time. M301 then rotates in reverse, turning
2 UNIT EXPLANATION
the registration roller so that feeding starts again. The original passes PS311, so that PS311 turns OFF. A predetermined time interval after PS311 turns OFF, M301 also turns OFF.
c. 2nd original pre-feed
When there is still an original in the original feed tray, M301 starts after a specified time after PS311 has
3 DIS./ASSEMBLY
turned OFF, and starts the pre-feed from after the second sheet. The original is conveyed in the same way as in the 1st. original pre-feed.
2. Signals
a. Input signals
(1) PS301(PS301 DF CB)
Original feed tray no-paper detection signal
[L] : Original
[H]: No original
(2) PS303(PS303 DF CB)
Original exit section original detection signal
[L] : No original
[H]: Original
(3) PS311(PS311 DF CB)
Original conveyance roller entrance original detection signal
[L] : No original
[H]: Original
(4) PS312(PS312 DF CB)
Original detection signal from detector in front of scan position
[L] : No original
d. Scanning operation (except last original)
When the original arrives at PS311, M302 starts after a specified time has elapsed and the original is conveyed to the read section.
Scanning of the original is achieved when the original passes over the surface of the slit glass of the main body optical section.
When the original arrives at PS312, scanning is started after a specified time has elapsed, and when PS312 turns OFF after the original has passed, scanning is stopped after the lapse of a fixed period of time.
e. Scanning operation (last original)
During the scanning operation, when PS301(no original detect PS) turns OFF, the original currently being scanned is judged to be the last original. When the last original has passed PS311, M301 turns OFF after the lapse of a fixed period of time, and when the original has passed PS303 (original exit PS), M302 turns OFF after a specified time.
[H]: Original
(5) M TXD (MAIN BODY DF CB)
Serial data line; informs RADF of the operating state of the main body's CB
(6) M REQ (MAIN BODY DF CB)
Transmission request signal from main body to RADF
(7) S ACK (MAIN BODY DF CB)
Transmission OK signal from main body to RADF
2-4
Page 15
DF-314
b. Output signals
(1) M301 OUT A, M301 OUT A
, M301 OUT B,
M301 OUT B– (DF CB M301)
M301 drive control signal
24V
0V
(2) M302 OUT A, M302 OUT A
, M302 OUT B,
M302 OUT B– (DF CB M302)
M302 drive control signal
24V
0V
(3) M ACK (DF CB MAIN BODY)
Transmission OK signal from RADF to main body
(4) S TXD (DF CB MAIN BODY)
Serial data line; informs the main body's CB of the RADF operating state
(5) S REQ (DF CB MAIN BODY)
Transmission request signal from RADF to main body.
[4] Original exit/reversal and
conveyance control
24VDC
24VDC M301 OUT A M301 OUT A M301 OUT B M301 OUT B
24VDC
24VDC M302 OUT A M302 OUT A M302 OUT B M302 OUT B
24VDC
24VDC M303 OUT A M303 OUT A M303 OUT B M303 OUT B
MAIN BODY
M TXD
M REQ
S ACK
M ACK
S TXD
S REQ
24VDC 24VDC
PGND PGND
5VDC SGND SGND
5VDC
VV
DF CB
24VDC
SD302
24VDC
SD303
5VDC
PS311
SGND
5VDC
PS312
SGND
The exit guide used in exit path switching is driven by the SD303 (exit SD).
M301
M302
M303
SD302
SD303
PS311
PS312
1 OUTLINE
2 UNIT EXPLANATION
3 DIS./ASSEMBLY
Reversal conveyance drive in double-side copy mode is performed by the M303 (original reversal motor). The reversal roller pressure/freeing used in reversal original feed is performed by the SD 302 (roller pressure SD).
M303, SD302 and SD303 are controlled by the DF CB (RADF control board).
2-5
Page 16
DF-314
1. Operation
1 OUTLINE
a. Original exit operation
During single side copying and face side copying in double-side copying, the exit guide is raised because SD303 is OFF. For this reason, an original which has been read is conveyed to the exit section.
b. Reversal original exit operation
During back side copying in double side copying, the original is conveyed to the scanning section by reverse rotation of M303 and nomal rotation of M302.
2 UNIT EXPLANATION
When PS312 turns ON, SD302 turns OFF, and reversal roller paper pressure conveys the freed original to the reversal section.
c. Reversal original feed operation
After PS312 has detected the rear edge of the original, SD302 turns ON after a specified time has elapsed and the reversal roller applies pressure
3 DIS./ASSEMBLY
(seizes, pinches) to the original. After that, M303 stops, but then immediately reverses and starts the original feed operation of the original face side scan.
2. Signals
a. Output signals
(1) M301 OUT A, M301 OUT A
M301 OUT B– (DF CB M301)
M301 drive control signal
24V
0V
(2) SD302 (DF CB SD302)
SD302 drive control signal
[L] : ON
[H]: OFF
(3) SD303 (DF CB SD303)
SD303 drive control signal
[L] : ON
[H]: OFF
, M301 OUT B,
d. Pre-feed operation of next original when
reading back side of original
PS311 turns OFF once the first original has passed, and after a specified period of time has elapsed, starts the pre-feed operation for the 2nd. original. After the elapse of a specified time after the 2nd. original has arrived at PS311, M301 (original feed motor) stops.
e. Overlap control
When scanning of the back side of the first original
1
sheet has been completed and the leading edge of the original fed from the reversal section reaches PS312, M301 turns ON and feeding of the second original starts. At this time, the SD302 goes OFF, causing the pressure on the reversal roller and the paper exit roller to be released. This enables the first and second originals to pass over each other in opposite directions in the reversal unit.
REVISED EDITION
1
DATE
May 2000
2-6
PA GE
2-6
METHOD
REPLACEMENT
Page 17
DF-314
[5] Original size detection control
DF CB
5VDC PS306 SGND
5VDC PS307 SGND
5VDC PS311 SGND
5VDC
VR301
SGND
PS306
PS307
PS311
VR301
M TXD
M REQ
S ACK
M ACK
S TXD
S REQ
VV
24VDC 24VDC
PGND PGND
5VDC SGND SGND
5VDC
MAIN BODY
Size detection on an original set in the original feed tray is performed by PS306 (original size detect PS1), PS307 (original size detect PS2), and VR301 (size detect VR).
Note that the DF CB includes internal nonvolatile memory that stores timing data, size-detection reference values, and other such data.
b. Original size detection in mixed-original
modes and Z-fold-original modes (1st sheet)
(1) Drum axis direction size detection
The width of the maximum sized original being mixed-loaded is detected by the position of the VR301 guide plate.
(2) Size detection in original feed direction
Original feed direction size is detected during PS311 ON time (the time taken by the original to pass PS311).
(3) Operation of size detection in original feed
direction
When original re-feed is started by the registration roller, when a specified time has elapsed after PS311 turning ON, M303 (original reversal motor) turns ON and conveys the original to the reversal section.
PS311 (Original registration PS)
1 OUTLINE
2 UNIT EXPLANATION
3 DIS./ASSEMBLY
1. Operation
a. Normal copy mode
The DF CB detects the original size when the signals described below combine.
(1) Drum axis direction size detection
VR301 resistance value changes in the position where the guide plate contacts VR301. The width of the original is detected by the resistance value.
(2) Size detection in original feed direction
The length of the original is detected by the ON/OFF states of PS306 and PS307.
Conveyance to the scanning section is performed by M303 reverse rotation.
Conveyance or scanning thereafter for both single and double-sided originals is performed by the same operation as for double-side copy mode. However in single-side copying, the back side of the original passes the scanning section without being scanned and is conveyed to the reverse section.
Original size detection operation after the 2nd. original starts after the completion of the exit of the first original.
2-7
Page 18
DF-314
c. Allowed size combination
1 OUTLINE
( : same size, : same series, : different series, : no mixed loading, : not supported)
(1) AB series
1
Other originals A3 A4 B4 B5 A4R A5 B5R A5R
A3
A4
B4
B5
2 UNIT EXPLANATION
A4R
A5
B5R
A5R
Standard originals (the maximum original size detected by the guide plate)
(2) Inch series
1
3 DIS./ASSEMBLY
Other originals 11x17 8.5x11 8.5x14 8.5x11R 8.5x5.5 8.5x5.5R
11 x 17
8.5 x 11
8.5 x 14
8.5 x 11R
8.5 x 5.5
8.5 x 5.5R
Standard originals (the maximum original size detected by the guide plate)
2. Signals
a. Input signals
(1) PS306 (PS306 DF CB)
Detection of original's length
[1] : Original
[2] : No original
(2) PS307 (PS307 DF CB)
Detection of original's length
[1] : Original
[2] : No original
(3) VR301 (VR301 DF CB)
Detection of original's width
REVISED EDITION
1
DATE
May 2000
2-8
PA GE
2-8
METHOD
REPLACEMENT
Page 19
3

DISASSEMBLY/ASSEMBLY

1 OUTLINE
2 UNIT EXPLANATION
3 DIS./ASSEMBLY
Page 20
1 OUTLINE
2 UNIT EXPLANATION
3 DIS./ASSEMBLY
This section explains how to disassemble and reassemble the machine. Observe the following precautions when performing disassembly and assembly work.
1. Be sure the power cord has been unplugged from the wall outlet.
2. The disassembled parts must be reassembled following the disassembly procedure in reverse unless otherwise specified.
3. Care should be taken not to lose small parts. Care should also be taken not to install small parts in wrong places.
4. Do not operate the machine before installing all the disassembled parts completely.
5. Removal of some screws is prohibited in this section. Never loosen them.
Page 21

DISASSEMBLY/ASSEMBLY

1
DF-314
Caution: Make sure the power plug is taken
out of the socket.
[1] Replacing feed roller/A
(1) Open jam access cover.
(2) Take out the 2 fixed screws and lifting the feed unit
lightly draw it forwards towards yourself and remove it.
1
Feed unit
(3) Remove the E-rings on the ends of the paper-feed
unit (one E-ring on each end), and remove the feed roller/A assy.
(4) Remove feed roller/A from the bearing of the feed
roller/A assy.
Set screws
Feed unit
Feed roller/A
[2] Replacing the double-feed
prevention roller/A assy
(1) Open jam access cover.
(2) Remove feed unit.
1
(6) Remove double feed prevention roller.
1
Jam access cover
Feed unit
Double feed prevention roller
1 OUTLINE
2 UNIT EXPLANATION
3
Assembly
3 DIS./ASSEMBLY
E-ring
Feed roller/A assy
E-ring
E-ring
(5) Install by reversing the removal procedure.
Caution: When installing the feed unit, insert the
unit in order to fit the D cut side on the drive shaft in the coupling.
E-ring
Double-feed prevention roller/A assy
Double feed prevention roller
REVISED EDITION
1
DATE
May 2000
3-1
PAG E
3-1
METHOD
REPLACEMENT
Page 22
1
DF-314
(4) Remove the E-ring from the double-feed prevention
1 OUTLINE
(5) Pull out the double-feed prevention roller/A assy.
2
Unit
2 UNIT EXPLANATION
3
Assembly
(6) Install by reversing the removal procedure.
Caution: When installing the double-feed prevention
3 DIS./ASSEMBLY
roller/A assy.
E-ring
Double-feed prevention roller/A assy
roller, make sure you install it in the correct direction.
E-ring
Paint mark
1
[3] Replacing the read roller
(1) Remove the 3 set screws, and remove the cover.
Set screws
Cover
Set screw
(2) Remove the set screw, and remove the guide.
Next, remove the E ring at the top of the read roller and also the bearing at the bottom together with the E ring fixing it.
Set screws
Guide
E-ring
E-ring
REVISED EDITION
1
DATE
May 2000
3-2
PA GE
3-2
METHOD
REPLACEMENT
Page 23
DF-314
1
(3) Move the read roller upward, then take out the pin
and remove the gear. Move the lower bearing, then pull out the shaft of the read roller.
Gear
Pin
Read roller
Read roller
Bearing
(4) Reinstall the read roller in the opposite sequence to
removal.
Caution: Use glass cleaner to clean the roller if it is
dirty.
[4] Removing and attaching the paper
2
dust removing brush
( 1 ) Open the cover.
( 2 ) Remove the set screw, and then remove the paper
dust removing brush.
Paper dust removing brush
Set screw
(3) Attach the paper dust removing brush in the
opposite sequence to removal.
1 OUTLINE
2 UNIT EXPLANATION
3
Assembly
3 DIS./ASSEMBLY
REVISED EDITION
2
DATE
Feb. 2001
3-3
PAG E
3-3
METHOD
REPLACEMENT
Loading...