FLYWHEEL HORSEPOWER
40.5 kW 54 HP @ 1850 rpm
OPERATING WEIGHT
7670 kg 16910 lb
BUCKET CAPACITY
0.28 m30.37 yd
3
Photos may include optional equipment.
Form No. CEN00132-01
Materials and specifications are subject to change without notice
is a trademark of Komatsu Ltd, Japan
Printed in Japan 200805 IP.As(05)
PC
78UU
COMPACT
HYDRAULIC EXCAVATOR
www.Komatsu.com
PC78UU-6 Compact Hydraulic Excavator
Lessen
tail swing
radius
510mm 1'8"
2440mm 8'0"
1200mm 3'11" 1240mm 4'1"
E
for higher production
Active mode
E
for less fuel consumption
Economy mode
Active mode
Economy mode
Active mode
Economy mode
Active mode
Economy mode
100
105
93
100
Ratio of hourly fuel consumption (%)
Ratio of hourly production (%)
3
PC78UU-6
COMPACT HYDRAULIC EXCAVATOR
Road & Bridge Work
Round form uses Tight Tail and Forward
Facing Design
The PC78UU design uses a Tight Tail concept for both
ends. This makes rotating the machine fast, easy and
confident. There is less to worry about in tight space
conditions because there is little protrusion from either
the tail end or the front end.
2540mm
180-degree
swing width
8'4''
2
PRODUCTIVITY
FEATURES
PRODUCTIVITY
FEATURES
Two working modes give a choice between
high production and low fuel consumption
Powerful swing
force increases
work efficiency
on slopes
PC78UU-6’s superior traveling
speed and power also provide
higher movility
New pressure-compensated CLSS hydraulic
system HydrauMind
Even when 2 or more actuators are operated
simultaneously, the PC78UU-6's pressurecompensated CLSS system ensures that each
actuator works
according to its
control input without
affecting the size of
the load. This gives
the operator precise
control at all times.
Engine speed sensing=Optimum Power
Power utilized by main pump is adjusted automatically in accordance with the engine speed.
That means this computerized system keeps
engine speed even under high load condition.
Back fill blade
The PC78UU features a standard
back fill blade that can quickly and
conveniently fill trenches and clear
up jobsites.
Photo may include optional equipment.
Bucket interference prevention system
The bucket automatically stops itself
from contact with the cab/canopy.
During operation, an alarm sounds
and the equipment is stopped if the
bucket gets too close to contact.
This feature helps maintain operator
confidence, which can increase productivity.
Digital Depth Display
Ditching, trenching, or digging is even more efficient with this
automatic depth measurement system. Informing the operator
of dig depth from ground level (absolute depth) and the depth
from any pre-set point (relative depth) enables work to go
much more smoothly and efficiently. This lessens the need for
the operator to stop operation or leave the cab after each
adjustment, which also increases productivity.
Height Limiter
An adjustable boom height limiter can be set prior to operation. When the boom reaches the pre-set height limit, an
alarm will sound and the boom automatically stops. This
function can help increase productivity by letting operators
focus more on digging in tight or confined spaces.
Lessen
implement
radius
550mm 1'10"
PC60
7
PC78UU-6
COMPACT HYDRAULIC EXCAVATOR
SPECIFICATIONS
SPECIFICATIONS
DRIVES AND BRAKES
Steering control
Drive method
Hydraulic motors
Maximum drawbar pull
Maximum travel speed: High
Low
Parking brakes
UNDERCARRIAGE
Track Adjustment of the track tension
Number of shoes
Number of carrier rollers
Number of track rollers
Ground Pressure
OPERATING WEIGHT (APPROXIMATE)
Operating weight including 1720 mm 5'8" arm, bucket with
0.28 m
3
0.37 yd3 capacity, blade, operator, lubricant,
full fuel tank, and standard equipment.
COOLANT AND LUBRICANT CAPACITY
Fuel tank
Radiator
Engine Oil (Refilling)
Hydraulic (Refilling)
Two levers with pedals
Fully hydrostatic
Variable displacement, axial piston motors
65.1 kN 6640 kg 14639 Ib
4.5 km/h 2.8 mph
3.0 km/h 1.9 mph
Mechanical disk
Grease
39 each side
1 each side
5 each side
0.33 kg/cm
2
4.7 psi
125 Itr 33 USgal
10.5 Itr 2.8 USgal
7.5(7.0) Itr 2.0(1.8) USgal
120(64) Itr 31.7(16.9) USgal
ENGINE
Model
Typ e
Aspirator
Number of cylinders
Piston displacement
Flywheel horsepower
(SAE J1349 NET)
HYDRAULIC SYSTEM
Typ e
Pump:
For implement
Maximum flow
For swing and blade
Maximum flow
Auxiliary Hydraulic flow (opt.)
Valve rating :
Relief valve setting for implement
Relief valve setting for swing and blade
Bucket digging force (ISO)
Arm crowd force (ISO)
with arm length 1720 mm 5'8"
ELECTRIC SYSTEM
Operating voltage
Battery
Alternator
Starter
SWING SYSTEM
Driven method
Swing speed
180-degree swing width
Komatsu S4D95LE-3
Water-cooled, 4-cycle, direct injection
Turbocharged
4
3.26 Itr 199 in
3
40.5 kW 54 HP @ 1850 min-1 1850 rpm
HydrauMind (Hydraulic Mechanical
Intelligence New Design) system,
Closed-center system with load-sensing valve
and pressure-compensated valve
Variable displancement, axial piston
80.0 Itr x 2 = 160 Itr/min 42.2 USgal/min
Fixed displacement gear
60 Itr/min 15.9 USgal/min
113 Itr/min 29.9 USgal/min
270 kg/cm
2
3839psi
210 kg/cm
2
2986psi
6250 kg 13780 lb
3960 kg 8730 lb
24 V
55 Ah
25 A
3.0 kW
Hydrostatic
10.0 rpm
2540 mm 8'4"
Dimensions Working Range
450 mm 17.7" 7670 kg 16,910 lb
Shoe Width Operating Weight
380 1'3''
245 9.6''
5460 17'11''
6240 20'6''
6400 21'0''
1200 3'11''
3190 10'6''
7330 24'1''
4230 13'10''
5260 17'3''
3795 12'5''
2440
(8feet)
4145 13'7''
1170 3'10''
1915 6'3''
1
3
0
0
2325 8'1''
360 1'2''
735 2'5''
2320 7'7''
1240 4'1''
1745 5'9''
2730 8'11''
470 1'7''
6060 19'11''2330 7'8''
1870 6'2''
2235 7'4''
450 1'6''
2320 7'7'' 2840 9'7''
125 5''
750 2'6''
1065 3'6''1030 3'5''
400 1'4''
4
'3
''
20 0.8''
Ideal performance has been achieved with combining the merits
of rubber and the strengths of steel in the new Road-Liner shoes.
Road-Liners can last up to twice as long as conventional rubber
tracks under most normal operating conditions.
Similar to all rubber tracks, pavement is not easily damaged.
Replacement is fast and easy.
Repair cost reductions are possible
by replacing only the damaged or
worn-out shoes, which differs from
the need to replace a full rubber or
steel track.
6
ROAD-LINER (optional)
Rubber thickness has been upgraded using
a new type of core bar, and this section that
is often sheared has been reinforced.
Reinforced type
LIFTING CAPACITY
PC78UU-6
6.0m
19'
5.0m
16'
4.0m
13'
3.0m
9'
2.0m
6'
1.0m
3'
0.0m
0'
-1m
-3'
-2.0m
-6'
-3.0m
-9'
*Load is limited by hydraulic capacity rather than tipping. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
STANDARD EQUIPMENT
• Air cleaner, single element
• Cooling fan, suction type
• Rear view mirror, RH
• Window washer, front
• Rigid seat
• Seat belt
• Heater & Defroster
Arm : 1720mm 5'8" Bucket width : 650mm 25.6" Shoe width : 450mm 17.7" Blade on ground
Cf
*6430
*14170
*3640
*8030
*3690
*8130
1.5m 4'
Cs
*6430
*14170
*3640
*8030
*3690
*8130
3.0m 9' 4.5m 14' Maximum
Cf
*2590
*5710
*2750
*6060
*3200
*7050
*3750
*8260
*4060
*8950
*3970
*8760
*3550
*7840
*2760
*6100
Cs
2530
5590
2480
5480
2300
5070
2030
4490
1810
3990
1690
3740
1670
3680
1710
3770
Cf
*2350
*5190
*2490
*5490
*2580
*5700
*2540
*5600
*2250
*4970
OPTIONAL EQUIPMENT
• Ashtray
• Water separator
• One-touch decelerator
• Shoes,
--- 450mm 17.7" Triple grouser
• Blade
• Air cleaner, double element
• Suspension seat
• Air conditioner
• Sunvisor
3
Bucket Capacity
Width, without Sidecutter
Width, with Sidecutter
m
mm in
mm in
yd
Cs
1080
2380
1010
2230
940
2070
880
1950
860
1910
*2150
*4750
*1810
*3990
*1760
*3890
*1830
*4030
*1990
*4390
*2200
*4850
*2200
*4850
*2160
*4770
*2020
*4460
*1340
*2970
• Fire extinguisher
• Travel alarm
• Tool kit
• Shoes,
--- 450mm 17.7" Road-Liner
--- 450mm 17.7" Rubber
3
0.12
0.09
14
350
18
450
0.12
450
550
0.16
18
22
Cf
0.20
550
650
0.26
22
26
0.28
650
750
*2150
*4750
*1340
*2970
0.37
26
30
Unit : kg lb
Cs
1730
3810
1140
2530
890
1970
770
1700
720
1590
730
1620
830
1840
1110
2440
0.34
725
0.45
29
_
5
PC78UU-6
COMPACT HYDRAULIC EXCAVATOR
The track frame is
sloped so that dirt
will not be accumulate and can be
removed easily.
Larger opening reduces
fuel back splash.
Inclined track frame topLarge fuel filler with strainer
Water-resistant DT
connectors are used for
the parts which water will
be splashed over.
O-ring face seals having
high sealing performance
are used for the hydraulic
piping joints.
DT connector
Face seal
Engine hood can be
opened and closed
even in confined
areas
Air cleaner with easily
replaceable element
Aluminum oil cooler and
radiator are corrosion
resistant and easy to clean
One fuel system
inspection window
for fast and easy
maintenance
Smaller and longer lasting hydraulic
oil filter: Ecowhite element
Easy check of battery liquid level
Large and accessible toolbox
Work equipment greasing interval is
250h (100h for armtop only)
Control pattern
change valve(optional)
Wide-opening side
hood makes daily
inspection simpler
Main valve can be
easily inspected
Window washer tank is
easy to check and refill
Whether you are
comfortable with ISO or
SAE control patterns,
you can easily and
consciously change from
one to the other.
EASY
MAINTENANCE
EASY
MAINTENANCE
Waterproof seal
Waterproof seal
Waterproof seal
4
OPERATOR
ENVIRONMENT
OPERATOR
ENVIRONMENT
Upper-rail type sliding
door opens and closes
smoothly
Housing the wiper
motor has greatly
improved visibility
Low noise design cab
Standard equipment
Defroster Cup holder
Photo:Rigid seat
73dB(A)
Suspension seat
(optional)
The cab offers comfort and space to help the operator
become even more confident and productive. The
ergonomically designed features help reduce fatigue
and increase focus on the job at hand. The low noise
levels of the engine helps reduce fatigue and can make
the operator even more comfortable.
Comfortable operator’s cab Thin potentiometer adopted and built in Hydraulic hose built in
Ceiling window
Air conditioner
Large capacity air
conditioning system
combined with carefully
placed vents provide
optimum cool air flow.
Loading...