Page 1
1. Minimum supply pressures: 0.5bar(0.05MPa).
2. Recommended supply static pressures:
3bar(0.3MPa) on hot and cold water.
3. Supply pressure greater than 5bar(0.5MPa) : install
a pressure reducer.
4. Hot water temperatures, minimum: 50°C,
maximum:80°C.
5. Recommended hot water temperature: 65°C
(energy-saving).
6. Setting range, approximately: 20°C to 50°C.
7. Safety stop at: 40°C.
8. Pressure difference between hot and cold supply:
2bar(0.2MPa) maximun..
9. The highest environment temperature for handspray
& showerhead is 60°C. Please keep handspray,
showerhead and the shower arm away from heater, or
it may become damaged and cause injury to the user.
1.最小供水压力：0.5bar(0.05MPa)。
2.推荐冷热供水的静态压力：3bar(0.3MPa)。
3.如果供水压力大于5bar(0.5MPa)，安装减压阀。
4.热供水温度最低：50°C；最高：80°C。
5.推荐的热供水温度：65°C。
6.温度的设定基本范围为：20°C到50°C。
7.安全限位温度：40°C。
8.冷热供水压力差不大于2bar(0.2MPa)。
9.花洒最高使用环境温度：60°C。请特别注意花洒
同花洒连接的臂管必须远离加热器，否则可能损坏
花洒及其密封件，甚至对使用者造成伤害。
所有的资料是按最新出版的产品资料编写而成。科
勒公司保留任何时候不经通知即可改变产品特性、
包装或产品可供类型的权利
。
说明书包括重要的安装、保养及清洁方面的内容，
请把这些资料交给用户阅读。
BEFORE YOU BEGIN
All information is based on the latest product
information available at the time of publication.
Kohler Co. reserves the right to make changes in
product characteristics, packaging, or availability at
any time without notice.
Please leave these instructions for the consumer.
They contain important information.
72641T 挂墙式恒温浴缸花洒龙头
72643T 挂墙式恒温花洒龙头
安装之前
INSTALLATION INSTRUCTIONS
安装说明书
安装尺寸
ROUGH-IN DIMENSIONS
Wall-Mount Thermostatic
OPERATION CONDITION
使用环境
837392-D 1
837392-D 4
97~102
95~100
Ø59
G1/2˝
G1/2˝
G1/2˝
G1/2˝
G1/2˝
G1/2˝
72641T 72643T
Stop assembly
限位组件
Cartridge
温控阀
Stop pin
定位柱
Stop pin
定位柱
Notch
限位槽
Notch
限位槽
Cartridge
温控阀
Cartridge and stop assembly
阀体限位组件
Round mark
圆孔标识
Groove
凹槽
Fig.11
Fig.12
Fig.9 Fig.10
Fig.6
Fig.5
Fig.7 Fig.8
Fig.2
维护与保养
CARE AND MAINTENANCE
The filters(18) protecting the faucet
device may get obstructed and reduce
water flow. When this happens, unscrew
the bushes(20, left thread) by a
wrench(12mm) and take out the nuts(19),
filters(18) and the check valves(17) after
removing the faucet. Clean the filters by
soaking them in warm vinegar. Reinstall
them as the figure.(Note: Check valves
should reinstall as original orientation).
Very hard water can obstruct the filters
protecting the thermostatic cartridge and
reduce the flow of water. Please clean
the cartridge as follows: Shut off the
water supply of the faucet and open the
water flow handle, then proceed to
remove the cartridge. The cartridge is
sensable, please be careful.
Make sure the reference mark is aligned
with number 37 before your action.
Remove the handle kit(Fig.7), unscrew
the nut and stopper(Fig.8). Removing the
cartridge cautiously(Fig.9). Clean the
thermostatic cartridge by soaking it in
warm vinegar. After cleaning, install the
‘stop assembly’ back on the cartridge,
adjusting the stop pin into the notch
(Fig.10). Install the assembly cartridge
and stop in the body, adjusting the stop
pin into the notch(Fig.11).
滤网垫片(18)可起到保护龙头的作用，
但长时间使用后水垢或杂质可能会堵
塞滤网降低水流量。如有类似情况发
生，卸下龙头，用六角扳手(12mm)将
底座(20,顺时针)拧下，取下螺母(19)、
滤网垫片(18)和单向阀(17)。用热醋清
洗滤网。然后按照图示装回。(注意：
单向阀必须按原方向装回)
。
如果供水的水质较硬或长时间使用，
水垢或杂质会阻塞温控阀上的滤网，
流量会降低。需要清理请按照下列步
骤进行：关闭供水系统，使流量阀处
于打开位置后进行温控阀拆卸作业。
温控阀是较敏感的配件，所以要十分
小心。
拆卸前确保指示标识与数字37对齐。
拆卸把手组件(Fig.7),然后将螺母和塑
料套卸下(Fig.8)。小心地卸下温控阀
(Fig.9)。用热醋进行清洗。清洗后，将
塑料套和螺母(限位组件)装到温控阀上
面，使塑料套的定位柱嵌入温控阀的
限位槽内(Fig.10)。然后将塑料套的定
位柱与龙头本体内孔凹槽对齐，装入
温控阀并锁紧螺母(Fig.11)。
18
17
19
20
星珀
YMBOL
温度测试与调整
在温度测试前，应确保供水系统充分
且有较高的温度。温控把手在37度位
置时，打开龙头让水流出。进行温度
测量，出厂时温度设定在36~38度范围
内。如超出这个范围，要进行调整。
调整的步骤如下：
取下把手上盖，用螺丝刀取下螺钉和
温控把手组件。在正常水流状态下，
由冷水位置开始慢慢转动温控阀轴(保
持同一方向)直至获得37度的水流。如
果温度超过38度，回到冷水位置重新
调整。
温度稳定后，不要转动温控阀轴，安
装温控把手，使温控把手的参考标识
与数字37对齐。锁紧螺钉，安装把手
上盖(图Fig.5)。
Verification and Setting
Make sure that the water feeds of the
faucet have reached their highest
temperature by letting the water run
sufficiently. With the selector in position
37ºC, the temperature of the water
coming out of the faucet must be within a
range of 36ºC and 38ºC, as measured by
a bath thermometer. If this is not the
case, the installer can adjust the setting.
Proceed with the setting as follows:
Uninstall handle kit. With the faucet on
‘cold’ normal water flow, slowly turn the
temperature selector(always in the same
direction) until water at 37ºC is obtained.
If the temperature goes over 38ºC, go
back to the ‘cold’ setting and set again.
When the temperature is stabilized,
without turning the cartridge spindle,
make sure the reference mark of the
temperature handle aligned with the
number37. Tighten the screw,put on the
handle plug. See fig.5.
Spindle
阀轴
Reference mark
参考标识
Number 37
数字37
Ø122
236
205
39°
150±15
1500
Ø59
52
150±15
G1/2˝
G1/2˝
20 Max.
20 Max.
49
40º
27
60
58
Page 2
837392-D 2
安装步骤
INSTALLATION
安装结果检查
INSTALLATION CHECKOUT
OPERATION INSTRUCTIONS
How to Install the Faucet
To perform installation, installer must
provide G1/2˝ female supply fittings,
spaced 150mm apart, horizontally and
not extending beyond the finished wall
surface. Hot supply pipe must be
located on the left.
Install the two offset connectors(1) into
the hot and cold supply pipes. Use
appropriate thread sealants or thread
tape on pipe threads.
Adjust the center-to-center distance
between the connectors to 150mm and
horizontally. They should extend 40 to
45mm beyond the finished wall. Thread
the escutcheon(2) onto the connectors
until they are against the finished wall.
Put washer(3) into nut(4) and tighten
the nut with tool(5).
When tighten the nut, use strap wrench
or soft cloth between product and
regular wrench to protect the finish.
Put the washer(6) between hose(8) and
shower outlet(9). Put the restrictor(7)
into the handspray(10) inlet. Provide
washer between the hose and
handpray. Tighten all the connections.
如何安装水龙头
为使安装顺利，G1/2˝内螺纹管道配件
应已安装好。预留150mm的间距，保
持水平，不要凸出墙面。热供水管装
在左边。
在两个接头(1)涂上螺纹密封膏或缠绕
足以密封的密封胶带，旋入冷热供水
管中。
调节两个接头，使其中心距为150mm
并保持同一水平。他们凸出墙面的尺
寸应该在40到45mm之间。将装饰罩
(2)旋入接头，紧贴墙壁。
将垫片(3)放入水龙头螺母(4)中，将螺
母旋到接头上，并用扳手(5)拧紧。
在锁紧螺母时，须用带状扳手或用软
布垫在普通扳手和螺母之间，以保护
镀层表面。
将垫片(6)安装在软管(8)与出水口(9)之
间。限流器(7)塞入手持花洒(10)进水
口 。 垫 片 安 装 在 手 持 花 洒 与 软 管 之
间。然后锁紧所有衔接螺母。
2
Hot
热
Cold
冷
837392-D 3
Bath & Shower Faucet
Remove the handspray and aerator by
tool(15). Turn the water flow handle to
the “open” position, and slowly turn the
temperature selector. Run water through
the faucet for about one minute to
remove any debris. Close the faucet, and
reinstall the handspray and aerator
assembly(16).
Shower Faucet
Remove the handspray. Turn the water
flow handle to the ‘open’ position, and
slowly turn the temperature selector. Run
water through the faucet for about one
minute to remove any debris. Close the
faucet, and reinstall the handspray.
浴缸花洒龙头：
取下手持花洒，用工具(15)卸下起泡器
组件。将流量把手旋转到开的位置，
慢慢旋转温控把手。让水流出约一分
钟，以清除杂质。关闭龙头，并装回
手持花洒和起泡器组件(16)。
花洒龙头：
取下手持花洒，打开水流把手，慢慢
旋转温控把手。让水流出约一分钟，
以清除杂质。关闭龙头，并装回手持
花洒。
Ensure that all coupling nuts are tight
and the water flow handle is in the close
position. Turn on the main water supply,
and check for leaks. Repair as needed.
确保所有衔接螺母都已锁紧。确保把
手处于关闭的位置。开启主水源，检
查是否有漏水。如有漏水，修理之。
1
5
4
150mm
3
10
使用说明
慢慢旋转温控把手即右把手，调整温
度，安全限位温度为40度。如果想得
到更高的温度，按住按钮继续旋转。
水流量是通过左把手来控制的。左把
手设有一个节水限位。如果想得到更
大的水流，按住按钮继续旋转即可。
节水限位器的调整
如果节水限位的水流不满足需要，可
进行调整(Fig.4)。取下把手上盖，用
螺丝刀取下螺钉及把手组件。调整限
位器限位点的位置。如果要得到更大
的限位水流，逆时针调整限位点；如
果想得到较小的限位水流，顺时针调
整限位点即可。
注意：
装回流量把手时，先使流量阀
处于关闭位置，并且将按钮与本体另
一端的数字37对齐，装回把手，拧紧
螺钉，安装把手上盖。
The temperature is set by slowly turning
the temperature selector(right-hand
handle). For safety reasons, there is a
stop that limits temperature to 40ºC. To
get a higher temperature, push the button
and continue turning the temperature
selector.
Water flow is set by turning the left-hand
handle. There is also a water-saving
stop. To obtain a higher flow rate, push
the button and continue turning it.
Stopper Adjustment
If the flow can't meet the demand, it can
be adjusted(Fig.4). Uninstall the handle
kit and adjust the position of stopper.
Turn the counter-clockwise to increase
the flow rate; Turn clockwise to decrease
the flow rate.
NOTE: When you reinstall the handle,
make sure the flow valve in the ‘close’
position, the button of water flow handle
should be aligned with the 37 mark.
Tighten the screw. Put on the handle
plug.
Stopper
限位器
Stopper
限位器
Plant setting position
出厂时限位点的位置
Increase the flow
增大水流
Decrease the flow
减小水流
40~45mm
Fig.1
Fig.2
Fig.4
Fig.3
7
6
9
8
6
How to Install the Bracket
Determine a suitable location on the
finished wall to install the bracket. Mark
bracket base mounting hole locations
on the wall according to the dimension.
Drill two holes on the finished wall, the
holes should match the anchors(11).
Install the anchors.
Tighten screws(12) to secure bracket
base(13, flat side upward). Put the
bracket(14) onto the bracket base and
lock by stopper.
如何安装托架
在墙面选一合适的位置来安装托架。
根据孔距在墙面标记钻孔的位置，依
据胀塞(11)直径打孔，安装胀塞。
旋紧螺钉(12)，使底座(13，平面朝上)
固定紧贴墙壁。将托架(14)扣在 底座
上，使凸台嵌入豁口。
27
12
14
13
11
KOHLER
15
16
Page 3
837392-D 5
清洗说明
CLEANING INSTRUCTIONS
适用于所有加工处理过的表面：以中性肥皂水清洗
镀层表面，再以干净的软布彻底擦干整个表面，许
多清洁剂，比如氨水、去污粉及洁厕灵等，会对电
镀表面造成伤害，切忌使用。
有磨损性的清洁用具或清洁剂也不可使用于科勒牌
的水龙头及其配件上。
All Finishes: Clean the finish with mild soap and warm
water. Wipe entire surface completely dry with clean
soft cloth. Many cleaners may contain chemicals, such
as ammonia, chlorine, toilet cleaner etc. which could
adversely affect the finish and are not recommended
for cleaning.
Do not use abrasive cleaners or solvents on Kohler
faucets and fittings.
NOTE: Do not turn the cartridge when
reinstall it. If you turned it without
carefully, you should adjust it and be
sure that the round mark is correctly in
line with the groove(Fig.12), or readjust
as per the steps of verification and
setting.
Install the temperature selector(without
turning the spindle). Align the reference
number 37 mark on the temperature
handle with the round laser mark on the
body(Fig.13). Tighten the handle with
the screw. Put on the handle plug.
注意：确保拆卸、安装过程中，不要
转动温控阀轴。如果不小心转动了阀
轴，要调整阀轴使外齿上的圆孔标识
与相邻的塑套上的凹槽对齐(Fig.12)，
或按前述方法调整。
安装温控把手,使温控把手的数字37标
识与本体圆形激光标识对齐，拧紧螺
钉。安装把手上盖。(Fig.13)
Number 37
数字37
Reference mark
参考标识
Temperature selector
温控把手
Spindle
阀轴
Page 4
**订购时请说明颜色编号
**Color code must be specified when ordering
SERVICE PARTS
零 件 图
Wall-Mount Thermostatic
837392-D 6
72641T 挂墙式恒温浴缸花洒龙头
72643T 挂墙式恒温花洒龙头
835239
Valve
温控阀
831727**
Hose Assembly
软管组件
880010
Washer
垫片
1065970**
Handspray
花洒
1030624
Restrictor
限流器
星珀
YMBOL
1170944**
Connection
连接件
865225**
Nut
螺母
1216770**
Spray Bracket
花洒托架
870992
O-ring
O型圈
837058
Aeartor
起泡器
(仅用于72641T)
865227**
Aeartor Cage
起泡器套
(仅用于72641T)
837224
Key
工具
(仅用于72641T)
870721
O-ring
O型圈
(仅用于72643T)
831752
Check Valve
单向阀
865224**
Escutcheon
装饰盖
1218659
Washer
垫片
832940
Washer
垫片
837192
Screw
螺钉
837192
Screw
螺钉
871612**
Handle Plug
把手上盖
836586
Filter Washer
滤网垫片
1219517**
Diverter Assy
切换器组件
(仅用于72641T)
865150
Nut
螺母
833405
Valve
流量阀
871584
Stopper
止水器
871585
Stop Assy
止水组件
832940
Washer
垫片
871625
Gasket
垫片
(仅用于72641T)
3021191
Seat
底座
864922**
Bush
接头
(仅用于72643T)
898779**
Flow Handle Assy
流量把手
898778**
Temperature
Handle
温控把手
871612**
Handle Plug
把手上盖
3019692
Circlip
档圈
Loading...