STILLNESS
®
Features
Brass construction
•
Available with blade handle
•
Push-button diverter
•
Includes showerhead with arm and flange
•
Codes/Standards Applicable
Specified model meets or exceeds the following:
ASME A112.18.1/CSA B125.1
•
Specified Model
BATH AND SHOWER FAUCET TRIM
K-T948
ALSO K-T949, K-T950, K-951, K-952
Colors/Finishes
CP: Polished Chrome
•
Other: Refer to Price Book for additional colors/finishes
•
Accessories
CP: Polished Chrome
•
Other: Refer to Price Book for additional colors/finishes
•
NA: None applicable
•
For complete faucet, both faucet trim and Rite-Temp®valve must be specified.
Model Description
K-T948-4 Bath and shower trim, blade handle ❑ CP ❑ Other_____
K-T949-4 Shower only trim, blade handle ❑ CP ❑ Other_____
K-T950-4 Valve only trim, blade handle ❑ CP ❑ Other_____
K-952 Bath spout ❑ CP ❑ Other_____
Required Accessories
K-304-* RiteTemp
K-2971-KS Rite-Temp valve OR ❑ NA
K-11748-K RiteTemp valve with diverter OR ❑ NA
valve OR ❑ NA
®
Product Specification
The Rite-Temp pressure-balancing single-control bath and shower faucet trim shall be made of brass construction. Bath and
shower trim shall include showerhead with arm and flange, and push-button diverter. Shower only trim shall include showerhead
with arm and flange. Faucet trim shall be K-T______-_____-_____ and Rite-Temp valve shall be K-____-______-NA.
Page 1 of 2
1031652-4-
C
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com
STILLNESS
Required Accessories
K-11748-KS RiteTemp valve with diverter and stops ❑ NA
* For a complete listing of all the RiteTemp valves, refer to the K-304-* Specification Sheet or Roughing-In Sheet.
Optional Accessories
88526 HiFlow Rite-Temp
1016154 Deep rough-in kit for Rite-Temp
®
thin wall installation kit ❑ CP ❑ Other_____
®
valve – lever or cross handle designs ❑ NA
®
Installation Notes
Install this product according to the installation guide.
NOTICE: Risk of product damage. Long screws, for
installing trim, can damage the K-2971-KS valve. Consult the
trim installation guide to verify if the thin wall installation kit
(88526) is needed.
Install this product according to the installation guide
Avoid cross-flow conditions. Do not install shut-off device on
either valve outlet.
Cap shower outlet if deck-mount spout, diverter, or
handshower is connected to spout outlet.
Install straight pipe or tube drop of 7″ (17.8 cm) to 18″
(45.7 cm) with single elbow between valve and wall-mount
spout.
1/2" - 14 NPT
2-1/2"
(6.4 cm) D.
6-5/16"
(16 cm) D.
1/2" - 14 NPT
30
7-7/8" (20 cm)
3/4" (1.9 cm)
2-7/8" (7.3 cm)
2-1/2"
(6.4 cm) D.
8-3/4"
(22.2 cm)
2-5/16"
(5.9 cm)
Top of Bath
6-3/8"
(16.2 cm) D.
10" (25.4 cm)
To Spout
(Bath Only)
5-1/2"
(14 cm) Min
72" (182.9 cm) 78" (198.1 cm)
To Floor
(Typical)
48" (121.9 cm)
To Floor
(Shower Only)
Product Diagram
STILLNESS®BATH AND SHOWER FAUCET TRIM
Page2of2
1031652-4-
C