Page 1
1204812-T01-B
-1-
INSTALLATION INSTRUCTIONS
VITREOUS CHINA FLOOR STANDING TOILET
K-9154T/K-9154T-S
PANACHE
·
·
·
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning, and
warranty information -.please leave instructions for the
consumer
·
·
·
-
NOTES
·
·
·
·
·
·
·
Observe all local plumbing and building codes.
Shut off the water supply.
51mm (2") passageway.
Ensure that the new drain has the correct roughing-in
dimension.
Carefully inspect the new fixture for any sign of damage.
For new construction, refer to the dimensions in
for locating the shut-off valve.
Fig. #1
Fixture dimensions are nominal and conform to tolerances
established by ASME Standards (A112.19.2-2013).
The product complies with GB 6952-2015.·
·
·
·
·
·
·
·
51mm
1
ASME (A112.19.2-
2013)
GB 6952-2015·
ORDERING INFORMATION
PANACHE Floor Standing Toilet ................................K-9154T
Includes PANACHE Bowl .....................................K-18154A
Includes ..............................K-4760T
Includes .......................................................1036901
PANACHE Floor Standing Toilet .............................K-9154T-S
Includes PANACHE Bowl .....................................K-18154A
Includes ........K-17674T
Includes .......................................................1036901
Can match with K-6286T in-wall tank .
PANACHE Toilet Seat
P-Trap
PANACHE Quiet-close Toilet Seat
P-Trap
®
®
...................................................K-9154T
.........................................................K-18154A
.........................................K-4760T
.......................................................1036901
................................................K-9154T-S
..........................................................K-18154A
................................K-17674T
........................................................1036901
K-6286T
No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 528137
2 528137
8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA POST CODE: 256410
8 256410
©©Copyright Kohler China Investment Co., Ltd. 2015
2015
Page 2
1204812-T01-B
WARNING: Risk of personal injury or product
damage
WARNING: Risk of external leakage
: Handle vitreous china products very carefully.
Vitreous china can break and chip if you overtighten
bolts and nuts.
. The fill valve
nut has been factory-tightened to design specifications.
If re-tightening is required, wrench tighten one turn
past finger tight .
-2-
TOOLS AND MATERIALS REQUIRED (NOT
SUPPLIED)
·
·
·
·
·
·
·
·
·
254mm (10") adjustable wrench
305mm (12") pipe wrench
Tape measure
Level
Drill (10mm. Drill bit)
Screwdriver
Plastic connector (Supplied)
Toilet installation bolt (Supplied)
S-TRAP 1206391(Optional)/P-TRAP 1036901 (Supplied)
·
·
·
·
·
·
·
·
·
254
305
( 10mm)
()
()
S 1206391( )/P 1036901( )
ROUGHING-IN
Fig.#1
1
Kohler reserves the right to change marked dimensions without prior notice.
Finished Wall
Finished Wall
Finished Wall
Finished Wall
Reference Value
UNIT: mm
1036901
P-Trap
1206391
S-Trap(Optional)
()
185
90-110
550
C
C
L of Inlet
Inlet
L of Outlet
Outlet
380
352
185
85
215
358
350
155
Floor Fixings
55
102
Page 3
1204812-T01-B
1.
2.
3. 10mm
4.
5.
6.
7.
Back edge of pan
Back edge of pan
Wall
Installation template
Fig.#3
3
-3-
1. Put the bowl in position and mark a line along the back of
the bowl.
2. Place the template on the floor, align to the pencil line and
secure to the floor.
3. Drill the fixing holes with a 10 mm drill as indicated on the
template.
4. Fit the clamps to the floor with the floor plugs, washers and
nuts.
5. Position the bowl and install the soil pipe in accordance
with the manufacturer s instructions.
An inlet isolating valve must be installed to the bowl.
6. Connect the inlet water supply to the bowl.
7. Secure the bowl in positon with the plastic sleeve and the
screw. Fit the plastic cover cap.
Note!
,
Cover Cap
Screw
Plastic Sleeve
Fixing Hole
Bolt
Washer
Clamp
Floor plug
Fig.#4
4
Fig.#5
5
INSTALL THE BOWL
Page 4
1204812-T01-B
()
0C
o
CONSUMER RESPONSIBILITIES
If you live in a hard water area, make certain that the holes in
the toilet rim are kept clean to ensure proper bowl flushing.
Toilet bowl cleaners should be used at least once a week.
Use a long-handled brush to clean the rim holes, and to clean
as far into the trap as possible to prevent mineral deposits
from forming.
Most toilet bowl cleaners are not harmful to the vitreous china
surface of the toilet bowl. Please follow the bowl cleaner
manufacturer's instructions carefully.
Do not use abrasive cleaners or solvents.
Do not use in-tank cleaners. Products containing
chlorine (calcium hypochlorite) can seriously damage
fittings in the tank. This damage can cause leakage
and property damage.
Kohler Company shall not be responsible or liable for any
damage to these tank fittings caused by the use of cleaners
containing chlorine (calcium hypochlorite).
WARNING: Risk of property or product damage.
WARNING: Risk of product damage.
CAUTION:
Do not throw into the toilet what is easy to block it,
such as newspaper, paper pilch, sanitary towel.
Do not bump the vitreous china with great force to
prevent it from damaging and leaking.
Do not use the toilet in the water below 0 C.
Please do not use hard materials (like
scouring pad) to clean product surface, especially the
product logo.
o
-4-
Loading...