KOHLER K-77686 Installation Manual

Installation and Care Guide

Water Filtration System

Français, page ″Français-1” Español, página ″Español-1”

1285422-2-C

Tools and Materials

Permanent Marker

Plus:

3/8" Cold Water Supply

• Fasteners (filter head to cabinet)

• Common woodworking tools

Before You Begin

WARNING: Risk of personal injury. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

CAUTION: Risk of property damage. Do not install the unit where the temperature may drop below freezing, may be exposed to direct sunlight, or may be exposed to heat.

NOTICE: Read this entire manual thoroughly to prevent personal injury and property damage during installation and use of this product.

NOTICE: Check with your local public works department for plumbing code requirements. Follow their guidelines as you install this water ﬁltration system.

NOTICE: This product has a limited service life. Keep a record of the date of installation and any other performed maintenance. Because of the limited service life, and to prevent costly repairs or possible water damage, replace the system every 10 years.

NOTICE: Turn off the water supply to the ﬁlter head, and remove the ﬁlter cartridge if it will be unattended for an extended period of time (approximately 4 weeks or more). Store the ﬁlter cartridge in a sealed bag in the refrigerator to maximize the remaining ﬁlter capacity.

NOTE: Make sure that the mounting location and fastening hardware will support the system when installed and full of water.

1285422-2-C 2 Kohler Co.

Before You Begin (cont.)

Observe all state and local plumbing and building codes. Contaminants or other substances removed or reduced by this

ﬁltration system may not be present in your water. Refer to the Performance Data Sheet (included) for contaminants and reduction performance.

Inspect the plumbing and supplies for damage. Repair or replace as needed.

Install the water ﬁltration system to a cold water supply only. Do not install the system to a hot water supply.

The water ﬁltration system is designed to be installed beneath a sink. Make sure that the bottom of the ﬁlter cartridge is at least 2″ (51 mm) above the ﬂoor of the cabinet, and will be accessible for ﬁlter cartridge replacement after installation.

Replace the ﬁlter cartridges every 6 months, when the capacity has been exceeded, or when a noticeable decrease in water ﬂow is observed.

Flush the ﬁlter system thoroughly after prolonged periods of nonuse. Allow the water to ﬂow for 5 or 6 minutes before use.

This system connects to a 3/8″ (9/16″-24 UNEF-2A) compression connection. Special ﬁttings may need to be purchased to accommodate other connections.

Record your model number and installation date below. Also mark the installation date on the ﬁlter head and ﬁlter cartridges. Model number: ____________ Replacement date: _____________

Keep this manual for future reference.

To learn more about other KOHLER water ﬁltration systems, replacement cartridges, subscription services, and recycling program visit kohler.com.

Kohler Co. 3 1285422-2-C

Water Supply Adapter

Tee

Water Supply Adapter

1. Prepare the Site

For existing installations: Turn off the cold water supply, and turn on the faucet to relieve water pressure and drain water from the line.

Disconnect the cold water supply line from the cold water supply valve.

NOTICE: Use care to avoid overtightening or cross-threading the connections to prevent water leakage.

If both ﬁltered and unﬁltered water will be supplied, install the tee (provided) to the cold water supply valve.

Connect the water supply adapter to the cold water supply valve or the tee.

1285422-2-C 4 Kohler Co.

2" (51 mm) Min

2. Mount the Filter Head

IMPORTANT! This unit is designed for vertical installation.

IMPORTANT! The mounting location of the water ﬁltration system

is critical. Verify that the bottom of the ﬁlter cartridge will be at least 2″ (51 mm) from the ﬂoor of the cabinet. Ensure that the system will not interfere with other items and will be easily accessible. Make sure that the tubing will not be under tension when installed.

NOTICE: Select mounting fasteners (not provided) appropriate for the cabinet wall material.

Align the mounting holes of the ﬁlter head at the determined mounting location.

Mark the mounting-hole locations with a permanent marker. Set the ﬁlter head aside.

Predrill the mounting holes, if necessary, based upon the fasteners selected.

Partially thread the fasteners into the cabinet wall, and slide the ﬁlter head over the fasteners.

Secure the ﬁlter head in position by tightening the fasteners.

Kohler Co. 5 1285422-2-C

Unfiltered Water Faucet Supply

Cover

Inlet

Filtered Water Faucet Adapter

Outlet

3/8" Cold Water Supply

Water Supply Adapter

Use water to wet the tubing ends.

3. Connect the Tubing

CAUTION: Risk of property damage. Do not damage, kink, or crimp the tubing. Avoid cutting the tubing. If it is necessary to cut the tubing, use a sharp utility knife to make a clean and square cut to avoid water leakage.

IMPORTANT! Water from the supply line must be connected to the ﬁlter head inlet. Water from the ﬁlter head outlet must be connected to the faucet. System performance and ﬁlter capacity will be compromised if connected incorrectly.

Wet the end of one of the tubing sections with water, and press it ﬁrmly into the inlet port of the ﬁlter head.

Wet the other end of the tubing with water, and press it ﬁrmly into the water supply adapter.

Repeat for the other tubing section, pressing one end into the outlet port of the ﬁlter head. Press the remaining end into the ﬁltered water faucet adapter.

Connect the ﬁltered water faucet inlet to the ﬁltered water faucet adapter.

If used, connect the unﬁltered water faucet inlet to the tee. Press the cover onto the ﬁlter head. If desired, secure the tubing to a cabinet wall using appropriate

clamps and hardware (not provided).

1285422-2-C 6 Kohler Co.

O-Rings

Cap

Write the date on the label.

4. Install the Filter Cartridge

IMPORTANT! For the K-77686: Two identical ﬁlter cartridges are used. For future ﬁlter cartridge replacement, replace both cartridges at the same time to maintain proper performance.

Write the installation date on the new ﬁlter cartridge label. Remove and discard the cap from the ﬁlter cartridge. Inspect the ﬁlter cartridge for damage. Verify that both sets of O-rings are present and are positioned

correctly in the grooves.

NOTE: The ﬁlter cartridge will only engage into the ﬁlter head one way. Do not force the components.

Align the ﬁlter cartridge so the label is to the left, and press upward so the ﬁlter cartridge key engages into the ﬁlter head.

Use your hand to rotate the ﬁlter cartridge counterclockwise 90° until it stops and is securely engaged into the ﬁlter head.

5. Installation Checkout

Turn on the cold water supply and check all connections for leaks. Repair as needed.

Run water through the faucet for at least 5 minutes to remove any air and carbon particles in the system.

Kohler Co. 7 1285422-2-C

Maintenance

Routine maintenance and ﬁlter cartridge replacement will not require that the tubing be disconnected. Follow this procedure if it becomes necessary to disconnect the tubing from the ﬁttings.

•

Turn off the cold water supply to the ﬁltration system, and turn on the faucet to relieve water pressure.

•

Firmly press in the collar around the ﬁtting while using your hand to pull the tubing free.

•

Inspect the tubing for damage or crimping.

•

Refer to the ″Connect the Tubing″ section to reinstall the tubing.

•

Refer to the replacement ﬁlter cartridge installation instructions to replace the ﬁlter cartridge.

Troubleshooting

This troubleshooting guide is for general aid only. For warranty service, contact your dealer or wholesale distributor.

For service parts and replacement ﬁlter cartridges, visit your product page at kohler.com.

Symptoms Probable Causes Recommended Action

1. Water leaks

between the ﬁlter head and the ﬁlter cartridge.

A. An O-ring is

damaged, dirty, or out of place.

A. Turn off the water

supply, and relieve water pressure. Remove the ﬁlter cartridge and inspect the O-rings for damage or debris, and ensure that the O-rings are in place. Reinstall the ﬁlter cartridge, turn on the water supply, and check for water leakage.

1285422-2-C 8 Kohler Co.

Troubleshooting (cont.)

Symptoms Probable Causes Recommended Action

2. Water leaks at

a tubing connection.

A. Tubing is not cut

square, or is damaged or crimped.

A. Turn off the water

supply, and relieve water pressure. Press in the collar around the ﬁtting at the leak, and pull the tubing to remove. Use a sharp utility knife to cut 1/2″ (13 mm) off the end of the tubing. Reinsert the tubing into the ﬁtting. Turn on the water supply and check for leakage.

3. Water leaks at

a threaded connection.

A. The connection is

damaged or dirty.

A. Turn off the water

supply, and relieve water pressure. Disconnect the ﬁtting, and inspect the seal for damage or debris. Remove any debris or replace the damaged ﬁtting. Securely reconnect the ﬁtting, but do not overtighten. Turn on the water supply and check for leakage.

Kohler Co. 9 1285422-2-C

Kohler Aquifer® Filtration System Replacement Cartridges: K-77687 (1 Pack) & K-77688 (2 Pack)

Model Series: K-77685 Single Manifold System Flow Rate: 0.85 gpm (3.21 lpm) Capacity: 389 gal (1,472 L)

Model Series: K-77686 Double Manifold System Flow Rate: 1.70 gpm (6.43 lpm) Capacity: 778 gal (2,945 L)

The K-77685 and K-77686 models are tested and certified by IAPMO R&T Lab and IAPMO R&T against CSA B483.1; NSF/ANSI Standard 42 for the aesthetic reduction of chloramines and Particulate Class I; NSF/ANSI Standard 53 for the reduction of asbestos, cysts, lead, mercury, MTBE, turbidity and VOC; NSF/ANSI Standard 401 for the reduction of Phenytoin, Bisphenol A, Estrone, Ibuprofen, Naproxen, and Nonyl phenol; and NSF Protocol P473.

See Performance Data Sheet for individual contaminants and reduction performance.

These systems conform to NSF/ANSI 42, 53, and 401, and NSF Protocol P473 for the specific performance claims as certified and substantiated by test data.

The compounds certified under NSF/ANSI 401 have been deemed as emerging contaminants.

Speciﬁcations

For conditions of use and replacement parts, refer to this guide and the Performance Data Sheet.

Do not use on water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after this ﬁlter system. Systems certiﬁed for cyst reduction may be used on disinfected waters that may contain ﬁlterable cysts.

Operating Pressure: 40 psi (276 kPa) - 120 psi (827 kPa) Operating Temperature: 33°F (0.5°C) - 100° (37.8°C) Service parts and replacement cartridges are available from your

local distributor, or directly from Kohler Co.:

1285422-2-C 10 Kohler Co.

Speciﬁcations (cont.)

Kohler Co., 444 Highland Drive, Kohler, Wisconsin, 53044

Warranty

KOHLER®Water Filter Systems FIVE-YEAR LIMITED WARRANTY

KOHLER water ﬁlter systems (excluding the disposable replacement cartridges) used in the United States and Canada are warranted to be free of defects in material and workmanship for ﬁve (5) years from the date of purchase in normal residential use. (The service life of any disposable replacement cartridge varies with local water conditions and water consumption and thus is not warranted other than to be free of defects in material and workmanship at the time of purchase.)

All products must be installed and operated in accordance with the manufacturer’s recommended procedures and guidelines. Improper use or installation could void this warranty.

If a defect is found in normal residential usage in the United States or Canada, Kohler Co. will, at its election, repair or replace the unit, or make appropriate adjustment. Damage caused by accident, misuse, or abuse is not covered by this warranty. Kohler Co. is not responsible for labor charges, removal charges, installation, or other incidental or consequential costs. In no event shall the liability of Kohler Co. exceed the purchase price of the product. These water ﬁlter systems have not

been tested or certiﬁed to meet regulatory standards outside the United States and Canada. To the extent permitted by law, Kohler Co. hereby disclaims all warranties for water ﬁlter systems used outside of the United States or Canada whether express or implied, including but not limited to the implied warranties of merchantability and ﬁtness for a particular purpose.

To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home Center or E-tailer, or by writing Kohler Co., Attn: Customer Care Center, 444 Highland Drive, Kohler, WI 53044, USA, or by calling 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and 001-800-456-4537 from within Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from within Canada, or www.mx.kohler.com in Mexico.

KOHLER CO. AND/OR SELLER ARE PROVIDING THIS WARRANTY IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KOHLER CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do not allow

Kohler Co. 11 1285422-2-C

Warranty (cont.)

limitations on how long an implied warranty lasts or the exclusion or limitation of special, incidental, or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you speciﬁc legal rights. You may also have other rights which vary from state/province to state/province. This limited warranty provides speciﬁc legal rights as they apply within the USA. Other rights may be available, but may vary from country to country.

This is Kohler Co.’s exclusive written warranty.

1285422-2-C 12 Kohler Co.

Guide d’installation et d’entretien

Système de ﬁltration d’eau

Outils et matériel

Plus:

Alimentation en eau froide 3/8"

Avant de commencer

AVERTISSEMENT: Risque de blessures. Ne pas utiliser avec de l’eau qui n’est pas sûre au point de vue microbiologique ou d’une qualité non connue sans désinfection adéquate avant ou après le système.

• Dispositifs de fixation (tête de filtre sur meuble)

• Outils de menuiserie habituels

Marqueur permanent

ATTENTION: Risque de dommages matériels. Ne pas installer ce dispositif dans des endroits où la température pourrait descendre au-dessous du niveau de congélation, où il pourrait être exposé à la lumière directe du soleil, ou encore à la chaleur.

AVIS: Lire ce manuel au complet aﬁn de prévenir des lésions corporelles et des dommages matériels au cours de l’installation et de l’utilisation de ce produit.

AVIS: Vériﬁer les exigences de codes de plomberie auprès du département de travaux publics local. Suivre leurs directives lors de l’installation de ce système de ﬁltration d’eau.

AVIS: Ce produit a une durée de vie utile limitée. Conserver un dossier indiquant la date d’installation et tout autre entretien

Kohler Co. Français-1 1285422-2-C

Avant de commencer (cont.)

exécuté. En raison de la durée de vie utile limitée, et pour empêcher des réparations coûteuses ou des dégâts d’eau éventuels, remplacer le système tous les 10 ans.

AVIS: Couper l’alimentation en eau à la tête du ﬁltre et retirer la cartouche du ﬁltre si on ne s’en occupe pas sur une période prolongée (4 semaines environ ou plus) Entreposer la cartouche du ﬁltre dans un sac scellé dans le réfrigérateur aﬁn de porter au maximum la durée de vie restante du ﬁltre.

REMARQUE: S’assurer que l’emplacement de montage et la visserie de ﬁxation pourront supporter le système lorsque celui-ci est installé et rempli d’eau.

Respecter tous les codes de plomberie et de bâtiment de l’État et locaux.

Les contaminants ou d’autres substances retirées ou réduites par ce système de ﬁltration pourraient ne pas être présents dans votre eau. Consulter la ﬁche technique sur la performance (incluse) en ce qui concerne les contaminants et la performance de réduction.

Inspecter la plomberie et les accessoires pour y rechercher des dommages éventuels. Réparer ou remplacer selon les besoins.

Installer le système de ﬁltration d’eau sur une alimentation en eau froide seulement. Ne pas installer ce système sur une alimentation en eau chaude.

Le système de ﬁltration d’eau est destiné à être installé au-dessous d’un évier. S’assurer que le fond de la cartouche du ﬁltre se trouveà2po(51mm)aumoins au-dessus du plancher du meuble et qu’il sera accessible pour le remplacement de la cartouche du ﬁltre après installation.

Remplacer les cartouches de ﬁltre tous les 6 mois, lorsque la capacité a été dépassée, ou lorsque l’on observe une réduction perceptible dans le débit d’eau.

Purger le système du ﬁltre au complet après des périodes prolongées de non utilisation. Laisser l’eau s’écouler pendant 5 ou 6 minutes avant utilisation.

Ce système se connecte à un connecteur de compression de 3/8 po (9/16 po-24 UNEF-2A). Il sera peut-être nécessaire d’acheter des raccords spéciaux pour s’adapter à d’autres connexions.

1285422-2-C Français-2 Kohler Co.

+ 30 hidden pages