Page 1
SERVICE PARTS
944-4 WALL-MOUNT DUAL HANDLE BASIN FAUCET
870721
O-ring
34263
O-ring
1006375
Flange
3005397
Outlet Bushing
1006374
Sleeve
1008179
Screw
Wall-Mount Dual Handle Basin Faucet
1119280(Right)
1119281(Left)
Valve
1127028
Bush
1119983
Stem Extension
1127029
Nut
1060271
Washer
1074608-H**(Left)
1074608-C**(Right)
Lever Handle Kit
1060271
Washer
870721
O-ring
1006718**
Escutcheon
INSTALLATION INSTRUCTIONS
Wall-Mount Dual Handle Basin Faucet
944-4 WALL-MOUNT DUAL HANDLE BASIN FAUCET
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co.
reserves the right to make changes in product characteristics, packaging, or availability at any time without
notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove any debris.
2. Inspect the supply tubing for damage. Replace as necessary.
3. Observe all local plumbing codes.
4. Check for leaks before covering the pipes, repairs as needed.
OPERATION INSTRUCTION
Both handles open with turning upwards, close with turning downwards.
ROUGH-IN DIMENSIONS
252
200
50~70
108~128
42
。
60
1094696**
Spout Kit
94786
Hex Wrench
1060037**
Aerator Kit
**Color code must be specified when ordering
1126071-2A/Rev00 4
48
50
48
58
48
68
1126071-2A/Rev00 1
Page 2
INSTALLATION
INSTALLATION CHECKOUT
Ensure that all connections are tightened. Ensure that the handles are
in the off position.
1
Open the drain. Turn on the main water supply and check for leaks.
Repair as required.
3
How To Install The Handle Kits
Remove and discard the guards after completed the finished wall.
Rehearse the handle kit(4) installation for cutting the length of the
stem extension(5) determination. Place the stem extension on the
valve making sure that the internal spline has correctly engaged the
valve, and the external spline has correctly engaged the handle kit.
Measure the length from the bottom of the escutcheon(6) to the
finished wall. Remove the handle kit and stem extension. Mark the
nearest stem extension groove according to the length. Cut through
the marked stem extension groove.
Install the sticker washers(7) into the groove on the bottom of the
escutcheons. Screw the nuts(8) onto the escutcheons. Press the stem
extensions onto the valve stems. Screw and hand tight the handle kits
(The handle kit with the red washer on the left when facing the front of
the faucet) until the escutcheon against the finished wall.
2
50~70mm
Remove the aerator assembly(15). Turn the faucet handles on and
run the hot and cold water through the spout for about one minute to
15
remove any debris. Remove debris from the aerator assembly. Shut
off water supply and reinstall the aerator assembly.
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with a clean
soft cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could
adversely affect the finish and are not recommended for cleaning.
8
5
7
6
4
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
The configuration shown is the correct position of the handle kits in
the closed position.
How To Install The Spout Kit
Remove and discard the guard(9) from the spout kit(10).
11
Thread the spout kit onto the spout connector(11). Unscrew the spout
kit properly to make sure it adown. Adjust the flange(12), tighten the
screws(13) by hex wrench(14) to secure the spout kit. Push the
escutcheon kit(14) against the wall and ensure the mark of “KOHLER”
upward.
1126071-2A/Rev00 2
13
14
9
12
10
1126071-2A/Rev00 3
Loading...