Page 1
All information is based on the latest product information available at the time of publication. Kohler Co.
reserves the right to make changes in product characteristics, packaging, or availability at any time without
notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove any debris.
2. An in line water filter must be used with this product.
3. Inspect the supply pipes for damage. Replace as necessary.
4. Observe local plumbing codes.
5. Check for leaks before covering the pipes. Repair as needed.
6. Recommended working pressure: 100KPa to 500KPa.
7. Maximum working pressure: 800KPa.
8. All installations should comply with the relevant requirements of AS/NZS 3500.
9. Inlet threads of the body are Rc 1/2.
1161638-AN2-B 28/04/16
Bath Mixer: 9122A-4-CP
BEFORE YOU BEGIN
INSTALLATION INSTRUCTIONS
ROUGH-IN DIMENSIONS
Wall Mount Single Lever Mixer
STANCE
BATH TAPWARE
1
SPARE PARTS
**Color code must be specified when ordering
1161638-AN2-B 28/04/16
4
Wall Mount Single Lever Mixer
STANCE
BATH TAPWARE
Bath Mixer: 9122A-4-CP
34263
O-ring
1141837
Mountin
g
Plat
e
30083
47*
*
Scre
w
83
4
638
Hex Wren
ch
1132
90
4
W
as
h
er
1133016-A*
*
Faceplate
83275
1
Screw
1
132905
Was
h
e
r
83373
0
H
e
x Wr
e
n
ch
10
4
6
2
90
H
ex Wrench
3007001
O-ring
880084
O-ring
3002868
Washer
1142493
Aerator
Key
Aerator
880085
O-ring
834460
Valve
1032559
O-ring
3006328**
Nut
1133013**
Bonnet
1130088**
Handle
8
80002**
Pl
ug
B
utton Kit
Scre
w
1002015
1
1421
0
2*
*
Aerator
Housing
1179019**
Aerator
Kit
1071996
Mounting Plate
1081338
Screw
841252
Washer
12º
213
48-58
230
83.5
102
125
42
114
RC 1/2
Hot
RC 1/2
Cold
Page 2
Note: During installation the protectors are to remain on the valve body.
1.) Construct a suitable wall frame for the mounting plate(1). Make sure
that the frame is level and allows for the correct valve rough-in per
the rough-in section on page1.
2.) Fix the mounting plate to the valve body(2) with the washers(3) and
the three xing screws(4). Be sure the protectors(5,6) face front and
the inlet with the red mark is on the left.
3.) The outer surface of the nished wall should be between the MAX &
MIN marks on the protectors(6) shown in Fig.1 and Fig.2.
The size of the opening in the nished wall is as shown in Fig.2.
4.) Fix the mounting plate and valve body to the wall frame.
Note: Ensure the centreline of the valve is perpendicular to the wall.
Make sure that the valve body is securely fastened to the wall frame.
5.) Connect Rc1/2” hot and cold supplies to the valve inlets shown in
Fig.1. Connect the hot supply to the left inlet with the red mark.
INSTALLATION - Valve Body
1.) Remove the protectors after the wall is nished.
2) Tighten the screws(7) with 3mm hex wrench(8) to secure the
mounting plate(9) until it is against the wall.
3) Loosen screws(10) on the faceplate kit(11) with 2mm hex
wrench(12).
4) Slide the faceplate kit onto the connector(13) and bonnet(14)
until it is against the wall. Tighten screws(10) to secure the
faceplate kit.
Note: Be careful not to damage the o-ring(15) on the
connector(13).
5) Slide the washer(16) into the groove on the faceplate kit.
Loosen the screw(17) on the spout(18) with 2mm hex
wrench(12).
6) Slide the spout onto the connector with its outlet downwards.
Tighten the screw(17) to secure the spout.
8) Close the valve and loosen the screw(19) on the handle with
2.5mm hex wrench(20). Install the handle(21) onto the valve
body. Tilt it upwards and tighten the screw.
9) Press the plug button(22) into the hole and close the valve.
INSTALLATION - Handle and Spout
1161638-AN2-B 28/04/16
2
1
2
Fig.2
Fig.1
8
7
9
12
11
10
13
15
14
16
18
20
21
19
22
68
171
3
4
5
6
6
Hot
Cold
Fig.3
Finished wall
Finished wall
17
1.) Ensure that all coupling nuts are fastened securely.
2.) Ensure that the handle is in the o position.
3.) Open the drain and turn on the main water supply and check for
leaks. Repair as needed.
4.) Remove the aerator kit (23) using the key(24).
5.) Turn the tap on and ush hot and cold water through the spout
for about one minute to remove any debris. Re-check for leaks
at this time.
6.) Remove any debris from the aerator.
7.) Turn the tap o and reinstall the aerator kit.
INSTALLATION CHECK
CLEANING INSTRUCTIONS
All Finishes: Clean the nish with mild soap and warm water. Wipe entire surface completely dry with a
clean soft cloth. Many cleaners may contain such chemicals as ammonia, chlorine, toilet chemicals etc. which
could adversely aect the nish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler ttings.
1161638-AN2-B 28/04/16
3
Finished wall
23
24
Loading...