Kodak X-Omat 460, X-Omat M6RA, X-Omat M7B, X-Omat M8, X-Omat M20 User manual

Publication

Supersedes

No.

261910

1/94

261910

1/91

for

INSTALLATION

SEISMIC

the

Kodak

Kodak

M20,

M6

M35

RP

Family,

X-Omat

Family,

M35/M43/Clinic 1 STAND

BRACKET

X-Omat

M7

INSTRUCTIONS

for

Kit

PROCESSORS

Family,

M8;

PROCESSORS

460

RA,

480

use

RA;

on

©

Eastman

Kodak

Company,

1994

The
Eastman

No

Eastman
or
special
other

information

Kodak

patent

license

Kodak

implied,

with

damages,

fault.

contained

Company

is

granted

Company

respect

to

resulting

herein

is

prior

to

publication.

by

this

reserves

this

information.

from

the

based

on

the

information.

the

right

to

change

Kodak

use

of

this

information,

PLEASE

experience

this

shall

not

be

NOTE

and

knowledge

information

liable

if

for

loss

even

relating

without

any

loss

or

damage

to

notice,

or

damage,
is

caused

the

and

subject

makes

including

by

Kodak's

matter

gained

no

warranty,

consequential

negligence

by

express

or
or

The

kit,

Part

No.

261413

includes:

Part

No.

240104
261898
261929

188623
173824

261910

Parts

Description

BRACKET
FLOOR

ANCHOR

BOLT - Stainless

WASHER - Stainless

Installation

CUP

Instructions

List

Steel

Steel

Quantity

20002

261910

To

[1]
[2]

[3]

[4]
[5]

install

Move
Install

STAND.
Level

The

2.5

Install

Align

PROCESSOR

the

BRACKET:

the

PROCESSOR

the 4 FLOOR

Align

the

PROCESSOR

maximum

cm

(1

in.).

the 4 SEISMIC

the

edge

CUPS

the

flat

side

clearance

BRACKETS

of

each

STAND.

or

the

under
of

each

or

the

between

SEISMIC

PROCESSOR

the 4 LEVELING

FLOOR

PROCESSOR

the

PROCESSOR

with

the

BRACKET

STAND

CUP

STAND

NOTE

SLOTS

with

SCREWS

so

that

over

the

to

its

it

by

adjusting

or

the

the

side,

permanent

on

the

is

toward

PROCESSOR

LEVELING

front,

or

|

position.

PROCESSOR

the

SEISMIC

the

LEVELING

SCREWS.

back

of

STAND

the

PROCESSOR

|

or

the

BRACKET.
SCREWS.

and

PROCESSOR

the

floor

or

is

the

[6]

[7]
[8]

[9]
[10]
[11]

Make a mark

Remove
Insert
Insert a PUNCH
Hit
Install

the

SEISMIC

the 8 ANCHORS

the

PUNCH

the 4 SEISMIC

on

the

or

or

floor

through

BRACKETS

in

the

NAIL

into

NAIL

with a HAMMER.

BRACKETS

holes.

the

개

each

hole

and

drill

Be

sure

ANCHORS.

with

the 8 BOLTS

LEVELING
SCREW

in

the

holes

that

(4)

SEISMIC

in

the

the

and 8 WASHERS.

LEVELING

FLOOR

BRACKETS.

floor.

ANCHORS

SCREW

WASHER

PLATE

Make

are

(4)

(8)

(4)

the

flush

holes

with

9.5 x 25
the

floor.

BOLT

(8)

mm

(% x 1

in.).

3229ii_j.txt

261910

ES

BRACKET

し

<5

©

(4)

Kodak

and

X-Omat

are

trademarks.

Printed

in

USA

EASTMAN

KODAK

COMPANY

Health

ㆍ

ROCHESTER,

Sciences

Division

N.Y.

14650