Kodak V600 User Manual
V600 Digital Projector
V600 Zoom Digital Projector
with Kodak’s Exclusive Image Manager
Connecting the Projector
The cables are color coded to assist you with making
the connections.
When you connect the power cable to the projector, the
Power light on the keypad begins to blink slowly.
You can connect more than one image source at a time.
If you are using an older MACINTOSH computer, you
might need to use the MACINTOSH adapter that was
included with your projector.
PC / MAC
S-VIDEO VIDEO AUDIO
AC
110V
220V
PC/MAC connection
to the computer monitor port
S-Video
to the S-Video Out port
Audio
to the source’s Audio out port
Video
to the Composite video out port
~
Power cord connection
to an electrical outlet
Warning: Turn off the image source and projector before
connecting or disconnecting cables.
Power
Menu
Power
Button
Keypad
POWER
Starting the Presentation
Enter
Adjust
Volume
Next
Remote
Control
(Optional
with V600)
MENU
ADJUST
ENTER
NEXT
Foot Release
Buttons
1. Connect the signal cable to the computer or video source.
2. Connect the power cord to the projector and to a power
source.
The power light begins to slowly blink green.
3. Turn on the presentation components in the order listed:
• Video source such as VCR, DVD or digital camera
• Audio source if different from your video source or
computer
• Projector – press the Power button on either the
remote control or the keypad
• Computer
4. Position the projector by using the adjustable feet on the
bottom of the projector.
5. Turn the focus ring to focus the image and turn the zoom ring (V600 Zoom model only) to zoom in or out on the
image.
6. Make any necessary image adjustments by using the on-screen menus. Press the Menu button to view the menu choices.
Use the Adjust + – buttons to go to the desired tab. Press the Menu button again to dismiss the menus.
7. Run your presentation from your computer or video source.
P/N 692942
Quick Start Guide
KODAK V600 Digital Projector • KODAK V600 Zoom Digital Projector
with Kodak’s Exlusive Image Manager
Using the Remote Control and Keypad
The remote control and projector keypad perform similar operations, except—the remote control has a volume control.
Adjust
Volume
Menu
Next
Power—turns the projector on and off
Menu—displays the menus on the projected
image
Enter—selects an option button
Next—highlights the next feature in the menu
Adjust—navigates between tabs; moves a
highlighted slider bar left or right; and moves
between options for features like Source and
Projection
Volume—increases or decreases volume
Power
Enter
Remote Control
(Optional with V600)
Turning Off the Projector
1. Press the Power button on the keypad or remote control.
A confirmation screen appears.
Projector Safety
Warning: Don’t look directly into the lens when the projector is
turned on. Doing so may cause eye injury.
Warning: To replace the lamp, turn off the power and unplug the
power cord. To avoid burns, wait 30 minutes before opening the
lamp door. Follow all instructions provided in this User Guide. See
“Changing the Lamp Module” on page 23.
Warning: Please use the power cord provided. Connect the power
cord to a receptacle with a protective safety (earth) ground terminal.
Warning: Servicing your own projector may expose you to hazards
or create potential hazards. Also, servicing your own projector will
void the warranty. Refer all service to qualified service personnel.
See “If You Need Assistance” on page 5.
Warning: In the unlikely event of the bulb rupturing, thoroughly
clean the area behind the projector and discard any food that might
have been contaminated with broken glass.
Warning: When replacing the lamp, be sure to turn off the power
and unplug the power cord. To avoid burns, wait 30 minutes before
opening the lamp door.
Warning: When you open the lamp module door, be careful to not
touch the hot surfaces inside.
POWER
MENU
ADJUST
ENTER
NEXT
Keypad
2. Press the Power button again to confirm.
The lamp turns off immediately but the fan continues to run until
the projector cools down.
The Power light continues to blink slowly as long as the live power
cord is connected to the projector.
Warning: Do not loosen or remove any screws other than those on
the lamp module door and the lamp module. Doing so may result
in electric shock.
Caution: Don’t set liquids on the projector. Spilled liquids may
damage your projector.
Caution: Don’t place the projector on a hot surface or in direct
sunlight.
Caution: Do not drop the projector.
Caution: Never operate your projector without the lamp module or
lamp module door. Doing so may damage the projector.
Caution: Don’t block ventilation openings. Never operate this
projector in an enclosed area. Do not place the projector on a
tablecloth or other soft covering that may block the vents. With
ceiling installations, the use of approved mounting hardware is
required. Do not locate the projector near heat ducts, air cleaners,
transformers or other electrical devices. For permanent installations
follow local codes.
Caution: Do not touch the glass portion of the new lamp module
with your hands or allow it to touch other objects as this may damage
it and shorten its operational life.
Caution: Do not drop the lamp module as the glass may shatter
and cause injury.
EASTMAN KODAK COMPANY
Rochester, NY 14650
Kodak is a trademark of Eastman Kodak Company. © Eastman Kodak Company, 2000 Printed in the U.S.A. 3/00
Loading...