Kodak V2CS User Manual

KODAK VISION2

Color Negative Control Strips

Process ECN-2

Technical Data and

V2CS

August, 2004

Crossover Information

©Eastman Kodak Company, 2004

Note: While the data presented are typical of production coatings, they do not represent standards which must be met by Kodak. Varying storage, exposure, and processing conditions will affect results. The company reserves the right to change and improve characteristics at any time.

KODAK VISION2 Color Negative Control Strips

Introduction

KODAK VISION2 Color Negative Control Strips (Figure 1) are intended for the control of Process ECN-2 using the procedures described in KODAK Publication No. H-24,

Manual for Processing KODAK Motion Picture Films, Module 1, Process Control.

The first batch of KODAK VISION2 Color Negative Control Strips is code 5011 for 35 mm, CAT 152 0469 and code 5012 for 16 mm, CAT 152 0444.

Figure 1 Processed Control Strip - 35mm

ECN-2

9071

Steps

4

HD

Important Improvements

KODAK VISION2 Color Negative Control Strips incorporate several important improvements into the control strips for Process ECN-2.

• A VISION2 emulsion is being used for process control. The new format is exposed on KODAK VISION2 200T Color Negative Film 5217, while the former ECN control strip was exposed on KODAK VISION 200T Color Negative Film 5274.

KODAK VISION2 Color Negative Control Strips,

Process ECN-2, are packaged in 100-foot rolls containing at least 120 exposures and a processed reference strip. The exposures on the roll are spaced at 9.5-inch intervals. Each exposure has 21 gray-scale steps at 0.20 log H increments (2/3 camera stop).

The reference strip accompanying each roll was exposed

along with all other control strips; it was then processed under specified well-controlled conditions. An instruction sheet enclosed with the package contains process deviation (correction) factors, if they are required, to determine your laboratory process aim numbers. A four-digit code number appearing on the carton, can, control strips, reference strips, and instruction sheet, identifies each production batch of strips.

8

MD

14 LD

21

D-min

F009_0146CC

KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Information 3

Control Strip Log Exposure Range

The graphs in Figure 2 and Figure 3 demonstrate the differences between the former ECN control strip exposed on KODAK VISION 200T Color Negative Film 5274, and the new format exposed on KODAK VISION2 200T Color Negative Film 5217.

Physically, the center-to-center step distance has been maintained on the new control strips; no problems should be encountered with existing automatic densitometers.

Once the transition to the new control strips is complete, and the new control step reference values have been determined, continue to use KODAK VISION2 Color Negative Control Strips in the same manner as your previous control strips.

Please contact your Kodak representative for additional information on monitoring your process with control strips.

4 KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Information

Figure 2 ECN-2 Control Strip Exposed on KODAK VISION 200T Color Negative Film 5274

3.0

2.0

DENSITY

1.0

Exposure: Process:

1/50 sec

ECN-2

Densitometry:

Status M

B

G

R

0.0

-4.0 -3.0 -2.0 -1.0 0.0 1.0 2.0

LOG EXPOSURE (lux-seconds)

KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Informat ion 5

Figure 3 ECN-2 Control Strip Exposed on KODAK VISION2 200T Color Negative Film 5217

3.0

Exposure:1/50 sec Process: ECN-2 Densitometry: Status M

B

G

2.0

R

DENSITY

1.0

0.0

-4.0 -3.0 -2.0 -1.0 0.0 1.0 2.0

LOG EXPOSURE (lux-seconds)

6 KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Information

Effects of Mechanical and Chemical Variations

Figures 4 through 13 illustrate some of the major photographic effects of mechanical and chemical variations on KODAK VISION2 Color Negative Control Strips exposed on 5217 Film compared to the former VISION Control Strips exposed on 5274 Film. Each plot shows the effect of a change in a process variable (horizontal axis), on the dye density of the processed film (vertical axis). These density plots are deviated against the standard level for each variable (e.g. standard level for the variable is represented by zero density).

The magnitude of the changes shown in these plots should not be considered to be process control limits. Also, the data presented are qualitative, not quantitative. The plots were derived from experiments using small laboratory machines in which all constituents were held constant except the variable being studied. Hence, the figures should be used only as trend charts and guides. If two or more process variable are changed, the resulting photographic effect illustrated may not be additive. Interactions can occur that produce effects other than those predicted by addition. The plots in this publication are representative only; they do not contain all possible solution problems. Most of the important photographic effects take place in the developer.

KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Informat ion 7

Developer Mechanical Factors

Figure 4 Effects of Time and Temperature Variations —VISION2 Control Strips versus VISION Control Strips in Process ECN-2 Developer

AIM VALUES

REFERENCE STRIP CODE NO.

0000

HD

RED

GREEN

BLUE

B/W

MD

RED

GREEN

BLUE

B/W

LD

RED

GREEN

BLUE

B/W

D-min

RED

GREEN

BLUE

B/W

HD-LD

RED

GREEN

BLUE

B/W

V2CSQ_V2CSP_2

.25 .20

.15 .10 .05

+

.05 .10

.15 .20 .25 .20 .15 .10 .05

+

.05 .10 .15

.20 .10 .05

+

.05 .10

.10 .05

+

.05 .10

.10 .05

+

.05 .10

B

R

106

˚

Temperature

B G R

R G

B G R

R G B

G R

R G B

B G

R

G

B

G B

B G

R

108

110

B

102

52745217

104

R G

B

B G R

B G

R

B R G

R G

B

108

106

F

˚

110

Time

5217

B R G

0

R

B

G

B R G

0

R G

B

0

R

B

G

0

R G B

R

0

G

R

B

220

300

240

320

sec F

R G B

B

R

G

B R G

G B

B G

340

5274

B R

G

R G

B R G

B

R

G

340

B

R G B

R

B

G

102

104

R G

B

R G B

G

R B

R

sec

300

320

220

240

8 KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Information

Developer Chemical Factors

Figure 5 Effects of pH and CD-3 Variations —VISION2 Control Strips versus VISION Control Strips in Process ECN-2 Developer

AIM VALUES

REFERENCE STRIP CODE NO.

0000

HD

RED

GREEN

BLUE

B/W

MD

RED

GREEN

BLUE

B/W

LD

RED

GREEN

BLUE

B/W

D-min

RED

GREEN

BLUE

B/W

HD-LD

RED

GREEN

BLUE

B/W

V2CSN_V2CSD_2

.25 .20

.15 .10 .05

+

.05 .10

.15 .20 .25 .20 .15 .10 .05

+

.05 .10 .15

.20 .10 .05

+

.05 .10

.10 .05

+

.05 .10

.10 .05

+

.05 .10

G

B

4.75

G R

R

G

5.50

CD-3

B R

B

52745217

B

G

R

B

G

B G R

R

B

G

B

G R

R

B

G

B

G

R

G B

R

B G

2.50

2.25

4.00

g/L

R

G

R

B

5.50

4.75

pH

5217

B G R

0

R

B

G R

B

G R

R

B G R

G

B

R

10.45

R G

G R B

R B

G

B

0

R G B

0

R G B

R

0

G

B

0

R B G

10.05

10.15

10.25

10.35

B

10.05

5274

10.15

10.25

10.35

B G

R

B G R

B G

R

B R

G

G R

B

10.45

R

B

G

R

B

G

R B

G

R

B

G

B

R

2.50

3.25

4.00

g/LpHpH

KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Informat ion 9

Developer Chemical Factors

Figure 6 Effects of NaBr and AF-2000 Variations —VISION2 Control Strips versus VISION Control Strips in Process ECN-2 Developer

AIM VALUES

REFERENCE STRIP CODE NO.

0000

HD

RED

GREEN

BLUE

B/W

MD

RED

GREEN

BLUE

B/W

LD

RED

GREEN

BLUE

B/W

D-Min

RED

GREEN

BLUE

B/W

HD-LD

RED

GREEN

BLUE

B/W

V2CSK_V2CSA_2

.25 .20

.15 .10 .05

+

.05 .10

.15 .20 .25 .20 .15 .10 .05

+

.05 .10 .15

.20 .10 .05

+

.05 .10

.10 .05

+

.05 .10

.10 .05

+

.05 .10

6.25

AF-2000

B

G

R

B

G

B

R

B

G

R

B

G

B

R

B

G

R

G

B

7.50

2.50

52745217

3.75

5.00

6.25

B G R

G R B

G B R

B R G

7.50

NaBr

5217

B G R

0

B

G R

0

B G R

0

B G R

0

B G R

0

1.2

0.8

1.0

1.4

g/L

B G

R

R G B

B

G

R

R G

B

B G

R

R B G

B

G

R

G

B

G R

B

R G

B

1.6

5274

R G

B

R G

B

R G

B

R G

B

R

B

G

1.2

0.8

1.0

1.4

1.6

g/L ml/Lml/L

G R

B

G B R

G R B

G

R

B

G

R

B

3.75

5.00

2.50

10 KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Information

Developer Chemical Factors

Figure 7 Effects of Na

and Under and Over Replenishment Variations

2SO3

—VISION2 Control Strips versus VISION Control Strips in Process ECN-2 Developer

AIM VALUES

REFERENCE STRIP CODE NO.

0000

HD

RED

GREEN

BLUE

B/W

MD

RED

GREEN

BLUE

B/W

LD

RED

GREEN

BLUE

B/W

D-min

RED

GREEN

BLUE

B/W

HD-LD

RED

GREEN

BLUE

B/W

V2CSL_V2CSR_2

.25 .20

.15 .10 .05

+

.05 .10

.15 .20 .25 .20 .15 .10 .05

+

.05 .10 .15

.20 .10 .05

+

.05 .10

.10 .05

+

.05 .10

.10 .05

+

.05 .10

Na

2SO3

5217

G

R B

G R

B

R G B

R G

B

G R

3.0

R

B G

R G

G R

R B

G

B

R G

0

B G R

0

G

B

R

0

G

B

0

R

B G

0

B

1.5

1.0

2.0

2.5

B

1.0

1.5

5274

g/L

2.0

2.5

G

R

B

G

B

G

R

B

G

R

G

B

G

R

G

B

R

G

B

R

3.0

G

R

B

-20%

Replenishment

B G R

B R

B

G R

B

G

R

B

R G

0.0

g/Lg/L

+20%

52745217

G B R

R G

B

G

B

G

B R

G R

R

B

+20%

G

R B

G

R G

B

R

G

B

R G

B

-20%

0.0

g/L

Under and Over

KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Informat ion 11

Developer Chemical Factors

Figure 8 Effects of PB-C1 and PB-2 Prebath Contamination —VISION2 Control Strips versus VISION Control Strips in Process ECN-2 Developer

Prebath

PB-C1

AIM VALUES

REFERENCE STRIP CODE NO.

0000

HD

RED

GREEN

BLUE

B/W

MD

RED

GREEN

BLUE

B/W

LD

RED

GREEN

BLUE

B/W

D-Min

RED

GREEN

BLUE

B/W

HD-LD

RED

GREEN

BLUE

B/W

V2CSB_V2CSM_2

.25 .20

.15 .10 .05

+

.05 .10

.15 .20 .25 .20 .15 .10 .05

+

.05 .10 .15

.20 .10 .05

+

.05 .10

.10 .05

+

.05 .10

.10 .05

+

.05 .10

5217

0

R

G

B

0

R

G

B

0

0.0

50.0 mL/L

100.0

R

B

R

150.0

G

R

G

B

200.0

0.0

50.0 mL/L

5274

100.0

R

G

R B

150.0

B

R B

G

B

G

B

R

G

200.0

R

B

G

0.0

50.0

100.0

mL/L

B

150.0

PB-2

R G B

G R

B

R G B

G R

R

200.0

0.0

52745217

50.0 mL/L

G

100.0

G

150.0

R B

R G

B

G R B

B R

200.0

12 KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Information

Developer Chemical Factors

Figure 9 Effects of CD-2 for CD-3 and Stop Bath Contaminatio n —VISION2 Control Strips versus VISION Control Strips in Process ECN-2 Developer

AIM VALUES

REFERENCE STRIP CODE NO.

HD

RED

GREEN

BLUE

B/W

MD

RED

GREEN

BLUE

B/W

LD

RED

GREEN

BLUE

B/W

D-min

RED

GREEN

BLUE

B/W

HD-LD

RED

GREEN

BLUE

B/W

0000

.25 .20

.15 .10 .05

+

.05 .10

.15 .20 .25 .20 .15 .10 .05

+

.05 .10 .15

.20

.10 .05

+

.05 .10

.10 .05

+

.05 .10

.10 .05

+

.05 .10

Substitute CD-2 for CD-3

5217

B

0

B

0

G

0

B

0

R

G

R

B

R

B

G

0.0

R

0.5

1.0

R

1.5

BG

B

GB

BG

2.0

5274

R

G

R

G

B

R

0.0

0.5

1.0

R

1.5

B

2.0

5217 5274

G

0

25

50

Stop Bath

R

B G

R G

B

R G

B

R

G

B

R

B

75

100

R G

B

R

B

G

R G

B

G

R

B

R

75

B

100

G

0

25

50

V2CSC_V2CSO_2

g/L

mL/L

KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Informat ion 13

Developer Chemical Factors

Figure 10 Effects of Bleach Contamination —VISION2 Control Strips versus VISION Control Strips in Process ECN-2 Developer

UL Bleach

AIM

VALUES

REFERENCE STRIP CODE NO.

HD

RED

GREEN

BLUE

B/W

0000

.25 .20

.15 .10 .05

+

.05 .10

.15

5217

0

R

G

B

5274

R G

MD

RED

GREEN

BLUE

B/W

LD

RED

GREEN

BLUE

B/W

D-Min

RED

GREEN

BLUE

B/W

HD-LD

RED

GREEN

BLUE

B/W

.20 .25

.20 .15 .10 .05

+

.05 .10 .15

.20

.10 .05

+

.05

.10

.10 .05

+

.05

.10

.10 .05

+

.05

.10

B

0

R G

B

0

0.0

2.0

R B

G

R G B

4.0

6.0

R G

B

8.0

0.0

2.0

R

G

B

G R B

4.0

6.0

G B R

8.0

V2CSU_2

mL/L

14 KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Information

Developer Chemical Factors

Figure 11 Effects of F-34a Fixer and Final Rinse Contamination —VISION2 Control Strips versus VISION Control Strips in Process ECN-2 Developer

AIM VALUES

REFERENCE STRIP CODE NO.

HD

RED

GREEN

BLUE

B/W

MD

RED

GREEN

BLUE

B/W

LD

RED

GREEN

BLUE

B/W

D-min

RED

GREEN

BLUE

B/W

HD-LD

RED

GREEN

BLUE

B/W

V2CSF_V2CSE_2

0000

.25 .20

.15 .10 .05

+

.05 .10

.15 .20 .25 .20 .15 .10 .05

+

.05 .10 .15

.20 .10 .05

+

.05 .10

.10 .05

+

.05 .10

.10 .05

+

.05 .10

R

200

Final Rinse

B

G

R

B

G

R

B G R

B

G

R

B

G

300

400

52745217

B G R

B

G

R

G

B

R

B

G

R

0

100

mL/L

200

300

400

F-34a Fixer

5217

0

0.0

0.25 mL/L

0.50

R G B

R

G

R G B

R G

R B G

0.75

B

1.00

0.0

5274

0.25 mL/L

0.50

R

G

B

R G B

R G

B

R G B

0.75

1.00

0

100

mL/L

KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Informat ion 15

Developer Chemical Factors

Figure 12 Effects of KI Contamination and Water Dilution —VISION2 Control Strips versus VISION Control Strips in Process ECN-2 Developer

AIM VALUES

REFERENCE STRIP CODE NO.

0000

HD

RED

GREEN

BLUE

B/W

MD

RED

GREEN

BLUE

B/W

LD

RED

GREEN

BLUE

B/W

D-min

RED

GREEN

BLUE

B/W

HD-LD

RED

GREEN

BLUE

B/W

V2CSH_V2CSG_2

.25 .20

.15 .10 .05

+

.05 .10

.15 .20 .25 .20 .15 .10 .05

+

.05 .10 .15

.20 .10 .05

+

.05 .10

.10 .05

+

.05 .10

.10 .05

+

.05 .10

Kl

0.0

mg/L

5274

2.5

5.0

R

G

B

R

G B

G R B

G

R B

R

G

B

7.5

G

0

100

5217

5.0

R G

B

R G

B

G

B

R G

B

R G

B

7.5

R

0

2.5

0.0

mg/L

Water Dilution

5217 5274

B

R G

B

G R

B G R

B

G

R

B

mL/L

200

R

400

300

G

0

100

mL/L

R

200

300

B G

R

B G R

B

400

16 KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Information

Developer Chemical Factors

Figure 13 Effects of Bacterial Na

S and Na2CO3 Contamination

2

—VISION2 Control Strips versus VISION Control Strips in Process ECN-2 Developer

AIM

VALUES

REFERENCE STRIP CODE NO.

HD

RED

GREEN

BLUE

B/W

MD

RED

GREEN

BLUE

B/W

LD

RED

GREEN

BLUE

B/W

D-min

RED

GREEN

BLUE

B/W

HD-LD

RED

GREEN

BLUE

B/W

V2CSJ_V2CSI_2

0000

.25 .20

.15 .10 .05

+

.05 .10

.15 .20 .25 .20 .15 .10 .05

+

.05 .10 .15

.20 .10 .05

+

.05 .10

.10 .05

+

.05 .10

.10 .05

+

.05 .10

Na SBacterial

2

5217

G

1.5

R B

G

R B

B G R

G

R

B

2.0

0

0.5

mg/L

1.0

0.0

0.5

mg/L

5274

1.0

1.5

B R

G

B R G

B G R

R G B

2.0

5.6

25.6

15.6 g/L g/L

35.6

Na CO

23

G R

B

G R

B

G R

B

G B

R

G

R B

45.6

5.6

52745217

15.6

25.6

35.6

R B

G

R G B

R G

B

R B G

45.6

KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Informat ion 17

Control-Strip Crossover

Important: During the inventory crossover from the old VISION Control Strips to the new VISION2 Control Strips, every effort should be taken in your operations to avoid switching back and forth. Your process control will be greatly simplified by depleting your supply of the VISION Control Strips (except for what is needed for crossover purposes) prior to utilizing the VISION2 Control Strips.

There will come a time when you will need to begin using a new batch of control strips. A new batch means a new code number, not a fresh box of strips with the same code number. Please be aware no two batches of control strips are identical because of slight differences in product, exposures, process, etc. And therefore, the aim value numbers will not match (however, on rare occasions they could), even with the application of the deviation factors.

When you first started using control strips, you had no previous reference and you set up your aim value parameters by reading the densities of the specified (D-min, LD, MD, HD, or D-max) control reference steps and applying the deviation numbers supplied with that batch. Using a new batch of strips is really no different, except you will have a new set of aim numbers,

As the time approaches to change to a new batch (code), you will want to make a “crossover” from the current, or old batch. Crossover simply means to adapt to a change in aim numbers, not a change in processing technique. You should begin the crossover with at least a week’s supply of strips still available (never wait until you run out).

The crossover to a new batch lets you get a “feel” for the new set of aim numbers. Do not attempt to match the new aim numbers to the old ones. If you do, you probably will find it necessary to change the mechanical and/or chemical specifications of the process, and this will most likely lead to a non-conforming unacceptable process. You will notice some differences in the way the new batch trends as compared to the previous batch. this is a normal batch-tobatch variation, and is to be expected. If you are unable to maintain a plot within your action limits with the new control-strip batch, call your Kodak representative to assist you.

Use the following crossover procedure each time a new

code number is put into service:

• Determine the aim values for the new batch, the same as you did for the current or old batch by reading the specified steps (D-min, LD, MD, and HD or D-max) of the reference strip and applying the correction factors. If there is more than one roll of the same batch, average the corresponding step densities for all reference strips in the batch, then apply the correction factors.

• Process an old and new control strip simultaneously at least three separate times. Do this at different times of the day, and better yet, on different days, until you have a number of pairs. During this time, continue to control the process with data from the old strips.

• Post the new aim values on the same form as the old, leaving an appropriate space between the two aim sets (as illustrated in Figure 14). This way you can see the differences of each control strip reaction at a glance. You will observe the tracking of the “old” batch as compared to the “new” batch, with each plotted to its individual set of aim numbers. Both should be tracking in similar directions, but not exactly. However, they still should be within the same action and control limits. Please remember, no matter how the aim densities differ in numerical value, you still use each set as your zero (0) reference line.

• Once you are comfortable with the new batch of control strips, use a new H-24F or Y-55 form to separate and not confuse the old and new aim numbers while making the daily notations.

• If, for some reason, there is a need to adjust the process to conform to the new batch of control strips to new action and control limits, cease processing and evaluate the entire system. Such a need for change indicates a fundamental system difficulty, which most likely involves all aspects of the process, not necessarily a problem with the new batch of control strips. If difficulty continues, contact your Kodak technical representative.

18 KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Information

Figure 14 Control-Strip Crossover for Process ECN-2

EASTMAN Process Record Form (H-24F)

AIM

VALUES

HD

RED

GREEN

BLUE

B/W

MD

RED

GREEN

BLUE

B/W

LD

RED

GREEN

BLUE

B/W

D-Min

RED

GREEN

BLUE

B/W

HD-LD

RED

GREEN

BLUE

B/W

CONTROL NUMBER

1.39

1.88

2.24

1.00

1.49

1.99

0.34

0.75

1.32

0.11

0.54

0.95

1.05

1.13

0.92

DATES

.25 .20

.15 .10 .05

+

0

.05 .10

.15 .20 .25 .20 .15 .10 .05

+

0 .05 .10 .15 .20

CB action = 0.06 CB control = 0.08

.10 .05

+

0 .05 .10

.10 .05

+

0 .05 .10

CB action = 0.07 CB control = 0.09

.10 .05

+

0

.05

.10

12

1010

TNERRUC

Control Strip Crossover Process ECN-2

12

111111

R-1.19

G-1.69

B-1.98

Code 8051

R-0.85

G-0.97

B-0.93

R-0.33

G-0.72

B-1.05

R-0.15

G-0.54

B-0.95

R-0.86

G-0.97

B-0.93

121212

WEN

12

1012111212

1pm

Kodak and Eastman are trademarks. Printed in U.S.A.

F009_0143EC

4pm

1pm

PROCESS MACHINE Reference Strip Code No.

ECN-2 # 1

4am

7121

1pm

4pm

1pm

8am

EASTMAN KODAK COMPANY ROCHESTER, NY 14650

KODAK Publication No. H-24F

1pm

KODAK VISION2 Color Negative Control Strips, Technical Data and Crossover Informat ion 19

KODAK VISION2 Color Negative Control Strips

MORE INFORMATION

Outside the United States and Canada, please contact your Kodak representative.

You can also visit our web site at www.kodak.com/go/ motion for further information. You may want to bookmark our location so you can find us easily the next time.

KODAK VISION2 Color Negative Control Strips KODAK Publication No. V2CS

Kodak, VISION, and VISION2 are trademarks.

Revised 5-05

Printed in U.S.A.

Kodak V2CS User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

V2CS

Table of Contents

KODAK VISION2 Color Negative Control Strips

Introduction

The first batch of KODAK VISION2 Color Negative Control Strips is code 5011 for 35 mm, CAT 152 0469 and code 5012 for 16 mm, CAT 152 0444.

Important Improvements

KODAK VISION2 Color Negative Control Strips incorporate several important improvements into the control strips for Process ECN-2.

Control Strip Log Exposure Range

Physically, the center-to-center step distance has been maintained on the new control strips; no problems should be encountered with existing automatic densitometers.

Once the transition to the new control strips is complete, and the new control step reference values have been determined, continue to use KODAK VISION2 Color Negative Control Strips in the same manner as your previous control strips.

Please contact your Kodak representative for additional information on monitoring your process with control strips.

Figure 2 ECN-2 Control Strip Exposed on KODAK VISION 200T Color Negative Film 5274

Figure 3 ECN-2 Control Strip Exposed on KODAK VISION2 200T Color Negative Film 5217

Effects of Mechanical and Chemical Variations

Developer Mechanical Factors

Developer Chemical Factors

Developer Chemical Factors

Developer Chemical Factors

Figure 7 Effects of Na

Developer Chemical Factors

Developer Chemical Factors

Developer Chemical Factors

Developer Chemical Factors

Developer Chemical Factors

Developer Chemical Factors

Control-Strip Crossover

MORE INFORMATION

Outside the United States and Canada, please contact your Kodak representative.

You can also visit our web site at www.kodak.com/go/ motion for further information. You may want to bookmark our location so you can find us easily the next time.

Kodak, VISION, and VISION2 are trademarks.