KitchenAid KSM2CB5PHS Owner's Manual

Stand Mixer

KSM2CB5

W11368199A.indd 1			8/23/2019 6:52:46 PM

TABLE OF CONTENTS

PARTS AND FEATURES 3

Parts and Accessories 3

CERAMIC BOWL SAFETY 3

Important Safeguards 3

USING THE CERAMIC BOWL 4

Attaching the Ceramic Bowl to the Stand Mixer 4 Removing the Ceramic Bowl from the Stand Mixer 5

TIPS FOR GREAT RESULTS 5 CARE AND CLEANING 6

2 |

W11368199A.indd 2			8/23/2019 6:52:46 PM

PARTS AND FEATURES

PARTS AND ACCESSORIES

Bowl handle

Pour spout

CERAMIC BOWL SAFETY

<![if ! IE]>

<![endif]>ENGLISH

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed. Please refer to the basic Important Safeguards as outlined in the Instructions manual included with your Stand Mixer.

SAVE THESE INSTRUCTIONS

CERAMIC BOWL SAFETY | 3

W11368199A.indd 3			8/23/2019 6:52:46 PM

USING THE CERAMIC BOWL

ATTACHING THE CERAMIC BOWL TO THE STAND MIXER

Before First Use

Your Stand Mixer is individually adjusted at the factory for optimal performance. When using the Ceramic Bowl, it may be necessary to readjust the beater-to-bowl clearance. When correctly positioned, the handle and pour spout should not touch the pedestal of the Stand Mixer. Please refer to the Stand Mixer Instructions manual for complete information on adjusting the beater-to-bowl clearance.

IMPORTANT: Before use, wash with hot, soapy water; rinse and dry thoroughly. It is not necessary to season the Ceramic Bowl before use.

NOTE: This Ceramic Bowl is designed to fit all 4.3 and 4.8 liters Tilt Head Stand Mixer models except model KN15E1X. Follow these instructions to attach the Ceramic Bowl to your Stand Mixer.

	Be sure the speed control is set
1	to 0 (off) and the Stand Mixer is
	unplugged. Tilt the motor head
	back.

Place the Ceramic Bowl on the

2clamping plate, and attach by turning gently in a clockwise direction.

Attach the appropriate accessory for your recipe, using the directions

3in the Stand Mixer Instructions manual. Then place the motor head back in the down position and lock into place.

4 | USING THE CERAMIC BOWL

W11368199A.indd 4			8/23/2019 6:52:47 PM

USING THE CERAMIC BOWL

REMOVING THE CERAMIC BOWL FROM THE STAND MIXER

		Raise the motor head: Check to	Remove the accessory: Press the
		be sure that the Stand Mixer is
			accessory upward as far as possible,
		unplugged, and the speed control
	1		2 then turn the accessory clockwise
		is turned to “0”; then, slide the
		locking lever to the unlock position	and pull it away from the beater
			shaft.
		and lift the motor head.

Remove the ceramic bowl:

3Gently turn the ceramic bowl counterclockwise to release it from the bowl clamping plate.

<![if ! IE]>

<![endif]>ENGLISH

TIPS FOR GREAT RESULTS

•The Ceramic Bowl is safe for cooking or reheating in the microwave.

•The Ceramic Bowl is oven safe to 482°F (250°C); however, it is not recommended to place the Ceramic Bowl directly under the broiler.

•IMPORTANT: To avoid damaging the Ceramic Bowl, do not use on stovetop or with any other direct heat, such as broiler, grill, toaster oven, or direct flame.

•Baking time can vary when using ceramic bakeware. Monitor and adjust the cooking time as needed.

•Use a hot pad before placing the hot Ceramic Bowl on an unprotected surface.

•To avoid possible damage, do not set the hot Ceramic Bowl on a cold or wet surface. Do not place a frozen Ceramic Bowl in a hot oven.

•After removal from the oven, the Ceramic Bowl will retain heat longer than standard bakeware.

TIPS FOR GREAT RESULTS | 5

W11368199A.indd 5			8/23/2019 6:52:47 PM