Kia AV2A0CSAN User Manual
DIGITAL NAVIGATION SYSTEM
User's Manual
Thank you for purchasing this Audio
Navigation System.
This user's manual explains how to use
the Kia Motor Audio Navigation System.
Before using the product, read the
contents of this user's manual carefully
and use this product safely.
●
The screens shown in this manual
may differ with the actual screens of
the product.
●
The design and specification of this
product may change without prior
notification for product improvement.
●
When tr ansfer r ing th e vehi cle to
another individual, include this user's
manual so that the next driver can
continue its use.
iPod®
iPod® is a registered trademark of Apple
Inc.
Bluetooth®
The Bluetooth® word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by Kia is under license.
A Bluetooth® enabl ed cell phone is
required to use Bluetooth® wireless
technology.
Preface
All Map Database cannot be copied without permission.
This is protected by U.S. copyright laws. All rights not expressly granted are reserved.
You may not otherwise reproduce, modify, and distribute the content without M&Soft, Inc's prior written consent.
PART 1
PRE-OVERVIEW
Introduction ………………………… 1-2
Controller and functions …………… 1-3
Basic operation and setting ………… 1-7
PART 2
AUDIO SYSTEM
Operating the radio ………………… 2-2
Operating the CD Player ………… 2-10
Operating external devices ……… 2-22
PART 3
NAVIGATION SYSTEM
Limitations of the navigation
system ……………………………… 3-2
Map Functions ……………………… 3-5
Setting a destination …………… 3-12
Operating after setting
a destination ……………………… 3-28
Route guidance …………………… 3-30
Setup and Information …………… 3-36
PART 4
VOICE COMMAND SYSTEM
Operating voice command ………… 4-2
Setting up the voice command
system ……………………………… 4-4
Voice command list ………………… 4-6
Table of contents
PART 5
Bluetooth® HANDS FREE
Before using the Bluetooth®
Handsfree …………………………… 5-2
Converting Bluetooth® Handsfree
mode ………………………………… 5-2
Pairing and connecting a Bluetooth®
phone ………………………………… 5-4
Bluetooth® Handsfree screen
layout ………………………………… 5-9
Making a call ……………………… 5-11
Answering a call ………………… 5-13
Operating menus during a call …… 5-14
Phone Book ……………………… 5-16
Call History List …………………… 5-19
Phone Music ……………………… 5-21
Bluetooth® settings ……………… 5-24
Important information …………… 5-30
PART 6
HVAC MODE
Cautions upon operating HVAC
mode ………………………………… 6-2
HVAC mode screen layout ………… 6-2
HVAC System operations …………… 6-3
PART 7
REAR CAMERA
About Rear Detection Camera
………… 7-2
PART 8
APPENDIX
Troubleshooting guide ……………… 8-2
Map legend ………………………… 8-5
INDEX ………………………………… 8-8
Table of contents
PRE-OVERVIEW 1-1
PRE-OVERVIEW
PART 1
PRE-OVERVIEW
Introduction ………………………… 1-2
Important information about this
manual
………………………………… 1-2
Precaution for safe usage
……………… 1-2
Controller and functions …………… 1-3
Control panel …………………………… 1-3
Steering wheel remote controller
……… 1-5
HVAC System
…………………………… 1-6
Basic operation and setting ………… 1-7
Turning the Power ON ………………… 1-7
System Power ON ……………………… 1-7
Turning the Power OFF ………………… 1-7
Turning the Audio ON/OFF
…………… 1-7
Adjusting audio volume
………………… 1-8
How to operate the screen menu
……… 1-8
Operating typical screen menu ………… 1-8
Inputting letter by using screen
keyboard
………………………………… 1-8
Displaying the list ……………………… 1-8
Selecting an item in a list ……………… 1-9
Sorting items from list ………………… 1-9
How to operate menu by voice
command
……………………………… 1-9
Conditions for voice recognition
system
…………………………………… 1-9
Giving voice command
…………………1-10
Sound setting ……………………………1-10
FAD/BAL ………………………………… 1-10
BASS/MID/TREB
………………………… 1-11
Auto volume control ON/OFF
………… 1-11
Touch screen beep ON/OFF
…………… 1-11
Display setting ………………………… 1-11
Display mode …………………………… 1-11
Brightness
……………………………… 1-11
Display OFF
…………………………… 1-11
Display ON
……………………………… 1-11
Setting Picture Frame …………………… 1-12
Display Picture Frame
………………… 1-12
Viewing Current Time
………………… 1-12
Setting the Clock
……………………… 1-13
PART 1 PRE-OVERVIEW
1-2 PRE-OVERVIEW
PART 1 PRE-OVERVIEW
Introduction
Important information about this
manual
This user manual contains instructions related
to safety. Closely observe and comply with all
of the safety instructions found within this
manual.
WARNING !
Disobeying the warnings listed within this
user's manual may cause fatal or serious inju-
ries. Warnings indicate matters which may
directly lead to accidents.
CAUTION!
Disobeying the cautions listed within this user
manual may lead to accidents or cause injury.
Cautions indicate matters which may lead to
vehicle damage or malfunction.
INFORMATION
Information which the user must be aware or
allows for more convenient use of the device.
Precaution for safe usage
WARNING !
●
Do not operate the Audio Navigation system
while driving.
●
Do not disassemble, assemble, or modify the
Audio Navigation system.
●
Do not watch the screen for prolonged peri-
ods of time while driving.
●
Set the volume to a level which allows the
driver to be aware of external conditions.
CAUTION!
●
Do not operate the Audio Navigation sys-
tem for prolonged periods of time with the
vehicle ignition in ACC. Such operations
may lead to battery discharge.
●
Be cautious not to spill water or introduce
foreign objects into the device.
●
Do not cause severe shock to the device.
Direct pressure onto the front side of the
monitor may cause damage to the LCD or
touch panel.
●
In case of product malfunction, please con-
tact your place of purchase or service cen-
ter.
●
When cleaning the touch screen, make sure
to turn off the device and use a dry and
smooth cloth. Never use tough materials,
chemical cloths, or solvents (alcohol, ammo-
nia, benzene, thinners, etc.) as such materials
may damage the device panel or cause color
and quality deterioration.
Reference Page
This indicates the title and page that you
should refer to.
This indicates a key on the control panel.
Voice Command
This indicates an operation by voice com-
mand.
PRE-OVERVIEW 1-3
PRE-OVERVIEW
1
Power / Volume control knob
●
Push knob (over 0.8 second) : turns the
power off.
●
Push knob (under 0.8 second) : each time the
knob is pressed, the Audio is turned on and off.
●
Tune knob : the range of volume adjustment
is between 0 ~ 35.
2
SEEK/TRACK Up/Down
●
SHORT KEY(less than 0.8 second)
• FM/AM Mode : automatically searches for
the previous or next broadcast frequency
and starts playing.
• SAT Mode : receives the previous or next
channel.
• CD Mode : plays the previous or next track.
• MP3, USB Mode : Plays the previous or
next file.
• iPod Mode : plays the previous or next song.
●
LONG KEY(over 0.8 second)
• FM/AM Mode : quickly moves through the
frequencies while the button is pressed.
Once released, automatically searches for
broadcasts which can be received.
• SAT Mode : quickly moves to the previous
or next channel.
• CD Mode : REW/FF the curre nt playi ng
track.
• MP3, USB Mode : REW/FF the current play-
ing file.
• iPod Mode : REW/FF the current playing
song.
3
FM/AM
Each press will change the bands in the fol-
lowing order: FM1
→
FM2
→
AM → FM1 ...
Controller and functions
Control panel
1
2
12
3 4 5
10 11
13
6
7 8 9
1-4 PRE-OVERVIEW
PART 1 PRE-OVERVIEW
4
SAT
Each press will change the bands in the fol-
lowing order: SIRIUS1
→
SIRIUS2
→
SIRIUS3
→
SIRIUS1 ...
5
MEDIA
Each press will change the bands in the fol-
lowing order: DISC(CD, MP3)
→
(USB or iPod)
→
(AUX) → (Phone Music)
→
DISC(CD, MP3)...
6
TUNE
●
FM/AM Mode : push the keys to search for
the desired frequency. Press the key to
receive the selected frequency.
●
SAT Mode : push the keys to search for the
desired channel. Press the knob to receive
the selected channel.
●
CD Mode : push the keys to search for the
desired track. Press the key to play the
selected track.
●
MP3, USB Mode : push the keys to search
for the desired file. Press the key to play
the selected file.
●
iPod Mode : push the keys to search for the
desired song. Press the key to play the
selected song.
7
PHONE
Displays the Bluetooth handsfree screen.
8
MAPVOICE
Displays the map screen for the current posi-
tion.
9
DEST
Displays the displays setting screen.
10
ROUTE
Displays the Route menu screen.
11
SETUP
Displays the Setup menu screen.
12
DISC eject
Ejects the inserted disc.
13
CLOCK
●
Short Key (under 0.8 second)
• When the screen is turned on : displays
th e current time in the center of the
screen.
• When the screen is turned off : turns the
full clock screen on and off.
●
Long Key (over 0.8 second)
• Displays the clock setting screen.
INFORMATION
If pressing and holding the
POWER/VOL
key
for over 0.8 seconds does not shut down the
sy ste m, press the
FM/AM
and
MAP VOICE
keys simultaneously for over 10 seconds to
reset the sof tware. The system power will
shut-off and the system will restart.
PRE-OVERVIEW 1-5
PRE-OVERVIEW
Steering wheel remote controller
1
MODE
Each time the Mode key is pressed, the mode
changes in the following order: FM1
→
FM2
→
AM → SIRIUS1 → SIRIUS2 → SIRIUS3 →
(DISC)
→
(USB or iPod) → (AUX) → (Phone
Music)
→
FM1 ...
If an unsupported DISC is inserted, if there is
no disc, or if an external device (e.g. iPod, USB
memory stick, etc.) has not been connected,
the mode will not be recognized and auto-
matically switch to the next mode.
●
Press this key for over 0.8 second to turn the
Audio ON and OFF.
●
Press this key when the Power is turned off
to turn the power on.
2
Volume Up/Down
Increases or decreases the volume within a
range between 0 ~ 35. Volume for navigation
and voice guidance can be adjusted in the
setup mode.
3
Seek Up/Down
●
SHORT KEY(less than 0.8 second)
• FM/AM : receives the previous or next pre-
set frequency.
• SIRIUS Mode : receives the previous or
next preset channel.
• CD Mode : plays the previ ous or nex t
track.
• MP3, USB Mode : plays the previous or
next file.
• iPod Mode : plays the previous or next
song.
●
LONG KEY(Over 0.8 second)
• FM/AM Mode : quickly moves through the
frequencies while the key is pre sse d.
Once released, automatically searches for
broadcasts which can be received.
• SIRIUS Mode : quickly moves to the previ-
ous or next channel.
• CD Mode : REW/FF the current playing track.
• MP3, USB Mode : REW/FF the current play-
ing file.
• iPod Mode : REW/FF the current playing
song.
4
Voice Recognition
Starts Voice Recognition.
5
CALL
Press this key to receive an incoming call. If
pressed while in Audio/Navigation mode, the
bluetooth handsfree screen will be displayed.
6
END
Press this key to reject an incoming call.
If pressed while on a call, then the call will be
terminated.
1
6
3
2
4
5
1-6 PRE-OVERVIEW
PART 1 PRE-OVERVIEW
HVAC System
1
TEMP
Raises or lowers the driver-side temperature.
2
A/C
Turns the air conditioner ON/OFF.
3
Switches the air intake mode to recirculation
or exterior mode.
4
FRONT
Removes humidity and frost by blowing fan
towards the front window.
5
REAR
The rear window defroster is turned ON/OFF.
When the defroster is operating, the light on
the display window and at the top of the
switch will turn on.
6
(FAN)
Sets the fan level.
7
AUTO
Operates heating/cooling auto mode which
maintains cabin temperature at suitable levels
by using the outside temperature sensor.
Once AUTO mode is operated, the light at the
top of the switch will turn on.
8
MODE
Sets the fan direction.
9
OFF
Turns the HVAC system off.
10
CLIMATE
Displays the general status of the HVAC sys-
tem, such as temperature, outside tempera-
ture, fan mode, and fan level.
6
2
4
8
10
3
9
5
7
1
PRE-OVERVIEW 1-7
PRE-OVERVIEW
Basic operation and setting
Turning the Power ON
1. Turn the ignition key onto ACC or ON. If the
system power had been on when the igni-
tion was turned off, the system will turn
back on automatically.
2. If the system power had been off when the
ignition was tur ned off, the system wil l
remain off. In this case, press the
POWER/VOL
knob to turn on the system power.
System Power ON
INFORMATION
As system booting starts from the point the
door lock is unlocked, the device may com-
plete booting before the ACC is turned on or
the
POWER/VOL
knob is pressed.
Consequently, the booting screen may not be
displayed upon initially turning on the system
power.
3. Once system booting is complete, the most
recent operated mode will be displayed. For
example, turning on the system will display
FM1 radio mode if the last operated mode
prior to turning off the system had been
FM1 radio mode.
Turning the Power OFF
If the
POWER/VOL
knob is pressed for over 0.8
second, a beep will sound and the system
power will be turned off.
Turning the Audio ON/OFF
Press the
POWER/VOL
knob for under 0.8 sec-
ond with the system power on to turn the
Audio on and off.
Voice Command
1. Press the key on the steering wheel
remote controller.
2. After the beep sound, say a command.
"Audio On"
"Audio Off"
INFORMATION
Conducting the following operations while
the AUDIO is off will automatically turn on the
Audio system.
●
Pressing the Audio related keys (
FM/AM
,
SAT, MEDIA
).
●
Inserting a DISC or connecting an external
device.
1-8 PRE-OVERVIEW
PART 1 PRE-OVERVIEW
Adjusting audio volume
Turn the
POWER/VOL
knob in clockwise direc-
tion to increase the vo lume and counter-
clockwise to decrease the volume.
INFORMATION
●
The range of volume adjustment is between
0 ~ 35.
●
Adjustments to the volume cannot be made
while the AUDIO is turned off.
How to operate the screen menu
Operating typical screen menu
●
If a menu button on the screen is pressed,
the corresponding function will begin oper-
ation.
●
The same menu button may perform differ-
ent functions depending on the length of
time the button is pressed (under 0.8 sec-
onds or over 0.8 second). For more informa-
tion, refer to the specific function within this
user manual.
●
The current operated button will be high-
lighted upon display.
●
Buttons which cannot be operated under
the current conditions will be displayed in
disabled state. Pressing a disabled button
will not perform any operation.
Inputting letter by using screen
keyboard
ABC
: Displays the English alphabet keypad.
: Displays the French alphabet keypad.
(if available)
0 - 9
: Displays the number and symbol key-
pad.
Delete
: Deletes the previously inputted letter.
Pressing for over 0.8 second will delete
all content.
Space
: The input is completed.
: Restores to previous screen. The inputted
text will not be saved.
Displaying the list
List
: Even if input is not complete, the cur-
rent matching items from the data-
base will be displayed.
INFORMATION
The number at the upper-right side of the
screen displays the number of current matches.
PRE-OVERVIEW 1-9
PRE-OVERVIEW
Selecting an item in a list
: Moves to the next page or previous
page.
:
The button will be displayed if
the text is too long to be displayed in
one button.
Press the
button to move the cursor to
the end of the text. Press the button to
move the cursor to the front of the text.
Sorting items from list
Select the desired sorting method to reorga-
nize the list in accordance to the selected
method.
How to operate menu by voice
command
Conditions for voice recognition system
Most of the functions within the Audio and
Navigation system can be operated by voice.
Please follow the instructions below for opti-
mal voice recognition performance.
●
Close all windows and the sunroof. The
voice recognition can be improved when in
a quiet environment.
●
Press the voice recognition button and say
the desired voice command after the sound
of the beep.
●
The microphone is positioned above the
driver so that voice commands can be said
while maintaining a proper posture.
●
Pronounce the voice commands naturally
and clearly as if in normal conversation.
1-10 PRE-OVERVIEW
PART 1 PRE-OVERVIEW
Giving voice command
1. Press the key on the steering wheel
remote controller.
A voice command window will be displayed
on the lower side of the screen followed by
a "Command please" system voice com-
ment.
2. Once the icon changes into the
icon on the pop-up screen with a beep
sound, say the desired voice command.
[Voice command list], page 4-6.
[ Searching a destination by voice com-
mand], page 4-19.
INFORMATION
Press the key shortly to input the desired
voice command. The system voice instruction
comment will immediately terminate. When
the
icon changes into the icon with a
beep sound, it is possible to input voice com-
mands.
Audio Sound setting
Press the
Sound
button on the main screen of
each Audio mode (FM/AM, SIRIUS, CD, MP3,
USB, iPod and AUX) to display the Sound set-
ting screen.
FAD/BAL
The position of the sound can be adjusted by
using the up-down and left-right (
, ,
, ) buttons on the lef t si de of the
screen.
Press the
Default
but ton to posit ion the
sound in the center of the vehicle.
PRE-OVERVIEW 1-11
PRE-OVERVIEW
BASS/MID/TREB
The BASS/MID/TREB can be adjusted by using
the left/right buttons (
, ) of each con-
trol.
Auto volume control ON/OFF
Each time the
Auto volume control
button is
pressed, the Auto volume control function is
turned on or off.
INFORMATION
The Auto Volume Control is a function which
automatically adjusts the volume level in
accordance to changes in vehicle speed.
Touch screen beep ON/OFF
Ea ch time the
Touch screen beep
button is
pressed, the beeping sound that follows each
press on the screen will turn on or off.
Display setting
Press the
DISP
key on the control panel to
display the Setup menu screen.
Display mode
Press the button for the desired display mode
f ro m
Automatic, Daylight
, a nd
Night
modes. The current selected mode is high-
lighted.
●
Automatic
The display is auto maticall y conver ted
be twe en Dayl igh t and Ni ght modes in
accordance to the on/off state of the vehi-
cle taillights.
●
Daylight
The bright screen is always maintained
regardless of the on/off state of the vehicle
taillights.
●
Night
Th e dark screen is alw ays maint aine d
regardless of the on/off state of the vehicle
taillights.
Brightness
Use the left/right buttons ( , ) for con-
trol to make adjustments.
Display OFF
Press the
Display Off
button.
Display ON
Press anywhere on the black screen.
The screen prior to display setting will be dis-
played.
1-12 PRE-OVERVIEW
PART 1 PRE-OVERVIEW
Setting Picture Frame
Display Picture Frame
1. Press th e
Picture Frame
bu tt on in t h e
DISPLAY Setup screen.
2. Press the
My Image
button in the <Picture
Frame> Setup screen.
3. The registered image will be displayed once
power is turned off.
INFORMATION
For Picture Frame setup, the frame must be
set in USB Image mode. (For details on setting
the Picture Frame, refer to the USB IMAGE
page.)
4. To delete an image registered as a frame,
press the
Delete Image
button.
Viewing Current Time
Press the
CLOCK
on the front panel shortly
(under 0.8 second) to display the current time
at the center of the screen.
INFORMATION
If the scree n is turned of f, selectin g the
CLOCK
will display the current time on the
entire screen.
PRE-OVERVIEW 1-13
PRE-OVERVIEW
Setting the Clock
Press and hold the
CLOCK
on the front panel
(over 0.8 second) to display the Clock setting
screen.
●
GPS Time
The time received from the GPS will be dis-
played automatically.
●
Clock Type
Selec ts the clock type shown as the entire
screen when the system power is turned off.
●
Time Format
When the clock type is digital, this button is
used to convert the time between 12 hour/ 24
hour systems.
●
Daylight Saving Time
Turns the Daylight Saving Time function on or
off.
INFORMATION
Clock setting mode can be displayed while
the clock is displayed on the screen even
when the system is turned off.
PART 2 AUDIO SYSTEMPART 2 AUDIO SYSTEM
PART 2
AUDIO SYSTEM
Operating the radio ………………… 2-2
FM/AM Radio …………………………… 2-2
Listening to the FM/AM radio ………2-2
FM/AM screen and functions
…………2-2
Selecting FM/AM broadcast
frequency
……………………………2-3
Storing FM/AM preset
………………2-4
Scanning FM/AM broadcast
frequency
……………………………2-5
SIRIUS radio……………………………… 2-6
Listening to the SIRIUS radio …………2-6
SIRIUS screen and functions
…………2-6
Switching the SIRIUS mode
(Channel / Category)
…………………2-7
Selecting SIRIUS broadcast channel
…2-7
Storing SIRIUS preset
…………………2-9
Scanning SIRIUS broadcast channel
…2-9
Operating the CD Player …………… 2-10
About CD Player ………………………… 2-10
Precautions upon handling discs … 2-10
For safe and efficient operation
…… 2-10
Supported disc formats
…………… 2-11
Disc/Content format compatibility
… 2-12
Inserting/Ejecting Disc ………………… 2-13
Inserting a Disc …………………… 2-13
Ejecting a Disc
…………………… 2-13
CD ……………………………………… 2-14
Listening to CD music …………… 2-14
CD screen and functions
………… 2-14
Selecting the CD track
…………… 2-14
REW/FF CD track
…………………… 2-15
Setting Repeat function for
CD music
…………………………… 2-15
Setting Random function for
CD music
…………………………… 2-15
Scanning CD track ………………… 2-16
MP3 …………………………………… 2-17
MP3 disc related information and
precaution ………………………… 2-17
Listening to MP3 music
…………… 2-18
MP3 screen and functions
………… 2-18
Selecting to MP3 music
…………… 2-19
REW/FF MP3 file
…………………… 2-20
Viewing detail information for
MP3 file …………………………… 2-20
Setting Repeat function for
MP3 file
…………………………2-20
Setting Random function for
MP3 file
…………………………… 2-20
Scanning MP3 file
………………… 2-21
AUDIO SYSTEM 2-1
AUDIO SYSTEM
PART 2
AUDIO SYSTEM
Operating external devices ……… 2-22
iPod® …………………………………… 2-22
Connecting iPod device …………… 2-22
Listening to iPod music ……… 2-22
iPod screen and functions ………… 2-23
Selecting an iPod song
…………… 2-23
REW/FF iPod song
………………… 2-24
Setting Repeat function for
iPod song
………………………… 2-25
Setting Random function for
iPod song
……………………… 2-25
USB MP3 ………………………………… 2-26
USB MP3 related information and
precaution
………………………… 2-26
Precautions upon handling USB
… 2-26
Connecting the USB
……………… 2-28
Listening to USB music
…………… 2-28
USB IMAGE Mode ……………………… 2-29
Starting USB IMAGE Mode ………… 2-29
USB IMAGE mode menu screen
configuration
……………………… 2-29
Operating USB IMAGE Mode
……… 2-30
AUX ……………………………………… 2-31
Connecting AUX …………………… 2-31
Playing AUX
……………………… 2-31
AUX screen
………………………… 2-31
2-2 AUDIO SYSTEM
PART 2 AUDIO SYSTEM
Operating the radio
FM/AM Radio
Listening to the FM/AM radio
1. Press the
FM/AM
key on the control panel.
The FM/AM radio band of the most recent
listened station will be displayed.
2. Pr es s the
FM/AM
ke y to chan g e the
desired radio band. Each press will change
the bands in the following order: FM1
→
FM2
→ AM →
FM1 ...
3. Select the desired broadcast frequency.
[Selecting FM/AM broadcast frequency],
page 2-3.
Voice Command
1. Press the key on the steering wheel
remote controller.
2. After the beep sound, say a command.
" Radio"
"(Radio) AM"
"(Radio) FM"
"(Radio) FM <1 or 2>"
"AM Frequency <530 to 1710>"
"FM Frequency <87.5 to 107.9>"
"AM Preset <1 to 6>"
"FM <1 or 2> Preset <1 to 6>"
FM/AM screen and functions
1
Mode display : displays the FM1/FM2/ AM
modes.
2
SEEK/SCAN/PRESET SCAN/AUTO PRESET
indicator : if SEEK/SCAN/PRESET SCAN /
AUTO PRESET is operating, the switch is
displayed.
3
Frequency : displays the current playing
frequency.
1
3
5 4
6
2
8
7
f
a
b
g
h i
c
ed
AUDIO SYSTEM 2-3
AUDIO SYSTEM
4
STEREO indicator : if the current frequency
is a stereo broadcast, the indicator is dis-
played
5
Program Service name: displays the pro-
gram service name if data is being broad-
casted.
6
Program Type name: displays the program
type name if data is being broadcasted.
7
Frequency bar : displays the position of
the current frequency within the total fre-
quency range.
8
Radio Text: displays the radio text informa-
tion if data is being broadcasted.
a
BAND
butt on : chang es th e desi red
radio band. Each press will change the
bands in the following order: FM1 → FM2
→
FM1...
b c
/ (TUNE Up/Down) button
●
SHORT KEY(less than 0.8 second)
•
The frequency is increased or decreased by
1- ste p inc rem ents (FM : 0.2M Hz, AM :
10kHz).
●
LONG KEY(over 0.8 second)
•
Th e fre quen cy is rapi dly incr eas ed or
de crease d by 1-step incremen ts (FM :
0.2MHz, AM : 10kHz) and stops operation
upon KEY RELEASE.
d e
/ (SEEK Up/Down) button
●
SHORT KEY(less than 0.8 second)
•
Automatically searches for the previous or
next broadcast frequency and starts playing.
●
LONG KEY(over 0.8 second)
•
Quick ly moves through the frequencies
while the button is pressed. Once released,
it automatically searches for broadcasts
which can be received.
f
Preset buttons : the desired frequency can
be preset and selected.
[Storing FM/AM presets], page 2-5.
g
R.Text
butt on : turns the Rad io Text
information on and off.
INFORMATION
If the
R.Text
is on OFF state, text will not be
displayed even if there is text being transmit-
ted from the broadcast station.
If the
R.Text
is on ON state, the frequency
bar will not be displayed. Even if the
R.Text
in on ON state, text may not be displayed if
text is not being received from the broadcast
station.
h
Scan
button : scans all frequencies or
just the preset frequencies for 5 seconds
each.
[Scanning FM/AM broadcast frequency],
page 2-5.
i
Sound
butto n : adj usts the FAD/ BAL ,
BASS/MID/TREB controls.
[Audio Sound setting], page 1-11.
Loading...