Kenwood X1200M User Manual [en, es, fr]

X1200M

CLASS D MONO POWER AMPLIFIER 7 page 2-7

INSTRUCTION MANUAL

AMPLIFICATEUR MONO CLASSE D 7 page 8-13

MODE D’EMPLOI

AMPLIFICADOR DE POTENCIA CLASE D MONOFÓNICO

7 página 14-19

MANUAL DE INSTRUCCIONES

Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new power amplifier.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model X1200M Serial number

US Residence Only

Regi ster your Kenwood produc t a t

ww w.kenwoodusa.com

2 English

Safety precautions

8Ω

2Ω

4Ω

4Ω4Ω4Ω

WARNING

To prevent injury or fire, take the following precautions:

• Mounting and wiring this product requires skills and experience. For safety’s sake, leave the mounting and wiring work to professionals.

• When extending the ignition, battery, or ground wires, make sure to use automotive-grade wires or other wires with the range of 14 mm (AWG 6) to 21 mm (AWG 4) to prevent wire deterioration and damage to the wire coating.

• To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit.

• If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer.

• Do not touch the unit during use because the surface of the unit becomes hot and may cause burns if touched.

CAUTION

To prevent damage to the machine, take the following precautions:

• Be sure the unit is connected to a 12V DC power supply with a negative ground connection.

• Do not open the top or bottom covers of the unit.

• Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.

• When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction.

• To prevent a short circuit when replacing a fuse, first disconnect the wiring harness.

NOTE

• If you experience problems during installation, consult your Kenwood dealer.

• If the unit does not seem to be working right, consult your Kenwood dealer.

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Cleaning the unit

If the front panel gets dirty, turn off the power and wipe the panel with a dry silicon cloth or soft cloth.

CAUTION

Do not wipe the panel with a hard cloth or a cloth dampened by volatile solvents such as paint thinner and alcohol. They can scratch the surface of the panel and/or cause the indicator letters to peel off.

To prevent battery rise

When the unit is used in the ACC ON position without turning the engine ON, it depletes the battery. Use it after starting the engine.

Protection function

The protection function is activated in the following situations: This unit is equipped with a protection function for protecting this unit and your

speakers from various accidents or problems that can occur. When the protection function is triggered, the PROTECTION indicator lights and

the amplifier stops operating.

• When a speaker wire may be short-circuited.

• When a speaker output contacts ground.

• When the unit malfunctions and a DC signal is sent to the speaker output.

Wiring

• Take the battery wire for this unit directly from the battery. If it’s connected to the vehicle’s wiring harness, it can cause blown fuses etc.

• If a buzzing noise is heard from the speakers when the engine is running, connect a line noise filter (optional) to each of the battery wire.

• Do not allow the wire to directly contact the edge of the iron plate by using Grommets.

• Connect the ground wire to a metal part of the car chassis that acts as an electrical ground passing electricity to the battery‘s negative · terminal. Do not turn the power on if the ground wire is not connected.

• Be sure to install a protective fuse in the power cord near the battery. The protective fuse should be the same capacity as the unit’s fuse capacity or somewhat larger.

• For the power cord and ground, use a vehicle type (fireproof ) power wring cord with a current capacity greater than the unit’s fuse capacity. (Use a power wiring cord with the range of 14 mm (AWG 6) to 21 mm (AWG 4).

• When more than one power amplifier are going to be used, use a power supply wiring wire and protective fuse of greater current-handling capacity than the total maximum current drawn by each amplifier.

Speaker Selection

• The rated input power of the speakers that are going to be connected should be greater than the maximum output power (in Watts) of the amplifier. Use of speakers having input power ratings that are less than the output power of the amplifier will cause smoke to be emitted as well as damage.

• Use speakers that have an impedance of 1 or greater. When more than one set of speakers are going to be used, calculate the combined impedance of the speakers and then connect suitable speakers to the amplifier.

Combined impedance

NOTE

This Class B digital apparatus complies with Canadian ICES-003.

Installation

380 mm 320 mm

ø 6

286 mm

272 mm

Hexagon socket head cap screw (M4 × 8 mm)

Cooling fan

Self-tapping screw (ø5 × 18 mm)

Dressing cover

Hexagon Wrench (Small)

Installation board, etc. (thickness : 15 mm or more)

Accessories

Part name External View Number of Items

Self-tapping screws (ø5 × 18 mm)

Hexagon Wrench (Large) 1

Hexagon Wrench (Small) 1

Terminal cover (Power terminal) 1

Installation procedure

Since there are large variety of settings and connections possible according to applications, read the instruction manual well to select the proper setting and connection.

1. Remove the ignition key and disconnect the negative · terminal of the

battery to prevent short circuits.

2. Set the unit according to the intended usage.

3. Remove the Dressing cover.

4. Connect the input and output wires of the units.

5. Connect the speaker wires.

6. Connect the power wire, power control wire and grounding wire following

this order.

7. Install the installation fittings in the unit.

8. Attach the unit.

9. Install the remote controller. (Optional accessory)

10. Attach the Dressing cover.

11. Connect the negative · terminal of the battery.

CAUTION

• Do not install in the below locations; (Unstable location, In a location that interferes with driving, In a location that gets wet, In a dusty location, In a place that gets hot, In a place that gets direct sunlight, In a location that gets hit by hot air)

• Do not install the unit under the carpet. Otherwise heat build-up occurs and the unit may be damaged.

• Install this unit in a location which allows heat to easily dissipate. Once installed, do not place any object on top of the unit.

• The surface temperature of the amplifier will become hot during use. Install the amplifier in a place where people, resins, and other substances that are sensitive to heat will not come into contact with it.

• When making a hole under a seat, inside the trunk, or somewhere else in the vehicle, check that there is nothing hazardous on the opposite side such as a gasoline tank, brake pipe, or wiring harness, and be careful not to cause scratches or other damage.

• Do not install near the dashboard, rear tray, or air bag safety parts.

• The installation to the vehicle should securely fasten the unit to a place in which it will not obstruct driving. If the unit comes off due to a shock and hits a person or safety part, it may cause injury or an accident.

• After installing the unit, check to make sure that electrical equipment such as the brake lamps, turn signal lamps and windshield wipers operate normally.

■ Remote controller (Optional accessory)

Mounting bracket

Remote controller

Self-tapping screw (ø2.6 × 12 mm)

Accessories

Part name External View Number of Items

Remote cable (6.0 m : 19.7 ft) 1

Remote controller 1

Mounting bracket 1

Self-tapping screws (ø2.6 × 12 mm)

English 3

4 English

P.CON SPEAKER OUTPUT

REMOTE

FUSE[30Ax3

]

GNDBATT.

LINE IN LINE OUT

SPEAKER OUTPUT SPEAKER OUTPUT

Connection

WARNING

Remove the ignition key and disconnect the negative · terminal of the battery to prevent short circuits.

CAUTION

• If sound is not output normally, immediately turn power off and check connections.

• Be sure to turn the power off before changing the setting of any switch.

• If the fuse blows, check wires for shorts, then replace the fuse with one of the same rating.

• Check that no unconnected wires or connectors are touching the car body. Do not remove caps from unconnected wires or connectors to prevent short circuits.

• Connect the speaker wires to appropriate speaker connectors separately. Sharing the negative wire of the speaker or grounding speaker wires to the metal body of the car can cause this unit to fail.

• After installation, check that the brake lamps, winkers, and wipers work properly.

* Commercially available parts

Hexagon Wrench (Small)

Use the attached Hexagon Wrench.

Protective Fuse*

Power control wire*

Hexagon Wrench (Large)

Battery wire*

Terminal cover

CENTER UNIT (CD receiver, etc.)

RCA cable*

Hexagon Wrench (Small)

Left input

Right input

Use the attached Hexagon Wrench.

Subwoofer (L + R) (≥2Ω)

WARNING

To prevent fire caused by a short in the wiring, connect a fusible link or breaker nearby the battery’s positive terminal.

About the Lead Terminals

1. Wire Thicknesses

You can use wires with the following thicknesses:

Battery wire and ground wire AWG 4 – AWG 6 Speaker wire AWG 8 – AWG 12

2. Strip the wire

Make a cut in the wire sheath (insulator made from vinyl, etc.) at the position 10-13 mm away from the end of the wire, and then remove the unnecessary portion of the sheath by twisting it.

3. Install the wire

Loosen the screw using the supplied hexagon wrench. Insert the conductor of the wire in the terminal hole, and then tighten the screw.

Battery

Ground wire*

10 - 13 mm (3/8" - 1/2")

Dual voice coil subwoofer

Hexagon Wrench (Large)

When two subwoofers are connected. (≥4Ω)

(2Ω + 2Ω)(4Ω + 4Ω)

Hexagon Wrench (Small)

P.CON SPEAKER OUTPUT

REMOTE

GNDBATT.

LINE IN LINE OUT

P.CON SPEAKER OUTPUT

REMOTE

GNDBATT.

LINE IN LINE OUT

P.CON SPEAKER OUTPUT

REMOTE

GNDBATT.

LINE IN LINE OUT

FUSE[30Ax3

]

FUSE[30Ax3

]

FUSE[30Ax3

]

INPUT

SENSITIVITY[V

]

0.2

[

MAX

]

0.3

0.5

[

MIN

]

LINE OUT

FILTER

OFF

INPUT

SENSITIVITY[V

]

0.2

[

MAX

]

0.3

0.5

[

MIN

]

LINE OUT

FILTER

OFF

INPUT

SENSITIVITY[V

]

0.2

[

MAX

]

0.3

0.5

[

MIN

]

LINE OUT

FILTER

OFF

■ Remote cable connection (Optional accessory)

P.CON SPEAKER OUTPUT

REMOTE

FUSE [30Ax3

]

GNDBATT.

LINE IN LINE OUT

CAUTION

• Before connecting the remote controller cables, always turn the Bass boost level knob all the way to the left.

■ Multi Amplifier with Remote cable connection (Optional accessory)

You can control the Bass boost level of the second and subsequent Slave amplifiers simultaneously from the Master amplifier. The volume level of each amplifier is determined by the setting of the Master amplifier (INPUT SENSITIVITY, boost level of the remote controller).

Setting the Master amplifier

1. Adjust the INPUT SENSIVITY to the output

of the center unit to be connected.

2. Set the LPF frequency and ISF.

3. Turn the LINE OUT FILTER switch ON.

Setting the Slave amplifier

1. Turn the LINE OUT FILTER switch OFF.

2. Adjust the INPUT SENSIVITY.

• To adjust the Slave amplifier to the same volume as the Master amplifier, adjust the INPUT SENSIVITY to 0.2 V (max.).

CENTER UNIT (CD receiver, etc.)

Power control wire*

Master amplifier

Remote cable

Remote controller

Remote cable (6.0 m : 19.7 ft)

RCA cable*

Remote controller

CAUTION

• Before connecting the remote controller cables, always turn the Bass boost level knob all the way to the left.

* Commercially available parts

Hexagon Wrench (Small)

Extension wire*

Slave amplifier

Use the attached Hexagon Wrench.

RCA cable*

English 5

6 English

Controls

P.CON SPEAKER OUTPUT

REMOTE

FUSE[30Ax3

]

GNDBATT.

LINE IN LINE OUT

THERMAL MANAGEMENT PROTECTION

INPUT

SENSITIVITY[V

]

ISF

FREQUENCY[Hz

]

LPF

FREQUENCY[Hz

]

0.2

[

MAX

]

0.3

0.5

200

LINE OUT

FILTER

OFF

150

100

4015

[

MIN

]

    



  

 



 

 Z





NOTE

The control panel locates under the front side cover. Remove the cover to access to its controls for adjustment. (See page 3)

Remote controller (

Optional accessory

)

1 Fuse (30 A × 3)

NOTE

If you can’t find the specified capacity fuse at your store etc., consult your Kenwood dealer.

2 Battery terminal 3 Power control terminal

Controls the unit ON/OFF.

NOTE

Controls the unit power. Be sure to connect it with all the systems.

4 Ground terminal 5 Speaker output terminals

As this unit accepts speakers with a minimum impedance of 1 ohm, connect speakers with 1-ohm or higher impedance to these terminals.

6 REMOTE terminal

Connects the Remote cable.

NOTE

Use the Remote cable of the optional accessory.

7 LINE IN terminal 8 LINE OUT terminal

The audio signal set with the LINE OUT FILTER switch will be output.

9 BOOST LEVEL (Bass boost level) control

Sets the level by which the low frequency range should be boosted.

0 Power indicator

- FREQUENCY (Bass boost frequency) control

Sets the center frequency around which the low frequency range should be boosted.

= THERMAL MANAGEMENT indicator

Lights this indicator when the internal temperature is high.

~ PROTECTION indicator

Lights this indicator when the protection function is activated. (See page 2)

! Power indicator

When the power is turned on, the Power indicator lights.

@ LPF(Low-Pass Filter) FREQUENCY control

This control adjusts the frequency band output from this unit.

# ISF (infrasonic filter) control

Ultralow frequencies that cannot be reproduced even by a subwoofer speaker do not become sound but become unnecessary oscillations, which affect the sound by causing distortion, etc. Setting this control cuts the frequencies below the respective frequency. This improves the reproduction performance of the speakers by eliminating unnecessary oscillations which will not become sound.

$ INPUT SENSITIVITY control

Set this control according to the pre-output level of the center unit connected with this unit.

NOTE

For the pre-output level, refer to the <Specifications> in the instruction manual of the center unit.

% LINE OUT FILTER switch

Changing over the audio signal output to the LINE OUT terminal.

ON position:

The audio signal adjusted when setting LPF, INPUT SENSIVITY control and Bass boost (optional accessory) is output to the LINE OUT terminal.

OFF position:

The audio signal input from the LINE IN terminal is output to the LINE OUT terminal (through output).

CAUTION

The volume of the audio output to the LINE OUT terminal is different in ON and OFF position. Remember this when changing the LINE OUT FILTER switch from ON to OFF.

+ 14 hidden pages