Kenwood TK-3301 Operation Manual [it]

INSTRUCTION MANUAL MODE D’EMPLOI MANUAL DE INSTRUCCIONES MANUALE DI ISTRUZIONI BEDIENUNGSANLEITUNG GEBRUIKSAANWIJZING KULLANIM KILAVUZU

TK-3301

UHF FM TRANSCEIVER ÉMETTEUR-RÉCEPTEUR FM UHF TRANSCEPTOR FM UHF RICETRASMETTITORE FM UHF UHF-FM-TRANSCEIVER UHF FM ZENDONTVANGER

UHF FM EL TELSİZİ

TK-3301

UHF FM TRANSCEIVER

INSTRUCTION MANUAL

ENGLISH

This equipment complies with the essential requirements of Directive 1999/5/EC.

THANK YOU

We are grateful for your purchase of this

Kenwood

welcome you to the Private Mobile Radio service (PMR 446). PMR is a mobile communication system for both business and personal use without the need for a license and with no call charges.

You r

Kenwood

2-way Private Radio is called a “transceiver”, meaning “transmitter & receiver”. We believe this easy-touse transceiver will provide you with dependable and reliable communications. This

Kenwood

transceiver is a precision device. Treat it with care, and you will enjoy years of reliable operation.

product and

FEATURES

• 16 channels with 8 operating frequencies and 38 tone/ code

settings for each channel allows you to ignore unwanted calls.

• Built in voice scrambler gives you complete privacy for your

conversations.

• Hands free operation when using an optional headset.

• Voice announcement lets you know which channel you

have selected and which settings you have made when reassigning key functions and channel settings.

OPERATING CONDITIONS

Open locations (no obstructions) Up to 6.4 km Residential areas (near buildings) Up to 2.4 km In steel/ concrete reinforced buildings Up to 18,580 m In high rises Up to 15 floors

Note: The listed ranges are based on field testing and may vary with your operating conditions and individual transceiver.

NOTICES TO THE USER

Government law prohibits the operation of unlicensed radio

◆

transmitters within the territories under government control.

Illegal operation is punishable by fine and/or imprisonment.

◆

Refer service to qualified technicians only.

◆

Safety:

It is important that the operator is aware of, and understands, hazards common to the operation of any transceiver.

Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for EU countries that have adopted separate waste collection systems)

Products and batteries with the symbol (crossed-out wheeled bin) cannot be

disposed as household waste. Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details in locating a recycle facility nearest to you. Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment.

Notice: The sign "Pb" below the symbol for batteries indicates that this

battery contains lead.

Firmware Copyrights

The title to and ownership of copyrights for firmware embedded in Kenwood product memories are reserved for

Corporation

JVC KENWOOD

PRECAUTIONS

• Do not charge the transceiver and battery pack when they are wet.

• Ensure that there are no metallic items located between the

transceiver and the battery pack.

• Do not use options not specified by

• If the die-cast chassis or other transceiver part is damaged, do not

touch the damaged parts.

• If a headset or headphone is connected to the transceiver, reduce

the transceiver volume. Pay attention to the volume level when turning the squelch off.

• Do not place the microphone cable around your neck while near

machinery that may catch the cable.

• Do not place the transceiver on unstable surfaces.

• Ensure that the end of the antenna does not touch your eyes.

• When the transceiver is used for transmission for many hours, the

radiator and chassis will become hot. Do not touch these locations when replacing the battery pack.

• Do not immerse the transceiver in water.

• Always switch the transceiver power off before installing optional

accessories.

• The charger is the device that disconnects the unit from the AC

mains line. The AC plug should be readily accessible.

Kenwood

Turn the transceiver power off in the following locations:

• In explosive atmospheres (inflammable gas, dust particles, metallic powders, grain powders, etc.).

• While taking on fuel or while parked at gasoline service stations.

• Near explosives or blasting sites.

• In aircrafts. (Any use of the transceiver must follow the instructions and regulations provided by the airline crew.)

• Where restrictions or warnings are posted regarding the use of radio devices, including but not limited to medical facilities.

• Near persons using pacemakers.

• Do not disassemble or modify the transceiver for any reason.

• Do not place the transceiver on or near airbag equipment while the vehicle is running. When the airbag inflates, the transceiver may be ejected and strike the driver or passengers.

• Do not transmit while touching the antenna terminal or if any metallic parts are exposed from the antenna covering. Transmitting at such a time may result in a high-frequency burn.

• If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, remove the battery pack from the transceiver, and contact your dealer.

• Use of the transceiver while you are driving may be against traffic laws. Please check and observe the vehicle regulations in your area.

• Do not expose the transceiver to extremely hot or cold conditions.

• Do not carry the battery pack (or battery case) with metal objects, as they may short the battery terminals.

• Danger of explosion if the battery is incorrectly replaced; replace only with the same type.

• When operating the transceiver in areas where the air is dry, it is easy to build up an electric charge (static electricity). When using an earphone accessory in such conditions, it is possible for the transceiver to send an electric shock through the earphone and to your ear. We recommend you use only a speaker/microphone in these conditions, to avoid electric shocks.

Kenwood

iii

Information concerning the battery pack:

The battery pack includes flammable objects such as organic solvent. Mishandling may cause the battery to rupture producing flames or extreme heat, deteriorate, or cause other forms of damage to the battery. Please observe the following prohibitive matters.

•

Do not disassemble or reconstruct battery!

The battery pack has a safety function and protection circuit to

avoid danger. If they suffer serious damage, the battery may generate heat or smoke, rupture, or burst into flame.

•

Do not short-circuit the battery!

Do not join the + and – terminals using any form of metal (such

as a paper clip or wire). Do not carry or store the battery pack in containers holding metal objects (such as wires, chain-necklace or hairpins). If the battery pack is short-circuited, excessive current will flow and the battery may generate heat or smoke, rupture, or burst into flame. It will also cause metal objects to heat up.

•

Do not incinerate or apply heat to the battery!

If the insulator is melted, the gas release vent or safety function is

damaged, or the electrolyte is ignited, the battery may generate heat or smoke, rupture, or burst into flame.

•

Do not use or leave the battery near fire, stoves, or other heat generators (areas reaching over 80°C/ 176°F)!

If the polymer separator is melted due to high temperature, an

internal short-circuit may occur in the individual cells and the battery may generate heat or smoke, rupture, or burst into flame.

•

Do not immerse the battery in water or get it wet by other means!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into flame.

•

Do not charge the battery near fire or under direct sunlight!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into flame.

•

Use only the specified charger and observe charging requirements!

If the battery is charged in unspecified conditions (under high

temperature over the regulated value, excessive high voltage or current over regulated value, or with a remodeled charger), it may overcharge or an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into flame.

•

Do not pierce the battery with any object, strike it with an instrument, or step on it!

This may break or deform the battery, causing a short-circuit. The

battery may generate heat or smoke, rupture, or burst into flame.

•

Do not jar or throw the battery!

An impact may cause the battery to leak, generate heat or smoke,

rupture, and/or burst into flame. If the battery’s protection circuit is damaged, the battery may charge at an abnormal current (or voltage), and an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into flame.

•

Do not use the battery pack if it is damaged in any way!

The battery may generate heat or smoke, rupture, or burst into

flame.

•

Do not solder directly onto the battery!

If the insulator is melted or the gas release vent or safety function

is damaged, the battery may generate heat or smoke, rupture, or burst into flame.

•

Do not reverse the battery polarity (and terminals)!

When charging a reversed battery, an abnormal chemical reaction

may occur. In some cases, an unexpected large amount of current may flow upon discharging. The battery may generate heat or smoke, rupture, or burst into flame.

•

Do not reverse-charge or reverse-connect the battery!

The battery pack has positive and negative poles. If the battery

pack does not smoothly connect with a charger or operating equipment, do not force it; check the polarity of the battery. If the battery pack is reverse-connected to the charger, it will be reversecharged and an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into flame.

•

Do not touch a ruptured and leaking battery!

If the electrolyte liquid from the battery gets into your eyes, wash

your eyes with fresh water as soon as possible, without rubbing your eyes. Go to the hospital immediately. If left untreated, it may cause eye-problems.

•

Do not charge the battery for longer than the specified time!

If the battery pack has not finished charging even after the

regulated time has passed, stop it. The battery may generate heat or smoke, rupture, or burst into flame.

•

Do not place the battery pack into a microwave or high pressure container!

The battery may generate heat or smoke, rupture, or burst into

flame.

•

Keep ruptured and leaking battery packs away from fire!

If the battery pack is leaking (or the battery emits a bad odor),

immediately remove it from flammable areas. Electrolyte leaking from battery can easily catch on fire and may cause the battery to generate smoke or burst into flame.

•

Do not use an abnormal battery!

If the battery pack emits a bad odor, appears to have different

coloring, is deformed, or seems abnormal for any other reason, remove it from the charger or operating equipment and do not use it. The battery may generate heat or smoke, rupture, or burst into flame.

CONTENTS

UNPACKING AND CHECKING EQUIPMENT .......................... 1

PREPARATION .......................................................... 2

ORIENTATION ........................................................... 6

BASIC OPERATIONS ................................................... 8

VOICE OPERATED TRANSMISSION (VOX) .......................... 9

BACKGROUND OPERATIONS ........................................ 10

CHANNEL SETUP MODE .............................................. 11

KEY ASSIGNMENT MODE ............................................17

TROUBLESHOOTING GUIDE .........................................21

OPTIONAL ACCESSORIES ............................................ 22

UNPACKING AND CHECKING EQUIPMENT

Carefully unpack the transceiver. If any of the items listed below are missing or damaged, file a claim with the carrier immediately.

SUPPLIED ACCESSORIES

• Battery charger/ AC adapter (KSC-35 or KSC-35S) ............... 1

• Li-ion Battery pack (KNB-45L) ................................................1

• Speaker/ microphone jack cover ............................................1

• Speaker/ microphone locking bracket ....................................1

• Belt clip (KBH-10) ...................................................................1

• Screw set

• M2.6 x 7 mm (Black) ............................................................... 1

• M3 x 8 mm .............................................................................. 2

• Instruction manual ..................................................................1

Note: Refer to "PREPARATION" for accessory installation instructions.

PREPARATION

INSTALLING/ REMOVING THE BATTERY PACK

◆ Do not short the battery terminals or dispose of the battery by fire.

◆ Never attempt to remove the casing from the battery pack.

1 Align the battery pack with the

back of the transceiver, then press the battery pack and transceiver firmly together until the release latch on the base of the transceiver locks.

2 To remove the battery pack, lift

the safety catch on the base of the transceiver, then press the release latch underneath the safety catch.

3 While pressing the release

latch, pull the battery pack away from the transceiver.

INSTALLING THE BELT CLIP

If necessary, attach the belt clip using the two supplied M3 x 8 mm screws.

Note: If the belt clip is not installed, its mounting location may get hot during continuous transmission or when left sitting in a hot environment.

Belt clip

Do not use glue which is designed to prevent screw loosening when installing the belt clip, as it may cause damage to the transceiver. Acrylic ester, which is contained in these glues, may crack the transceiver’s back panel.

INSTALLING THE COVER OVER THE SPEAKER/ MICROPHONE JACKS

If you are not using a speaker/ microphone, install the cover over the speaker/ microphone jacks using the supplied M2.6 x 7 mm screw.

Note: To keep the transceiver water resistant, you must cover the speaker/ microphone jacks with the supplied cover.

Speaker/ microphone

jack cover

INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE (OR HEADSET)

1 Insert the speaker/ microphone

(or headset) plugs into the speaker/ microphone jacks.

2 Attach the locking bracket using

the supplied M2.6 x 7 mm screw.

Note: The transceiver is not fully water resistant while using the speaker/ microphone.

Speaker/ microphone

locking bracket

CHARGING THE BATTERY PACK

The battery pack is not charged at the factory; charge it before use.

Average battery pack life (calculated using 5% transmit time, 5% receive time, and 90% standby time) is 20 hours.

ATTENTION: Always switch OFF a transceiver equipped with a battery pack before inserting the transceiver into the charger.

1 Plug the AC adapter cable into

the jack located on the rear of the charger.

2 Plug the AC adapter into an AC

outlet.

3 Slide a battery pack or a

transceiver equipped with a battery pack into the charging slot of the charger.

• Make sure the metal contacts of the battery pack mate securely with the charger terminals.

• The indicator lights red and

Charging slot

charging begins.

4 When charging is completed, the

Indicator

indicator lights green. Remove the battery pack or the transceiver from the charging slot of the charger.

• It takes approximately 3 hours to charge the battery pack.

• When the charger will not be used for a long time, unplug the AC adapter from the AC outlet.

Note:

◆ When the indicator blinks red, the battery pack is either defective or the battery pack contacts are not properly mated with those of the charger.

◆ When the indicator flashes green and orange, the battery pack has not satisfied the charging start temperature. Remove the battery pack from the charger and wait until it reaches a normal temperature before charging it again. <KSC-35S only>

◆ The ambient temperature should be between 5°C and 40°C while charging is in progress. Charging outside this range may not fully charge the battery.

◆ The battery pack life is over when its operating time decreases even though it is fully and correctly charged. Replace the battery pack.

ORIENTATION

Antenna

Battery pack

Channel selector

Rotate to change the operating channel.

• To change the operating frequency or QT/DQT settings of a channel, refer to “CHANNEL SETUP MODE” on page 11.

• Channel Annunciation: When changing channels, the transceiver will announce the newly selected channel number. (This can be deactivated by your dealer.)

LED indicator

For the LED indicator status, refer to page 7.

Power switch/ Volume control

Turn clockwise to switch the transceiver ON. To switch the

transceiver OFF, turn counterclockwise until a click sounds. Rotate to adjust the volume level.

PTT (Push to Talk) switch

Press and hold, then speak into the microphone to transmit.

Side 1 key Press to activate its programmable function. The default setting is Calling Alert.

• For function descriptions and details on how to change the function of the Side 1 key, refer to “KEY ASSIGNMENT MODE” on page 17.

Side 2 key Press to activate its programmable function. The default setting is Squelch Off Momentary.

• For function descriptions and details on how to change the function of the Side 2 key, refer to “KEY ASSIGNMENT MODE” on page 17.

Speaker/ microphone jacks

Insert the Speaker/ microphone or Headset plug into this

jack.

LED Indicator Status

Indicator Color Meaning

Lights red Transmitting Lights green Receiving a call Blinks red Battery power is low while transmitting Blinks green Scanning

Blinks red/orange

The selected channel has not been programmed and cannot be used.

BASIC OPERATIONS

1 Turn the Power switch/ Volume control

clockwise to switch the transceiver power ON.

• A beep sounds if enabled by your dealer.

2 Press the key programmed with the Monitor

or Squelch Off (Side 2 key default) function to hear background noise, then rotate the Power switch/ Volume control to adjust the volume.

3 Rotate the Channel selector to select your

desired channel.

• When you receive an appropriate signal, you will hear audio from the speaker.

4 To make a call, press and hold the PTT

switch, then speak into the microphone using your normal speaking voice.

• Hold the microphone approximately 3 to 4 cm (1.5 inches)from your lips.

5 Release the PTT switch to receive.

Note: When the battery pack voltage becomes too low, transmission

will stop and an alert tone will sound.

VOICE OPERATED TRANSMISSION (VOX)

VOX operation allows you to transmit hands-free. VOX can only be used if you are using a supported headset. This function can be turned off for specific channels by your dealer.

To activate VOX and set the VOX Gain level, perform the following steps:

1 Connect the headset to the transceiver .

• The VOX function does not activate when a headset is not connected to the accessory terminal of the transceiver.

2 With the transceiver power OFF, press and hold the Side 1

key while turning the transceiver power ON.

3 Continue to hold the Side 1 key until a beep sounds.

• The LED indicator lights turn orange.

• When the Side 1 key is released, the transceiver will announces the VOX Gain level.

4 Press the Side 1 key to increase the VOX Gain level and

the Side 2 key to decrease the level.

• The VOX Gain level can be adjusted from level 1 to 10 and OFF.

• The transceiver announces the VOX Gain level as you adjust it. If OFF is selected, a beep sounds.

5 Press the PTT switch to save the setting.

• A beep will sound.

• The transceiver announces the new VOX Gain level.

6 Turn the transceiver power OFF and then ON again to

activate VOX.

Note:

◆ If a headset is connected to the transceiver while the VOX function is switched ON and the VOX Gain level is configured to a higher, more sensitive level, louder received signals may cause the transceiver to start transmission.

◆ The transceiver will automatically return to normal operation if no action is performed for 5 seconds.

BACKGROUND OPERATIONS

TIME-OUT TIMER (TOT)

The Time-out Timer prevent callers from using a channel for an extended duration. If you continuously transmit for the duration programmed by your dealer (default is 60 seconds), transmission will stop and an alert tone will sound. To stop the tone, release the PTT switch.

BATTERY SAVER

When activated by your dealer, the Battery Saver function decreases the amount of power used after no signal is present and no operations are being performed for 5 seconds. When a signal is received or an operation is performed, Battery Saver turns off.

Note: While the Battery Saver is operating, the LED may flash green when receiving a QT/DQT signal which does not match the QT/DQT tone/code set up in your transceiver.

LOW BATTERY WARNING

While operating the transceiver, the Low Battery Warning sounds an alert tone every 30 seconds and the LED indicator blinks red when the battery needs recharged or replaced.

CHANNEL ANNUNCIATION

When changing the channel, the transceiver will announce the newly selected channel number. Likewise, the transceiver will announce the current channel after you turn the transceiver power ON. (Channel Annunciation can be activated or deactivated by your dealer.)

CHANNEL SETUP MODE

This transceiver allows you to reprogram each of the channels with different frequencies and QT (Quiet Talk)/ DQT (Digital Quiet Talk) settings. The table below lists the default channel settings.

Channel Number

Note: You must first select an operating frequency for a channel

before you can select a QT/ DQT setting for that same channel.

Table

Number

Frequency (MHz)

1 446.00625 10 94.8 Hz 8 446.09375 08 88.5 Hz 3 446.03125 13 103.5 Hz 6 446.06875 05 79.7 Hz 4 446.04375 17 118.8 Hz 2 446.01875 18 123.0 Hz 7 446.08125 19 127.3 Hz 5 446.05625 07 85.4 Hz 1 446.00625 14 107.2 Hz 8 446.09375 15 110.9 Hz 3 446.03125 16 114.8 Hz 6 446.06875 06 82.5 Hz 4 446.04375 27 D132N 2 446.01875 28 D155N 5 446.05625 29 D134N 7 446.08125 30 D243N

Ton e

Number

QT/DQT Setting

CHANNEL OPERATING FREQUENCIES

To change the operating frequency of a channel: 1 With the transceiver power OFF, press and hold the PTT

switch and Side 1 key while turning the transceiver power ON.

• Continue to hold the PTT switch and Side 1 key until the LED lights orange and the transceiver announces “Self”.

2 Release the PTT switch and Side 1 key.

• The transceiver announces “Channel”.

3 Press and release the PTT switch, then rotate the Channel

selector to your desired channel.

• Upon pressing and releasing the PTT switch, a beep will sound and the transceiver announces “Table zero”.

4 Press the Side 1 or Side 2 key to increment/ decrement the

Table number, to select the new channel frequency.

• Table numbers and their corresponding operating frequencies are provided in the table on page 13.

• A voice announcement will inform you of the currently selected Table number.

5 Press the PTT switch to save the setting.

• A beep will sound.

• Repeat steps 3 to 5 to set up another channel.

6 Turn the transceiver power OFF and then ON again to

activate the new settings.

Note: The transceiver will automatically return to normal operation if no action is performed for 5 seconds.

Table Number

Operating

Frequency

OFF

446.00625 MHz

446.01875 MHz

446.03125 MHz

446.04375 MHz

Table Number

Operating

Frequency

446.05625 MHz

446.06875 MHz

446.08125 MHz

446.09375 MHz

QT/ DQT SETTINGS

Quiet Talk (QT) and Digital Quiet Talk (DQT) are functions that reject undesired signals on your channel. You will hear a call only when you receive a signal that contains a matching QT tone or DQT code. If a call containing a different tone or code is received, squelch will not open and you will not hear the call. Likewise, when transmitting using QT or DQT, the receiving station must have a matching tone or code to hear your call.

Be aware that other parties can still hear your calls if they set up their transceiver with the same tone or code.

The default QT/DQT settings for each channel are provided in the table on page 15.

To change the QT/DQT settings of a channel: 1 With the transceiver power OFF, press and hold the PTT

switch and Side 1 key while turning the transceiver power ON.

• Continue to hold the PTT switch and Side 1 key until the LED lights orange and the transceiver announces “Self”.

2 Release the PTT switch and Side 1 key.

• The transceiver announces “Channel”.

3 Press the Side 1 or Side 2 key to select QT/DQT setup.

• The transceiver announces “Tone”.

4 Press and release the PTT switch, then rotate the Channel

selector to your desired channel.

• Upon pressing and releasing the PTT switch, a beep will sound and the transceiver announces “Tone one”.

5 Press the Side 1 or Side 2 key to increment/ decrement the

Tone number, to select the new tone or code.

• QT/DQT table numbers and their corresponding tones/ codes are provided in the table on page 15.

• Press and hold the Side 1 or Side 2 key to increment/ decrement the Tone number by 5 at a time.

• A voice announcement will inform you of the currently selected Tone number.

6 Press the PTT switch to save the setting.

• A beep will sound.

• Repeat steps 4 to 6 to set up another channel.

7 Turn the transceiver power OFF and then ON again to

activate the new settings.

Note: The transceiver will automatically return to normal operation if no action is performed for 5 seconds.

Tone

Number

Note: The Tone numbers corresponding to the QT/DQT values can

be changed by your dealer.

QT/DQT

Setting

67.0 Hz

71.9 Hz

74.4 Hz

77.0 Hz

79.7 Hz

82.5 Hz

85.4 Hz

88.5 Hz

91.5 Hz

94.8 Hz

97.4 Hz

100.0 Hz

103.5 Hz

Tone

Number

QT/DQT

Setting

107.2 Hz

110.9 Hz

114.8 Hz

118.8 Hz

123.0 Hz

127.3 Hz

131.8 Hz

136.5 Hz

141.3 Hz

146.2 Hz

151.4 Hz

156.7 Hz

162.2 Hz

Tone

Number

Off

QT/DQT

Setting

D132N D155N D134N D243N D311N D346N D315N D351N D423N D664N D431N D723N

OFF

CHANNEL CONFIRMATION MODE

To confirm your channel settings: 1 With the transceiver power OFF, press and hold the PTT

switch while turning the transceiver power ON.

• Continue to hold the PTT switch until the LED lights orange and the transceiver announces “Confirm”.

2 Release the PTT switch.

• The transceiver announces the channel table number and Tone number of the selected channel.

3 Rotate the Channel selector to your desired channel within

5 seconds, otherwise the operation will cancel.

• The transceiver announces the channel table number and Tone number of the current channel.

Note: The transceiver will automatically return to normal operation if no action is performed for 5 seconds.

KEY ASSIGNMENT MODE

This transceiver allows you to reprogram the Side 1 and Side 2 keys with any of the functions listed in the table below.

Explanations on the use of each function are provided under “PROGRAMMABLE FUNCTIONS”, on page 19.

Table Number Function Name

None (no function) Calling Alert ( Key Lock Key Lock Status Memory Monitor Monitor Momentary Scan Scan + Temporary Delete Scrambler Squelch Off Squelch Off Momentary ( Temporary Delete

Side 1

key default)

Side 2

key default)

To change the functions of the Side 1 and Side 2 keys: 1 With the transceiver power OFF, press and hold the Side 1

and Side 2 keys while turning the transceiver power ON.

• Continue to hold the Side 1 and Side 2 keys until the LED lights orange and the transceiver announces “Setup”.

2 Continue to press and hold the key to be reprogrammed

(either the Side 1 or Side 2 key), while releasing the remaining key.

• The transceiver will announce “Table zero”.

• If you continue to hold both keys, or if you release both keys, the operation will cancel in 5 seconds.

3 Release the key. 4 Press the Side 1 or Side 2 key to increment/ decrement the

number, to select the new key function.

• Table numbers and their corresponding functions are provided in the table on page 17.

• A voice announcement will inform you of the currently selected Table number.

5 Press the PTT switch to save the setting.

• A beep will sound and the transceiver will announce the new Table number.

6 Turn the transceiver power OFF and then ON again to

activate the new settings.

Note: The transceiver will automatically return to normal operation if no action is performed for 5 seconds.

PROGRAMMABLE FUNCTIONS

Calling Alert (Side 1

■

Calling alert tones help identify yourself to party members and inform them that you are calling. Your dealer can set up your transceiver with 1 of 10 calling alert tones. If each party member uses a different tone, it is easy to know who is calling. To make a call, press and hold the PTT switch, then press the key programmed as Calling Alert.

• Release the key to end the tone.

Key Lock

■

Press and hold this key for 1 second to lock/ unlock the transceiver keys. The following keys/ functions can still be used when Key Lock is active:

Calling Alert, Key Lock, Monitor, Monitor Momentary, PTT, Squelch Off, Squelch Off Momentary, and Volume.

Key Lock with Status Memory

■

This operates the same as Key Lock except that when the transceiver power is turned OFF and then ON again, the keys remain locked. Without Status Memory, when the transceiver power is turned OFF and then ON again, the Key Lock function will be cancelled.

Monitor

■

Momentarily press this key to deactivate QT or DQT signaling. Press the key again to return to normal operation.

Monitor Momentary

■

Press and hold this key to deactivate QT or DQT signaling. Release the key to return to normal operation.

key default)

Scan

■

Press this key to start scanning the transceiver channels. Priority Scan: The Priority channel is a channel that is given first priority to while scanning. The Priority channel is set by your dealer. Revert Channel: During Scan, pressing the PTT switch will automatically select the transceiver’s Revert channel and you will begin transmitting. Your dealer can program the Revert channel using one of the following methods:

• Selected

• Selected + Talkback

• Priority

• Priority + Talkback

Scan + Temporary Delete

■

Press this key to start scanning the transceiver channels. When Scan pauses at an undesired channel, you can remove that channel from the scanning sequence by pressing and holding this key for 3 seconds.

Scrambler

■

The Scrambler function allows you to hold a conversation in complete privacy. When the Scrambler function is activated, any other party that is listening to your channel will be unable to understand your conversation.

Squelch Off

■

Momentarily press this key to hear background noise. Press the key again to return to normal operation.

Squelch Off Momentary (Side 2

■

Press and hold this key to hear background noise. Release the key to return to normal operation.

Temporary Delete

■

When Scan pauses at an undesired channel, you can remove that channel from the scanning sequence by pressing and holding this key for 1 second.

key default)

+ 186 hidden pages