This TK-3217(C, C2) service manual contains a number
of sections which differ from the service manual (B518744-00) for the TK-3217(C).
For items other than those in this TK-3217(C, C2) service manual please refer to the service manual (B518744-00) for the TK-3217(C).
Copyright 2007 by Kenwood Corporation. All rights reserved.
No part of this manual may be reproduced, translated,
distributed, or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
for any purpose without the prior written permission of
Kenwood.
While every precaution has been taken in the preparation
of this manual, Kenwood assumes no responsibility for errors
or omissions. Neither is any liability assumed for damages
resulting from the use of the information contained herein.
Kenwood reserves the right to make changes to any products
herein at any time for improvement purposes.
GENERAL / 概述
INTRODUCTION
SCOPE OF THIS MANUAL
This manual is intended for use by experienced technicians
familiar with similar types of commercial grade
communications equipment. It contains all required service
information for the equipment and is current as of the
publication date. Changes which may occur after publication
are covered by either Service Bulletins or Manual Revisions.
These are issued as required.
ORDERING REPLACEMENT PARTS
When ordering replacement parts or equipment information,
the full part identification number should be included. This
applies to all parts : components, kits, or chassis. If the part
number is not known, include the chassis or kit number of
which it is a part, and a sufficient description of the required
component for proper identification.
The following precautions are recommended for personal
safety:
• DO NOT transmit until all RF connectors are verified secure
and any open connectors are properly terminated.
• SHUT OFF and DO NOT operate this equipment near
electrical blasting caps or in an explosive atmosphere.
• This equipment should be serviced by a qualified technician only.
SERVICE
This transceiver is designed for easy servicing. Refer to
the schematic diagrams, printed circuit board views, and
alignment procedures contained within.
A personal computer (IBM PC or compatible), programming
interface (KPG-22/22A), and programming software (KPG-100D(C))
are required for programming.
(The frequency, TX power HI/LOW, and signaling data are programmed
for the transceiver.)
"Clone Mode" copies the transceiver data to another
transceiver.
The dealer can copy the transceiver data to another
transceiver even without the use of a personal computer.
1-2. Example
The transceiver can copy the programming data to one or
more transceivers via RF communication.
The clone source and clone target/s must be in Clone mode.
1-3. Operation
1. To switch the clone target/s to Clone mode, press and hold
the [<B] key while turning the transceiver power ON.
2. Wait for 2 seconds. “CLONE” appears on the LCD, followed
by “FRQTBL 1”.
3. Select a channel table number using the [Selector] knob.
4. To switch the clone source to Clone mode, press and hold
the [<B] key while turning the transceiver power ON.
5. Wait for 2 seconds. “CLONE” appears on the LCD, followed
by “FRQTBL 1”.
6. Select the same channel table number as the clone target/s.
7. Press the [S] key on the clone source to begin data
transmission. When the clone target starts to receive data,
the green LED will light and “CLONING” will appear on
the LCD. The source unit will display “MASTER”.
8. When the clone source finishes sending data, a
“confirmation” tone will sound and “COMPLETE” will
appear on the LCD. If data transmission failed while cloning,
the target unit will produced an error tone and “CLONE
NG” will appear on the LCD.
9. If the cloning fails, no data will be available in the target
unit when it is returned to User mode.
10.When the cloning is successful, the target unit's "Scan"
and "Key lock" functions will return to their default values
(Scan = OFF, Key lock = OFF).
11.The source will remain in clone mode after cloning. The target
unit will return to user mode after a successful cloning.
模式组合
1. 复制模式
1-1. 概要
“复制模式”可以将一台对讲机数据复制到其它的对讲机。
经销商甚至不使用个人电脑也可以将一台对讲机的数据复制
到其它的对讲机。
1-2. 例
对讲机可以通过 RF 通信将编程数据复制到一台或更多的对
讲机。
复制主机和复制子机必须处于复制模式。
1-3. 操作方法
1. 将子机切换到复制模式,接通(ON)对讲机电源开关的同时,
持续按[<B]键。
2. 等待 2 秒。LCD 上显示“CLONE”,然后显示“FRQTBL 1”。
3. 用[Selector]旋钮选择频率表号码。
4. 将主机切换到复制模式,打开对讲机电源(ON)的同时,持续
按[<B]键。
5. 等待2 秒。在LCD 上显示“CLONE”,然后显示“FRQTBL 1”。
6. 选择与复制子机相同的频率表号码。
7. 按复制主机上的[S]键,开始传输数据。当复制子机开始接收
数据时,绿色 LED 将亮灯,并且“CLONING”显示在 LCD
上。主机将显示出“MASTER”。
• The dealer can clone data to two or more transceivers by
repeating the above procedures.
• If the transceivers Clone Mode is configured as "Disabled",
the transceiver cannot enter Clone mode.
• The table shown below will cover the frequency tables used
for wireless cloning.
• Clone mode cannot be entered in battery low state.
•A unit cannot be a "Source Unit" if it is unprogrammed. If
the [S] key is pressed, an "error" tone will sound.
• Once a unit is set to be the Source, it cannot be a target
after the data has been transmitted. This protects the data
in the Source unit.
• MSK signaling is used in cloning.
4
注∶
• 经销上可以把同样的数据反复地复制到两台或更多的对讲
机。
• 如果对讲机的复制模式被设定为“禁用”,则对讲机不能进入
复制模式。
• 此表是使用于无线复制的频率表。
• 在电池低电压状态时,不能进入复制模式。
• 如果没有被编程,就不能成为“主机”。如果[S]键被按,将
会发出“错误”音。
• 对讲机一旦被设定为主机,而且数据被传送之后,它就不能
成为子机。此功能是为了保护主机内的数据。
• MSK 信号用于复制。
TK-3217
REALIGNMENT /
• Electronic interface may cause a failure in data transfer
during Wireless Clone, such as when waveforms or
electromagnetics are being performed at the workbench.
• Clone mode can be used ONLY by the authorized service
personnel.
• The Clone mode setting must be configured as "Disable"
before being delivered to the end-user.
• To clone, replace the antenna from both the source
transceiver and the target transceiver with a dummy
load.
• The transmit output power is automatically set to Low
in Clone mode.
If the Data password is set to the transceiver, you must
enter the password to activate a clone mode. The maximum
length of the password is 6 digits.
The following describes how to enter the password.
1. Press and hold the [<B] key for 2 seconds while turning
the transceiver power on.
2. “CLN.LOCK.R”(When the Read authorization password is
set to the transceiver.) / “CLN.LOCK.W” (When the
Overwrite password is set to the transceiver.) is displayed
on the LCD.
3. If the [selector] knob is rotated while “CLN.LOCK.R”/
“CLN.LOCK.W” is displayed, the number (0 to 9) flashes
on the LCD.
When you press the [C>] key, the currently selected
number is determined.
If you press the [A] key, the least digit of the password is
deleted.
If you press the [S] key after entering the password in this
procedure, “FRQTBL 1” is displayed if the entered
password is correct.
If the password is incorrect, “CLN.LOCK.R”/
“CLN.LOCK.W” is redisplayed.
Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis.
Teile ohne Parts No. werden nicht geliefert.
402AG53-1661-03PACKING(SP/MIC)
412CH12-3179-05PACKING FIXTURE
431CH25-0085-04PROTECTION BAG (100/200/0.07)
443CH52-2126-02ITEM CARTON CASE
462CJ19-5472-03HOLDER(SP/MIC)ACCESSORY
C132CC73GCH1H390JCHIP C39PFJC2
C133CK73GB1H471KCHIP C470PF K
C134CK73GB1H103KCHIP C0.010UF K
C135CK73GB1C104KCHIP C0.10UF K
C136CK73GB1A105KCHIP C1.0UF K
C67CC73HCH1H040BCHIP C4.0PFBC2
C67CC73HCH1H050BCHIP C5.0PFBC
C68 -70CK73HB1H471KCHIP C470PF K
C71 ,72CK73HB1A104KCHIP C0.10UF K
C73 ,74CC73HCH1H0R5BCHIP C0.5PFB
C75 ,76CK73HB1H102KCHIP C1000PF K
C77CK73HB1H471KCHIP C470PF K
C78CC73HCH1H330JCHIP C33PFJ
C79CS77CP0J100MCHIP TNTL 10UF6.3WV
C80CK73HB1H471KCHIP C470PF K
C83CC73HCH1H150JCHIP C15PFJ
C84 -86CK73HB1H102KCHIP C1000PF K
C87CC73HCH1H100DCHIP C10PFD
C88CC73HCH1H010BCHIP C1.0PFBC2
C90CK73HB1H102KCHIP C1000PF K
C190CK73GB1A105KCHIP C1.0UF K
C191CK73GB1H103KCHIP C0.010UF K
C201CK73GB1A224KCHIP C0.22UF K
C206CK73HB1H102KCHIP C1000PF K
C207CK73HB1H182KCHIP C1800PF K
C100CK73HB1H471KCHIP C470PF K
C101CK73GB1H471KCHIP C470PF K
C102CC73GCH1H120JCHIP C12PFJ
C106CK73HB1H471KCHIP C470PF K
C107CC73GCH1H060BCHIP C6.0PFBC
C107CC73GCH1H070BCHIP C7.0PFBC2
C108CK73HB1H471KCHIP C470PF K
C110,111CK73GB1H471KCHIP C470PF K
C112CC73GCH1H070DCHIP C7.0PFD
C113CK73GB1C104KCHIP C0.10UF K
C127CC73GCH1H200JCHIP C20PFJC
C128CK73HB1H471KCHIP C470PF K
C129CK73GB1H471KCHIP C470PF K
C130CK73HB1H471KCHIP C470PF K
C132CC73GCH1H240JCHIP C24PFJC
C208CK73HB1H471KCHIP C470PF K
C209CS77CP0J100MCHIP TNTL 10UF6.3WV
C210CK73HB1H471KCHIP C470PF K
C211CK73HB1C103KCHIP C0.010UF K
C213CK73HB1A104KCHIP C0.10UF K
C214CC73HCH1H680JCHIP C68PFJ
C215CK73HB1H102KCHIP C1000PF K
C216CK73GB1C104KCHIP C0.10UF K
C217CK73HB1A104KCHIP C0.10UF K
C218CK73GB1C104KCHIP C0.10UF K
C219CC73HCH1H330JCHIP C33PFJ
C220CK73HB1H102KCHIP C1000PF K
C221CK73GB1C104KCHIP C0.10UF K
C222CK73HB1H102KCHIP C1000PF K
C224,225CK73HB1C103KCHIP C0.010UF K
C228CC73GCH1H120JCHIP C12PFJ
C230CK73HB1C103KCHIP C0.010UF K
C231CK73GB1H103KCHIP C0.010UF K
C232CK73HB1C103KCHIP C0.010UF K
C233CC73GCH1H060BCHIP C6.0PFB
C234CK73HB1H102KCHIP C1000PF K
C236CC73GCH1H180JCHIP C18PFJ
C237CK73HB1H102KCHIP C1000PF K
C238CK73GB1C104KCHIP C0.10UF K
C239CK73GB1H102KCHIP C1000PF K
C325CK73HB1A104KCHIP C0.10UF K
C326CK73HB1H102KCHIP C1000PF K
C327CC73HCH1H101JCHIP C100PF J
C328CK73HB1H391KCHIP C390PF K
C329,330CK73GB1A105KCHIP C1.0UF K
C257CC73GCH1H070BCHIP C7.0PFBC2
C257CC73GCH1H4R5BCHIP C4.5PFBC
C258CK73HB1H471KCHIP C470PF K
C259CK73GB1H471KCHIP C470PF K
C262,263CK73HB1H471KCHIP C470PF K
C265CK73HB1H471KCHIP C470PF K
C266CK73GB1H471KCHIP C470PF K
C267CC73GCH1H040BCHIP C4.0PFBC
C267CC73GCH1H060BCHIP C6.0PFBC2
C268CC73GCH1H220JCHIP C22PFJ
C331CK73HB1A104KCHIP C0.10UF K
C332CK73HB1H471KCHIP C470PF K
C333,334CK73GB1C104KCHIP C0.10UF K
C335CC73GCH1H221JCHIP C220PF J
C336CK73FB1C474KCHIP C0.47UF K
C338CC73GCH1H101JCHIP C100PF J
C339CS77AA0J100MCHIP TNTL10UF6.3WV
C340CK73GB1C104KCHIP C0.10UF K
C341CK73GB1C473KCHIP C0.047UF K
C342CS77AA0J100MCHIP TNTL10UF6.3WV
C343CK73GB1C473JCHIP C0.047UF J
C344CC73GCH1H221JCHIP C220PF J
C345CS77AB20J101MCHIP TAN100UF 6.3WV
C346CK73GB1H102KCHIP C1000PF K
C348CK73HB1H471KCHIP C470PF K
C350CK73HB1H471KCHIP C470PF K
C351,352CK73HB1C103KCHIP C0.010UF K
C354CK73HB1A104KCHIP C0.10UF K
C356CK73HB1A333KCHIP C0.033UF K
C357CK73HB1E472KCHIP C4700PF K
C401CC73GCH1H471JCHIP C470PF J
C402CK73HB1H102KCHIP C1000PF K
C403CK73GB1C104KCHIP C0.10UF K
C405CC73GCH1H101JCHIP C100PF J
C406CK73HB1E472KCHIP C4700PF K
C407CK73HB1H102KCHIP C1000PF K
C408CK73HB1E472KCHIP C4700PF K
C409,410CK73GB1A105KCHIP C1.0UF K
C411CK73HB1H102KCHIP C1000PF K
C415CK73HB1H471KCHIP C470PF K
C290CC73GCH1H020BCHIP C2.0PFB
C291CC73GCH1H060BCHIP C6.0PFB
C292CK73HB1H471KCHIP C470PF K
C293CC73GCH1H070BCHIP C7.0PFBC
C301CK73HB1H392KCHIP C3900PF K
C302CK73HB1H271KCHIP C270PF K
C304CK73GB1A224KCHIP C0.22UF K
C306CS77AA0J4R7MCHIP TNTL 4.7UF 6.3WV
C307,308CK73HB1A104KCHIP C0.10UF K
C309CC73GCH1H820JCHIP C82PFJ
C310CK73HB1A683KCHIP C0.068UF K
C311CK73GB1A105KCHIP C1.0UF K
C312CC73GCH1H120JCHIP C12PFJ
C313CC73GCH1H121JCHIP C120PF J
C314CK73HB1A104KCHIP C0.10UF K
C315CK73GB1A105KCHIP C1.0UF K
C316CK73GB1C104KCHIP C0.10UF K
C317CK73HB1A104KCHIP C0.10UF K
C318CS77AA0J4R7MCHIP TNTL 4.7UF 6.3WV
C319CC73GCH1H271JCHIP C270PF J
C320CK73HB1C103KCHIP C0.010UF K
C321CK73GB1C473KCHIP C0.047UF K
C322CK73HB1C153KCHIP C0.015UF K
C323CC73GCH1H820JCHIP C82PFJ
C324CC73HCH1H820JCHIP C82PFJ
10
C417CK73GB1A105KCHIP C1.0UF K
C418CK73HB1E562KCHIP C5600PF K
C419CK73HB1H102KCHIP C1000PF K
C421CK73GB1A105KCHIP C1.0UF K
C424CK73HB1H471KCHIP C470PF K
C426,427CK73GB1A105KCHIP C1.0UF K
C428,429CK73HB1H102KCHIP C1000PF K
C430CK73GB1H103KCHIP C0.010UF K
C431CK73HB1C103KCHIP C0.010UF K
C432CC73HCH1H050BCHIP C5.0PFB