This TK-3202/3206 service manual contains a number
of sections which differ from the service manual (B518678-00) for the TK-3202/3206.
For items other than those in this TK-3202/3206
service manual please refer to the service manual
(B51-8678-00) for the TK-3202/3206.
CONTENTS
GENERAL ............................................................. 2
SYSTEM SET-UP ................................................. 2
This manual is intended for use by experienced technicians
familiar with similar types of commercial grade
communications equipment. It contains all required service
information for the equipment and is current as of the
publication date. Changes which may occur after publication
are covered by either Service Bulletins or Manual Revisions.
These are issued as required.
ORDERING REPLACEMENT PARTS
When ordering replacement parts or equipment information,
the full part identification number should be included. This
applies to all parts, components, kits, or chassis. If the part
number is not known, include the chassis or kit number of
which it is a part, and a sufficient description of the required
component for proper identification.
Unit
Model
& destination
TK-3202
TK-3206
TK-3202
TK-3206
TK-3202
TX-RX UnitFrequency rangeRemarks
K,M
X57-6890-20450~490MHz
M
K3
X57-6890-22400~430MHz
M3LOC : 38.4MHz
K2,
X57-6890-23470~512MHz
M2
IF1 : 38.85MHz
PERSONAL SAFETY
The following precautions are recommended for personal
safety:
●
DO NOT transmit until all RF connectors are verified secure
and any open connectors are properly terminated.
●
SHUT OFF and DO NOT operate this equipment near
electrical blasting caps or in an explosive atmosphere.
●
This equipment should be serviced by a qualified technician only.
SERVICE
This transceiver is designed for easy servicing. Refer to
the schematic diagrams, printed circuit board views, and
alignment procedures contained within.
SYSTEM SET-UP
Merchandise received
License and frequency allocated by FCC
Choose the type of transceiver
Transceiver programming
Are you using the optional antenna?
Are you using the speaker microphone?
NO
NO
Delivery
Frequency range (MHz)RF powerType
TX/RX 450~490
TX/RX 450~490
TX/RX 400~430
TX/RX 400~430
TX/RX 470~512
A personal computer (IBM PC or compatible), programming
interface (KPG-22), and programming software (KPG-87D)
are required for programming.
(The frequency, TX power HI/LOW, and signaling data are programmed
for the transceiver.)
YES
YES
KRA-23 or KRA-27
Optional antenna
KMC-17 or KMC-21
Speaker microphone
(Option)
4.0W
4.0W
4.0W
4.0W
4.0W
TK-3202 (K,M)
TK-3206 (M)
TK-3202 (K3)
TK-3206 (M3)
TK-3202 (K2,M2)
2
REALIGNMENT
TK-3202/3206
1. Modes
User mode
PC mode
Clone mode
ModeFunction
User modeFor normal use.
PC modeUsed for communication between the
Data programmingUsed to read and write frequency data
modeand other features to and from the
PC test modeUsed to check the transceiver using
Clone modeUsed to transfer programming data
Data programming
mode
PC test mode
transceiver and PC (IBM compatible).
transceiver.
the PC.
This feature is included in the FPU.
from one transceiver to another.
PC tuning mode
2. How to Enter Each Mode
ModeOperation
User modePower ON
PC modeReceived commands from PC
Clone mode
[PTT]+[Side2]+Power ON (Two seconds)
3-3. KPG-22 description
(PC programming interface cable: Option)
The KPG-22 is required to interface the TK-3202/3206 with
the computer. It has a circuit in its D-sub connector (25-pin)
case that converts the RS-232C logic level to the TTL level.
The KPG-22 connects the SP/MIC connector of the TK-3202/
3206 to the computer’s RS-232C serial port.
3-4. Programming software description
KPG-87D is the programming software for TK-3202/3206
supplied on a CD-ROM. This software runs under Windows
98, ME, Windows 2000 or XP on an IBM-PC or compatible
machine.
The data can be input to or read from TK-3202/3206 and
edited on the screen. The programmed or edited data can be
printed out. It is also possible to tune the transceiver.
IBM-PC
KPG-22
Gray+
Gray/Black–
1.5D-XV Lead wire +
1.5D-XV Shield wire –
RF Power meter
or SSG
KPG-87D
Tu ni ng cable
(E30-3216-05)
SP
}
MIC
}
3.PC Mode
3-1. Preface
The TK-3202/3206 transceivers are programmed using a
personal computer, a programming interface cable (KPG-22)
and programming software (KPG-87D).
The programming software can be used with an IBM PC
or compatible. Figure 1 shows the setup of an IBM PC for
programming.
3-2. Connection procedure
1. Connect the TK-3202/3206 to the personal computer with
the interface cable.
2. When the POWER is switched on, user mode can be
entered immediately. When the PC sends a command,
the transceiver enters PC mode.
When data is transmitting from the transceiver, the red
LED lights.
When data is received by the transceiver, the green LED
lights.
Notes:
• The data stored in the personal computer must match the
model type when it is written into the EEPROM.
• Change the TK-3202/3206 to PC mode, then attach the
interface cable.
Fig. 1
4. Clone Mode
4-1. Outline
"Clone Mode" copies the transceiver data to another
transceiver.
The dealer can copy the transceiver data to another
transceiver even without the use of a personal computer.
4-2. Example
The transceiver can copy the programming data to one or
more transceivers via RF communication.
The clone source and clone target/s must be in Clone mode.
4-3. Operation
1. To switch the clone target/s to Clone mode, press and hold
the [PTT] and [Side2] keys while turning the transceiver
power ON.
2. Wait for 2 seconds. The LED will light orange and the
transceiver will announce "Clone".
3. Select a channel table number using Side1(increment
channel table) and Side2(decrement channnel table) keys.
3
TK-3202/3206
REALIGNMENT
4. To switch the clone source to Clone mode, press and hold
the [PTT] and [Side2] keys while turning the transceiver
power ON.
5. Wait for 2 seconds. The LED will light orange and the
transceiver will announce "Clone".
6.
Select the same channel table number as the clone target/s.
7. Press [PTT] on the clone source to begin data transmission.
When the clone
light green.
When the clone source finishes sending data, a
"confirmation" tone will sound.
If data transmission fails while cloning, an "error" tone will
sound from the
8. If the cloning fails, no data will be available in the target
unit when it is returned to User mode.
9. When the cloning is successful, the target unit's "Scan"
and "Key lock" functions will return to their default values
(Scan = OFF, Key lock = OFF).
Notes:
• The dealer can clone data to two or more transceivers by
repeating the above procedures.
• If the transceivers Clone Mode is configured as "Disabled",
the transceiver cannot enter Clone mode.
• The table shown below will cover the frequency tables used
for wireless cloning.
•Clone mode cannot be entered in battery low state.
•A unit cannot be a "Source Unit" if it is unprogrammed. If
[PTT] is pressed, an "error" tone will sound.
• The language used in cloning depends on the "Model type"
setting, not the FPU setting. C, C2, C5 and C6 type
TK-3207 transceivers will use Chinese. Other types English.
• Once a unit is set to be the Source, it cannot be a target
after the data has been transmitted. This protects the data
in the Source unit.
• Electronic interface may cause a failure in data transfer
during Wireless Clone, such as when waveforms or
electromagnetics are being performed at the workbench.
• Clone mode can be used ONLY by the authorized service
personnel.
• The Clone mode setting must be configured as "Disable"
before being delivered to the end-user.
• To clone, replace the antenna from both the source
transceiver and the target transceiver with a dummy
load.
• The transmit output power is automatically set to Low
in Clone mode.
Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis.
Teile ohne Parts No. werden nicht geliefert.
TK-3202/3206 (Y50-5900-XX)
TX-RX UNIT (X57-6890-XX)
C128CK73HB1H471KCHIP C470PF K
C129CK73GB1H471KCHIP C470PF K
C130CK73HB1H471KCHIP C470PF K
C132CC73GCH1H200JCHIP C20PFJAK,AM,BM
C132CC73GCH1H270JCHIP C27PFJAK2,AM2
C132CC73GCH1H390JCHIP C39PFJBM3,AK3
C133CK73GB1H471KCHIP C470PF K
C134CK73GB1H103KCHIP C0.010UF K
C135CK73GB1C104KCHIP C0.10UF K
C136CK73GB1A105KCHIP C1.0UFK
C169CC73GCH1H100CCHIP C10PFCBM3,AK3
C190CK73GB1A105KCHIP C1.0UFK
C191CK73GB1H103KCHIP C0.010UF K
C201CK73GB1A224KCHIP C0.22UF K
C206CK73HB1H102KCHIP C1000PF K
C207CK73HB1H182KCHIP C1800PF K
C208CK73HB1H471KCHIP C470PF K
C209CS77CP0J100MCHIP-TAN10UF6.3WV
C210CK73HB1H471KCHIP C470PF K
C211CK73HB1C103KCHIP C0.010UF K
C258CK73HB1H471KCHIP C470PF K
C259CK73GB1H471KCHIP C470PF K
C262,263CK73HB1H471KCHIP C470PF K
C265CK73HB1H471KCHIP C470PF K
C266CK73GB1H471KCHIP C470PF K
AK,AK2,AM
AK,AK2,AM
AK2,AM2,BM3
C213CK73HB1A104KCHIP C0.10UF K
C214CC73HCH1H680JCHIP C68PFJ
C215CK73HB1H102KCHIP C1000PF K
C216CK73GB1C104KCHIP C0.10UF K
C217CK73HB1A104KCHIP C0.10UF K
C218CK73GB1C104KCHIP C0.10UF K
C219CC73HCH1H330JCHIP C33PFJ
C220CK73HB1H102KCHIP C1000PF K
C221CK73GB1C104KCHIP C0.10UF K
C222CK73HB1H102KCHIP C1000PF K
C224,225CK73HB1C103KCHIP C0.010UF K
C228CC73GCH1H100CCHIP C10PFC
C230CK73HB1C103KCHIP C0.010UF K
C231CK73GB1H103KCHIP C0.010UF K
C232CK73HB1C103KCHIP C0.010UF K
C233CC73GCH1H060BCHIP C6.0PFB
C234CK73HB1H102KCHIP C1000PF K
C236CC73GCH1H180JCHIP C18PFJ
C237CK73HB1H102KCHIP C1000PF K
C238CK73GB1C104KCHIP C0.10UF K
C239CK73GB1H102KCHIP C1000PF K
C240CC73GCH1H010BCHIP C1.0PFBBM3,AK3
C240CC73GCH1H3R5BCHIP C3.5PFB
C240CC73GCH1H3R5BCHIP C3.5PFBAM2,BM
C241CK73GB1H471KCHIP C470PF K
C292CK73HB1H471KCHIP C470PF K
C301CK73HB1H392KCHIP C3900PF K
C302CK73HB1H271KCHIP C270PF K
C304CK73GB1A224KCHIP C0.22UF K
C306∗ CS77CP0J4R7MCHIP-TAN4.7UF6.3WV
C307,308CK73HB1A104KCHIP C0.10UF K
C309CC73GCH1H820JCHIP C82PFJ
C310CK73HB1A683KCHIP C0.068UF K
C311CK73GB1A105KCHIP C1.0UFK
C312CC73GCH1H120JCHIP C12PFJ
C313CC73GCH1H121JCHIP C120PF J
C314CK73HB1A104KCHIP C0.10UF K
C315CK73GB1A105KCHIP C1.0UFK
C316CK73GB1C104KCHIP C0.10UF K
C317CK73HB1A104KCHIP C0.10UF K
C318∗ CS77CP0J4R7MCHIP-TAN4.7UF6.3WV
C319CC73GCH1H271JCHIP C270PF J
C320CK73HB1C103KCHIP C0.010UF K
C321CK73GB1A105KCHIP C1.0UFK
C322CK73HB1C153KCHIP C0.015UF K
C323CC73GCH1H820JCHIP C82PFJ
C324CC73HCH1H820JCHIP C82PFJ
C325CK73HB1A104KCHIP C0.10UF K
C326CK73HB1H102KCHIP C1000PF K
C327CC73HCH1H101JCHIP C100PF J
C328CK73HB1H391KCHIP C390PF K
C329,330CK73GB1A105KCHIP C1.0UFK
C331CK73HB1A104KCHIP C0.10UF K
C332CK73HB1H471KCHIP C470PF K
C333,334CK73GB1C104KCHIP C0.10UF K
C335CC73GCH1H221JCHIP C220PF J
C336CK73FB1C474KCHIP C0.47UF K
C338CC73GCH1H101JCHIP C100PF J
C339CS77AA0J100MCHIP-TAN10UF6.3WV
C340CK73GB1C104KCHIP C0.10UF K
C346CK73GB1H102KCHIP C1000PF K
C348CK73HB1H471KCHIP C470PF K
C349CK73HB1A333KCHIP C0.033UF KBM3,AK3
C351,352CK73HB1C103KCHIP C0.010UF K
C354CK73HB1A104KCHIP C0.10UF K
C370CK73HB1A104KCHIP C0.10UF K
C401CC73GCH1H471JCHIP C470PF J
C402CK73HB1H102KCHIP C1000PF K
C403CK73GB1C104KCHIP C0.10UF K
C405CC73GCH1H101JCHIP C100PF J
C406CC73HCH1H101JCHIP C100PF J
C407CK73HB1H102KCHIP C1000PF K
C408CC73HCH1H101JCHIP C100PF J
C409,410CK73GB1A105KCHIP C1.0UFK
C411CK73HB1H102KCHIP C1000PF K
C412-414CC73HCH1H101JCHIP C100PF J
C415CK73HB1H471KCHIP C470PF K
C417CK73GB1A105KCHIP C1.0UFK
C418CK73HB1E562KCHIP C5600PF K
C419CK73HB1H102KCHIP C1000PF K
C428,429CK73HB1H102KCHIP C1000PF K
C430CK73GB1H103KCHIP C0.010UF K
C431CK73HB1C103KCHIP C0.010UF K
C432CC73HCH1H050BCHIP C5.0PFB
C433,434CC73HCH1H030BCHIP C3.0PFB