Kenwood KVT-765DVD, KVT-735DVD User Manual

KVT-735DVD KVT-745DVD KVT-765DVD

MONITOR WITH DVD RECEIVER

INSTALLATION MANUAL

附DVD接收機顯示器

安裝說明書

附DVD接收機顯示器

安裝說明書

DVD수신기장착 모니터

설치설치

설치

설치설치

설명서설명서

설명서

설명서설명서

English

2 English

Before Installation

..........1

..........2

..........1

1

..........4

7

..........4

-

..........4

=

2

..........4

8

..........2

9

..........2

0

3

4

5

6

Accessories

English 3

1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery.

2. Make the proper input and output wire connections for each unit.

3. Connect the speaker wires of the wiring harness.

4. Connect the wiring harness wires in the following order: ground, battery, ignition.

5. Connect the wiring harness connector to the unit.

6. Install the unit in your car.

7. Reconnect the - battery.

8. Press the reset button.

If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

• If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die.

• If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating.

• Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.

• Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car.

• When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal.

• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.

• Mount the unit so that the mounting angle is 30° or less.

2CAUTION

2WARNING

Installation Procedure

English

Connection

4 English

B

C

B

C

( 5A )

PRK SW

A

–

+

B

C

A

Ground wire (Black) - (To car chassis)

Battery wire (Yellow)

Ignition wire (Red)

ACC

Ignition key switch

Battery

Car fuse box (Main fuse)

Connect to the vehicle's parking brake detection switch harness using the supplied relay connector.

For the sake of safety, be sure to connect the parking sensor.

2

CAUTION

Do not connect.

Monitor unit

Wiring harness (Accessory 3)

Car fuse box

Accessory 4

Accessory 2

FM/AM antenna input

Battery wire (Yellow)

Dimmer control wire (Orange/White)

To car light control switch

Ground wire (Black) - (To car chassis)

Motor antenna control wire (Blue)

Power control wire (Blue/White)

External amplifier control wire (Pink/Black)

Depending on what antenna you are using,

connect either to the control terminal of the motor

antenna, or to the power terminal for the booster

amplifier of the film-type antenna.

When using the optional power amplifier,

connect to its power control terminal.

To "EXT.AMP.CONT." terminal of the amplifier

having the external amp control function.

If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

2WARNING

English 5

MUTE

ANT. CONT

P CONT

EXT.CONT

+

ILLUMI

( 10A )

TO 5L-I/FTO NAVIGATION I/FTO TV TUNER I/FPREOUT

FM /AM

ANTENNA

AV INPUT

AV OUTPUT

TO MONITOR I/FPOWER

Disc Changer etc.

Receiver unit (front side)

Receiver unit (rear side)

Wiring harness (Accessory 1)

Mute wire (Brown)

White/Black

To front left speaker

To front right speaker

To rear left speaker

To rear right speaker

White

Gray/Black

Gray

Green/Black

Green

Purple/Black

Purple

Connect to the terminal that is grounded when either the telephone rings or during conversation.

To connect the KENWOOD navigation system, consult your navigation manual.

NOTE

Cable (included in the disc changer)

English

6 English

Connection

System Connection

AV IN

AV OUT

FM /AM

ANTENNA

AV INPUT

AV OUTPUT

POWER

TO MONITOR I/F

• Audio/Visual input

Visual input (Yellow)

Audio left input (White)

Audio right input (Red)

• Audio/Visual Output

Visual output (Yellow)

Audio left output (White)

Audio right output (Red)

• Sub-woofer (Mono) Preout

Audio left output (White)

Audio right output (Red)

• Rear Preout

Audio left output (White)

Audio right output (Red)

• Front Preout

Audio left output (White)

Audio right output (Red)

TO 5L-I/FTO NAVIGATION I/FTO TV TUNER I/FPREOUT

FRONT

REAR

WOOFER

SUB

Receiver unit (front side)

Receiver unit (rear side)

English 7

Installation

Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip).

Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place.

Accessory 5

Metal mounting strap (commercially available)

Self-tapping screw (commercially available)

Firewall or metal support

Screw (M4X8) (commercially available)

Sems bolts (M4 × 8 mm) (Accessory 7)

Tapping screw (ø4 × 16 mm) (Accessory 8)

Installation brackets (Accessory 9)

1. Attach the installation brackets 9 to the sides of the

hideaway unit using the sems bolts 7.

2. Use the tapping screw 8 to secure the hideaway unit to the

audio board.

Installation for Monitor/Player Unit

Installation for Receiver unit

English

8 English

Installation

■ Installing on Toyota, Nissan or Mitsubishi Car Using Brackets at Holes shown by "¶"

Accessory - or =

Screws (included in audio unit package)

or

Audio unit or others

Bracket

Installing in Japanese-Made Cars

English 9

When using the bracket shown above, you cannot use screws at two holes of the right and left unit sides. If so, tighten the bracket using accessories 0 as shown below.

■ Installation on Toyota Car using Brackets at Holes shown by "¶"

1. Use accessories 0 at both sides as shown.

Accessory 0

2. Mount the bracket at each side.

Accessory -

Screws (included in audio unit package)

Audio unit or others

Accessory 0

Bracket

or

3. Bend each end of accessory 0 to fix the bracket.

Use a flat-blade screwdriver or pliers, and bend each accessory tab into the hole of installation bracket to fix the bracket.

Installation

10 English

English

1. Engage the catch pins on the removal tool 6 and

remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure.

2. When the lower level is removed, remove the upper

two locations.

The frame can be removed from the top side in the same manner.

1. Refer to the section <Removing the Hard Rubber

Frame> and then remove the hard rubber frame.

2. Remove the Hex-head screw with integral washer (M4

×

6) on the back panel.

3. Insert the two removal tools 6 deeply into the slots on

each side, as shown.

4. Lower the removal tool toward the bottom, and pull out

the unit halfway while pressing towards the inside.

Be careful to avoid injury from the catch pins on the removal tool.

5. Pull the unit all the way out with your hands, being

careful not to drop it.

Accessory 6

Catch

Lock

■ Removing the Hard Rubber Frame (escutcheon)

■ Removing the Unit

Removing Monitor/Player Unit

安裝之前

附件

中文（繁體字）

1

.................. 1

2

.................. 1

3

.................. 1

4

.................. 1

5

.................. 1

6

.................. 2

7

.................. 4

8

.................. 4

9

.................. 2

0

.................. 2

-

.................. 4

=

.................. 4

中文（繁體字）

12