to the shape of the wall outlet. (Accessory
only for regions where use is necessary.)
KRF-V7771D/V8881D/VR-2080/2090
How to reset the microcomputer
The microcomputer may malfunction (impossibility of operation,
erroneous display, etc.) when the power cord is unplugged and
plugged in again while the unit is in ON mode with the
key
pressed or due to other external causes. In this case, execute the
procedure on the right to reset the microcomputer and return the
unit to the normal condition.
1 Unplug the power cord from the wall outlet.
2 While holding the
(ON/STANDBY) key depressed, plug the
power cord into the wall outlet again.
÷ Resetting the microcomputer clears the memory you entered and
returns it to the initial condition when the unit left the factory.
U.S.A. and Canada
1 With the power cord plugged in, turn the POWER key OFF.
2 Whill holding down the ON/STANDBY key, press POWER key.
Expect for U.S.A. and Canada
Please note that the following items will be deleted from
this unit’s memory if the power cord is disconnected
from the AC outlet for approximately three days.
Memory backup function
÷ The frequency setting is cleared and 87.5 MHz is selected.
÷ The preset station memory is cleared.
÷ The surround setting is cleared and reset to the initial condition.
÷ The input selection is cleared and the “Tuner” input is selected.
÷ The volume setting is cleared and the volume is set to “-66 dB”.
÷ The receiving band setting is cleared and the “FM” band is
(U.S.A., U.S.Military and Canada)
Press to switch power ON and OFF.
2POWER key
(Except for U.S.A., U.S.Military and Canada)
(China :
POWER)
Press to switch the main power ON and OFF.
3ON/STANDBY key
(Except for U.S.A., U.S.Military and Canada)
Press to switch the power mode between
STANDBY and ON.
4STANDBY indicator
Lights in STANDBY mode.
5RC sensor
Receives signals transmitted from the remote control unit.
6PHONES jack
Use for listening audio through headphones.
7SPEAKERS keys
Press each key to switch the SPEAKERS A or
SPEAKERS B ON and OFF.
Stereo indicator
MUTE indicator
TUNED indicator
Multi-mode display
While standby indicator is indicated, a small amount of power is supplied to the system to back up the memory. In this mode, the system can be
turned ON by remote control.
Display
8 Indicators
CLIP INDICATOR :
Lights when the input is clipped during
analog to digital signal conversion.
DOLBY DIGITAL :
Lights when Dolby Digital is activated.
DTS :
Lights when the DTS is activated.
9 MUTE key
Press to mute the audio temporarily.
0 RC transmitter
Sends signals to the remote control unit.
! Indicator
Lights when signal is input from or output to
the remote control unit.
@ VOLUME control knob
Rotate to adjust the volume.
# S VIDEO input jack
(Except for the VR-2080 or the KRF-V7771D
for the U.S. Military destination)
Connect the S VIDEO output jack of an AV
component.
$VIDEO input jack
Connect the composite video output (RCA)
jack of an AV component.
%AUDIO (L, R) input jacks
Connect the audio output (RCA) jacks of an AV
component.
^CD2/TAPE2 MONITOR indicator
Lights when the CD2/Tape2 (Monitor) input is
used.
&DISPLAY MODE key
Press to switch the display on the main unit.
*INPUT SELECTOR key
Press to switch the input as shown below.
TUNER
CD1
MD/Tape1
VIDEO1
VIDEO2
VIDEO3
VIDEO4
AV AUX
PHONO
KRF-V7771D/V8881D/VR-2080/2090
CONTROLS
3
ON/STANDBY
MUTE
VOLUME
ENTER
Setup Surround
SP Level
Surr.SP Type
SP Distance
SP Selection
Tuner
CD1
Video2
Video3 Video4
Video1
TV1
Phono
TV2
CD2
MD/
Tape1
CD2/
Tape2
Input
Digital
Input
Analog
AV AUX
Macro
Remote
Mode
Main
Menu
CONFIRM
23
¶
•
ª
£
⁄
)
¡
(º¢
1
6547890!@#$
%^
& *∞§
™
RC : Infrared system
Perform “Model Type Setup”
of the RC before using it.
The following menu display appears after the batteries are
loaded for the first time.
Controls and indicators
The Remote Control unit provided with the Receiver can also control KENWOOD MD recorder, cassette decks, CD player, DVD
player and LD player which are connected to it through system control cords. For details of the controllable functions, refer to
the instruction manuals of these components.
The displayed icons are variable depending of the “Model Type Setup” for
matching specifications with the Reciever which uses the RC unit and “Setup” for
matching specifications with connected source component.
1Segment screen
The fixed icons are displayed in
this area.
2TV1 icon
Select to display the TV1 control
screen.
3Main Menu icon
Select to display the Main Menu
screen.
4TV2 icon
Select to display the TV2 control
screen.
5Phono icon
Select to select the PHONO input.
6Video1 icon
Select to control Video1.
7CD1 icon
Select to control CD1.
8Video2 icon
Select to control Video2.
9CD2 icon
Select to control CD2.
(Room B only)
0Video3 icon
Select to control Video3.
! Tuner icon
Select to control Tuner.
@ Video4icon
Select to control Video4.
# MD/Tape1 icon
Select to control MD or Tape1.
$ CD2/Tape2 icon
Select to monitor the CD2/Tape2
input. (Room A only)
% AV AUX icon
Select to select the AV AUX input.
^ Input Digital icon
Select to play a digital input or to
switch between Auto and Manual.
& Macro icon
Select to control Macro.
* Input Analog icon
Select to play an analog input.
( Remote Mode icon
Select to switch the remote control operation mode without
changing the selected input.
Segment screen
Operation keysMenu screen
)Menu screen
Control key icons and control levels are displayed in
this area.
¡Status display
The example in the illustration shows the “SetupSurround” status.
™SP Selection icon
Select to set up the speakers.
£Return icon
Select to return to the previous menu screen.
¢Status display
Shows the communication
status.
∞Joy stick key
This key is used to select an
icon. This key can be controlled
in 4 directions.
§ENTER key
Press to enter the selection of
an icon.
¶VOLUME (up) control key
Press to increase the volume.
•VOLUME (down) control
key
Press to decrease the volume.
ªCONFIRM key
Press to select the currently
displayed items.
ºMUTE key
Press to mute the audio
temporarily.
⁄ (ON/STANDBY) key
Press to turn this unit and the
components connected to it
through system cords between
ON and STANDBY modes.
KRF-V7771D/V8881D/VR-2080/2090
CONTROLS
Note
Note
Model
Type Setu
Model 1
Model 2
Model 3
p
4
6
6
3
4
4
9
9
3
3
2
11
12
1
4
3
5
x2
9
x5
8
x2
3
x2
7
13
13
13
14
14
15
10
1
2
2
2
1
x3
2
x3
2
2
x2
x5
2
x2
2
3
3
3
3
1
3
x29
DISASSEMBLY FOR REPAIR
Fig. 1
[Check the vertical PCB]
1. (Exist bottom plate) Remove the hook of rear
panel(1).
2. Remove the 29(Exist bottom plate: 34)
screws(2), then remove the rear panel.
3. Connect the GND of the phono terminal, the
GND of antenna shield board,the GND of
coax., the GND of system control shield
board, the GND of SP terminal shield board
and the chassis with 5 wires connected alligator chips(3).
KRF-V7771D/V8881D/VR-2080/2090
[Remove the bottom plate.]
Make use of the changing final transistor etc.
1. Remove the 19 screws (1, 2) and PCB support, then
remove the bottom plate.
Fig. 2
[Remove the escutcheon (operation
panel)]
1. Remove the knob(1), the nut (2), the 11
Fig. 3
screws(3, 4, 5) and 2 hooks (6 ), then
remove the front panel ass'y.
2. Remove the lead wire(7), the 2 screws(8 :
except K,P type) and 7 screws(9) then
remove the PCB.
3. Remove the under front glass(0, -), then
remove the front panel(=) from the sub
panel.
4. Remove the 2 under escutcheon sides(~) by
· screw driver and the 2 hooks(!) then
remove the escutcheon(@).
VIDEO SEL.
DIGITAL INPUT SEL.
WIDE V-MUTE
VIDEO SYNC
TONE CONT.
PROTECTION
455kHz FILTER
VR-2090 (K,P)
(X11) J13 (1/2)
IR RECEIVER IN
REPEATER OUT
(X11) J14
VR-2090 (K,P)
IC86
(X08)
6
FANFAN DRIVER
(X07) Q211-215
PARALEL
SIRIAL/
OUT LED
(X11) D21-24
IR LED REMOTE OUT
(X11) J13 (2/2)(X08) Q64-66
(X08) IC67
REMOTE
u-COM
SENSOR
TV or LIGHT
RELAY CONTROL
(X11) J12
RDS
(X08) IC68
(X08) IC69
MAIN u-COM
DATA-OUT
SUB u-COM
REMOTE SENSOR
(X25) A1
KEY MATRIX
FL
(X25) ED1
FL DRIVER
(X25) IC61
LED
PEAK LEVEL
LED
1.0/1K
PRE OUT
PRE OUT
SPEAKERS
FRONT A
L,R
PHONES
C
SL,SR
FRONT B
ROOM B SP
C
SL,SR
SW
SECOUND ROOM PRE OUT
B-MUTE
SW-MUTE
S-MUTE
A-MUTE
RELAY B
RELAY CS
RELAY A
RELAY S
BUFFER
IC31(2/2)
BUFFER
IC30
IC31(1/2)
BUFFER
K2
29dB POWER
(X25)(X07)
29dB POWER
(X25)(X07)
AMPLIFIER
29dB POWER
(X25)(X07)
K1
K1
K4
K3
MUTE
Q1-4
MUTE
Q36
MUTE
Q33,34
Q35
MUTE
SW-MUTE
B-MUTE
A-MUTE
-20dB ATT
MUTE
Q5,6
MUTE
MUTE
MUTE
MUTE
Q3,4
Q11
Q7,8
Q12
BUFFERAMP
IC22
IC26
IC24
(2/2)
IC26
(1/2)
ATT
-20dB
ATT
-20dB
ATT
-20dB
ATT
Q1,2
Q5,6
-20dB
Q9
Q10
IC28
IC53
(2/2)
IC52
IC53
(1/2)
IC51
ROOM B
IC27
IC25(2/2)
IC23
IC25(1/2)
IC21
VOLUME
VOLUME
VOLUME
VOLUME
VOLUME
L7,R7
L8,R8
L4,R4
IC44
IC43
TONE
L6,R6
L1,R1
L3,R3
L2,R2
(X11)
LOW BOOST
IC47,48
CONFIG-2
IC49
INV
VIDEO
SECOND(B)
ROOM
D82
GND
+30V
63-65,73
IC57,61,
AVR
AVR
IC82
AVR
IC83
D86
D311
EXCEPT K.P
EXCEPT K.P
(X07) T1
K5
D312
AC OUTLET
DRIVER
RELAY
Q301
K6
STROKE SW
FIL
FIL
-35V
AVR
Q311
D88
AVR
IC84
GND
+5.0V
To VIDEO 5
To VIDEO 5
AVR
Q85
AVR
Q86
AVR
Q83
AVR
Q84
D81
+17V
GND
-17V
DRIVER
RELAY
Q154
D252
D251
PRE DRIVE
GND
PRE DRIVE
GND
FINAL TR.
FINAL TR.
D301-304
GND
+5.6V
(X07) IC31
AVR
Q13
VIDEO 2
Q14
VIDEO 1
Q12
Q30
Q16
Q31
Q15
MONITOR OUT
1Vp-p/75
(S1-VIDEO)
PLAY
REC
AV AUX
(FRONT)
VIDEO 4
VIDEO 3
VIDEO 2
VIDEO 1
(VISUAL)
1Vp-p/75
(OSD)
(SECOND ROOM)IC52(1/2)
Q17
MONITOR OUT B
Q55
MONITOR OUT
IC52(2/2)
IC13
TC74HC4051AP
IC51
SN761200N
Q51
Q52
VIDEO
REC
COMP
PLAY
VIDEO
COMP
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
(FRONT)
AV AUX
VIDEO 1
VIDEO 2
IC11,12
SN761200Nx2
Q11
Ω
Ω
Ω
Ω
Ω
Ω
BLOCK DIAGRAM
7
8
KRF-V7771D/V8881D/VR-2080/2090
(0 : Pull down, 1 : Pull up)
TYPEBAND
Reception
frequency
Channel
IF
PLL standard
Diode sw
space
frequency
DSW3DSW2DSW1DSW0
K1
FM87.5MHz~108.0MHz100kHz+10.7MHz25kHz
0000
1700
AM530kHz~1700kHz10kHz+450kHz10kHz
K2
FM87.5MHz~108.0MHz100kHz+10.7MHz25kHz
0001
1610
AM530kHz~1610kHz10kHz+450kHz10kHz
K4
FM87.5MHz~108.0MHz100kHz+10.7MHz25kHz
1010
1700 RBDS
AM530kHz~1700kHz10kHz+450kHz10kHz
E1
FM87.5MHz~108.0MHz50kHz+10.7MHz25kHz
0011
AM531kHz~1602kHz9kHz+450kHz9kHz
E3
FM87.5MHz~108.0MHz50kHz+10.7MHz25kHz
RDS
AM531kHz~1602kHz9kHz+450kHz9kHz
0101
FM L65.0MHz~74.0MHz10kHz+10.7MHz5kHz
Q1
FM H 87.5MHz~108.0MHz50kHz+10.7MHz5kHz
1011
RDS
AM531kHz~1602kHz9kHz+450kHz9kHz
M
K2/E1 is switched with only the setting of DSW1 (X11 : S601).
00X1
(DSW1 = 0 : K2 type, 1 : E1 type)
77767574
CIRCUIT DESCRIPTION
1. The back up item and initialization
condition
1-1 Back up
• POWER ON/OFF: OFF
• VOLUME LEVEL: -66dB
• AUDIO INPUT • SELECTOR : TUNER
• VIDEO INPUT • SELECTOR : VIDEO1
• SPEAKER A: ON
• SPEAKER B: OFF
• CD2/TAPE2 MONITOR: TAPE2 OFF
• TONE: OFF
• LOUDNESS: OFF
• DISPLAY MODE: DEVICE+DGTL/ANLG
• RDS DISPLAY MODE: FREQUENCY
• DIMMER: DIMMER 1 (LIGHTEST)
• SURROUND MODE: STEREO
• DSP MODE: ARENA
• ROOM SIZE: Med
• WALL TYPE: Med
• EFFECT LEVEL: 3
• MIDNIGHT MODE: OFF
• DISTANCE: FL/FR : 10ft
: C : 10ft
: RS/LS : 5ft
: SW : 10ft
• FRONT SP.: LARGE
• CENTER SP.: NORMAL
• SURROUND SP.: NORMAL/WIRED
• SUB WOOFER: ON
• SW Re-Mix: OFF
• INPUT LEVEL: 0dB
• CH. LEVEL: 0dB
• TONE BASS: 0dB
• TONE TREBLE: 0dB
• TUNING MODE: AUTO
• PRESET MEMORY: TEST MEMORY FREQUENCY (Same value with KR-V999D/1090VR)
• LAST BAND: FM
• FM LAST FREQUENCY: 87.5MHz
• AM LAST FREQUENCY: 531kHz (CH. SP 9kHz)
: 530kHz (CH. SP 10kHz)
• LAST P. ch: [- -ch]
• PTY SELECT MODE: OFF
• PTY SEARCH MODE: OFF
• TP SEARCH MODE: OFF
• RDS DISPLAY MODE: FREQUENCY MODE
1-2 The initial setting
While pressing POWER key, plug the AC power cord
into an AC outlet (K,P type) or turn on the AC POWER
switch.
2. Condition by the destination or model
3. TEST MODE
[setting method]
While pressing INPUT SELECTOR key, plug the AC
power cord into an AC outlet (K, P type) or turn on the
AC POWER switch. When a set is set up in test mode
condition a set becomes the following condition.
Automatic POWER ON. All indicator tube (FL) and
9
CLIP INDICATOR LED are lighted. The other LED are
flashed.
A backup at the thing except ON/OFF of POWER is
initialized.
4. Main microprocessor uPD78078GF-080 (X08 : IC69)
4-1 Microprocessor periphery block diagram
10
KRF-V7771D/V8881D/VR-2080/2090
CIRCUIT DESCRIPTION
4-2 Pin description
Pin No.Pin NameI/OConnectDescription
1VOL_STBOPDVOLUME IC CE (TC9412AP/TC9413AP)
2VOL_CLKOPDVOLUME IC CLOCK (TC9412AP/TC9413AP)
TONE IC CLOCK (TC9184AP)
3VOL_DATAOPDVOLUME IC DATA (TC9412AP/TC9413AP)
TONE IC DATA (TC9184AP)
4SEL_STB1OPDANALOG SW. STROBE (NJU731x)
5SEL_STB2OPDANALOG SW. STROBE (NJU7311-NJU7313)
6VIDEO_STBOPDVIDEO IC STROBE (NJU3713)
7SEL_CLKOPDANALOG SW. CLOCK (NJU7311-NJU7313)
VIDEO IC CLOCK (NJU3713D)
8SEL_DATAOPDANALOG SW. DATA (NJU7311-NJU7313)
22CEI–BACK UP CE
23AVdd–VDD+5V
24AVrefoIVDDA/D POWER SUPPLY
25RDS_SLEVELIPDRDS SLEVEL (SAA6579)
26T_MUTEOPDTUNER MUTE
27PLL_CLKOPDPLL IC CLOCK (LC73131)
28PLL_DATAOPDPLL IC DATA (LC72131)
29PLL_CEOPDPLL IC CE (LC72131)
30SDIPUSD INPUT
31STEREOIPUSTEREO INPUT
32PLL_DOIPDPLL IC LC72131 DO (LC72131)
33AVss–VSSGND
34SUB_RESETOPDSUB uCOM RESET (uPD78058GC-A74)
35V_PDETIPUPERFECT MACRO VIDEO POWER DETECT
36AVref1IVDD+5V
37UART_RXDIPDMEGA CHANGER CD DATA RECEIVE
POWER LINE REMOCON CODE RECEIVE
38UART_TXDOPDMEGA CHANGER CD DATA TRANSMIT
POWER LINE REMOCON CODE TRANSMIT
39VSEL_TROPDPERFECT MACRO VIDEO SELECTOR POWER SUPPLY SW. Tr
40Vss–GNDGND
41SDTIPDuCOM-uCOM COMMUNICATION SLAVE DATA
(uPD78058GC-A74)
42MDTOPDuCOM-uCOM COMMUNICATION MASTER DATA
(uPD78058GC-A74)
43MCKOPDuCOM-uCOM COMMUNICATION MASTER CLOCK
(uPD78058GC-A74)
44MREQOPDuCOM-uCOM COMMUNICATION MASTER REQUEST
(uPD78058GC-A74)
11
KRF-V7771D/V8881D/VR-2080/2090
CIRCUIT DESCRIPTION
Pin No.Pin NameI/OConnectDescription
45SREQIPDuCOM-uCOM COMMUNICATION SLAVE REQUEST
(uPD78058GC-A74)
46FL_DOUTIPDFL DRIVER DATA IN
47FL_DINOPDFL DRIVER DATA OUT
48FL_CLKOPDFL DRIVER CLOCK
49FL_STBOPDFL DRIVER STROBE
50VSEL_CTLAOPDPERFECT MACRO VIDEO SELECTOR CONTROL A
51VSEL_CTLBOPDPERFECT MACRO VIDEO SELECTOR CONTROL B
52FAN_1IPDFAN DETECT 1
53FAN_2IPDFAN DETECT 2
54FAN_3IPDFAN DETECT 3
55SDATAI/O–SERIAL DATA
56SBUSYI/O–SERIAL BUSY
57RELAY_AOPDSPEAKER A RELAY
58RELAY_BOPDSPEAKER B RELAY
59RELAY_CSOPDCENTER/SURROUND SPEAKER RELAY
60RELAY_TROPDTRANS RELAY
61RELAY_POWEROPDPOWER RELAY
62EXT_OUTOPDEXTERNAL OUT
63NCOPDNO USED
64DRV_RSTOPDFL DRIVER RESET
65TV_PDETIPDPERFECT MACRO TV POWER DETECT
66999_888I–TYPE SELECTH : VR-2090L : VR-2080
678_16I–SERIAL SELECTL : SERIAL 16bitH : SERIAL 8bit
68, 69ENC_VOL2, 1IPDVOLUME ENCODER IN
70PROTECTION1IPDPROTECT DETECT
71Vss–GNDGND
72PROTECTION2IPDPROTECT DETECT
73NCIPDNO USED
74~76TSW_0~2I–TUNER SIMUKE SWITCH 0~2
77TSW_3 (CH. SP)IPDTUNER SIMUKE SWITCH 3 (CHANNEL SPACE)
78NCI–NO USED
79RELAY_MULTIOPDSP B SIGNAL OUTPUTROOM A : LROOM B : H
80, 81DIN_1, 2OPDDIGITAL REC SELECT (TC74HC153AF)
82DIN_STBOPDDIGITAL REC SELECT STROBE (TC74HC153AF)
83SMK_REQOPDREMOCON DATA TRANSMIT IC REQ
84SMK_ENBIPDREMOCON DATA TRANSMIT IC ENB
85SMK_RWRIPDREMOCON DATA TRANSMIT IC RWR
86~93SMK_D0~D7OPDREMOCON DATA TRANSMIT IC D0~D7
94MUTE_AOPUROOM A MUTE
95MUTE_BOPUROOM B MUTE
96SW_MUTEOPUSWch MUTE
97-20dB_ATTOPU-20dB ATTENUATER
98VIDEO_MUTEOPDVIDEO MUTE
99SCH_MUTEOPDSch MUTE
3SCL/CCLKSerial communication CLOCK
4SDA/CDOUTSerial data line CS4226 î SUB uCOM
5ADI/CD INSerial data line SUB uCOM î CS4226
6ACO/CSCS4226 CHIP SELECT
7SPI/I2CSerial control format setting
8PDNPowerdown Pin
9AIN3R/AUDIOaudio/non-audio detect
10AIN3L/AUTODATAInput C bit, V bit H : Signal of AC-3, MPEG, DTS
11AIN2L/FREQ0Channel Status Freq. Bit
12AIN2R/FREQ1Channel Status Freq. Bit
30OVL/ERRInput Analog : ADC clipping indicator
Input Digital : D/PDIF error indicator
-= FREQ0/FREQ1
32kHz44.1kHz48kHzReserved
FREQ1HLLH
FREQ0HLHL
0 AC3
AC-3/MPEG Data Stream InputExistNone
AC3, MPEG, DTS10
∞ CLIP INDICATOR (X25 : D66) CONTROL
IC62 (CODEC)IC66 (Sub u-COM)
INPUT SOURCE∞ CS_OVL_ERR™ PEAK_LEVEL OUTPUT
DIGITALdon't careL
ANALOGLL
HH
H : LED LIGHTING
16
KRF-V7771D/V8881D/VR-2080/2090
SYSTEM
CONTROL
FRONT SPEAKERS
(6-16 Ω)
CENTER
SPEAKER
(6-16 Ω)
SURROUND SPEAKERS
DIGITAL IN
CD1
COAXIAL
VIDEO 4
COAXIAL
VIDEO 3
OPTICAL
VIDEO 2
OPTICAL
SL 16 XS 8
(
SL 16
)
(
XS 8
)
(
6-16 Ω
)
OPTICAL
DIGITAL OUT
SWITCHED
L
R
A
L
R
L
C
R
B
SL 16
TEXT
IR
RECEIVER
IN
RELAY
CONTROL
IR
OUT
LCD
REMOTE
IR REPEATER OUT
TV
ON/OFF
SENSOR
L
R
R
R
L
R
ANTENNA
AM
-FM 75Ω
GND
CD1
PHONO
MD/
TAPE 1
REC
OUT
PLAY
IN
REC
OUT
PLAY
IN
PLAY
IN
PLAY
IN
CD2 /
TAPE 2
MONITOR
MONITOR
OUT
SURROUND
CENTER
SUB
WOOFER
L
L
R
VIDEO
S VIDEO
VIDEO
SECOND ROOM PRE OUT
PRE OUT
AUDIO
VIDEO 3
VIDEO 4
PLAY
IN
VIDEO 2
VIDEO 1
L
R
AUDIO
PLAY
IN
REC
OUT
+
-
AUDIO
(A)
(B)
(C)
FM SG
FM SG
AG
MPXAG
AC voltmeter
Dummy antenna
Oscilloscope
Distortion meter
No.
ITEM
INPUT
SETTINGS
OUTPUT
SETTINGS
RECEIVER
SETTINGS
ALIGNMENT
POINTS
ALIGN FOR
FIG.
1DISCRIMINATOR
(A)
98.0MHz 1kHz,
±75kHz dev.
70dBf (ANT. input)
Connect a
DC voltmeter
between CN12 1
and CN12 2 (X11)
MONO
98.0MHz
L604
(X11)
0V(a)
2
DISTORTION
(MONO)
(A)
98.0MHz 1kHz,
±75kHz dev. MONO
70dBf (ANT. input)
(B)
MONO
98.0MHz
L605
(X11)
Minimum
distortion
(a)
3
DISTORTION
(STEREO)
(C)
98.0MHz 1kHz,
±67.5kHz dev.
Selector : L or R Pilot
: ±7.5kHz dev.
70dBf (ANT. input)
(B)
AUTO
98.0MHz
IFT(RF
FRONTEND
: A1)
Minimum
distortion
(L or R)
(a)
4TUNING LEVEL
(A)
98.0MHz MONO
1kHz, ±75kHz dev.
15dBf (ANT. input)
(B)
MONO
98.0MHz
VR601
(X11)
Adjust VR601
and stop at the
point where ED1
(TUNED) goes
on.
(a)
1
DISTORTION
(STEREO)
(C)
98.0MHz 1kHz,
±67.5kHz dev.
Selector : L or R,Pilot
: ±7.5kHz dev.
70dBf (ANT. input)
(B)
AUTO
98.0MHz
IFT
(TUNER UNIT
: A601)
Minimum
distortion
(L or R)
(a)
2TUNING LEVEL
(A)
98.0MHz MONO
1kHz, ±75kHz dev.
15dBf (ANT. input)
(B)
MONO
98.0MHz
VR601
(TUNER UNIT)
Adjust VR601
and stop at the
point where
ED1 (TUNED)
goes on.
(a)
FM SECTION : Except M type SELECTOR : FM *Adjust NO.1 and NO.2 repeat.
FM SECTION :M type only SELECTOR : FM
ADJUSTMENT
SYSTEM CONNECTIONS
17
KRF-V7771D/V8881D/VR-2080/2090
No.ITEM
INPUT
SETTINGS
OUTPUT
SETTINGS
RECEIVER
SETTINGS
ALIGNMENT
POINTS
ALIGN FORFIG.
AUDIO SECTION SPEAKER : A PREOUT : OFF PROLOGIC : ON
<1>IDLE CURRENT—
Connect a DC
voltmeter across
CN1 (each port)
1, 2 pin : L
5, 6 pin : R
3, 4 pin : SL
7, 8 pin : SR
9, 10 pin : C