Kenwood KDC-X494, KDC-MP445U User Manual

CD-RECEIVER

KDC-X494 KDC-MP445U KMR-440U

INSTRUCTION MANUAL

The latest version of the Instruction Manual can be downloaded from www.kenwood.com/cs/ce/. Before reading this manual, please access this site to check whether your manual is the latest one.

Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model KDC-X494/ KDC-MP445U/ KMR-440U Serial number

US R esid en ce On ly

Regi ster Online

Before use 3

Basic Operations 4

General opreration 6

Removing the Faceplate Muting the audio upon reception of phone call

Audio Adjustments 7

Audio Control Audio Preset Memory Audio Preset Recall

Music disc/Audio file Operation 9

Music Search Music Search for iPod Alphabet Search Skip Search Direct Search Related Search My Playlist for iPod Direct Music Search Basic Operation of Disc Changer (Optional) Direct Search in Disc Changer (Optional)

Tuner Operation 14

Station Preset Memory Preset Tuning Direct Access Tuning

Favorite Control 15

Favorite Preset Memory Favorite Preset Recall Deleting Favorite Preset Memory

Function setting 16

Display Settings 22

Selecting Display Type Selecting Text Display

HD Radio™ tuner control 24

Tuning Station Preset Memory Preset Tuning iTunes Tagging Direct Access Tuning

Satellite Radio tuner (Optional Accessory) control 26

Basic Operation Category and Channel Search Channel Preset Memory Preset Tuning Channel Scan Direct Access Tuning

Operation of hands-free phoning 28

Before Use Receiving a call Calling a number in the Phone Book Dialing a number Calling a number in the call log Speed dialing (Preset dial) Registering to the Preset Dial Number List During a call Call waiting Clearing the Disconnection Message Making a voice dialing call Displays of phone number type (category)

Bluetooth Audio Operation 31

Before Use Basic Operation

Bluetooth Setup 32

Registering Bluetooth device Registering Special Bluetooth device Registering PIN Code Downloading the Phone Book Selecting the Bluetooth device You Wish to

Connect Deleting a Registered Bluetooth device Displaying the Firmware Version Adding a voice dialing command Setting a Voice Command for Category

SMS (Short Message Service) 37

Displaying the SMS Downloading the SMS

Basic Operations of remote control 38

Appendix 39

Troubleshooting Guide 41

Specifications 43

KDC-X494/ KDC-MP445U/ KMR-440U

Before use

2WARNING To prevent injury or fire, take the following

precautions:

• To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit.

Before using this unit for the first time

This unit is initially set on the Demonstration mode. When using this unit for the first time, cancel the Demonstration mode. Refer to <Exit Demonstration

Mode> (page 4).

How to reset your unit

• If the unit fails to operate properly, press the Reset button. The unit returns to factory settings when the Reset button is pressed.

Reset button

Cleaning the Unit

If the faceplate of this unit is stained, wipe it with a clean soft dry such as a silicon cloth. If the faceplate is stained badly, wipe the stain off with a cloth moistened with a neutral cleaner, then wipe it again with a clean soft dry cloth. Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erase characters.

Unit and Faceplate Terminals

• To prevent deterioration, do not touch the terminals of the unit and faceplate with your fingers.

• If the terminals on the unit or faceplate get dirty, wipe them with a clean soft dry cloth.

Notes

• If you experience problems during installation, consult your Kenwood dealer.

• When you purchase optional accessories, check with your Kenwood dealer to make sure that they work with your model and in your area.

• Characters that conform to ISO 8859-1 can be displayed.

• The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations on the display may be inapplicable.

Handling CDs

• Do not touch the recording surface of the CD.

• Do not stick tape etc. on the CD, or use a CD with tape stuck on it.

• Do not use disc type accessories.

• Clean from the center of the disc and move outward.

• When removing CDs from this unit, pull them out horizontally.

• If the CD center hole or outside rim has burrs, use the CD only after removing the burrs with a ballpoint pen etc.

CDs that cannot be used

• CDs that are not round cannot be used.

• CDs with coloring on the recording surface or CDs that are dirty cannot be used.

• This unit can only play the CDs with This unit may not correctly play discs which do not have the mark.

• You cannot play a CD-R or CD-RW that has not been finalized. (For the finalization process refer to your CD-R/CD-RW writing software, and your CD-R/ CD-RW recorder instruction manual.)

• 3 inch CD cannot be used. Attempt to insert using an adapter can cause malfunction.

Lens Fogging

When you turn on the car heater in cold weather, dew or condensation may form on the lens in the CD player of the unit. Called lens fogging, this condensation on the lens may not allow CDs to play. In such a situation, remove the disc and wait for the condensation to evaporate. If the unit still does not operate normally after a while, consult your Kenwood dealer.

English

Basic Operations

[ ]

[SRC]

[FNC]

Release

Control

[ENTER] [FAVORITE] [S.MODE] [AUDIO]

Disc slot

Knob

Before Using

Exit Demonstration Mode

Turn off the demonstration mode when you use it for the first time after installation.

1 Press the [ENTER] button to quit the

demonstration mode when the messages “To Cancel DEMO Press the ENTER Key” are displayed (approx. 15 seconds).

2 Turn the Control knob to select “YES”, and then

press the [ENTER] button. The demonstration mode can also be canceled in the Function setting mode. Refer to 36 Demo

Mode of <Function setting> (page 16).

Adjusting the Clock & Date

1 Press the [FNC] button to enter the Function

setting mode.

2 The item can be selected and determined as

follows. ”Settings” ➜ “Clock & Date” ➜ “Clock Adjust” To select the item, turn the Control knob. To determine the item, press the [ENTER] button.

3 Turn the Control knob to adjust the hour, and

then press the [ENTER] button.

4 Turn the Control knob to adjust the minute, and

then press the [ENTER] button.

5 Turn the Control knob to select “Date Adjust”, and

then press the [ENTER] button.

6 Turn the Control knob to adjust the year, and

then press the [ENTER] button.

7 Turn the Control knob to adjust the month, and

then press the [ENTER] button.

8 Turn the Control knob to adjust the day, and then

press the [ENTER] button.

KDC-X494/ KDC-MP445U/ KMR-440U

[0]

USB Terminal

Auxiliary input

9 Turn the Control knob to select “Date Mode”, and

then press the [ENTER] button.

10 Turn the Control knob to select Date format, and

then press the [ENTER] button.

11 Press the [ ] button for at least 1 second to

exit the Function setting mode.

Common Operation

Power and source selection

Turns the power ON by pressing the [SRC] button. When the power is ON, select a source. Press the [SRC] button and then turn the Control knob. To determine the selected source, press the [ENTER] button. Tuner (“TUNER” or “HD RADIO”) ➜ USB (“USB”) or iPod (“iPod”) ➜ CD (“CD”) ➜ Auxiliary Input (“AUX”) ➜ Standby (“STANDBY”) ➜ Tuner (“TUNER”) Press the [SRC] button for at least 1 second to turn the power OFF.

⁄

• You can select the source selection mode to switch

between sources each time you press the [SRC] button. Set

28 Source Select Mode of <Function setting> (page 16) to “2”.

• The source “iPod” and “CD” can be selected when each

source is ready to play.

• When an optional accessory is connected, the source name

for each device appears.

• The power will be turned off automatically after about 20

minutes have lapsed in standby mode. (KMR-440U only)

Volume

Turn the Control knob to adjust the sound volume.

Display scroll

Keep the [S.MODE] button pressed down to scroll through the CD or audio file text display.

Auxiliary input

Portable audio device can be connected with the stereo mini-plug (3.5 mm ø).

Playing Music (CD/USB/iPod)

Playing Disc

Insert the disc in the Disc slot. When inserted, the source is switched automatically and a song starts playing.

Playing USB device

Connect a USB device or iPod to the USB terminal. When connected, the source is switched automatically and a song starts playing.

Selecting an Audio file folder

Push the Control knob towards up or down to select a folder.

Selecting a Song

Push the Control knob towards right or left to select a song (track or file).

Fast Forwards or Fast Backwards the music

Push and hold the Control knob towards right or left to fast-forward or fast-backward the audio file containing songs (tracks or files).

Pause and play

Press the [ ] button to pause or resume playing a song (track or file).

Removing Disc and USB device

Press the [0] button to eject a disc. Keeping the button pressed for at least 2 seconds enters the USB Remove mode (“USB REMOVE” is displayed) and the USB device can be removed safely.

⁄

• CA-U1EX (optional accessory) is recommended to connect

a USB device.

CA-U1EX

• KCA-iP101 (optional accessory) is recommended to connect

an iPod.

• For the playable audio files, devices, iPod, see <Appendix>

(page 39).

Listening to Radio

Selecting a Tuner source

1 Press the [SRC] button. 2 Turn the Control knob to select “TUNER”, and

then press the [ENTER] button.

Selecting the Band

Push the Control knob towards up to change the band in the order of FM1 ➜ FM2 ➜ FM3. Push the Control knob towards down to change the band to AM.

Selecting a Station

Push the Control knob leftward and rightward to select the station you want to listen to.

⁄

• Details of the station selecting in operation are set in the 22

Seek Mode of <Function setting> (page 16).

English

General opreration

Removing the Faceplate

The faceplate of the unit can be detached and taken with you, helping to deter theft.

Detaching the Faceplate

Press the Release button.

Reattaching the Faceplate

Refer to the following diagram when reattaching the faceplate.

• Remove the faceplate at once after pressing the Release

button; otherwise it can fall down due to vibration.

• The faceplate is a precision piece of equipment and can be

damaged by shocks or jolts.

• Keep the faceplate in its faceplate case while detached.

• Do not place the faceplate (and the faceplate case) in areas

exposed to direct sunlight, excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.

Muting the audio upon reception of phone call

The audio system automatically mutes when a call comes in.

When a call comes in

“CALL” is displayed. The audio system pauses.

Listening to the audio during a call

Press the [SRC] button.

The “CALL” display disappears and the audio system comes back ON.

When the call ends

Hang up the phone.

The “CALL” display disappears and the audio system comes back ON.

⁄

• To use the TEL Mute feature, you need to hook up the MUTE

wire to your telephone using a commercial telephone accessory. Refer to <Connecting Wires to Terminals> (Quick Start Guide).

KDC-X494/ KDC-MP445U/ KMR-440U

Audio Adjustments

Audio Control

You can adjust following Audio Control items;

Display Audio item Range

“SubWoofer” Subwoofer output OFF/ON “Bass Boost” Bass Boost Level1/Level2/OFF “System Q” Preset Equalizer

curve

“Bass Adjust”

“Bass Center FRQ” Bass Center

Frequency*

“Bass Level” Bass level –8 — +8 (dB) “Bass Q Factor” Bass Q Factor* 1.00/1.25/1.50/2.00 “Bass EXT” Bass Extend* OFF/ON

“Middle Adjust”

“Middle Center FRQ”

Middle Center Frequency*

“Middle Level” Middle level –8 — +8 (dB) “Middle Q Factor” Middle Q Factor* 1.00/2.00

“Treble Adjust”

“Treble Center FRQ” Treble Center

Frequency*

“Treble Level” Treble level –8 — +8 (dB) “Balance” Balance Left 15 — Right 15 “Fader” Fader Rear 15 — Front 15 “2Zone Rear Volume” Rear volume during

Dual zone

“SubWoofer Level” Subwoofer level –15 — +15 (dB)

“Detailed Settings”

“HPF Front” Front High Pass

Filter

“HPF Rear” Rear High Pass Filter Through/40*/60*/80/

“LPF SubWoofer” Low Pass Filter 50*/60/80/100*/120/

“Subwoofer Phase” Subwoofer Phase Reverse (180°)/

“2Zone” Dual Zone System ON/OFF

“2Zone F/R Select” Dual Zone output

channel “Supreme” Supreme setting ON/OFF “Audio Preset” Audio Preset

“Volume Offset

†

memoy

Volume offset –8 — ±0 (dB) ADJ”

*Function of KDC-X494.

†

Refer to <Audio Preset Memory> (page 8), <Audio Preset

Recall> (page 8)

“Rock”/ “Pops”/ “Easy”/ “Top40”/ “Jazz”/ ”Game”/ “Natural”/ “User”

40/50/60/70/80/100/ 120/150 (Hz)

0.5/1.0/1.5/2.0 (kHz)

10.0/12.5/15.0/17.5 kHz

0 — 35

Through/40*/60*/80/ 100/120/150/180/220* (Hz)

100/120/150/180/220* (Hz)

Through (Hz)

Normal (0°)

Rear/Front

Recall/Memory

(AUX: -8 — +8)

⁄

• ‡“User”: The customized Bass, Middle, and Treble levels are

effective.

• You can set Bass, Middle, and Treble for each source.

About Supreme Technology to extrapolate and supplement with proprietary algorithm, the high-frequency range that is cut off when

‡

encoding at low bit rate (less than 128Kbps, Sampling frequency is 44.1kHz). Supplementing is optimized by compression format (MP3 or WMA) and processed according to bit rate. The effect is negligible with music that is encoded at high bit rate, variable bit rate or has minimal high frequency range.

• About Dual Zone System

Main source and sub source (Auxiliary input) output Front channel and Rear channel separately.

- When “2Zone” is set to “ON”, the main source sound and AUX input sound are output to the front speakers and rear speakers separately.

- Set up the channel of sub source by “2Zone”.

- Select Main source by [SRC] button.

- Adjust the volume of Front channel by Control knob.

- Adjust the volume of Rear channel by “2Zone Rear Volume”.

- The Audio Control has no effect on sub source.

- When Bluetooth audio source is selected, set “2Zone F/R Select” to “Rear”. “2Zone” cannot be turned “ON” when this is set to “Front”. While “2Zone” is turned “ON”, “2Zone F/R Select” function is disabled.

1 Select the source to adjust

Press the [SRC] button.

For how to select source item, refer to <Power and

source selection> (page 4).

2 Enter Audio Control mode

Press the [AUDIO] button.

3 Select the Audio item to adjust

Turn the Control knob to select the audio item for adjustment and then press the [ENTER] button.

Press the [ ] button to return to the previous item.

4 Adjust the Audio item

Turn the Control knob.

5 Determine the setting value

Press the [ENTER] button.

The previous item is displayed.

6 Exit Audio Control mode

Press the [ ] button for at least 1 second.

English

Audio Adjustments

Audio Preset Memory

Registering the value setup by Audio Control.

1 Setup Audio Control

Setup the <Audio Control> (page 7).

2 Enter Audio Control mode

Press the [AUDIO] button.

3 Select Audio preset memory mode

The item can be selected and determined as follows. “Detailed Settings” ➜ “Audio Preset” To select the item, turn the Control knob. To determine the item, press the [ENTER] button.

4 Select the Audio Preset Memory

Turn the Control knob to select “Memory”, and then press the [ENTER] button.

5 Turn the Control knob to select “YES”, and then

press the [ENTER] button.

“Memory Completed” is displayed.

6 Exit Audio Control mode

Press the [ ] button for at least 1 second.

⁄

• To use this function, this unit must be powered for more

than one hour.

• Register 1 pair of Audio Preset Memory. You cannot register

by the source.

• When you press the Reset, all the sources will be the setting

value which is registered.

• The following items can be registered.

“Bass Center FRQ”, “Bass Level”, “Bass Q Factor”, “Bass EXT”, “Middle Center FRQ”, “Middle Level”, “Middle Q Factor”, “Treble Center FRQ”, “Treble Level”, “SubWoofer Level”, “HPF Front”, “HPF Rear”, “LPF SubWoofer”, “Subwoofer Phase”

Audio Preset Recall

Recalling the sound setup registered by <Audio

Preset Memory> (page 8).

1 Select the source

Press the [SRC] button.

For how to select source item, refer to <Power and

source selection> (page 4).

2 Enter Audio Control mode

Press the [AUDIO] button.

3 Select Audio preset memory mode

The item can be selected and determined as follows. “Detailed Settings” ➜ “Audio Preset” To select the item, turn the Control knob. To determine the item, press the [ENTER] button.

4 Select the Audio Preset Recall

Turn the Control knob to select “Recall”, and then press the [ENTER] button.

5 Turn the Control knob to select “YES”, and then

press the [ENTER] button.

“Recall Completed” is displayed.

6 Exit Audio Control mode

Press the [ ] button for at least 1 second.

KDC-X494/ KDC-MP445U/ KMR-440U

Music disc/Audio file Operation

Function of Audio file/ Internal CD source

Music Search

Selecting the music you want to listen to from the device or media being played now.

1 Enter Music Search mode

Press the [ ] button.

“MUSICSEARCH” is displayed.

2 Search for music

Audio file

Operation type Operation

Movement between folders/files

Selection of folder/flie Press the [ENTER]. Return to previous folder Press the [ Return to root folder Push the Control knob towards left for at

Cancel the Music Search mode

¡ indicator: Audio file ] indicator: Folder with a folder or file in the lower

^ indicator: Folder without a folder or file in the

CD source

Operation type Operation

Movement between track Turn the Control knob. Selection of track Press the [ENTER]. Return to first track Push the Control knob towards left for at

Cancel the Music Search mode

Turn the Control knob.

least 1 second. Press the [

layer

lower layer

least 1 second. Press the [

] button.

] button for at least 1 second.

] button.

Function of iPod source

Music Search for iPod

Searching for the song (in iPod) you want to play.

1 Enter Music Search mode

Press the [ ] button.

“MUSICSEARCH” is displayed.

2 Search for music

Operation type Operation

Movement between items Turn the Control knob. Selection of item Press the [ENTER]. Return to previous item Press the [ Return to Top menu Push the Control knob towards up for at

least 1 second.

Cancelling the Music Search mode

Press the [ ] button for at least 1 second.

] button.

⁄

• If no characters included in a song name can be displayed,

the browse item name and digits are displayed.

Items Display Items Display

Playlists “PLIST***” Podcasts “PDCT***” Artists “ART***” Genres “GEN***” Albums “ALB***” Composers “COM***” Songs “PRGM***”

English

Music disc/Audio file Operation

Function of iPod source

Alphabet Search

You can select an alphabetic character from the list in the browse item (artist, album, etc.) currently selected.

1 Enter Music Search mode

Press the [ ] button.

“MUSICSEARCH” is displayed.

2 Select browse item

Turn the Control knob to select browse item, and then press the [ENTER] button.

3 Enter Search select mode

Press the [S.MODE] button.

4 Select Alphabet Search mode

Turn the Control knob to select “Alphabet Search”, and then press the [ENTER] button.

5 Select the character to be searched for

Operation type Operation

Select the characters Turn the Control knob. Move the cursor to the enter

character position

Push the Control knob towards up or down.

6 Determine the selected character

Press the [ENTER] button.

Start search. When search is completed, the music search mode is selected again at the selected character position.

Cancelling the Music Search mode

Press the [ ] button for at least 1 second.

⁄

• The time of Alphabet search may become long depending

on the number of items (songs) in iPod.

• To search for a character other than A to Z and 1 to 9, enter

“*”.

• If the first character string begins with an article “a”, “an”,

or “the” in the alphabet search mode, it is searched for in defiance of the article.

Function of iPod source/ Music Editor media

Skip Search

The number of songs to be skipped is determined by the ratio of the total number of songs in the list which is selected.

1 Enter Music Search mode

Press the [ ] button.

“MUSICSEARCH” is displayed.

2 Enter Search select mode

Press the [S.MODE] button.

3 Select Skip Search mode

Turn the Control knob to select “Skip Search”, and then press the [ENTER] button.

4 Search for music

Operation type Operation

Movement between items Turn the Control knob. Skip Search Push the Control knob towards up or down. Selection of item Press the [ENTER]. Return to previous item Press the [

Cancelling the Music Search mode

Press the [ ] button for at least 1 second.

] button.

⁄

• Set the ratio with 25 Skip Search in <Function setting>

(page 16).

• Keep pushing Control knob for 3 seconds or longer skips

songs at 10% regardless of the setting.

KDC-X494/ KDC-MP445U/ KMR-440U

Function of iPod source

Direct Search

Searching for music by selecting a browse item and an alphabetic character(s).

Function of iPod source

Related Search

Browsing for music of the same artist or genre as the one being played.

1 Enter Music Search mode

Press the [ ] button.

“MUSICSEARCH” is displayed.

2 Enter Search select mode

Press the [S.MODE] button.

3 Select Direct Search mode

Turn the Control knob to select “Direct Search”, and then press the [ENTER] button.

4 Select browse item

Turn the Control knob to select browse item, and then press the [ENTER] button.

Display Browses item

Playlists

Artists

Albums

Songs

Podcasts

Genres

Composers

5 Select the character to be searched for

Turn the Control knob to select character, and then press the [ENTER] button.

You can select up to three characters.

6 Search for music

Turn the Control knob to select ”DONE”, and then press the [ENTER] button.

A search result list is displayed.

7 Select the music

Turn the Control knob to select music, and then press the [ENTER] button.

Cancelling the Music Search mode

Press the [ ] button for at least 1 second.

1 Enter Related Search mode

Press the [S.MODE] button.

2 Select browsing item

Turn the Control knob and press the [ENTER] button when the desired browse item is selected.

Display Browses music

“Search Artist” Displays the album of the same artist. “Search Album” Displays music in the album in which the one

being played is included. “Search Genre” Displays the artist of the same genre. “Search Composer” Displays the album including music created by the

same composer.

3 Search for music

Operation type Operation

Movement between items Turn the Control knob. Selection of item Press the [ENTER] button. Return to previous item Push the Control knob towards up.

Cancelling the Related Search

Press the [ ] button for at least 1 second.

⁄

• Related search cannot be performed while playing a

Podcast.

• When the music being played has no information on

browsing items or no music was found, “Not Found” is displayed.

English

Music disc/Audio file Operation

Function of iPod source

My Playlist for iPod

You can register your favorite songs to make a playlist. You can register up to ten songs in the playlist.

Registering a song in the playlist

1 Play the song you want to register

Push the Control knob towards up, down, right, and left.

2 Register the song

Press the [ENTER] button for at least 2 seconds.

“## (registration number) Stored” is displayed. You can register up to ten songs.

⁄

• When creating a playlist, you can register the songs stored

in one iPod. If you attempt to register a song by connecting an unregistered iPod, “My Playlist Delete” is displayed. Selecting “YES” deletes the playlist.

• The song displayed during music search can be registered

in the same manner. For the music search procedure, refer to <Music Search for iPod> (page 9).

• If you attempt to register the eleventh song, “Memory Full”

is displayed and you cannot register the song. To register it, delete an unnecessary song.

• Do not register Podcasts. Songs may be registered or played

improperly. For example, unintended songs are registered.

Playing the playlist

1 Display the playlist

Press the [ENTER] button.

“My Playlist” is displayed.

2 Play a song in the playlist

Turn the Control knob to select the song you want to play and then press the [ENTER] button.

“LIST” indicator is displayed.

⁄

• To stop playing the song in the playlist, turn the power off.

• If a song does not end with 1 second or longer silence, its

last portion may not be played.

• Songs cannot be played at random during playback of the

songs in playlist.

Deleting a song from the playlist

1 Display the playlist

Press the [ENTER] button.

“My Playlist” is displayed.

2 Turn the Control knob to select the song you

want to delete and then press the [ENTER] button for at least 2 seconds.

KDC-X494/ KDC-MP445U/ KMR-440U

3 Turn the Control knob to select “One” or “All”,

and then press the [ENTER] button.

Selecting “All” deletes all songs.

4 Turn the Control knob to select “YES”, and then

press the [ENTER] button.

“Completed” is displayed.

⁄

• All songs in the playlist can also be deleted by selecting 26

My Playlist Delete of <Function setting> (page 16).

Function of remote control

Direct Music Search

Searching the music by entering the track number.

1 Enter Direct Music Search mode

Press the [DIRECT] button on the remote control.

“– –” is displayed.

2 Enter the music number

Press the number buttons on the remote control.

3 Search the music

Press the [4] or [¢] button on the remote control.

Cancelling Direct Music Search

Press the [ ] button on the remote control.

⁄

• Direct Music Search cannot be per formed during playing

of iPod.

Function of disc changers

Basic Operation of Disc Changer (Optional)

Selecting CD changer source

Press the [SRC] button.

Select the “CD CH” display. For how to select source item, refer to <Power and

source selection> (page 4).

Music search

Push the Control knob towards right or left.

Disc Search

Push the Control knob towards up or down.

Function of disc changers with remote control

Direct Search in Disc Changer (Optional)

Searching the disc or music by entering the disc or music number.

1 Enter Direct Search mode

Press the [DIRECT] button on the remote control.

“– –” is displayed.

2 Enter the disc or music number

Press the number buttons on the remote control.

3 Search the disc

Press the [FM] or [AM] button on the remote control.

Search the music

Press the [4] or [¢] button on the remote control.

Cancelling Direct Search

Press the [ ] button on the remote control.

⁄

• Input “0” to select disc 10.

English

Tuner Operation

Station Preset Memory

Putting a station in the memory.

1 Select the frequency to put in the memory

Push the Control knob towards right or left.

2 Enter Preset Memory mode

Press the [ ] button.

3 Preset the station

Turn the Control knob to select preset number (“P1” – “P6”), and then press the [ENTER] button for at least 2 seconds.

Cancelling the Preset Memory mode

Press the [ ] button.

Preset Tuning

Recalling the stations in the memory.

1 Enter Preset Tuning mode

Press the [ ] button.

2 Recall the station

Turn the Control knob to select recall number (“P1” – “P6”), and then press the [ENTER].

Cancelling Preset Tuning

Press the [ ] button.

Function of remote control

Direct Access Tuning

Entering the frequency and tuning.

1 Enter Direct Access Tuning mode

Press the [DIRECT] button on the remote control.

“– – – –” is displayed.

2 Enter the frequency

Press the number buttons on the remote control.

Example:

Desired frequency Press button

92.1 MHz (FM) [9], [2], [1] 810 kHz (AM) [8], [1], [0]

3 Search the frequency

Press the [4] or [¢] button on the remote control.

Cancelling Direct Music Search

Press the [ ] button on the remote control.

KDC-X494/ KDC-MP445U/ KMR-440U

+ 31 hidden pages

Kenwood KDC-X494, KDC-MP445U User Manual

Contents

Before use

Basic Operations

General opreration

Removing the Faceplate

Muting the audio upon reception of phone call

Audio Adjustments

Audio Control

Audio Preset Memory

Audio Preset Recall

Music disc/Audio file Operation

Music Search

Music Search for iPod

Alphabet Search

Skip Search

Direct Search

Related Search

My Playlist for iPod

Direct Music Search

Basic Operation of Disc Changer (Optional)

Direct Search in Disc Changer (Optional)

Tuner Operation

Station Preset Memory

Preset Tuning

Direct Access Tuning