Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best
performance from your new DVD Receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty
card, and in the space provided below. Refer to the model and serial numbers whenever you call
upon your Kenwood dealer for information or service on the product.
Model DDX790/DDX770/DDX7070BT/DDX470/DDX4070BT/DDX370/DDX3070 Serial number
US Residence Only
Register Online
Register your Kenwood product atwww.Kenwoodusa.com
• DO NOT install any unit or wire any cable in
a location where;
– it may obstruct the steering wheel and
gearshift lever operations.
– it may obstruct the operation of safety
devices such as air bags.
– it may obstruct visibility.
• DO NOT operate the unit while driving.
If you need to operate the unit while
driving, be sure to look around carefully.
• The driver must not watch the monitor
while driving.
Cautions on the monitor:
• The monitor built in this unit has been
produced with high precision, but it
may have some ineffective dots. This is
inevitable and is not considered defective.
• Do not expose the monitor to direct
sunlight.
• Do not operate the touch panel using a
ball-point pen or similar tool with the sharp
tip.
Press the buttons on the touch panel with
your finger directly (if you are wearing a
glove, take it off).
• When the temperature is very cold or very
hot...
– Chemical changes occur inside, causing
malfunction.
– Pictures may not appear clearly or
may move slowly. Pictures may not
be synchronized with the sound or
picture quality may decline in such
environments.
For safety...
• Do not raise the volume level too much,
as this will make driving dangerous by
blocking outside sounds, and may cause
hearing loss.
• Stop the car before performing any
complicated operations.
Temperature inside the car...
If you have parked the car for a long time
in hot or cold weather, wait until the
temperature in the car becomes normal
before operating the unit.
How to reset your unit
DDX790/DDX770/DDX7070BT
Reset button
DDX470/DDX4070BT/DDX370/DDX3070
Reset button
If the unit fails to operate properly, press
the Reset button. The unit returns to factory
settings when the Reset button is pressed
(except the registered Bluetooth devices).
How to read this manual:
• Illustrations of DDX770 are mainly used
for explanation.
• This manual mainly explains operations
using the buttons on the monitor panel
and touch panel. For operations using the
remote controller (RC-DV340: supplied
only for DDX7070BT/DDX4070BT/
DDX3070
• < > indicates the variable screens/
• [ ] indicates the buttons on the touch
• Indication language: English
The displays and panels shown in this
manual are examples used to provide
clear explanations of the operations. For
this reason, they may be different from the
actual displays or panels.
), ☞ page 66.
menus/operations/settings that appear
on the touch panel.
panel.
indications are used for the purpose
of explanation. You can select the
indication language from the <Setup>
menu. (☞ page
52
)
English 3
Page 4
DDX790/DDX770/DDX470/DDX370:
FCC WARNING
This equipment may generate or use radio
frequency energy. Changes or modifications
to this equipment may cause harmful
interference unless the modifications are
expressly approved in the instruction manual.
The user could lose the authority to operate
this equipment if an unauthorized change or
modification is made.
FCC NOTE
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment may cause harmful interference
to radio communications, if it is not installed
and used in accordance with the instructions.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
DDX790/DDX770/DDX470/DDX370:
CAUTION
Use of controls or adjustments or
performance of procedures other than
those specified herein may result in
hazardous radiation exposure. In compliance
with Federal Regulations, following are
reproductions of labels on, or inside the
product relating to laser product safety.
JVC KENWOOD Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI, TOKYO, JAPAN
THIS PRODUCT COMPLIES WITH DHHS
RULES 21CFR SUBCHAPTER J IN EFFECT
AT DATE OF MANUFACTURE.
Location : Top plate
DDX7070BT/DDX4070BT/DDX3070:
The marking of products using lasers
The label is attached to the chassis/case and
says that the component uses laser beams
that have been classified as Class 1. It means
that the unit is utilizing laser beams that
are of a weaker class. There is no danger of
hazardous radiation outside the unit.
DDX790/DDX770/DDX7070BT/DDX470/
DDX4070BT:
About KS-UBT1 (USB Bluetooth adapter)
The USB Bluetooth adapter is attached to
this unit when shipped from the factory.
When the adapter is removed, store it in a
safe place.
4 English
Page 5
INTRODUCTIONS
Initial S ettings
Initial setup
When you power on the unit for the first time
or reset the unit, the initial setting screen
appears.
• You can also change the settings on the
<Setup> screen. (☞ page 50)
1 For DD X790/DDX770/DDX7070BT :
For DD X470/DDX4070BT/DDX3070 :
For DDX370:
Language Select the text language
Angle *
AV InputSelect an external
External
BUS *
R-CAM
Interrupt
Panel
Color
used for on-screen
information. (☞ page 52)
• Set <GUI Language>
to display the operation
buttons and menu
items in the selected
language ([Local]:
initially selected) or
English ([English]).
1
Adjust the panel angle.
(☞page 11)
component to play —
[AV-IN2] or [iPod]. (☞
page 52)
Select the component
2
connected to EXT I/F
input terminal — [OEM]
for ADS adapter or [SXi]
for SiriusXM Connect
Vehicle Tuner. (☞ page 52)
Select [ON] when
connecting the rear view
camera. (☞ page 52)
Select the color of the
buttons on the monitor
panel. (☞ page 45)
2 Finish the procedure.
1
*
Only f or DDX790/DDX770/DDX7070BT.
2
*
Only f or D DX370 .
English 5
Page 6
Updating the system
You can update the system by connecting a
USB device containing the update file.
1 Create an update file, copy it
to a USB device, and connect
it to the unit.
To connect a USB device, ☞ p age 8 2 .
2 On <Top Menu>:
3
4
6 English
Application
Version
DVD Version Updates the DVD
It may take a while.
If the update has been complete
successfully, “Update Completed”
appears. Reset the unit.
• If the update has failed, turn the power off
and then on, and retry the update.
• Even if you have turned off the power
during update, you can restart the update
after the power is turned on. The update
will be performed from the beginning.
Updates the System
application.
System application.
Page 7
Activating the security
function
You can activate security function to protect
your receiver system against theft.
1 On <Top Menu>:
2
The security indicator on the monitor
panel flashes when the vehicle ignition
is off.
To cancel, select [OFF].
English 7
Page 8
Component names and functions
DDX790/DDX770/DDX7070BT
Screen (Touch panel)Monitor panel
1 Reset button/Power indicator/Security
indicator
• Resets the unit. (☞ page 3)
• Lights up while the unit is turned on.
• Flashes when the security function is
activated. (☞ page 7)
2 ATT button (Press)
• Attenuates the sound.
V.OFF button (Hold)
• Turns off/on the screen. (☞ page 12)
3 VOLUME
• Decreases the volume.
4 VOLUME (up) button (☞ page 11)
• Increases the volume.
5 AUD button (Press)
• Displays the <Tone> screen. (☞ page
43)
R-CAM button (Hold)
• Displays the picture from the rear view
camera.
(down) button (☞ page 11)
6 AV button (Press)
• Displays the current source screen.
AV OUT button (Hold)
• Selects the AV source for external
monitor or amplifier.
7
MENU button
• Turns off the power. (Hold)
• Turns on the power. (Press)
• Displays the <Top Menu> screen.
(Press) (☞ page 13)
8 TEL button (Press)
• Displays the <Handsfree> screen. (☞
page 60)
VOICE button (Hold)
• Activates voice dialing. (☞ page 60)
90 (Eject) button
• Ejects the disc (Tilts the monitor panel
fully).
• Opens/Closes the monitor panel.
p Remote sensor
Caution on the volume setting:
Digital devices produce very little noise
compared with other sources. Lower
the volume before playing these digital
sources to avoid damaging the speakers
by sudden increase of the output level.
8 English
You can change the color of the buttons
on the monitor panel. (☞ page 45)
Page 9
DDX470/DDX4070BT/DDX370/DDX3070
Screen (Touch panel)Monitor panel
1 Loading slot
2 0 (Eject) button
• Ejects the disc.
3 Reset button/Power indicator/Security
indicator
• Resets the unit. (☞ page 3)
• Lights up while the unit is turned on.
• Flashes when the security function is
activated. (☞ page 7 )
4 Remote sensor
5
MENU button
• Turns off the power. (Hold)
• Turns on the power. (Press)
• Displays the <Top Menu> screen.
(Press) (☞ page 13)
6 AV/AV OUT button
• Displays the current source screen.
(Press)
• Selects the AV source for external
monitor or amplifier. (Hold)
If you insert a DVD Video disc of an incorrect Region Code, “Region code error” appears on the screen.
2
*
DVD-R recorded in multi-border format is also playable (except for dual layer discs). DVD-RW dual layer
discs are not playable.
3
*
It is possible to play back finalized +R/+RW (Video format only) discs. “DVD” is selected as its disc type
when a +R/+RW disc is loaded. +RW double layer discs are not playable.
4
*
This unit cannot play back contents protected with CPRM (Content Protection for Recordable Media).
5
*
Playable only for DDX7070BT/DDX4070BT/DDX3070.
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio”
standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be
recommended.
1
4
5
/MPEG1/MPEG2
English 17
Page 18
Playback o perations
To display the source control screen, ☞ page 14.
For D VD/DVD-VR/VCD/DivX/MPEG1/MPEG2/JPEG
Media typePlaying time
• DVD Video: Title no./Chapter no.
• DVD-VR: Program no. (or Playlist
no.)/Chapter no.*
• DivX/MPEG1/MPEG2: Folder no./
Track no.
• JPEG: Folder no./File no.
• VCD: Track no.
File type (for DivX/MPEG1/MPEG2/JPEG)
Playback mode
[]
[
]*
[38]Starts/pauses playback.
3
[7]*
[4] [¢] • Selects a chapter/track.
• For DivX/MPEG1/MPEG2/JPEG, the following buttons also appear:
[ ] [ ]Selects a folder.
Selects playback mode.
2
(☞ page 21)
Stops playback.
(Press)
• Reverse/forward search.*
(Hold)
[1] [¡] • Reverse/forward search
5
[MODE]*
4
[MENU]Displays the <Top Menu>
[]
1
during playback.*
4
• Plays back in slowmotion during pause.
Enters the <DISC Mode>
settings. (☞ page 22)
screen.
Displays the folder/track
list. (☞ page 19)
1
*
To display the Original Program/Playlist screen, ☞ page 20.
2
*
Does not appear for DVD/DVD-VR/JPEG.
3
*
Appears only for DVD/DVD-VR/VCD.
4
*
Search speed varies depending on the type of disc or file.
5
*
Does not appear for VCD.
18 English
Page 19
For CD/MP3/WMA/WAV/AAC
While playing, the jacket picture is shown if the
file has the tag data including the jacket picture.
Media type
File type
Playback mode
• MP3/WMA/WAV/AAC: Folder no./Track no.
• CD: Track no.
Playback status (3: play / 8: pause )
Playing time
Track/file information
• Pressing [<] scrolls the
text if not all of the text
is shown.
[] []
Selects playback mode.
(☞ page 21)
1
[
] *
Displays the folder/track list.
(☞ below)
[38]Starts/pauses playback.
] [ ]*1Selects a folder.
[
1
*
Does not appear for CD.
2
*
Search speed varies depending on the type of disc or file.
Selecting folder/track on the list
Returns to the
Returns to the root folder
Changes the page
upper layer
Plays tracks/files in
the folder
[4] [¢] Selects a track.
[1] [¡]Reverse/forward search.*
2
[MODE] *1Enters the <DISC Mode>
settings. (☞ page 22)
[MENU]Displays the <Top Menu>
screen.
Playing Recordable/Rewritable discs
• This unit can recognize a total of 5 000
files and 250 folders (a maximum of 999
files per folder).
• Use only “finalized” discs.
• This unit can play back multi-session
discs; however, unclosed sessions will be
skipped while playing.
• Some discs or files may not be played
back due to their characteristics or
recording conditions.
English 19
Page 20
Video menu operations
You can display the video menu screen
during video playback.
• Available items on the screen differ
depending on the types of the loaded disc
and playback files.
• The operation buttons disappear by
touching the screen or when no operation
is done for about 5 seconds.
• The screen for MPEG1/MPEG2 differs from
the above.
ZOOMDisplays the picture size
Aspect
Picture
Adjust
AudioSelects the audio type.
SubtitleSelects the subtitle type.
AngleSelects view angle.
MENUDisplays the disc menu
T MENUDisplays the disc menu
HighlightSwitches to the direct disc
CURDisplays the menu/playlist/
selecting screen. (☞ page 48)
Selects the aspect ratio. (☞
page 48)
Displays the picture
adjustment screen. (☞
page 47)
• For DVD-VR: Selects the
audio channel (ST: stereo,
L: left, R: right).
(DVD)/playlist (DVD-VR).
(DVD)/original program
(DVD-VR).
menu mode. Press the target
item to select.
• To restore the screen, press
AV on the monitor panel.
original program item
selecting screen.
• [5] [∞] [2] [3]: Selects an
item.
– For DivX only
[2] [3]: Skips back or
forward by about 5
minutes.
• [ENTER]: Confirms the
selection.
• [RETURN]: Returns to the
previous screen.
20 English
Page 21
Only for VCD
1
• To deactivate the PBC function, press [7]
then the direct selecting buttons to select
a track number.
Selecting playback mode
For DVD/DVD-VR
Selects Repeat playback mode
2
Direct selecting buttons (☞ below)
ZOOMDisplays the picture size
Aspect
Picture
Adjust
MENUDisplays the disc menu.
AudioSelects the audio channel (ST:
DirectDisplays/hides the direct
ReturnDisplays the previous screen or
• To select a track directly
selecting screen. (☞ page 48)
Selects the aspect ratio. (☞
page 48)
Displays the picture adjustment
screen. (☞ page 47)
stereo, L: left, R: right).
selecting buttons. (☞ below)
the menu.
For VCD (without PBC)/CD/DivX/MPEG1/
MPEG2/MP3/WMA/WAV/AAC
Selects Repeat playback mode*
Selects Random playback
mode*
* You cannot activate the repeat mode and the
random mode at the same time.
• Each time you press the button,
the playback mode changes. (The
corresponding indicator lights up.)
– Available items differ depending on the
types of loaded disc and playback file.
IndicatorPlayback mode
C-REPRepeats current chapter.
T-REPRepeats current title/
program.
REPRepeats current track.
FO-REPRepeats all tracks of the
current folder.
RDMRandomly plays all tracks.
FO-RDMRandomly plays all tracks of
current folder, then tracks of
next folders.
To cancel, press the button repeatedly until
the indicator disappears.
• Avoid using the USB device if it might
effect driving safety.
• Do not pull out and connect the USB
device repeatedly while “Reading...” is
shown on the screen.
• Electrostatic shock at connecting a USB
device may cause abnormal playback of
the device. In this case, disconnect the USB
device then reset this unit and the USB
device.
• Operation and power supply may not work
as intended for some USB devices.
• Do not leave a USB device in the car,
or expose to direct sunlight or high
temperature to avoid deformation or
damage to the device.
English 23
Page 24
• To display the source control screen, ☞ page 14.
• To change settings for video playback, ☞ page 20.
• Pressing [<] scrolls
the text if not all of
the text is shown.
Displays the folder/track list.
(☞ page 19)
settings. (☞ below)
screen.
• Available items differ depending on the types of playback file.
1
*
To cancel random or repeat mode, press the button repeatedly until the indicator disappears.
2
*
You cannot activate the repeat mode and the random mode at the same time.
3
*
Search speed varies depending on the type of disc or file.
3
<USB Mode> settings
Setting <Screen Ratio>
Select the monitor type to watch a wide
screen picture on the external monitor.
16:94:3 LB
(Letterbox)
Setting <Drive Select>
Press [Next]. Switches between internal and
external memory source of the connected
device (such as mobile phone).
24 English
4:3 PS
(PanScan)
Setting <File Type>
AudioPlays back audio files.
Still ImagePlays back JPEG files.
VideoPlays back DivX/MPEG1/
MPEG2 files.
Audio&Video Plays back audio files and
DivX/MPEG1/MPEG2 files.
• If the USB device contains no files of the
selected type, the existing files are played
in the following order: audio, video, then
still image.
Page 25
Listening to the iPod/iPhone device
Preparation
• Connect iPod/iPhone. (☞ p age 82 )
– When connecting iPhone/iPod touch,
turn off App beforehand; otherwise
the playback may not be started after
connection.
• Use the following cables:
–
To watch the video and to listen to
the music (analog): USB Audio and
Video cable for iPod/iPhone—
(optional accessory)
– To listen to the music (digital): USB
Audio cable for iPod/iPhone—KCA-iP102
(optional accessory)
• Select appropriate input settings on <AV Input> according to the connection
method (☞ the right column)
• Do not use extension cables.
iPod/iPhone that can be connected to this
unit:
Made for
– iPod with video
– iPod classic
– iPod nano (6th Generation)
– iPod nano (5th Generation)
– iPod nano (4th Generation)
– iPod nano (3rd Generation)
– iPod touch (4th Generation)
– iPod touch (3rd Generation)
– iPod touch (2nd Generation)
– iPod touch (1st Generation)
– iPhone 4S
– iPhone 4
– iPhone 3GS
– iPhone 3G
– iPhone
KCA-iP202
Settings for iPod playback
When the source is “
iPod
”...
1
2
AudiobooksSelects the speed of
audio books.
ArtworkShows/hides the iPod
artwork.
Setting <AV Input> for iPod/iPhone
playback
You can change the setting only when
[STANDBY] is selected on <Top Menu>.
(☞ page 12)
1 On <Top Menu>:
2
AV-IN2 Select this when connecting
the iPod/iPhone using the
USB Audio cable for iPod/
iPhone.
iPodSelect this when connecting
the iPod/iPhone using the
USB Audio and Video cable
for iPod/iPhone
English 25
Page 26
iPod/iPhone playback operations from the unit
• To display the source control screen, ☞ page 14.
• To change settings for video playback, ☞ page 20.
While playing,
Artwork (the
picture displayed
on the screen
of iPod/iPhone)
is shown if the
song contains the
Artwork.*
1
Track no./total track no.
[MODE] Enter the <iPod Mode>
settings. (☞ page 25)
[38]Starts/pauses playback.
]Selects Repeat playback
[
mode. *
2
• REP: Functions the same as
“Repeat One.”
[
Selects Random playback
]
mode. *
2
• RDM: Functions the same as
“Shuffle Songs.”
Playback mode
Playback status (3: play / 8: pause )
Playing time
Song/video
information
• Pressing [<] scrolls
the text if not all of
the text is shown.
[]
[4]
Displays the audio/video file
list. (☞ page 27)
Selects an audio/video file.*
[¢]
[1]
Reverse/forward search.
[¡]
[APP] Select to control playback from
the iPod/iPhone—iPod/iPhone
control mode.*
[MENU] Displays the <Top Menu>
screen.
• A-RDM: Functions the same
as “Shuffle A lbums.”
1
For changing the Artwork display setting, ☞ page 25.
*
2
*
To cancel random or repeat mode, press the button repeatedly until the indicator disappears.
Not available in iPod control mode. (
3
*
Resume playback is unavailable for video files.
4
*
When using iPod with video, you can control playback only from the unit.
☞ page 27)
• When you turn on this unit, the iPod/iPhone is charged through the unit.
• The text information may not be displayed correctly.
4
(☞ page 27)
3
• For some iPod/iPhone models, the performance may be abnormal or unstable during
operation. In this case, disconnect the iPod/iPhone device, then check its condition.
If the performance is not improved or is slow, reset your iPod/iPhone.
• For the latest compatible list and software version of iPod/iPhone, see:
www.kenwood.com/cs/ce/ipod
26 English
Page 27
Selecting an audio/video file
from the menu
1
2 Select the menu (audio or
video) (1), a category (2),
then a desired item (3).
• Select the item in the selected layer
until a desired file starts playing.
Audio menu:
Returns to the top layer
Switches between audio
) and video ( )
(
Returns to the
previous layer
Controlling playback from
the iPod/iPhone
You can play back the audio/video files or use
App by operating iPod/iPhone itself instead
of the unit.
• When you are using Garmin StreetPilot®
Onboard, the screen appears. For Garmin
StreetPilot® Onboard for iPhone, visit the
Garmin web site: www.garmin.com
Garmin App:
Changes the page
Video menu:
Switches between audio ( ) and video ( )
• Available categories differ depending on
the type of your iPod/iPhone.
Starts folder playback
• The current position of your vehicle
appears on the map. When the vehicle
runs, the map scrolls.
• The screens of the iPhone and unit are
not the same.
• To return to the normal mode, press [APP].
English 27
Page 28
Listening to the radio
Band no./preset no./the
station frequency currently
tuned in
Text information
• Pressing [<] scrolls the text if
not all of the text is shown.
ST/MONO indicator
Press to switch the information between Radio Text, Radio Text Plus, and PTY code.
TI indicator
Seek mode indicator
• The ST indicator lights up when receiving an FM stereo broadcast with sufficient signal
strength.
[P1] – [P6] • Selects a stored station.
(Press)
• Stores the current station.
(Hold)
[MODE]Enters the <Tuner Mode>
[PTY] *Enters the PTY search mode.
(☞ page 30)
[AM]Selects AM band.
[FM]Selects FM band.
settings. (☞ page 29)
[TI] Activates/deactivates TI
standby reception mode.
(☞ page 30)
[MONO] * Activates/deactivates
monaural mode for better FM
reception. (Stereo effect will
be lost.)
• The MONO indicator lights
up while monaural mode is
activated.
[TEXT]Displays/hides the
information of the current
[SEEK]Changes the seek mode.
• AUTO1: Auto Search
• AUTO2: Tunes in stations
in memory one after
another.
• MANU: Manual Search
[4]
[¢]
Searches for a station.
• The search method differs
according to the selected
seek mode. (☞ above)
[MENU]Displays the <Top Menu>
screen.
station. (☞ page 29)
*
Appears only when FM is selected as the source.
28 English
Page 29
Changing the display information
PS (station name) for FM RBDS when PS
signal is coming in
Preset list
Displays the text
information
Manual p resetting
1 Tune in to a station you want
to preset. (☞ page 28)
2 Select a preset number.
(Hold)
Storing stations in memory
You can preset six stations for each band.
Automatic p resetting — AME ( Auto
Memory)
1
2
(Hold)
Local stations with the strongest signals are
searched and stored automatically.
The station selected in step
Selecting a preset station
1 is stored.
English 29
Page 30
The following features are available only
for FM RBDS stations.
Searching for FM RBDS
program—PTY Search
You can search for your favorite programs
being broadcast by selecting the PTY code.
1
2 Select a PTY code.
(Hold)
Changes the page
PTY Search starts.
If there is a station broadcasting a
program of the same PTY code as you
have selected, that station is tuned in.
Activating/deactivating TI
Standby Reception
TI indicator
TI indicatorTI Standby Reception
Lights in
white
Lights in
orange
Goes offDeactivated.
• The volume adjustment for Traffic
Information is automatically memorized.
The next time the unit switches to Traffic
Information, the volume is set to the
previous level.
The unit will temporarily
switch to Traffic Information
(TI) if available.
Not yet activated. Tune in to
another station providing the
RBDS signals.
30 English
Page 31
Listening to the SiriusXM™ Satellite Radio
(Only for DDX790/DDX770/DDX470/DDX370)
Everything worth listening to is on SiriusXM, getting over 130 channels, including the most
commercial-free music, plus the best sports, news, talk and entertainment. To start listening
to the SiriusXM™ Satellite Radio, a SiriusXM Connect Vehicle Tuner (sold separately) and
subscription are required. For more information, visits www.siriusxm.com.
Only for DDX370
Preparation: Select <SXi> for <External BUS> while [STANDBY] is selected on <Top
Menu> so that <SXi> is selectable as the source on <Top Menu> (☞ page 52).
Band no./Radio ID* (or Preset no.
if the current station is preset)/
Channel Number
Text information
• Pressing [<] scrolls the text if
not all of the text is shown.
Signal reception indicator
Seek mode indicator
* The Radio ID is displayed when the channel is set to 0.
[P1] – [P6]• Selects a stored
[Song Title]
[Content Info]
[Category]
[MODE]Enters the <SiriusXM
[DIRECT] Displays the <Direct
[TEXT]Displays/Hides the
[REPLAY]Displays the <Replay>
channel. (Press)
• Stores the current
channel. (Hold)
Changes the displayed
information each time
this button is pressed.
Mode> settings.
(☞ page 36)
Channel Select> screen.
(☞ page 33)
information on the
current channel.
(☞ page 33)
screen. (☞ page 35)
[]
[BAND]Changes the band.
[SEEK]Changes the seek mode.
[4] [¢]Seeks forward or
[MENU]Displays the <Top
Obtain information
on channels or select
a category and then a
channel.
(☞ page 34)
SXM2
SXM1
SXM4 SXM3
• SEEK1: Skip to another
available channel.
• SEEK2: Skip to another
preset channel.
backward (refer to the
above for the seek mode).
Menu> screen.
English 31
Page 32
Radio activation
SiriusXM Satellite Radio operation requires
the connection of the optional SiriusXM
Connect Vehicle Tuner (sold separately). To
activate the SiriusXM Connect Vehicle Tuner,
you will need the Radio ID.
1 Make a note of your Radio ID.
For each SiriusXM Connect Vehicle Tuner,
peculiar Radio ID is assigned. To confirm
your Radio ID, tune to channel 0.
• The letters I, O, S and F are not used in
any Radio ID.
2 Activate your SiriusXM
Service:
Go to www.siriusxm.com/
activatenow or call 1-866-6352349 to activate your SiriusXM
Connect Vehicle Tuner.
3 When the following screen
appears, press [Enter].
32 English
Page 33
Changing the display
information
Displays the text
Preset list
information
Storing channels in memory
You can preset six channels for each band.
(24 in total)
1 Tune in to a channel you want
to preset. (☞ page 31)
2 Select a preset number.
Selecting a preset channel
Selecting a channel directly
1
2 Enter a channel no. (1), and
then confirm (2).
• To clear the entry, press [Clear].
• To cancel selecting the channel, press
[Cancel].
(Hold)
The channel selected in step
1 is stored.
English 33
Page 34
Displaying information on
channels
You can obtain information on channels or
select a category and then a channel.
1
2 Select [Preset List] or [Channel
List].
3
Preset List
Select a band (1) and then a preset
channel (2).
Channel List
Select a category (1) and then a channel
(2).
Changes the page
– To list all the channels, select [All
Channels].
– Pressing the info change button
above the list displays information in
the following order:
Channel Name = Artist Name =
Song Title = Content Info
Info change button
34 English
Page 35
Using the Replay function
You can temporarily record the broadcast
from the current time, and replay the
recorded data.
• When the recording capacity is full,
the older recorded data is deleted and
recording continues.
• If you change to another channel during
playback, the recorded content will be lost.
Entering the Replay mode
Time code
Progress barPlayback status
(3: play / 8: pause )
Progress
bar
Time code Shows you the point of Replay
[4]• Returns to the previous
[1] [¡] Rewind/Fast forward
[38]Starts/Pauses playback.
[¢]Skips the current track.
Shows the remaining capacity
(gray) and the amount of
recorded data (blue). If you
have already recorded fully,
the entire bar is indicated in
blue.
• Updated every second.
you are listening to.
• Example: –5:00
You are listening to the data
of 5 minutes before the
current broadcast.
• Updated every second.
track if pressed within
2 seconds from the
beginning of the current
track.
• Returns to the beginning of
the current track if pressed
after 2 seconds or more
of the track have been
replayed.
Exiting the Replay mode (Returning to
the channel reception screen)
English 35
Page 36
Setting the reception
restrictions
Display the <SiriusXM Mode> screen to
configure the settings.
Setting the parental lock
You can set the parental lock or parental
mature lock in order to, for example, restrict
children from receiving adult channels.
Setting/Changing the parental code
• Changing the code does not change the
<Parental Mature Lock>/<Parental Lock Channel>/<Channel Skipping>
settings.
1
3 Enter a new four-digit code
(1), and then confirm (2).
• To clear the entry, press [Clear].
• To cancel setting the code, press
[Cancel].
4 Enter the four-digit code and
then press [Enter] again to
confirm the code.
Activating/Deactivating the parental
mature lock
You can set the parental lock on channels
classed as “adult” by SiriusXM™.
• To enable the parental control based
on Mature channels, press [ON] next to
<Parental Mature Lock>.
• To release the lock, press [OFF].
2 Enter a four-digit code (1),
and then confirm (2).
• To clear the entry, press [Clear].
• To cancel setting the code, press
[Cancel].
• The initial setting is “0000”.
36 English
Enter the parental code to confirm your
choice.
Page 37
Activating the parental lock on each channel
This parental control option allows you
to pick the channels to be locked by the
parental control feature.
1
Skipping unwanted channels
If you do not want to receive some channels,
you can skip them.
Activating the channel skipping
1
2 Enter the parental code.
3 Select a category (1) and
then a channel (2).
• To list all the channels, select [All
Channels].
• A checkmark appears beside the
selected channel.
Repeat this step if you want to set the
lock on multiple channels.
• Checkmarks appear beside the locked
channels, and the channels are
disabled.
Deactivating the parental lock
2 Select a category (1) and
then a channel (2).
• To list all the channels, select [All
Channels].
• A checkmark appears beside the
selected channel.
Repeat this step if you want to skip
multiple channels.
Clearing the channel skipping
(Hold)
All the skipped channels will be cleared.
Enter the parental code.
All the locked channels will be
deactivated.
English 37
Page 38
Pandora® o perations
(Only for DDX790/DDX770/DDX470/DDX370 )
• You can operate Pandora using the remote controller. Only playing, pausing, and skipping
are available.
• Install the latest version of the Pandora application on your iPhone/iPod touch/Android/
BlackBerry.
Playback status (3: play / 8: pause )
Playing time
The picture data
is displayed if
available from the
current content
and when iPhone/
iPod touch is
connected via USB.
Song information
• Pressing [<] scrolls
the text if not all of
the text is shown.
[]
[
Displays the list selecting
screen. (☞ page 39)
Displays the connection
]
mode selection screen.
(☞ page 39)
[
Thumbs down to the current
]
song and skips to the next
song.
[38]Starts/Pauses playback.
[¢]Skips the current song.
• Not available when the
Pandora skip reaches its
limit.
38 English
[ ]
[
[
[
[
Registers the current song as
favorite.
Adds the current artist to the
]
Station List.
Adds the current song to the
]
Station List.
Bookmarks the artist.
]
Bookmarks the current song.
]
[MENU]Displays the <Top Menu>
screen.
Page 39
Selecting a device to connect for
Pandora reception (Only for DDX790/
DDX770/DDX470 )
You can connect the device for Pandora
reception either with Bluetooth connection
or wired connection. Select the connecting
method.
• For Bluetooth connection, ☞ page 56.
• For wired connection, ☞ page 82 .
3 Select a station from the list.
On the Station List:
BluetoothSelects to connect Android/
BlackBerry via Bluetooth.
WiredSelects to connect iPhone/
iPod touch via USB.
Selecting a station from the list
1 Display the list selecting
screen.
2 Select the list type.
Shuffle Plays all the songs in the
By Date Sorts the list in reverse
By
Name
On the Genre List:
Select a genre (1), then a station (2).
Changes the page
registered stations randomly.
chronological order.
Sorts the list in alphabetical
order.
Station
List
Genre
List
Selects from the station
names (Station List).
Selects from the genre
names (Genre List).
English 39
Page 40
Requirements for Pandora®
iPhone or iPod touch
• Use an Apple iPhone or iPod touch running under iOS3 or later.
• Install the latest version of the Pandora application on your iPhone or iPod touch. (Search
for “Pandora” in the Apple iTunes App Store to find and install the most current version.)
• Connect iPhone/iPod touch to this unit with a KCA-iP202.
Android™
• Visit the Google play and search for Pandora to install.
• Bluetooth must be built in and the following profiles must be supported.
– SPP (Serial Port Profile)
– A2DP (Advanced Audio Distribution Profile)
BlackBerry®
• Visit www.pandora.com from the built in browser to download the Pandora application.
• Bluetooth must be built in and the following profiles must be supported.
– SPP (Serial Port Profile)
– A2DP (Advanced Audio Distribution Profile)
NOTE
• Ensure you are logged in to your smartphone application. If you do not have a Pandora
account, you can create one for free from your smartphone or at www.pandora.com.
• Pandora is available only in the U.S./Australia/New Zealand.
• Because Pandora is a third-party service, the specifications are subject to change without
prior notice. Accordingly, compatibility may be impaired or some or all of the services
may become unavailable.
• Some functions of Pandora cannot be operated from this unit.
• For issues using the application, please contact Pandora at pandora-support@pandora.
com
• Establish an internet connection by LTE, 3G, EDGE, or WiFi.
40 English
Page 41
Using other external components
AV-IN
To display the source control screen, ☞ page 14.
AV-IN name ( ☞ below)
[MODE]Changes the AV-IN name.
[MENU]Displays the <Top Menu> screen.
You can connects external components to the AV-IN1 and iPod/AV-IN2 input terminals.
Preparation:
If you want to use “
• No preparation is required for “
• Press [2] or [3] to select an AV-IN name.
• This setting does not affect the source name “
displayed on <Top Menu>.
To connect external components,
☞ p ages 82 and 8 3 .
2 Select “AV-IN 1” or “AV-IN 2” as
the source. (☞ page 14)
3 Turn on the connected
component and start playing
the source.
English 41
Page 42
Using the external navigation unit
(Only for DDX7070BT/DDX4070BT/DDX3070)
You can connect a navigation unit ( KNA-G630 : optional accessory) to the navigation input
terminal so that you can view the navigation screen. (☞ p age 83 )
The navigation guidance comes out of the front speakers even when you listen to an audio
source.
To view the navigation
screen
On <Top Menu>:
or
On any screen:
The navigation screen is activated.
• While the navigation screen is displayed,
the touch panel operations are available
only for using navigation function.
• The aspect ratio of the navigation screen
is fixed to <FULL> regardless of the
<Aspect> setting (☞ page 48).
To cancel the navigation screen
DDX7070BT
DDX4070BT/
DDX3070
Settings for navigation unit
1 On <Top Menu>:
2
3
GuidanceSelect front speakers
used for the navigation
guidance.
VolumeAdjust the volume of the
navigation guidance. (0
to 35)
NAV Mute Select [ON] to attenuate
the sound coming out
of speakers other than
the front speakers during
navigation guidance.
NAV Setup Press [Enter] to display
the setup screen for
the navigation unit.
See the instruction
manual supplied for the
navigation unit.
42 English
Page 43
Sound adjustment
Using the sound equalization
• The adjustment is memorized for each source until you adjust the sound again. If the source
is a disc, the adjustment is stored for each of the following categories.
– DVD/DVD-VR/VCD
– CD
– DivX/MPEG1/MPEG2/MP3/WMA/WAV/AAC
• You cannot adjust the sound when the unit is in standby.
Selecting a preset sound
mode
1 On <Top Menu>:
2
3 Select a sound mode.
Changes the page
Storing your own
adjustment
Customizing preset sound mode
1 Select a sound mode. (☞
“Selecting a preset sound mode”)
2 Set <SystemQ- Ex> to [OFF]
(1), then press [Tone] (2).
3 Adjust the level of each band
(1), then select the subwoofer
level * (2).
Selects the band
The adjustments are stored and <User>
is activated.
• You can also display the <Tone> screen
by pressing AUD ( for DDX790/DDX770/
DDX7070BT/DDX370/DDX3070 ) o r VOL/
ATT/AUD knob ( for DDX470/DDX4070BT )
on the monitor panel.
*
Adjustable only when the subwoofer is activated.
(
☞ page 50)
English 43
Page 44
Adjusting the sound precisely
1 Perform steps 1 and 2 of
“Selecting a preset sound
mode,” then...
Adjusting the crossover
frequency
1 On <Top Menu>:
2
3 Adjust the sound of each
band.
Selects the band
FlatChanges level of Bass/
Frequency Selects frequency.
LevelAdjusts level.
Q FactorAdjusts the width of the
Bass EXTActivates/deactivates
SW LevelAdjusts subwoofer level.*
The adjustments are stored and <User>
is activated.
*
Adjustable only when the subwoofer is activated.
(
☞ page 50)
Middle/Treble to 0.
frequency.
bass.
2
3 Select the item to adjust, then
make adjustment.
Adjusts the crossover for front or rear
speakers (high pass filter).
Adjusts the crossover for subwoofer (low
pass filter).*
Adjusts the subwoofer level.
Selects the phase for the subwoofer. *
1
*
Adjustable only when the subwoofer is
activated. (
2
*
Not selectable when <Freq> is set to
<Through>.
1
Adjusts the cross over frequency.
2
☞ page 50)
44 English
Page 45
Changing the display design
You can change the background and panel color.
1 On <Top Menu>:
2
3 Select an item to change
([Background] or [Panel
Color]).
4 Select a background/panel
color.
To select a background
To select a panel color
Variable color illumination
• Illumination color changes gradually.
For making your own color adjustment,
☞ below
Making your own color adjustment
• You can make your own color adjustment
only when <User> is selected.
1
2
3
User color adjuster: You can make your
own color adjustment stored in <
User>.
For setting your favorite scene as the
background,
☞ page 46
Dimmer setting: You can make the color
adjustment for each dimmer setting.
English 45
Page 46
Using your favorite scene as the
background
While playing a video or JPEG, you can
capture an image and use the captured
image as a background.
• You cannot capture copyrighted content
and images from iPod/iPhone .
• When using a JPEG file as the background,
make sure that the resolution is 800 x 600
pixels.
• The color of the captured image may look
different from that of the actual scene.
1 Play a video or JPEG.
2 Display the <User Customize>
screen. (☞ page 45)
3
4 Adjust the image.
[38]*Starts/Pauses playback.
3]*Advances scenes frame-by-
[
[
[5] [∞]
[2] [3]
• To cancel the capture screen, press
*
frame.
Magnifies the scene.
]
(<OFF>, <Zoom1> –
<Zoom3>)
Moves the zooming frame.
[Cancel].
Not displayed when playing an external
component connected to AV-IN1 or iPod/
AV-IN2 input terminal.
5 Capture the image displayed
on the screen.
46 English
A confirmation message appears. Press
[Yes ] to store the newly captured image.
(The existing image is replaced with the
new one.)
• Press [No] to return to the previous
screen.
Page 47
Setting for video playback
You can change the setting for video playback.
Picture adj ustment
You can adjust the picture quality.
1 Display the adjustment menu.
2 Select [DIM ON] (dimmer on)
or [DIM OFF] (dimmer off).
3 Adjust the picture (–15 to
+15).
Adjusts the brightness
Adjusts the contrast
Adjusts the blackness
Adjusts the color
Adjusts the tint*
Adjusts the sharpness
* Adjustable only when the incoming signal is
NTSC.
English 47
Page 48
Changing the aspect ratio
You can change the aspect ratio for video
playback.
1
2
4:3 signal16:9 signal
FULL*:
For 16:9
original
pictures
JUST:
For 4:3LB
original
pictures
Normal*:
For 4:3 original
pictures
Auto:• For “
*
While DivX is played back with <Screen Ratio>
set to <16:9> (for disc:
page 24), the aspect ratio is not set correctly.
DISC
”/”
USB
The aspect ratio is
automatically selected
to match to the
incoming signals.
☞ page 22/ for USB: ☞
” only:
Zooming p icture
You can zoom the picture (<Zoom1> to
<Zoom3>).
• When <Aspect> is set to <JUST> or
<Auto> (☞ the left column), the picture
is zoomed with the aspect ratio of the
<FULL> setting.
1
2
[5] [∞] [2] [3] : Moves the zooming
frame.
48 English
Page 49
Using a rear view camera
• To use a rear view camera, the REVERSE lead connection is required. For connecting a rear
view camera, ☞ p age 83.
Activating the rear view
camera
1 On <Top Menu>:
2
To deactivate, select [OFF].
Displaying the picture from
the rear view camera
The rear view screen is displayed when you
shift the gear to the reverse (R) position.
To display the picture from the rear
view camera manually
DDX790/DDX770/
DDX7070BT
(Hold)
DDX470/
DDX4070BT *
When displaying the picture from the rear
view camera manually, you can change the
setting of the picture. (
To erase the rear view screen, press and
hold the same button again.
1
*
This operation works only when <TEL Key Long Press> is set to <R-CAM>. (
2
*
This operation works only when <AUD Key Long Press> is set to <R-CAM>. (
1
DDX370/DDX3070 *
(Hold)(Hold)
☞ pages 47 and 48 )
☞ p age 5 3 )
☞ p age 5 3 )
2
• To erase the caution message, touch the
screen.
English 49
Page 50
Setting menu items
• You cannot change <Audio> settings when [STANDBY] is selected on <Top Menu>.
(☞ page 12)
Menu itemSelectable setting/itemInitial: Underlined
Fader/BalanceFader : Adjust the front and rear speaker output balance.
♦F6 to R6; Initial 0
• When using a two-speaker system, set the fader to the
center (0).
Balance : Adjust the left and right speaker output balance.
♦L6 to R6; Initial 0
Press [ 5/∞/2/3 ] or drag [
• To clear the adjustment, press [Center].
Equalizer
LoudnessYou can activate/deactivate the loudness function.
Audio
X’over
Volume Offset
Subwoofer
Speaker Select
Change the sound mode or adjust and store the equalization
for each source. (☞ page 43)
♦ Natural/Rock/Pops/Easy/Top40/Jazz/User
♦ ON
♦ OFF
Adjust the crossover frequency. (☞ page 44)
Adjust and store the auto-adjustment volume level for each
source. (For discs, the adjustment is stored for each of the
following categories: DVD/DVD-VR/VCD, CD, and DivX/
MPEG1/MPEG2/MP3/WMA/WAV/AAC.) The volume level will
automatically increase or decrease when you change the
source.
♦ –15 to +6; Initial 0
♦ ON
♦ OFF
Select the size of the connected speaker.
♦Standard/Narrow/Middle/Wide
: Boost low and high frequencies to
produce a well-balanced sound at a low
volume level. The LOUD indicator lights up.
: Cancels.
: Activates the subwoofer.
: Cancels.
] to adjust.
50 English
Page 51
Menu itemSelectable setting/itemInitial: Underlined
Dimmer
♦Auto
: Dims the screen and button illumination
when you turn on the headlights.
• The ILLUMI lead connection is required.
(☞ page 81 )
♦ ON
♦ OFF
♦ NAV
: Activates dimmer.
: Cancels.
: Activates or deactivates dimmer
according to the day/night display
setting of the connected navigation unit.
User Customize
Change the display design (background and panel color). (☞
page 45)
OSD Clock
♦ON
: Displays the clock while a video source is
played back.
: Cancels.
: Repeats scrolling.
: Scrolls the displayed information once.
: Cancels.
Display
Scroll
♦ OFF
♦ ON
♦ Once
♦ OFF
• Pressing [<] scrolls the text regardless of the setting.
Menu Customize
Change the items to display on the <Top Menu> screen. (☞
page 15)
Screen AdjustAdjust the brightness and blackness of the screen.
Select the dimmer mode (<DIM ON> or <DIM OFF>) for
adjustment, then change the following settings:
♦Bright
: Adjusts brightness (–15 to +15; Initial 0
for <DIMON>/+15 for <DIMOFF>).
: Adjusts blackness (–15 to +15; Initial 0).
Video Output *
♦Black
Select the color system of the external monitor.
♦NTSC/PAL
Angle
Adjust the panel angle. (☞ page 11)
Only for DDX790/
DDX770/DDX7070BT
*
“Please power off” appears when the setting is changed. Turn off the power, then turn on to enable the
change.
English 51
Page 52
Menu itemSelectable setting/itemInitial: Underlined
AV Input
You can determine the use of the iPod/AV-IN2 input terminal.
♦AV-IN2
: Select to play an AV component connected
to the iPod/AV-IN2 input terminal.
♦ iPod
: Select when connecting the iPod/iPhone
using the USB Audio and Video cable for
iPod/iPhone. (☞ page 82)
R-CAM Interrupt
♦ON
: Displays the picture from the rear view
camera when you shift the gear to the
reverse (R) position.
: Select this when no camera is connected.
: Select this when a SiriusXM Connect
Vehicle Tuner is connected.
: Enables control of the unit via ADS
External BUS*
Only for DDX370
Input
♦ OFF
♦ SXi
♦ OEM
adapter. Select this when an ADS adapter
is connected. To control sources via ADS
adapter, select [OEM Features] on <Top Menu>. (☞ page 14)
Navigation
Change the navigation settings. (☞ page 42)
Only for DDX7070BT/
DDX4070BT/DDX3070
NAV Mute
Only for DDX790/
Attenuate the sound coming out of speakers other than the
front speakers during navigation guidance.
DDX770/DDX470/
DDX370
Language *Select the text language used for on-screen information.
• For external monitors, only English/Spanish/French/German/
Italian/Dutch/Russian/Portuguese are available. If another
System
language has been selected, the text language for external
monitors will be set to English.
♦ GUI
Language
: Select a language (<English> or <Local>:
the language selected above) used for
displaying operation buttons and menu
items.
*
“Please power off” appears when the setting is changed. Turn off the power, then turn on to enable the
change.
52 English
Page 53
Menu itemSelectable setting/itemInitial: Underlined
Clock
Beep
Remote Sensor
Adjust the clock time. (☞ page 10)
♦ ON
♦ OFF
♦ ON
♦ OFF
: Activates the key-touch tone.
: Cancels.
: Activates the remote sensor.
: Cancels.
SETUP MemoryYou can memorize, recall, clear, or lock the settings you have
made. (☞ page 54)
Bluetooth Setup
Only for DDX790/
Configures settings for using a Bluetooth device, such as
connection and other general operations. (☞ page 58)
DDX770/DDX7070BT/
DDX470/DDX4070BT
OEM Bluetooth
Setup
Only for DDX370
OEM Setup
Only for DDX370
TEL Key Long Press
Only for DDX470/
System
DDX4070BT
Configures settings for using a Bluetooth device, connected via
ADS adapter. Press [Enter] to display the <OEM Handsfree
Setup> screen.
Shows the information/changes the settings for using the ADS
adapter.
Assigns the function of the TEL button when held.
♦ V-OFF
♦ VOICE
♦ R-CAM
: Turns off the screen. (☞ page 12)
: Activates voice dialing. (☞ page 60)
: Displays the picture from the rear view
camera. (☞ page 49)
AUD Key Long Press
Only for DDX370/
DDX3070
Assigns the function of the AUD button when held.
♦ V-OFF
♦ R-CAM
: Turns off the screen. (☞ page 12)
: Displays the picture from the rear view
camera. (☞ page 49)
DivX(R) VOD
Only for DDX7070BT/
DDX4070BT/DDX3070
This unit has its own Registration Code. Once you have played
back a file with the Registration Code recorded, this unit’s
Registration Code is overwritten for copyright protection.
• Press [Enter] to display the information.
• To return to the previous screen, press [OK].
SI
Activate or deactivate the security function. (☞ page 7)
Serial NumberDisplays the serial number.
Touch Panel Adjust
Adjust the touch position of the buttons on screen. (☞ page 54)
System InformationDisplays the version information on the software. You can
update the software. (☞ page 6)
English 53
Page 54
Memorizing/recalling t he
settings
You can memorize the settings changed
in the <Setup> menu and recall the
memorized settings anytime.
• The memorized settings are kept even
when the unit is reset.
1 On <Setup>:
2
• To cancel, press [No].
3 Select an operation.
[Recall]: Recalls the memorized settings.
[Memory]: Memorizes the current
settings.
[Clear]: Clears the currently memorized
settings.
• To cancel, press [Cancel].
Locking the settings
You can lock the settings to prevent them
from being changed.
•
is shown beside the settings that can
be locked.
1 On <Setup>:
2
To unlock the setting, press [Unlock].
Adjusting the touch position
You can adjust the touch position on the
touch panel if the position touched and the
operation performed do not match.
1 On <Setup>:
2 Touch the center of the marks
at the lower left and at the
upper right as instructed.
Confirmation message appears. Press
[Yes ].
54 English
• To reset the touch position, press
[Reset].
• To cancel the current operation, press
[Cancel].
Page 55
BLUETOOTH OPERATIONS
(Only for DDX790/DDX770/DDX7070BT/DDX470/DDX4070BT )
Information for using Bluetooth® devices
• While driving, do not perform complicated operations such as dialing the numbers, using
phonebook, etc. When you perform these operations, stop your car in a safe place.
• Some Bluetooth devices may not be connected to this unit depending on the Bluetooth
version of the device.
• This unit may not work for some Bluetooth devices.
• Connecting condition may vary depending on circumstances around you.
• When the unit is turned off, the device is disconnected.
Bluetooth o perations
Preparation:
Bluetooth adapter KS-UBT1 has been
Bluetooth is a short-range wireless radio
communication technology for the mobile
device such as mobile phones, portable PCs,
and other devices. The Bluetooth devices
can be connected without cables and
communicate with each other.
attached. Connect the microphone
(supplied) beforehand. ( ☞ pages 81 and 85 )
DDX790/DDX770/DDX7070BT
Bluetooth adapter (KS-UBT1)
DDX470/DDX4070BT
Bluetooth adapter (KS-UBT1)
English 55
Page 56
Connecting Bluetooth devices
Registering a new Bluetooth
device
When you connect a Bluetooth device to the
unit for the first time, make pairing between
the unit and the device for registration.
Pairing allows Bluetooth devices to
communicate each other.
• The pairing method differs depending on
the Bluetooth version of the device.
– For the device with Bluetooth 2.1: You
can pair the device and the unit using
SSP (Secure Simple Pairing) which only
requests confirmation.
– For the device with Bluetooth 2.0: You
need to enter a PIN code both on the
device and unit for pairing.
• Once the pairing is complete, it is
registered in the unit even if you reset the
unit. Up to 5 devices can be registered in
total.
• Only one device for Bluetooth phone and
one for Bluetooth audio can be connected
at a time.
• To use the Bluetooth function, you need to
turn on Bluetooth function of the device.
• To use the registered device, you need to
connect the device to the unit. (☞ page 57)
Pairing a Bluetooth device using SSP
(for Bluetooth 2.1)
When the Bluetooth device is compatible
with Bluetooth 2.1, pairing request is sent
from the available device. Confirm the
request both on the device and the unit.
Pairing a Bluetooth device using a PIN
code (for Bluetooth2.0)
• The maximum digit of the PIN code that
can be set is 16.
1 On <Top Menu>:
2 Display the <Bluetooth
Setup> screen.
3 Change the PIN code.
• If you skip changing the PIN code, go
to step 4.
56 English
PIN code (initial: 0000)
Rejects the request
Deletes last entry
Page 57
4 Operate the Bluetooth device
to complete pairing.
When pairing is complete, the device is
listed on <Paired Device List>. To use
the paired device, connect the device on
<Paired Device List> (☞ below).
Connecting a registered
Bluetooth device
1 Display the <Bluetooth
Setup> screen. (☞ page 56)
2
Deleting a registered
Bluetooth device
1 Display the <Bluetooth
Setup> screen. (☞ page 56)
2
3 Select a device to delete (1),
then delete the registration
(2).
Select the device you want to connect
(1), then select the usage of the device
([TEL (HFP)] for mobile phone, [Audio (A2DP)] for Bluetooth audio player, and
[PANDORA (SPP)] for Pandora*) (2).
• Selectable items depend on the device
you are operating.
• If you connect a device while another
device is connected, the device
previously connected is disconnected
and the connection for the recently
connected is established.
*
[PANDORA (SPP)] appears only for DDX790/
DDX770/DDX470 .
*
Confirmation message appears. Press
[Yes ].
*
[PANDORA (SPP)] appears only for DDX790/
DDX770/DDX470 .
*
English 57
Page 58
Setting up Bluetooth
You can perform general operations such as connection and initialization through <Bluetooth
Setup> on the <Setup> menu.
Displaying the <Bluetooth Setup> screen
1 On <Top Menu>:
3
2
<Bluetooth Setup> menu items
Menu itemsSelectable setting/itemInitial: Underlined
Paired Device
List
PIN CodeChanges the PIN code of the unit.
Device NameShows the device name to be shown on the Bluetooth device —
Device Address
Auto Connect
Bluetooth HF/
Audio
Auto Pairing
InitializeHold [Enter] to initialize all settings you have made for using Bluetooth
Press [Enter] to show the list of the registered devices. You can connect the
device or delete the registration (☞ page 57).
• Enter a new PIN code, then press [Enter].
“KENWOOD BT MM-7U2.”
Shows the device address of the unit.
♦ ON
♦ OFF
Select the speakers used for Bluetooth (both phone and audio player).
♦
Front Only
♦ All
♦ ON
♦ OFF
mobile phone and Bluetooth audio player.
: The connection is automatically established with the last
connected Bluetooth device when the unit is turned on.
: Cancels.
: From front speakers only.
: From all speakers.
: Establishes the pairing automatically with the connected
iOS device (such as iPhone) even if the Bluetooth function
is deactivated on the device. (Auto pairing may not work
for some devices depending on the iOS version.)
: Cancels.
58 English
Page 59
Using the Bluetooth mobile phone
Receiving a call
When a call comes in...
Call information
(if acquired)Rejects the call
• Phone operation is not available while
the picture from the rear view camera is
displayed. (☞ page 49)
When <Auto Response> is set to [On]
The unit answers the incoming call
automatically. (☞ page 64)
Ending a call
While talking...
Adjusting the volume of
microphone
While talking...
• This adjustment does not affect the volume
level of the other sources.
• To adjust the volume of calls/earpiece, use
VOLUME
DDX7070BT ) or VOL/ATT/AUD k nob ( for
DDX470/DDX4070BT ) on t he m onitor
panel.
/ (for DDX790/DDX770/
Switching between
handsfree mode and phone
mode
While talking...
Each time you press the button, the talking
method is switched (
mode /
: phone mode).
: handsfree
Notifying SMS reception
If the mobile phone is compatible with SMS
(Short Message Service), the unit tells you a
message has been received. (☞ page 64)
To read a received message, operate the
mobile phone after stopping the car in a
safe place.
• You cannot read, edit, or send a message
through the unit.
English 59
Page 60
Adjusting the echo cancel
level
While talking...
Making a call
1 On <Top Menu>:
2 Select a method to make a
call.
Phonebook/Call lists (
Direct number entry (☞the right column)
☞ page 61)
Direct number entry
Deletes last entry
Hold: Adds “+”
Presets the entered phone number on the
preset list (
• You can enter up to 32 numbers.
☞ page 62)
Voice d ialing
• Available only when the connected mobile
phone has the voice recognition system.
Or
DDX790/DDX770/
DDX7070BT
Speak the name you want to call.
DDX470/
DDX4070BT*
(Hold)
(Hold)
Voice dialing (
60 English
Preset list (For presetting,
☞ page 62)
☞ the right column)
To cancel, press [Cancel].
* This operation works only when <TEL Key Long
Press> is set to <VOICE>. (
☞ p age 5 3 )
Page 61
Using the phonebook/call lists
1
2 Select the initial.
• If the initial is not a letter or number,
press [Others].
Outgoing
IncomingFrom received call list.
MissedFrom missed call list.
Phonebook From phonebook.
From dialled call list.
• For copying the
phonebook, ☞ page
62.
2
To use the A-Z search on the phonebook
When <Phonebook> is selected, you can
search by initial.
1
3 Select a phone number from
the list.
To display the details of an entry
When <Phonebook> is selected...
1 Display the details of the
desired entry.
2 Select a phone number to call.
English 61
Page 62
Presetting the phone
numbers
You can preset up to 6 phone numbers.
1 On <Top Menu>:
Copying the phonebook
You can copy the phonebook memory of
a mobile phone into the unit (up to 400
entries).
1 On <Top Menu>:
2 Select an item from
phonebook/call lists.
3 Select a phone number.
(Hold)
4 Select a preset number to
store into.
• You can also preset the phone number
entered on <Direct Number> screen by
pressing [Preset]. (☞ page 60)
To delete the preset phone numbers,
initialize the settings from <Initialize> in
<Bluetooth Setup>. (☞ page 58)
2
3
PIN code (initial: 0000)
Numbers of the phonebook entries copied
4 Operate the target mobile
phone.
• Refer to the instruction manual
supplied with your mobile phone.
• To cancel the transfer, press [Finish].
5 Finish the procedure.
62 English
The phonebook memory is copied from
the mobile phone.
Page 63
Deleting the phone number
entries in the unit
1 Display the phonebook/call
list you want to delete. (☞ page
61)
2
• You cannot delete data when [Phone]
is selected.
3 Select the item you want to
delete.
About mobile phones compatible
with Phone Book Access Profile
(PBAP)
If your mobile phone supports PBAP, you
can display the phonebook and call lists
on the touch panel screen when the
mobile phone is connected.
• Phonebook: up to 5 000 entries
• Dialed calls, received calls, and missed
calls: up to 50 entries each
To display the phonebook/call lists of
the mobile phone or the unit
Connected mobile phone
Unit
Deletes all the numbers/names in the
selected item
A confirmation message appears. Press
[Yes ].
English 63
Page 64
Settings for Bluetooth mobile phone
1 On <Top Menu>:
3
2
Menu itemsSelectable setting/itemInitial: Underlined
Phone
Device
Auto
Response
SMS Notify
Ring Mode
Ring Tone
Change
Shows the connected phone device name.
♦ ON
♦ OFF
♦ ON
♦ OFF
♦ System
♦ Phone
When <Ring Mode> is set to <System>, press [Enter], then select the ring
tone for received calls and SMS from <Tone1>, <Tone2>, <Tone3>.
♦ Call Tone
♦ Message
Tone
: The unit answers the incoming calls automatically in 5
seconds.
: The unit does not answer the calls automatically. Answer
the calls manually.
: The unit informs you of the arrival of a message by ringing
and displaying “Receiving Message.”
: The unit does not inform you of the arrival of a message.
: The ring tone set on the unit is used.
: The ring tone set on the mobile phone is used. ( This
function may not work depending on the mobile phone.)
: Selects the ring tone for phone calls.
: Selects the ring tone for SMS.
64 English
Page 65
Using the Bluetooth audio player
• To register a new device, ☞ page 56.
• To connect/disconnect a device, ☞ page 57.
Playback status * (3: play / 8: pause)
Playing time *
Tag data (current track title/
artist name/album title) *
• Pressing [<] scrolls the text if
not all of the text is shown.
• The operation buttons, indications and information displayed on the screen differ
depending on the connected device.
[3]Starts playback.
[8]Pauses.
[4][¢]• Selects a track. (Press)
[MENU]Displays the <Top Menu> screen.
Available only for the devices compatible with AVRCP 1.3.
*
• Reverse/forward search* (Hold)
English 65
Page 66
DVD
t
TV
t
AUD
t
USING THE REMOTE CONTROLLER
Overview
DDX7070BT/DDX4070BT/DDX3070 :
This unit can be operated using the Remote Controller (RC-DV340) supplied with this unit.
DDX790/DDX770/DDX470/DDX370
Optional Remote Controller KNA-RCDV331 is designed for controlling this unit. Refer to the
instruction manual that comes with the remote controller.
:
CAUTION
• Put the Remote Controller in a place where
it will not move during braking or other
operations. A dangerous situation could
result, if the Remote Controller falls down
and gets wedged under the pedals while
driving.
• Do not leave the battery near fire or
under direct sunlight. A fire, explosion or
excessive heat generation may result.
• Do not recharge, short, break up or heat
the battery or place it in an open fire. Such
actions may cause the battery to leak fluid.
If spilled fluid comes in contact with your
eyes or on clothing, immediately rinse with
water and consult a physician.
• Place the battery out of reach of children. In
the unlikely event that a child swallows the
battery, immediately consult a physician.
Battery installation
Use two “AAA”/”R03”-size batteries.
Insert the batteries with the + and – poles
aligned properly, following the illustration
inside the case.
• If the Remote Controller operates only
over shorter distances or does not operate
at all, it is possible that the batteries are
depleted. In such instances, replace the
both batteries with new ones.
Remote Controller mode switch
The functions operated from the remote
controller differ depending on the position of
the mode switch.
AUD mode: Switch to this mode when
controlling a selected source or tuner source,
etc.
DVD mode: Switch to this mode when
playing DVDs or CDs etc. with the player
integrated in this unit.
TV mode: Not used.
• The position of the remote control mode
switch is indicated in the title of each
mode, e.g., “(AUD mode)”.
• When controlling a player that is not
integrated in the unit, select “AUD” mode.
66 English
Page 67
Operations from the remote controller
Common operations (AUD mode)
Source switching
Switches to the source to be played.
Hangs up the incoming/current call.
Volume control
Adjusts the volume.
Volume attenuating
Press the key once to lower the volume. Press
again to restore the previous volume.
NAV/V.SEL
Switches to the navigation screen.
Cursor key
Moves the cursor when displaying menu.
ENTER
Enters options.
Hands-free communication
When a call comes in, it answers the call.
Function
Switches the control screen.
MODE
Switches the aspect ratio.
Aspect ratio changes each time you press
this key.
OPEN
(Only f or DDX790/DDX770/DDX7070BT )
Adjusts the panel angle.
The panel angle changes each time you press
this key.
English 67
Page 68
DVD/VCD (DVD mode)
Track search and file search
Selects the track or file to be played.
Play/Pause
Pauses the track.
Press again to resume playing.
Stop
Memorizes the last point where the disc
stopped.
Direct search
Pressing this key switches the features that
can be searched directly.
DVD-VIDEO
Chapter number
Title number
Cancel
VCD 1.X, VCD 2.X (PBC OFF)
Track number
Cancel
VCD 2.X (PBC ON)
Track number
Cancel
Once you have switched to the direct search
feature, specify the search number from the
numeric keypad, and then press [ENTER] key.
Numeric keypad
• Specify the number to search in direct
search.
• Press
1
to fast forward/backward.
2
ABC
Switches the fast forward/backward speed
each time you press this key.
• Press
1
to slow forward/backward
2
ABC
during pause.
DVD Top Menu
Returns to the DVD top menu.
DVD Menu
Displays the DVD menu.
DVD-VR
Chapter number
Program/Playlist
Cancel
68 English
Page 69
SUBTITLE
Switches the subtitle language.
Track search and file search
Selects the track or file to be played.
ZOOM
Switches the zoom ratio each time you press
this key.
Picture Angle
Switches the picture angle each time you
press this key.
AUDIO
Switches the voice language each time you
press this key.
Music Disc/Audio file/Video file/
Picture file (AUD mode)
Folder search
Selects the folder to be played.
Play/Pause
Pauses the track.
Press again to resume playing.
Direct search
Pressing this key switches the features that
can be searched directly.
Music Disc
Track number
Cancel
Audio files in DVD/CD disc
Folder number
File number
Cancel
Once you have switched to the direct search
feature, specify the search number from the
numeric keypad, and then press [ENTER] key.
Numeric keypad
• Specify the number to search in direct
search.
English 69
Page 70
Radio/SiriusXM (AUD mode)
Band switching
Switches to bands received by the unit.
Station selection
Switches to broadcast stations received by
the unit.
• To use preset tuning, press the number of
a programmed broadcast station. (
)
6
MNO
–
1
• Press the direct tuning key first, then
specify the frequency of the station to
receive.
iPod (AUD mode)
Music/Video search
Selects the music/video to be played.
Seek mode switching
Switches the Seek mode (AUTO1, AUTO2,
MANU).
Direct tuning
After pressing this key, use the keypad to
specify the broadcast station you wish to
receive.
Example: 92.1MHz (FM)
1
2
ABC
9
WXYZ
or
Example: 810kHz (AM)
TUV
1
or
0
8
Numeric keypad
Play/Pause
Pauses the music/video.
Press again to resume playing.
USB (AUD mode)
Folder search
Selects the folder to be played.
File search
Selects the file to be played.
Play/Pause
Pauses the file.
Press again to resume playing.
70 English
Page 71
REFERENCE
Maintenance
Caution on cleaning the unit
Do not use
any solvent
(for example,
thinner, benzine,
etc.), detergent,
or insecticide. This may damage the monitor
or the unit.
Recommended cleaning method:
Gently wipe the panel with a soft, dry cloth.
Moisture condensation
Moisture may condense on the lens inside
the unit in the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the unit may malfunction.
In this case, eject the disc and leave the unit
turned on for a few hours until the moisture
evaporates.
How to handle discs
When removing a disc
from its case, press
down the center holder
of the case and lift the
disc out, holding it by the
edges.
• Always hold the disc by the edges. Do not
touch its recording surface.
When storing a disc in its case, gently
insert the disc around the center holder (with
the printed surface facing up).
• Make sure to store discs in their cases after
use.
Center holder
To keep discs clean
A dirty disc may not play correctly.
If a disc does become dirty, wipe
it with a soft cloth in a straight line
from center to edge.
• Do not use any solvents (for
example, conventional record cleaner,
spray, thinner, benzine, etc.) to clean discs.
To play new discs
New discs may have some
rough spots around the inner
and outer edges. If such a disc
is used, this unit may reject the
disc.
To remove these rough spots, rub the
edges with a pencil or ball-point pen, etc.
Do not use the following discs:
3 inch discWarped disc
Sticker and sticker
residueStick-on label
Unusual shape
C-thru Disc (semi-
transparent disc)
Transparent or semitransparent parts on
its recording area
English 71
Page 72
More about this unit
File playback
Playing DivX files
(Only for DDX7070BT/DDX4070BT/DDX3070)
• This unit can play back DivX files with the
extension code <.divx>, <.div>, or <.avi>
(regardless of the letter case—upper/
lower).
• Audio stream should conform to MP3 or
Dolby Digital.
• The file encoded in the interlaced scanning
mode may not be played back correctly.
Playing MPEG1/MPEG2 files
• This unit can play back MPEG1/MPEG2
files with the extension code <.mpg>,
<.mpeg>, or <.mod>.
• The stream format should conform to
MPEG system/program stream.
The file format should be MP@ML (Main
Profile at Main Level)/SP@ML (Simple Profile
at Main Level)/MP@LL (Main Profile at Low
Level).
• Audio streams should conform to MPEG1
Audio Layer-2 or Dolby Digital.
Playing JPEG files
• This unit can play back JPEG files with the
extension code <.jpg> or <.jpeg>.
• This unit can play back JPEG files that are at
32 x 32 to 8 192 x 7 680 resolution.
It may take time to display the file
depending on its resolution.
• This unit can play back baseline JPEG files.
Progressive JPEG files or lossless JPEG files
cannot be played.
We bear no responsibility for any loss
of data in an iPod/iPhone and USB mass
storage class device while using this
unit.
Playing MP3/WMA/WAV/AAC files
• This unit can play back files with the
extension code <.mp3>, <.wma>, <.wav>,
or <.m4a> (regardless of the letter case—
upper/lower).
• This unit can play back the files meeting
the conditions below:
– Bit rate:
MP3: 8 kbps – 320 kbps
WMA: 5 kbps – 320 kbps
AAC: 16 kbps – 320 kbps
– Sampling frequency:
8 kHz – 48 kHz (for MP3/WMA)
44.1 kHz (for WAV)
32 kHz – 48 kHz (for AAC)
• This unit can show ID3 Tag Version
1.0/1.1/2.2/2.3/2.4 (for MP3).
• This unit can also show WAV/WMA/AAC
Tag.
• This unit can play back files recorded in VBR
(variable bit rate).
• Files recorded in VBR have a discrepancy in
elapsed time indication.
• This unit cannot play back the following
files:
– MP3 files encoded with MP3i and MP3
PRO format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded with lossless,
professional, and voice format.
– WMA files which are not based upon
Windows Media® Audio.
– WMA/AAC files copy-protected with
DRM.
– AAC files encoded by using any other
application than iTunes.
– AAC files copy-protected with FairPlay
(except those stored on an iPod).
– Files which have the data such as AIFF,
ATRAC3, etc.
72 English
Page 73
Sound signals emitted through the rear terminals
Through the analog terminals (Speaker out/Front Preout/Rear Preout)
2-channel signal is emitted. When playing multi-channel encoded disc, multi-channel signals
are downmixed.
What appears to be trouble is not always serious. Check the following points before calling a
service center.
• For operations with the external components, refer also to the instructions supplied with
the adapters used for the connections (as well as the instructions supplied with the external
components).
If the following messages appear
General
MessageRemedy/Cause
“No Signal”• Start the playback on the external component connected to AV-IN1
• “Miswiring DC
Offset Error”
• “Warning DC
Offset Error”
“Parking off”
“Authorization Error” Check whether the connected iPod/iPhone is compatible with this
“USB Device Error”• The USB power voltage is abnormal.
“Panel Mecha Error” The panel does not work properly. Reset the unit.
“No Navigation”No navigation unit is connected.
Bluetooth (Only for DDX790/DDX770/DDX7070BT/DDX470/DDX4070BT )
MessageRemedy/Cause
“No BT Dongle”The Bluetooth adapter (KS-UBT1) is removed.
“Connection Error”The device is registered but the connection has failed. Connect the
“Please Wait...”The unit is preparing to use the Bluetooth function. If the message
“No Voice Device”
“No Data”No phonebook data is contained in the connected Bluetooth phone.
“Initialize Error”The unit has failed to initialize the Bluetooth module. Try the operation
“Dial Error”Dialing has failed. Try the operation again.
“Hung Up Error”The call has not ended yet. Park your car, and use the connected
“Pick Up Error”The unit has failed to receive a call.
or iPod/AV-IN2 input terminal.
• Check the cords and connections.
• Signal input is too weak.
A speaker cord has shorted or it has come in to contact with the car
chassis. Wire or insulate the speaker cord as appropriate, then reset the
unit (☞ pages 3 and 81 ).
No playback picture is shown when the parking brake is not engaged.
unit. (☞ page 25)
• Turn off and turn on the unit.
• Connect another USB device.
registered device. ( ☞ page 57)
does not disappear, turn off and turn on the unit, then connect the
device again (or reset the unit).
The connected mobile phone does not have the voice recognition system.
again.
mobile phone to end the call.
74 English
Page 75
Pandora (Only for DDX790/DDX770/DDX470/DDX370)
MessageRemedy/Cause
“Check Device”• Pandora application on your iPhone/iPod touch/smartphone is not
“Pandora upgrade
required”
“Cannot Skip”No more songs can be skipped.
“Rating Failed”Thumb-up/down is prohibited.
“No Station”No station is available.
“No Active Station”No station is being played.
“Cannot create a
station”
“Failed to save your
bookmark”
started up.
• Pandora application is not installed in the connected device.
• Error occurs on the Pandora application.
• You have not been signed in the Pandora.
The version of the Pandora application on your iPhone/iPod touch/
smartphone is not the latest. Update the version of your Pandora
application.
The registration of the stations to the Station List is full.
The unit has failed to bookmark. Try the operation again.
SiriusXM (Only for DDX790/DDX770/DDX470/DDX370)
MessageRemedy/Cause
“Check Tuner”The SiriusXM Connect Vehicle Tuner is disconnected or the unit is
“Subscription
Updated – Press Enter
to Continue”
“Chan Unavailable”The selected channel is not available.
“Ch UnSubscribed”The selected channel has not been subscribed yet.
“Channel Locked”The selected channel has been locked by parental controls, or a
“Incorrect Lock Code” The selected channel is a mature or parental lock channel, and
“Check Antenna”The antenna may have a problem. Check the antenna.
“No Signal”No satellite or terrestrial signal can be found. This message appears
having trouble communicating with the Tuner. Connect the Tuner or
check the Tuner connection to the back of the unit.
Your subscription status has been updated.
mature channel has been selected. Enter the unlock code when
required.
locked by parental lock or user lock code. Enter the correct lock code.
when the channel selection cannot be complete even in a given
time.
English 75
Page 76
If there seems to be a problem
SymptomRemedy/Cause
No sound comes out of the
speakers.
No picture is displayed on the
screen.
General
The unit does not work at all.
The remote controller* does not
work.
AME automatic presetting does
not work.
Static noise while listening to
TUNER
the radio.
• Recordable/Rewritable discs
cannot be played back.
• Tracks on the Recordable/
Rewritable discs cannot be
skipped.
Playback does not start.The format of files is not supported by the unit.
Disc in general
No picture appears on the
external monitor.
Disc cannot be played back.• Record the tracks using a compliant application
• Adjust the volume to the optimum level.
• Check the cords and connections.
Turn on the screen. (☞ page 12)
Reset the unit. (☞ page 3)
Replace the battery.
Store stations manually. (☞ page 29 )
Connect the antenna firmly.
• Insert a finalized disc.
• Finalize the discs with the component which you
used for recording.
• Connect the video cord correctly.
• Select the correct input on the external monitor.
on the appropriate discs. (☞ page 17)
• Add appropriate extension codes to the file
names.
Tracks are not played back as
you have intended them to play.
DivX/MPEG1/MPEG2/
JPEG/MP3/WMA/WAV/AAC
No picture appears on the
screen.
AV-IN2
AV-IN1/
* For DDX790/DDX770/DDX470/DDX370 , purchase KNA-RCDV331 separately.
76 English
Playback order may differ from the one played back
using other players.
• Turn on the video component if it is not on.
• Connect the video component correctly.
• When “
AV-IN2
Input> to [AV-IN].
” is selected as the source, set <AV
Page 77
SymptomRemedy/Cause
No sound comes out of the
speakers.
• Disconnect the iPod/iPhone, then connect it
again.
• Select another source and then reselect “iPod”.
The iPod/iPhone does not turn
on or does not work.
• Check the connecting cable and its connection.
• Update the firmware version.
• Charge the battery.
• Check whether the iPod/iPhone control mode is
correctly selected. (☞ page 27)
• Reset the iPod/iPhone.
Sound is distorted.Deactivate the equalizer either on this unit or the
iPod/iPhone.
A lot of noise is generated.Turn off (uncheck) the “VoiceOver” feature of the
iPod/iPhone
No operations are available
when playing back a track
iPod. For details, visit <http://www.apple.com>.
Operate the unit after the Artwork is loaded. (☞
page 25)
containing Artwork.
Sound does not synchronize
Select <iPod> for <AV Input>. (☞ page 52 )
with the video.
• Videos cannot be played.
• No sound of videos comes
out.
“Reading...” keeps flashing on the
• Connect USB Audio and Video cable KCA-iP202 .
Other cables cannot be used.
• Select <iPod> for <AV Input>. (☞ page 52 )
Turn off the power and on again.
screen.
USB
While playing a track, sound is
sometimes interrupted.
The tracks are not properly copied into the USB
device. Copy tracks again, and try again.
English 77
Page 78
SymptomRemedy/Cause
Phone sound quality is poor.• Reduce the distance between the unit and the
The sound is interrupted or
skipped while using a Bluetooth
audio player.
The connected audio player
cannot be controlled.
Bluetooth device does not
detect the unit.
The unit does not make pairing
with the Bluetooth device.
Echo or noise occurs.Adjust the microphone unit position.
The unit does not respond when
Bluetooth (only for DDX790/DDX770/DDX7070BT/DDX470/DDX4070BT )
you try to copy the phonebook
to the unit.
Bluetooth mobile phone.
• Move the car to place where you can get a better
signal reception.
• Reduce the distance between the unit and the
Bluetooth audio player.
• Disconnect the device connected for Bluetooth
phone.
• Turn off, then turn on the unit.
• (When the sound is not yet restored) connect the
player again.
Check whether the connected audio player
supports AVRCP (Audio Video Remote Control
Profile).
• Check whether the Bluetooth adapter (KS-UBT1)
is inserted correctly.
• Search from the Bluetooth device again.
• For the device compatible with Bluetooth2.1:
Register the device by using a PIN code.
(☞ page 56)
• For the device compatible with Bluetooth 2.0:
Enter the same PIN code for both the unit and
target device. If the PIN code of the device is not
indicated on its instructions, try “0000” or “1234.”
You may have tried to copy the same entries (as
stored) to the unit.
78 English
Page 79
Accessories/Installation P rocedure
Accessories
1
..........1
2
..........1 (2m: 6.5 ft)
3
..........6
4
..........6
5
..........1
1
6*
..........2
2
7*
..........2
2
8*
..........1
3
9*
..........1 (3m: 9.8 ft)
*1
DDX470/DDX4070BT/
DDX370/DDX3070
only.
*2 DDX790/DDX770/
DDX7070BT only.
3
DDX790/DDX770/
*
DDX7070BT/ DDX470/
DDX4070BT only.
Installation Procedure
1 To prevent a short circuit, remove the key
from the ignition and disconnect the ·
battery.
2 Make the proper input and output wire
connections for each unit.
3 Connect the speaker wires of the wiring
harness.
4 Connect the wiring harness wires in the
following order: ground, battery, ignition.
5 Connect the wiring harness connector to
the unit.
6 Install the unit in your car.
7 Reconnect the · battery.
8 Press the reset button.
9 Perform the Initial Setup.
WARNING
• If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may
start a fire. Always connect those wires to the
power source running through the fuse box.
• Do not cut out the fuse from the ignition wire
(red) and the battery wire (yellow). The power
supply must be connected to the wires via the
fuse.
¤
• Mounting and wiring this product requires
skills and experience. For best safety, leave the
mounting and wiring work to professionals.
• Make sure to ground the unit to a negative 12V
DC power supply.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
• Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
• If the power is not turned ON (“Miswiring
DC Offset Error”, “ Warning DC Offset Error” is
displayed), the speaker wire may have a shortcircuit or touched the chassis of the vehicle and
the protection function may have been activated.
Therefore, the speaker wire should be checked.
• If your car’s ignition does not have an ACC
position, connect the ignition wires to a power
source that can be turned on and off with the
ignition key. If you connect the ignition wire to
a power source with a constant voltage supply,
such as with battery wires, the battery may be
drained.
• Only for DDX790/DDX770/DDX7070BT: If the
console has a lid, make sure to install the unit so
that the faceplate will not hit the lid when closing
and opening.
English 79
Page 80
• If the fuse blows, first make sure the wires are not
touching to cause a short circuit, then replace the
old fuse with one with the same rating.
• Insulate unconnected wires with vinyl tape or
other similar material. To prevent a short circuit,
do not remove the caps on the ends of the
unconnected wires or the terminals.
• Connect the speaker wires correctly to the
terminals to which they correspond. The unit may
be damaged or fail to work if you share the ·
wires or ground them to any metal part in the car.
• When only two speakers are being connected
to the system, connect the connectors either to
both the front output terminals or to both the
rear output terminals (do not use one from each).
For example, if you connect the ª connector
of the left speaker to a front output terminal, do
not connect the · connector to a rear output
terminal.
• After the unit is installed, check whether the brake
lamps, blinkers, wipers, etc. on the car are working
properly.
• Mount the unit so that the mounting angle is 30°
or less.
• Do not press hard on the panel surface when
installing the unit to the vehicle. Otherwise scars,
damage, or failure may result.
• This unit has the cooling fan to decrease the
internal temperature. Do not mount the unit
in a place where the cooling fan of the unit is
blocked. Blocking these openings will prevent the
cooling of the internal temperature and result in
malfunction.
Cooling fan
DDX790/DDX770/DDX7070BT only
1 Before installation, remove the screws.
⁄ Do not use the removed screws for
installation.
2 Detach the sleeve using the two
extraction keys 7 then slide off the
mounting sleeve.
Accessory 7
¤ CAUTION
Install this unit in the console of your
vehicle.
Do not touch the metal part of this unit
during and shortly after the use of the
unit. Metal part such as the heat sink and
enclosure become hot.
80 English
DDX470/DDX4070BT only
• Install the Bluetooth adapter (KS-UBT1) besides
the place enclosed by the metal.
Bluetooth adapter (KS-UBT1)
Page 81
Connecting Wires t o Terminals
Bluetooth Microphone (Accessory
9) DDX790/DDX770/DDX7070BT/
DDX470/DDX4070BT only
Antenna Cord
FM/AM antenna input
Accessory 1
FUSE ( 10A )
White ª / White/black · : To front speaker (left)
Gray ª / Gray/black · : To front speaker (right)
Green ª / Green/black · : To rear speaker (left)
Purple ª / Purple/black · : To rear speaker (right)
If no connections are made, do not let the cable come out from the tab.
Purple/White
(Reverse sensor wire)
Light Green
(Parking sensor wire)
For best safety, be sure to connect
the parking sensor.
⁄
Subwoofer Preout (monaural)
Connect to vehicle's reverse lamp
harness when using the optional rear
view camera.
Connect to the vehicle's parking
brake detection switch harness.
Extension cable (Accessory 2)
Blue
(Antenna control wire)
Blue/White
(Power control wire)
Brown
(Mute control wire)
Light blue/Yellow
(Steering remote control wire)
Orange/White
(Dimmer control wire)
Red (Ignition wire)
Yellow (Battery wire)
Black (Ground wire) · (To car chassis)
Depending on what antenna you are using, connect
either to the control terminal of the motor antenna, or to
the power terminal for the booster amplifier of the filmtype antenna. (Max. 300 mA, 12 V)
When using the optional power amplifier, connect to its
power control terminal.
To the terminal that is grounded when either the
telephone rings or during conversation. (To connect the
Kenwood navigation system, consult your navigation
manual.)
To use the steering wheel remote control feature,
you need an exclusive remote adapter (not supplied)
matching your car is required.
To car light control switch
ACC
Ignition key switch
Car fuse box
(Main fuse)
Battery
English 81
Page 82
Connecting a USB device/iPod/iPhone
For DDX790/DDX770/DDX7070BT
iPod (commercially available)
USB device
(commercially available)
CA-U1EX*
(Optional Accessory)
0.8 m (2.6 ft)
KCA-iP202
(Optional Accessory)
1.8 m (5.9 ft)
* Use CA-U1EX for extending the cable if necessary. (Max 500 mA, 5V )
• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed
to connect specifically to iPod, or iPhone, respectively, and has been certified by the
developer to meet Apple performance standards. Apple is not responsible for the operation
of this device or its compliance with safety and regulatory standards. Please note that the use
of this accessory with iPod or iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered
in the U.S. and other countries.
• iTunes is a trademark of Apple Inc.
• DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its
subsidiaries and are used under license.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi
Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for
more information and software tools to convert your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order
to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code,
locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more
information on how to complete your registration.
• This item incorporates copy protection technology that is protected by U.S. patents and
other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly
are prohibited.
• Pandora, the Pandora logo, and the Pandora trade dress are trademarks or registered
trademarks of Pandora Media, Inc., used with permission.
• Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights
reserved.
• Android is a trademark of Google Inc.
• BlackBerry®, RIM®, Research In Motion® and related trademarks, names and logos are the
property of Research In Motion Limited and are registered and/or used in the U.S. and
countries around the world. Used under license from Research In Motion Limited.
88 English
Page 89
KS-UBT1 (USB Bluetooth adapter)
Instruction Manual
CAUTION
Changes or modifications not approved by us
could void the user’s authority to operate the
equipment.
• This adapter has been designed exclusively
for use with Kenwood car receivers. Do not
use this adapter with any other car receiver.
• The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by
JVC KENWOOD Corporation is under
license. Other trademarks and trade names
are those of their respective owners.
Distributor name: JVC KENWOOD DO BRASIL COMERCIO
CNPJ of distributor: JVC KENWOOD DO BRASIL COMERCIO
Manufacturer: JVC KENWOOD Corporation
Model no.: KS-UBT1
Brand: JVC
DE ELETRONICOS LTDA
DE ELETRONICOS LTDA
Specifications
Bluetooth Version:
Power Class: Class2 Radio
Service Area: 10 m (10.9 yd)
USB Standards: USB V1.1 (Full Speed)
Power Consumption: 54.3 mA/5 V (max.)
Dimensions (L × W × H):
15 mm × 19 mm × 5.6 mm
(5/8 ” × 3/4 ” × 1/4 ”)
Keep the Bluetooth adapter inserted when
using the Bluetooth function.
When the adapter is removed, store it in a
safe place.
Bluetooth Ver. 2.1 +EDR
0168-12-5373
(01)07898929117502
“Este equipamento opera em caráter secundário, isto
é, não tem direito à proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e não
pode causar interferência a sistemas operando em
caráter primário.”
English 89
Page 90
FCC WARNING
This equipment may generate or use radio
frequency energy. Changes or modifications
to this equipment may cause harmful
interference unless the modifications are
expressly approved in the instruction manual.
The user could lose the authority to operate
this equipment if an unauthorized change or
modification is made.
FCC NOTE
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment may cause harmful interference
to radio communications, if it is not installed
and used in accordance with the instructions.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
IC (Industry Canada) Notice
This device complies with Industry Canada
licence-exempt RSS standard(s).
Operation is subject to the following two
conditions:
(1) This device may not cause interference,
and (2) this device must accept any
interference, including interference that may
cause undesired operation of the device.
The term “IC: ” before the certification/
registration number only signifies that the
Industry Canada technical specification were
met.
CAUTION
This equipment complies with FCC/IC
radiation exposure limits set forth for an
uncontrolled environment and meets the
FCC radio frequency (RF) Exposure Guidelines
in Supplement C to OET65 and RSS-102 of
the IC radio frequency (RF) Exposure rules.
This equipment has very low levels of RF
energy that it deemed to comply without
maximum permissive exposure evaluation
(MPE). But it is desirable that it should be
installed and operated keeping the radiator at
least 20cm or more away from person’s body
(excluding extremities: hands, wrists, feet and
ankles).
Under Industry Canada regulations, this
radio transmitter may only operate using
an antenna of a type and maximum (or
lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio
interference to other users, the antenna
type and its gain should be so chosen that
the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for
successful communication.
90 English
Page 91
Page 92
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.