Kenwood CPS87 Service Manual

©
2001-1 PRINTED IN JAPAN
B51-7730-00 (N) 3387
CD AUTO CHANGER
KDC-CX87/CPS87
SERVICE MANUAL
COMPACT DISC AUTO CHANGER KDC-CX87
NEW ANTI VIBRATION MECHANISM
DYNAMIC RESOLUTION INTENSIVE VECTOR ENHANCEMENT
DISC NAME PRESET
TEXT
10
DISC
COMPACT
DIGITAL AUDIO
CD-R/RW
COMPACT DISC AUTO
NEW ANTI VIBRATION MECHANISM
DYNAMIC RESOLUTION INTENSIVE VECTOR ENHANCEMENT
DISC NAME PRESET
TEXT
10
DISC
COMPACT
DIGITAL AUDIO
CD-R/RW
CHANGER KDC-CPS87
Illustration is KDC-CX87.
Illustration is KDC-CPS87.
BRACKET x 2 (J19-4712-23)
SCREW SET (N99-1645-15) : KDC-CX87, CPS87(E)
SCREW SET (N99-1628-15) : KDC-CPS87(M)
MOUNTING HARDWARE ASSY x 2 (J21-9588-04) : KDC-CPS87(M)
HOLDER ASSY (J19-5074-02)
BLIND PLATE (F19-1303-04)
TRAY (J99-0612-01)
ADHESIVE TAPE x 2 (J69-0506-04) : KDC-CPS87(M)
CORD WITH PLUG (E30-4291-05 or E30-4954-05)
The MECHANISM OPERATION is the same as model KDC-C710. Please refer to the service manual of model KDC-C710 (B51-7104-00).
Service jig Parts No.
For initial position setting W05-0635-00
When transporting these models, always attach CAUTION CARD and STEPPED SCREW (for transportation)
KDC-CX87/CPS87
2

BLOCK DIAGRAM

SW5V
XOFF
LIM SW
L.P.S.
EJ SW
ARM SW
12.5MHz
X2
SPINDLE/LO-EJ
SLED
LOE SW
TR COIL
FO COIL
BTL
EEPROM
&TEXT DECODER
APC
SA5V
Q1
S8V
SYSTEM u-COM
IC7
IC1
RF AMP&SARVO DSP
16.93MHz
X1
P-ON
Q10
Q15,16
Q20
BU. DET
IC8
7
13
4
5
8
2
IC5
MG SW
8V AVR
S8V
COMM SW
S-RAM
24
C
IC10
DAC DIGITAL FILTER
D.R.I.V.E.
4
L.P.F
IC3
X1
4.19MHz
AUX SW
I/F u-COM
IC2
RST
6
Q7
BU.
BU14V
CH MUTE
CH RST
REQC0
CHCON
DATAH0
DATA C0
REQH0
HCLK0
AUDIO OUT
BU14V
CH RST2
CH MUTE2
HCLK2 REQC2
DATA C2
REQH2
CHCONO2
DATAH2
6
AUDIO IN
AUX to AUX
CH2
H.U
5
RELAY K1,3
K2,4
RELAY
DET
to
to
5VREG
IC4
DA5V
S8V
3
3
3
3
S1
IC1
Q9,10
AVR
5V
+5V
S4
HOT
IC9
RST
7V/9V
5V
Q21,22
M5V1 M5V2
SW5V
S3
S2
S1
+5V
SW5V
M
M
&DC MOTOR
DRIVER
ELEVATOR
M
AVR
SA5V
Q9
&D/A CONVERTER &SCF
AUDIO VREF
IC2
MUTE
0bit
Q6,7
MUTE
Q4,5,8
SD5V
FE
A
D
B
PD
M5V2
AVR
IC11
2
ASSY (X13)
(X32)
(X13)
(X92)
PICKUP
CN101
DRIVER
RESET
Q101,201
ACC
BATT
GND
DETECTION
ACC
(+5V)
AVR
u-COM
IC2
IC1
CN103
Q1,6
Q4,5
VDD
HOLD
P ON PLL
63
31
67
12-17 26 61
29,30,60
74,77
IC1
LCD DRIVER
LCD1
19-22,32,66
19-22,32,66
CN101
CN1
6-43
RL1
CN105
RADIO
To
CN104
ANT IN
Q310
MODE 1,2
CH-CONTROL
Q306,
RIPPLE FILTER
307
MIX
PILOT
STAGE
RF
IC301
MODULATOR
FM-St.
Q304,305 LEVEL CONTROL
AUDIO MUTE
Q309
ALC DETECTION
IC302
AMP
DRIVER
ALC
MPX
EMPHASIS
IC4
AVR(+5.6V)
MODE 1,2
Q308
CD-CH
13P
IC101
ISOLATION AMP. L.P.F.
2nd.
IC102
+V(AUDIO)
+V(RF STAGE)
SIGNAL (L/R)
CN102
KEY MATRIX
2,50-56
VDD
IC2
REMOTE SENSER
3
1
KDC-CX87/CPS87
3
IC1 UPD78058GCB82T System MI-COM. CH1/CH2/AUX control IC2 PST9137NR Reset IC When BU 5V voltage is less than 3.7V, IC outputs "Lo".
Q1 DTC124EUA
While CD-CH1's outputs are selected, Q1's base goes "Lo", and Q3 is
Relay drive turned off.
Q3 DTB123YK
(CH1/CH2 switching)
While CD-CH2's outputs are selected, Q1's base goes "Hi", and Q3 is turned on.
Q2 DTC124EUA
Relay drive
While CD-CH's outputs are selected, Q2's base goes "Lo", and Q4 is
(CH/AUX switching)
turned off.
Q4 DTB123YK
While AUX inputs are selected, Q2's base goes "Hi", and Q4 is turned on.
Q5 2SC4081 CH CON2 SW While CH CON2 mode is selcted, a base goes "Hi", and Q5 is turned on.
Q6 2SC4081 CH CON SW
While CH CON or CH CON2 mode is selcted, a base goes "Hi", and Q6 is turned on. While BACKUP is applied, a base goes "Hi", and Q7 is turned on.
Q7 DTC124EUA
BU DETECTION SW
When momentary power down has detected, a base goes "Lo", and Q7 is
turned off. Q8 DTC124EUA Reset SW When System Reset has activated, a base goes "Hi", and Q8 is turned on. Q9 2SB1202
BU 5V AVR
While BACKUP is applied, AVR outputs +5V.
Q10 2SC4081 Q9 and Q10 are inverted Darlington connection
CD PLAYER UNIT (X32-5160-00)
Ref.No.
Component Name
Application/Function
Operation/Condition/Compatibility
RF amplifier built in digital servo and data processor IC. Focusing, tracking,
sled and spindle servo processing. Detection of dropout, anti-shock, track
IC1 UPD63711AGC Servo IC
crossing and off-track conditions.
Automatic adjustment (focusing, tracking, gain, offset and balance)
operations. Digital signal processing (DSP, PLL, sub-codes, CD-TEXT
decode, CIRC error correction, audio data interpolaration) operations.
IC2 NJM4580MD VREF amp. Operational reference voltage for low pass filter IC3 NJM5532MD Low pass filter Differential amplifier IC4 KIA78L05F +5V AVR Analogue output circuit power supply for D/A converter
Focusing coil, tracking coil, spindle motor and sled motor driver.
VO1-VO4 and VOL outputs ON/OFF function
While MUTE1 goes "Hi", VO1 outputs are turned on. While MUTE2 goes "Hi", VO2-VO4 and VOL outputs are turned on.
VIN1 amplifier function (input selection and VREF selection)
IC5 LA6576 Motor driver 1. Input selection
While VIN SW terminal goes "Lo", IC pin 15, 16 and 17 inputs are selected. While VIN SW terminal goes "Hi", IC pin 15, 18 and 19 inputs are selected.
2. VREF selection While VIN SW terminal goes "Lo", internal VREF (2.5V typical) is selected. While VIN SW terminal goes "Hi", external VREF (IC pin 30 input) is selected.
SUB-CIRCUIT UNIT (X13-9930-00)

COMPONENT DESCRIPTION

Ref.No.
Component Name
Application/Function
Operation/Condition/Compatibility
KDC-CX87/CPS87
4
COMPONENTS DESCRIPTION
Ref.No.
Component Name
Application/Function
Operation/Condition/Compatibility
IC7 UPD784214GC091
Mechanism MI-COM.
Mechanism and servo control BR24C02F-W or CAT24WC02JI
IC8 or M24C02WMN6T EEPROM LPS data back-up memory
or S-24C02BFJA or 24LC02BT-ISN
IC9 S-80830ANNP Reset IC When BU 5V voltage is less than 3.0V, IC outputs "Lo". IC10 KKZ05F D.R.I.V.E. IC D.R.I.V.E. system IC IC11 LC3564BT-70 S RAM CD-TEXT data memory
Q1 MCH6101 APC Laser diode auto power control Q4 DTA124EK 0 bit mute (L CH.) When 0 bit mute is activated, an emitter goes "Hi", and Q4 outputs "Hi". Q5 DTA124EUA 0 bit mute (R CH.) When 0 bit mute is activated, an emitter goes "Hi", and Q5 outputs "Hi".
Q6 DTC343TK Mute SW (L CH.)
When 0 bit mute or A mute drive is activated, a base goes "Hi", and L channel audio signal is muted.
Q7 DTC343TK Mute SW (R CH.)
When 0 bit mute or A mute drive is activated, a base goes "Hi", and R channel audio signal is muted.
Q8 DTA124EK A mute drive
When audio mute of IC7 is activated, a base goes "Lo", and audio mute drive signal is outputted.
Q9 2SB1202 Servo 5V AVR Q9 is combined with IC5's pin 26 and 27 , and works as a driver of AVR.
Q10 2SB1295 P-ON 5V SW
While base goes "Lo", P-ON 5V is supplied to the microprocessor
peripheral circuits. Q11 DTC124EK Reset SW When System Reset has activated, a base goes "Hi", and Q11 is turned on. Q12 DTC124EUA XTALEN SW While D.R.I.V.E. IC is operating, a base goes "Lo", and Q12 is turned off.
Q13 DTC124EUA CH CON SW
While CH CON or CH-CON2 mode is selected, a base goes "Hi", and Q13
is turned on.
Q14 DTA143EUA CH MUTE SW
When MUTE REQUEST to H/U is outputted, a base goes "Lo", and Q14 is
turned on. Q16 2SC4081 SRV 8V AVR Q16 is combined with Q15 (X92-), and works as a pre-driver of AVR. Q17 DTA143EK
SRV 8V AVR SW
When Q18's base goes "Hi", Q17 is turned on, and SVR 8V AVR is Q18 DTC124EUA working.
Q19 DTC124EUA 7/9V SW
When a base goes "Hi", Q19 is turned on, and SVR 8V AVR is outputting +7V.
When a base goes "Lo", Q19 is turned off, and SVR 8V AVR is outputting +8.5V.
While BACKUP is applied, a base goes "Hi", and Q20 is turned on. Q20 DTC124EK
BU DETECTION SW
When momentary power down has detected, a base goes "Lo", and Q20 is
turned off. Q21 2SB1202
BU 5V AVR
While BACKUP is applied, AVR outputs +5V. Q22 2SC4081 Q21 and Q22 are inverted Darlington connection.
Q30 DTC114YUA Eccentric disc SW
When an eccentric disc is detected, Q30 is turned on, and a preceding
beam is made to be delayed.
Q31 DTC124EUA VIN SW
While spindle servo or disc loading/eject mode is selected, a base goes
"Hi", and Q31 is turned on.
KDC-CX87/CPS87
5

MICROCOMPUTER'S TERMINAL DESCRIPTION

Pin No. Pin Name I/O Description Processing Operation
1 - 3 O Not used(N.C.)
4 AVSS - A/D, D/A converter ground connection terminal 5 O Not used(N.C.) 6 REQH1 O Communication request output to CH1 "Lo" : Communication requested 7 AVREF1 I D/A converter reference voltage input 8 DATAC1 I Data input from CH1
9 DATAH1 O Data output to CH1 10 HCLK1 I/O Communication clock input/output with CH1 11 DATAH0 I Data input from H/U 12 DATAC0 O Data output to H/U 13 HCLK0 I/O Communication clock input/output with H/U 14 REQC0 O Communication request output to H/U "Lo" : Communication requested 15 REQH2 O Communication request output to CH2 "Lo" : Communication requested 16 DATAC2 I Data input from CH2 17 DATAH2 O Data output to CH2 18 HCLK2 I/O communication clock input/output with CH2 19 CHCON01 O Control output to CH1 "Hi" : CH1 operation mode 20 CHCON02 O Control output to CH2 "Hi" : CH2 operation mode 21 RELAY1 O Relay1 Control output "Hi" : AUX inputs, "Lo" : Changer outputs 22 RELAY2 O Relay2 Control output "Hi" : CH2 outputs, "Lo" : CH1 outputs
23-32 O Not used(N.C.)
33 VSS - Ground connection terminal Connected to GND lines.
34-59 O Not used(N.C.)
60 RESET I System reset "Lo" : System reset 61 REQC2 I Communication request input from CH2 "Lo" : Communication requested
62 BUDET I Momentary power down detection input
"Hi" : When momentary power down detected or BU OFF
"Lo" : BU ON 63 AUX SW I AUX SW input "Hi" : Auxiliary input mode 64 REQH0 I Communication request input form H/U "Lo" : Communication requested 65 REQC1 I Communication request input form CH1 "Lo" : Communication requested 66 CHCON1 I Changer control mode input from H/U "Lo" : CH1 mode 67 COMMSW I 5-line communication old/new switch input
"Hi" : New communication, "Lo" : Old communication 68 VDD - Positive power supply connection terminal Connected to BU 5V lines. 69 X2 - Main clock resonator connection terminal 2 70 X1 I Main clock resonator connection terminal 1 71 IC - IC Internal connection terminal Connected to GND lines. 72 O Not used(N.C.) 73 CHCON2 I Changer control mode input from H/U "Lo" : CH2 mode 74 AVDD -
A/D converter positive power supply connection terminal
Connected to BU 5V lines. 75 AVREF0 I A/D converter reference voltage input Connected to BU 5V lines. 76 O Not used(N.C.) 77 AUX TYPE O Not used(pull down to GND lines.)
78-80 O Not used(N.C.)
IC1 (SUB-CIRCUIT UNIT: X13-9930-00)
KDC-CX87/CPS87
6
MICROCOMPUTER'S TERMINAL DESCRIPTION
Pin No. Pin Name I/O Description Processing Operation
1 NOR/RW O CD-DA/CD-RW Switching Not used(N.C.) 2 TSTB O CD-TEXT parameter strobe 3 P-CON O P-CON output Not used(N.C.) 4 FOK I Focus OK input "Hi" : Focus OK 5 XTALEN O Servo IC oscillation stop control "Hi" : Oscillation stop 6 RST O Servo IC reset terminal "Lo" : Reset 7 SAO O Servo IC command/parameter setting terminal
"Hi" : Parameter setting, "Lo" : Address resister setting
8 SSTB O
Servo IC command/parameter setting strobe terminal
"Hi""Lo" : Serial data latch
9 VDD - Positive power supply connection terminal Connected to D 5V lines. 10 X2 - Main clock resonator connection terminal 2 11 X1 I Main clock resonator connection terminal 1 12 VSS - Ground connection terminal Connected to GND lines. 13 XT2 - Sub clock resonator connection terminal 2 Not used(N.C.) 14 XT1 I Sub clock resonator connection terminal 1 Not used(connected to GND lines.) 15 RESET I System reset input "Lo" : System reset 16 FOGUP I Vibration detect input "Hi" : Vibration detect 17 MGSW I Magazine switch input "Hi" : Magazine in 18 EJSW I Eject switch input "Hi" : Eject switch ON 19 COMMSW I 5-line communication old/new switch input
"Hi" : New communication, "Lo" : Old communication 20 PACK I Text data pack synchronous signal input "Hi""Lo" : The head of the pack data 21 CH-CON I Changer control input "Hi" : Standby mode, "Lo" : Operation mode
22 BUDET I Momentary power down detection input
"Hi" : When momentary power down detected or BU OFF
"Lo" : BU ON 23 AVDD -
A/D converter positive power supply connection terminal
Connected to D 5V lines. 24 AVREF0 I A/D converter reference voltage input Connected to PON 5V lines. 25 HOT I Rise in temperature detection input 26 LPS I LPS Mechanical deck position detection input 27 LOESW I Loading complete switch input "Lo" : Loading complete 28 LIMSW I Limit switch input "Lo" : Pickup most inner position 29 TOFF I Tracking OFF mode terminal Not used(pull down to GND lines.) 30 ADJSEL I Servo automatic adjustment ON/OFF terminal Not used(pull down to GND lines.) 31 TBANK I Tracking gain switching mode terminal Not used(pull down to GND lines.) 32 SIM2 I Destination input 2 Not used(pull down to GND lines.) 33 AVSS - A/D, D/A converter ground connection terminal Connected to GND lines. 34 LPSCO O
LPS A/D converter reference power control output
Not used(N.C.) 35 AMUTE O Audio mute output "Lo" : Audio mute ON 36 AVREF1 I D/A converter reference voltage input Connected to D 5V lines. 37 SDI I Servo IC communication serial data input 38 SDO O Servo IC communication serial data output 39 SCK O Servo IC communication serial clock output 40 DATAH I Data input from H/U 41 DATAC O Data output from the changer 42 HCLK I/O Communication clock input/output with H/U
IC7 (CD PLAYER UNIT : X32-5160-00)
KDC-CX87/CPS87
7
MICROCOMPUTER'S TERMINAL DESCRIPTION
Pin No. Pin Name I/O Description Processing Operation
43 RECQC O Communication request to H/U "Lo" : Communication requested
44 CHMUTE O Audio mute request to H/U "Lo" : Audio mute requested
45 TSI I Text data input from servo IC
46 TSO O Text data output to servo IC
47 TSCK O Text data clock to servo IC
48-55 A0-A7 O Address setting terminal for S RAM
56-63 D0-D7 I/O Data input/output terminal with S RAM
64-68 A8-A12 O Address setting terminal for S RAM
69-71 A13-A15 O Chip enable setting terminal for S RAM Not used(pull down to GND lines.)
72 VSS - Ground connection terminal Connected to GND lines.
73 A16 O Chip enable setting terminal for S RAM Not used(pull down to GND lines.)
74 A17 O Chip enable setting terminal for S RAM
75 RAMOK O Pickup check judging terminal for production Not used(N.C.)
76 ELVADJ I
Mechanism deck ascent/descent position terminal
Not used(pull up to D 5V lines.)
77 RD O Read-out to S RAM control output
78 WR O Write to S RAM control output
79 WAIT I
Waiting time insertion input when accessing S RAM
Not used(pull down to GND lines.)
80 ASTB O Chip selection to S RAM Not used(N.C.)
81 VDD - Positive power supply connection terminal Connected to D 5V lines.
82 PUSEL I Pickup type select terminal Not used(pull up to D 5V lines.)
83 REQH I Communication request from H/U "Lo" : Communication requested
84 SPLO+ O Spindle/Loading control terminal
85 SPLO- O Spindle/Loading control terminal
86 ELV+ O Mechanism deck ascent/descent terminal
87 ELV- O Mechanism deck ascent/descent terminal
88 SIM1 I Destination input 1
"Hi" : adapted for CD-TEXT
"Lo" : not adapted for CD-TEXT
89 SEARCH O Search mode output Not used(N.C.)
90 TEST1 I Test mode terminal 1 for test mode Not used(pull down to GND lines.)
91 TEST2 I Test mode terminal 2 for test mode Not used(pull down to GND lines.)
92 8/7V O Motor driver IC power voltage control output "Hi" : 7V, "Lo" : 8.5V
93 EEPWR I EEPROM write mode terminal for production Not used(pull down to GND lines.)
94 TEST/VPP I Flash ROM program mode terminal Not used(connected to GND lines.)
95 SRVSEL I
Servo active mode terminal (no mechanism movement)
Not used(pull down to GND lines.)
96 SLNSA I Sled non-sensitive area ON/OFF terminal Not used(pull down to GND lines.)
97 SDA I/O Data input/output with EEPROM
98 SCL O Clock output to EEPROM
99 PON O PON output "Lo" : AVR & LPS POWER ON
100 ARMSW I Arm switch input "Hi" : Arm switch ON
Loading...
+ 14 hidden pages