Kenwood CM470, CM480, CM477 User Manual

key

 water filter  water filter holder  removable water tank  lid  compartment for excess cord  hotplate (model CM470 series only)  anti drip activating device  program button  clock button  on/off button with indicator light  glass carafe and lid

(model CM470 series only)

 thermal carafe and lid

(model CM480 series only)

 measuring spoon  filter holder  permanent coffee filter (or use a

paper filter instead)

 lid opening lip  aroma control  cup storage area

to make coffee

1 Lift the lid. 2 Lift out the water tank from the

coffee maker.

3 Separate the water filter holder by

pulling the unit apart and place the water filter inside. Fit the unit back together.

4Turn the handle on the water filter

holder and align the arrow on the base with the letter for the current corresponding month eg F for February.

5 Lower the water filter holder into

the water tank and fit into position in the recess.

6 Fill the tank with the desired

amount of water. The water must be between the top and bottom cup marks. Do not fill above the MAX level. (Alternatively fill the water tank when fitted inside the coffee maker but take care not to cause spillage.)

● Use cold water. We recommend

using filtered water from a Kenwood Water Filter as it reduces limescale. Never use warm or fizzy water.

7 Replace the water tank back into

the coffee maker.

8Ensure the filter holder is in

position in the coffee maker.

9 Fit either the permanent filter

supplied or a paper filter into the filter holder. Add the coffee, use the spoon provided (approximately 1 level spoon per cup or to taste).

10 Close the lid and adjust the aroma

control as required. Turn the control to the left for stronger coffee and to the right for weaker coffee.

11 CM470 series

● Put the carafe on the hotplate.

CM480 series

To achieve the best performance, rinse the thermal carafe with hot water immediately before switching on the coffee maker.

● Screw the lid onto the thermal

carafe. For brewing, the lid should be fully closed with the tab on the lid in line with the carafe handle. Put the carafe on the base.

12 Plug into the power supply and

press the on/off button.

13 Press the on/off button twice to

start brewing immediately. The on/off button will glow and the coffee maker will start to operate. The back light of the display will come on and automatically switch off after 10 minutes. To stop the brewing process at any time, press the on/off button. The back light of the display will come on for one minute and then go off automatically.

14 Don’t remove the carafe until

brewing has finished.

safety

● Watch out for steam, never lift the

tank lid during the brewing cycle.

● CM470 series only: never

touch the hotplate.

● Always lift the lid using the lid

opening lip.

● Don’t touch hot parts including

the cup storage area.

● Keep children away from the

machine. And never let the cord hang down where a child could grab it. Push excess cord inside the back of the machine.

● Never use a damaged machine.

Get it checked or repaired: see ‘service and customer care’.

● Never put the machine in water or

let the cord or plug get wet - you could get an electric shock.

● Unplug:

●●

before filling with water

●●

before cleaning

●●

after use.

● Never leave the machine on

unattended.

● Don’t let the cord touch hot parts.

● Always make sure there is water in

the tank before switching on.

● This coffee maker is only suitable

for use with the type of carafe supplied.

●

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

●

Children should be supervised to ensure that they do not play with the appliance.

●

Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.

before plugging in

Make sure your electricity supply is the same as the one shown on the underside of your machine.

Important (UK) only

●

The wires in the cord are coloured as follows: Green and Yellow = Earth Blue = Neutral Brown = Live.

● The appliance must be protected

by a 13A approved (BS1362) fuse.

● WARNING: THIS APPLIANCE

MUST BE EARTHED.

Note:

● For non-rewireable plugs the fuse

cover MUST be refitted when replacing the fuse. If the fuse cover is lost then the plug must not be used until a replacement can be obtained. The correct fuse cover is identified by colour and a replacement may be obtained from your Kenwood Authorised Repairer (see Service).

● If a non-rewireable plug is cut off it

must be DESTROYED IMMEDIATELY. An electric shock hazard may arise if an unwanted non-rewireable plug is inadvertently inserted into a 13A socket outlet.

●

This machine complies with European Economic Community Directive 89/336/EEC.

before using for the first time

1Remove all packaging. 2 Wash the parts: see ‘care and

cleaning’.

3 Push excess cord inside the back

of the machine.

4 Run two lots of water through the

machine (without coffee) to clean it out. Fill the tank to the top cup mark when you do this. See ‘to make coffee’.































  

Kenwood Limited, New Lane, Havant, Hampshire PO9 2NH, UK

www.kenwoodworld.com

56087/3

CM470 series

CM480 series

CM470 series

● The hot plate will keep your coffee

hot, but the sooner you drink it, the better it will taste.

● Your coffee maker will keep the

coffee warm and then automatically switch off after 2 hours. To manually switch off earlier, press the on/off button.

CM480 series

● To pour coffee after brewing has

finished, unscrew the lid 180° so that the tab on the lid is in line with the pouring spout. Once the desired amount of coffee has been poured, screw the lid back on to best retain the coffee temperature.

● As soon as all the coffee has

brewed, switch off and unplug the machine.

● If you haven’t used the machine

for a while, run one lot of water through it (without coffee) to clean it out. Fill the water tank to the top cup mark when you do this.

● Never put the carafe in the

microwave.

to set the clock

1 Plug in the coffee maker, the

backlight will come on and the display will flash.

2 Select the correct time of day by

pressing the clock button once and the time will advance by 1 minute. Press and hold down the button and the time will advance in 15 minute intervals.

● If required, press the program

button once to change between the 12 and 24 hour clock.

3 To set the clock press the on/off

button or wait 1 minute for it to automatically set.

● To re-adjust the clock at any time,

press and hold the clock button for 5 seconds and adjust the clock as above.

Note – the backlight of the display will automatically turn off after 1 minute.

to program automatic brew

1Set the clock to the correct time

(see ‘to set the clock’).

2 Press the program button, the

clock symbol and the display will flash.

3 Press the clock button until the

desired brewing time is displayed (follow procedure in ‘to set the clock’).

4 Press the on/off button to confirm

the automatic time selected. (The display panel and the on/off indicator light will flash).

5 Press the program button to

return to the current time of day (the on/off button will continue to flash). The brewing cycle will begin once the set time is reached and the on/off button will stop flashing.

●

If you want to check the automatic time selected, press the program button.

●

To override the automatic brewing operation press the on/off button and the coffee maker will start immediately. Press the button again to switch off.

care & cleaning

●

Always switch off, unplug and allow to cool before cleaning.

●

Never put the machine in water or let the cord or plug get wet.

●

Don’t wash parts in the dishwasher.

water filter

●

Change and discard the water filter after 70 brewing operations or within a calender month whichever is sooner.

carafe, lid, permanent filter, filter holder, water filter holder

●

Wash, then dry.

body

●

Wipe with a damp cloth, then dry. Don’t use abrasives - they’ll scratch the plastic and metal surfaces.

descaling

With use, the display will indicate when the coffee maker requires descaling. A series of solid lines will gradually appear and when 4 appear in the display and flash , the coffee maker has completed 100 cycles or more and requires descaling (see ‘to descale’).

important

When descaling always remove the water filter and water filter holder first.

to descale

1 Buy a suitable descaler. 2 Descale the machine. 3 After descaling, run several lots of

water through the machine to clean it out. Fill the tank to the top

cup mark when you do this. 4 Wash the parts. 5 To reset the descale counter to

zero, press the clock and program

button at the same time for 2

seconds.

service and customer care

●

If the cord is damaged it must, for safety reasons, be replaced by Kenwood or an authorised Kenwood repairer.

If you need help with:

●

using your machine or

●

servicing, spare parts or repairs (in or out of guarantee)

 call Kenwood customer care on

023 92392333. Have your model number ready - it’s on

the underside of the coffee maker.

For spare parts including water filters call 0870 241 3653.

●

other countries

Contact the shop where you bought your machine.

guarantee

If your coffee maker goes wrong within one year from the date you bought it, we will repair it (or replace it if necessary) free of charge provided:

●

you have not misused, neglected or damaged it;

●

it has not been modified (unless by Kenwood);

●

it is not second-hand;

●

it has not been used commercially;

●

you have not fitted a plug incorrectly; and

●

you supply your receipt to show when you bought it.

This guarantee does not affect your statutory rights.