HEAD OFFICE: Kenwood Limited, 1-3 Kenwood Business Park, New Lane, Havant, Hampshire PO9 2NH
126672/1
BLP60
BLM60
BLP61
BLM61
햲
햳
햵
햶
햷
햸
햹
햺
햻
햽햾햿
BLP61/BLM61
햴
헀
햶
햷
햸
헁
헂
헃
헄
safety
G
Read these instructions carefully and retain
for future reference.
G
Remove all packaging and any labels.
G
Switch off and unplug:
GG
before fitting or removing parts;
GG
when not in use;
GG
before cleaning.
G
Never fit the blade unit to the power
unit without the blender goblet or mill
jar fitted.
G
Always unplug the appliance before putting
your hands or utensils in the goblet.
G
Always take care when handling the blade
assembly and avoid touching the cutting
edge of the blades when cleaning.
G
Only operate the blender with the lid in place.
G
Only use the goblet with the blade assembly
supplied.
G
Never let the power unit, cord or plug get
wet.
G
Never use a damaged appliance. Get it
checked or repaired: see ‘service and customer care’.
G
Never use an unauthorised attachment.
G
SCALD RISK: Hot ingredients should be allowed to cool to room temperature before
blending.
G
Never leave the appliance unattended when it
is operating.
G
When removing the blender or mill from the
power unit:
GG
wait until the blades have completely
stopped;
GG
don’t accidentally unscrew the goblet or
mill jar/lid from the blade assembly.
2
G
Never run the blender empty.
G
Never blend more than the maximum
capacity stated in the recommended usage
chart.
G
To ensure long life of your blender or mill, do
not run it continuously for longer than 60
seconds.
G
Smoothie recipes - never blend frozen
ingredients that have formed a solid mass
during freezing, break it up before adding to
the goblet.
G
Do not process hard spices such as Nutmeg
or Turmeric root as they may damage the
blade.
G
Do not use the blender as a storage
container. Keep it empty before and after
use.
G
Always use the blender on a secure, dry level
surface.
G
Never place this appliance on or near a hot
gas or electric burner or where it could touch
a heated appliance.
G
This appliance shall not be used by children.
Keep the appliance and its cord out of reach
of children.
G
Misuse of your blender can result in injury.
G
Appliances can be used by persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and if they
understand the hazards involved.
3
G
Only use the appliance for its intended
domestic use. Kenwood will not accept any
liability if the appliance is subject to improper
use, or failure to comply with these
instructions.
G
The maximum rating is based on the
attachment that draws the greatest load.
Other attachments may draw less power.
safety
IMPORTANT: HOT BLENDING
INSTRUCTIONS
To minimise the possibility of scalding when
blending hot ingredients keep hands and
other exposed skin away from the lid to
prevent possible burns. The following
precautions must be observed:
G
CAUTION: Blending very hot
ingredients may result in hot liquid
and steam being forced suddenly
past the lid or filler cap
G
We recommend that hot ingredients
are allowed to cool before blending.
G
NEVER exceed 1200ml / 5 cups capacity
if processing hot liquids, such as soups
(refer to the markings on the goblet).
G
ALWAYS commence blending at a low
speed and gradually increase the speed.
NEVER blend hot liquids by using the
pulse setting.
G
Liquids which tend to foam such as milk,
should be limited to a maximum capacity of
1000ml/4 cups.
.
4
G
Take care when handling the blender as the
goblet and its contents will be very hot.
G
Take particular care when removing the lid.
The lid is designed to be a tight fit to
prevent leakage. If necessary protect your
hands with a cloth or oven gloves when
handling.
G
Ensure the goblet is securely attached to
the base and when removing from the
appliance, guide the base and ensure it is
removed together with the goblet.
G
Ensure that the lid and filler cap are
securely in place before every blending
operation.
G
Always ensure that the vents in the filler cap
are clear before every blending operation
.
G
When fitting the lid to the goblet always
ensure that the lid and goblet rim are clean
and dry to ensure a good seal and prevent
spillage.
before plugging in
G
Make sure your electricity supply is
the same as the one shown on the
underside of the appliance.
Important - UK only
G
The wires in the cord are coloured
as follows:
Blue = Neutral
Brown = Live.
G
The appliance must be protected by
a 13A approved (BS1362) fuse.
Note:
G
For non-rewireable plugs the fuse
cover MUST be refitted when
replacing the fuse. If the fuse cover
is lost then the plug must not be
used until a replacement can be
obtained. The correct fuse cover is
identified by colour and a
replacement may be obtained from
your Kenwood Authorised Repairer
(see Service).
G
If a non-rewireable plug is cut off it
must be DESTROYED
IMMEDIATELY. An electric shock
hazard may arise if an unwanted
non-rewireable plug is inadvertently
inserted into a 13A socket outlet.
5
G
his appliance conforms to EC
T
directive 2004/108/EC on
lectromagnetic Compatibility and
E
C regulation no. 1935/2004 of
E
27/10/2004 on materials intended
or contact with food.
f
se your blender for soups, drinks,
U
âtés, mayonnaise, breadcrumbs,
p
biscuit crumbs, chopping nuts and
crushing ice. Use your multi mill (if
supplied) for milling herbs, nuts,
coffee beans and purées.
key
filler cap
lid
vents
goblet
sealing ring
blade unit
blade base
power unit
Power On indicator
speed + pulse control
TYPE BLM61 & BLP61 only
Programme buttons
drinks
ice crush
rinse
Multi mill (if supplied)
multi mill jar
grinding mill (if supplied)
mill lid
grinding mill blade assembly
grating mill (if supplied)
mill lid
grating mill blade assembly
to use your blender
1 Fit the sealing ring into the blade
unit - ensuring the seal is located
orrectly in the grooved area.
c
G
Leaking will occur if the seal
is damaged or incorrectly
itted.
f
2 Clip the blade unit into the base
.
3 Screw the blade assembly onto the
goblet – ensuring the blade
assembly is fully tightened . Refer
to the graphics on the underside of
the blade unit as follows:
- unlocked position
- locked position
4 Put your ingredients into the goblet.
5 Fit the filler cap to the lid and push
down to secure.
6 Fit the lid by pushing down until
secure.
7 Place the blender onto the power
unit .
G
The appliance will not work if
the blender is incorrectly
fitted.
8 Plug in and the indicator light will
remain unlit whilst in the “O” OFF
position.
TYPE BLM60 & BLP60 - Turn
the speed control to select a speed
(refer to the recommended usage
chart).
G
Select a speed between ‘Min’ to
‘Max’ by turning the speed control.
At the end of blending return the
speed control to “O” OFF before
removing the blender.
G
Do not remove the goblet until the
blades have stopped rotating and
the speed control is in the “O” OFF
position.
G
(P) Pulse – operates the motor in a
start/stop action. The pulse will
operate for as long as it is held in
position.
Note: If the blender is removed from
the power unit whilst a speed is
selected the Indicator light will go
out and the blender will stop. The
blender willl restart immediately if
refitted.
6
YPE BLM61 & BLP61 only -
T
Turn to the “on” position and the
ower On indicator and the 3
P
re-programmed buttons will light
p
up.
ote: In the “on” position the Power
N
n indicator will flash if the goblet is
O
not fitted to the power unit.
n the “O” OFF position all the
I
ndicator lights will remain off.
i
9 Select a speed (refer to the
recommended usage chart). Choose
one of the following options:
G
Select one of the 3 pre-programmed
buttons. When the required
programme button is pressed the
light on the other button will go out.
The blender will switch off
automatically at the end of the preset time. If you wish to stop before
the pre-set time, press the selected
programme button again.
G
Select a speed between ‘Min’ to
‘Max’ by turning the speed control.
At the end of blending return the
speed control to “O” OFF before
removing the blender.
G
Do not remove the goblet until the
blades have stopped rotating and
the speed control is in the “O” OFF
position.
G
(P) Pulse – operates the motor in a
start/stop action. The pulse will
operate for as long as it is held in
position.
Refer to the troubleshooting
section if you experience any
problems with the operation of
the blender.
hints
G
To blend dry ingredients - cut into
pieces, remove the filler cap, then
with the machine running, drop the
pieces down one by one. Keep your
hand over the opening. For best
results empty regularly.
G
The processing of spices is not
recommended as they may damage
the plastic parts.
G
hen making mayonnaise, put all
W
the ingredients, except the oil, into
he blender. Remove the filler cap.
t
hen, with the appliance running,
T
add the oil slowly through the hole in
he lid.
t
G
hick mixtures, e.g. pâtés and dips,
T
may need scraping down. If the
ixture is difficult to process, add
m
ore liquid.
m
7
Recommended Usage Chart (Programme buttons)
rogrammeUsage/FoodMax.Programme
P
ButtonItemsRecommendedTime
Cold LiquidsMax 1.6 litres60 secs
rinks & Cocktails
D
ilkshakes and milkMax 1.2 litres
M
based drinks
moothies1 litre Liquid
S
Drinks
IceA change in speed will be
crushnoted - this is normal.
Rinse
Processing times stated are for guidance only and will vary depending on the
exact recipe used, ingredients being processed and personal preference. Stop the
processing when the desired result has been achieved.
Place the fresh fruit and
liquid ingredients in first
(includes yoghurt, milk
and fruit juices).
Then add ice or frozen
ingredients (includes
Freeze fruit juice in ice
trays for Slushie type
drinks
A change in speed will beMax 500 mls30 secs
noted - this is normal.warm water
Use to rinse the goblet
before taking apart
for cleaning.
For best results always
take the blender apart for
cleaning and dry
thoroughly before
re-assembling.
Use your multi mill for milling herbs,
nuts, coffee beans and purees.
1 Put your ingredients into the jar .
Fill it no more than half full.
2 Fit the blender sealing ring into
the blender blade unit - ensuring
the seal is located correctly in the
grooved area.
G
Ensure that the seal is fitted
correctly.
3 Clip the blade unit
.
4 Turn the blade unit
Lower it into the jar, blades down
and turn to lock - ensuring the blade
assembly is fully tightened
to the graphics on the underside of
the blade unit as follows:
Recommended Usage Chart (Manual control)
Soups using milk1 litre
e recommend that hot ingredients are allowed to cool
W
before blending. However should you wish to process
ot ingredients please read the Hot Blending Safety
h
instructions.
Drinks & Cocktails
Milkshakes and milkMax 1.2 litresMax15 - 30 secs
based drinks
Smoothies1 litre LiquidMax30 - 60 secs
Place the fresh fruit and
liquid ingredients in first
(includes yoghurt, milk
and fruit juices).
Then add ice or frozen
ingredients (includes
frozen fruit, ice or ice
cream)
short bursts until(200g)
crushed to the desired
consistency
5 Place the mill onto the power unit
.
6 Select a speed or use the pulse
control.
to use your grinding mill
(if supplied)
Suitable for grinding spices, coffee
beans and processing ginger, garlic
and chillies.
1 Place your ingredients into the blade
into the base
upside down.
- unlocked position
- locked position
assembly
2 Fit the lid
3 Place the mill onto the power unit.
4 Select a speed or use the pulse (P)
control.
. Refer
.
and turn to lock .
9
to use your grating mill
(if supplied)
Suitable for grating parmesan
cheese, nutmeg, coconut and dried
ruit.
f
1 Place your ingredients into the blade
assembly
Fit the lid
2
3 Place the mill onto the power unit.
4 Select a speed or use the pulse (P)
control.
ingredientsmillmax qtyspeed operating
Herbs - best choppedMulti15gMAX5 – 10 secs
when clean and dry
NutsMulti or Grinding50gMAX10 – 15 secs
Coffee BeansMulti or Grinding50gMAX30 secs
Baby Foods & PureesMulti50gMAX30 secs
Lean beef, cut intoMulti70gMAX5 secs
2.5 cm cubes
Spices – such as blackGrinding50gMAX30 – 60 secs
peppercorns, cardamom
seeds, cumin seeds,
coriander seeds, fennel
seeds, whole cloves etc.
ChilliesGrinding30gMAX10 secs
Fresh Root GingerGrinding30gMAX10 secs
GarlicGrinding4 clovesMAX10 secs
Parmesan Cheese – cut Grating60gMAX10 secs
into 1cm cubes
Dried FruitGrating50gMAX10 secs
CoconutGrating50gMAX20 secs
NutmegGrating2MAX40 secs
hints
G
For optimum performance when
processing spices we recommend
that you do not process more than
50g at a time in the mill.
G
Whole spices retain their flavour for
a much longer time than ground
spices so it is best to grind a small
quantity fresh at a time to retain the
flavour.
G
To release the maximum flavour and
essential oils whole spices are best
roasted prior to milling.
G
Baby food/purees - allow cooked
food to cool to room temperature
before processing in the mill.
.
nd turn to lock
a
.
mill recommended speed chart
care and cleaning
G
Always switch off, unplug and
dismantle before cleaning.
G
Empty the goblet before unscrewing
it from the blade unit.
G
Do not immerse the blade unit in
water.
G
The goblet can be washed in your
dishwasher.
power unit
G
Wipe with a damp cloth, then dry.
G
Do not immerse the power unit in
water.
time
10
lade assemblies
b
blender and multi mill
G
emove the blade unit from the
R
oblet or mill by turning to the
g
unlock positionto release.
grinding and grating mills
G
emove the lid from the blade
R
ssembly.
a
1 blender/multi mill: remove and
wash the sealing ring.
2 Don’t touch the sharp blades –
brush them clean using hot soapy
water, then rinse thoroughly under
the tap. Don’t immerse the
blade unit in water.
3 Leave to dry upside down.
other parts
Wash by hand, then dry.
service and customer
care
G
If the cord is damaged it must, for
safety reasons, be replaced by
KENWOOD or an authorised
KENWOOD repairer.
If you experience any
problems with the operation
of the blender, before calling
for assistance refer to the
troubleshooting guide.
UK
If you need help with:
G
using your appliance or
G
servicing, spare parts or repairs (in or
out of guarantee)
call Kenwood customer care on 023
9239 2333. Have your model
number (ie BLM60 or BLP60)
and date code (5 digit code ie
13L35) ready. They are on the
underside of the power unit.
G
spares and attachments
call 0844 557 3653.
G
other countries
Contact the shop where you bought
your appliance.
MPORTANT INFORMATION FOR
I
CORRECT DISPOSAL OF THE
RODUCT IN ACCORDANCE
P
ITH EC DIRECTIVE
W
2002/96/EC.
At the end of its working life, the product
must not be disposed of as urban
waste.
It must be taken to a special local
authority differentiated waste collection
centre or to a dealer providing this
service.
Disposing of a household appliance
separately avoids possible negative
consequences for the environment and
health deriving from inappropriate
disposal and enables the constituent
materials to be recovered to obtain
significant savings in energy and
resources. As a reminder of the need to
dispose of household appliances
separately, the product is marked with
a crossed-out wheeled dustbin.
guarantee (uk only)
If your blender goes wrong within
one year from the date you bought
it, we will repair it (or replace it if
necessary) free of charge provided:
G
you have not misused, neglected or
damaged it;
G
it has not been modified (unless by
Kenwood);
G
it is not second-hand;
G
it has not been used commercially;
G
you have not fitted a plug incorrectly;
and
G
you supply your receipt to
show when you bought it.
This guarantee does not affect your
statutory rights.
G
Designed and engineered by
Kenwood in the UK.
G
Made in China.
11
troubleshooting guide
ProblemCauseSolution
The Blender will notNo Power/Power OnCheck blender
operate.Light not illuminated.plugged in.
Blender not assembledCheck blade unit is
orrectly.fully tightened to
c
Power On Light flashingThe blender has been leftTurn the speed
slowly.plugged in and in the ‘on’control to the
(BLP61/BLM61 only)position for more than 15“O” OFF position,
minutes and has gone intowait 5 seconds and
standby mode.then turn to “on” to
BLP61/BLM61 Blender not Goblet fitted and speed control Either select a speed
operating but Power Onturned to “on” but speed ormanually or press
and programme buttonprogramme not selected.one of the
lights on.programme buttons.
Power on light flashingThe goblet is removed fromTurn the speed
rapidly (BLP61/BLM61 only) the power unit without turning control to “O” OFF
the speed control to “O” OFF. and reselected a
Programme buttons notProgramme buttons willTurn the speed
operatingnot operate unless the speed control to “on” and
control is turned to the “on”select the required
position first.programme.
Blender leaking from blade Seal missing.Check seal is fitted
assembly.Seal incorrectly fitted.correctly and not
Seal damaged.damaged. To obtain
Blender seal missing from The seal is packed pre-fitted Unscrew goblet and
blade unit when removedto the blade unit.check that seal is
from packaging.fitted to blade unit.
If none of the above solve the problem see “Service & Customer Care”.
the goblet.
reset.
speed.
a replacement seal
see “service &
customer care”.
To obtain a
replacement seal
see “service &
customer care”.