Kenmore BL220 Installation Manual

BL220 series, BL230 series BL240 series

instructions

English 2 - 6

´¸∂w

7 - 01

HEAD OFFICE: Kenwood Limited, 1-3 Kenwood Business Park, New Lane, Havant, Hampshire PO9 2NH

41089/1

English

햲

햳

햴

햵

햶



햷

햸







햹

햺

햻

햽

se your blender for soups, drinks,

âtés, mayonnaise, breadcrumbs,

p biscuit crumbs, chopping nuts and

rushing ice. Use your mill (if

upplied) for milling herbs, nuts,

s coffee beans and purées.

before using your Kenwood appliance

●

Read these instructions carefully and retain for future reference.

●

Remove all packaging and any labels.

●

Wash the parts: see ‘care and cleaning’.

safety

●

Switch off and unplug:

●●

before fitting or removing parts;

●●

when not in use;

●●

before cleaning.

●

Never fit the blade unit to the power unit without the blender goblet or mill jar fitted.

●

Always unplug the appliance before putting your hands or utensils in the goblet.

●

Always take care when handling the blade assembly and avoid touching the cutting edge of the blades when cleaning.

●

Only operate the blender with the lid in place.

●

Only use the goblet with the blade assembly supplied.

●

Never let the power unit, cord or plug get wet.

●

Never use a damaged appliance. Get it checked or repaired: see ‘service and customer care’.

●

Never use an unauthorised attachment.

●

Liquids should be allowed to cool to room temperature before blending.

●

Never leave the appliance unattended when it is operating.

●

hen removing the blender or mill

rom the power unit:

●

wait until the blades have

ompletely stopped;

●●

on’t accidentally unscrew the

d goblet or mill jar from the blade assembly.

●

Never run the blender empty.

●

Never blend more than the maximum capacity stated in the recommended speed chart.

●

To ensure long life of your blender, do not run it for longer than 60 seconds or the mill for longer than 30 seconds in any 5 minute period.

●

Smoothie recipes - never blend frozen ingredients that have formed a solid mass during freezing, break it up before adding to the goblet.

●

Don’t use the blender as a storage container. Keep it empty before and after use.

●

Always use the blender on a secure, dry level surface.

●

Never place this appliance on or near a hot gas or electric burner or where it could touch a heated appliance.

●

Important - The skirt on the base of the glass goblet is fitted during manufacture and no attempt should be made to remove it.

●

Misuse of your blender can result in injury.

●

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

●

Children should be supervised to ensure that they do not play with the appliance.

●

Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.

efore plugging in

●

Make sure your electricity supply is

he same as the one shown on the

nderside of the appliance.

mportant - UK only

●

The wires in the cord are coloured

s follows:

lue = Neutral

B Brown = Live.

●

The appliance must be protected by a 3A approved (BS1362) fuse.

Note:

●

For non-rewireable plugs the fuse cover MUST be refitted when replacing the fuse. If the fuse cover is lost then the plug must not be used until a replacement can be obtained. The correct fuse cover is identified by colour and a replacement may be obtained from your Kenwood Authorised Repairer (see Service).

●

If a non-rewireable plug is cut off it must be DESTROYED IMMEDIATELY. An electric shock hazard may arise if an unwanted non-rewireable plug is inadvertently inserted into a 13A socket outlet.

●

This appliance conforms to EC directive 2004/108/EC on Electromagnetic Compatibility and EC regulation no. 1935/2004 of 27/10/2004 on materials intended for contact with food.

key

blender blade assembly

filler cap

  lid

a) plastic = locking lid

) glass = push fit

 goblet  sealing ring  blade assembly  power unit  speed control + pulse

mill (if supplied)

 mill jar  sealing ring (if supplied)  blade assembly (if supplied)  mill lid

Note: A separate blade assembly for the mill will not be supplied with all models, the sealing ring  and  and blade assembly  and  are identical and interchangeable.

to use your blender

1 Fit the sealing ring  into the blade

unit  - ensuring the seal is located correctly in the grooved area.

●

Leaking will occur if the seal is damaged or incorrectly fitted.

2 Screw the blade assembly onto the

goblet . Refer to the graphics on the underside of the blade unit as follows:-

- unlocked position

- locked position

To ensure the blade assembly is fully tightened check that the on the goblet aligns with the on the blade assembly. The blender will

not operate if incorrectly assembled.

3 Put your ingredients into the goblet. 4 Fit the filler cap to the lid.

a glass goblet - Fit the lid by pushing down until secure. b plastic goblet - Fit the lid onto the goblet and turn clockwise until it clicks.

5 Place the blender onto the power

unit and turn clockwise until it clicks .

+ 7 hidden pages