Kenmore 141.17691 User Manual
Owner's Manual
Liquid Propane Gas Grili
Model 141.16691
Grill Information Center; If you have questions about assembiy or grili operation, or if there are
damaged or missing parts when you unpack this unit from the shipping box, cail us 8am-8pm CST,
Monday through Friday at: 1-888-317-7642
WARNING:
Read this Owner's Manual carefuily and be sure
your gas grill is properly assembled, installed and
maintained. Failure to follow these instructions
could result in serious bodily injury and/or property
damage. This gas grill is intended for outdoor use
only and is not intended to be installed in or on
recreational vehicles or boats.
Note to Installer: Leave this Owner's Manual
with the consumer after delivery and/or instailation.
Note to Consumer: Leave this Owner's Manual
in a convenient place for future reference.
Sears, Roebuck and Co.,
Hoffman Estates, IL 60179 U.S.A.
P80106003B - Date: 2004/02/06
Table of Contents
Read These Safety Instructions
Warranty
Safety Instructions
Hardware
Parts Diagram and Lists
....................................................
.....................................
...................................................
......................
2
2
6
7
Assembly Instructions..............................10
Lighting Instructions.............................16
Cleaningand Maintenance Instructions .... 18
Frequently Asked Questions
...................
20
Cooking Instructions...........................A-1
Cooking Guide and Recipes
.............
A-2
Kenmore Elite Grili Warranty
For the Lifetime of this Kenmore Eiite Griii, Sears
will repair or replace, at our option, any Exterior
Stainless Steel or Aluminum Casting Parts (except for
paint loss).
Full 2-Year Warranty on Grill:
For 2 years from the date of purchase Sears will repair
or replace, at our option, any grill part (except for paint
loss, rusting and ignitor battery) that is defective in
material or workmanship.
Limited 3 Year Warranty on Selected Grill Parts:
From 2 years after the date of purchase for a 3-year
period. Sears will replace FlameTamers, Cooking
Grids, Burners and All Other Parts (except for ignitor
battery) ifthey are defective in material or workman
ship. You will be charged for labor.
Warranty Service
Warranty service is available by contacting the @
nearest Sears Service Center at 1-800-4-MY-HOME
Awarning
Combustion byproducts produced when using
this product contain chemicals known to the
State of California to cause cancer, birth
defects, or other reproductive harm.
Awarning
Failure to comply with these instructions
could result in a fire or explosion that
could cause serious bodily injury, death, or
property damage.
Awarning
Your grill will get very hot. Never lean over
the cooking area while using your grill. Do not
touch cooking surfaces, grill housing, Lid or any
other grill parts while the grill is in operation, or
until the grill has cooled down after use.
Failure to comply with these instructions
may result in serious bodily injury.
Awarning
(a) Do not store a spare LP-gas cylinder
under or near this appliance;
(b) Never fill the cylinder beyond 80 percent
full; and
(c) If the information in "(a)" and "(b)" is not
followed exactly, a fire causing death or
serious injury may occur.
FOR YOUR SAFETY
1. Do not store or use gasoline or other flam
mable material and liquids in the vicinity of this
or any other appliance.
2. A LP cylinder not connected for use must not
be stored in the vicinity of this or any other
appliance.
_________________________________
FOR YOUR SAFETY
If you smell gas:
I.Shut off gas to the appliance.
2. Extingui^ any open flame such as candle,
cigarette, lighter, etc., that could cause gas to
ignite.
3. Open the Grill Lid.
4. if odor continues, immediately call your gas
supplier or your fire department.
Warranty Restrictions
• This warranty is void if grill is used for com
mercial or rental purposes.
• This warranty applies only when the grill is
used in the United States.
• This warranty gives you specific legal rights,
and you may also have other rights which vary
from state to state.
Sears, Roebuck and Co., Dept. 817WA,
Hoffman Estates, IL 60179
LP Gas Safety Instructions
IMPORTANT: Your Kenmore LP Gas Grill cannot
be converted to use Natural Gas. Attempting to do
so is extremely hazardous and will also void the
grill warranty.
Grill Installation Codes
The installation must conform with local codes or, in
the absence of local codes, with either the National
Fuel Gas Code, ANSI Z223.1/NFPA 54, or CAN/
CGA-B149.1, Natural Gas and Propane Installation
Code.
Sears, Roebuck and Co.
Correct LP Gas Tank Use
LP gas grill models are desgned for use with a
standard 20 lb. Liquid Propane Gas (LP gas) tank,
not included in grill box. Never connect your gas
rill to an LP gas tank that exceeds this capacity.
I tank of approximately 12 inches in diameter by
18-1/2 inches high is the maximum size LP gas
tank to use. You must use an "OPD” gas tank
which offers a listed Overfill Prevention Device.
This safety feature prevents tank from being overfilled
which can cause malfunction of LP gas tank,
regulator and/or grill.
The LP gas tank must be constructed and mariied
in accordance with the Specifications for LP-Gas
Cylinders of the U.S. Department of Transportation
(D.O.T.) or the National Standard of Canada, CAN/
CSA-B339, Cylinders, Spheres and Tubes for Trans
portation of Dangerous Goods; and Commission, as
applicable.
1. The LP gas tank has a shutoff valve, termi
nating in an LP gas supply tank valve outlet,
that is compatible with a Type 1 tank con
nection device. The LP gas tank must also
have a safety relief device that has a direct
connection with the vapor space of the tank.
2. The tank supply system must be arranged
for vapor withdrawal.
3. The LP gas tank used must have a collar
to protect the tank valve.
LP gas tanks must be stored outdoors in a
well-ventilated area and out of the reach of
children. Disconnected LP gas tanks must not
be stored in a building, garage or any other
enclosed area.
When your gas grill is not in use the gas
must be turned off at the LP gas tank.
The regulator and hose assembly can be seen
after opening the doors (if applicable), must be
inspected before each use of the grill. If there
is excessive abrasion or wear or if the hose is
cut, it must be replaced prior to the grill being
used again.
Keep the gas regulator hose away from hot
grill surfaces and dripping grease. Avoid unnec
essary twisting of hose. Visually inspect hose
prior to each use for cuts, cracks, excessive
wear or other damage. If the hose appears
damaged do not use the gas grill. Call Sears
at 1-800-4-MY-HOME®(1-800-469-4663) for a
Sears authorized replacement hose.
Never light your gas grill with the lid closed or
before checking to ensure the burner tubes are
fully seated over the gas valve orifices.
Never allow children to operate your grill. Do
not allow children to play near your grill.
Proper Placement and Clearance of Grill
Never use your gas grill in a garage, porch, shed,
breezeway or any other enclosed area. Your gas grill is
to be used outdoors only, at least 24 inches from the
back and side of any combustible surface. Do not
locate thi s appi I ance u nder overhead u nprotected
combustible surfaces. Do not obstruct the flow of
ventilation air around the gas grill housing.
This outdoor gas grill is not intended to be installed in
or on recreational vehicles and/or boats.
• Never connect an unregulated LP gas tank to
your gas grill. The gas regulator assembly
supplied with your gas grill is adjusted to have
an outlet pressure of 11" water column (W.C.)
for connection to an LP gas tank.
• Only use the regulator and hose assembly
supplied with your gas grill. Replacement
regulators and hose assemblies must be those
specified by Sears.
• Have your LP gas tank filled by a reputable
propane gas dealer and visually inspected and
re-qualified at each filling.
• Never fill the gas tank beyond 80% full.
Have your propane gas dealer check the
release valve after every filling to ensure that it
remains free of defects.
• Always keep LP gas tanks in upright position.
Do not store (or use) gasoline or other flammable
vapors and liquids in the vicinity of this gas grill.
• LP gas tanks not connected for use must NOT be
stored on bottom shelf or in the vicinity of this or
any other gas grill.
• Do not subject the LP gas tank to excessive heat.
• Never store an LP gas tank indoom. If you
store your gas grill in the garage or other indoor
location, always disconnect the LP gas tank
first and store it safely outside.
•
Awarning
If you smell gas:
• Shut off gas supply to the gas grill.
• Turn the Control Knobs to OFF position.
• Extinguish any open flame such as candle,
cigarette, lighter, etc., that could cause gas
to ignite.
• Open the Grill Lid.
• Get away from the LP gas tank.
• Do not try to fix the problem yourself.
• If odor continues or you have a fire you
cannot extinguish, cal! your fire depart
ment. Do not cal! near the LP gas tank
because your telephone is an electrical
device and could create a spark resulting
in fire and/or explosion.
NOTE: The normal flow of gas through the
regulator and hose assembly can create a
humming noise. A low volume of noise is
perfectly normal and will not interfere with
operation of the grill. If humming noise is
loud and excessive you may need to purge
air from the gas line or reset the regulator
excess gas flow device. This purging proce
dure should be done every time a new LP
gas tank is connected to your grill. For help
call the Grill Information Center for assis
tance, Sam - 8pm CST, Monday through
Friday 1-888-317-7642.
Natural Gas Safety Instructions
Figure 1 (Natural gas model only)
IMPORTANT: your Kenmore Natural Gas Grill cannot
be converted to use LP Gas. Attempting to do so
is extremely hazardous and will also void the grill
warranty.
• Your natural gas grill is designed to operate on
natural gas only, at a pressure of 7" water column
(W.C.) (1/4 psi or 1.75 kpa), regulated at the
residential meter. Check with your gas utility
company for local gas pressure and with your
local municipality for building code requirements. If
your residential gas line pressure has not been
regulated to 7" W.C., contact your local gas utility
company for professional assistance.
• it is recommended that a Shutoff Valve be installed
at the gas supply source outdoors, install at a point
after the gas pipe exits the outside wail and before
the quick-disconnect hose, or install it at the point
before the gas line piping enters the ground.
See Figure 1.
• Pipe seal I ng com pound or pi pe thread tape resi stant
to the action of natural gas must be used on all male
pipe threads when making the connection.
• Disconnect your gas grill from fuel source when
the gas supply is being tested at high pressures.
Thisgas grill and its individual shutoff valve must
be disconnected from the gas supply pipe system
during any pressure testing of that system at
pressure in excess of 1/2 psi (3.5kpa).
•
GAS SUPPLY
DISCONNECT
• Turn off your gas grill when the gas supply is
being tested at low pressures. The grill must be
isolated from the gas supply pipe system by
closing its individual manual shutoff valve during
any pressure testing of the gas supply pipe
system at pressures equal to or less than 1/2 psi
(3.5kpa).
CAUTION: bevVARE OF FLASHBACK
Flashback Prevention
CAUTION: Spiders and smaii insects occa
sionally spin webs or make nests in the gril!
Burner Tubes during transit and warehousing.
These webs can lead to a gas fiow obstruc
tion which couid result in a fire in and around
the Burner Tubes. This type of fire is known
as a "FLASHBACK" and can cause serious
damage to your grili and create an unsafe
operating condition for the user.
To reduce the chance of "FLASHBACK", you
must clean the burner tubes before assembiing your grill, and at ieast once a month in
late summer or early fail when spiders are
most active. Also perform this Burner Tube
cleaning procedure if your grill has not been
used for an extended period of time.
Figure 1
To reduce the chance of "FLASHBACK" (see
CAUTION at left) clean the Burner Tubes and
Burners before fully assembling your grili.
Remove the Cotter Pin from the rear underside
of each Burner using a pair of long nose pliers.
Carefully lift each Burner up and away from the
Gas Valve Orifice, then refer to Figure 1 and
perform one of these three cleaning methods:
1.
Bend a stiff wire, (a lightweight coat hanger
works well) into a small hook as shown
below. Run the hook through the Burner Tube
and inside the Burner several times to remove
any debris.
c
2.
Use a bottle brush with a flexible handle.
Run the brush through the Burner Tube and
inside the Burner several times, removing any
debris.
3.
Use an air hose to force air through each
Burner Tube. The forced air should pass
debris or obstructions through the Burner and
out the Ports.
GAS COLLECTOR BOX
Awarning
The location of the Burner Tube with re
spect to the Orifice is vital for safe opera
tion. Check to ensure the Orifice is inside
the Burner Tube before using your gas grill.
See Figure 2. if the Orifice is not inside
the Burner Tube, lighting the Burner may
cause explosion and/or fire.
Figure 2
Tools Required for Assembly
• #2 Phillips screwdriver
• Protective work gloves
• Eye protection
• Utility knife
Contents for Hardware Pack/LPG (Part #P06001019A)
The foilowing tabie iilustrates a breakdown of the hardware pack. It highlights what components are used
in the various stages of assembly.
Ref.
S122G04121
Component Qty.
Phiilips Head Screw 1/4"x3/4"
S142G04121 Countasink Fiat Head Screw 1/4"x3/4'
P05301001A
P05301003A
AA Battery 2
9V Battery 1
Size and Quantity of each Hardware Piece:
-WWW
Phillips Head Screw 1/4"x3/4"
Qty. 4
Ref. # S122G04121
AA Battery
Qty. 2
Ref. # P05301001A
Scale 1:2
Purpose of Components
Attaches Side Shelf To Grili Head
4
4
Attaches Cart Side Handle To Grili Head
Powers The Electric ignitor
Powers The Fuel Gauge Display (LPG model only)
\
m W'
Countersink Flat Head Screw 1/4"x3/4"
Qty. 4
Ref. # S142G04121
9V Battoy (LPG model only)
Qty. 1
Ref. # P05301003A
Scale 1 ;2
Contents for Hardware Pack (Part #P06001020A) (NG)
The following tabie iilustrates a breakdown of the hardware pack. It highlights what components are used
in the various stages of assembly.
Ref.
S122G04121
S142G04121
P05301001A
Component
Phillips Head Screw 1/4"x3/4"
Countersink Rat Head Scaow 1/4"x3/4'
AA Battery 2
Size and Quantity of each Hardware Piece:
m№\m
M
Phillips Head Screw 1/4"x3/4"
Qty. 4
Ref. # S122G04121
AA Battery
Qty. 2
Ref. # P05301001A
Scale 1:2
Qty.
Purpose of Components
4 Attaches Side Shelf To Grill Head
Attaches Cart Side Handle To Grili Head
4
Powers The Electric Ignitor
j\
WWW
Countersink Flat Head Screw 1/4"x3/4“
Qty. 4
Ref. # S142G04121
Model 141.16691 & 141.17691 Parts Diagram
LPG = Liquid Propane Gas
NG = Natural Gas
53(LPG only)
67
(LPG only)71
(NG otily)72
73 (LPG only)
62 (NG only)
61 (NG only)
Model 141.16691 & 141.17691 Parts List
RERÍ
1
2
3
4
5 Name Plate
6
7
8 Cooking Grid/Smaii
9 Fíame Tamer/Large
10
11 Burner/Main
11a
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30a
30b
31
32
33
34
35
36
37
38
39
40
41 Cart Bottom Shelf (NG only)
42
43
44
45
46
47
48
DESCRIPTION
Lid
Lid Trim Plate
Temperature Gauge
Lid Handie
Cooking Rack/Secondary
Cooking Grid/Large
Fíame Tamer/Smail
Burner Air Shutter/Main (NG oniy)
Burner Bracket
Gas Coliector Box with Electrode
Electric Wire Set
Electric Ignitor, 4-Ports
Electric Ignitor, 2-Ports
Bowl Panel, Left
Bowl Panel, Outside Left
Bowl Pane!, Right
Bowl Pane!, Outside Right
Bowl Panel, Front
Bowl Pane!, Rear
Bowl Wind Shield, Upper
Bowl Wind Shield, Lower Left
Bowl Wind Shield, Lower Right
Grease Draining Tray
Grease Draining Tray Heat Shield
Gas Valve/Manifold Assembly (LPG)
Gas Valve/Manifold Assembly (NG)
Control Pane! (LPG)
Control Pane! (NG)
Protective Pad, Lid Front
Protective Pad, Lid Rear
Control Knob for Main/Side Burners
Control Knob Seat
Back Burner Assembly
Back Burner Electrode
Back Burner Orifice (LPG)
Back Burner Orifice (NG)
Back Burner Extension Tube
Control Knob for Back Burner
Side Shelf, Left
Cart Side Handle
Cart Bottom Shelf (LPG only)
Cart Legs with Side Panel, Left
Cart Legs with Side Panel, Right
Cart Rear Panel (LPG only)
Cart Rear Panel (NG only)
Door Bracket
Door, Left
Door, Right
PART#
P0011903AA
P0011435EA
P00601171A
P00205033B
P00410038C
P01518001B
P01606032B
P01606033B
P01708031B
P01708032B
P02001004E
P05524004A
P02206271B
P02608050C
P02615053A
P02502024C
P02502012C
P00720293C
P00742296C
P00721293C
P00743296C
P00738303C
P00725303C
P00737303C
P06906005C
P06906007C
P02714012F
P06903009D
Y0060083
Y0060131
P02911291N
P02911291T
P05518100!
P05518004!
P03419033H
P03415264A
P02007049D
P02614006B
P06509010A
P06509016A
P03717033A
P03419043H
P01106028B
P00205032B
P01005026H
P01005034H
P07614001A
P07615001A
P07701021A
P07701022A
P03302007C
P04302012A
P04303012A
QT
1
1
1
1
1
1
3
1
3
1
6
6
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
7
8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Model 141.16691 & 141.17691 Parts List
RERf DESCRIPTiON
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
— Hardware Pack (LPG)
...
Door Trim Plate, Left
Door Trim Plate, Right (LPG)
Door Trim Plate, Right (NG)
Cart Partition Panel
Cart Decorative Pane!
Cart Decorative Panel, Trim Plate
Door Hinge Bracket, Upper/Left
Door Hinge Bracket, Lower/Left
Door Hinge Bracket, Upper/Right
Door Hinge Bracket, Lower/Right
Door Magnet
Door Handle
Cart Spice Basket (LPG)
Cart Spice Basket (NG)
Cart Spice Basket Division Wire
Tank Pull-Out Tray Assembly (LPG only)
Fuel Gauge Display (LPG only)
Caster, 3-1/2" in., with Brake
Side Burner Lid
Side Burner Body
Side Burner Pot Support
Side Burner Electrode
Side Burner with Brass Ring
Regulator with Hose/LPG
Hose, 12ft./NG
Wire Fastener (LPG only)
Lighting Tube
Hardware Pack (NG)
Owner's Manual
PART# QTY
P07506007A 1
P07507007A 1
P07507008A 1
P07512013A 1
P07501008A 1
P07509009A 1
P03314018C
P03314019C
P03314020C
P03314021C
P05523002K 4
P00205036B 2
P05204010E 1
P05204010E 2
P05204012E 1
Y0340014 1
P05310002B 1
P05115020A 4
P00115346A 1
P02301006B 1
P00805013B 1
P02607052C
P02002055D 1
P03601001A 1
P03703001A 1
P05310040A 1
P05313004C
P06001019A 1
P06001020A 1
P80106003B 1
1
1
1
1
1
1
For the repair or replacement parts you need: Call anytime
1-800-4-MY-HOME ®(1-800-469-4663)
To make sure you obtain the correct replacement parts for your Kenmore gas grill, please refer to the
part numbers in this parts list. The foliowing information is required to assure you receive the correct
parts:
1. Grill Model Number (see CSA label on grill)
2. Part Number
3. Part Description
4. Quantity of parts needed
Important: Keep this Owner's Manual for convenient referral and for part replacement.
Important: Use only Sears authorized parts. The use of any part that is not Sears authorized can be
dangerous and wili also void your product warranty.
Grill Information Center: If you have questions about assembly or grill operation, or if there are
damaged or missing parts when you unpack this unit from the shipping box, call us Sam -8pm GST,
Monday through Friday at: 1 - 888-317-7642
Assembly instructions
CAUTiON : While it is possible for one person to
assemble this grill, obtain assistance from another
person when handling some of the larger, heavier
pieces.
1. Open the parts boxes. Use the parts list to check
that all parts have been included.
2. inspect the grill fordanage as you ^semble it. Do
not assemble or operate the grill if it appears
damaged. If there are damaged or missing parts
when you unpack the shipping box, or you have
questions during the assembly process, call;
1-888-317-7642 8a.m.-8p.m CST, Mon.-Fri,
Installing Side Shelf and Cart Side Handle
1. Remove the \siiite protective film from the
stainle® steel Side Shelf.
2.
Enlisting the aid of an assistant, attach Side
Shelf to left side of grill. Align the holes on Side
Shelf with the threaded holes on left Outside Bowl
Panel. Tighten securely using 4 of the 1/4"xS4"
Phillips Screvra provided.See Figure 1.
Figure 1
S122G04121 Qty. 4
Phillips Head Screw 1/4"x3/4"
Enlisting the aid of an assistant, attach Cart Side
3.
Handle to right side of grill. Align the holes on
Cart Side Handle with the threaded holes on
right Outside Bo\M Panel. Tighten securely using
4 of the 1/4"x3/4" Flat Head Screvra provided.
See Figure 2.
S142G04121 Qty. 4
Countersink Flat Head Screw
1/4"x3/4"
Ignition Battery Installation - See Figure 3
1. Remove the Ignitor Cap located on the grill
Control Panel.
2. Place the supplied AA battery into the Ignitor
Slot. Be sure to place the positive pole facing
toward you. See
3. Place the Cap and Spring over the AA battery
then tighten the Ignitor Cap onto the grill
Control Panel.
Figure 3.
Figure 3
4. Repeat step 1 through 3 to install
the other
AA battery into the Ignitor Slot.
IMPORTANT: Remove any protective film
from outside and inside of Grill Head.
Before use of this grill please refer to
Cleaning Exterior Stainless Steel Surfaces
found on page 18 of this Owner's Manual.
Electrode Check - Requires an Assistant
Before placing the cooking components into your
grill, ensure that the Spark Electrode Tip is properly
positioned vidthin each Gas Collector Box { a 4"
wide stainless mechanian found at the front be
tween each set of Burners.) The easiest way to
ensure this is to perform this Electrode Check:
1. Be sure all Control Knobs are set to "OFF”
and open the Grill Lid.
2. Have an assistant stand behind to the right of
the grill and look down at each Gas Collector
Box. NEVER put your face inside Grill Head.
3. Press the Ignitor Cap. You should hear a
"clicking" sound and your assistant should see
a small blue spark within each Gas Collector
Box. If a spark is present the Electrode Tips
are properly positioned.
Installing Cooking Components
Important: Before cooking on your grill the first
time, wash the Cooldng Grids and Cooldng Rack
with warm, soapy water. Rinse and dry thoroughly.
After cooking is completed, turn grill to HIGH
setting three to five minutes to bum off rear grease
or food residue.
1. Place the four Stainless Steel Flame Tamers on
the lower ledge above Burners. See Figure 5.
2. Evenly space the Stainless Steel Cooking Grids
(cross braces are bottom side) on the ledge
above the Flame Tamers.
3. Place the Stainless Steel Secondary Cooking
Rack into the slots on the upper left and
upper right of Grill Bow! Side Panels. See
Figure 5.
4. if no spark is seen the Spark Gap shown in
Figure 4 needs to be adjusted as follows:
• Using an adjustable wrench, loosen the Inside
Nut just until the Gas Collector Box can be
maneuvered and turned upward.
• The gap between the Spark Electrode Tip and
Spark receiver should be approximately 3/16".
• if the gap is wider than 3/16" use a pai r of long
nose pliers and gently squeeze the Gas Collector
Box until the gap is correct.
• Return the Gas Collector Box to its original hori
zontal position, secure the inside Nut and try the
Electrode Check again.
5. if no "clicking" sound is heard check the following
common causes. If you need assistance call our
Grill Information Center
at 1-888-317-7642.
• ignitor AA battery not installed properly.
• Electric wires may be loose. Remove the AA
battery, inspect the Ignitor Junction Box found
behind the Control Panel, and connect any loose
wires.
Figure 4 - Side View Figure
4. Remove Fastening Band from Pot Support and
place the Pot Support into the Side Burner
Body-Inner. See Figure 5.
Figure 5
SIS SECONDARY
GAS COLLECTOR BOX
11
Loading...