Kawai MP 7 SE operation manual

Introduction

Main Operation

EDIT Menu

STORE Button & SETUPs

Owner’s Manual

Recorder

USB Menu

SYSTEM Menu

Appendix

Thank you for purchasing this Kawai MP7SE stage piano.

This owner’s manual contains important information regarding the instrument’s usage and operation.

Please read all chapters carefully, keeping this manual handy for future reference.



About this Owner’s Manual

Before attempting to play this instrument, please read the Introduction chapter from page 10 of this owner’s manual. This chapter provides a brief explanation of each section of the MP7SE’s control panel, an overview of its various jacks and connectors, and details how the components of the instrument’s sound are structured.

The Main Operation chapter (page 20) provides an overview of the instrument’s most commonly used functions, beginning with turning zones on and o, adjusting their volume, and selecting sounds. Later on, this chapter introduces basic sound adjustment using the four control knobs, before examining how reverb, EFX, and amp simulation can all be applied to dramatically change the character of the selected sound. Next, the MP7SE’s authentic Tonewheel Organ mode is outlined, explaining how to adjust drawbar positions using zone faders and control knobs, and change the organ’s percussion characteristics. The chapter closes with an explanation of the instrument’s global EQ and transpose functions.

The EDIT Menu chapter (page 38) lists all available INT mode and EXT mode parameters by category for convenient reference. The STORE Button & SETUP Menus chapter (page 64) outlines storing customised sounds, capturing the entire panel conguration as a SETUP, then recalling dierent SETUPs from the MP7SE’s internal memory.

The Recorder chapter (page 68) provides instructions on how to record and play back pieces stored both in the instrument’s internal memory, and also MP3/WAV audio les saved to USB memory devices. This chapter also explains the MP7SE’s metronome/ drum pattern functions. Additional USB functions are covered in greater detail in the USB Menu chapter (page 99), while the SYSTEM Menu chapter (page 105) explains the MP7SE’s system settings and various reset functions.

Finally, the Appendix section (page 119) includes USB-MIDI driver information, software update instructions and listings of the instrument’s internal sounds, drum rhythms, eects, MIDI reference information, and full specication details.

WARNING

Indicates a potential hazard that could result in death or serious injury if the product is handled incorrectly.

Do not insert or disconnect the power cord plug with wet hands.

Doing so may cause electric shock.

GROUNDING INSTRUCTIONS This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualied electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product - if it will not t the outlet, have a proper outlet installed by a qualied electrician.

When using electrical products, the following basic precautions should always be followed:

The product should be connected to an AC outlet of the specied voltage.

● If you are going to use an AC power cord, make sure that its has the correct plug shape and conforms to the specied power voltage.

● Failure to do so may result in re.

120V 240V230V

The product is not completely disconnected from the power supply even when the power switch is turned o. If the product will not be used for a long time, unplug the AC power cord from the AC outlet.

● Failure to do so may cause re in case of lightning.

● Failure to do so may over-heat the product, resulting in re.

When disconnecting the AC power cord's plug, always hold the plug and pull it to remove it.

● Pulling the AC power cord itself may damage the cord, causing a re, electric shock or short-circuit.

When using the headphones, do not listen for long periods of time at high volume levels.

Doing so may result in hearing problems.

It is good practice to place the instrument near the AC outlet and the power cord plug in a position so that it can readily be disconnected in an emergency because electricity is always charging while the plug is in the AC outlet even in a power switch o condition.

Do not disassemble, repair or modify the product.

Doing so may result in product breakdown, electric shock or short-circuit.

Ensure that this product is connected to a socket with a protective earth connection.

Entry of water, needles or hair pins may result in breakdown or short-circuit. The product shall not be exposed to dripping or splashing. No objects lled with liquids, such as vases, shall be placed on the product.

Take care not to allow any foreign matter to enter the product.

Important Safety Instructions

SAVE THESE INSTRUCTIONS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

AVIS : RISQUE DE CHOC ELECTRIQUE

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lighting ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sucient magnitude to constitute a risk of electric shock to persons.

- NE PAS OUVRIR.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

Examples of Picture Symbols

denotes that care should be taken. The example instructs the user to take care not to allow ngers to be trapped.

denotes a prohibited operation. The example instructs that disassembly of the product is prohibited.

denotes an operation that should be carried out. The example instructs the user to remove the power cord plug from the AC outlet.

Read all the instructions before using the product.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prongs are provided for your safety. If the provided plug does not t into your outlet, consult an electrician for

1 0) Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specied by the manufacturer.

1 2) Use only with the cart, stand, tripod, bracket, or table

specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

1 3) Unplug this apparatus during lightning storms or

when unused for long periods of time.

1 4) Refer all servicing to qualied service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

replacement of the obsolete outlet.

When using electrical products, the following basic precautions should always be followed:

WARNING

The product should be connected to an AC outlet of the specied voltage.

Do not insert or disconnect the power cord plug with wet hands.

Take care not to allow any foreign matter to enter the product.

When using the headphones, do not listen for long periods of time at high volume levels.

Do not disassemble, repair or modify the product.

Indicates a potential hazard that could result in death or serious injury if the product is handled incorrectly.

120V 240V230V

● If you are going to use an AC power cord, make sure that its has the correct plug shape and conforms to the specied power voltage.

● Failure to do so may result in re.

Doing so may cause electric shock.

Doing so may result in hearing problems.

Doing so may result in product breakdown, electric shock or short-circuit.

When disconnecting the AC power cord's plug, always hold the plug and pull it to remove it.

● Pulling the AC power cord itself may damage the cord, causing a re, electric shock or short-circuit.

● Failure to do so may cause re in case of lightning.

● Failure to do so may over-heat the product, resulting in re.

Ensure that this product is connected to a socket with a protective earth connection.

Indicates a potential hazard that could result in injury or

CAUTION

Do not use the product in the following areas.

● Areas, such as those near windows, where the product is exposed to direct sunlight

● Extremely hot areas, such as near a heater

● Extremely cold areas, such as outside

● Extremely humid areas

● Areas where a large amount of sand or dust is present

● Areas where the product is exposed to excessive

vibrations

damage to the product or other property if the product is handled incorrectly.

Using the product in such areas may result in product breakdown. Use the product only in moderate climates (not in tropical climates).

Before connecting cords, make sure that the power to this product and other devices is turned OFF.

Do not drag the product on the oor. Take care not to drop the product.

Do not place the product near electrical appliances such as TVs and radios.

When connecting the AC power cord and other cords, take care not to get them tangled.

Do not wipe the product with benzene or thinner.

Do not stand on the product or exert excessive force.

OFF

Failure to do so may cause breakdown of this product and other devices.

Please lift up the product when moving it. Please note that the product is heavy and must be carried by more than two persons. Dropping the product may result in breakdown.

● Doing so may cause the product to generate noise.

● If the product generates noise, move the product suciently away from the electrical appliance or connect it to another AC outlet.

Failure to do so may damage them, resulting in re, electric shock or short-circuit.

● Doing so may result in discoloration or deformation of the product.

● When cleaning the product, put a soft cloth in lukewarm water, squeeze it well, then wipe the product.

● Doing so may cause the product to become deformed or fall over, resulting in breakdown or injury.

Do not place naked ame, such as lighted candles on the product.

Ensure that the ventilation is not impeded by covering the ventilation openings with items, such as newspaper, table-cloths, curtains, etc.

The product should be located so that its location or position does not interfere with its proper ventilation. Ensure a minimum distance of 5cm around the product for sucient ventilation.

Doing so may cause the illumination to fall over, resulting in re.

Failure to do so may over-heat the product, resulting in re.

The product should be serviced by qualied service personnel when:

• The power supply cord or the plug has been damaged.

• Objects have fallen, or liquid has been spilled into the product.

• The product has been exposed to rain.

• The product does not appear to operate normally or exhibits a marked change in performance.

• The product has been dropped, or the enclosure damaged.

Notes on Repair

Should an abnormality occur in the product, immediately turn the power OFF, disconnect the power cord plug, and then contact the shop from which the product was purchased.

Instruction for AC power cord (U.K.)

WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

• GREEN-AND-YELLOW: EARTH

• BLUE: NEUTRAL

• BROWN: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.

• The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.

• The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.

• The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

An information on Disposal for users

If your product is marked with this recycling symbol it means that, at the end of its life, you must dispose of it separately by taking it to an appropriate collection point. You should not mix it with general household waste. Disposing of this product correctly will prevent potential negative eects on the environment and human health which could otherwise arise due to inappropriate waste handling. For further details, please contact your local authority. (European Union only)

FCC Information (U.S.A)

CAUTION: Changes or modications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Declaration of Conformity

Products: Model Number: Responsible Party Name: Address: Telephone:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Electronic Piano MP7SE Kawai America Corporation 2055 East University Drive, Rancho Dominguez, CA 90220 310-631-1771

This applies only to products distributed by Kawai America Corporation.

Important Safety Instructions ...................4

Table of Contents ................................8

Introduction

Welcome to the MP7SE .........................10

1. Feature Highlights ..............................10

2. Owner’s Manual Conventions ..................11

Part Names & Functions ........................12

1. Front Panel: Knobs, Faders & Buttons ...........12

2. Front Panel: Jacks & Connectors ................16

3. Rear Panel: Jacks & Connectors .................16

Connecting to Other Devices ..................18

Understanding the MP7SE .....................19

Main Operation

Getting Started .................................20

Selecting Sounds ...............................21

Zone Functions .................................22

1. Zone Basics .....................................22

2. Zone Modes

3. Zone Key Range ................................24

(int/ext/both) .........................23

EDIT Menu

Overview of the EDIT Menu (INT mode) ............38

EDIT Menu parameters (INT mode) ................40

1. Reverb ..........................................40

2.1. EF X ............................................40

2.2. Amp Simulator

3. Sound ..........................................42

4. Tuning ..........................................45

5. Key Setup .......................................46

6. Controllers ......................................49

7. Knob Assign ....................................51

8. Virtual Technician

Virtual Technician

Overview of the EDIT Menu (EXT mode) ...........54

EDIT Menu parameters (EXT mode) ................56

1. Channel/Program ...............................56

2. SETUP ..........................................56

3. Transmit

4. MMC

5. Key Setup .......................................58

.......................................57

(MAIN zone) ......................41

(PIANO sounds) ..................52

(E.PIANO, HAR PSICHORD, BASS sounds) ...53

(DRAWBAR sounds) .................53

....................................57

LCD Display & Control Knobs ...................26

Eects Section ..................................27

1. Reverb ..........................................27

2. EFX .............................................28

3. Amp Simulator

(MAIN zone only) ....................30

Tonewheel Organ Mode ........................32

Global Section ..................................34

1. EQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

2. Transpose .......................................36

3. Local O ........................................37

6. Controllers ......................................60

7. Knob Assign ....................................62

Overview of the EDIT Menu (BOTH mode) ..........63

STORE Button & SETUPs

Overview of the STORE Button .................64

1. Storing a SOUND ...............................64

2. Storing a SETUP .................................65

3. Storing POWERON settings .....................66

SETUP Memories ...............................67

Recorder

SYSTEM Menu

Overview of the Recorder ......................68

Song Recorder (Internal memory) ....................69

1. Recording a song ...............................69

2. Playing back a song. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

3. Saving a song as an SMF le ....................73

4. Loading an SMF le into memory .............. 74

5. Erasing a song ..................................77

6. Song Transpose .................................78

7. Panel Mode .....................................78

8. MIDI to Audio ...................................78

9. SMF Direct Play .................................79

SMF Mixer .......................................80

Audio Record/Playback (USB memory) ..............81

1. Recording an audio le .........................81

Overview of the SYSTEM Menu ...............105

SYSTEM Menu Parameters & Functions .......106

1. Utility ..........................................106

2. Pedal/Mod. ....................................108

Expression pedal calibration ...................109

3. MIDI ...........................................110

4. Oset ..........................................111

5. User Edit .......................................111

Creating a User Touch Curve ................... 112

Creating a User Temperament .................113

Creating a User Key Volume ...................114

Creating a User Stretch Tuning .................115

Creating a User Voicing ........................116

6. Reset ...........................................117

2. Playing an audio le ............................84

3. Overdubbing an audio le ......................87

4. MIDI to Audio ...................................90

Metronome .....................................93

1. Click mode ......................................93

2. Rhythm mode ..................................94

3. Recording with the metronome ................97

USB Menu

Overview of the USB Menu .....................99

USB Menu Functions ..........................100

1. Load ...........................................100

2. Save ...........................................101

3. Delete .........................................102

4. Rename ........................................103

Panic button ...................................117

Panel Lock ( ) .................................118

Appendix

Troubleshooting ...............................119

USB MIDI (USB to Host connector) .....................124

Software Update ..............................12 5

Sound List .....................................126

Rhythm Pattern List ...........................127

EFX Categories, Types, & Parameters .........12 8

Specications ..................................133

MIDI Implementation .........................134

1. Recognised Data ...............................135

2. Transmitted Data ..............................139

3. Exclusive Data .................................141

4. SOUND/SETUP Program/Bank .................153

5. Program Change Number List .................154

6. Control Change Number (CC#) Table ..........157

MIDI Implementation Chart ......................158

Welcome to the MP7SE

Feature Highlights

‘Responsive Hammer III’ weighted-key action, with Ivory Touch key surfaces and Let-o simulation

The MP7SE’s Responsive Hammer III (RH III) keyboard action recreates the distinctive touch of an acoustic grand piano, with its realistic movement and accurate 3-sensor technology providing a smooth, natural, and highly responsive piano playing experience. The weight of the keyboard is appropriately graded to mirror the heavier bass hammers and lighter treble hammers of an acoustic piano, while structural reinforcements within the action assembly ensure greater stability during fortissimo and staccato passages.

Introduction

The RH III keyboard action also reproduces the subtle let-o sensation felt when playing the keys of a grand piano very softly, enhancing delicate pianissimo playing to satisfy the expectations of even the most discerning pianists. Finally, the MP7SE keyboard action features Kawai’s Ivo r y Tou ch key surfaces as standard. This nely textured material gently absorbs moisture to assist playing control, and possesses a natural, matte nish that is smooth, but not slippery.

The ultimate pianos for Concert, Pop, and Jazz

The MP7SE captures the beautiful sound of Kawai’s SK-EX, EX, and SK-5 acoustic grand pianos, with all 88 keys of these exceptional instruments meticulously recorded, analysed and faithfully reproduced using proprietary Harmonic Imaging™ technology. This unique process accurately recreates the broad dynamic range of the original grand pianos, aording pianists an extraordinary level of expressiveness ranging from the softest pianissimo to the strongest, boldest fortissimo.

With separate categories for Concert, Pop, and Jazz playing, the MP7SE oers an excellent selection of high quality acoustic piano sounds suitable for various musical styles, including separate sub-categories for upright and mono pianos.

Moreover, Kawai’s unique Virtual Technician feature allows various characteristics of the selected acoustic piano sound to be shaped at the touch of a button or the turn of a knob, with parameters to adjust voicing and regulation, string and damper resonances, and subtle hammer, damper, and key release noises.

Vintage EPs, twin eects, and amp simulation

The MP7SE also features an excellent selection of vintage electric piano sounds, each with their own distinctive characteristics. Enjoy their natural, organic sound, or pass the signal through a wide variety of classic eects stomp boxes, before plugging into one of the ve classic amp and speaker cabinets – complete with realistic microphone character and position modelling.

Classic tonewheel organs with drawbar control and authentic percussion

The MP7SE’s brand new tonewheel organ simulation transforms the stage piano into a vintage electromechanical organ, complete with nine real-time adjustable drawbars and authentic percussion controls. Organ enthusiasts can dial-in favourite drawbar registrations, adjust the ‘condition’ of the organ tone, and select their preferred rotary speaker character, then store the sound to memory for immediate recall. With organ mode selected, the MP7SE adjusts the strike point for the keyboard, allowing blazing runs and greasy licks to be played on its fully-weighted action as easily as the real thing.

High quality strings, pads, brasses, basses and more

Supplementing the realistic acoustic pianos, vintage electric pianos, and growling tonewheel organs, the MP7SE features a broad range of high quality strings, pads, synths, brass and woodwind voices, basses, guitars, and a whole host of other useful sounds. These supplementary sounds are ideal for building layers, adding texture to other instruments, or for playing individually, at the front of the mix. And if the stock sound isn’t quite perfect, feel free to customise and tweak using the MP7SE’s exible ADSR parameters and resonance/cut-o controls – all immediately accessible directly from the panel.

Four zone master keyboard controller

The MP7SE maintains the MP series’ classic four-zone approach, with each zone able to play internal sounds, external MIDI devices, or both types simultaneously. Zones can be played individually, or freely split, layered and velocity switched to create stunning personalised performances. The MP7SE’s powerful customisation allows parameters and settings for each zone to be adjusted and controlled independently, making for an unbelievably versatile all-in-one performance instrument.

Intuitive operation, large LCD, real-time assignable control knobs

The MP7SE’s control panel is clearly arranged and easy to use, with related functions grouped together and placed where you’d expect to nd them. A large LCD display and four assignable control knobs, allow several parameters to be adjusted directly in real-time, without getting lost in menus – concentrate on playing, rather than trying to remember which button does what.

256 Setup memories: enough for the busiest stage musician

The MP7SE allows every single customised sound, knob position, fader level, and adjustable parameter to be stored in memory as

a SETUP, and recalled at the touch of a button. With over 250 SETUP memories, the MP7SE is ideal for busy stage musicians who

like to plan several shows ahead, before going out on the road.

USB to Device functionality, with MP3/WAV/SMF le recording and playback

The MP7SE is equipped with USB connectors that not only allow the instrument to be connected to a computer for MIDI use,

but also to load and save data to USB memory devices directly. This ‘USB to Device’ feature allows customised sounds, SETUP

memories, and recorder songs stored in internal memory to be saved to USB for posterity.

USB memory devices can also be used to play back MP3 or WAV audio or SMF MIDI les, allowing performing musicians to

play along with professional backing tracks, or simply learn the chords or melody for a new piece. It is even possible to save

performances directly as MP3, WAV, or SMF les for emailing to band members, casual listening away from the keyboard, or fur ther

editing using an audio workstation.

Owner’s Manual Conventions

This owner’s manual utilises a number of illustrative conventions in order to explain the MP7SE’s various functions.

The examples below provide an overview of the button LED indicator states and press types, and the appearance of

dierence kinds of explanation text.

Button LED indicator states



LED indicator OFF:

Sound/Function is not selected.

LED indicator ON:

Sound/Function is selected.

LED indicator ashing:

Sound/Function is selected in a temporary state.

Introduction

Button press types



Normal press:

Select a sound or function, or turn a function ON/OFF.

Text appearance



Normal instruction and explanation text is written in regular type at 9 pt. size.

Captions explaining the LCD display or button functions, are written in bold type at 8.5 pt. size.

hold

Press and hold:

Show a function’s parameters.

* Notes about functions are marked with an

asterisk and written in 7.5 pt. size.

Example operations are written in italic type at 8 pt. size, and enclosed within a grey box.

hold

Press and hold, then press X:

Set split points, create zone ranges, set transpose key, etc.

Reminders, hints, and additional explanations are written in italic type at 9 pt. size.

Part Names & Functions

Introduction

Front Panel: Knobs, Faders & Buttons

Control Wheels

PITCH BEND wheel

This control wheel smoothly bends the pitch up or down from its current value.

ASSIGN Buttons

Volume Faders

MODULATION wheel

This control wheel controls the modulation (vibrato) depth. Moving the wheel forward increases the vibrato depth. The LED indicator will turn ON when this wheel is in use.

* Alternative functions can be assigned to the MODUL ATION wheel in the

Controllers page of the EDIT menu (page 49).

SW1 / SW2 buttons

These buttons turn user-assigned functions ON or OFF. Various dierent functions can be assigned to these buttons, allowing immediate control during performances.

* Press and hold either button to show the respective assign parameters of

the EDIT menu in the LCD display.

* For more information about assigning functions, please refer to page 49.

MASTER VOLUME fader

This fader controls the volume level of the MP7SE’s OUTPUT and HEADPHONE jacks.

LINE IN fader

This fader controls the LINE IN volume level.

* The LINE IN volume level can be further adjusted by using the Input Level

parameter in the Utility page of the SYSTEM menu. For more information, please refer to page 107.

MIXER Section

Introduction

VOLUME faders

These faders control the individual volume levels of the MAIN, SUB1, SUB2, and SUB3 zones. When multiple zones are active, these faders can be used as an audio mixer.

When the tonewheel organ mode is selected, these faders are used to adjust the position of the assigned drawbars.

INT/ E XT LE Ds

These LEDs indicate whether a zone is controlling an internal sound, an external MIDI device, or both simultaneously.

ZONE ON/OFF buttons

These buttons turn the MAIN, SUB1, SUB2, and SUB3 zones ON or OFF.

When the tonewheel organ mode is selected, these buttons are used to change the percussion characteristics of the organ.

* When the key range is set, the LED indicator for the zone button will also

turn green.

* Press and hold each zone button to show the respective key range setting

pop-up in the LCD display.

GLOBAL Section

EQ button

This button turns the global EQ ON or OFF.

* Press and hold this button to show the EQ settings in the LCD display.

TRANSPOSE button

This button turns the TRANSPOSE function ON or OFF.

* Press and hold this button to show the transpose settings pop-up in the

LCD display.

LOCAL OFF

This button disables the internal connection between the MP7SE’s keyboard and tone generators.

Part Names & Functions

EFFECTS Section

EFX1/EFX2/EFX buttons

These buttons turn the eects for each zone ON or OFF. The MAIN zone has two eect modules, while the SUB1, SUB2, and SUB3 zones have one eect module each.

AMP button

This button turns the amp simulator for the MAIN zone ON or OFF.

Introduction

* Press and hold each button to show the respective settings pages of the

EDIT menu in the LCD display.

DISPLAY Section

EDIT Section

REVERB buttons

These buttons turn the reverb for each zone ON or OFF.

LCD Display

The LCD display provides a visual indication of the selected zone and sound, parameter values, and the status of other functions when active.

A/B/C/D control knobs

These knobs adjust displayed parameter values in real-time.

* EDIT menu parameters can be freely assigned to each of the four knobs in

the Knob Assign page of the EDIT menu (page 51).

F1/F2/F3/F4 buttons

These buttons select the four zones (MAIN, SUB1, SUB2, SUB3) to be displayed and controlled. In other modes (e.g. Recorder) these buttons also select additional functions.

INT / MIDI button

This button is used in conjunction with the +/YES or –/NO buttons to change the zone mode (INT, EXT, or BOTH).

LOCK ( ) button

This button locks the MP7SE’s control panel, thus preventing any accidental button pushes during a performance.

STORE button

This button stores edited SOUNDS, or full panel settings to the SETUP and POWERON memories.

EXIT button

This button exits the current mode or page.

EDIT button

This button enters the EDIT menu. When the EDIT menu is displayed, this button also enters the selected parameter category page.

CURSOR buttons

These buttons move the selection cursor and scroll through the various pages of the EDIT menu.

– / NO + / YES buttons

These buttons decrease or increase the value of the selected parameter, and also cancel or conrm operations that require user interaction (e.g. Erasing data).

SOUND / SETUP Section

RECORDER Section

SOUND button

This button sets the MP7SE to SOUND mode, whereby the buttons on the right will select the instrument’s 256 internal sounds.

SETUP button

This button sets the MP7SE to SETUP mode, whereby the buttons on the right will select the instrument’s 256 SETUP memories.

* Press this button while in SETUP mode to show the SETUP summary pop-

up in the LCD display.

SOUND/SETUP SELECTION buttons

In SOUND mode, these buttons select the category, type, and variation of the zone’s sound. In SETUP mode, these buttons select the bank and memory used for the SETUP.

ON/OFF button

This button turns the RECORDER section ON or OFF.

Introduction

SETTING Section

METRONOME button

This button activates the METRONOME or RHYTHM patterns.

(RESET) button

This button resets the MP7SE’s song recorder, rewinding songs and MP3/WAV/SMF les to the beginning.

(RECORD) and (PL AY/STO P) but to ns

These buttons record and playback/stop songs stored in the MP7SE’s internal memory, or MP3/WAV les saved to a USB memory device.

(LOOP) button

This button activates the MP7SE’s A-B Loop function, allowing passages of a recorder song or MP3/WAV/SMF le to be played back repeatedly.

(REW) and (FWD) buttons

These buttons are used to move the playing position of the current recorder song or MP3/WAV/SMF backward or forward.

PANIC button

This button returns the MP7SE to the Power On state, and also sends All Note O and Reset All Controller messages via MIDI.

SYSTEM button

This button enters the SYSTEM menu, allowing many aspects of the MP7SE’s functionality to be adjusted.

USB button

This button enters the USB menu, allowing data to be loaded and saved from/to a connected USB memory device.

Part Names & Functions

Front Panel: Jacks & Connectors

Introduction

Rear Panel: Jacks & Connectors

HEADPHONE jack

The headphone jack is located at the left end of the key slip and used to connect a pair of headphones equipped with a standard 1/4” phone jack.

USB TO DEVICE port

The USB to Device port is located at the right end of the key block and used to connect a FAT or FAT32 formatted USB memory device to load and save data.

* Please note that wireless ash memory devices are not compatible with

the MP7SE.

POWER Section

MIDI Section

* The instrument’s USB MIDI port and MIDI IN/OUT jacks can be connected

and used simultaneously. To adjust MIDI routing, please refer to the MIDI parameters in the SYSTEM menu, explained on page 110.

AC IN

Connect the power cable included with the MP7SE to this receptacle.

POWER SWITCH

This switch turns the MP7SE ON and OFF.

* The MP7SE features a power saving mode that can turn o the instrument

automatically after a specied period of inactivit y. For more information, please refer to page 107.

MIDI THRU/OUT/IN jacks

These jacks are used to connect the MP7SE to external MIDI devices, and also to a computer with a MIDI interface as an alternative to the ‘USB to Host’ port.

USB TO HOST port

This port is used to connect the MP7SE to a computer using a USB cable. When connected, the instrument can be used as a standard MIDI device, allowing it to send a receive MIDI data. Connect a ‘B’ type USB connector to the instrument, and an ‘A’ type USB connector to the computer.

* When connecting the MP7SE to a computer using the ‘USB to Host ’ port,

additional driver software may be required. For more information, please refer to page 124.

FOOT CONTROLLER Section

EXP TYPE switch

This switch is used to select the EXP pedal’s TRS connector type.

EXP jack

This jack is used to connect an expression pedal to the MP7SE.

* For information about calibrating the expression pedal to ensure correct

operation with the MP7SE, please refer to page 109.

FSW jack

This jack is used to connect a momentary foot switch pedal to

Expression

EXP type Description

RING (NOR) TRS plug’s Ring to WIPER

TIP TRS plug’s Tip to WIPER

* Functions can be freely assigned to each foot controller in the Controllers

page of the EDIT menu. For more information, please refer to page 49.

* For more information about purchasing the GFP-3 triple pedal accessory,

please contact your local Kawai distributor.



Kawai GFP-3 triple pedal accessory: default pedal assignments

Left pedal:

Soft

FSW

F10-H

GFP-3

Right pedal:

Damper

the MP7SE.

* If the foot switch pedal is not turned o when releasing it, check the FSW

polarity. Please refer to page 108.

DAMPER (F-10H) jack

This jack is used to connect the included F-10H damper pedal to the MP7SE.

GFP-3 jack

This jack is used to connect the optional Kawai GFP-3 triple pedal accessory to the MP7SE.

By default, with the optional GFP-3 triple pedal unit connected, the right pedal acts as a damper pedal, the centre pedal acts as a sostenuto pedal, and the left pedal functions as a soft pedal.

* Functions can be freely assigned to each foot controller in the Controllers

page of the EDIT menu. For more information, please refer to page 49.

Introduction

Centre pedal:

Sostenuto

OUTPUT Section

INPUT Section

OUTPUT jacks

These jacks are used to connect the MP7SE to a musical instrument amplier, PA system, or recording console using standard 1/4” phone jacks. To output a mono signal, connect the cable to the L/MONO jack.

INPUT jacks

These jacks are used to connect a pair of stereo outputs from other electronic instruments or audio equipment to the MP7SE. The input level can be easily adjusted using the LINE IN fader. When connecting a mono audio source, connect the cable to the L/MONO jack only.

* When using the Audio Recorder function, the INPUT audio will also be recorded

to the WAV/MP3 le. For more informati on, please refer to page 81.

Connecting to Other Devices

Introduction

Control external MIDI devices, or connect to a computer with a MIDI interface.

Connect an expression pedal. Set the correct EXP TYPE.

Connect the included F-10H damper pedal.

Connect the stereo output from tablets, portable audio devices or other electronic instruments.

USB type ‘B’

USB type ‘A’

Connect to a computer to exchange MIDI data and use DAW software.

Connect a footswitch pedal.

Connect the GFP-3 triple pedal unit accessory.

Connect to ampliers, speakers, etc.

Understanding the MP7SE



Preparation before use

The MP7SE does not feature built-in speakers. Therefore, in order to listen to the MP7SE, it will rst be necessary to connect a mixer, keyboard amplier, or headphones to the instrument.

Once connected to an audio output device, press the POWER SWITCH located on the right of the rear panel to turn on the MP7SE. It is recommended to turn on the MP7SE before the audio output device in order to avoid the unpleasant switching noise that can sometimes occur.



MP7SE zone structure: explanation

The MP7SE features 4 zones: MAIN, SUB1, SUB2, and SUB3. Each zone features a dedicated VOLUME fader and can be turn ed ON or OFF freely. Zones can be set to INT (play the MP7SE’s internal sounds), EXT (control external MIDI devices) or INT and EXT simultaneously.

When a zone is set to INT, the process of selecting and assigning sounds is largely identical for each zone. However, there are some important dierences between the MAIN zone and three SUB zones. First, the MAIN zone features two separate EFX modules and an additional AMP simulator, while the SUB zones each feature one EFX module only. Moreover, the MAIN zone allows any of the 129 eects to be assigned to both EFX modules, however the variety of eects available to the SUB zones’ EFX modules is limited to 22 eects. Finally, the MP7SE’s tonewheel organ mode can only be used with the MAIN zone is selected, thus the SUB zones are limited to using the standard PCM organ sounds. All sounds are adjusted using the various parameters in the EDIT menu, with additional ‘Feature Parameters’ that are specic to certain sounds.

Introduction

REVERB settings are common for all zones, however the depth parameter can be controlled independently for each zone. The MP7SE’s EQ is also common for all zones, however parameters in the EDIT menu allow the tonal character for each zone’s sound to be adjusted independently.

When set to EXT, zones are used to control external MIDI devices. The MAIN and SUB zones share the same MIDI capabilities, allowing up to four MIDI channels to be independently controlled at the same time. As with INT mode, various parameters to dene transmit/ receive channels, MMC features, keyboard ranges, and knob assignments can be accessed for each EXT zone via the EDIT menu.

Modications to each sound can be stored as individual SOUND presets, while the entire conguration of the MP7SE itself can be stored in one of the 256 SETUP memories.



MP7SE zone structure: block diagram

The diagram below illustrates the zone structure of the MP7SE.

Line In

MAIN

SUB1

SUB2

SUB3

Line In Fader Input Level

Zone Mode

INT

EXT

MAIN Fader

INT

EXT

SUB1 Fader

INT

EXT

SUB2 Fader

INT

EXT

SUB3 Fader

Noise Gate

EFX1Amp EFX2

EFX

MAIN Reverb Depth

SUB1 Reverb Depth

SUB2 Reverb Depth

SUB3 Reverb Depth

Virtual Technician

Master Fader

Normal Out

Reverb

Key MIDI

MIDI Out

Key USB

USB-MIDI Out

Getting Started

After connecting the power cable, speakers/headphones, and pedals, it’s time to start playing the MP7SE stage

piano. This page will explain how to turn on the instrument, set the MAIN zone volume, and adjust the master

volume.

1. Turning the MP7SE ON

Press the POWER SWITCH.

The instrument will turn ON, and after a brief period the main Play Mode screen will be shown in the LCD display.

Main Operation

* For more information about the play screen, please refer to page 26.

* The MP7SE features a power saving mode that can turn o the instrument

automatically after a specied period of inactivit y. For more information, please refer to page 107.

2. Adjusting the MAIN zone volume

Move the MAIN zone volume fader to the top-most position.

* For more information about adjusting the volume of zones, please refer

to page 22.

4. Playing the piano

Start playing the piano.

The rich sound of a Kawai SK-EX Concert Grand Piano will be heard as the keys are pressed.

3. Adjusting the MP7SE’s master volume

Move the MASTER VOLUME fader to the half-way position.

If necessary, increase or decrease the MASTER VOLUME fader to nd a comfortable listening level.

Selecting Sounds

The MP7SE stage piano features a wide selection of realistic instrument sounds suitable for various musical styles

Sounds are arranged into eight categories, with eight further sub-categories, and four variations, providing a total

of 256 dierent instrument sounds. For a complete listing of the available instrument sounds, please refer to page

126 of this owner’s manual.

* The example below will explain how to select the ‘60’s EP 2’ electric piano sound, however the process is identical for all other sounds.

1. Selecting the sound category

Press the desired sound category button from the top row of sound buttons.

The LED indicator for the button will turn ON to indicate that the category is selected, and a sound variation pop-up list will briey be shown in the LCD display.

LED indicator ON:

Category is selected

2. Selecting the sound sub-category

Press the desired sound sub-category button from the middle row of sound buttons.

The LED indicator for the button will turn ON to indicate that the sub-category is selected, and a sound variation pop-up list will briey be shown in the LCD display.

3. Selecting the sound variation

Press the desired sound variation button from the bottom row of sound buttons.

Example: To select the Electric Piano sound category, press the E.PIANO button.

LED indicator ON:

Sub-category is selected

Example: To select the third sub-category of electric pianos, press the ‘3’ sub-category button.

Main Operation

The LED indicator for the button will turn ON to indicate that the variation is selected, and a sound variation pop-up list will briey be shown in the LCD display.

* Sounds can be selected by pressing the categor y, sub-category, and

variation buttons in any order.

* When selecting a dierent sound category, the previously selected sub-

category and variation will be recalled automatically.

LED indicator ON:

Sound variation is selected

Example: To select the ‘60’s EP 2’ sound, press the ‘B’ sound variation button.

Zone Functions

Zone Basics

As noted in the Introduction chapter, the MP7SE features four zones: MAIN, SUB1, SUB2, and SUB3. This page will

explain the process for turning zones ON and OFF, adjusting zone volumes, and creating a simple two zone layer.



Turning a zone ON or OFF

Press the button corresponding to the desired zone to turn that zone ON or OFF.

The LED indicator for the pressed zone button will turn ON or OFF to indicate the current status of the zone.

If a zone is turned OFF but then selected, a added to the left of the sound name in the LCD display.

Zone is

Main Operation

turned OFF

LED indicator ON:

Zone is turned ON

symbol will be

* When a zone is turned OFF, information for the previously selected (or

neighbouring) zone will be shown in the LCD display.

* When Receive Mode (page 110) is set to ‘Multi’, the MIDI input signal will

still trigger sounds even when a zone is turned OFF.



Adjusting the zone volume

Use the VOLUME fader above each zone button to adjust the volume of that zone.

The volume of the zone will increase or decrease independently of the other zones.

* When playing with just a single zone (e.g. MAIN), it is recommended to set

the volume fader to the maximum position and use the MASTER volume

fader to adjust the overal volume of the instrument.

To adjust the volume of all sound sections simultaneously, use the MASTER VOLUME fader (page 12).



Creating a simple two zone layer

First, turn the MAIN zone ON, then select a piano sound.

Increase

volume

Decrease

volume

* When tonew heel organ mode is sel ected and the soun d edit screen shown

in the LCD display, these VOLUME faders are used to adjust the drawbar positions of the organ. For more information please refer to page 32.

Next, turn the SUB1 zone ON, and select a strings sound.

Play the layered piano and strings sound, adjusting the MAIN and SUB1 volume faders to set the level of each sound.

Zone Modes (int/ext/both)

Also noted in the introduction, the MP7SE’s four zones can each be set to control the instrument’s internal sounds

(INT), external MIDI devices (EXT), or both internal and external simultaneously (BOTH). This page will outline the

dierences between the zone modes, and explain how to switch between them.



Zone modes

Zone mode Description Panel Appearance

INT The zone will control internal sounds only.

EXT The zone will control external MIDI devices only.

BOTH The zone will control both internal sounds and external MIDI devices simultaneously.



Selecting zones

Press the F1~F4 function buttons located below the LCD display to select the desired zone.

Main Operation

The selected zone will be shown in the LCD display.

SUB2 zone selected



Changing the zone mode

Press and hold the INT/MIDI button, then press the +/YES or –/ NO buttons to cycle through the dierent zone modes.

The LED indicator for the zone will change to indicate the selected zone mode, and the Zone Mode pop-up will briey be shown in the LCD display.

Before:

EXT mode

Zone LED

Example: To select the SUB2 zone, press the F3 function button.

hold

× 2

After:

INT mode

* By default , the MAIN and SUB1 zones will be set to INT mode, and the SUB2

and SUB3 zones will be set to EXT mode.

Zone LED

Example: To change the SUB2 zone from EXT mode to INT mode, press and hold the INT/MIDI button, then press the +/YES button twice.

Zone Functions

Zone Key Range

By default, the four zones will each utilise all 88-key of the MP7SE’s keyboard. However, by using the Key Range

function it is possible to create custom keyboard ranges (between two dened keys) for each zone, allowing a

selection of internal sounds or external MIDI devices to be controlled by dierent parts of the keyboard.

* The example below will explain how to specify key ranges for just the MAIN and SUB1 zones (with a piano sound and acoustic bass sound assigned to the

two zones), however the process is identical for all four zones.

1. Selecting sounds for the MAIN and SUB1 zones

First, turn the MAIN zone ON, then select a piano sound.

Main Operation

Next, turn the SUB1 zone ON, and select a bass sound.

Play the piano.

The piano sound will be layered with the bass sound because both the MAIN and SUB1 zones are set to use the full keyboard.

The next step is to specify key ranges for the two zones, allowing the piano and bass sounds to be played independently.



Checking the zone key range

Press and hold the MAIN button.

The current key range for the MAIN zone will be shown in the LCD display.

Next, press and hold the SUB1 button.

The current key range for the SUB1 zone will be shown in the LCD display.

hold

2. Setting the MAIN zone key range

Press and hold the MAIN button, then press the desired low key, followed by the desired high key for the zone.

The names of the pressed low and high keys will be shown in the LCD display, and will become the new key range for the MAIN zone.

Low key:

C#3

hold

Zone key range

High key:

The LED indicator for the MAIN button will also turn green to indicate that a key range has been set.

3. Setting the SUB1 zone key range

Press and hold the SUB1 button, then press the desired low key, followed by the desired high key for the zone.

The names of the pressed low and high keys will be shown in the LCD display, and will become the new key range for the SUB1 zone.

Low key:

Low key: C#3

Example: To set the MAIN zone key range between ke y C#3 and C8, press and hold the MAIN zone button, then press the C#3 key, followed by the C8 key.

* It is also possible to set the zone key range using the KeySetup parameters

in the EDIT menu. For more information, please refer to page 47.

hold

Zone key range

High key: C8

Main Operation

High key:

Low key: A0 High key: C3

Example: To set the SUB1 zone key range between key A0 and C3, press and hold the SUB1 zone button, then press the A0 key, followed by the C3 key.

The LED indicator for the SUB1 button will also turn green to indicate that a key range has been set.

* It is also possible to set the zone key range using the KeySetup parameters

in the EDIT menu. For more information, please refer to page 47.

4. Playing the MAIN and SUB1 zone key ranges

Test the new zone key ranges by playing a chromatic scale from the bottom-most note of the keyboard. The bass sound will be heard from the bottom-most key to the C3 key, and the piano sound will be heard from the C#3 key to the top-most key. This bass/piano conguration is a popular combination for playing jazz standards.

LCD Display & Control Knobs

In regular Play Mode the LCD display provides a visual indication of the selected zone and sound, and the values of

the four real-time control knobs (A, B, C, and D).

The function of each knob can be assigned to control any parameter in the EDIT menu, allowing frequently used

functions to be accessed from a single screen. Furthermore, two groups of knob parameters (2 x 4) can be dened

for each of the MAIN, SUB1, SUB2, and SUB3 zones, providing extensive real-time control.

Selected sound

Control knobs:

Adjust value of assigned

parameters or settings.

Main Operation

Function buttons:

Select zone and various

other operations.



Selecting zones, primary/secondary knob groups

Press the F1~F4 function buttons located below the LCD display to select the desired zone.

The bottom tab representing the zone will become highlighted, and the name of the selected sound and primary group of knob parameters will be shown in the LCD display.

Press the same function button to cycle between the zones’ primary and secondary knob parameters in the LCD display.

* While in the EDIT menu, pressing the same F1~F4 FUNCTION button will

scroll through the dierent parameter pages.

Selected zone/knob group

INT/MIDI button:

Toggle between zone modes (INT/EXT/BOTH). Please refer to page 23.

Primary Secondary



Changing zones modes (INT/MIDI button)

For information about changing zone modes, please refer to page 23.



Adjusting parameters

Turn the four control knobs (A, B, C, D) located on either side of the LCD display to adjust the displayed knob group parameters.

* EDIT menu parameters can be freely assigned to each of the four knobs in

the Knob Assign page of the EDIT menu (page 51).

Parameters can also be adjusted by using the CURSOR buttons to move the selection cursor, and +/YES or –/NO buttons to increase or decrease the value of the selected parameter.

Eects Section

Reverb

Reverb adds reverberation to the sound, simulating the acoustic environment of a recital room, stage, or concert

hall. The MP7SE oers 6 types of high quality reverb, with independent ON/OFF and depth controls for each zone.

The reverb type, pre-delay, and time parameters, however, are common for all zones.

* For more information about common parameters, please refer to page 38.

Reverb types



Reverb type Description

Room Simulates the ambiance of a small rehearsal room.

Lounge Simulates the ambience of a piano lounge.

Small Hall Simulates the ambiance of a small hall.

Concert Hall Simulates the ambiance of a concert hall or theater.

Live Hall Simulates the ambiance of a live hall or stage.

Cathedral Simulates the ambiance of a large cathedral.

Main Operation



Turning reverb ON or OFF

Press the REVERB button for the desired zone to turn reverb for that zone ON or OFF.

The LED indicator for the zone’s REVERB button will turn ON or OFF to indicate the current status of the reverb.



Changing the reverb type and additional parameters

Press and hold the REVERB button for the desired zone.

The REVERB page of the zone’s EDIT menu will be shown in the LCD display.

Common

parameters:

See page 38

Turn the four control knobs (A, B, C, D) to change the reverb type and adjust additional reverb parameters.

Typ e

LED indicator ON:

Reverb is turned ON

hold

PreDelay

Press and hold the REVERB button again to exit.

Reverb parameters



Knob Parameter Description Value range

A Typ e Changes the type of environment. (see table above)

B PreDelay Adjusts the delay time before the reverberation is applied. 0 ~ 200 ms

C Time Adjusts the decay length/speed of the reverberation. 300 ms ~ 10.0 s

D Depth Adjusts the depth of the environment (amount of reverberation). 0 ~ 127

Time

Depth

(depending on type)

Eects Section

EFX

In addition to reverb, various other eects can be applied to each zone, altering the tonal character and feeling of

the selected sound. The MP7SE features 129 high quality EFX types, with eects automatically applied to some

sounds by default in order to enhance their realism.

As noted in the introduction chapter, the MAIN and SUB1/SUB2/SUB3 zones share largely the same EFX operation,

however there are some important specication and capability dierences between the two zone types.

EFX specications: MAIN and SUB1/SUB2/SUB3 zones



No. of EFX blocks 2 (applied in serial, independently adjustable) 1 each (independently adjustable)

No. of available eects 129 t ypes 22 types

Amp Simulator Yes No

Main Operation

MAIN zone SUB1/SUB2/SUB3 zones

Available eect types: MAIN vs SUB1/SUB2/SUB3 zones



EFX category M S EFX category M S EFX category M S EFX category M S

1 Chorus 8 2 7 Delay/Rev 8 2 13 Groove 4 1 19 Enhancer+ 8 -

2 Flanger 5 2 8 PitchShift 3 1 14 Misc. 2 - 20 P.S hi ft+ 6 -

3 Phaser 6 1 9 Compressor 2 1 15 Chorus+ 6 - 21 Comp+ 8 -

4 Wah 6 3 10 OverDrive 3 2 16 Phaser+ 6 - 22 OverDrive+ 8 -

5 Tremolo 6 3 11 EQ/Filter 5 2 17 Wah+ 6 - 23 Parallel 6 -

6 AutoPan 4 1 12 Rotary 5 1 18 EQ+ 8 - TOTAL 12 9 22

* The ‘+’ eects consist of the base eect plus an additional combination eect, while still using only one eect module.

* For more information about available eect categories, t ypes, and parameters, please refer to page 128.



Turning eects ON or OFF

Press the EFX button for the desired zone to turn eects for that zone ON or OFF.

The LED indicator for the zone’s EFX button will turn ON or OFF to indicate the current status of the eects.

* The MAIN zone’s EFX1 and EFX2 modules and SUB1/SUB2/SUB3 zones’ EFX

modules are turned ON and OFF in exactly the same way.

LED indicator ON:

Eects are turned ON



Changing the eect category, type and additional parameters

Press and hold the EFX button for the desired zone.

The rst EFX page of the zone’s EDIT menu will be shown in the LCD display.

Page 1/2

 arrow:

Amp Simulator (MAIN zone only)

The tonal character of an amplier or speaker cabinet is an important component of vintage electric piano sounds.

The MP7SE’s Amp Simulator function features 5 typical amplier types and a selection of adjustable parameters.

Amp types



Amp type Description

S. Case A suitcase type amplier, commonly used for vintage electric piano sounds.

M. Stack A British valve guitar amplier, known for its ‘crunchy’ tonal character.

J. Combo A popular Japanese solid-state amplier favoured for its clean, yet powerful sound.

F. Bass An American valve bass amplier that became popular for guitar, harmonica, and other instruments.

L. Cabi

Main Operation



Turning the Amp Simulator ON or OFF

A valve amplier and speaker enclosed within a wooden cabinet, originally intended for drawbar organ sounds, but also used with electric pianos to produce a distinctive ‘shimmering’ sound.

Press the MAIN zone’s AMP button to turn the amp simulator ON or OFF.

The LED indicator for the AMP button will turn ON or OFF to indicate the current status of the amp simulator.



Changing the Amp type, adjusting drive, and level parameters

Press and hold the MAIN zone’s AMP button.

The rst AMP page of the EDIT menu will be shown in the LCD display.

Page 1/3

 arrow:

Turn the control knobs (A, B, C) to change the amp type, and adjust the drive and level parameters.

* For more information about additional Amp Simulator parameters, please

refer to page 41.

* Press the F1 FUNCTION buttons (corresponding to the MAIN zone) to scroll

through the dierent AMP parameter pages.

Am p Typ e

Level

LED indicator ON:

Amp Simulator is turned ON

hold

Drive

Press and hold the AMP button again to jump to the rst AMP page of the EDIT menu, and once again to EXIT.

* Above knob assignments will change depending on AMP page displayed.

+ 130 hidden pages