JVC lt37m60bu schematic

YA360200511
SERVICE MANUAL
WIDE LCD PANEL TELEVISION
LT-37M60BU, LT-37M60BU/P, LT-37M60ZU, LT-37M60ZU
BASIC CHASSIS
FL2
TABLE OF CONTENTS
1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18
5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25
COPYRIGHT © 2005 Victor Company of Japan, Limited
No.YA360
2005/11
If you need more information on Computer and Electronic Repair, please visit these
in fact
websites to improve yourself.
http://www.fastrepairguide.com http://www.protech2u.com http://www.plasma-television-repair.com http://www.lcd-television-repair.com
Happy Repairing!!
Highly Recommended Repair Ebook:
If you’re a LCD Monitor repairer, then this is the best guide for you. Why? Because, the author revealed all his LCD Monitor Repairing secrets for you. I think, with just few Repair tips you learned from this guide you will get back your investment! Click Here to read more.
This eBook will show you how to test the electronic component correctly and accurately. Some of you may say that I don’t need this eBook because it is too simple! Do you know that, there is lots of testing electronic components secrets I have learned from this guide? Do you know how to test a‘TRIAC’ correctly and accurately? If you answer no then I guess you have to get this EBook. Click Here to read more.
Are you tired of searching the service manuals to look for the value of a burnt resistor? If the answer is YES, then this eBook is a ‘must have’ guide for you. You can save a lot of time and be able to repair customer’s Electronic equipment with burnt resistors in it. Click here to read more.
SPECIFICATION
Items Contents
Dimensions ( W × H × D ) 92.6 cm × 68.9 cm × 29.7 cm [Included stand]
92.6 cm × 63.1 cm × 10.8 cm [TV only]
Mass 26.2 kg [Included stand]
20.7 kg [TV only]
Power Input AC110V - AC240 V, 50 Hz / 60 Hz
Power Consumption 173 W (Standby: 2.6 W)
TV RF System CCIR B/G, I, D/K, L
Colour System PAL / SECAM / NTSC 3.58 / NTSC 4.43 (NTSC: EXT only).
Stereo System A2 (B/G, D/K), NICAM (B/G, I, D/K, L)
Teletext System FLOF (Fastext), TOP, WST (World Standard System)
Receiving Frequency VHF
Intermediate Frequency VIF
Colour Sub Carrier Frequency
LCD panel 37V-inch wide aspect (16 : 9)
Screen Size Diagonal : 94.0 cm (H: 82.6 cm × V: 46.1 cm) Display Pixels Horizontal : 1366 dots × Vertical : 768 dots (W-XGA)
Audio Power Output 10 W + 10 W
Speaker 6.6 cm, round type × 2 (Oblique corn) Aerial terminal (VHF/UHF) 75 unbalanced, coaxial EXT-1 / EXT-2 (Input / Output) 21-pin Euro connector (SCART socket ) × 2
EXT-3 (Input) S-Video
EXT-4 (Input) Component Video
625p / 525p / 625i / 525i
HDMI Input Video
PC (RGB) Input D-sub 15 pin × 1
Audio output 500 mV (rms), Low impedance, RCA pin jack × 2 Headphone 3.5 mm stereo mini jack × 1 Remote Control Unit RM-C1811H (AA/R6 dry cell battery × 2)
Design & specifications are subject to change without notice.
SECAM
750p / 1125i
47MHz to 470MHz
UHF
470MHz to 862MHz
CATV
116MHz to 172MHz / 220MHz to 469MHz
38.9MHz(B/G, D/K, I)
SIF
33.4MHz(5.5MHz:B/G) / 32.9MHz(6.0MHz:I) / 32.4MHz(6.5MHz:L,D/K)
PAL
4.43MHz
4.40625MHz / 4.25MHz
NTSC
3.58MHz / 4.43MHz
Mini-DIN 4 pin × 1 Y: 1 V (p-p), Positive (Negative sync provided), 75 C: 0.286 V (p-p) (Burst signal), 75
Video
1 V (p-p), Positive (Negative sync provided), 75 , RCA pin jack × 1
Audio
500 mV (rms), High impedance, RCA pin jack × 2 RCA pin jack × 3
Y : 1 V (p-p) (Sync signal: ±0.35V(p-p), 3-value sync.), 75 Pb/Pr : ±0.35V(p-p), 75 Y : 1 V (p-p), Positive (Negative sync provided), 75 Cb/Cr : 0.7V(p-p), 75
Audio
500 mV(rms) (-4dBs), high impedance, RCA pin jack × 2 HDMI 2-row 19pin connector × 1
(Digital-input terminal is not compatible with picture signals of personal computer)
Audio
Digital: HDMI 2-row 19pin connector × 1 Anarog: 500mV(rms) (-4dBs), high impedance, RCA pin jack × 2
R/G/B : 0.7 V (p-p), 75
HD / VD : 1 V (p-p) to 5 V (p-p), high impedance < Available signal >
VGA : 640 pixels × 480 pixels (Horizontal : 31.5 kHz / Vertical : 60 Hz) XGA : 1024 pixels × 768 pixels (Horizontal : 48.4 kHz / Vertical : 60 Hz)
1-2 (No.YA360)
SECTION 1
PRECAUTION
1.1 SAFETY PRECAUTIONS
(1) The design of this product contains special hardware,
many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Service should be performed by qualified personnel only.
(2) Alterations of the design or circuitry of the products should
not be made. Any design alterations or additions will void the manufacturer's warranty and will further relieve the manufacturer of responsibility for personal injury or property damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the parts list of Service manual. Electrical components
having such features are identified by shading on the schematics and by ( ) on the parts list in Service manual. The use of a substitute replacement which does
not have the same safety characteristics as the recommended replacement part shown in the parts list of Service manual may cause shock, fire, or other hazards.
(4) Don't short between the LIVE side ground and
ISOLATED (NEUTRAL) side ground or EARTH side ground when repairing.
Some model's power circuit is partly different in the GND. The difference of the GND is shown by the LIVE : ( ) side GND, the ISOLATED (NEUTRAL) : ( ) side GND and EARTH : ( ) side GND. Don't short between the LIVE side GND and ISOLATED (NEUTRAL) side GND or EARTH side GND and never measure the LIVE side GND and ISOLATED (NEUTRAL) side GND or EARTH side GND at the same time with a measuring apparatus (oscilloscope etc.). If above note will not be kept, a fuse or any parts will be broken.
(5) When service is required, observe the original lead dress.
Extra precaution should be given to assure correct lead dress in the high voltage circuit area. Where a short circuit has occurred, those components that indicate evidence of overheating should be replaced. Always use the manufacturer's replacement components.
(6) Isolation Check (Safety for Electrical Shock Hazard)
After re-assembling the product, always perform an isolation check on the exposed metal parts of the cabinet (antenna terminals, video/audio input and output terminals, Control knobs, metal cabinet, screw heads, earphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.
a) Dielectric Strength Test
The isolation between the AC primary circuit and all metal parts exposed to the user, particularly any exposed metal part having a return path to the chassis should withstand a voltage of 3000V AC (r.m.s.) for a period of one second. (. . . . Withstand a voltage of 1100V AC (r.m.s.) to an appliance rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated 200V or more, for a period of one second.) This method of test requires a test equipment not generally found in the service trade.
b) Leakage Current Check
Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Using a "Leakage Current Tester", measure the leakage current from each exposed metal part of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground (water pipe, etc.). Any leakage current must not exceed 0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.2mA AC (r.m.s.).
Alternate Check Method
Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Use
an AC voltmeter having 1000 per volt or more sensitivity in the following manner. Connect a 1500 10W resistor paralleled by a 0.15µF AC-type capacitor
between an exposed metal part and a known good earth ground (water pipe, etc.). Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Any voltage measured must not exceed 0.75V AC (r.m.s.). This corresponds to
0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.3V AC (r.m.s.). This corresponds to 0.2mA AC (r.m.s.).
AC VOLTMETER (HAVING 1000 /V, OR MORE SENSITIVITY)
0.15 F AC-TYPE
GOOD EARTH GROUND
1500 10W
PLACE THIS PROBE ON EACH EXPOSED ME TAL PAR T
(No.YA360)1-3
1.2 INSTALLATION
1.2.1 HEAT DISSIPATION
If the heat dissipation vent behind this unit is blocked, cooling efficiency may deteriorate and temperature inside the unit will rise. The temperature sensor that protects the unit will be activated when internal temperature exceeds the pre-determined level and power will be turned off automatically.Therefore, please make sure pay attention not to block the heat dissipation vent as well as the ventilation outlet behind the unit and ensure that there is room for ventilation around it.
Ventilation hole
1.2.3 INSTALLATION REQUIREMENTS
To ensure safety in an emergency such as an earthquake, and to prevent accidents, ensure that measures are taken to prevent the TV dropping or falling over. Tie commercially available tough cord(s) to the hooks in the back of the TV, and fix the TV to solid walls or columns.
WALL
HOOK
Ventilation hole
*Diagram differs from actual appearance.
1.2.2 INSTALLATION REQUIREMENTS
Ensure that the minimal distance is maintained, as specified below, between the unit with and the surrounding walls, as well as the floor etc.Install the unit on stable flooring or stands.Take precautionary measures to prevent the unit from tipping in order to protect against accidents and earthquakes.
䎕䎓䎓䏐䏐䎕䎓䎓䏐䏐
150mm150mm
䎘䎓䏐䏐
*Diagram differs from actual appearance.
䎘䎓䏐䏐
HOOK
It fixes in a band.
TV STAND
*Diagram differs from actual appearance.
1.2.4 NOTES ON HANDLING
(1) WHEN TAKING UNIT OUT OF A PACKING CASE
When taking the unit out of a packing case, do not grasp the upper part of the unit. If you take the unit out while grasping the upper part, the LCD PANEL may be damaged because of a pressure. Instead of grasping the upper part, put your hands on the lower backside or sides of the unit.
(2) AS FOR PRESSING OR TOUCHING A SPEAKER
Be careful not to press the opening of the speaker in the lower part of the unit and around them since the decorative sheet on the surface of the openings may be deformed.
1-4 (No.YA360)
1.3 HANDLING LCD PANEL
1.3.1 PRECAUTIONS FOR TRANSPORTATION
When transporting the unit, pressure exerted on the internal LCD panel due to improper handling (such as tossing and dropping) may cause damages even when the unit is carefully packed. To prevent accidents from occurring during transportation, pay careful attention before delivery, such as through explaining the handling instructions to transporters. Ensure that the following requirements are met during transportation, as the LCD panel of this unit is made of glass and therefore fragile:
(1) USE A SPECIAL PACKING CASE FOR THE LCD PANEL
When transporting the LCD panel of the unit, use a special packing case (packing materials). A special packing case is used when a LCD panel is supplied as a service spare part.
(2) ATTACH PROTECTION SHEET TO THE FRONT
Since the front (display part) of the panel is vulnerable, attach the protection sheet to the front of the LCD panel before transportation. Protection sheet is used when a LCD panel is supplied as a service spare part.
(3) AVOID VIBRATIONS AND IMPACTS
The unit may be broken if it is toppled sideways even when properly packed. Continuous vibration may shift the gap of the panel, and the unit may not be able to display images properly. Ensure that the unit is carried by at least 2 persons and pay careful attention not to exert any vibration or impact on it.
(4) DO NOT PLACE EQUIPMENT HORIZONTALLY
Ensure that it is placed upright and not horizontally during transportation and storage as the LCD panel is very vulnerable to lateral impacts and may break. During transportation, ensure that the unit is loaded along the traveling direction of the vehicle, and avoid stacking them on one another. For storage, ensure that they are stacked in 2 layers or less even when placed upright.
1.3.2 OPTICAL FILTER (ON THE FRONT OF THE LCD PANEL)
(1) Avoid placing the unit under direct sunlight over a
prolonged period of time. This may cause the optical filter to deteriorate in quality and COLOUR.
(2) Clean the filter surface by wiping it softly and lightly with a
soft and lightly fuzz cloth (such as outing flannel).
(3) Do not use solvents such as benzene or thinner to wipe the
filter surface. This may cause the filter to deteriorate in quality or the coating on the surface to come off. When cleaning the filter, usually use the neutral detergent diluted with water. When cleaning the dirty filter, use water-diluted ethanol.
(4) Since the filter surface is fragile, do not scratch or hit it with
hard materials. Be careful enough not to touch the front surface, especially when taking the unit out of the packing case or during transportation.
1.3.3 PRECAUTIONS FOR REPLACEMENT OF EXTERIOR PARTS
Take note of the following when replacing exterior parts (REAR COVER, FRONT PANEL, etc.):
(1) Do not exert pressure on the front of the LCD panel (filter
surface). It may cause irregular COLOUR.
(2) Pay careful attention not to scratch or stain the front of the
LCD panel (filter surface) with hands.
(3) When replacing exterior parts, the front (LCD panel) should
be placed facing downward. Place a mat, etc. underneath to avoid causing scratches to the front (filter surface).
(No.YA360)1-5
2.1 SYSTEM SETTEING
LOB OK FAN OK SYNC M:OK S:OK HD:NG TIM OK MSM OK DIGI 0000 MEM OK AVSW OK YC OK AIO OK TUN OK GCR NG 1 IP OK RGB OK 8 DVI OK HDMI OK
SERVICE MENU
1.ADJUST
2.SELF_CHECK
3.I2C STOP
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
Be sure to carry out the following operation at the end of the procedure.
(1) Press the [INFORMATION] key and [MUTING] key
simultaneously, then enter the SERVICE MODE.
(2) When the Main Menu is displayed, press [2] key to enter
the self check mode.
(3) Turn off the power by pressing the [POWER] key on the
remote control unit.
2.2 FEATURES
D.I.S.T. (Digital Image Scaling Technology)
This system uses line interpolation to double the number of scanning lines and achieve high resolution, flicker-free picture.
COLOUR MANAGEMENT
This function ensures dull colours are compensated to produce natural hues.
PICTURE MANAGEMENT
This function makes it easier to see the dark areas when a picture has many dark areas, and makes it easier to see the bright areas when a picture has many bright areas.
ZOOM
This function can change the screen size according to the picture aspect ratio.
MAIN MENU SCREEN
SERVICE MENU
1.ADJUST
2.SELF_CHECK
3.I2C STOP
SELF CHECK MODE SCREEN
LOB OK FAN OK SYNC M:OK S:OK HD:NG TIM OK MSM OK DIGI 0000 MEM OK AVSW OK YC OK AIO OK TUN OK GCR NG 1 IP OK RGB OK 8 DVI OK HDMI OK
DIGITAL VNR
This function cuts down the amount of noise in the original picture.
SUPER DIGIPURE
This function uses the latest in digital technology to give you a natural-looking picture.
MOVIE THEATRE
This function displays a cinema film picture more smoothly and naturally on the screen.
3D CINEMA SOUND
You can enjoy sounds with a widerambience.
2.3 MAIN DIFFERENCE LIST
Item LT-37M60BU LT-37M60BU/P LT-37M60ZU LT-37M60ZU/P
CABINET COLOUR SILVER / BLACK BLACK STAND COLOUR SILVER / BLACK BLACK
DIGITAL SIGNAL PWB SFL0D234A-U2
LCA10557-67A
(SFL-0D234A)
SFL0D234A-U2
LCA10557-67A
(SFL-0D234A)
1-6 (No.YA360)
2.4 HOW TO IDENTIFY MODELS
LT-37M60BU and LT-37M60ZU: "AE" is added to the serial No. after at the Rating label. LT-37M60BU/P and LT-37M60ZU/P: "PE" is added to the serial No. after at the Rating label.
MODEL No.
LT-37M60BU
LT-37M60ZU
AE
SERIAL NO.
PE
Indicated
2.5 21-PIN EURO CONNECTOR (SCART) : EXT-1 / EXT-2
Pin No. Signal designation Matching value EXT-1 EXT-2
1 AUDIO R output 500mV(rms) (Nominal), Low impedance Used (TV OUT) Used (LINE OUT)
2 AUDIO R input 500mV(rms) (Nominal), High impedance Used (R1) Used (R2)
3 AUDIO L output 500mV(rms) (Nominal), Low impedance Used (TV OUT) Used (LINE OUT)
4 AUDIO GND Used Used
5 GND (B) Used Used
6 AUDIO L input 500mV(rms) (Nominal), High impedance Used (L1) Used (L2)
7 B input 700mV
8 FUNCTION SW
(SLOW SW)
Low : 0V-3V High : 8V-12V, High impedance
, 75 Used Used
(B-W)
Used Used
9 GND (G) Used Used
10 SCL / T-V LINK Not used Used (SCL2 / TV-LINK)
11 G input 700mV
, 75 Used Used
(B-W)
12 SDA Not used Used (SDA2)
13 GND (R) Used Used
14 GND (YS) Used Not used
15 R / C input R : 700mV
C : 300mV
(B-W) (P-P)
, 75
, 75
Used (R) Used (C2/R)
16 Ys input (FAST SW) Low : 0V-0.4V, High : 1V-3V, 75 Used Used
17 GND (VIDEO output) Used Used
18 GND (VIDEO input) Used Used
19 VIDEO output 1V
20 VIDEO / Y input 1V
(Negative sync), 75 Used (TV OUT) Used (LINE OUT)
(P-P)
(Negative sync), 75 Used Used
(P-P)
21 COMMON GND Used Used
(P-P= Peak to Peak, B-W= Blanking to white peak)
[Pin assignment]
20 18 16 14 12 10 8 6 4 2
21 19 17 15 13 11 9 7 5 3 1
(No.YA360)1-7
2.6 TECHNICAL INFORMATION
2.6.1 LCD PANEL
This unit uses the flat type panel LCD (Liquid Crystal Display) panel that occupies as little space as possible, instead of the conventional CRT (Cathode Ray Tube), as a display unit. Since the unit has the two polarizing filter that are at right angles to each other, the unit adopts "normally black" mode, where light does not pass through the polarizing filter and the screen is black when no voltage is applied to the liquid crystals.
2.6.1.1 SPECIFICATIONS
The following table shows the specifications of this unit.
Item Specifications
Maximum dimensions ( W × H × D ) 877.0 mm × 514.6 mm × 56.0 mm
Weight 8.5 kg
Effective screen size Diagonal: 940 mm (H: 819.6 mm × V: 460.8 mm)
Aspect ratio 16 : 9
Drive device / system a-Si-TFT active matrix system
Resolution Horizontally 1366 × Vertically 768 × RGB < W-XGA > 3147264 dots in total
Pixel pitch (pixel size) Horizontally: 0.6 mm Vertically: 0.6 mm
Displayed colour 16777216 colours 256 colours for R G and B
Brightness 500cd/m2
Contrast ratio 1050 : 1
Response time less than 12ms
View angle Horizontally: 176° Vertically: 176°
Surface polarizer Anti-Glare type Low reflective coat
Colour filter Vertical stripe
Backlight Direct-type Cold cathode fluorescent lamp × 18
Power supply voltage in LCD 5 V
Power supply voltage in inverter 24 V
Panel interface system LVDS (Low Voltage Differential Signaling)
2.6.1.2 PIXEL FAULT
There are three pixel faults - bright fault , dark fault and flicker fault - that are respectively defined as follows.
BRIGHT FAULT
In this pixel fault, a cell that should not light originally is lighting on and off. For checking this pixel fault, input ALL BLACK SCREEN and find out the cell that is lighting on and off.
DARK FAULT
In this pixel fault, a cell that should light originally is not lighting or lighting with the brightness twice as brighter as originally lighting. For checking this pixel fault, input 100% of each R/G/B colour and find out the cell that is not lighting.
FLICKER FAULT
In the pixel fault, a cell that should light originally or not light originally is flashing on and off. For checking this pixel fault, input ALL BLACK SCREEN signal or 100% of each RGB colour and find out the cell that is flashing on and off.
1-8 (No.YA360)
2.6.2 MAIN CPU PIN FUNCTION [IC7501 : DIGITAL SIGNAL PWB]
Pin Pin name I/O Function Pin Pin name I/O Function
1 TCK I Test purpose 65 D2 I/O Program ROM data for main CPU 2 TMS I Test purpose 66 D12 I/O Program ROM data for main CPU 3 TDI I Test purpose 67 D10 I/O Program ROM data for main CPU 4 TDO O Test purpose 68 VSS33 - GND 5 P2.8 O Not used 69 VDD33 I 3.3V 6 P2.9 O Blue for OSD 70 D4 I/O Program ROM data for main CPU 7 P2.10 O Blue for OSD 71 D3 I/O Program ROM data for main CPU 8 P2.11 O Blue for OSD 72 D11 I/O Program ROM data for main CPU
9 P2.12 O Blue for OSD 73 RSTIN I Reset 10 P2.13 O Blue for OSD 74 POWER O Sleep state release for chassis CPU [Relese : L] 11 P2.14 I Not used 75 P3.1 O Not used 12 P2.15 O Request for chassis CPU communication 76 REMOCON I Remote control 13 VSS33 - GND 77 P3.3 I Clock for OSD 14 VDD33 I 3.3V 78 P3.4 O Red for OSD 15 P4.5 O Not used 79 P3.5 O Red for OSD 16 A20 O Program ROM address for main CPU 80 P3.6 O Red for OSD 17 A19 O Program ROM address for main CPU 81 P3.7 O Red for OSD 18 A18 O Program ROM address for main CPU 82 MTST O Data transmission for chassis CPU communication 19 A17 O Program ROM address for main CPU 83 MTSR I Data receive for chassis CPU communication 20 VSS25 - GND 84 VSS33 - GND 21 VDD25 I 2.5V 85 VDD33 I 3.3V 22 A16 O Program ROM address for main CPU 86 VSS25 - GND 23 A8 O Program ROM address for main CPU 87 VDD25 I 2.5V 24 A7 O Program ROM address for main CPU 88 TXD0 O Communication for adjustment 25 A9 O Program ROM address for main CPU 89 RXD0 O Communication for adjustment 26 A6 O Program ROM address for main CPU 90 P3.12 O Red for OSD 27 A5 O Program ROM address for main CPU 91 CLK O Clock for chassis CPU communication 28 A10 O Program ROM address for main CPU 92 P3.15 O Green for OSD 29 A11 O Program ROM address for main CPU 93 P5.14 O Green for OSD 30 A12 O Program ROM address for main CPU 94 P5.15 O Green for OSD 31 VSS33 - GND 95 TRIG_IN O Green for OSD 32 VDD33 I 3.3V 96 TRIG_OUT O Green for OSD 33 A4 O Program ROM address for main CPU 97 P6.2 O Green for OSD 34 A3 O Program ROM address for main CPU 98 P6.3 O I 35 A2 O Program ROM address for main CPU 99 P6.4 I/O I 36 A1 O Program ROM address for main CPU 100 P6.5 O Teletext signal select [Analog RGB : H / Digital RGB : L] 37 A0 O Program ROM address for main CPU 101 IRQ O Not used 38 A13 O Program ROM address for main CPU 102 VSYNC I Vertical sync 39 ARAS/A14 O Program ROM address for main CPU 103 HSYNC I Horizontal sync 40 CAS/A15 O Program ROM address for main CPU 104 41 VSS33 - GND 105 BLANK O Ys for OSD / Teletext 42 VDD33 I 3.3V 106 VDD33 I 3.3V 43 MEMCLK O Clock for memory 107 VSS33 - GND 44 CSSDRAM O Chip select for memory 108 XTAL1 I 6MHz for system clock 45 CLKEN O Clock enable for memory 109 XTAL2 O 6MHz for system clock 46 CSROM O Chip select for memory 110 VSSA - GND 47 RD O Read for memory 111 VDDA I 2.5V 48 UDQM O Control buffer of memory 112 R O R for OSD / Teletext 49 LDQM O Control buffer of memory 113 G O G for OSD / Teletext 50 WR O Write for memory 114 B O B for OSD / Teletext 51 D15 I/O Program ROM data for main CPU 115 VSSA - GND 52 VSS33 - GND 116 VDDA I 2.5V 53 VDD33 I 3.3V 117 CVBS2 I Video for Teletext 54 D7 I/O Program ROM data for main CPU 118 VSSA - GND 55 D0 I/O Program ROM data for main CPU 119 VDDA I 2.5V 56 D14 I/O Program ROM data for main CPU 120 CVBS1B I Video for Teletext 57 D8 I/O Program ROM data for main CPU 121 CVBS1A I Video for Teletext 58 D6 I/O Program ROM data for main CPU 122 VSSA - GND 59 D1 I/O Program ROM data for main CPU 123 VDDA I 2.5V 60 VSS33 - GND 124 KEY1 I Key scan data 1 [ON : H] 61 VDD33 I 3.3V 125 KEY2 I Key scan data 2 [ON : H] 62 D13 I/O Program ROM data for main CPU 126 MECA_SW I Main power ON / OFF control [ON : L] 63 D9 I/O Program ROM data for main CPU 127 P5.3 I Not used 64 D5 I/O Program ROM data for main CPU 128 TMODE I Test purpose
COR/RSTOUT
2
C bus clock (for main memory)
2
C bus Data (for main memory)
O Not used
(No.YA360)1-9
2.6.3 SUB (CHASSIS) CPU PIN FUNCTION [IC7001 : DIGITAL SIGNAL PWB]
Pin Pin name I/O Function Pin Pin name I/O Function
1 LB_PRO O Not used 51 BS_TXD O Not used : 2 P_MU O Picture muting [Muting = H] 52 BS_RXD I Not used : Data receive for digital tuner communication 3 JP_CSB O Not used (NC) 53 NC O Not used (NC) 4 A_MU O Audio muting [Muting = H] 54 VREF+ I 3.3V power supply 5 M_MU O Audio muting (for AUDIO OUT) [Muting = H] 55 PDP_TX O 6 PC_SEL O RGB(PC) INPUT select 56 PDP_RX I Data receive for SUB (DRIVE) CPU communication 7 ON_TIMER O POWER INDICATOR (LED) brightness [LOW = L] 57 SDA0 I/O Data for Inter IC (serial) bus : EEP-ROM (IC7002) 8 ILA0 O LCD back light lighting 58 SCL0 O Clock for Inter IC (serial) bus : EEP-ROM (IC7002)
9 ILA1 O LCD panel overshoot refresh timing 59 SDA_DVI I/O 10 ILA2 O Not used 60 SCL_DVI O 11 POW_LED O POWER LED lighting [ON = H] 61 AVSS - GND 12 WORD O Not used 62 DIGII_PHOT I Photo sensor for DIGITAL-IN illegal copy protection 13 MI_CK I Clock for main CPU communication 63 AGC I Not used 14 MI_TX I Data receive for main CPU communication 64 EXT_YS1 I Not used 15 MI_RX O Data transmission for MAIN CPU communication 65 EXT_YS2 I Not used 16 MI_REQ O 17 VDD I 3.3V power supply 67 DIGI_PRO O Not used : For DIGITAL-IN (HDMI) 18 FOSC O Not used (NC) 68 GCR_RST O Not used (NC) 19 VSS - GND 69 GR_ON O Not used (NC) 20 X1 I Not used : Low speed oscillatior 70 SYNC_SEL O Not used : Sync select for digital tuner 21 X0 O Not used : Low speed oscillatior 71 NC O Not used (NC) 22 VDD I 3.3V power supply 72 NC O Not used (NC) 23 OSC1 I System clock osillation (crystal) : 16MHz 73 SBD5 I/O 24 OSC0 O System clock osillation (crystal) : 16MHz 74 SBT5 I 25 MODE I Single chip mode 75 NMI I 3.3V power supply 26 BS1.5CTL O Not used : Digital tuner power / reset control 76 COMP I Not used : AV COMPULINK lll control 27 A92RES O 28 BS_RST O Not used : Reset for Digital tuner power / reset control 78 VSYNC I V. sync pulse 29 LIP_RST O Not used : Reset for Sound delay (Lip sync) 79 WAKE I Reset for sub(chassis) CPU 30 SOFT_OFF O Not used 80 31 VMUTE I Picture muting request from digital tuner 81 NC O Not used (NC) 32 VOUTENB O Not used : Video cutoff for digital tuner 82 RST I Reset for MAIN CPU [Reset = L] 33 MDR_CON I Not used: System cable connection monitor for PDP 83 VDD I 3.3V power supply 34 AVDD I 3.3V power supply 84 SCL3A O Clock for Inter IC (serial) bus control 35 BS_POW O Not used : Digital tuner power control 85 SDA3A I/O Data for Inter IC (serial) bus control
DsyncSW2
36 37 LB_POW O Power control for low bias line 87 SDA3B I/O Data for Inter IC (serial) bus control 38 NC O Not used (NC) 88 39 HOTPLUG I 40 MECA_SW I Mechanical monitor for POWER switch [Push = L] 90 DIGI_INT I Reset for HDMI process [Reset = L ] 41 MAIN_POW O Main power control [ON = L] 91 DVI_RST O Not used : Reset for DVI format conversion 42 MSP_RST O AUDIO OUT output mode select [VARIABLE = L] 92 VSS - GND 43 VREF- I Not used 93 SCL5055 O 44 AFT2 I Not used : AFT voltage for sub tuner 94 45 AFT1 I AFT voltage for VHF/UHF tuner 95 SDA5055 I/O Data for Inter IC (serial) bus : JCC5055 (DIST process) 46 KEY2 I Key scan data for front switch (MENU/CH+/CH-) 96 47 KEY1 I Key scan data for front switch (VOL+/VOL-) 97 NC O Not used (NC) 48 NC O Not used (NC) 98 15K/OTH O Main video select [Fixed = H] 49 NC O Not used (NC) 99 DsyncSW1 O Sync select for DIGITAL-IN [Cotrolled with 36-pin] 50 AC_IN I Not used : AC 50/60Hz detect 100 57 BUSY I Busy monitor for IC4001 (New DIST process)
Data request for main CPU communication [Request = L]
Reset for IC1001(3D YC SEP / COLOUR DEMODULAT) [Reset = H]
O Sync select for DIGITAL-IN [Cotrolled with 99-pin] 86 SCL3B O Clock for Inter IC (serial) bus control
Not used : Video communiation monitor for receiver unit (PDP)
66 VDD I 3.3V power supply
77 REMO I Remote control
POWERGOOD
DIGI_SYNCSEL
89 DIGI_LRSW O Not used : For DIGITAL-IN (HDMI)
VFORMATSEL
OSD_MODE_SEL
Data transmission for SUB (DRIVE) CPU communication
Not used : Data for Inter IC (serial) bus for panel communication Not used : Clock for Inter IC (serial) bus for panel communication
Not used : Data for writing on board (connect CN01P : for Frash ROM type) Not used : Clock for writing on board (connect CN01P : for Frash ROM type)
I Power error detection [NG = H]
O Not used
Clock for Inter IC (serial) bus : JCC5055 (DIST process)
O Not used : Digital tuner clock control
O Not used : OSD mode select
Data transmission for digital tuner communicati on
1-10 (No.YA360)
SECTION 3
DISASSEMBLY
3.1 DISASSEMBLY PROCEDURE
CAUTION AT DISASSEMBLY:
Be sure to perform the SYSTEM SETTEING, at the end of the procedure.
• Make sure that the power cord is disconnected from the outlet.
• Pay special attention not to break or damage the parts.
• When removing each board, remove the connectors as required. Taking notes of the connecting points (connector numbers) makes service procedure manageable.
• Make sure that there is no bent or stain on the connectors before inserting, and firmly insert the connectors.
3.1.1 REMOVING THE STAND (Fig.1)
(1) Remove the 2 screw [A], then remove the STAND
COVER.
(2) Remove the 4 screws [B], then remove the STAND.
3.1.2 REMOVING THE REAR COVER (Fig.1)
• Remove the STAND. (1) Remove the JACK COVER (L/R). (2) Remove the 10 screws [C], the 3 screws [D], and the 2
screws [E].
(3) Remove the REAR COVER.
3.1.3 REMOVING THE REGULATOR PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER. (1) Remove the 4 screws [F], then remove the FAN
BRACKET.
(2) Remove the 1 screw [G], then remove the POWER CORD
HOLDER. (3) Remove the POWER CORD from the POWER PWB. (4) Remove the REGULATOR PWB.
3.1.4 REMOVING THE POWER PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the FAN BRACKET. (1) Remove the 4 screw [H], then remove the POWER PWB.
3.1.5 REMOVING THE PANEL I/F PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the FAN BRACKET. (1) Remove the 4 screws [J], then remove the PANEL I/F
PWB.
3.1.6 REMOVING THE ANALOG SYGNAL PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the FAN BRACKET. (1) Remove the 3 screws [K], then remove the TERMINAL
BASE.
(2) Remove the 4 screws [L], then remove the PANEL I/F
PWB BRACKET.
(3) Remove the 3 screws [M] and 2screw [N], then remove the
ANALOG SIGNAL PWB.
3.1.7 REMOVING THE FRONT CONTROL PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER. (1) Remove the 3 screws [P], then remove the CONTROL
ASSY with the FRONT CONTROL PWB.
(2) Remove the FRONT CONTROL PWB.
3.1.8 REMOVING THE RECEIVER PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER. (1) Remove the 3 screws [Q] and the 1 screw [R], then remove
the TUNER BASE.
(2) Remove the 4 screws [S], then remove the RECEIVER PWB.
3.1.9 REMOVING THE CONNECTOR PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the TOP SHIELD CASE. (1) Remove the 4 screws [T], then remove the RECEIVER
PWB BRACKET.
(2) Remove the 1 screw [U], then remove the CONNECTOR PWB.
3.1.10 REMOVING THE DIGITAL SIGNAL PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the TUNER BASE. (1) Remove the 7 screws [V] and the 3 screws [W], then
remove the SHIELD COVER.
(2) Remove the 5 screws [X], then remove the DIGITAL
BRACKET.
(3) Remove the DIGITAL SIGNALPWB.
CAUTION :
Make sure to perform the "SYSTEM SETTEING" according to before page, when DIGITAL SIGNAL PWB is replaced.
(No.YA360)1-11
JACK COVER
JACK COVER
A
STAND COVER
E
C
H
PANEL I/F PWB
REGULATOR PWB
G
J
D
POWER PWB
POWER CORD HOLDER
REAR COVER
POWER CORD
S
RECEIVER PWB
BRACKET
RECEIVER PWB
U
F
FAN BRACKET
T
B
SHIELD COVER
F
X
TUNER BASE
W
V
TOP SHIELD CASE
STAND
R
SIDE SHIELD CASE
Q
ANALOG SIGNAL PWB
TERMINAL BASE
K
P
CONTROL ASSY
1-12 (No.YA360)
L
FRONT CONTROL PWB
P
PANEL I/F PWB
N
BRACKET
M
CONNECTOR PWB
DIGITAL SIGNAL PWB
Fig.1
3.1.11 REMOVING THE SPEAKER (Fig.2)
• Remove the STAND.
• Remove the REAR COVER. (1) Remove the 6 screws [A], then remove the SPEAKER (L /R).
NOTE:
• Since the speaker is attached in a certain direction, attach
the speaker in the same correct direction as it has been attached.
• When the speaker is decomposed, the performance cannot
be kept.
3.1.12 REMOVING THE FRONT LED PWB (Fig.2)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the FAN BRACKET. (1) Remove the 2 screws [B], then remove the FRONT LED
PWB.
3.1.13 REMOVING THE LED LENS (Fig.2)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the FAN BRACKET.
• Remove the FRONT LED PWB. (1) Remove the 2 screws [C], then remove the LED LENS.
3.1.14 REMOVING THE CARD PWB (Fig.2)
• Remove the STAND.
• Remove the REAR COVER. (1) Remove the CARD SHIELD. (2) Remove the 4 screws [D], then remove the CARD PWB.
3.1.15 REMOVING THE LCD PANEL UNIT (Fig.2)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the FAN BRACKET. (1) Remove the 2 screws [E], then remove the CARD BASE. (2) Remove the 2 screws [F], then remove the CARD PWB
BRACKET. (3) Remove the 2 screws [G], then remove the MAIN BASE. (4) Remove the 3 screws [H], the 2 screws [J] and the 1 screw
[K], then remove the TOP FRAME. (5) Remove the 2 screws [L] and the 2 screws [M], then
remove the BOTTOM FRAME. (6) Remove the LCD PANEL UNIT from the FRONT PANEL.
NOTE:
• Pay special attention not to break or damage on the FRONT
PANEL.
• The LCD PANEL UNIT is fixed to the FRONT PAMEL (at the
back side)by using double-side adhesive tapes. To remove the LCD PANEL UNIT, remove the adhesive tape on the FRONT PANEL slowly.
(No.YA360)1-13
CARD SHIELD
E
G
TOP FRAME
D
CARD PWB
MAIN BASE
CARD BASE
F
H
J
K
L
M
CARD PWB BRACKET
BOTTOM FRAME
SPEAKER
A
A
SPEAKER
B
FRONT LED PWB
C
LED LENS
FRONT PANEL
FRONT
1-14 (No.YA360)
Fig.2
3.2 MEMORY IC REPLACEMENT
S001 PREPARE 0 PAL50 FULL STD H
SERVICE MENU
1.ADJUST
2.SELF_CHECK
3.I2C STOP
• This model uses the memory IC.
• This memory IC stores data for proper operation of the video and drive circuits.
• When replacing, be sure to use an IC containing this (initial value) data.
3.2.1 MEMORY IC REPLACEMENT PROCEDURE
1. Power off
Switch off the power and disconnect the power plug from the AC outlet.
2. Replace the memory IC
Be sure to use the memory IC written with the initial setting values.
3. Power on
Connect the power plug to the AC outlet and switch on the power.
4. Receiving channel setting
Refer to the OPERATING INSTRUCTIONS and set the receive channels (Channels Preset) as described.
5. User setting
Check the user setting items according to the given in page later. Where these do not agree, refer to the OPERATING INSTRUCTIONS and set the items as described.
6. SERVICE MODE setting
Verify what to set in the SERVICE MODE, and set whatever is necessary (Fig.1). Refer to the SERVICE ADJUSTMENT for setting.
3.2.2 SERVICE MODE SETTING
SERVICE MODE SCREEN
MAIN MENU SCREEN
SETTING ITEM
Setting items Settings Item No.
Video system setting Adjust S001 - S039
SERVICE MENU
1.ADJUST
2.SELF_CHECK
3.I2C STOP
Audio system setting Fixed T001 - T010
Panel control system setting Fixed P001 - P010
Drive system setting Fixed D001 - D187
Main CPU system setting Fixed Z001 - Z010
ADJUSTMENT MODE SCREEN
S001 PREPARE 0 PAL50 FULL STD H
Fig.1
(No.YA360)1-15
3.2.3 SETTINGS OF FACTORY SHIPMENT
3.2.3.1 BUTTON OPERATION 3.2.3.2 REMOTE CONTROL DIRECT OPERATION
Setting item Setting position
POWER Off
CHANNEL PR1
VOLUME 10
TV/AV TV
3.2.3.3 REMOTE CONTROL MENU OPERATION
(1) PICTURE
Setting item Setting position
PICTURE MODE BRIGHT
COLOUR TEMP. COOL
FEATURES
DIGITAL VNR AUTO (LOW)
Super DigiPure AUTO
MOVIE THEATRE AUTO
COLOUR MANAGEMENT ON
PICTURE MANAGEMENT ON
COLOUR SYSTEM TV Depends on PR/CH
EXT AUTO
4:3 AUTO ASPECT PANORAMIC
(2) SOUND
Setting item Setting position
STEREO / I•II Stereo sound
BASS Centre
TREBLE Centre
BALANCE Centre
3D SOUND OFF
A.H.B. ON
BBE ON
CHANNEL PR1
VOLUME 10
ZOOM PANORAMIC
3D SOUND OFF
(4) FEATURES
SLEEP TIMER OFF
CHILD LOCK ID NO.0000, All CH off
APPEARANCE TYPE D
BLUE BACK ON
FAVOURITE SETTING Reset
ILLUMINATION BRIGHT
(5) SET UP
AUTO PROGRAM TV channel automatically set
EDIT/MANUAL PRESET CH only
LANGUAGE ENGLISH
DECODER (EXT-2) OFF
COMPONENT AUTO SELECT ON
HDMI SETTING AUTO
EXT SETTING
S-IN BLANK
ID BLANK
DUBBING EXT-1 EXT-2
Setting item Setting position
Setting item Setting position
Setting item Setting position
1-16 (No.YA360)
3.3 REPLACEMENT OF CHIP COMPONENT
3.3.1 CAUTIONS
(1) Avoid heating for more than 3 seconds. (2) Do not rub the electrodes and the resist parts of the pattern. (3) When removing a chip part, melt the solder adequately. (4) Do not reuse a chip part after removing it.
3.3.2 SOLDERING IRON
(1) Use a high insulation soldering iron with a thin pointed end of it. (2) A 30w soldering iron is recommended for easily removing parts.
3.3.3 REPLACEMENT STEPS
1. How to remove Chip parts
2. How to install Chip parts
[Resistors, capacitors, etc.]
(1) As shown in the figure, push the part with tweezers and
alternately melt the solder at each end.
(2) Shift with the tweezers and remove the chip part.
[Transistors, diodes, variable resistors, etc.]
(1) Apply extra solder to each lead.
SOLDER
SOLDER
[Resistors, capacitors, etc.]
(1) Apply solder to the pattern as indicated in the figure.
(2) Grasp the chip part with tweezers and place it on the
solder. Then heat and melt the solder at both ends of the
chip part.
[Transistors, diodes, variable resistors, etc.]
(1) Apply solder to the pattern as indicated in the figure. (2) Grasp the chip part with tweezers and place it on the
solder. (3) First solder lead A as indicated in the figure.
(2) As shown in the figure, push the part with tweezers and
alternately melt the solder at each lead. Shift and remove the chip part.
NOTE :
After removing the part, remove remaining solder from the pattern.
A
B
C
(4) Then solder leads B and C.
A
B
C
(No.YA360)1-17
SECTION 4
SERVICE MENU
1.ADJUST
2.SELF_CHK
3.I2C STOP
S001 PREPARE 0 PAL50 FULL STD H
ADJUSTMENT
4.1 ADJUSTMENT PREPARATION
(1) There are 2 ways of adjusting this TV : One is with the
REMOTE CONTROL UNIT and the other is the conventional method using adjustment parts and components.
(2) The adjustment using the REMOTE CONTROL UNIT is
made on the basis of the initial setting values. The setting values which adjust the screen to the optimum condition can be different from the initial setting values.
(3) Make sure that connection is correctly made AC to AC
power source.
(4) Turn on the power of the TV and measuring instruments for
warming up for at least 30 minutes before starting adjustments.
(5) If the receive or input signal is not specified, use the most
appropriate signal for adjustment.
(6) Never touch the parts (such as variable resistors,
transformers and condensers) not shown in the adjustment items of this service adjustment.
4.2 PRESET SETTING BEFORE ADJUSTMENTS
Unless otherwise specified in the adjustment items, preset the following functions with the REMOTE CONTROL UNIT.
Setting item Settings position
PICTURE MODE STANDARD
PICTURE adjustments Centre
COLOUR TEMP. NORMAL
DIGITAL VNR AUTO (LOW)
Super DigiPure AUTO
MOVIE THEATRE AUTO
COLOUR MANAGEMENT ON
PICTURE MANAGEMENT ON
SOUND adjustments Centre
BBE OFF
3D SOUND OFF
A.H.B OFF
ZOOM FULL
4.3 MEASURING INSTRUMENT AND FIXTURES
• Oscilloscope
• Signal generator (Pattern generator) [PAL / 625i / 625p / 1125i(50Hz)]
• Remote control unit
4.4 ADJUSTMENT ITEMS
VIDEO CIRCUIT
• 625i A-D OFFSET adjustment
• 1125i(50Hz) BRIGHTNESS adjustment
• 1125i(50Hz) A-D OFFSET adjustment
• SUB SCREEN A-D OFFSET adjustment
• WHITE BALANCE (HIGH LIGHT) adjustment
4.5 BASIC OPERATION OF SERVICE MODE
4.5.1 HOW TO ENTER THE SERVICE MODE
(1) Press [INFORMATION] key and [MUTING] key on the
remote control unit simultaneously to enter the SERVICE MODE SCREEN.
(2) In the SERVICE MENU, press the [1] key to display
ADJUSTMENT MODE SCREEN.
NOTE:
• Before entering the SERVICE MODE, confirm that the setting of VCR/TV/DVD switch is at the "TV" side. If the switches have not been properly set, you cannot enter the SERVICE MODE.
• When a number key other than the [1] key is pressed in the SERVICE MODE SCREEN, the other relevant screen may be displayed. This is not used in the adjustment procedure. Press the [MENU] key to return to the SERVICE MODE SCREEN.
SERVICE MODE SCREEN
SERVICE MENU
1.ADJUST
2.SELF_CHK
3.I2C STOP
ADJUSTMENT MODE SCREEN
S001 PREPARE 0 PAL50 FULL STD H
1-18 (No.YA360)
4.5.2 HOW TO EXIT THE SERVICE MODE Press the [MENU] key to exit the Service mode.
4.5.3 DESCRIPTION OF STATUS DISPLAY
S001 PREPARE 0 PAL50 FULL STD H
SETTING VALUE (DATA)SETTINGITEM No. SETTING ITEM
S001 PREPARE 0 PAL50 FULL STD H
SIGNAL SYSTEM
ZOOM MODE
PICTURE MODE
COLOUR TEMP.
(1) SIGNAL SYSTEM
The signal displayed on the screen is displayed.
PAL50 : PAL50Hz (Composite / S-video) PAL60 : PAL60Hz (Composite / S-video) SECAM : SECAM NTSC3 : NTSC3.58 NTSC4 : NTSC4.43 525I : 525i (Component) 525P : 525p 625I : 625i (Component) 625P : 625p 1125I5 : 1125i 50Hz 1125I6 : 1125i 60Hz RGB5 : RGB 525i RGB6 : RGB 625i PCVGA : PC (VGA) PCXGA : PC (XGA) H525I : HDMI 525i H525P : HDMI 525p H625I : HDMI 625i H625P : HDMI 625p H750P : HDMI 750p H125I5 : HDMI 1125i 50Hz H125I6 : HDMI 1125i 60Hz
(2) ZOOM MODE
State of the SCREEN SIZE or MULTI PICTURE is displayed.
SINGLE SCREEN
FULL : FULL PANO : PANORAMIC 1609 : 16:9 ZOOM 1609S : 16:9 ZOOM SUBTITLE 1409 : 14:9 ZOOM REGU : REGULAR
MULTI SCREEN
M2 : 2-pictures multi M12 : 12-pictures multi
(3) PICTURE MODE
STD : STANDARD BRI : BRIGHT SOFT : SOFT
(4) COLOUR TEMP.
H : COOL M : NORMAL L: WARM
(5) SETTING ITEM NAME
Setting item name are displayed. The setting item numbers to be displayed are listed below.
Item No. Setting item
S001 to S039 Video system setting
T001 to T010 Audio system setting
P001 to P010 Panel control system setting
D001 to D187 Drive system setting
Z001 to Z010 Main CPU system setting
(6) SETTING ITEM NO.
Setting item numbers are displayed. For the setting item names to be displayed, refer to "INITIAL SETTING VALUES IN THE SERVICE MODE".
(7) SETTING VALUE (DATA)
The SETTING VALUE is displayed.
4.5.4 CHANGE AND MEMORY OF SETTING VALUE
SELECTION OF SETTING ITEM
[FUNCTION /] key.
For scrolling up / down the setting items.
S001... T001... P001... D001... Z001...
CHANGE OF SETTING VALUE (DATA)
[FUNCTION /] key.
For scrolling up / down the setting values.
MEMORY OF SETTING VALUE (DATA)
Changed setting value is memorized by pressing [MUTING] key.
4.5.5 SERVICE MODE SELECT KEY LOCATION
MUTING
NUMBER
VCR/TV/DVD switch
INFORMATION
ZOOM (Red)
3D SOUND (Green)
MENU
FUNCTION /
FUNCTION /
(No.YA360)1-19
4.6 INITIAL SETTING VALUES IN THE SERVICE MODE
• Perform fine-tuning based on the "initial values" using the remote control when in the Service mode.
• The "initial values" serve only as an indication rough standard and therefore the values with which optimal display can be achieved may be different from the default values. But, don't change the values that are not written in "ADJUSTMENT PROCEDURE". They are fixed values.
4.6.1 VIDEO SYSTEM SETTING 4.6.2 AUDIO SYSTEM SETTING (*Fixed values)
Item No. Item name Variable range Setting value
S001 PREPARE 0 - 31 0
S002 NTSC BL 0 - 15 0
S003 NTSC CNT 0 - 255 53
S004 NT CR OF 0 - 15 6
S005 NT CB OF 0 - 15 6
S006 525i BL 0 - 15 0
S007 525i CNT 0 - 255 53
S008 5i CB OF 0 - 15 0
S009 5i CR OF 0 - 15 0
S010 5i CR GN 0 - 15 6
S011 5i CB GN 0 - 15 6
S012 HD BL 0 - 63 62
S013 HD CB OF 0 - 63 59
S014 HD CR OF 0 - 63 57
S015 RT CONT 0 - 15 8
S016 RT CB OF 0 - 15 6
S017 RT CR OF 0 - 15 6
S018 RT CL GA 0 - 15 1
S019 PC CL MB 0 - 7 0
S020 PC CL LB 0 - 31 0
S021 PC CL MR 0 - 71 0
S022 PC CL LR 0 - 31 0
S023 (Not display) 0 - 255 0
S024 (Not display) 0 - 255 0
S025 (Not display) 0 - 255 0
S026 (Not display) 0 - 255 0
S027 (Not display) 0 - 255 0
S028 (Not display) 0 - 255 0
S029 (Not display) 0 - 255 0
S030 R DRIVE 0 - 255 133
S031 G DRIVE 0 - 255 106
S032 B DRIVE 0 - 255 72
S033 (Not display) 0 - 255 0
S034 (Not display) 0 - 255 0
S035 (Not display) 0 - 255 0
S036 (Not display) 0 - 255 0
S037 (Not display) 0 - 255 0
S038 (Not display) 0 - 255 0
S039 ILA COM 0 - 1 0
Item No. Item name Variable range Setting value
T001 IN LEVEL 0 - 255 0
T002 LOW SEP 0 - 255 0
T003 HIGH SEP 0 - 255 0
T004 AFC 0 - 255 0
T005 (Not display) 0 - 255 0
T006 ATT V ON 0 - 1 0
T007 ATT U ON 0 - 1 0
T008 ATT C ON 0 - 1 0
T009 (Not display) 0 - 255 0
T010 (Not display) 0 - 255 0
4.6.3 PANEL CONTOROL SYSTEM SETTING (*Fixed values)
Item No. Item name Variable range Setting value
P001 TM HOR H 00 - FF 00
P002 TM HOR L 00 - FF 00
P003 TM MIN 00 - FF 00
P004 TEMP 0 - 255 0
P005 (Not display) 0 - 255 0
P006 (Not display) 0 - 255 0
P007 (Not display) 0 - 255 0
P008 (Not display) 0 - 255 0
P009 (Not display) 0 - 255 0
P010 (Not display) 0 - 255 0
4.6.4 DRIVE SYSTEM SETTING (*Fixed values)
Item No. Item name Variable range Setting value
D001 SLV GN 00 - 3F 15
D002 SLVH GN 00 - 3F 12
D003 SLH GN 00 - 3F 15
D004 SLV Pf 00 - 03 01
D005 SLH Pf H 00 - 01 01
D006 SLH Pf L 00 - 03 01
D007 SL EGCON 00 - 3F 10
D008 SL EGONF 00 - 01 01
D009 SL CRGON 00 - 3F 09
D010 SL CRGON 00 - 01 01
D011 SL ON OF 00 - 01 01
D012 SV GN 00 - 3F 0A
D013 SVH GN 00 - 3F 09
D014 SH GN 00 - 3F 0B
D015 SV Pf 00 - 03 01
D016 SV PfH 00 - 01 01
D017 SV PfL 00 - 03 01
D018 SYL CON 00 - 3F 30
D019 SYL CONF 00 - 01 01
1-20 (No.YA360)
Item No. Item name Variable range Setting value
D020 SYH CON 00 - 3F 00
D021 SYH CONF 00 - 01 01
D022 SC CON 00 - 3F 1A
D023 SC CNONF 00 - 01 01
D024 SPM BLC 00 - 3F 00
D025 SPM BLCO 00 - 01 01
D026 SLIM 00 - 3F 30
D027 SLIMONF 00 - 01 01
D028 SCRG 00 - 3F 09
D029 SRGONF 00 - 01 01
D030 S ONF 00 - 01 01
D031 pb GN 00 - 3F 15
D032 pb PfH 00 - 01 01
D033 pb PfL 00 - 03 00
D034 pb CRG 00 - 3F 10
D035 pb CRGON 00 - 01 01
D036 pb ONF 00 - 01 01
D037 pr GN 00 - 3F 15
D038 pr PfH 00 - 01 01
D039 pr PfL 00 - 03 00
D040 pr CRG 00 - 3F 10
D041 pr CRGON 00 - 01 01
D042 pr ONF 00 - 01 01
D043 ENH ONF 00 - 01 01
D044 (Not display) 00 - FF 00
D045 (Not display) 00 - FF 00
D046 (Not display) 00 - FF 00
D047 (Not display) 00 - FF 00
D048 (Not display) 00 - FF 00
D049 (Not display) 00 - FF 00
D050 (Not display) 00 - FF 00
D051 (Not display) 00 - FF 00
D052 (Not display) 00 - FF 00
D053 (Not display) 00 - FF 00
D054 (Not display) 00 - FF 00
D055 (Not display) 00 - FF 00
D056 (Not display) 00 - FF 00
D057 (Not display) 00 - FF 00
D058 (Not display) 00 - FF 00
D059 (Not display) 00 - FF 00
D060 (Not display) 00 - FF 00
D061 (Not display) 00 - FF 00
D062 (Not display) 00 - FF 00
D063 (Not display) 00 - FF 00
D064 (Not display) 00 - FF 00
D065 (Not display) 00 - FF 00
D066 (Not display) 00 - FF 00
D067 (Not display) 00 - FF 00
D068 (Not display) 00 - FF 00
D069 (Not display) 00 - FF 00
Item No. Item name Variable range Setting value
D070 (Not display) 00 - FF 00
D071 (Not display) 00 - FF 00
D072 (Not display) 00 - FF 00
D073 (Not display) 00 - FF 00
D074 (Not display) 00 - FF 00
D075 (Not display) 00 - FF 00
D076 (Not display) 00 - FF 00
D077 (Not display) 00 - FF 00
D078 (Not display) 00 - FF 00
D079 (Not display) 00 - FF 00
D080 (Not display) 00 - FF 00
D081 (Not display) 00 - FF 00
D082 (Not display) 00 - FF 00
D083 (Not display) 00 - FF 00
D084 (Not display) 00 - FF 00
D085 (Not display) 00 - FF 00
D086 (Not display) 00 - FF 00
D087 (Not display) 00 - FF 00
D088 (Not display) 00 - FF 00
D089 (Not display) 00 - FF 00
D090 (Not display) 00 - FF 00
D091 (Not display) 00 - FF 00
D092 (Not display) 00 - FF 00
D093 (Not display) 00 - FF 00
D094 (Not display) 00 - FF 00
D095 (Not display) 00 - FF 00
D096 (Not display) 00 - FF 00
D097 (Not display) 00 - FF 00
D098 (Not display) 00 - FF 00
D099 (Not display) 00 - FF 00
D100 (Not display) 00 - FF 00
D101 (Not display) 00 - FF 00
D102 (Not display) 00 - FF 00
D103 (Not display) 00 - FF 00
D104 (Not display) 00 - FF 00
D105 (Not display) 00 - FF 00
D106 (Not display) 00 - FF 00
D107 (Not display) 00 - FF 00
D108 (Not display) 00 - FF 00
D109 (Not display) 00 - FF 00
D110 (Not display) 00 - FF 00
D111 (Not display) 00 - FF 00
D112 (Not display) 00 - FF 00
D113 (Not display) 00 - FF 00
D114 (Not display) 00 - FF 00
D115 (Not display) 00 - FF 00
D116 (Not display) 00 - FF 00
D117 (Not display) 00 - FF 00
D118 (Not display) 00 - FF 00
D119 (Not display) 00 - FF 00
(No.YA360)1-21
Item No. Item name Variable range Setting value
D120 (Not display) 00 - FF 00
D121 (Not display) 00 - FF 00
D122 (Not display) 00 - FF 00
D123 (Not display) 00 - FF 00
D124 (Not display) 00 - FF 00
D125 (Not display) 00 - FF 00
D126 (Not display) 00 - FF 00
D127 (Not display) 00 - FF 00
D128 (Not display) 00 - FF 00
D129 (Not display) 00 - FF 00
D130 (Not display) 00 - FF 00
D131 (Not display) 00 - FF 00
D132 (Not display) 00 - FF 00
D133 (Not display) 00 - FF 00
D134 (Not display) 00 - FF 00
D135 (Not display) 00 - FF 00
D136 (Not display) 00 - FF 00
D137 (Not display) 00 - FF 00
D138 (Not display) 00 - FF 00
D139 (Not display) 00 - FF 00
D140 (Not display) 00 - FF 00
D141 (Not display) 00 - FF 00
D142 (Not display) 00 - FF 00
D143 (Not display) 00 - FF 00
D144 (Not display) 00 - FF 00
D145 (Not display) 00 - FF 00
D146 (Not display) 00 - FF 00
D147 (Not display) 00 - FF 00
D148 (Not display) 00 - FF 00
D149 (Not display) 00 - FF 00
D150 (Not display) 00 - FF 00
D151 (Not display) 00 - FF 00
D152 (Not display) 00 - FF 00
D153 (Not display) 00 - FF 00
D154 (Not display) 00 - FF 00
D155 (Not display) 00 - FF 00
D156 (Not display) 00 - FF 00
D157 (Not display) 00 - FF 00
D158 (Not display) 00 - FF 00
D159 (Not display) 00 - FF 00
D160 (Not display) 00 - FF 00
D161 (Not display) 00 - FF 00
D162 (Not display) 00 - FF 00
D163 (Not display) 00 - FF 00
D164 (Not display) 00 - FF 00
D165 (Not display) 00 - FF 00
D166 (Not display) 00 - FF 00
D167 (Not display) 00 - FF 00
D168 (Not display) 00 - FF 00
D169 (Not display) 00 - FF 00
Item No. Item name Variable range Setting value
D170 (Not display) 00 - FF 00
D171 (Not display) 00 - FF 00
D172 (Not display) 00 - FF 00
D173 (Not display) 00 - FF 00
D174 (Not display) 00 - FF 00
D175 (Not display) 00 - FF 00
D176 (Not display) 00 - FF 00
D177 (Not display) 00 - FF 00
D178 (Not display) 00 - FF 00
D179 (Not display) 00 - FF 00
D180 (Not display) 00 - FF 00
D181 (Not display) 00 - FF 00
D182 (Not display) 00 - FF 00
D183 (Not display) 00 - FF 00
D184 (Not display) 00 - FF 00
D185 (Not display) 00 - FF 00
D186 (Not display) 00 - FF 00
D187 (Not display) 00 - FF 00
4.6.5 MAIN CPU SYETEM SETTING (*Fixed values)
Item No. Item name Variable range Setting value
Z001 (Not display) 00 - FF 00
Z002 (Not display) 00 - FF 00
Z003 (Not display) 00 - FF 00
Z004 (Not display) 00 - FF 00
Z005 (Not display) 00 - FF 00
Z006 (Not display) 00 - FF 00
Z007 (Not display) 00 - FF 00
Z008 (Not display) 00 - FF 00
Z009 (Not display) 00 - FF 00
Z010 (Not display) 00 - FF 00
1-22 (No.YA360)
4.7 ADJUSTMENT PROCEDURE
4.7.1 VIDEO CIRCUIT
Item
625i A-D OFFSET
Measuring
instrument
Remote control unit
Test point Adjustment part Description
Signal generator
Disappears the color at both ends.
1125i (50Hz) BRIGHTNESS
Remote control unit
Signal generator
Set the 0% black part to be brightest.
1125i (50Hz) A-D OFFSET
Remote control unit
Signal generator
Minimize the red and blue noises in the upper half of the screen.
[1.ADJUST] S001: PREPARE (Adjustment setting mode change)
S008: 5i CB OF(625i cb offset) S009: 5i CR OF(625i cr offset)
S030: R DRIVE(Red drive) S031: G DRIVE(Green drive) S032: B DRIVE(Blue drive)
[1.ADJUST] S001: PREPARE (Adjustment setting mode change)
S012: HD BL(1125i brightness)
S030: R DRIVE(Red drive) S031: G DRIVE(Green drive) S032: B DRIVE(Blue drive)
[1.ADJUST] S001: PREPARE (Adjustment setting mode change)
S013: HD CB OF(1125i cb offset) S014: HD CR OF(1125i cr offset)
S030: R DRIVE(Red drive) S031: G DRIVE(Green drive) S032: B DRIVE(Blue drive)
(1) Receive a 625i component ramp pattern signal. (2) Set PICTURE MODE to "STANDARD". (3) Set ZOOM to "FULL". (4) Set COLOUR TEMP. to "NORMAL". (5) Select "1.ADJUST" from the SERVICE MODE. (6) Set < S030 > (R DRIVE), < S031 > (G DRIVE)
and < S032 > (B DRIVE) to "133".
(7) Set < S001 > (adjustment setting mode change)
to set "8" and it change to the 625i A-D offset adjustment setting mode.
(8) Adjust < S008 > (625i Cb offset) and < S009 >
(625i Cr offset) to lose the gap (red line, green line and blue line) which appears at both ends of a white part at the centre of the screen.
(9) Set < S001 > to set "0" and it change to the
normal mode.
(10) Press the [MUTING] key to memoirze the set
value.
(1) Receive a 1125i (50Hz) gray scale pattern signal. (2) Set PICTURE MODE to "STANDARD". (3) Set ZOOM to "FULL". (4) Set COLOUR TEMP. to "NORMAL". (5) Select "1.ADJUST" from the SERVICE MODE. (6) Set < S030 > (R DRIVE), < S031 > (G DRIVE)
and < S032 > (B DRIVE) to "133".
(7) Set < S001 > (adjustment setting mode change)
to set the values "12" and it change to the 1125i black level adjustment setting mode.
(8) Adjust < S012 > (1125i brightness) to set the
0% black part in the upper half of the screen to be brightest.
(9) Set < S001 > to set "0" and it change to the
normal mode.
(10) Press the [MUTING] key to memoirze the set
value.
(1) Receive a 1125i (50Hz) 30% all white pattern
signal. (2) Set PICTURE MODE to "STANDARD". (3) Set ZOOM to "FULL". (4) Set COLOUR TEMP. to "NORMAL". (5) Select "1.ADJUST" from the SERVICE MODE. (6) Set < S030 > (R DRIVE), < S031 > (G DRIVE)
and < S032 > (B DRIVE) to "133". (7) Set < S001 > (adjustment setting mode change)
to set "13" and it change to the 1125i A-D offset
adjustment setting mode. (8) Adjust < S013 > (1125i Cb offset) to minimize
the blue noise in the upper half of the screen. (9) Set < S014 > (1125i Cr offset) to minimize the
blue noise in the upper half of the screen.
(10) Set < S001 > to set "0" and it change to the
normal mode.
(11) Press the [MUTING] key to memoirze the set
value.
(No.YA360)1-23
Item
SUB SCREEN A-D OFFSET
Set the 0% block part to be brightest.
VIDEO-1
<NO SIGNAL>
WHITE BALANCE (HIGHLIGHT)
Measuring instrument
Remote control unit
Signal generator
TV(RF)
<30% all white>
Remote control unit
Signal generator
Test point Adjustment part Description
[1.ADJUST] S001: PREPARE (Adjustment setting mode change)
(1) Set PICTURE MODE to "STANDARD". (2) Set ZOOM" to "FULL". (3) Set COLOUR TEMP. to "NORMAL".
(4) Set MULTI SCREEN to "2 pictures". S016: RT CB OF (Sub screen cb offset) S017: RT CR OF (Sub screen cr offset)
(5) Receive a PAL 30% all white pattern signal on
the right screen. At the same time, set the Left
screen in VIDEO-1 mode (No signal). (6) Select "1.ADJUST" from the SERVICE MODE. (7) Set < S030 > (R DRIVE), < S031 > (G DRIVE)
S030: R DRIVE(Red drive) S031: G DRIVE(Green drive) S032: B DRIVE(Blue drive)
and < S032 > (B DRIVE) to "133". (8) Set < S001 > (adjustment setting mode change)
to set "17" and it change to the sub screen A-
D offset adjustment setting mode. (9) Adjust < S016 > (Sub screen cb offset) to
minimize the blue noise in the upper half of the
screen.
If you select an adjustment item < S016 >,
then the screen automatically turn to twin
pictures mode.
(10) Adjust < S017 > (Sub screen cr offset) to
minimize the red noise in the upper half of the
screen.
(11) Readjust < S016 > and < S017 > to set the
upper half of the screen to be the blackest.
(12) Set < S001 > to set "0" and it change to the
normal mode.
(13) Press the [MUTING] key to memoirze the set
value.
[1.ADJUST] S030: R DRIVE (Red drive) S031: G DRIVE (Green drive) S032: B DRIVE (Blue drive)
(1) Receive a PAL 75% all white signal. (2) Set PICTURE MODE to "STANDARD". (3) Set ZOOM to "FULL". (4) Set COLOUR TEMP. to "NORMAL". (5) Select "1.ADJUST" from the SERVICE MODE. (6) Adjust to Keep one of < S030 > (Red drive),
< S031 > (Green drive) or < S032 > (Blue drive)
unchanged, then lower the other two so that the
all-white screen is equally white throughout.
NOTE:
Set one or more of < S030 >, < S031 >, and
< S032 > to "85".
(7) Check that white balance is properly tracked
from low light to high light. If the white balance
tracking is deviated, adjust to correct it. (8) Press the [MUTING] key to memoirze the set
value.
1-24 (No.YA360)
SECTION 5
SERVICE MENU
1.ADJUST
2.SELF_CHECK
3.I2C STOP
LOB OK FAN OK SYNC M:OK S:OK HD:NG TIM OK MSM OK DIGI 0000 MEM OK AVSW OK YC OK AIO OK TUN OK GCR NG 1 IP OK RGB OK 8 DVI OK HDMI OK
FAN OK ALM OK TMP OK ATP OK ASH OK
PNL OK MEM OK TMP OK AIO OK
TROUBLESHOOTING
5.1 SELF CHECK FEATURE
5.1.1 OUTLINE
This unit comes with the "Self check" feature, which checks the operational state of the circuit and displays/saves it during failure.Diagnosis is performed when power is turned on, and information input to the main microcomputer is monitored at all time.Diagnosis is displayed in 2 ways via screen display and LED flashes. Failure detection is based on input state of I
2
C bus and
the various control lines connected to the main microcomputer.
5.1.2 HOW TO ENTER THE SELF CHECK MODE
Before entering the SERVICE MODE, confirm that the setting of VCR/TV/ DVD switch is at the "TV" side. If the switches have not been properly set, you cannot enter the SERVICE MODE.
(1) Press the [INFORMATION] key and [MUTING] key
simultaneously, then enter the SERVICE MODE. (2) Press the [2] key SELF CHECK MODE. (3) Press the [RED (ZOOM)] key to enter Page 2 of the SELF
CHECK MODE.
*Use the [GREEN (3D SOUND)] key to toggle between
Page 1 and Page 2.
NOTE:
When a number key other than the [2] key is pressed in the SERVICE MODE screen, the other relevant screen may be displayed. This is not used in the SELF CHECK MODE. Press the
[MENU] key to return to the MAIN MENU SCREEN.
5.1.3 HOW TO EXIT THE SELF CHECK MODE To Save Failure History:
Turn off the power by unplugging the AC power cord plug when in the Self check display mode.
To Clear (Reset) Failure History:
Turn off the power by pressing the [POWER] key on the remote control unit when in the Self check display mode.
5.1.4 FAILURE HISTORY
Failure history can be counted up to 9 times for each item. When the number exceeds 9, display will remain as 9. Failure history will be stored in the memory unless it has been deleted.
NOTE:
Only SYNC (with/without sync signals) will be neither counted nor stored.
5.1.5 POINTS TO NOTE WHEN USING THE SELF CHECK FEATURE
In addition to circuit failures (abnormal operation), the following cases may also be iagnosed as "Abnormal" and displayed and counted as "NG".
(1) Temporary defective transmissions across circuits due to
pulse interruptions
(2) Misalignment in the on/off timing of power for I
2
C bus
(VCC) when turning on/off the main power. Diagnosis may be impeded if a large number of items are displayed as "NG". As such, start Self check check only after 3 seconds in the case of receivers and 5 seconds in the case of panels upon turning on the power. If recurrences are expected, ensure to clear (reset) the failure history and record the new diagnosis reults.
SERVICE MODE SCREEN
SERVICE MENU
1.ADJUST
2.SELF_CHECK
3.I2C STOP
SELF CHECK MODE SCREEN (Page 1)
LOB OK FAN OK SYNC M:OK S:OK HD:NG TIM OK MSM OK DIGI 0000 MEM OK AVSW OK YC OK AIO OK TUN OK GCR NG 1 IP OK RGB OK 8 DVI OK HDMI OK
Item
CHECK Normality=OK Abnormality=NG
SELF CHECK MODE SCREEN (Page 2)
FAN OK ALM OK TMP OK ATP OK ASH OK
PNL OK MEM OK TMP OK AIO OK
Item
* As "SYNC" is not counted, the number of failures not displayed.
CHECK Normality=OK Abnormality=NG
Fig.1
(No.YA360)1-25
5.1.6 DETAILS
Self check is performed for the following items:
< Page 1 of screen >
Detection item Display Detection content
Low bias line short protection
LOB Confirmation of operation of the low bais
(2.5V / 3.3V / 5V / 9V) protection circuit.
Q9801 , Q9822 [REGULATOR PWB]
Diagnosis
signal (line)
Detection timing
LB_PRO Detection starts 3 seconds after the
power is turned on. If error continues between 400ms the power is turned off.
Abnormal rise of temperature in audio circuit
FAN Confirmation of the temperature of
audio circuit.
TH6661
[ANALOG SIGNAL PWB]
SDA Detection starts 3 seconds after the
power is turned on.
If the temperture of 90°C is detected for
3 seconds the power is turned off.
Presence of sync signal SYNC Confirmation of presence of video
sync signal.
SDA Confirmation of presence of sync signal
in video signal. M : Main sync signal S : Sub sync signal HD : Component sync signal
[ANALOG SIGNAL PWB]
IC201
AC power input TIM Not used. --- ---
Main CPU
MSM Not used. --- ---
communication
Digital tuner DIGI Not used. --- ---
Main memory MEM Confirmation of reply of ACK signal
which uses I
2
C communication.
SDA Same as above.
IC7602 [DIGITAL SIGNAL PWB]
AV select switch AVSW Same as above.
, IC501 [ANALOG SIGNAL PWB]
IC301
3 dimensions YC
YC Not used. --- ---
SDA Same as above.
separator
Multi sound process AIO Not used. --- ---
RF tuner TUN Confirmation of reply of ACK signal
which uses I2C communication.
TU3001
[RECEIVER PWB]
SDA If it checks whenever I
is performed and no reply of ACK signal
an error will be counted.
Ghost reduction GCR Not used. --- ---
DIST process IP Confirmation of reply of ACK signal
which uses I
2
C communication.
IC3001 [DIGITAL SIGNAL PWB]
RGB process RGB Confirmation of reply of ACK signal
which uses I
IC3001
DVI (Digital communication)
DVI Not used. --- ---
Digital input HDMI Confirmation of reply of ACK signal
which uses I
2
C communication.
[DIGITAL SIGNAL PWB]
2
C communication.
SDA If it checks whenever I
is performed and no reply of ACK signal
an error will be counted.
SDA If it checks whenever I
is performed and no reply of ACK signal
an error will be counted.
SDA If it checks whenever I2C communication
is performed and no reply of ACK signal
an error will be counted.
2
C communication
2
C communication
2
C communication
1-26 (No.YA360)
< Page 2 of screen >
Detection item Display Detection content
Diagnosis
signal (line)
Detection timing
Fan lock FAN Not used. --- ---
Abnormal of operation of
ALM Not used. --- ---
PANEL
Abnormal rise of
TMP Not used. --- ---
temperature in PANEL
Abnormal rise of
ATP Not used. --- --­temperature in audio circuit
Short circuit detection of
ASH Not used. --- --­audio circuit
Panel communication PNL Not used. --- ---
Sub memory MEM Not used. --- ---
Temp. sensor TMP Not used. --- ---
Audio control AIO Confirmation of reply of ACK signal
which uses I
2
C communication.
IC6521 [ANALOG SIGNAL PWB]
SDA If it checks whenever I
is performed and no reply of ACK signal an error will be counted.
5.1.7 METHOD OF DISPLAY WHEN A RASTER IS NOT OUTPUT
In the state where a raster is not output by breakdown of the set, an error is displayed by blink of the POWER LED.
Type of error POWER LED flash cycle
Low bias line short protection Low luminance blue turnig on and off at 1 second intervals.
Abnormal rise of temperature in audio circuit High luminance blue turnig on and off at 0.1 second intervals.
2
C communication
< Explanation of operation >
If error is detected, the power is turned off. Shortly after a power is turned off, POWER LED will be blinked. Power cannot be turned on until the power cord takes out and inserts, after a power is turned off.
(No.YA360)1-27
Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY DISPLAY CATEGORY 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama-city, Kanagawa-prefecture, 221-8528, Japan
(No.YA360)
Printed in Japan
VPT
LT-37M60BU LT-37M60ZU
WIDE LCD PANEL TV INSTRUCTIONS 16:9 LCD TV BEDIENUNGSANLEITUNG TELEVISEUR A ECRAN LCD PANORAMIQUE MANUEL D’INSTRUCTIONS BREEDBEELD LCD TV GEBRUIKSAANWIJZING TELEVISOR CON PANEL LCD PANORÁMICO MANUAL DE INSTRUCCIONES TV LCD WIDESCREEN ISTRUZIONI TELEVISOR COM ECRÃ PANORÂMICO DE INSTRUÇÕES CRISTAL LÍQUIDO
ENGLISH
DEUTSCH
FRANÇAIS
NEDERLANDS
CASTELLANO
ITALIANO
PORTUGUÊS
LCT1952-001A-U
Loading...
+ 121 hidden pages