For detailed operations and information, refer to the INSTRUCTION MANUAL on the following
website:
Pour les opérations et les informations détaillées, reportez-vous au MANUEL D’INSTRUCTIONS sur
le site web suivant:
Para obtener más información y detalles sobre las operaciones, consulte el MANUAL DE
INSTRUCCIONES en el siguiente sitio web:
<http://www.jvc.net/cs/car/>
For customer Use:
Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet.
Retain this information for future reference.
Model No.
Serial No.
B5K-0663-10 [K]
Page 2
Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida
útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de
residuos)
Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser
desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final
de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento
adecuado a estos productos y a sus subproductos residuales correspondientes.
Póngase en contacto con su administración local para obtener información sobre el
punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación
de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos
perjudiciales en la salud y el medio ambiente.
Informação sobre a eliminação de pilhas
Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou
entidade autorizada para que a mesma seja devolvida ao fabricante ou importador.
A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao
mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
Supplier's Declaration of Conformity
Trade Name: JVC
Products: DIGITAL MEDIA RECEIVER
Model Name: KD-X470BHS/KD-X370BTS/KD-X37MBS/KD-X270BT/KD-SX26BT
Responsible Party: JVCKENWOOD USA CORPORATION
2201 East Dominguez Street, Long Beach, CA 90810, U.S.A.
PHONE: 310 639-9000
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
i
Page 3
IC (Industry Canada) Caution
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
Attention de ‘IC (Industrie Canada)
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage.
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Contains Bluetooth Module FCC ID: ZWY88112
IC ID: 12033A-88112
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
CAUTION
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at
least 20 cm or more away from person’s body.
ATTENTION
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices
d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit
être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain.
Para cumplimiento de la IFT:
“La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su
operación no deseada”
SOFTWARE LICENSE AGREEMENT
The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is
copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions
which Users shall follow in order to use the Licensed Software.
The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the
Product in which the "Licensed Software" is embedded.
The Licensed Software may include the software which has been licensed to the Licensor directly or
indirectly from any third party. In such case, some third parties require the Users to follow their conditions
for use separately from this Software License Agreement. Such software shall not be subject to this
Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided
separately below.
Article 1 General Provision
The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case
referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User.
(the country where the User bought the Product (hereinafter the "Country")
Article 2 License
1. The license granted under this Agreement shall be the right to use the Licensed Software in the
Product.
2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed
Software and any related documents, whether in whole or in part.
3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall
not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.
4. The User shall use the Licensed Software according to the directions described in the operation
manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright
Law or any other laws and regulations by applying whole or a part of the Licensed Software.
Article 3 Conditions for Grant of License
1. When the User transfers the Product, it may also transfer the license to use the Licensed Software
embedded in the Product (including any related materials, updates and upgrades) on condition that
no original, copies or related materials continue in the possession of the User, and that the User shall
cause the transferee to comply with this Software License Agreement.
2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code
analysis works in connection with the Licensed Software.
ii
Page 4
Article 4 Right pertaining to the Licensed Software
Any and all copyrights and other rights pertaining to the Licensed Software and related documents
shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or
sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be
entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any
related documents.
Article 5 Indemnification of Licensor
1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User
or any third party due to the exercise of the license granted to the User under this Agreement, unless
otherwise restricted by law.
2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with
certain objective of the Licensed Software.
Article 6 Liability to Third Party
If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any
other intellectual property right that was caused by the User's use of the Licensed Software, the User shall
settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any
inconvenience it may cause.
Article 7 Confidentiality
The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof
or any other information to be granted under this Agreement, as well as the conditions of this Agreement
as has not yet entered the public domain, and shall not disclose or divulge the same to any third party
without approval of the Licensor.
Article 8 Termination
In case the User falls under any of the events described in the following items, the Licensor may
immediately terminate this Agreement or claim that the User compensates for the damage incurred by the
Licensor due to such event:
(1) when the User violated any provision of this Agreement; or
(2) when a petition has been filed against the User for an attachment, provisional attachment,
provisional disposition or any other compulsory execution.
Article 9 Destruction of the Licensed Software
If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed
Software, any related documents and copies thereof within two (2) weeks from such date of termination.
Article 10 Protection of Copyright
1. The copyright and all the other intellectual property rights relating to the Licensed Software
shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the
ownership of the User.
2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the
copyright and other intellectual property rights.
Article 11 Export Restriction
1. It is prohibited to export the Licensed Software and any related documents outside the country
of the User (including transmission thereof outside the country of the User via Internet of other
communication tools).
2. The User shall understand that the Licensed Software shall be subject to the export restrictions
adopted by the country of User and any other countries.
3. The User shall agree that the software will be subject to any and all applicable international and
domestic laws (including the export control regulation of the country of User and any other countries,
and any restrictions concerning the end-users, the use by end-users and importing countries to be
provided by the country of User and any other countries, and any other governmental authorities).
Article 12 Miscellaneous
1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions
shall continue in force.
2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of
this Agreement shall be provided or settled upon good-faith consultation between the Licensor and
the User.
3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and
any dispute arising from, and relating to the rights and obligations under, this Agreement shall be
submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.
iii
Page 5
Important Notice concerning the Software
-jansson
Copyright (c) 2009-2012 Petri Lehtinen <petri@digip.org>
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software without restriction, including without
limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following
conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions
of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
-cJSON
Copyright (c) 2009 Dave Gamble
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software without restriction, including without
limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following
conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions
of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
-CMP
The MIT License (MIT)
Copyright (c) 2014 Charles Gunyon
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software without restriction, including without
limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following
conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions
of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
nanopb
Copyright (c) 2011 Petteri Aimonen <jpa at nanopb.mail.kapsi.fi>
This software is provided 'as-is', without any express or implied warranty. In no event will the authors be
held liable for any damages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including commercial applications,
and to alter it and redistribute it freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote
the original software. If you use this software in a product, an acknowledgment in the product
documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the
original software.
3. This notice may not be removed or altered from any source distribution.
iv
Page 6
sha2
AUTHOR: Aaron D. Gifford - http://www.aarongifford.com/
Copyright (c) 2000-2001, Aaron D. Gifford
All rights reserved.
You may obtain a copy of the license at
https://opensource.org/licenses/BSD-3-Clause
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
Posix
Copyright (c) 1990, 1993
The Regents of the University of California. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following
acknowledgement:
This product includes software developed by the University of California, Berkeley and its contributors.
4. Neither the name of the University nor the names of its contributors may be used to endorse or
promote products derived from this software without specific prior written permission.
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.
Developed at SunPro, a Sun Microsystems, Inc. business.
Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is
preserved.
Copyright (C) 1991-2, RSA Data Security, Inc. Created 1991. All rights reserved.
License to copy and use this software is granted provided that it is identified as the “RSA Data Security, Inc.
MD4 Message-Digest Algorithm” in all material mentioning or referencing this software or this function.
Copyright (c) 1995, 1996 Carnegie-Mellon University. All rights reserved.
Author: Chris G. Demetriou
Permission to use, copy, modify and distribute this software and its documentation is hereby granted,
provided that both the copyright notice and this permission notice appear in all copies of the software,
derivative works or modified versions, and any portions thereof, and that both notices appear in supporting
documentation.
CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN ITS “AS IS” CONDITION. CARNEGIE MELLON
DISCLAIMS ANY LIABILITY OF ANY KIND FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF
THIS SOFTWARE.
Carnegie Mellon requests users of this software to return to
Software Distribution Coordinator or Software.Distribution@
CS.CMU.EDU
School of Computer Science
Carnegie Mellon University
Pittsburgh PA 15213-3890
any improvements or extensions that they make and grant Carnegie the rights to redistribute these
changes.
License is also granted to make and use derivative works provided that such works are identified as
“derived from the RSA Data Security, Inc. MD4 Message-Digest Algorithm” in all material mentioning or
referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or
the suitability of this software for any particular purpose. It is provided “as is” without express or implied
warranty of any kind.
Copyright (c) 1993 Martin Birgmeier
All rights reserved.
You may redistribute unmodified or modified versions of this source code provided that the above
copyright notice and this and the following conditions are retained.
This software is provided “as is”, and comes with no warranties of any kind. I shall in no event be liable for
anything that happens to anyone/anything when using this software.
These notices must be retained in any copies of any part of this documentation and/or software.
v
Page 7
T-Kernel 2.0
This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum
(www.tron.org)
BSD-3-Clause
Copyright (c) 2000-2001, Aaron D. Gifford
All rights reserved.
You may obtain a copy of the license at
https://opensource.org/licenses/BSD-3-Clause
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
LFS Subsystem
Copyright The Regents of the University of California. All rights reserved.
You may obtain a copy of the license at
https://directory.fsf.org/wiki/License:BSD-4-Clause
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Accordo2 Player
Apache License
Licensed under the Apache License,
Version 2.0, January 2004(the “License”);
You may obtain a copy of the license at
http://www.apache.org/licenses/LICENSE-2.0
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
vi
Page 8
Installation/Connection
This section is for the professional installer.
For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
WARNING
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to
prevent a short circuit.
• To prevent short circuit:
– Insulate unconnected wires with vinyl tape.
– Be sure to ground this unit to the car’s chassis again after installation.
– Secure the wires with cable clamps and wrap vinyl tape around the wires that comes into contact with
metal parts to protect the wires.
CAUTION
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and shortly
after use of the unit. Metal parts such as the heat sink and enclosure become hot.
• Do not connect the wires of speakers to the car chassis or Ground wire (black), or connect them in
parallel.
• Connect speakers with a maximum power of more than 50 W. If the maximum power of the speakers is
lower than 50 W, change the
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to the
terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned on and off by the
ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working
properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old fuse with
one that has the same rating.
[AMPGAIN]
setting to avoid damaging the speakers.
Basic procedure
1 Remove the key from the ignition switch, then disconnect the
terminal of the car battery.
2 Connect the wires properly. See “Wiring connection” on page 3.
3 Install the unit to your car. See the following “Installing the unit
(in-dash mounting)”.
4 Connect the terminal of the car battery.
5 Press B SRC to turn on the power.
6 Detach the faceplate and reset the unit within 5 seconds. See “How to
reset” on page 4.
Installing the unit (in-dash mounting)
Hook on the top side
Dashboard of your car
Bend the appropriate tabs to hold the
sleeve firmly in place.
2
Page 9
Installing the unit (without mounting sleeve)
1 Remove the mounting sleeve and trim plate from the unit.
2 Align the holes in the unit (on both sides) with the vehicle
mounting bracket and secure the unit with screws (commercially
available).
Use only the specified screws.
Using wrong screws might damage
the unit.
Fuse (10 A)
Join the same color
wires together.
a Light blue/yellow: To the
steering wheel remote control
adapter
b Brown (not used)
c Blue: To power antenna
d Blue/white: To amplifier
e Blue/white: Remote
(12 V
f Orange/white: Illumination
g Yellow: Battery 12 V
h Red: Ignition 12 V
350 mA)
Factory wiring
harness (vehicle)
Custom wiring harness
(separately purchased)
Recommended connection
i Black: Ground
j Gray ª, Gray/black ·:
Front speaker (right)
k White ª, White/black ·:
Front speaker (left)
l Purple ª, Purple/black ·:
Rear speaker (right)
m Green ª, Green/black ·:
Rear speaker (left)
3
Page 10
Before Use
Basics (on faceplate)
IMPORTANT
• To ensure proper use, please read through this Guide before using
this product. It is especially important that you read and observe
Warnings and Cautions in this Guide.
• Please keep the Guide in a safe and accessible place for future
reference.
WARNING
Do not operate any function that takes your attention away from safe
driving.
CAUTION
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to
prevent accidents.
• Lower the volume before playing digital sources to avoid
damaging the speakers by the sudden increase of the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no
responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal
tools) inside the unit to prevent a short circuit.
• Depending on the types of cars, the antenna will automatically
extend when you turn on the unit with the antenna control wire
connected. Turn off the unit when parking at a low ceiling area.
*1 Only for illustration purpose.
KD-X270BT/
Volume knob
Detach button
AttachDetach How to reset
ToOn the faceplate
Turn on the power
Adjust the volumeTurn the volume knob.
Select a source
Change the display information*2
*2 One of the display information supports Music Synchronization Effect. The illumination color or brightness level of
the buttons changes and synchronizes with the music level.
KD-SX26BT
Press B SRC.
• Press and hold to turn off the power.
Press B SRC repeatedly.
Press
Display window*1
Auxiliary
input jack
USB input
terminal
KD-X270BT/
KD-SX26BT
Reset the unit
within 5 seconds
after detaching the
faceplate.
repeatedly.
4
Page 11
Getting Started
1
Cancel the demonstration
When you turn on the power for the first time (or
[YES]
), the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB”
1 Press the volume knob.
[YES]
is selected for the initial setup.
2 Press the volume knob again.
“DEMO OFF” appears.
2
Set the clock and date
1 Press and hold .
2 Turn the volume knob to select
To adjust the clock
3 Turn the volume knob to select
[CLOCK]
[CLOCKADJUST]
4 Turn the volume knob to make the settings, then press the knob.
Set the time in the order of “Hour” “Minute”.
5 Turn the volume knob to select
6 Turn the volume knob to select
To set the date
7 Turn the volume knob to select
[CLOCK FORMAT]
[12H] or [24H]
[DATESET]
8 Turn the volume knob to make the settings, then press the knob.
Set the date in the order of “Day” “Month” “Year”.
9 Press to exit.
To return to the previous setting item, press
[FACTORY RESET]
, then press the knob.
, then press the knob.
, then press the knob.
, then press the knob.
, then press the knob.
.
is set to
3
Set the basic settings
1 Press and hold .
2 Turn the volume knob to select an item (see the following table), then
press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press to exit.
To return to the previous setting item, press
[SYSTEM]
[KEY BEEP]
[FACTORY RESET]
[CLOCK]
[CLOCK DISPLAY]
[ENGLISH]
[ESPANOL]
[FRANCAIS]*
* Only for KD-X470BHS/KD-X370BTS/KD-X37MBS.
(Not applicable when 3-way crossover is selected.)
[ON]: Activates the keypress tone. ; [OFF]: Deactivates.
[YES]: Resets the settings to default (except the stored station). ;
[NO]: Cancels.
[ON]: The clock time is shown on the display even when the unit is
turned off. ; [OFF]: Cancels.
Select the display language for menu and music information if
applicable.
By default, [ENGLISH] is selected.
.
Default: [XX]
5
Page 12
HD Radio™ Tuner/Radio
USB/iPod
For KD-X470BHS, you can tune in to both conventional and HD Radio
broadcasts.
Search for a station or channel
1 Press B SRC repeatedly to select FM or AM.
2 For KD-X470BHS: Press and hold to select the tuning mode.
•
[HDSEEK]
•
: Search for HD Radio broadcast only.
[MANUALSEEK]
: Search for both conventional and HD Radio broadcasts.
3 Press S / T to search for a station or channel automatically.
(or)
Press and hold S / T until “M” flashes, then press repeatedly to
search for a station or channel manually.
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM.
For KD-X470BHS, you can store 18 channels for HD Radio.
Store a station or channel
While listening to a station or channel....
Press and hold one of the number buttons (1 to 6).
(or)
1 Press and hold the volume knob until “PRESETMODE” flashes.
2 Turn the volume knob to select a preset number, then press the knob.
“MEMORY” appears once the station or channel is stored.
Select a stored station or channel
Press one of the number buttons (1to6).
(or)
1 Press .
2 For KD-X470BHS: Turn the volume knob to select
press the knob.
3 Turn the volume knob to select a preset number, then press the knob.
[PRESETLIST]
, then
Selectable source:
• KD-X470BHS/KD-X370BTS/KD-X37MBS: USB/iPodUSB or iPodBT
• KD-X270BT/KD-SX26BT: USB
Start playback
The source changes automatically and playback starts when you attach a
device (USB device/ iPod/iPhone) to the USB input terminal.
ToOn the faceplate
Reverse/Fast-forward
Select a file
Select a folder
Repeat play
Random play
Press and hold S / T.
Press S / T.
Press 2 J / 1 K.
Press 4 repeatedly.
Press 3 repeatedly.
6
Page 13
Menu Settings
1 Press and hold to enter menu settings.
2 Turn the volume knob to select an item, then press the knob.
3 Repeat step 2 until the desired item is selected/activated.
4 Press to exit.
To return to the previous setting item, press
• Refer to the INSTRUCTION MANUAL on the following website for the
detailed explanation of each item: <http://www.jvc.net/cs/car/>
• The availability of each item vary depending on the model.
6 Repeat step 4 and step 5 to set color for other zones.
7 Press to exit.
Other Information
[DAYCOLOR]
: Color changes at
[ALLZONE]
is selected
or
/
1 Press and hold to enter menu settings.
2 Turn the volume knob clockwise to select
3 Press the volume knob if
[PRESET]
4 Turn the volume knob to choose a zone (
then press the knob.
[COLOR]
is shown on the display.
[ALL ZONE], [ZONE 1], [ZONE 2]
8
, then press the knob.
),
For playback operations of AUX, Spotify, Pandora®, SiriusXM® Radio,
AMAZON ALEXA sources, refer to the INSTRUCTION MANUAL on the
following website: <http://www.jvc.net/cs/car/>
• The availability of each source vary depending on the model.
Note for specifications
Bluetooth Frequency Range:
2.402 GHz — 2.480 GHz
Bluetooth RF Output Power (E.I.R.P.):
+4 dBm (MAX), Power Class 2
Speaker Impedance:
4 Ω — 8 Ω
Operating Voltage:
12 V DC car battery
Page 15
Bluetooth®
• Depending on the Bluetooth version, operating system and the
firmware version of your mobile phone, Bluetooth features may not
work with this unit.
• Be sure to turn on the Bluetooth function of the device to make the
following operations.
• Signal conditions vary depending on the surroundings.
Connect the microphone
Connect the supplied microphone to the mirophone input terminal or
microphone input jack on the rear panel.
(B) “[Device Name]” Press the volume knob to start pairing.
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code
“0000” into the Bluetooth device.
• If only “PAIRING” appears, operate the Bluetooth device to confirm
pairing.
“PAIRING COMPLETED” appears when pairing is completed and “
up when the Bluetooth connection is established.
“VOL–YES” “BACK–NO”
” will light
Answer a call
Press or the volume knob.
• To adjust the phone volume
• To end a call, press and hold or the volume knob.
[00]
to
[35]
, turn the volume knob.
Adjust the
microphone
angle
Secure using cord
clamps (not supplied)
if necessary.
Pair and connect a Bluetooth device for the first time
1 Press B SRC to turn on the unit.
2 Search and select the name of your receiver (“KD-X470BHS”/
“KD-X370BTS”/“KD-X37MBS”/“KD-X270BT”/“KD-SX26BT”) on the
Bluetooth device.
3 Perform (A) or (B) depending on what appears on the display.
For some Bluetooth devices, pairing sequence may vary from the steps
described below.
(A) “[Device Name]” “XXXXXX” is a 6-digit passkey randomly generated during each pairing.
Ensure that the passkeys appear on the unit and Bluetooth device
are the same.
Press the volume knob to confirm the passkey.
Operate the Bluetooth device to confirm the passkey.
“XXXXXX” “VOL–YES” “BACK–NO”
Audio player via Bluetooth
1 Press B SRC repeatedly to select BTAUDIO.
• For KD-X270BT/KD-SX26BT: Pressing enters BT AUDIO directly.
2 Operate the audio player via Bluetooth to start playback.
ToOn the faceplate
Play back/pausePress the volume knob.
Select group or folder
Reverse skip/Forward skip
Reverse/Fast-forward
Repeat play
Random play
Press 2 J / 1 K.
Press S / T.
Press and hold S / T.
Press 4 repeatedly.
Press 3 repeatedly.
9
Page 16
Installation/Connexion
Cette section est réservée aux installateurs professionnels.
Pour des raison de sécurité, laissez le travail de câblage et de montage des professionnels. Consultez
votre revendeur autoradio.
MISE EN GARDE
• L’appareil peut uniquement être utilisé avec une alimentation de 12 V CC, à masse négative.
• Déconnectez la borne négative de la batterie avant le câblage et le montage.
• Ne connectez pas le fil de batterie (jaune) et le fil d’allumage (rouge) au châssis de la voiture ou au fil de masse
(noir) pour éviter les courts-circuits.
• Pour éviter les courts-circuits:
– Isolez les fils non connectés avec du ruban adhésif.
– Assurez-vous de raccorder de nouveau la mise à la masse de cet appareil au châssis de la voiture après
l’installation.
– Fixez les câbles avec des serre-câbles et enrouler un ruban de vinyle autour des câbles qui entrent en contact
avec des pièces métalliques pour protéger les câbles.
AVERTISSEMENT
• Installez cet appareil dans la console de votre véhicule. Ne touchez pas les parties métalliques de cet appareil
pendant ou juste après son utilisation. Les parties métalliques, comme le dissipateur de chaleur et le boîtier,
deviennent chaudes.
• Ne connectez pas les fils
• Connectez des enceintes avec une puissance maximum de plus de 50 W. Si la puissance maximum des enceintes
est inférieure à 50W, changez le réglage
• Montez l’appareil avec un angle de moins de 30º.
• Si le faisceau de fils de votre véhicule ne possède pas de borne d’allumage, connectez le fil d’allumage (rouge) à la
borne du boîtier de fusible de votre véhicule qui offre une alimentation de 12 V CC et qui se met en et hors service
avec la clé de contact.
• Gardez tous les câbles à l’écart des dissipateurs thermiques.
• Après avoir installé l’appareil, vérifiez si les lampes de frein, les indicateurs, les clignotants, etc. de la voiture
fonctionnent correctement.
• Si un fusible saute, assurez-vous d’abord que les câbles ne touches pas le châssis de la voiture puis remplacez le
vieux fusible par un nouveau de même valeur.
des l’enceintes au châssis de la voiture, au fil de masse (noir) ou en parallèle.
[AMPGAIN]
pour éviter d’endommager les enceintes.
Procédure de base
1 Retirez la clé de contact, puis déconnectez la borne de la batterie de la
voiture.
2 Connectez les fils correctement. Voir “Connexions” à la page3.
3 Installez l’appareil dans votre voiture. Reportez-vous à “Installation de
l’appareil (montage encastré)” ci-après.
4 Connectez la borne de la batterie de la voiture.
5 Appuyez sur B SRC pour mettre l’appareil sous tension.
6 Détachez la façade et réinitialisez l’appareil avant 5 secondes. Voir
“Comment réinitialiser” à la page4.
Installation de l’appareil (montage encastré)
Crochet sur le côté
supérieur
Tableau de bord de votre voiture
Tordez les languettes appropriées pour
maintenir le manchon en place.
2
Page 17
Installation de l’appareil (sans le manchon de montage)
1 Retirez le manchon de montage et la plaque de garniture de l’appareil.
2 Alignez les entailles de l’appareil (des deux côtés) avec le support de
montage du véhicule et fixez l’appareil avec les vis (en vente dans le
commerce).
Connexions
Borne de l’antenne
Tableau de bord
du véhicule
Retrait de l’appareil
Liste de pièces (fourni)
(A) Façade (×1)
(B) Plaque de garniture (×1)
(C) Manchon de montage (×1)
(D) Faisceau de fils (×1)
(E) Clé d’extraction (×2)
N’utiliser que les vis spécifiés.
L’utilisation de vis incorrects peut
endommager l’appareil.
Fusible (10 A)
Joignez les fils de même
couleur ensemble.
a Bleu clair/jaune: À l’adaptateur
de télécommande volant
b Marron (non utilisé)
c Bleu: À l’antenne alimentée
d Bleu/blanc: À l’amplificateur
e Bleu/blanc: Télécommande (12V 350mA)
f Orange/blanc: Éclairage
g Jaune: Batterie 12 V
h Rouge: Allumage 12V
i Noir: Masse
j Gris ª, Gris/Noir ·:
Enceinte avant (droite)
Faisceau de
câbles de l’usine
(véhicule)
Faisceau de fils personnalisé
(vendu séparément)
Connexion recommandée
k Blanc ª, Blanc/Noir ·:
Enceinte avant (gauche)
l Violet ª, Violet/Noir ·:
Enceinte arrière (droite)
m Ve rt ª, Vert/Noir ·:
Enceinte arrière (gauche)
3
Page 18
Avant l’utilisation
Fonctionnement de base (sur la façade)
IMPORTANTES
• Pour utiliser correctement l’appareil, veuillez lire ce Guide complément
avant de l’utiliser. Il est particulièrement important que vous lisiez et
acceptiez les avertissements et les précautions de ce Guide.
• Veuillez garder ce Guide dans un endroit sûr et accessible pour une
utilisation future.
MISE EN GARDE
N’utilisez aucune fonction qui risque de vous distraire de la conduite sure
de votre véhicule.
AVERTISSEMENT
Réglage du volume:
• Ajustez le volume de façon à pouvoir entendre les sons extérieurs à la
voiture afin d’éviter tout risque d’accident.
• Réduisez le volume avant de reproduire des sources numériques afin
d’éviter d’endommager les enceintes par la soudaine augmentation du
niveau de sortie.
Généralités:
• Éviter d’utiliser le périphérique extérieur s’il peut gêner une conduite en
toute sécurité.
• Assurez-vous que toutes les données importantes ont été sauvegardées.
Nous ne pouvons pas être tenu responsable pour toute perte des
données enregistrées.
• Veuillez faire en sorte de ne jamais mettre ou laisser d’objets métalliques
(tels que des pièces ou des outils) dans l’appareil, afin d’éviter tout
risque de court-circuit.
• En fonction du type de voiture, l’antenne s’étendra automatiquement
quand vous mettrez l’appareil sous tension si le câble de commande
d’antenne est connecté. Mettez l’appareil hors tension quand vous vous
garez dans un parking avec un plafond bas.
*1 Uniquement à des fins d’illustration.
Bouton de volume
Touche de détachement
AttachezDétachez Comment réinitialiser
PourSur la façade
Mettez l’appareil sous tension
Ajustez le volumeTournez le bouton de volume.
Sélectionner la source
Changez l’information sur
l’affichage*2
*2 Une des informations de l’affichage prend en charge l’effet de synchronisation musicale. La couleur d’éclairage ou le niveau
de luminosité des touches change et est synchronisé avec le niveau de la musique.
KD-X270BT/
KD-SX26BT
Appuyez sur
• Maintenez la touche enfoncée pour mettre
l’appareil hors tension.
Appuyez répétitivement sur
Appuyez répétitivement sur
Fenêtre d’affichage*1
Réinitialisez l’appareil en
moins de 5 secondes
après avoir détaché la
façade.
B SRC.
B SRC.
Prise d’entrée
auxiliaire
Prise d’entrée
USB
KD-X270BT/
KD-SX26BT
.
4
Page 19
Prise en main
1
Annulez la démonstration
Quand vous mettez l’appareil sous tension pour la première fois (ou que
[FACTORY RESET]
“PRESS” “VOLUME KNOB ”
1 Appuyez sur le bouton de volume.
[YES]
2 Appuyez de nouveau sur le bouton de volume.
“DEMO OFF” apparaît.
2
1 Maintenez enfoncée .
2 Tournez le bouton de volume pour choisir
bouton.
Pour ajuster l’horloge
3 Tournez le bouton de volume pour choisir
le bouton.
4 Tournez le bouton de volume pour faire les réglages, puis appuyez sur le
bouton.
Réglez l’heure dans l’ordre “Heures”
5 Tournez le bouton de volume pour choisir
le bouton.
6 Tournez le bouton de volume pour choisir
le bouton.
Pour régler la date
7 Tournez le bouton de volume pour choisir
bouton.
8 Tournez le bouton de volume pour faire les réglages, puis appuyez sur le
bouton.
Réglez la date dans l’ordre “Jour”
9 Appuyez sur pour quitter.
Pour retourner à l’option de réglage précédente, appuyez sur
est réglé sur
est choisi pour le réglage initial.
[YES]
), l’affichage montre: “CANCEL DEMO”
Réglez l’horloge et la date
“Mois” “Année”.
“Minutes”.
[CLOCK]
, puis appuyez sur le
[CLOCKADJUST]
[CLOCK FORMAT]
[12H] ou [24H]
[DATESET]
, puis appuyez sur le
, puis appuyez sur
, puis appuyez sur
, puis appuyez sur
.
3
Faites les réglages de base
1 Maintenez enfoncée .
2 Tournez le bouton de volume pour sélectionner un élément (voir le tableau
suivant), puis appuyez sur le bouton.
3 Répétez l’étape 2 jusqu’à ce que l’élément souhaité soit sélectionné ou
activé.
4 Appuyez sur pour quitter.
Pour retourner à l’option de réglage précédente, appuyez sur
[SYSTEM]
[KEY BEEP]
[FACTORY RESET][ YES]:Réinitialise les réglages aux valeurs par défaut (sauf la station
[CLOCK]
[CLOCK DISPLAY]
[ENGLISH]
[ESPANOL]
*
[FRANCAIS]
* Uniquement pour le KD-X470BHS/KD-X370BTS/KD-X37MBS.
(Non applicable quand la transition 3 voies est sélectionnée.)
[ON]:Met en service la tonalité des touches.;
[OFF]:Met hors service la fonction.
mémorisée).;
[ON]:L’horloge apparaît sur l’affichage même quand l’appareil est hors
tension.;
Sélectionnez la langue d’affichage pour le menu et l’information sur le
morceau si elle est disponible.
Par défaut,
[NO]:Annulation.
[OFF]:Annulation.
[ENGLISH] est sélectionné.
.
Défaut: [XX]
5
Page 20
Tuner HD Radio™/Radio
Pour KD-X470BHS, vous pouvez accorder à la fois les émissions conventionnelles
et HD Radio.
Recherche d’une station ou d’un canal
1 Appuyez répétitivemenent sur B SRC pour sélectionner FM ou AM.
2 Pour KD-X470BHS: Maintenez enfoncé pour choisir le monde
d’accord.
•
[HDSEEK]
•
3 Appuyez sur S / T pour rechercher une station ou un canal
automatiquement.
(ou)
Maintenez en enfoncé S / T jusqu’à ce que “M” clignote, puis
appuyez répétitivement dessus pour rechercher une station ou un canal
manuellement.
Réglages en mémoire
Vous pouvez mémoriser un maximum de 18 stations pour FM et de 6 stations
pour AM.
Pour le KD-X470BHS, vous pouvez mémoriser 18 canaux pour HD Radio.
Mémorisation d’une station ou un canal
Lors de l’écoute d’une station ou d’un canal...
Maintenez enfoncée une des touches numériques (1 à 6).
(ou)
1 Maintenez enfoncé le bouton de volume jusqu’à ce que “PRESETMODE”
clignote.
2 Tournez le bouton de volume pour choisir un numéro de préréglage, puis
appuyez sur le bouton.
“MEMORY” apparaît une fois que la station ou le canal est mémorisé.
Sélection d’une station ou d’un canal mémorisé
Appuyez sur l’une des touches numériques (1 à 6).
(ou)
1 Appuyez sur .
2 Pour KD-X470BHS: Tournez le bouton de volume pour choisir
puis appuyez sur le bouton.
3 Tournez le bouton de volume pour choisir un numéro de préréglage, puis
appuyez sur le bouton.
6
: Recherchez uniquement une station HD Radio.
[MANUALSEEK]
: Faites une recherche d’émissions ordinaires et HD Radio.
[PRESETLIST]
USB/iPod
Source sélectionnable:
• KD-X470BHS/KD-X370BTS/KD-X37MBS: USB/iPod USB ou iPod BT
• KD-X270BT/KD-SX26BT: USB
Démarrez la lecture
La source change automatiquement et la lecture démarre quand vous connectez
un périphérique (périphérique USB/ iPod/iPhone) à la prise d’entrée USB.
PourSur la façade
Recherche rapide vers
l’arrière/vers l’avant
Sélectionnez un fichier
Sélectionnez un dossier
Lecture répétée
Lecture aléatoire
,
Maintenez enfoncée
Appuyez sur
Appuyez sur 2
Appuyez répétitivement sur 4
Appuyez répétitivement sur 3
S / T.
S / T.
J / 1 K.
.
.
Page 21
Réglages du menu
1
Maintenez enfoncée pour entrer en réglages du menu.
2
Tournez le bouton de volume pour choisir un élément, puis appuyez sur le
bouton.
3
Répétez l’étape 2 jusqu’à ce que l’élément souhaité soit sélectionné ou
activé.
4
Appuyez sur pour quitter.
Pour retourner à l’option de réglage précédente, appuyez sur
• Reportez-vous au MANUEL D’INSTRUCTIONS sur les sites web suivant pour une
explication détaillée de chaque élément: <http://www.jvc.net/cs/car/>
• La disponibilité de chaque élément varient en fonction du modèle.
apparaît. (Sélectionnable uniquement quand
est choisi à l’étape 4.)
[COLOR49]
: La couleur que vous avez créée pour
[NIGHTCOLOR]
apparaît.
à
[COLORFLOW03]
: Le motif de couleur sélectionné
: La couleur change à
Autres informations
Pour les opérations de lecture des sources AUX, Spotify, Pandora®, SiriusXM®
Radio, AMAZON ALEXA , reportez-vous au MANUEL D’INSTRUCTIONS sur le site
web suivant: <http://www.jvc.net/cs/car/>
• La disponibilité de chaque source varie en fonction du modèle.
Remarque pour les spécifications
Plage de fréquencesBluetooth:
2,402 GHz — 2,480 GHz
Puissance de sortie RF Bluetooth (E.I.R.P.):
+4 dBm (MAX), Classe d’alimentation 2
Impédance d’enceinte:
4Ω—8Ω
Tension de fonctionnement:
Batterie de voiture 12 V CC
[DAYCOLOR]
/
[ALLZONE]
8
Page 23
Bluetooth®
• En fonction de la version Bluetooth, du système d’exploitation et de la
version du micrologiciel de votre téléphone portable, la fonction Bluetooth
peut ne pas fonctionner avec cet appareil.
• Assurez-vous d’activer la fonction Bluetooth du périphérique pour réaliser les
opérations suivantes.
• La condition du signal varie en fonction de l’environnement.
Connectez le microphone
Branchez le microphone fourni sur la prise d’entrée du microphone ou sur le
connecteur d’entrée femelle sur le panneau arrière.
Ajustez
l’angle du
microphone
Faites le pairage et connectez un périphérique
Bluetooth pour la première fois
1 Appuyez sur B SRC pour mettre l’appareil sous tension.
2 Recherchez et sélectionnez le nom de votre récepteur (“KD-X470BHS”/
“KD-X370BTS”/“KD-X37MBS”/“KD-X270BT”/“KD-SX26BT”) sur le
périphérique Bluetooth.
3 Réalisez (A) ou (B) en fonction de ce qui apparait sur l’affichage.
Pour certains périphériques Bluetooth, la séquence de pairage peut varier en
fonction des étapes décrites ci-dessous.
(A) “[Nom du périphérique]” “XXXXXX” “VOL–YES” “BACK–NO”
“XXXXXX” est un code à 6 chiffres généré aléatoirement pendant chaque
pairage.
Assurez-vous que les codes qui apparaissent sur l’appareil et le
périphérique Bluetooth sont les mêmes.
Appuyez sur le bouton de volume pour valider le code.
Utilisez le périphérique Bluetooth pour valider le code.
Fixez si nécessaire
en utilisant des
serre-câbles
(non fourni).
(B) “[Nom du périphérique]” “VOL–YES” “BACK–NO”
Appuyez sur le bouton de volume pour démarrer le pairage.
• Si “PAIRING” “PIN 0000” défile sur l’affichage, entrez le code PIN “0000”
sur le périphérique Bluetooth.
• Si seul “PAIRING” apparaît, utilisez le périphérique Bluetooth pour
confirmer le pairage.
“PAIRING COMPLETED” apparaît quand le pairage est terminé et “
quand la connexion Bluetooth est établie.
” s’allume
Répondre à un appel
Appuyez sur ou sur le bouton de volume.
• Pour ajuster le volume du téléphone entre
volume.
• Pour terminer un appel, maintenez enfoncé
[00]
et
[35]
, tournez le bouton de
ou le bouton de volume.
Lecteur audio via Bluetooth
1 Appuyez répétitivement sur B SRC pour sélectionner BT AUDIO.
• Pour KD-X270BT/KD-SX26BT: Appuyer sur
à BT AUDIO.
2 Commandez le lecteur audio via Bluetooth pour démarrer la lecture.
PourSur la façade
Lecture/pauseAppuyez sur le bouton de volume.
Choisissez un groupe ou un
dossier
Saut vers l’arrière/saut vers l’avant
Recherche rapide vers l’arrière/
vers l’avant
Lecture répétée
Lecture aléatoire
Appuyez sur 2
Appuyez sur
Maintenez enfoncée
Appuyez répétitivement sur 4
Appuyez répétitivement sur 3
permet d’accéder directement
J / 1 K.
S / T.
S / T.
.
.
9
Page 24
Instalación/Conexión
Esta sección es para los instaladores profesionales.
Para fines de seguridad, deje que un profesional realice el cableado y el montaje. Consulte con un
distribuidor de productos de audio para automóviles.
ADVERTENCIA
• La unidad puede utilizarse solamente con una fuente de alimentación de 12 V CC con negativo a masa.
• Desconecte el terminal negativo de la batería antes de realizar el cableado y el montaje.
• Para evitar un cortocircuito, no conecte el cable de la batería (amarillo) ni el cable de encendido (rojo) al chasis del
vehículo o cable de conexión a masa (negro).
• Para evitar cortocircuitos:
– Utilice una cinta de vinilo para aislar los cables no conectados.
– Asegúrese de volver a conectar a masa esta unidad al chasis del automóvil después de la instalación.
– Para proteger los cables, asegúrelos con abrazaderas de cables y con una cinta de vinilo, enrolle los cables que
entran en contacto con partes metálicas.
PRECAUCIÓN
• Instale esta unidad en la consola de su vehículo. No toque las partes metálicas de la unidad durante o un poco
después del uso de la unidad. Las partes metálicas, tales como el disipador de calor o la carcasa, pueden estar muy
calientes.
• No conecte los cables
• Conecte altavoces con una potencia máxima de más de 50 W. Si la potencia máxima de los altavoces es inferior a
50 W, cambie el ajuste
• Monte la unidad a un ángulo de menos de 30˚.
• Si el mazo de conductores de su vehículo no dispone de terminal de encendido, conecte el cable de encendido
(rojo) al terminal de la caja de fusibles del vehículo, el cual suministrará una alimentación de 12 V CC y podrá
conectarse y desconectarse mediante la llave de encendido.
• Mantenga todos los cables alejados de las partes metálicas disipadoras de calor.
• Después de instalar la unidad, compruebe que las lámparas de freno, las luces intermitentes, el limpiaparabrisas,
etc. funcionen satisfactoriamente.
• Si se funde el fusible, en primer lugar asegúrese de que los cables no estén en contacto con el chasis del vehículo y,
a continuación, reemplace el fusible usado por otro del mismo régimen.
de los altavoces al chasis del vehículo, al cable de conexión a masa (negro) o en paralelo.
[AMPGAIN]
para evitar daños en los mismos.
Procedimiento básico
1 Quite la llave del interruptor de encendido; después, desconecte el
terminal
2 Conecte los cables correctamente. Consulte “Conexión del cableado” en la
página 3.
3 Instale la unidad en su automóvil. Consulte lo siguiente “Instalación de la
unidad (montaje en el tablero)”.
4 Conecte el terminal de la batería del automóvil.
5 Pulse B SRC para encender la unidad.
6 Extraiga la placa frontal y reinicialice la unidad en menos de 5 segundos.
Consulte “Cómo reinicializar” en la página 4.
Instalación de la unidad (montaje en el tablero)
de la batería del automóvil.
Gancho en el
lado superior
Salpicadero del automóvil
Doble las lengüetas apropiadas para retener
firmemente la manga en su lugar.
2
Page 25
Instalación de la unidad (sin manguito de montaje)
1 Retire de la unidad, el manguito de montaje y la placa embellecedora.
2 Alinee los orificios de la unidad (en ambos lados) con la ménsula de
montaje del vehículo y asegure la unidad con los tornillos (disponibles
en el mercado).
Conexión del cableado
Terminal de la
antena
Salpicadero
del vehículo
Desmontaje de la unidad
Lista de piezas (suministradas)
(A) Placa frontal (×1)
(B) Placa embellecedora (×1)
(C) Manguito de montaje (×1)
(D) Mazo de conductores (×1)
(E) Herramienta de extracción (×2)
Utilice solo los tornillos
especificados. El uso de tornillos
incorrectos puede dañar la unidad.
Fusible (10 A)
Junte los cables del
mismo color.
a Luz azul/amarilla: Al adaptador
del mando a distancia del
volante de la dirección
b Marrón (sin utilizar)
c Azul: A la antena motriz
d Azul/blanco: Al amplificador
e Azul/blanco: Remoto (12V 350mA)
f Naranja/blanco: Iluminación
g Amarillo: Batería de 12 V
h Rojo: Encendido de 12 V
i Negro: Tierra
j Gris ª, Gris/negro ·:
Altavoz delantero (derecho)
Mazo de cables de
fábrica (vehículo)
Mazo de conductores
personalizado (adquirido
por separado)
Conexión recomendada
k Blanco ª, Blanco/negro ·:
Altavoz delantero (izquierdo)
l Púrpura ª, Púrpura/negro ·:
Altavoz trasero (derecho)
m Verde ª, Verde/negro ·:
Altavoz trasero (izquierdo)
3
Page 26
Antes del uso
Puntos básicos (en la placa frontal)
IMPORTANTE
• Antes de utilizar este producto y para asegurar su uso correcto, lea
esta guía por completo. En especial, lea y observe las Advertencias y
Precauciones incluidas en esta guía.
• Guarde la guía en un lugar seguro y accesible para futuras consultas.
ADVERTENCIA
No utilice ninguna función que pueda desviar su atención mientras está
conduciendo el vehículo.
PRECAUCIÓN
Ajuste del volumen:
• Ajuste el volumen a un nivel que le permita oír los ruidos del exterior
para impedir accidentes.
• Antes de reproducir fuentes digitales, baje el volumen para evitar que el
repentino aumento del nivel de salida cause daños a los altavoces.
General:
• Evite el uso de dispositivos externos cuando puedan afectar la
seguridad de conducción.
• Asegúrese de tener una copia de respaldo de todos los datos
importantes. No aceptamos responsabilidad alguna por la pérdida de
los datos grabados.
• Para evitar cortocircuitos, nunca coloque ni deje objetos metálicos (por
ejemplo, monedas o herramientas metálicas) dentro de la unidad.
• Dependiendo del tipo de vehículo, la antena se extiende
automáticamente cuando se enciende la unidad con el cable de control
de antena conectado. Apague la unidad cuando estacione en un lugar
con techo bajo.
*1 Solo para fines ilustrativos.
Rueda de volumen
Botón de liberación
FijarDesmontar Cómo reinicializar
ParaEn la placa frontal
Encender la unidad
Ajustar el volumenGire la rueda de volumen.
Seleccionar una fuente
Cambiar la información en
pantalla*2
*2 Una de las informaciones en pantalla admite el Efecto de sincronización de música. El color de iluminación o el nivel de brillo
de los botones cambia y se sincroniza con el nivel de música.
KD-X270BT/
KD-SX26BT
Pulse
• Pulse y mantenga pulsado para apagar la
unidad.
Pulse
Pulse
Ventanilla de visualización*1
Reinicialice la unidad en
menos de 5 segundos
después de haber
extraído la placa frontal.
B SRC.
B SRC repetidamente.
repetidamente.
Toma de
entrada auxiliar
Terminal de
entrada USB
KD-X270BT/
KD-SX26BT
4
Page 27
Procedimientos iniciales
1
Cancele la demostración
Cuando enciende la unidad por primera vez (o
[YES]
), en la pantalla se muestra: “CANCEL DEMO” “PRESS” “VOLUME KNOB”
1 Pulse la rueda de volumen.
Se selecciona
2 Pulse de nuevo la rueda de volumen.
Aparece “DEMO OFF”.
2
Ajuste del reloj y la fecha
1 Pulse y mantenga pulsado .
2 Gire la rueda de volumen para seleccionar
la rueda.
Para ajustar el reloj
3 Gire la rueda de volumen para seleccionar
pulse la rueda.
4 Gire la rueda de volumen para realizar los ajustes y, a continuación, pulse la
rueda.
Ajuste la hora en el orden de “Hora”
5 Gire la rueda de volumen para seleccionar
pulse la rueda.
6 Gire la rueda de volumen para seleccionar
pulse la rueda.
Para ajustar la fecha
7 Gire la rueda de volumen para seleccionar
pulse la rueda.
8 Gire la rueda de volumen para realizar los ajustes y, a continuación, pulse la
rueda.
Ajuste la fecha en el orden de “Día”
[YES]
para la configuración inicial.
9 Pulse para salir.
Para volver al elemento de ajuste anterior, pulse
[FACTORY RESET]
[CLOCK]
[CLOCKADJUST]
“Minutos”.
[CLOCK FORMAT]
[12H] o [24H]
[DATESET]
“Mes” “Año”.
está ajustado a
y, a continuación, pulse
y, a continuación,
y, a continuación,
y, a continuación,
y, a continuación,
.
3
Realice los ajustes básicos
1 Pulse y mantenga pulsado .
2 Gire la rueda de volumen para seleccionar un elemento (consulte la
siguiente tabla) y, a continuación, pulse la rueda.
3 Repita el paso 2 hasta que se seleccione o active el elemento deseado.
4 Pulse para salir.
Para volver al elemento de ajuste anterior, pulse
[SYSTEM]
[KEY BEEP]
[FACTORY RESET][ YES]:Se restablecen los ajustes predeterminados (excepto la emisora
[CLOCK]
[CLOCK DISPLAY]
[ENGLISH]
[ESPANOL]
*
[FRANCAIS]
* Sólo para KD-X470BHS/KD-X370BTS/KD-X37MBS.
(No aplicable si se ha seleccionado crossover de 3 vías.)
[ON]:Activa el tono de pulsación de teclas.; [OFF]:Se desactiva.
memorizada).;
[ON]:La hora del reloj siempre se visualiza en la pantalla cuando la unidad
está apagada.;
Seleccione el idioma de visualización para el menú y la información de la
música, si corresponde.
Por defecto, se selecciona
[NO]:Se cancela.
[OFF]:Se cancela.
[ENGLISH].
.
Predeterminado: [XX]
5
Page 28
Sintonizador HD Radio™/Radio
Para KD-X470BHS, puede sintonizar tanto transmisiones convencionales y
emisiones de HD Radio.
Busca una emisora o un canal de radio
1 Pulse B SRC repetidamente para seleccionar FM o AM.
2 Para KD-X470BHS: Pulse y mantenga pulsado para seleccionar el
modo de sintonización.
•
[HDSEEK]
•
3 Pulse S / T para la búsqueda automática de una emisora o un canal.
(o)
Pulse y mantenga pulsado S / T hasta que parpadee “M” y, a
continuación, pulse repetidamente para la búsqueda manual de una
emisora o un canal.
Ajustes en la memoria
Puede almacenar hasta 18 emisoras de FM y 6 emisoras de AM en la memoria.
Con KD-X470BHS, puede almacenar 18 canales de HD Radio.
Guarde una emisora o un canal
Mientras escucha una emisora o un canal....
Pulse y mantenga pulsado uno de los botones numéricos (1 a 6).
(o)
1 Pulse y mantenga pulsada la rueda de volumen hasta que “PRESETMODE”
parpadee.
2 Gire la rueda de volumen para seleccionar un número de preajuste y, a
continuación, pulse la rueda.
Aparece “MEMORY” una vez que la emisora o el canal esté almacenado.
Seleccione una emisora o canal guardado
Pulse uno de los botones numéricos (1a6).
(o)
1 Pulse .
2 Para KD-X470BHS: Gire la rueda de volumen para seleccionar
a continuación, pulse la rueda.
3 Gire la rueda de volumen para seleccionar un número de preajuste y, a
continuación, pulse la rueda.
: Busca sólo emisión de HD Radio.
[MANUALSEEK]
: Busca tanto emisiones convencionales como HD Radio.
[PRESETLIST]
USB/iPod
Fuente seleccionable:
• KD-X470BHS/KD-X370BTS/KD-X37MBS: USB/iPod USB o iPod BT
• KD-X270BT/KD-SX26BT: USB
Inicie la reproducción
La fuente cambia automáticamente y la reproducción se inicia al conectar un
dispositivo (dispositivo USB/ iPod/iPhone) al terminal de entrada USB.
ParaEn la placa frontal
Retroceder/avanzar
rápidamente
Seleccionar un archivo
Seleccionar una carpeta
Repetir reproducción
Reproducción aleatoria
y,
Pulse y mantenga pulsado
Pulse
S / T.
Pulse 2
J / 1 K.
Pulse 4
repetidamente.
Pulse 3
repetidamente.
S / T.
6
Page 29
Ajustes del menú
1 Pulse y mantenga pulsado para acceder a los ajustes del menú.
2 Gire la rueda de volumen para seleccionar un elemento y, a continuación,
pulse la rueda.
3 Repita el paso 2 hasta que se seleccione o active el elemento deseado.
4 Pulse para salir.
Para volver al elemento de ajuste anterior, pulse
• Para obtener más detalles sobre cada una de las opciones, consulte el MANUAL
DE INSTRUCCIONES en el siguiente sitio web: <http://www.jvc.net/cs/car/>
• La disponibilidad de cada opción varía según el modelo.
seleccionado. (Puede seleccionarse sólo si se selecciona
[ALLZONE]
6 Repita los pasos 4 y 5 para definir el color para las otras zonas.
7 Pulse para salir.
[COLOR49]
: Se muestra el color que ha creado para
o
[NIGHTCOLOR]
a
en el paso4.)
.
[COLORFLOW03]
: Se muestra el patrón del color
: El color cambia según
Otras informaciones
Con respecto a las operaciones de reproducción de las fuentes AUX, Spotify,
Pandora®, SiriusXM® Radio, AMAZON ALEXA , consulte el MANUAL DE
INSTRUCCIONES en el siguiente sitio web: <http://www.jvc.net/cs/car/>
• La disponibilidad de cada fuente varía según el modelo.
Nota sobre las especificaciones
Rango de frecuencia Bluetooth:
2,402 GHz—2,480 GHz
Potencia de salida de RF Bluetooth (E.I.R.P.):
+4 dBm (MAX), potencia clase 2
Impedancia del altavoz:
4Ω—8Ω
Voltaje de trabajo:
)
Batería de 12 V CC para vehículos
/
8
Page 31
Bluetooth®
• Las funciones Bluetooth podrían no funcionar con esta unidad, dependiendo
de la versión de Bluetooth, del sistema operativo y de la versión de firmware
de su teléfono móvil.
• Para realizar las siguientes operaciones, asegúrese de activar la función
Bluetooth del dispositivo.
• Las condiciones de la señal varían dependiendo del entorno.
Conecte el micrófono
Conecte el micrófono suministrado al terminal de entrada de micrófono o la toma
de entrada de micrófono en el panel trasero.
Ajuste el
ángulo del
micrófono
Emparejar y conectar por primera vez un dispositivo
Bluetooth
1 Pulse B SRC para encender la unidad.
2 Busque y seleccione el nombre de su receptor (“KD-X470BHS”/
“KD-X370BTS”/“KD-X37MBS”/“KD-X270BT”/“KD-SX26BT”) en el dispositivo
Bluetooth.
3 Realice (A) o (B) dependiendo de los datos mostrados en la pantalla.
En el caso de algunos dispositivos Bluetooth, la secuencia de emparejamiento
puede diferir de lo descrito en los siguientes pasos.
(A) “[Nombre del dispositivo]” “XXXXXX” “VOL–YES”
“BACK–NO”
“XXXXXX” es una clave de 6 dígitos que se genera aleatoriamente durante
cada emparejamiento.
Asegúrese de que las claves que aparecen en la unidad coincidan con las
que aparecen en el dispositivo Bluetooth.
Pulse la rueda de volumen para confirmar la clave.
Opere el dispositivo Bluetooth para confirmar la clave.
Asegúrelo mediante
abrazaderas para cable
(no suministradas) si
fuera necesario.
(B) “[Nombre del dispositivo]” “VOL–YES” “BACK–NO”
Pulse la rueda de volumen para iniciar el emparejamiento.
• Si “PAIRING” “PIN 0000” aparece en la pantalla, ingrese el código PIN
“0000” en el dispositivo Bluetooth.
• Si solo aparece “PAIRING”, opere el dispositivo Bluetooth para confirmar
el emparejamiento.
El mensaje “PAIRING COMPLETED” aparece cuando ha finalizado el
emparejamiento; “
” se iluminará cuando se establezca la conexión Bluetooth.
Contestar una llamada
Pulse o la rueda de volumen.
• Para ajustar el volumen del teléfono de
• Para finalizar una llamada, pulse y mantenga pulsado
volumen.
[00]
a
[35]
, gire la rueda de volumen.
o la rueda de
Reproductor de audio a través de Bluetooth
1 Pulse B SRC repetidamente para seleccionar BT AUDIO.
• Para KD-X270BT/KD-SX26BT: Si pulsa
BT AUDIO.
2 Para iniciar la reproducción, utilice el reproductor de audio a través de
Bluetooth.
ParaEn la placa frontal
Reproducción/pausaPulse la rueda de volumen.
Seleccione un grupo o carpeta
Omisión hacia atrás/omisión
hacia delante
Retroceder/avanzar rápidamente
Repetir reproducción
Reproducción aleatoria
se accede directamente a
J / 1 K.
Pulse 2
Pulse
S / T.
Pulse y mantenga pulsado
Pulse 4
repetidamente.
Pulse 3
repetidamente.
S / T.
9
Page 32
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• HD Radio Technology manufactured under license from iBiquity Digital Corporation. U.S. and Foreign Patents. For patents see http://dts.com/patents. HD Radio™ and the HD, HD Radio, and
“ARC” logos are registered trademarks or trademarks of iBiquity Digital Corporation in the United States and/or other countries.
• Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to
meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory
with an Apple product may affect wireless performance.
• Apple, iPhone, iPod, iPod touch, and Lightning are trademarks of Apple Inc., registered in the U.S. and other countries.
• SPOTIFY and the Spotify logo are among the registered trademarks of Spotify AB.
• Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved.
• Android is a trademark of Google LLC.
• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVCKENWOOD Corporation is under license. Other trademarks and
trade names are those of their respective owners.
• Amazon Alexa is not available in all languages and countries.
• Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates.