JVC KD-SV3105UH, KD-SV3105U, KD-SV3105UT, KD-SV3105UN, KD-SV3105 Instructions Manual
VCD/CD RECEIVER KD-SV3105
KD-SV3105
ATT
BAND
SOURCE
EQ
UP
REV FWD
VOL.
DOWN
VIDEO CD
PBCENTER
123
456
7809
RETURN
OSD
AUDIO
ENGLISH
For canceling the display demonstration, see page 9.
For installation and connections, refer to the separate manual.
INSTRUCTIONS
GET0262-001A
[U/UH]
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to
obtain the best possible performance from the unit.
ENGLISH
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave
all servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated.
Avoid direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
WARNING:
• DO NOT install any unit in locations
where;
– it may obstruct the steering wheel
and gearshift lever operations, as this
may result in a traffic accident.
– it may obstruct the operation of safety
devices such as air bags, as this may
result in a fatal accident.
– it may obstruct visibility.
• DO NOT operate any unit while
manipulating the steering wheel, as this
may result in a traffic accident.
• The driver must not watch the monitor
while driving.
If the driver watches the monitor while
driving, it may lead to carelessness and
cause an accident.
• If you need to operate the unit while
driving, be sure to look ahead carefully
or you may be involved in a traffic
accident.
• If the parking brake is not engaged,
“PARKING” flashes on the display, and
no playback picture will be shown on
the monitor.
– This warning appears only when
the parking brake wire is connected
to the parking brake system built
in the car (refer to the Installation/
Connection Manual).
How to reset your unit
This will reset the microcomputer. Your
preset adjustments will also be erased.
How to forcibly eject a disc
If a disc cannot be recognized by the unit or
cannot be ejected, ejects the disc as follows.
• If this does not work, reset your unit.
• Be careful not to drop the disc when it
ejects.
2
Contents
How to reset your unit ........................... 2
How to forcibly eject a disc ................... 2
How to read this manual ........................ 4
How to use the MODE button ............... 4
Control panel — KD-SV3105 ...... 5
Parts identification ................................. 5
Remote controller — RM-RK120
Main elements and features ................... 7
... 6
Getting started ....................... 8
Basic operations .................................. 8
Canceling the display demonstrations ... 9
Setting the clock .................................... 9
Radio operations ................... 10
Listening to the radio ........................... 10
Storing stations in memory .................... 11
Listening to a preset station ................... 12
Disc operations ...................... 13
Playing a disc in the unit ...................... 13
Playing a disc in the CD changer ........... 15
Playback Control (PBC) operations ...... 17
On-Screen (OSD) information ............... 18
Selecting the audio channel ................... 18
MP3/WMA control screen operations ... 18
Changing the display information ......... 19
Selecting the playback modes ................ 20
Sound adjustments ................ 21
Selecting preset sound modes
(C-EQ: custom equalizer) .................. 21
Adjusting the sound ............................... 22
ENGLISH
General settings — PSM ......... 23
Basic procedure ..................................... 23
Detaching the control panel .... 25
External component
operations ........................... 26
Playing an external component ............ 26
Maintenance .......................... 27
More about this unit ............... 28
Troubleshooting ..................... 30
Specifications ......................... 33
For safety....
• Do not raise the volume level too much, as
this will block outside sounds, making driving
dangerous.
• Stop the car before performing any
complicated operations.
Temperature inside the car....
If you have parked the car for a long time in
hot or cold weather, wait until the temperature
in the car becomes normal before operating the
unit.
3
How to read this manual
How to use the MODE button
The following methods are used to make the
explanations simple and easy-to-understand:
• Some related tips and notes are explained in
ENGLISH
“More about this unit” (see pages 28 and 29).
• Button operations are mainly explained with
the illustrations as follows:
Press briefly.
Press repeatedly.
Press either one.
If you press MODE, the unit goes into functions
mode, then the number buttons and
¢/4 buttons work as different
function buttons.
Ex.: When number button 2 works as
MO (monaural) button.
Press and hold until
your desired response
begins.
Press and hold both
buttons at the same
time.
The following marks are used to indicate...
: Built-in VCD/CD player
operations.
: External CD changer operations.
Time countdown indicator
To use these buttons for original functions
again after pressing MODE, wait for
5 seconds without pressing any of these buttons
until the functions mode is cleared.
• Pressing MODE again also clears the
functions mode.
4
Control panel — KD-SV3105
Parts identification
Display window
ENGLISH
1 +/– buttons
2 DISP (display) button
3 Remote sensor
4 Loading slot
5 Display window
6 MODE button
7 0 (eject) button
8
9
p SEL (select) button
q MO (monaural) button
w SSM (Strong-station Sequential Memory)
e SOURCE button
r • BAND button
• 6 (play/pause) button
t RPT (repeat) button
y RND (random) button
u EQ (equalizer) button
i
o Number buttons
¢/4 buttons
(standby/on/attenuator) button
button
(control panel release) button
Display window
; Tuner reception indicators—
MO (monaural), ST (stereo)
a Disc type indicators—WMA, MP3
s CH (CD changer) indicator
d CD indicator
f Playback mode / item indicators—
RND (random),
RPT (repeat)
g LOUD (loudness) indicator
h EQ (equalizer) indicator
j Sound mode (C-EQ: custom equalizer)
indicators—ROCK, CLASSIC, POPS,
HIP HOP, JAZZ, USER
•
k Disc information indicators—
TAG (ID3 Tag),
l Main display
/ Source display / Volume level indicator
z Tr (track) indicator
also works as the time countdown
indicator.
(disc), (folder),
(folder), (track/file)
5
Remote controller — RM-RK120
Installing the lithium coin battery
(CR2025)
ENGLISH
• Aim the remote controller directly at the
remote sensor on the unit. Make sure there is
no obstacle in between.
Caution:
• Do not leave the remote controller in a
place (such as dashboard) exposed to
direct sunlight for a long time.
Warning:
• Do not install any battery other than
CR2025 or its equivalent; otherwise, it
may explode.
• Store the battery in a place where children
cannot reach to avoid risk of accident.
• To prevent the battery from over-heating,
cracking, or starting a fire:
– Do not recharge, short, disassemble, or
heat the battery or dispose of it in a fire.
– Do not leave the battery with other
metallic materials.
– Do not poke the battery with tweezers or
similar tools.
– Wrap the battery with tape and insulate
when throwing away or saving it.
Remote sensor
• DO NOT expose the remote sensor to strong
light (direct sunlight or artificial lighting).
6
Main elements and features
ATT
VOL.
123
456
7809
1 SOURCE button
• Selects the playback source.
2
(standby/on attenuator) button
• Turns on and off the power and also
attenuates the sound.
3 2 REV / FWD 3 buttons
• Searches for stations if pressed briefly.
• Fast-forwards or reverses the track if
pressed and held.
• Changes the tracks/files of the disc.
4 VOL. + / – buttons
• Adjusts the volume level.
5 ENTER and number buttons
• Selects a track/file directly.
– Press the number button(s), then press
ENTER.
• Selects an item from the menu while
playing back a Video CD (VCD) in
Playback Control (PBC) function.
– Press the number button(s), then press
ENTER.
SOURCE
VIDEO CD
BAND
UP
REV FWD
DOWN
EQ
PBCENTER
RETURN
OSD
AUDIO
• Selects the discs while operating the CD
changer.
– To select disc number 1 – 6, press
number button 1 – 6 briefly.
– To select disc number 7 – 12, press and
hold number button 1 (7) – 6 (12).
6 EQ (equalizer) button
• Selects the sound mode (C-EQ: custom
equalizer).
7 BAND 6 button
• Changes the FM/AM bands.
• Stops disc playback temporarily. To
resume playback, press the button again.
– Not used for CD changer operations.
– While playing a VCD, the playback
scene at the moment stops and remain
stills.
8 5 UP / DOWN ∞ buttons
• Changes the preset stations.
• Changes the folder of the MP3/WMA
discs if pressed briefly.
• Changes the disc while operating the CD
changer if pressed and held.
9 PBC (Playback Control) button
• Activates or deactivates the PBC function.
p
RETURN button
• Returns to the previous menu while
playing a VCD in PBC function.
q OSD (On-Screen Display) button
• Turn on and off the OSD on the monitor.
w AUDIO button
• Selects the audio channel for VCD
playback.
ENGLISH
7
Getting started
ENGLISH
Basic operations
~
Ÿ
You cannot select some sources if they
are not ready.
! For FM/AM tuner
⁄ Adjust the volume.
Volume level appears.
@ Adjust the sound as you want.
(See pages 21 and 22.)
To drop the volume in a moment (ATT)
To restore the sound, press
it again.
To turn off the power
Caution on volume setting:
Discs produce very little noise compared
with other sources. Lower the volume
before playing a disc to avoid damaging
the speakers by the sudden increase of the
output level.
Volume level indicator
8
Canceling the display
Setting the clock
demonstrations
If no operations are done for about 20 seconds,
display demonstration starts.
[Initial: DEMO ON]—see page 24.
1
2
1
ENGLISH
2 Set the hour and minute.
1 Select “CLOCK H” (hour), then
adjust the hour.
2 Select “CLOCK M” (minute),
then adjust the minute.
3 Finish the procedure.
3
4
Finish the procedure.
To activate the display demonstration
In step 3 above...
To check the current clock time when the
power is turned off
9
Radio operations
ENGLISH
~
Listening to the radio
To tune in to a station manually
In step ! on the left...
1
Ÿ
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
Selected band appears.
! Start searching for a station.
When a station is received, searching
stops.
To stop searching, press the same
button again.
2 Select the desired station frequencies.
10
When an FM stereo broadcast is hard to
receive
Storing stations in memory
1
2
Lights up when monaural mode is activated.
Reception improves, but stereo effect will
be lost.
To restore the stereo effect, repeat the same
procedure. “MONO OFF” appears and the MO
indicator goes off.
You can preset six stations for each band.
FM station automatic presetting —
SSM (Strong-station Sequential
Memory)
1
2 Select the FM band (FM1 – FM3)
you want to store into.
3
ENGLISH
4
“SSM” flashes, then disappears when
automatic presetting is over.
Local FM stations with the strongest signals are
searched and stored automatically in the FM
band.
11
Manual presetting
Ex.: Storing FM station of 92.5 MHz into the
preset number 4 of the FM1 band.
ENGLISH
1
2
Listening to a preset station
1
2
3
4
Preset number flashes for a while.
3 Select the preset station (1 – 6) you
want.
To check the current clock time while
listening to an FM or AM station
12
Loading...