JVC KD-DV5306, KD-DV5305, KD-DV4306, KD-DV4305 Instructions Manual

For canceling the display demonstration, see page 5.
For installation and connections, refer to the separate manual.
KD-DV5306/KD-DV5305/ KD-DV4306/KD-DV4305
KD-DV5306/KD-DV5305
KD-DV4306/KD-DV4305
INSTRUCTIONS
GET0439-005A
[A]
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
How to forcibly eject a disc
[European Union only]
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
How to reset your unit
• Your preset adjustments will also be erased.
2
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
How to use functions mode
If you press M MODE, the unit goes into functions mode, then the number buttons and 5/ buttons work as different function buttons.
[Within 5 seconds...]
WARNINGS: To prevent accidents and damage
• DO NOT install any unit in locations where;
– it may obstruct the steering wheel and
gearshift lever operations.
– it may obstruct the operation of safety
devices such as air bags.
– it may obstruct visibility.
• DO NOT operate the unit while driving.
• If you need to operate the unit while
driving, be sure to look ahead carefully.
• The driver must not watch the monitor
while driving.
If the parking brake is not engaged,
“DRIVER MUST NOT WATCH THE MONITOR WHILE DRIVING.” appears on the monitor, and no playback picture will be shown. – This warning appears only when the
parking brake wire is connected to the parking brake system built in the car (refer to the Installation/Connection Manual).
CONTENTS
INTRODUCTIONS
Playable disc type .................................... 4
Preparation ............................................ 5
OPERATIONS
Basic operations
• Control panel ..................................... 6
• Remote controller (RM-RK241) ............ 7
Listening to the radio ............................... 10
Disc operations ........................................ 11
EXTERNAL DEVICES
Listening to the CD changer ...................... 19
Listening to the iPod / D. player ................. 20
Listening to the other external
components ......................................... 21
Caution on volume setting
Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.
For safety...
• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.
• Stop the car before performing any complicated operations.
Temperature inside the car...
If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.
SETTINGS
Selecting a preset sound mode .................. 22
General settings — PSM .......................... 23
Disc setup menu ....................................... 25
Assigning titles ........................................ 27
REFERENCES
Maintenance ........................................... 28
More about this unit ................................ 29
Troubleshooting ...................................... 34
Specifications .......................................... 36
The panel illustrations used in this manual are of KD-DV5306/KD-DV5305.
3
Playable disc type
Disc type Recording format, file type, etc Playable
DVD
DVD Recordable/Rewritable
2
/-RW, +R/+RW *3)
(DVD-R *
DVD-RAM
Dual Disc
CD/VCD
CD Recordable/Rewritable (CD-R/-RW)
• Compliant to ISO 9660 level 1,
level 2, Romeo, Joliet
*1 If you insert a DVD Video disc of an incorrect Region Code, “REGION CODE ERROR!” appears on the monitor. *2 DVD-R recorded in multi-border format is also playable (except for dual layer discs). *3 It is possible to play back finalized +R/+RW (Video format only) discs. However, the use of +R double layer disc on
this unit is not recommended.
*4 To reproduce DTS sound, use the DIGITAL OUT terminal (see also pages 26 and 31).
DVD-Video (Region Code numbers include “4”) *
DVD-Audio
DVD-ROM
DVD-Video
DivX Video
MPEG-1/MPEG-2 Video
MP3/WMA/WAV
JPEG/MPEG4
DVD-VR, +VR
All
DVD side
Non-DVD side
Audio CD (CD-DA)/DTS-CD *
VCD (Video CD)
CD-Text
CD-ROM
CD-I (CD-I Ready)
CD-DA
DivX Video, VCD (Video CD)
MPEG-1/MPEG-2 Video
MP3/WMA/WAV
JPEG/MPEG4
4
1
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.
4
Preparation
Cancel the display demonstration and set the clock
• See also page 24.
When the power is turned off: Check the current clock time When the power is turned on: Change the display information
~ Turn on the power. Ÿ Enter the PSM settings. ! ] ⁄ Cancel the display demonstrations
Select “DEMO,” then “DEMO OFF.”
Set the clock
Select “CLOCK H” (hour), then adjust the hour. Select “CLOCK M” (minute), then adjust the minute.
@ Finish the procedure.
Detaching the control panel
Attaching the control panel
5INTRODUCTIONS
Basic operations — Control panel
FM/AM: Select preset station.
DISC: Select title/folder.
IPOD/D.PLAYER: Enter the main menu/
Pause or stop playback/Confirm selection.
Change the display information.
Select the sound mode.
Volume control [Turn]
Eject disc.
Adjust the sound mode.
Enter the PSM settings [Hold].
FM/AM: Search for station.
DISC: Select chapter/track.
IPOD/D.PLAYER: Select track.
Turn on the power.
Turn off the power [Hold].
Attenuate the sound (if the power is on).
Display window
Loading slot
Connect an external component *
FM/AM: Select preset station.
DISC: Select chapter/title/folder/
track/disc (for CD changer).
1
.
Detach the panel.
Enter functions mode.
Press M MODE, then one of the following buttons
FM/AM: Select the bands.
DISC: Start playback.
Select the source. FM/AM D.PLAYER *2 (or EXT IN) = LINE IN *1 = AUX IN *1 = (back to the beginning)
*1 Only for KD-DV5306/KD-DV5305. *2 You cannot select these sources if they are not ready or not connected.
= DISC *
2
= CD-CH *2/IPOD *2/
(within 5 seconds)...
MO : Turn on/off monaural reception. SSM : Automatic station presetting [Hold]. RPT : Select repeat play. RND : Select random play.
5/ : Skip 10 chapters/tracks.
6
Display window
Track information indicators
Playback mode/item indicators (Random/Repeat)
Loudness indicator
Playback source indicators
Source display/Preset No./Track No./ Folder No./Disc No./Chapter No.
Track indicator
Tuner reception indicators
Main display
(Time, menu, playback information)
Basic operations — Remote controller (RM-RK241)
Installing the lithium coin battery (CR2025)
Before using the remote controller:
• Aim the remote controller directly at the remote sensor on the unit.
• DO NOT expose the remote sensor to bright light (direct sunlight or artificial lighting).
Equalizer indicator
Sound mode indicators
Remote sensor
Continued on the next page
7OPERATIONS
Warning: To prevent accidents and damage
• Do not install any battery other than CR2025 or its equivalent.
• Do not leave the remote controller in a place (such as dashboards) exposed to direct sunlight for a long time; otherwise, it may explode.
• Store the battery in a place where children cannot reach.
• Do not recharge, short, disassemble, heat the battery, or dispose of it in a fire.
• Do not leave the battery with other metallic materials.
• Do not poke the battery with tweezers or similar tools.
• Wrap the battery with tape and insulate when throwing away or saving it.
EXTRA MONITOR
1 Monitor control buttons
• Used for a JVC monitor—KV-MR9010, KV-MH6510, KV-M706, or KV-M705.
DVD/RECEIVER
2 • Turns the power on if pressed briefly or
attenuates the sound when the power is on.
• Turns the power off if pressed and held.
3 Selects the source. 4 Selects the FM/AM bands. 5 Not applicable for this unit. 6 Not applicable for this unit. 7 Adjusts the volume level.
• 2nd VOL: Not applicable for this unit.
1
8 *
• DVD-Video/DivX: Shows disc menu.
• VCD: Starts PBC playback.
1
9 *
Enters disc setup menu.
p SHIFT button q 7 (stop), 3 (play), 8 (pause)
3 (play) also function as ZOOM button when pressed with SHIFT button (see page 15).
• Not applicable for CD changer/iPod/D. player operations.
w For advanced disc operations:
5 / ∞ :
DVD-Video: Selects the titles. DivX/MPEG Video/MP3/WMA/WAV: Selects
the folders if included.
4 / ¢ :
– Reverse skip/forward skip if pressed briefly. – Reverse search/forward search if pressed
and held.
1 / ¡ : Reverse search/forward
search. *
2
For FM/AM tuner operations:
5 / ∞ : Changes the preset stations.
4 / ¢ :
– Searches for stations automatically if
pressed briefly.
– Searches for stations manually if pressed
and held.
8
For Apple iPod/JVC D. player operations:
∞ : Pauses/stops or resumes playback. 5 : Enters the main menu. (Now 5//4 / ¢ work as the
menu selecting buttons.) *
3
4 / ¢ (in menu selecting mode): – Selects an item if pressed briefly. (Then,
to confirm the selection.)
press
– Skips 10 items at a time if pressed and held.
4 / ¢ : – Reverse skip/forward skip if pressed briefly. – Reverse search/forward search if pressed
and held.
e Shows the on-screen bar.
• Also functions as DIRECT button when pressed with SHIFT button. *
1
r *
• DVD-Video/DivX: Shows disc menu.
4
• VCD: Starts PBC playback.
1
t *
• Makes selection/settings.
@ / # : DivX: Searches for index during play.
• DISC +/–: Changes discs when the source is “CD-CH.”
1
y *
RETURN button
u • DVD-Video: Selects audio language ( ),
subtitles ( )*1, angle ( )*5.
• DivX: Selects audio language (
),
subtitles ( ).
• VCD: Selects audio channel ( ).
How to select a number
An input screen appears...
How to select a preset station
1
*
Functions as number buttons when pressed with
SHIFT button.
– FM/AM: Selects preset stations. – DISC: Selects chapter/title/folder/track after
entering search mode by pressing SHIFT and DIRECT.
2
Not applicable for CD changer operations.
* *3 5 : Returns to the previous menu. : Confirms the selection. *4 You can directly select title/chapter/folder/track using
the number buttons (see pages 13 – 15).
*5 Functions as SURROUND button when pressed with
SHIFT button (not applicable for this unit).
9OPERATIONS
Listening to the radio
Change the display information
~ Select “FM/AM.”
* If no name is assigned to a station, “NO NAME”
appears. To assign a name to a station, see page 27.
Select preset station.
Lights up when receiving an FM stereo broadcast with sufficient signal strength.
Ÿ Select the bands.
! Search for a station to listen—Auto Search.
Manual Search: Hold either one of the buttons until “M” flashes on the display, then press it repeatedly.
When an FM stereo broadcast is
3
hard to receive
1
Local FM stations with the strongest signals are
searched and stored automatically in the FM band.
2
Manual presetting
Reception improves, but stereo effect will be lost.
• MO indicator lights up.
FM station automatic presetting — SSM (Strong-station Sequential
Ex.: Storing FM station of 92.5 MHz into preset number
4 of the FM1 band.
1
2
Memory)
You can preset six stations for each band.
1
3
2
10
Disc operations
Before performing any operations...
Turn on the monitor to watch the playback picture. If you turn on the monitor, you can also control playback of other discs by referring to the monitor screen. (See pages 15 – 18.) The disc type is automatically detected, and playback starts automatically (for DVD: automatic start depends on its internal program). If the current disc does not have any disc menu, all tracks will be played repeatedly until you change the source or eject the disc.
” appears on the monitor when pressing a button, the unit cannot accept the operation you have tried to
If “ do.
• In some cases, without showing “ ,” operations will not be accepted.
Insert the disc.
Playback starts automatically.
Start playback if necessary.
Change the display information
Prohibiting disc ejection
To cancel the prohibition, repeat the same procedure.
1
If the file does not have Tag information or
*
“TAG DISP” is set to “TAG OFF” (see page
24), folder name and file name appear. TAG indicator will not light up.
2
*
“NO NAME” appears for an audio CD.
11OPERATIONS
Operations using the control panel
Pressing (or holding) the following buttons allows you to...
Disc type
Press: Select chapter Hold: Reverse/fast-forward
1
chapter *
Press: Select track Hold: Reverse/fast-forward track *
Press: Select track Hold: Reverse/fast-forward track *
Press: Select track Hold: Reverse/fast-forward track *
Press: Select track Hold: Reverse/fast-forward track *
1
Search speed changes to on the monitor.
* *2 Search speed changes on the monitor. *3 Press to select number 1 to 6; hold to select number 7 to 12.
After pressing , press the following buttons to...
Select title During stop: Locate title
Select folder Locate particular folder directly
2
1
Select folder Locate particular folder directly
1
1
Disc type
Skip 10 chapters (during play or pause)
Skip 10 tracks (within the same folder)
Skip 10 tracks (PBC not in use)
Skip 10 tracks (within the same folder)
Skip 10 tracks TRK RPT: Repeat current track DISC RND: Randomly play all
• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”
CHP RPT: Repeat current
chapter
TIT RPT: Repeat current title
TRK RPT: Repeat current track FLDR RPT: Repeat current folder
TRK RPT: Repeat current track
(PBC not in use)
TRK RPT: Repeat current track FLDR RPT: Repeat current folder
(Number buttons) *
3
During play/pause: Locate chapter
Locate particular track directly (PBC not in use)
Locate particular track directly
DISC RND: Randomly play all
tracks (PBC not in use)
FLDR RND: Randomly play all
tracks of current folder, then tracks of next folders
DISC RND: Randomly play all
tracks
tracks
12
Loading...
+ 26 hidden pages