JVC KD-DV4207 User manual
ENGLISHРУCCKИЙ
DVD/CD RECEIVER
ПРИЕМНИК ДЛЯ ВОСПРОИЗВЕДЕНИЯ ДИСКОВ DVD И КОМПАКТ-ДИСКОВ
KD-DV4207
For installation and connections, refer to the separate manual.
Указания по установке и выполнению соединений приводятся в отдельной инструкции.
INSTRUCTIONS
ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ
GET0373-001A
[EE]
For canceling the display demonstration, see page 5.
Информацию об отмене демонстрации функций дисплея см. на стр. 5.
В соответствии с Законом Российской Федерации “О защите прав потре бителей” срок службы
(годности) данного товара “по истечении которого он может представлять опасность для жизни,
здоровья потребителя, причинять вред его имуществу или окружающей среде” составляет семь (7)
лет со дня производства. Этот срок является временем, в течение которого потребитель данного
товара может безопасно им пользоваться при условии соблюдения ин струк ции по эксплуатации
данного товара, проводя необходимое обслуживание, включающее замену расходных материалов
и/или соответствующее ремонтное обеспечение в специализированном сервисном центре.
Дополнительные косметические материалы к данному товару, поставляе мые вместе с ним, могут
храниться в течение двух (2) лет со дня его производства.
Срок службы (годности), кроме срока хранения дополнительных космети ческих материалов,
упомянутых в предыдущих двух пунктах, не затрагивает никаких других прав потребителя, в
частности, гарантийного свидетельства JVC, которое он может получить в соответствии с законом о
правах потребителя или других законов, связанных с ним.
ENGLISH
2
This product incorporates copyright
protection technology that is protected
by U.S. patents and other intellectual
property rights. Use of this copyright
protection technology must be authorized
by Macrovision, and is intended for home
and other limited viewing uses only unless
otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
How to reset your unit
• Your preset adjustments will also be erased.
How to forcibly eject a disc
• If this does not work, reset your unit.
• Be careful not to drop the disc when it
ejects.
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to
obtain the best possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave
all servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated.
Avoid direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
How to use functions mode
If you press MODE, the unit goes into
functions mode, then the number buttons
and 5/∞ buttons work as different function
buttons.
How to detach/attach the control panel
Detaching...
Attaching...
[Within 5 seconds...]
ENGLISH
3
WARNINGS:
To prevent accidents and damage
• DO NOT install any unit in locations where;
– it may obstruct the steering wheel and
gearshift lever operations.
– it may obstruct the operation of safety devices
such as air bags.
– it may obstruct visibility.
• DO NOT operate the unit while driving.
• If you need to operate the unit while driving, be
sure to look ahead carefully.
• The driver must not watch the monitor while
driving.
If the parking brake is not engaged, “DRIVER
MUST NOT WATCH THE MONITOR WHILE DRIVING.”
appears on the monitor, and no playback picture
will be shown.
– This warning appears only when the parking
brake wire is connected to the parking brake
system built in the car (refer to the Installation/
Connection Manual).
For safety...
• Do not raise the volume level too much, as
this will block outside sounds, making driving
dangerous.
• Stop the car before performing any
complicated operations.
Temperature inside the car...
If you have parked the car for a long time in hot
or cold weather, wait until the temperature in
the car becomes normal before operating the
unit.
CONTENTS
Introduction ............................................. 4
OPERATIONS
Basic operations
• Control panel .......................................... 6
• Remote controller (RM-RK230) ................ 7
Listening to the radio ................................ 9
Searching for FM RDS programme
— PTY search ....................................... 10
Disc operations ......................................... 12
EXTERNAL DEVICES
Listening to the CD changer ....................... 18
Listening to the DAB tuner ......................... 19
Listening to the iPod®/D. player ................. 20
Listening to the other external
components .......................................... 21
SETTINGS
Selecting a preset sound mode — C-EQ ...... 22
General settings — PSM ........................... 23
DVD setup menu ....................................... 25
Maintenance ............................................ 28
More about this unit ................................. 29
Troubleshooting ....................................... 31
Specifications ........................................... 34
ENGLISH
4
Disc type Playable Unplayable
DVD Video, Dual Disc (DVD side only),
DVD-R*/-RW, +R/+RW
• Recorded in DVD-Video format only and in
PAL color system
DVD Audio, Dual Disc (non-DVD side),
DVD-RAM, DVD-ROM, DVD-R/-RW, +R/+RW
• Recorded in DVD-VR format
Video CD
CD-R/-RW
SVCD (Super Video CD)
DVD-R/-RW, +R/+RW, DVD-ROM
• Compliant to UDF bridge format
—
CD-R/-RW
• Compliant to ISO 9660 level 1, ISO 9660
level 2, Romeo, Joliet
—
Audio CD, CD Text
CD-R/-RW
• Compliant to CD-DA format
CD-ROM, CD-I (CD-I Ready), Photo CD
• It is possible to play back finalized +R/+RW (Video mode only) discs. However, the use of +R double layer disc on this unit is not
recommended.
* DVD-R recorded in multi-border format is also playable (except for dual layer discs).
Introduction
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not
comply with the “Compact Disc Digital Audio”
standard. Therefore, the use of Non-DVD
side of a DualDisc on this product may not be
recommended.
Caution on volume setting
Discs produce very little noise compared with
other sources. Lower the volume before playing
a disc to avoid damaging the speakers by the
sudden increase of the output level.
Note on Region Code:
DVD players and DVD Video discs have
their own Region Code numbers. This unit
can only play back DVD discs whose Region
Code numbers include “5.”
Examples:
If you insert a DVD Video disc of an
incorrect Region Code
“REGION CODE ERROR!” appears on the
monitor.
ENGLISH
5
Before operating the unit — Cancel the display demonstration and set the clock
• See also page 23.
~ Turn on the power.
Ÿ Enter the PSM settings.
! ] ⁄ Cancel the display demonstrations
Select “DEMO,” then “DEMO OFF.”
Set the clock
Select “CLOCK H” (hour), then adjust the hour.
Select “CLOCK M” (minute), then adjust the minute.
Select “24H/12H,” then “24H” (hour) or “12H” (hour).
@ Finish the procedure.
When the power is turned off:
Check the current clock time
When the power is turned on:
Change the display information
6
ENGLISH
Basic operations — Control panel
• FM/AM/DAB: Select the bands.
• DISC: Start playback.
Select the source.
FM/AM = DAB* = DISC* = CD-CH*/IPOD*/
D.PLAYER* (or EXT IN) = (back to the beginning)
* You cannot select these sources if they are not ready.
Change the display information.
Display window
• DISC: Select folder.
Also functions as +10/–10 buttons after pressing MODE
to skip 10 chapters/tracks at a time.
• IPOD/D.PLAYER: Enter the main menu/Pause
or stop playback/Confirm selection.
• DAB: Select service.
Activate/deactivate TA
Standby Reception.
Hold to enter RDS programme search.
Eject disc.
Detach the panel.
Adjust the sound mode.
Hold to enter the PSM settings.
Enter functions mode.
Press MODE, then one of the following buttons (within
5 seconds)...
EQ: Select the sound mode.
MO: Turn on/off monaural reception.
SSM: Automatic station presetting.
RPT: Select repeat play.
RND: Select random play.
• FM/AM/DAB: Select preset station/service.
• DISC: Select chapter/title/folder/track/disc
(for CD changer).
• FM/AM/DAB: Search for station/
service.
• DISC: Select chapter/track.
• IPOD/D.PLAYER: Select track.
• Turn on the power.
• Turn off the power [Hold].
• Attenuate the sound (if the power is on).
Insert disc.Volume control
7
ENGLISH
OPERATIONS
Display window
Basic operations — Remote controller (RM-RK230)
Installing the lithium coin battery (CR2025)
Before using the remote controller:
• Aim the remote controller directly at the
remote sensor on the unit.
• DO NOT expose the remote sensor to bright
light (direct sunlight or artificial lighting).
Remote sensor
Continued on the next page
Track information indicators
Tuner reception indicators
Main display
(Time, menu, playback information)
Source display/Preset No./Track No./
Folder No./Disc No./Chapter No./
Channel No.
Loudness indicatorDisc type indicators
Playback source indicators Equalizer indicator
Sound mode indicators
Playback mode/item indicators
(Random/Repeat)
Warning:
To prevent accidents and damage
• Do not install any battery other than
CR2025 or its equivalent.
• Store the battery in a place where children
cannot reach.
• Do not recharge, short, disassemble, heat
the battery, or dispose of it in a fire.
• Do not leave the battery with other
metallic materials.
• Do not poke the battery with tweezers or
similar tools.
• Wrap the battery with tape and insulate
when throwing away or saving it.
Track indicator
RDS indicators
8
ENGLISH
For FM/AM tuner operations:
• PRESET 5 / ∞
Changes the preset stations.
• 4 / ¢
– Searches for the stations if pressed
briefly.
– Manual searches if pressed and held.
For DAB tuner operations:
• PRESET 5 / ∞
Changes the preset services.
• 4 / ¢
– Changes the services if pressed briefly.
– Searches the ensembles if pressed and
held.
For iPod/D. player operations:
• 5 / ∞
∞: Pauses/stops or resumes playback.
5: Enters the main menu.
(Now 5/∞/4 / ¢ work as the
menu selecting buttons.)*
3
• 4 / ¢ (in menu selecting mode)
– Selects an item if pressed briefly.
(Then, press ∞ to confirm the
selection.)
– Skips 10 items at a time if pressed and
held.
w • Shows the on-screen bar.
• Also function as the
/TITLE button
when pressed with SHIFT button (see
pages 14 and 15).
e*
1
• DVD: Shows the DVD disc menu.
• VCD: Starts PBC playback.
r*
1
• Makes selection/settings.
• DISC +/– buttons: Changes discs when
the source is “CD-CH.”
t*
1
RETURN button
y • DVD: Selects audio language (
),
subtitles ( ), angle ( ).
• VCD: Selects audio channel ( ).
*
1
Functions as number buttons when pressed
with SHIFT button.
–
FM/AM/DAB: Selects preset stations/
services.
–
DISC: Selects chapter/title/folder/track.
*
2
Functions as +10/–10/+100/–100 buttons
when pressed with SHIFT button.
*
3
5 : Returns to the previous menu.
∞ : Confirms the selection.
MONITOR CONTROL
1 Monitor control buttons
• Used for a JVC monitor—KV-MR9010
or KV-MH6510.
DVD/RECEIVER CONTROL
2 Turns on/off the power.
• Attenuates the sound if the power is on.
3 Selects the source.
4 Selects the FM/AM/DAB bands.
5*
1
• DVD: Shows the DVD disc menu.
• VCD: Starts PBC playback.
6 Not applicable for this unit.
7 Adjusts the volume level.
• 2nd VOL:
Not applicable for this unit.
8*1 Enters DVD setup menu.
9 SHIFT button
p 7 (stop), 3 (play), 8 (pause)
• 3 (play) also function as ZOOM button
when pressed with SHIFT button (see
page 14).
•
Not applicable for CD changer/iPod/
D. player operations.
q*2 For advanced disc operations:
• /TITLE 5 / ∞
DVD: Selects the titles.
MP3/WMA: Selects the folders if included.
• 4 / ¢: Reverse skip/forward skip.
• 1 / ¡: Reverse search/forward
search (not applicable for CD changer
operations).
9
ENGLISH
OPERATIONS
When an FM stereo broadcast is hard to
receive
1
2
Reception improves, but stereo effect will be
lost.
• MO indicator lights up.
FM station automatic presetting —SSM
(Strong-station Sequential Memory)
You can preset six stations for each band.
1
2
Listening to the radio
Change the display information
(non-RDS station)
~ Select “FM/AM.”
Ÿ Select the bands.
! Search for a station to listen—Auto
Search.
• Manual Search: Hold either one of the
buttons until “M” flashes on the display,
then press it repeatedly.
Select preset station.
3
Local FM stations with the strongest signals
are searched and stored automatically in the
FM band.
Manual presetting
Ex.: Storing FM station of 92.5 MHz into preset
number 4 of the FM1 band.
1
2
3
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
Note:
FM1 and FM2: 87.5 MHz – 108.0 MHz
FM3: 65.00 MHz – 74.00 MHz
10
ENGLISH
Searching for FM RDS programme — PTY search
Change the display information
~ Activate PTY Search.
Ÿ Select one of the PTY codes (programme
types).
See the following for details.
! Start searching.
If there is a station broadcasting a
programme of the same PTY code as you
have selected, that station is tuned in.
Preset PTY codes in the number buttons
(1 to 6):
PTY codes (available with the control dial):
NEWS, AFFAIRS, INFO, SPORT, EDUCATE, DRAMA, CULTURE,
SCIENCE, VARIED, POP M (music), ROCK M (music), EASY
M (music), LIGHT M (music), CLASSICS, OTHER M (music),
WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE
IN, TRAVEL, LEISURE, JAZZ, COUNTRY, NATION M (music),
OLDIES, FOLK M (music), DOCUMENT
Storing your favorite programme types
You can store your favorite PTY codes into the
number buttons.
1 Select a PTY code (see left column).
2 Select a preset number.
3 Repeat steps 1 and 2 for storing other
PTY codes.
4
11
ENGLISH
OPERATIONS
Activating/deactivating TA/PTY Standby Reception
TA Standby Reception Indicator PTY Standby Reception Indicator
Press
to activate.
See page 23.
The unit temporarily will switch
to Traffic Announcement (TA), if
available, from any source other than
AM.
The volume changes to the preset
TA volume level if the current level
is lower than the preset level (see
page 23).
Lights up The unit temporarily will switch to
your favorite PTY programme from
any source other than AM.
Lights up
Not yet activated. Tune in to another
station providing the RDS signals.
Flashes Not yet activated. Tune in to
another station providing the RDS
signals.
Flashes
Press
to deactivate.
Goes off Select “OFF” for the PTY code (see
page 23).
Goes off
When driving in an area where FM reception
is not sufficient enough, this unit automatically
tunes in to another FM RDS station of the
same network, possibly broadcasting the same
programme with stronger signals (see the
illustration on the right).
When shipped from the factory, NetworkTracking Reception is activated.
To change the Network-Tracking Reception
setting, see “AF-REG” on page 23.
• When the DAB tuner is connected, refer to
“Tracing the same programme—Alternative
Frequency Reception” on page 19.
Tracing the same programme—Network-Tracking Reception
Programme A broadcasting on different frequency areas
(01 – 05)
Automatic station selection—Programme Search
Usually when you press the number buttons, the preset station is tuned in.
If the signals from the RDS preset station are not sufficient for good reception, this unit, using the
AF data, tunes in to another frequency broadcasting the same programme as the original preset
station is broadcasting.
• The unit takes some time to tune in to another station using programme search.
• See also page 24.
12
ENGLISH
Disc operations
Before performing any operations...
Turn on the monitor for playing a DVD or VCD. If you turn on the monitor, you can also control
playback of other discs by referring to the monitor screen. (See pages 15 – 17.)
The disc type is automatically detected, and playback starts automatically (for DVD: automatic start
depends on its internal program).
If the current disc does not have any disc menu (when playback stops), all tracks will be played
repeatedly until you change the source or eject the disc.
If “
” appears on the monitor when pressing a button, the unit cannot accept the operation you
have tried to do.
• In some cases, without showing “ ,” operations will not be accepted.
Insert disc.
Playback starts automatically with most of the discs.
Eject disc.
Change the display information
Start playback if necessary.
Prohibiting disc ejection
To cancel the prohibition, repeat
the same procedure.
*1 If the file does not have Tag information or “TAG
DISP” is set to “TAG OFF” (see page 24), folder
name and file name appear. TAG indicator will
not light up.
*
2
“NO NAME” appears for an audio CD.
ENGLISH
OPERATIONS
13
Operations using the control panel
Pressing (or holding) the following buttons allows you to...
Disc type
(Number buttons)
Press: Select chapter
Hold: Reverse /fast-forward
chapter*
—
During stop: Locate title
During play/pause: Locate
chapter
Press: Select track
Hold: Reverse /fast-forward
track*
—
Locate particular track directly
(PBC not in use)
Select track Select folder Locate particular folder directly
Press: Select track
Hold: Reverse /fast-forward
track*
—
Locate particular track directly
* Search speed changes to
on the monitor.
After pressing , press the following buttons to...
Disc type
Skip 10 chapters (during play
or pause)
CHP RPT:
Repeat current chapter
TIT RPT:
Repeat current title
—
Skip 10 tracks (PBC not in use) TRK RPT:
Repeat current track (PBC not
in use)
DISC RND:
Randomly play all tracks (PBC
not in use)
Skip 10 tracks (within the same
folder)
TRK RPT:
Repeat current track
FLDR RPT:
Repeat current folder
FLDR RND:
Randomly play all tracks of
current folder, then tracks of
next folders
DISC RND:
Randomly play all tracks
Skip 10 tracks TRK RPT:
Repeat current track
DISC RND:
Randomly play all tracks
• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”
14
ENGLISH
Canceling the PBC playback...
1
2 While holding , press *3 to start the
desired track.
• To resume PBC, press / .
To enlarge the view (Zoom in)...
1 While holding , press
ZOOM
repeatedly.
2 Move the enlarged portion.
• To cancel zoom, select “ZOOM OFF.”
Operations using the remote controller—RM-RK230
: Stop play
: Pause (Frame by frame playback if pressed during pause.)
: Start play (10-second review if pressed during play.)
: Reverse/forward chapter search*1
• Slow motion during pause. No sound can be heard.*
2
: Press: Select chapter (during play or pause)
Hold: Reverse/fast-forward chapter search
: Select title
: Select audio language
: Select subtitle language
: Select view angle
: Stop play
: Pause (Frame by frame playback if pressed during
pause.)
: Start play
: Reverse/forward track search*1
• Slow motion during pause. No sound can
be heard.*
2
• Reverse slow motion does not work.
: Press: Select track
Hold: Reverse/fast-forward track search
: Select audio channel (ST: stereo, L: left, R: Right)
While holding ...*
3
: Select track (For VCD with PBC, a list of items is
shown on the disc menu.)
• To return to the previous menus, press .
To enlarge the view (Zoom in)...
1 While holding , press
ZOOM
repeatedly.
2 Move the enlarged portion.
• To cancel zoom, select “ZOOM OFF.”
Using menu driven features...
1 /
2 Select an item you want to start play.
3
While holding ...*
3
: Select chapter (during play or
pause)
Select title (when stop)
, then :
Select title directly
ENGLISH
OPERATIONS
15
Ex.: Time search
• DVD: _:_ _:_ _
To enter 1 (hours): 02 (minutes): 00
(seconds), press 1, 0, 2, 0, then 0.
• VCD (PBC not in use): _ _:_ _
To enter 64 (minutes): 00 (seconds),
press 6, 4, 0, then 0.
: Stop play
: Pause
: Start play (Playback starts from the beginning of
the track.)
: Select tracks
: Select folder
While holding ...*
3
: Select track (within the same folder)
, then : Select folder directly*
4
: Stop play
: Pause
: Start play
: Reverse/forward track search
: Press: Select tracks
Hold: Reverse/fast-forward track search
While holding ...*
3
: Select track directly
Operations using the on-screen bar
These operations are possible on the monitor using the remote controller.
~ Show the on-screen bar (see page 16).
(once) for MP3/WMA/CD
(twice) for DVD/VCD
Ÿ Select an item.
! Make a selection.
If pop-up menu appears...
• For entering time/numbers, see the following.
⁄ Remove the on-screen bar.
Continued on the next page
Entering time/numbers
• To select numbers 0 – 9:
While holding , press .
• To select numbers greater than 9:
While holding , press . Then, press
.
• After entering the numbers, press .
• To reduce numbers, use .
• To correct a misentry, use .
*1 Search speed changes to on the monitor if pressed repeatedly.
*2 Slow motion speed changes to on the monitor if pressed repeatedly.
*3 For selecting numbers greater than 9 or 99, press or , then follow by .
*4 To use direct folder access on MP3/WMA discs, it is required that folders are assigned with 2-digit numbers at the beginning of their
folder names—01, 02, 03, and so on.
16
ENGLISH
Information
Operation
On-screen bar
1 Disc type
2 DVD/DTS audio CD: Audio signal format type
VCD: PBC
3 Playback information
Current title/chapter
Current track
4 Time indication
Elapsed playing time of the disc (For DVD,
elapsed playing time of the current title.)
DVD: Remaining title time
VCD: Remaining disc time
Elapsed playing time of the current
chapter/track
Remaining time of the current chapter/
track
5 Playback status
Play
Forward/reverse search
Forward/reverse slow-motion
Pause
Stop
6 Operation icons
Change the time indication (see 4)
Time Search (Enter the elapsed playing
time of the current title or of the disc.)
Title Search (by its number)
Chapter Search (by its number)
Track Search (by its number)
Change the audio language or audio
channel
Change the subtitle language
Change the view angle
DVD: Repeat play
VCD/MP3/WMA/CD: Repeat play
Intro play
Random play
Repeat play*1 :
(PBC not in use)
Repeat play*
1
:
Random play*1 :
Intro play*2 :
Repeat play*1 :
Random play*1 :
Intro play*2 :
Repeat play*1 :
Random play*1 :
Intro play*2 :
*1 For repeat play/random play, see also page 13.
*2 Plays the beginning 15 seconds of...
INTRO TRACK (INTRO): All tracks of the current disc.
INTRO FOLDER: First tracks of all folders of the current
disc.
ENGLISH
OPERATIONS
17
Folder/track list screen
Before playing, you can display the folder
list/track list to confirm the contents and start
playing a track.
~ Display the folder/track list while stop.
Ÿ Select an item from the list.
• MP3/WMA: Track list of the selected
folder appears.
• To go back to the previous screen, press
.
1 Current folder number/total folder number
2 Current track number/total number of
tracks in the current folder or in disc (CD)
3 Current page/total number of the pages
included in the list
4 Current folder/track (highlighted bar)
Control screen
The control screen automatically appears when
you insert a disc.
~ Select “Folder” column or ”Track” column
on the control screen.
Ÿ Select a folder or track to start playing.
1 Current folder number/total folder number
2 Folder list with the current folder selected
3 Selected playback mode
4 Elapsed playing time of the current track
5 Operation mode icon ( ‰, 7, 8, ¡, 1 )
6 Current track number/total number of
tracks in the current folder (total number of
tracks on the disc)
7 Track information
8 Track list with the current track selected
Operations using the control/list screen (MP3/WMA/CD)
These operations are possible on the monitor using the remote controller.
• Folder selection/information is only for MP3/WMA discs.
Ex.: MP3/WMA disc
Ex.: Folder list
18
ENGLISH
Listening to the CD changer
Change the display information
(see page 12)
Press: Select track
Hold: Reverse/fast-forward track
MP3: Select folders
After pressing
, press the following
buttons to...
Skip 10 tracks (MP3: within the same
folder)
TRK RPT: Repeat current track
FLDR RPT: MP3: Repeat all tracks of
current folder
DISC RPT: Repeat all tracks of the
current disc
FLDR RND: MP3: Randomly play
all tracks of the current
folder, then tracks of the
next folder
DISC RND: Randomly play all tracks of
current disc
MAG RND: Randomly play all tracks of
the inserted discs
• To cancel repeat play or random play, select
“RPT OFF” or “RND OFF.”
It is recommended to use a JVC MP3-compatible CD changer with your unit.
• You can only play conventional CD (including CD Text) and MP3 discs.
~ Select “CD-CH.”
Ÿ Select a disc to start playing.
Press: For selecting disc number 1 – 6.
Hold: For selecting disc number 7 – 12.
19
ENGLISH
EXTERNAL DEVICES
Listening to the DAB tuner
Change the display informationSelect preset service.
~ Select “DAB.”
Ÿ Select the bands.
! Searching for an ensemble.
• Manual Search: Hold either one of the buttons until “M” flashes on the display, then press it
repeatedly.
⁄ Select a service (either primary or secondary) to listen to.
Storing DAB services in memory
While listening to a DAB service...
Activating/deactivating TA/PTY Standby
Reception
• Operations are exactly the same as explained
on page 11 for FM RDS stations.
• You cannot store PTY codes separately for the
DAB tuner and for the FM tuner.
Tracing the same programme—Alternative
Frequency Reception
• While receiving a DAB service:
When driving in an area where a service
cannot be received, this unit automatically
tunes in to another ensemble or FM RDS
station, broadcasting the same programme.
• While receiving an FM RDS station:
When driving in an area where a DAB service
is broadcasting the same programme as the
FM RDS station is broadcasting, this unit
automatically tunes in to the DAB service.
When shipped from the factory, Alternative
Frequency Reception is activated.
To deactivate the Alternative Frequency
Reception, see page 24.
20
ENGLISH
Listening to the iPod®/D. player
Change the display information
Before operating, connect the interface adapter
(KS-PD100 or KS-PD500) to the CD changer
jack of this unit.
Preparations:
Make sure “CHANGER” is selected for the
external input setting, see page 24.
~ Select “IPOD” or “D. PLAYER.”
Ÿ Select a song to start playing.
Selecting a track from the menu
1 Enter the main menu.
• This mode will be canceled
if no operations are done for
about 5 seconds.
2 Select the desired menu.
For iPod:
PLAYLIST Ô ARTISTS Ô ALBUMS Ô SONGS
Ô GENRES Ô COMPOSER Ô (back to the
beginning)
For D. player:
PLAYLIST Ô ARTIST Ô ALBUM Ô
GENRE Ô TRACK Ô (back to the beginning)
3 Confirm the selection.
• To move back to the previous
menu, press 5.
• If a track is selected, playback starts
automatically.
• Holding
4/¢ can skip 10
items at a time.
Pause/stop playback
• To resume playback, press it again.
Press: Select tracks
Hold: Reverse/fast-forward track
After pressing
, press the following
buttons to...
ONE RPT:
Functions the same as “Repeat One”
or “Repeat Mode = One.”
ALL RPT:
Functions the same as “Repeat All” or
“Repeat Mode = All.”
ALBM RND*:
Functions the same as “Shuffle
Albums” of the iPod.
SONG RND/RND ON:
Functions the same as “Shuffle Songs”
or “Random Play = On.”
• To cancel repeat play or random play, select
“RPT OFF” or “RND OFF.”
* iPod: Only if you select “ALL” in “ALBUMS” of the main
“MENU.”
21
ENGLISH
EXTERNAL DEVICES
Listening to the other external components
Change the display information
You can connect an external component to the CD changer jack on the rear using the Line Input
Adapter—KS-U57 (not supplied) or AUX Input Adapter—KS-U58 (not supplied).
Preparations:
Make sure “EXT IN” is selected for the external input setting, see page 24.
~ Select “EXT IN.”
Ÿ Turn on the connected component and start playing the source.
! Adjust the volume.
⁄ Adjust the sound as you want (see page 22).
Unit
CD changer jack
(see page 24 of the
”EXT IN” setting)
(see page 24 of the
”EXT IN” setting)
Concept diagram of the external device connection
• For connection, see Installation/Connection manual (separate volume).
: Adapter (separately purchased)
MD player, etc.
MD player, etc.
JVC CD changer, [18]
JVC DAB tuner, [19]
Apple iPod, [20]
JVC D. player, [20]
Loading...