JVC HR-XVC33UM User Manual

Download

Page 1

Filename [XVC33UM_02Cov1.fm]

XVC33UM_02Cov1.fm Page 1 Friday, August 29, 2003 4:59 PM

DVD PLAYER & VIDEO CASSETTE RECORDER

HR-XVC33UM

INSTRUCTIONS

LPT0854-001B

Page 2

Filename [XVC33UM_03Safety.fm]

XVC33UM_01.book Page 2 Monday, August 4, 2003 7:24 PM

Masterpage:Left0

SAFETY FIRST

Dear Customer,

Thank you for purchasing the JVC DVD player & VHS video cassette recorder. Before use, please read the safety information and precautions to ensure safe use of your new unit.

CAUTIONS

WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

The POWER 1 button does not completely shut off mains power from the unit, but switches operating current on and off. “`” shows electrical power standby and “ ! ” shows ON.

CAUTION:

A DVD/VCR IS A CLASS 1 LASER PRODUCT. HOWEVER THIS DVD/VCR USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED. WHEN THIS DVD/VCR IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS DVD/VCR. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

IMPORTANT

It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.

CAUTION

䡲

When you are not using the unit for a long period of time, it is recommended that you disconnect the power cord from the AC outlet.

䡲

Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the AC outlet prior to connecting or disconnecting any signal lead or aerial.

䡲

Changes or modifications not approved by JVC could void user’s authority to operate the equipment.

The rating plate and safety caution are on the rear of the unit.

This unit is produced to comply with Standard IEC

60065.

POWER SYSTEM:

This set operates on voltage of AC 110 – 220Vd, 50/60 Hz with automatic switching.

Use the conversion plug (provided) depending on the type of your AC WALL outlet.

CLASS 1 LASER PRODUCT REPRODUCTION OF LABELS

WARNING LABEL INSIDE OF THE UNIT

Use only discs marked with the following.

DVD (8 cm /12 cm disc)

Video CDs (8 cm /12 cm disc)

Page 2 4 August 2003 6:02 pm

Audio CDs (8 cm /12 cm disc)

SVCD (8 cm /12 cm disc)

Page 3

Filename [XVC33UM_03Safety.fm]

XVC33UM_01.book Page 3 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

●

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

●

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

●

Cassettes marked “VHS” (or “S-VHS”) can be used with this unit. However, S-VHS recording is not possible with this model.

●

This model is equipped with SQPB (S-VHS QUASI PLAYBACK) that makes it possible to play back S-VHS recordings with regular VHS resolution.

●

HQ VHS is compatible with existing VHS equipment.

●

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing users only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear.)

7. DO NOT

place any naked flame sources, such as

lighted candles, on the apparatus.

8. AVOID

violent shocks to the unit during transport.

MOISTURE CONDENSATION

Moisture in the air will condense on the unit when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form in the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the unit turned on for a few hours to let the moisture dry.

TTENTION

To mobile phone users:

Using a mobile phone in the vicinity of the unit may cause picture vibration on the TV screen or change the screen to a blue back display.

On placing the unit:

Some TVs or other appliances generates strong magnetic fields. Do not place such appliance on top of the unit as it may cause picture disturbance.

When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly.

Failure to heed the following precautions may result in damage to the unit, Remote or video cassette.

1. DO NOT

place the unit —

— in an environment prone to extreme temperatures or humidity. — in direct sunlight. — in a dusty environment. — in an environment where strong magnetic fields are generated. — on a surface that is unstable or subject to vibration.

2. DO NOT

block the unit’s ventilation openings or

holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

3. DO NOT

4. DO NOT

place heavy objects on the unit or Remote. place anything which might spill on top of

the unit or Remote.

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

5. DO NOT

expose the apparatus to dripping or

splashing.

6. DO NOT use this equipment in a bathroom or places with water. Also DO NOT

place any containers filled with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top of this unit.

Page 3 4 August 2003 6:02 pm

Page 4

Filename [XVC33UM_04TOC.fm]

XVC33UM_01.book Page 4 Monday, August 4, 2003 7:24 PM

Masterpage:Left

CONTENTS

SAFETY FIRST 2

DISC INFORMATION 5

About Discs ......................................................... 5

INDEX 8

INSTALLING YOUR NEW UNIT 13

Basic Connections ............................................. 13

S-VIDEO Connection (DVD deck only) ............. 14

Component Video Connection

(DVD deck only) ............................................ 15

INITIAL SETTINGS 16

Plug & Play Set .................................................. 16

Monitor Set (DVD deck) .................................... 18

Language ........................................................... 20

Clock Set ........................................................... 24

Tuner Set ........................................................... 26

OPERATIONS ON VCR DECK 28

Basic Playback .................................................. 28

Playback Features .............................................. 29

Basic Recording ................................................ 33

Recording Features ............................................ 34

Express Timer Programing ................................. 36

Satellite Auto Recording .................................... 41

EDITING (VCR DECK) 68

Edit From A Camcorder .....................................68

Edit To Or From Another Video Recorder .......... 69

Dubbing (from DVD to VCR) ............................. 70

EDITING (DVD DECK) 71

Digital Audio Dubbing ...................................... 71

REMOTE 72

Remote Control Functions ................................. 72

Connecting To A Dolby Digital Decoder or

An Amplifier With A Built-in DTS

(DVD deck only) ............................................ 74

SUBSIDIARY SETTINGS 75

Mode Set (VCR deck) ......................................... 75

Mode Set (DVD deck) ........................................ 78

Child Lock .........................................................82

Scan Mode Set (DVD deck) ...............................82

TROUBLESHOOTING 83

QUESTIONS AND ANSWERS 88

SPECIFICATIONS 89

LIST OF TERMS 90

OPERATIONS ON DVD DECK 42

Basic Playback .................................................. 42

Playback Features .............................................. 43

Using the on-screen bar .................................... 48

Parental Lock .................................................... 58

About MP3 Disc ................................................ 62

MP3 Playback ................................................... 63

About JPEG Disc ............................................... 65

JPEG Playback ................................................... 66

Page 4 August 4, 2003 6:54 pm

Page 5

Filename [XVC33UM_05DiscInfo.fm]

XVC33UM_01.book Page 5 Monday, August 4, 2003 7:24 PM

DISC INFORMATION

About Discs

Playable Discs

You can use the discs with the following logos for playback only.

DVD VIDEO Video CD/Super Video CD

Masterpage:Right0

Unplayable Discs

The following types of discs cannot be played using this unit. Do not attempt to play back any kind of disc that is damaged (cracked, warped, or repaired with adhesive tape) or discs in unusual shapes (heart-shaped, octagonal, or other forms). If such discs are accidentally played back, it may cause noise that can lead to speaker damage.

●

CD-ROM discs (including PHOTO-CD)

●

DVD AUDIO discs

●

Super Audio CDs (SACD)

●

DVD-RW discs recorded in VR format

●

DVD-RAM

●

Discs which have a region number other than “4”

Audio CD

CD-DA files

●

The following discs also can be played back.

• DVD-R/RW discs recorded in DVD VIDEO format and finalized

• CD-R/RW discs recorded in Super Video CD, Video CD or Audio CD format and finalized.

• CD-R/RW discs recorded in MP3 format in accordance with the “ISO 9660” format. (See page 62 for details.)

• CD-R/RW discs recorded in JPEG format in accordance with the “ISO 9660” format. (See page 65 for details.)

●

Discs other than the above cannot be played back.

●

Operation and audio quality of this unit are not guaranteed for discs that do not conform to the Compact Disc specification (CD-DA). Before you play back a CD, check for the CD logo and read the notes on the package to confirm that it conforms to the Compact Disc specification.

●

Depending on the intentions of the author of the software, recording conditions of DVD discs and Video CD discs may be restricted. Since this unit plays back discs according to the intentions of the author of the software as indicated on the disc, some functions may not operate as commanded.

●

When switching from the first layer to the second layer of double-layered DVD VIDEO discs, the image and sound may be momentarily distorted. This is not a malfunction.

Region Number

The world is divided into 6 regions for DVD VIDEO discs. DVD VIDEO discs are assigned a region number to indicate which region they may be played back in. A disc cannot be played back on this unit unless the region number of the disc matches that of the unit. The region number for this unit is “4”. Only discs whose region number includes “4” can be played back such as shown below.

Examples of DVD VIDEO labels which can be played back using this unit.

Marks of discs in this instruction manual

Allows operation with a DVD VIDEO disc.

Allows operation with a Video CD disc.

Allows operation with a disc including MP3 files.

Allows operation with a Audio CD disc.

Allows operation with a CD-R/RW disc.

Allows operation with a SVCD disc.

Allows operation with a disc including JPEG files.

Page 5 4 August 2003 6:42 pm

Page 6

Filename [XVC33UM_05DiscInfo.fm]

XVC33UM_01.book Page 6 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

DISC INFORMATION (cont.)

DVD VIDEO Marks

Sometimes marks are printed on a DVD disc and/or on its packaging to indicate information regarding the contents and functions of a disc. Check marks indicating the contents and functions of a disc. Note, however, that in some cases a disc may not include a mark even for a function it supports.

Marks related to video

Mark Description

Number of subtitles

Number of angles

Recorded under the standard 4:3 aspect ratio

Screen includes black bands at top and bottom of image which has a standard 4:3 aspect ratio (letter box)

Video playback is in Wide video mode (16:9) on wide televisions, but in letter box on televisions with standard 4:3 aspect ratio.

File Structure of Discs

DVD VIDEO

Typically, DVD VIDEO discs are made up of larger units called “titles”. Each title has a number (title number) that can be used to select desired titles. Titles are further divided into units called “chapters”. Each chapter has a number (chapter number) that can also be used to select desired chapters. Note that some discs are not divided into titles and chapters.

Title 1 Title 2

Chapter 1 Chapter 2Chapter 1Chapter 3Chapter 2

Audio CD/Video CD

Typically, Audio CD discs are divided into separate tracks each containing one song. Each track is assigned a number. For example, the third track is Track 3. The same is true for Video CD discs.

Track 1 Track 4Track 3Track 2

NOTE:

Video CD discs that support Playback Control (PBC)

The still image or motion image which follows a menu screen is called a “scene”. Each scene has a scene number. For more details, refer to “Locating a desired scene using the menu of the Video CD with PBC” (

墌

pg. 43).

Video playback is in Wide video mode (16:9) on wide televisions, but pan and scan is used on televisions with standard 4:3 aspect ratio (either the left or right side of the image is cut-out).

Marks related to audio

Mark Description

Number of audio tracks

Dolby Digital mark Dolby Laboratories has developed a digital surround system for the home. This mark indicates that you may enjoy 5.1channel audio (front left and right, center, rear left and right, and a channel for LFE (Low-Frequency Effects)).

DTS (Digital Theater System) You can enjoy DTS audio if you connect the amplifier with a built-in DTS decoder to the DIGITAL AUDIO OUT connector of the unit.

Page 6 4 August 2003 6:42 pm

Page 7

Filename [XVC33UM_05DiscInfo.fm]

XVC33UM_01.book Page 7 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Placing a Disc

Open the disc tray.

OPEN/CLOSE

Press disc tray.

●

Pressing the button again closes the disc tray.

●

Do not block the disc tray with your hand while it is opening or closing as this may result in hardware failure.

●

Do not place unplayable discs or any object other than a disc in the disc tray.

●

Do not press down strongly on the disc tray or place any heavy objects on it.

Place the disc.

Place the disc in the disc tray with the label side facing up.

●

Since disc size changes depending on the disc to be played back, be sure to correctly align the disc with the grooves for its size. If the disc is not in its groove, it may be scratched or otherwise damaged.

●

To insert an 8 cm disc, place it according to the inner groove.

(x) on the DVD deck to open the

Care and Handling of Discs

How to handle discs

When handling a disc, do not touch the surface of the disc. Since discs are made of plastic, they are easily damaged. If a disc gets dirty, dusty, scratched or warped, the images and sound will not be picked up correctly, and such a disc may cause the unit to malfunction.

Label side

Do not damage the label side, stick paper to or use any adhesive on its surface.

Storage

Make sure that discs are kept in their cases. If discs are piled on top of one another without their protective cases, they can be damaged. Do not put discs in a location where they may be exposed to direct sunlight, or in a place where the humidity or temperature is high. Avoid leaving discs in your car!

Maintenance of discs

If there are fingerprints or other dirt adhering to a disc, wipe with a soft dry cloth, moving from the center outwards. If a disc is difficult to clean, wipe with a cloth moistened with water. Never use record cleaners, petrol, alcohol or any anti-static agents.

CAUTION

Sometimes during playback, noise or images may be garbled. This is sometimes due to the disc. (It may not be up to industry standards.) These symptoms are caused by the discs, not by the malfunction of the unit.

Page 7 4 August 2003 6:42 pm

Page 8

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 8 Monday, August 4, 2003 7:24 PM

FRONT VIEW

Masterpage:Left0

INDEX

Power Button (POWER (1)) 墌pg. 18

VCR Indicator 墌pg. 28, 33

VHS Cassette Loading Slot

VCR/DVD Button 墌pg. 28, 33, 42

Disc Tray

Stop Button (STOP (8)) 墌pg. 28, 33, 42

DVD Indicator 墌pg. 42

Play Button (PLAY (4)) 墌pg. 28, 42

DVD Open/Close Button (OPEN/CLOSE (x))

pg. 42

墌

VHS Eject Button (EJECT (x)) 墌pg. 28, 33

Video/Audio Input Connectors (VIDEO/AUDIO)

pg. 68

墌

Remote Sensor

Front Display Panel 墌pg. 10

Record Button (REC (7)) 墌pg. 33

Rewind Button (REW (3)) 墌pg. 28, 29, 44

Fast Forward Button (FF (5)) 墌pg. 28, 29, 44

Channel Button (CH +/–) 墌pg. 33

Progressive Scan Button (PROGRESSIVE SCAN)

pg. 82

墌

Page 8 4 August 2003 6:42 pm

Page 9

Filename [XVC33UM_06Index.fm]

XVC33UM_06Index.fm Page 9 Friday, August 29, 2003 5:00 PM

REAR VIEW

Masterpage:Right-No-Heading

Region Number Label 墌pg. 5

AC Power Cord 墌pg. 13

S-video Output Connector (S VIDEO OUTPUT)*

pg. 14

墌

* This connector is for DVD deck only.

Audio/Video Input Connectors (AUDIO/VIDEO

INPUT) 墌pg. 41, 68 Audio/Video Output Connectors (AUDIO/

VIDEO OUTPUT) 墌pg. 13, 14, 15, 69 Antenna Input Connector (VHF/UHF IN)

pg. 13

墌

Digital Audio Output Connector

(DIGITAL AUDIO OUT) 墌pg. 71 Audio Output Connectors (AUDIO OUTPUT

(L/R))*

* These are analogue audio output connectors for DVD deck only.

Component Video Output Connectors

(COMPONENT VIDEO OUT) 墌pg. 15 Remote Pause Connector (REMOTE PAUSE)

pg. 68

墌

Antenna Output Connector (VHF/UHF OUT)

pg. 13

墌

Page 9 29 August 2003 5:00 pm

Page 10

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 10 Monday, August 4, 2003 7:24 PM

FRONT DISPLAY PANEL

Masterpage:Left+

INDEX (cont.)

Progressive Mode Indicator 墌pg. 82

“Timer” Indicator (VCR deck only) 墌pg. 37

Satellite Auto Recording Indicator (N) (VCR deck only) 墌pg. 41

Channel/Clock Mode Display (F-1 or L-1) (VCR deck only) Counter Display (VCR deck) Tape Speed (SP/EP) (VCR deck only) Multi-information window* (DVD deck)

* The current group/title/track/chapter number(s), time and status

information.

VCR Mode Indicator

VCR Indicator 墌pg. 34

Cassette Type Indicator (VCR deck only)

Channel Mode Indicator (CH)

Remain Display 墌pg. 35

DVD Mode Indicator

Page 10 4 August 2003 6:42 pm

Page 11

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 11 Monday, August 4, 2003 7:24 PM

ON-SCREEN DISPLAY (VCR deck)

If you press appear on the TV screen. For On-screen display for DVD deck, refer to “Using the on-screen bar” (墌pg. 48).

DISPLAY

on the Remote when “SUPERIMPOSE” is set to “ON” (墌pg. 76), various operational indicators

Masterpage:Right-No-Heading

Operation Mode Indicators

Tape Speed (SP/EP)

Tape Position Indicator

The tape position indicator appears on the TV screen when you press or FF (5) from the Stop mode or perform an Index Search. ( position of “q” in relation to “0” (beginning) or “+” (end) shows you where you are on the tape.

墌

pg. 30) The

REW

(3)

Beginning End

NOTE:

Depending on the type of tape being used, the tape position indicator may not appear correctly.

Index number 墌pg. 30

Tape Remaining Time Indicator 墌pg. 35

Counter Display

Audio Mode Display 墌pg. 32

SAP Indicator 墌pg. 35

Stereo Program Indicator 墌pg. 35

Day/Clock Display

Channel Position Number/Auxiliary Input Indicator (F-1 or L-1)

“Cassette Loaded” Mark

To recall an indication

DISPLAY

Press

●

All indications corresponding to the current status are displayed for 5 seconds. After that, the counter information and RECORD/PAUSE if in the Record Pause mode, remain on the screen.

DISPLAY

Press

●

The RECORD/PAUSE indication remains on the screen.

again to clear the display.

Page 11 4 August 2003 6:42 pm

Page 12

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 12 Monday, August 4, 2003 7:24 PM

REMOTE

Buttons with a small dot on the left side of the name can also be used to operate your TV. (

VCR Button 墌pg. 28, 33

TV/VCR/DVD switch 墌pg. 18

Menu Button (MENU) 墌pg. 43

SP/EP Button 墌pg. 33 Top Menu Button (TOP MENU) 墌pg. 43

Stop Time Button (STOP +/–) 墌pg. 36 Display Button (PLAY SETUP) 墌pg. 48 Title Button (TITLE) 墌pg. 64

Start Time Button (START +/–) 墌pg. 36 Repeat Button (REPEAT) 墌pg. 50, 64, 67 Zooming Button (ZOOM) 墌pg. 45

Number Keys 墌pg. 27, 33, 64

Daily Button (DAILY) 墌pg. 37

Counter Reset Button (C.RESET) 墌pg. 35 Cancel Button (CANCEL) 墌pg. 39 10 Button

Play Button (PLAY (4)) 墌pg. 28, 42

Rewind Button (REW (3)) 墌pg. 28, 29, 44

Stop Button (STOP (8)) 墌pg. 28, 33, 42

Record Button (REC (7)) 墌pg. 33

墌

pg. 73)

Masterpage:Left+

INDEX (cont.)

Reverse Skip/Index Button (SKIP/INDEX (2))

pg. 30, 43

墌

Review Button ( ) 墌pg. 30

Button 墌pg. 18

TV/VCR Channel Button (TV/VCR CH +/–)

pg. 73

墌

Set Up Menu Button (SET UP MENU) 墌pg. 18

3D-Phonic Button (3D-PHONIC) 墌pg. 46

TV Volume Button (TV VOL+/–) 墌pg. 73

DVD Button 墌pg. 42

Power Button (POWER (1)) 墌pg. 18

TV Muting Button (MUTE) 墌pg. 73 Audio Monitor Button (A.MONITOR)

pg. 32, 56, 57

墌

TV/VCR Button 墌pg. 34

Date Button (DATE +/–) 墌pg. 36 Subtitle Button (SUB TITLE) 墌pg. 54 Angle Button (ANGLE) 墌pg. 55

* With this button, you can also adjust the brightness of front

display panel. +: brightens the display –: darkens the display

Channel Button (CH +/–) 墌pg. 33

Programing Button (PROG.) 墌pg. 36

Timer Button (TIMER) 墌pg. 37

Weekly Button (WEEKLY) 墌pg. 37

Program Check Button (PROG. CHECK)

pg. 38

墌

Return Button (RETURN) 墌pg. 43

Satellite Auto Recording Button (REC LINK)

pg. 41

墌

+10 Button

Auxiliary Button (AUX) 墌pg. 68

Fast Forward Button (FF (5)) 墌pg. 28, 29, 44

Pause Button (PAUSE (9)) 墌pg. 29, 33

Forward Skip/Index Button (SKIP/INDEX (6))

pg. 30, 43

墌

OK Button 墌pg. 18

j k l

Button 墌pg. 18 Display Button (DISPLAY) 墌pg. 35 Skip Search Button (SKIP SEARCH) 墌pg. 30 DVD Picture Button (DVD PICTURE) 墌pg. 47

How To Use

Before use, insert two AA size batteries into the Remote with the polarity ( and ) matched correctly as indicated on the battery compartment or on the lid.

The Remote can operate most of your unit’s functions, as well as basic functions of TV sets of JVC and other brands.

墌

(

pg. 73)

●

Point the Remote toward the remote sensor.

●

The maximum operating distance of the remote control is about 8 m.

NOTE:

If the Remote doesn’t work properly, remove its batteries, wait a short time, replace the batteries and then try again.

Page 12 4 August 2003 6:42 pm

Page 13

Filename [XVC33UM_06Index.fm]

XVC33UM_06Index.fm Page 13 Tuesday, September 9, 2003 9:27 AM

INSTALLING YOUR NEW UNIT

Basic Connections

Antenna or Cable

Coaxial cable

Flat feeder

Matching transformer (not supplied)

AC Outlet

AC Power Cord

Back of unit

VIDEO OUTPUT

PCM/STREAM

COAXIALOPTICAL

AUDIO

OUTPUT

VHF/UHF IN

Masterpage:Right0

Connect the unit to TV.

The connection method you use depends on the type of TV you have.

RF Connection

To connect to a TV with NO AV input connectors —

Disconnect the TV antenna from the TV.

Connect the TV antenna cable to the VHF/UHF IN

connector on the rear panel of the unit. Connect the supplied RF cable between the VHF/UHF

OUT connector on the rear panel of the unit and the TV’s antenna terminal.

AV C onnection

To connect to a TV with AV input connectors —

Connect the antenna, unit and TV as per “RF

Connection”. Connect an optional audio/video cable between the

AUDIO/VIDEO OUTPUT connectors on the rear panel of the unit and the TV’s audio/video input connectors.

● Set your TV to AV mode.

● For switching the TV’s mode, refer to the instruction manual of

your television.

● To obtain high-quality pictures, you can also use the S-VIDEO connection or Component Video Connection. (DVD deck only) (

pg. 14, 15)

墌

Audio/video cable

(not supplied)

To Audio/video

input connectors

It’s essential that your unit be properly connected.

THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED.

Check the contents.

Make sure the package contains all of the accessories listed in “SPECIFICATIONS” on page 89.

Situate the unit.

Place the unit on a stable, horizontal surface.

VHF/UHF OUT

RF cable

(supplied)

To 75 ohm Te rm i na l

Connect the unit to power source.

Plug the end of the AC power cord into an AC outlet.

Set the VCR channel.

The VCR channel is the channel on which you can watch the picture from the unit on the TV when only using RF connection. With RF connection, set the VCR channel to “3 CH” or “4 CH”.

● The VCR channel is preset to “3 CH”. Set to “4 CH” if the Channel 3 is used for broadcasting in your area.

With AV connection, set the VCR channel to “– CH” (off). To set the VCR channel, perform the following steps:

Before performing the following steps:

Make sure there is no cassette inserted in the unit.

●

Make sure the unit is turned on, then press

●

on the unit or

DVD

VCR indicator lights up.

When the unit is turned off, press

for more than 5 seconds. “3 CH” appears on the front display panel. Press

or “– CH” (off), then press OK.

● If Plug&Play or Tuner setting has not previously been performed, the Language Select screen appears and Plug&Play takes place automatically.

on the Remote to select “3 CH”, “4 CH”

CH +/–

on the Remote so that the

VCR

STOP

VCR/

(8) on the unit

Page 13 9 September 2003 9:26 am

Page 14

Filename [XVC33UM_06Index.fm]

XVC33UM_06Index.fm Page 14 Tuesday, September 9, 2003 9:27 AM

S-VIDEO Connection

(DVD deck only)

TTENTION

Be sure to connect the unit’s VIDEO OUTPUT (DVD/ VCR) connector to the TV’s VIDEO input connector.

Antenna or Cable

Coaxial cable

Flat feeder

Matching transformer (not supplied)

AC outlet

Back of unit

S-Video cable (not supplied)

S VIDEO OUTPUT

AC power cord

PCM/STREAM

COAXIALOPTICAL

VIDEO OUTPUT

Audio/video

cable

(not supplied)

AUDIO OUTPUT

VHF/UHF IN

VHF/UHF

OUT

Masterpage:Left+

INSTALLING YOUR NEW UNIT (cont.)

To connect to a TV with S-VIDEO/AUDIO input connectors . . .

Connect the unit to TV.

Connect the antenna, unit and TV as per “AV

Connection”. (墌pg. 13) Connect the unit’s S VIDEO OUTPUT (DVD)

connector to the TV’s S-VIDEO input connector.

Connect the unit to power source.

Plug the end of the AC power cord into an AC outlet.

Set the VCR channel to off.

Before performing the following steps:

Make sure there is no cassette inserted in the unit.

●

Make sure the unit is turned on, then press

●

on the unit or

DVD

VCR indicator lights up.

When the unit is turned off, press

for more than 5 seconds. “3 CH” appears on the front display panel. Press

then press OK.

● If Plug&Play or Tuner setting has not previously been performed, the Language Select screen appears and Plug&Play takes place automatically.

on the Remote to select “– CH” (off),

CH +/–

on the Remote so that the

VCR

STOP

VCR/

(8) on the unit

NOTES:

● You can obtain high-quality S-VHS pictures when you play back discs on the DVD deck.

● If your TV is not stereo-capable, use the unit’s AUDIO OUTPUT connectors to connect to an audio amplifier for Hi-Fi stereo sound reproduction.

● To operate the unit with your TV using the S-VIDEO connection, set your TV to its AV mode. You can also use the

button on the unit’s Remote to set your TV to the AV

TV/VCR

mode. (

● For switching the TV’s mode, refer to the instruction manual of your television.

墌

pg. 73)

RF cable

(supplied)

To S-VIDEO input

connector

Page 14 9 September 2003 9:26 am

To 75 ohm Te r mi n a l

Page 15

Filename [XVC33UM_06Index.fm]

XVC33UM_06Index.fm Page 15 Tuesday, September 9, 2003 9:27 AM

Component Video Connection

(DVD deck only)

Masterpage:Right-No-Heading

To connect to a TV with component video input connectors . . .

Connect the unit to TV.

Connect the aerial, unit and TV as per “AV

Connection”. (墌pg. 13) Connect the unit’s COMPONENT VIDEO OUT

connectors to the TV’s component video input connectors.

TTENTION

Be sure to connect the unit’s VIDEO OUTPUT (DVD/ VCR) connector to the TV’s VIDEO input connector.

Antenna or Cable

Coaxial cable

Flat feeder

Matching transformer (not supplied)

AC outlet

Back of unit

Component Video cable

(not supplied)

AC power cord

PCM/STREAM

COAXIALOPTICAL

COMPONENT

VIDEO OUT

VIDEO OUTPUT

Audio/Video

cable

(not supplied)

AUDIO

OUTPUT

VHF/UHF IN

VHF/UHF

OUT

Connect the unit to power source.

Plug the end of the AC power cord into an AC outlet.

Set the VCR channel to off.

Before performing the following steps:

Make sure there is no cassette inserted in the unit.

●

Make sure the unit is turned on, then press

●

on the unit or

DVD

VCR indicator lights up.

When the unit is turned off, press

for more than 5 seconds. “3 CH” appears on the front display panel. Press

then press OK.

● If Plug&Play or Tuner setting has not previously been performed, the Language Select screen appears and Plug&Play takes place automatically.

on the Remote to select “– CH” (off),

CH +/–

on the Remote so that the

VCR

STOP

VCR/

(8) on the unit

NOTES:

● You can obtain high-quality component video pictures when you play back discs on the DVD deck.

● If your TV is not stereo-capable, use the unit’s AUDIO OUTPUT connectors to connect to an audio amplifier for Hi-Fi stereo sound reproduction.

● To operate the unit with your TV using the Component Video connection, set your TV to its AV mode. You can also use the

button on the unit’s Remote to set your TV to the AV

TV/VCR

mode. (

● For switching the TV’s mode, refer to the instruction manual of your television.

墌

pg. 73)

RF cable

(supplied)

To Component Video

Input connector

Page 15 9 September 2003 9:26 am

To 75 ohm Te rm i na l

Page 16

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 16 Monday, August 4, 2003 7:24 PM

Plug & Play Set

Auto Channel Set

The Plug & Playn Set simplifies installation by guiding you through the procedures of setting the language, clock and tuner channels — simply follow the on-screen menus that appear.

Masterpage:Left0

INITIAL SETTINGS

Before starting, make sure of the following:

●

The TV aerial cable should be connected to the unit.

●

The unit’s AC power cord should be connected to a AC outlet.

●

The TV should be set to its AV mode (with AV, S-VIDEO or Component Video connection ( channel (with RF connection

●

Slide the

Press 1 on the unit or Remote. The Language Select screen appears on the TV screen.

Press rt to move the highlight bar (arrow) to the language of your choice, then press OK or e.

●

The Clock Set screen appears.

TV/VCR/DVD

Turn on the unit.

Select the language.

墌

pg. 13, 14, 15) or VCR

墌

switch to the right.

pg. 13).

LANGUAGE SELECT

PRESS ( , ), THEN (OK) PRESS (MENU) TO END

ENGLISH

ESPAÑOL

NOTE:

The selected language is only available on the screen for VCR deck. Set manually the on-screen language for the DVD deck.

墌

(

pg. 21)

Set the time.

Press rt to set the hour, then press OK or e.

●

Press and hold rt to change the time by 30 minutes.

Set the date.

Press rt to set the date, then press OK or e.

●

Press and hold rt to change the date by 15 days.

Set the year.

Press rt to set the year.

CLOCK SET

TIME DATE YEAR

– –:– –AM 1/ 1 03

PRESS ( , ), THEN (OK) PRESS (MENU) TO END

Page 16 4 August 2003 6:42 pm

Page 17

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 17 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Start Auto Channel Set.

Press

DO NOT press any button on the unit or Remote while Auto Channel Set is in progress.

●

Receivable channels in your area are automatically assigned to the

CH +/–

receivable channels are skipped.

●

When Auto Channel Set is completed, “SCAN COMPLETED” will appear on the TV screen. If “SCAN COMPLETED –NO SIGNAL–” is displayed on the TV screen, make sure that the aerial cable is connected to the unit properly and press OK on the Remote. The unit will try Auto Channel Set again.

AUTO CHANNEL SET

buttons, and non-

SCANNING...

PRESS (MENU) TO END

NOTE:

If there is a power cut, or if you press 1 or Auto Channel Set is in progress, Auto Channel Set will be interrupted; be sure to turn off the unit power once and try again from stepA.

SET UP MENU

while

TTENTION

If you perform Auto Channel Set successfully during installation, there's no need to separately perform the Language Select, Clock Set or Channel Set procedures, but if adjustments become necessary, they can be performed as follows:

●

Language setting

●

Tuner setting

●

Clock setting

墌

pg. 26

pg. 24

pg. 20

Page 17 4 August 2003 6:42 pm

Page 18

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 18 Monday, August 4, 2003 7:24 PM

Monitor Set

Turn on the unit.

POWER

Press

Masterpage:Left+

INITIAL SETTINGS (cont.)

(1).

(DVD deck)

You can select the monitor type depending the TV used when you play back DVD VIDEO discs recorded for wide-screen TVs.

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Select the DVD deck.

On the unit

VCR/DVD

Press lights up.

On the Remote

DVD

Press

Access the DVD Set Up menu screen.

Press

Press we to select “PICTURE”.

Select the mode.

Press rt to move 0 to “MONITOR TYPE”, then press OK.

repeatedly so that the DVD indicator

so that the DVD indicator lights up.

SET UP MENU

PICTURE

MONITOR TYPE

PICTURE SOURCE

SCREEN SAVER

MP3 / JPEG

SELECT

USE TO SELECT, USE OK TO CONFIRM. TO EXIT, PRESS [SET UP MENU].

PICTURE

MONITOR TYPE

PICTURE SOURCE

SCREEN SAVER

MP3 / JPEG

SELECT

USE TO SELECT, USE OK TO CONFIRM. TO EXIT, PRESS [SET UP MENU].

4:3LB

AUTO

MP3

4:3LB

AUTO

MP3

Select the mode setting.

Press rt to select the desired setting, then press OK.

Return to the normal screen.

SET UP MENU

Press

Page 18 4 August 2003 6:42 pm

Page 19

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 19 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

* The default setting is

MONITOR TYPE

16:9 NORMAL (Wide television conversion)

Select this when the aspect ratio of your TV is 16:9 (wide TV).

16:9 AUTO (Wide television conversion)

Select this when the aspect ratio of your TV is fixed to 16:9 (wide TV). The unit automatically adjusts the screen width of the output signal correctly when playing back a picture whose aspect ratio is 4:3.

4:3 LB

(Letter Box conversion)

Select this when the aspect ratio of your TV is 4:3 (conventional TV). While viewing a wide screen picture, the black bars appear on the top and the bottom of the screen.

4:3 PS (Pan&Scan)

Select this when the aspect ratio of your TV is 4:3 (conventional TV). While viewing a wide screen picture, the black bars do not appear; however, the left and right edges of the pictures will not be shown on the screen.

bold

in the table below.

Pan&Scan/Letter Box

In general, DVD VIDEO disc are produced for a wide-screen TV with 16:9 aspect ratio. Material with this ratio will not fit to a TV with 4:3 aspect ratio. There are two styles to display the image, “Pan&Scan” (PS) and “Letter Box” (LB).

Pan&Scan

The right and left side of the image are cut off. The image fills the screen.

Letter Box

Black bands appear at the top and bottom of the image. The image itself appears in 16:9 aspect ratio.

Page 19 4 August 2003 6:42 pm

Page 20

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 20 Monday, August 4, 2003 7:24 PM

Language

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Masterpage:Left+

INITIAL SETTINGS (cont.)

On-screen Language Set (VCR deck)

Use language setting only if the language have not been set correctly by the Plug&Play setting. The default setting is “ESPAÑOL”.

Turn on the unit.

POWER

Press

On the unit

VCR/DVD

Press lights up.

On the Remote

VCR

Press

SET UP MENU

Press

(1).

Select the VCR deck.

repeatedly so that the VCR indicator

so that the VCR indicator lights up.

Access the Main Menu screen.

Access the Initial Set screen.

Press rt to move the highlight bar (arrow) to “INITIAL SET”, then press OK or e.

Select the language.

Press rt to move the highlight bar (arrow) to “LANGUAGE”, then press

or e repeatedly until the

desired language is selected.

Return to the normal screen.

SET UP MENU

Press

Page 20 4 August 2003 6:42 pm

Page 21

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 21 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

On-screen Language Set (DVD deck)

This DVD deck offers you the choice to view on-screen messages in 3 different languages. You can change the language setting manually as required.

Turn on the unit.

POWER

Press

On the unit

VCR/DVD

Press lights up.

On the Remote

DVD

Press

Press we to select “LANGUAGE”.

(1).

Select the DVD deck.

repeatedly so that the DVD indicator

so that the DVD indicator lights up.

Access the DVD Set Up menu screen.

SET UP MENU

LANGUAGE

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ON SCREEN LANGUAGE

ENGLISH

OFF

ENGLISH

SELECT

USE TO SELECT, USE OK TO CONFIRM. TO EXIT, PRESS [SET UP MENU].

Select the mode.

Press rt to move 0 to “ON SCREEN LANGUAGE”, then press OK.

Select the mode setting.

LANGUAGE

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ON SCREEN LANGUAGE

SELECT

USE TO SELECT, USE OK TO CONFIRM. TO EXIT, PRESS [SET UP MENU].

ENGLISH

OFF

ENGLISH

Press rt to select the desired setting, then press OK.

Return to the normal screen.

SET UP MENU

Press

Page 21 4 August 2003 6:42 pm

Page 22

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 22 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

INITIAL SETTINGS (cont.)

Menu/Audio/Subtitle Language Set (DVD deck only)

Some DVD discs contain the DVD menu display, audio, subtitle in the multiple languages. With these discs, you can set the default language as you like.

●

The procedure shows how to set “MENU LANGUAGE” on the DVD Set Up menu screen as an example.

Turn on the unit.

POWER

Press

On the unit

VCR/DVD

Press lights up.

On the Remote

DVD

Press

(1).

Select the DVD deck.

repeatedly so that the DVD indicator

so that the DVD indicator lights up.

Access the DVD Set Up menu screen.

A B

Press rt to move 0 to “MENU LANGUAGE”, then press OK.

SET UP MENU

Press Press we to select “LANGUAGE”.

Select the mode.

Select the mode setting.

LANGUAGE

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ON SCREEN LANGUAGE

SELECT

USE TO SELECT, USE OK TO CONFIRM. TO EXIT, PRESS [SET UP MENU].

LANGUAGE

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ON SCREEN LANGUAGE

SELECT

USE TO SELECT, USE OK TO CONFIRM. TO EXIT, PRESS [SET UP MENU].

ENGLISH

OFF

ENGLISH

OFF

ENGLISH

Press rt to select the desired setting, then press OK.

●

See “Language Code List” (

Return to the normal screen.

SET UP MENU

Press

墌

pg. 23).

NOTE:

When the selected language is not available on the disc, the disc’s default menu language is played back.

Page 22 4 August 2003 6:42 pm

Page 23

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 23 Monday, August 4, 2003 7:24 PM

Language Code List

Masterpage:Right 3Column

AA AB AF AM AR AS AY AZ BA BE BG BH BI BN BO BR CA CO CS CY DA DZ EL EO ET EU FA FI FJ FO FY GA GD GL GN GU HA HI HR HU HY IA IE

Afar Abkhazian Afrikaans Ameharic Arabic Assamese Aym ara Azerbaijani Bashkir Byelorussian Bulgarian Bihari Bislama Bengali, Bangla Tibet an Breton Catalan Corsican Czech Welsh Danish Bhutani Greek Esperanto Estonian Basque Persian Finnish Fiji Faroes e Frisian Irish Scots Gaelic Galician Guarani Gujarati Hausa Hindi Croatian Hungarian Armenian Interlingua Interlingue

IK IN IS IW JI JW KA KK KL KM KN KO KS KU KY LA LN LO LT LV MG MI MK ML MN MO MR MS MT MY NA NE NL NO OC OM OR PA PL PS PT QU RM

Inupiak Indonesian Icelandic Hebrew Yiddish Javanese Georgian Kazakh Greenlandic Cambodian Kannada Korean (KOR) Kashmiri Kurdish Kirghiz Latin Lingala Laothian Lithuanian Latvian, Lettish Malagasy Maori Macedonian Malayalam Mongolian Moldavian Marathi Malay (MAY) Maltese Burmese Nauru Nepali Dutch Norwegian Occitan (Afan) Oromo Oriya Pa nj ab i Polish Pashto, Pushto Portuguese Quechua Rhaeto-Romance

RN RO RU RW SA SD SG SH SI SK SL SM SN SO SQ SR SS ST SU SV SW TA TE TG TH TI TK TL TN TO TR TS TT TW UK UR UZ VI VO WO XH YO ZU

Kirundi Rumanian Russian Kinyarwanda Sanskrit Sindhi Sangho Serbo-Croatian Singhalese Slovak Slovenian Samoan Shona Somali Albanian Serbian Siswati Sesotho Sundanese Swedish Swahili Ta m il Te l ug u Tajik Thai Tig ri nya Tu r km e n Tagalog Setswana To n ga Tu r ki s h Tsonga Ta t ar Tw i Ukrainian Urdu Uzbek Vietnamese Volapuk Wolof Xhosa Yoruba Zulu

Page 23 4 August 2003 6:42 pm

Page 24

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 24 Monday, August 4, 2003 7:24 PM

Clock Set

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Masterpage:Left+

INITIAL SETTINGS (cont.)

Perform clock setting only if the clock has not been set correctly by the Plug&Play setting.

Turn on the unit.

POWER

Press

On the unit

VCR/DVD

Press lights up.

On the Remote

VCR

Press

SET UP MENU

Press

(1).

Select the VCR deck.

repeatedly so that the VCR indicator

so that the VCR indicator lights up.

Access the Main Menu screen.

Access the Initial Set screen.

Press rt to move the highlight bar (arrow) to “INITIAL SET”, then press OK or e.

Access the Clock Set screen.

Press rt to move the highlight bar (arrow) to “CLOCK SET”, then press OK or e.

Page 24 4 August 2003 6:42 pm

Page 25

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 25 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Set the time.

Press rt to set the hour, then press OK or e.

●

Press and hold rt to change the time by 30 minutes.

Set the date.

Press rt to set the date, then press OK or e.

●

Press and hold rt to change the date by 15 days.

Set the year.

Press rt to set the year.

CLOCK SET

TIME DATE YEAR

– –:– –AM 1/ 1 03

PRESS ( , ), THEN (OK) PRESS (MENU) TO END

Start clock.

SET UP MENU

Press

To make corrections any time during the process

Press OK or e repeatedly until the item you want to change blinks, then press rt.

and normal screen appears.

Page 25 4 August 2003 6:42 pm

Page 26

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 26 Monday, August 4, 2003 7:24 PM

Tuner Set

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Masterpage:Left+

INITIAL SETTINGS (cont.)

Auto Channel Set

Perform Auto Channel Set only if channels have not been set correctly by the Plug&Play setting.

Turn on the unit.

POWER

Press

On the unit

VCR/DVD

Press lights up.

On the Remote

VCR

Press

SET UP MENU

Press

(1).

Select the VCR deck.

repeatedly so that the VCR indicator

so that the VCR indicator lights up.

Access the Main Menu screen.

INFORMATION

The unit selects the correct band (TV or CATV) automatically during Auto Channel Set. The selected band will be displayed on the right side of “BAND” on the Tuner Set screen.

Access the Tuner Set screen.

Press rt to move the highlight bar (arrow) to “TUNER SET”, then press OK or e.

Perform Auto Channel Set.

Press rt to move the highlight bar (arrow) to “AUTO CHANNEL SET”, then press OK or e. You can automatically set the receivable channels in your area in the order of their frequencies.

●

When Auto Channel Set is complete, “SCAN COMPLETED” appears on the TV screen.

●

If the scan was unsuccessful, “SCAN COMPLETED–NO SIGNAL–” appears on screen. Check the connections and start again.

Return to the normal screen.

SET UP MENU

Press

Page 26 4 August 2003 6:42 pm

Page 27

Filename [XVC33UM_06Index.fm]

XVC33UM_01.book Page 27 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Manual Channel Set

You can add the channels you want or delete the channels you do not want manually.

Turn on the unit.

POWER

Press

On the unit

VCR/DVD

Press lights up.

On the Remote

VCR

Press

SET UP MENU

Press

(1).

Select the VCR deck.

repeatedly so that the VCR indicator

so that the VCR indicator lights up.

Access the Main Menu screen.

Access the Tuner Set screen.

Press rt to move the highlight bar (arrow) to “TUNER SET”, then press OK or e.

Access the Manual Channel Set screen.

Press rt to move the highlight bar (arrow) to “MANUAL CHANNEL SET”, then press OK or e.

Add or skip the desired channels.

To add channels

Press the input a channel number you want to add.

Press OK or e to set to “ADD”.

Repeat A to B to add other channels.

To skip channels

Press rt or the number you want to skip.

Press OK or e to set to “SKIP”.

Repeat A and B to skip other channels.

number keys

to select a channel

Return to the normal screen.

SET UP MENU

Press

Page 27 4 August 2003 6:42 pm

Page 28

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 28 Monday, August 4, 2003 7:24 PM

Basic Playback

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Masterpage:Left0

OPERATIONS ON VCR DECK

Load a cassette.

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointed toward the unit.

●

Do not apply too much pressure when inserting.

●

If the record safety tab has been removed, playback begins automatically. Although the DVD deck is selected, the VCR deck is selected automatically if the DVD deck is in stop mode.

●

The unit’s power comes on automatically and the counter is reset to 0:00:00.

Select the VCR deck.

On the unit

VCR/DVD

Press lights up.

On the Remote

VCR

Press

repeatedly so that the VCR indicator

so that the VCR indicator lights up.

Clean the video heads using a dry cleaning cassette — ECL-3F — when:

●

Rough, poor picture appears while a tape is played back.

●

The picture is unclear or no picture appears.

●

“USE CLEANING CASSETTE” appears on the screen (only with “SUPERIMPOSE” set to “ON”). (

墌

pg. 76)

NOTE:

The heads get dirty in the following cases:

●

in an environment prone to extreme temperature or humidity

●

in a dusty environment

●

flaw, dirt or mold on video tapes

●

continuous usage for a long time

Find the program start point.

If the tape is advanced past the start point, press (3). To go forward, press FF (5).

Start playback.

PLAY

Press

Press to remove the cassette.

(4).

Stop playback.

STOP

(8). Then press

EJECT

(x) on the VCR deck

REW

Usable cassettes

Full-Size VHS

T-30 (ST-30**) T-60 (ST-60**) T90 T-120 (ST-120**) T-160 (ST-160**) ST-210**

Compact VHS*

TC-20 (ST-C20**) TC-30 (ST-C30**) TC-40 (ST-C40**) * Compact VHS camcorder recordings can be played on

this unit. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette.

** This unit can record on regular VHS and Super VHS

cassettes. However, it will record regular VHS signals only.

• S-VHS recording is not possible with this unit.

This unit is equipped with SQPB (S-VHS QUASI PLAYBACK) that lets you watch tapes recorded in the S-VHS format and the SP mode with regular VHS resolution.

●

SQPB does not deliver Super VHS resolution.

Page 28 4 August 2003 6:42 pm

Page 29

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 29 Monday, August 4, 2003 7:24 PM

Playback Features

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Masterpage:Right-No-Heading

Still Picture/Frame-By-Frame Playback

Pause during playback.

PAUSE

Press

●

If there is vertical jitter, press the picture.

Activate frame-by-frame playback.

Press

(9).

PAUSE

(9) to advance a still picture.

CH +/–

on the Remote to correct

Slow Motion

Pause during playback.

PAUSE

Press

Activate slow motion playback.

Press and hold Press picture.

●

The speed changes for each direction by pressing and FF (5) repeatedly.

(9).

PAUSE

(9) for 2 seconds, then release.

PAUSE

(9) and release again to return to still

REW

(3)

ATTENTION

In the search, still, slow-motion or frame-by-frame playback mode,

●

the picture will be distorted.

●

the noise bars will appear.

●

there may be a loss of colour.

●

you cannot hear the sound.

NOTE:

During slow motion playback, some noise may appear on the TV screen. Press

CH +

or – on the Remote to eliminate the noises.

High-Speed (Turbo) Search

During playback, press FF (5) for forward high-speed search, or

●

The speed changes for each direction by pressing and FF (5) repeatedly. When pressing FF (5): (SP): +5x{+7x (EP): +11x{+21x When pressing Once normal playback speed. After this process, each press of (3) changes the search speed between –5x and –7x in SP mode, –11x and –21x in EP mode. (SP): –1x]–5x{–7x (EP): –1x]–11x{–21x

To resume normal playback, press

REW

(3) for reverse high-speed search.

REW

(3) is pressed, reverse search starts in –1x

(3):

PLAY

(4).

REW

(3)

REW

Page 29 4 August 2003 6:42 pm

Page 30

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 30 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

OPERATIONS ON VCR DECK (cont.)

Index Search

Your unit automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction.

NOTE:

Before starting, make sure the unit is in the Stop mode.

Activate Index Search.

INDEX

Press “INDEX 1” is displayed on the TV screen and search begins in the corresponding direction.

●

To access index codes 2 through 9, press

INDEX

displayed.

Example:

To locate the beginning of B from the current position, press

INDEX

To locate the beginning of D from the current position, press

INDEX

(2) or

(6) repeatedly until the correct index number is

(2) twice.

(6) once.

INDEX

(6). “INDEX –1” or

Current position

INDEX

(2) or

Skip Search

During playback, press over unwanted sections. Each press initiates a 30-second period of fast-motion playback. Normal playback resumes automatically.

To resume normal playback during a Skip Search,

PLAY

press

(4).

SKIP SEARCH

1 to 6 times to skip

Index number

●

When the specified index code is located, playback begins automatically.

Instant ReView

Simply by pressing a single button, the unit power comes on, rewinds, and begins playback of the last timer-recorded program. If you have several programs recorded, you can easily access any of them.

NOTE:

Before starting, make sure that the unit is off and that the Timer mode is disengaged.

Activate Instant ReView.

Press . The unit power comes on and the unit searches for the index code indicating the start of the last timer-recorded program. Once it’s found, playback begins automatically.

●

To watch the first of the 3 programs, press three times. The unit searches and begins playback automatically. You can access a program as far as 9 index codes away from the current tape position.

Page 30 4 August 2003 6:42 pm

Page 31

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 31 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Next Function Memory

The Next Function Memory “tells” the unit what to do after rewinding. Before continuing, make sure the unit is in the Stop mode.

For Automatic Start Of Playback

REW

Press 2 seconds.

For Automatic Power Off Press 2 seconds.

For Automatic Timer Standby Press

For Automatic Cassette Ejection After Tape Rewind Press 2 seconds.

(3), then press

REW

(3), then press

REW

(3), then press

REW

(3), then press

PLAY

(4) within

POWER

TIMER

EJECT

(1) within

within 2 seconds.

(x) within

Repeat Playback

Your unit can automatically play back the whole tape 100 times repeatedly.

Start playback.

PLAY

Press

●

The Play indicator ($) on the front display panel blinks slowly.

●

After playing back a tape 100 times, the unit stops automatically.

Press

●

Pressing stops Repeat Playback.

(4).

Activate Repeat Playback.

PLAY

(4) and hold for over 5 seconds, then release.

Stop Repeat Playback.

STOP

(8) at any time.

PLAY

(4),

REW

(3), FF (5) or

PAUSE

(9) also

Page 31 4 August 2003 6:42 pm

Page 32

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 32 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

OPERATIONS ON VCR DECK (cont.)

Manual Tracking

Your unit is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the CH buttons.

Override automatic tracking.

During playback, press SP/EP on the Remote.

Adjust the tracking manually.

CH +

Press

●

Press SP/EP again to return to automatic tracking.

NOTE:

When a new tape is inserted, the unit enters the automatic tracking mode automatically.

or – on the Remote.

Soundtrack Selection

Your unit is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select.

During Playback

Pressing

●

NOTES:

●

A.MONITOR

You can also select the soundtrack on the Function Set screen.

墌

(

pg. 77)

TRACK

On-Screen Display

H I-F I Hi-Fi sound is played back

H I-F I L

H I-F I R

NORM

H I-F I

“HIFI” should normally be selected. In this mode, Hi-Fi stereo tapes are played back in stereo, and the normal audio track is played back automatically for tapes with only normal audio. “SUPERIMPOSE” must be set to “ON” or the on-screen displays will not appear. (

changes the soundtrack as follows:

USE

Sound on the left Hi-Fi channel is played back

Sound on the right Hi-Fi channel is played back

Sound on the normal track is played back

Both sounds on the Hi-Fi track and normal track are mixed and played back

墌

pg. 76)

Page 32 4 August 2003 6:42 pm

Page 33

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 33 Monday, August 4, 2003 7:24 PM

Basic Recording

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Masterpage:Right-No-Heading

Load a cassette.

Insert a cassette with the record safety tab intact.

●

The unit’s power comes on automatically and the counter is reset to 0:00:00.

Select the VCR deck.

On the unit

VCR/DVD

Press lights up.

On the Remote

VCR

Press

Choose a program.

CH +/–

Press you wish to record.

repeatedly so that the VCR indicator

so that the VCR indicator lights up.

number keys

or the

to select the channel

Set the tape speed.

Press SP/EP. The current setting appears on the front display panel or TV screen. Press SP/EP again to change the setting while the tape speed is displayed on the TV screen.

Start recording.

Press and hold Remote, or press

Pause/Resume recording.

PAUSE

Press

●

You can select channel during the Record Pause mode.

Stop recording.

STOP

Press to remove the cassette.

REC

(7) and press

REC

(7) on the unit.

(9). Press

(8). Then press

PLAY

(4) on the

(4) to resume recording.

EJECT

(x) on the VCR deck

Recording Resume Function

If there is a power outage during recording, Instant Timer Recording or timer recording ( recording will resume automatically when power is restored to the unit unless the unit’s memory backup has expired.

Page 33 4 August 2003 6:42 pm

墌

pg. 33, 34, 36), the

Page 34

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 34 Monday, August 4, 2003 7:24 PM

Recording Features

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Masterpage:Left+

OPERATIONS ON VCR DECK (cont.)

Record One Program While Watching Another

If your unit is connected to the TV via the AV connection,

TV/VCR

press broadcast being recorded disappear. Once recording is in progress, all you need to do is to set the channel controls on the TV for the station you wish to view.

●

The program selected with the TV’s channel controls appears on the TV screen, while the one selected with the unit’s CH buttons is recorded on the tape.

NOTE:

You can also use the DVD deck in the following cases. Before use, be sure to turn on the unit and select the DVD deck.

●

During recording

●

During timer recording

●

During timer standby mode

. The unit’s VCR indicator and the TV

Accidental erasure prevention

To prevent accidental recording on a recorded cassette, remove its safety tab. To record on it later, cover the hole with adhesive tape.

Record safety tab

Instant Timer Recording (ITR)

This easy method lets you record for from 30 minutes to 6 hours (selectable in 30-min. increments), and shuts the unit off after recording is finished.

Start recording.

REC

Press

Press the front display panel.

If you want to record for more than 30 minutes, press

REC

time by 30 minutes.

NOTES:

●

You can only perform ITR using the unit’s front panel.

●

Still picture playback stops automatically after 5 minutes to protect the heads.

●

When the end of the tape is reached during timer recording, the unit stops and “ panel.

●

When the end of the tape is reached during timer recording or Instant Timer Recording, the unit is turned off and “ “$” blink on the front display panel.

●

During Instant Timer Recording, any other timer programed recording won’t start even if their start time has come. In such a case, the timer programed recording starts (if the end time of the timer programed recording is set after the end of Instant Timer Recording) after the Instant Timer Recording finishes.

(7) on the unit.

Engage the ITR mode.

REC

(7) again. “䡬” blinks and “0:30” appears on

Set the recording duration.

(7) to extend the time. Each press extends recording

REC

(7) button on the

䡬

” and “$” blink on the front display

䡬

” and

Page 34 4 August 2003 6:42 pm

Page 35

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 35 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Elapsed Recording Time Indication

Set the counter display.

DISPLAY

Press front display panel.

Reset the counter.

C.RESET

Press

●

The counter is reset to “0:00:00” and shows the exact elapsed time as the tape runs. You can check the exact time of a recording or playback.

until a counter reading appears on the

before starting recording or playback.

Tape Remaining Time

DISPLAY

Press appears.

●

The front display panel shows the tape remaining time with “z” displayed.

until the time remaining on the tape

●

By pressing the show the clock time, counter reading or tape remaining time.

DISPLAY

button, you can change display to

NOTES:

●

When you press the TV screen for 5 seconds, then the displays other than the counter disappears. To clear the counter display, press

DISPLAY

●

Depending on the type of tape being used, the tape remaining time reading may not appear right away, or is not correct. “– –:– –” may sometimes appear, or the display may blink on occasion.

DISPLAY

, the on-screen display appears on

Second Audio Recording

This unit’s built-in MTS decoder enables reception of Multichannel TV Sound broadcast. To record a SAP program received, set “2ND AUDIO RECORD” to “ON”. (

NOTE:

When the channel is changed on the unit;

●

The “STEREO” indicator appears on the screen for about 5 seconds if the program is a stereo broadcast.

●

The “SAP” indicator appears on the screen for about 5 seconds if the program is a SAP broadcast.

●

Both indicators appear when a stereo program is accompanied by SAP sound.

墌

pg. 77)

Page 35 4 August 2003 6:42 pm

Page 36

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 36 Monday, August 4, 2003 7:24 PM

Express Timer Programing

Before performing Express Timer Programing:

●

Make sure that the unit’s built-in clock is set properly.

●

Insert a cassette with the safety tab in place. The unit will come on automatically.

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Masterpage:Left+

OPERATIONS ON VCR DECK (cont.)

Example: To timer-record the program from 8:00 to 10:00 on 24th December, on channel 12.

Select the VCR deck.

On the unit

VCR/DVD

Press lights up.

On the Remote

VCR

Press

Access the Program screen.

PROG.

Press starting out, “P1” appears.)

repeatedly so that the VCR indicator

so that the VCR indicator lights up.

. (If you’re just

Enter the program start time.

START +/–

Press time you want recording to start.

●

Press and hold move in 30-minute increments, or press and release repeatedly to move 1 minute at a time.

Enter the program stop time.

STOP +/–

Press stop.

●

Press and hold press and release repeatedly to move 1 minute at a time.

Enter the program date.

DATE +/–

Press

●

The current date appears on the TV screen. The date you enter appears in its place.

to enter the

START +/–

to enter the time you want recording to

STOP +/–

to move in 30-minute increments, or

Page 36 4 August 2003 6:42 pm

Page 37

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 37 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Enter the channel position.

CH +/–

Press

Press SP/EP.

Press on the TV screen for about 5 seconds, then the normal screen appears. If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears on the TV screen, see page 40.

●

Repeat steps B–H for each additional program.

Press appears on the front display panel.

●

To disengage the timer mode, press

To Timer-Record Weekly Or Daily Serials:

— anytime during stepsC through G, press

key “9”

serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the button again makes the corresponding indication disappear.

Set the tape speed.

Return to the normal screen.

PROG.

or OK. “PROGRAM COMPLETED” appears

Engage the unit’s timer mode.

TIMER

. The unit turns off automatically and “#”

TIMER

again.

) for weekly serials or

DAI LY (number key “8”

WEEKLY (number

) for daily

NOTES:

●

You can program this unit to timer-record as many as 8 programs. If you try to program the unit to record a ninth, “PROGRAM FULL” appears on the TV screen. To record the extra program, you must first cancel any unnecessary programs. (

●

In case of a power failure after programing, the unit’s memory backup keeps your selections for approximately 3 minutes.

●

Programs that start after midnight must have the next day’s date.

Cable Box or DBS Receiver Users

To timer-record a satellite broadcast using Express Timer Programing:

墌

pg. 39)

Perform steps A–I. Enter “L-1” for the channel position in stepF. Set the DBS receiver to the appropriate channel before the selected program begins. Leave the DBS receiver’s power on.

Page 37 4 August 2003 6:42 pm

Page 38

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 38 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

OPERATIONS ON VCR DECK (cont.)

Check, cancel and change programs

Disengage the timer mode.

TIMER

Press

Press to check more information. Each time you press

PROG. CHECK

program’s information appears.

, then press

Access the Program Check screen.

PROG. CHECK

Access the Program screen.

PROG. CHECK

, the next

POWER

again

(1).

Page 38 4 August 2003 6:42 pm

Page 39

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 39 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

To cancel or change a program

Cancel or change a program.

CANCEL

Press settings, press the appropriate button:

STOP +/–, DATE +/–, CH +/–, DAI LY (number key “8” WEEKLY (number key “9”

PROG. CHECK

Press are still some programs remaining, go on to stepF.

TIMER

Press

to cancel a program. To change program

START +/–

) and/or SP/EP.

Return to the normal screen.

as many times as necessary. If there

Return to the timer mode.

Page 39 4 August 2003 6:42 pm

Page 40

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 40 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

OPERATIONS ON VCR DECK (cont.)

When programs overlap each other

If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking.

Example: Program 1 (you have just made) and Program 4 overlap each other.

Confirm the overlapping programs.

Overlapping programs blink on the TV screen.

TTENTION

If there is a conflict in the timer schedule and one program overlaps with another, only the parts shown below in gray will be recorded.

Pattern 1:

Program 1

Program 2

Pattern 2:

Program 1

Pattern 3:

The program with the lower program number will be recorded.

CH10

CH40

The program starting earlier will be recorded.

CH10

Program 2

The program starting earlier will be recorded, followed by the remaining portion of the other program.

CH40

Not recorded

Select the program to modify.

Press rt, then press OK or e.

●

You can only select one of the overlapping programs.

NOTE:

If you do not mind this overlap, press program setting. The program with the lower program number will be recorded and the other one will not be recorded correctly. If no changes are made for approximately 1 minute, the unit will return to the normal screen.

Cancel or change program setting.

To cancel a program,

screen you do not want is shown. “PROGRAM COMPLETED” appears on the TV screen for about 5 seconds, then the normal screen appears.

To change a program, START +/–, STOP +/–, DATE +/–, CH +/–, DAILY

number key “8”

(

when the Program screen on which you want to make changes is shown, then press OK. “PROGRAM COMPLETED” appears on the TV screen for about 5 seconds, then the normal screen appears.

press

press the appropriate button:

WEEKLY (number key “9”

PROG.

CANCEL

to finish the timer

when the Program

) and/or SP/

NOTE:

If the overlap is not yet solved, or another overlap occurs with the timer program setting after making the last correction on a program, the conflicting programs will be shown on the Program Check screen again. Repeat the above steps again until the overlap is solved.

Program 1

Page 40 4 August 2003 6:42 pm

CH10

Program 2

CH40

Not recorded

Page 41

Filename [XVC33UM_07S-VHS.fm]

XVC33UM_01.book Page 41 Monday, August 4, 2003 7:24 PM

Satellite Auto Recording

This function allows you to automatically record a satellite program which is timer-programed on your external DBS receiver. Connect a DBS receiver to the unit’s AUDIO/VIDEO INPUT (L-1) connectors and program the timer on the DBS receiver. The unit starts or stops recording by the signals input from the DBS receiver. After recording, the unit’s power shuts off automatically.

●

You can also connect the cable box if it has a timer.

“N” indicator

Masterpage:Right-No-Heading

ATTENTION

●

Be sure not to turn on the DBS receiver before the program is executed; otherwise, the unit will start recording when the DBS receiver’s power is turned on.

●

If you have connected another appliance other than a DBS receiver to the AUDIO/VIDEO INPUT (L-1) connectors, be sure not to engage the Satellite Auto Recording mode; otherwise, the unit will start recording when the connected appliance’s power is turned on.

●

Satellite Auto Recording and timer-recording cannot be done at the same time.

Before performing the following steps:

●

Make sure the DBS receiver is connected to the unit’s AUDIO/VIDEO INPUT (L-1) connectors.

●

Program the timer on the DBS receiver.

●

Insert a cassette with the safety tab in place.

●

Slide the

On the unit

Press lights up.

On the Remote

Press

TV/VCR/DVD

switch to the right.

Select the VCR deck.

VCR/DVD

VCR

repeatedly so that the VCR indicator

so that the VCR indicator lights up.

Set the tape speed.

Press SP/EP.

Engage the Satellite Auto Recording mode.

Press and hold and “#” indicators light up and the unit turns off automatically.

REC LINK

for about 2 seconds. The “N”

NOTES:

●

To disengage the Satellite Auto Recording mode, press

●

If the unit’s power is off, it is not possible to engage the Satellite Auto Recording mode.

●

In stepC, if the “N” indicator does not light but instead blinks quickly even though your DBS receiver’s power is off, Satellite Auto Recording will not work properly with that DBS receiver*. If this is the case, perform “Express Timer Programing” ( timer-record a satellite program.

* Some DBS receivers output signals even if the power is off. Satellite Auto Recording is not possible with those DBS receivers.

●

The “N” indicator blinks while Satellite Auto Recording is in progress.

●

For timer programing of the DBS receiver, refer to the instruction manual of the DBS receiver.

●

Satellite Auto Recording is not possible if your DBS receiver does not have a timer.

●

Pressing the unit’s Satellite Auto Recording mode.

●

If there are more than one satellite programs you wish to record with Satellite Auto Recording, it is not possible to set different tape speeds for each program.

●

Depending on the type of DBS receiver, the unit may not record a slight portion of the beginning of the program or may record slightly longer than the actual length of the program.

●

If you engage the Satellite Auto Recording mode when the DBS receiver’s power is on, the unit will not start Satellite Auto Recording even though the “N” and “#” indicators blink. When the DBS receiver shuts off once and is turned back on again, the unit starts recording.

●

You can also record a program from your cable system in the same way if the system has a timer.

POWER

(1) button while Satellite Auto Recording is in progress turns off the unit’s power and disengages the

REC LINK

. The “N” indicator goes off.

墌

pg. 36) to

Page 41 4 August 2003 6:42 pm

Page 42

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 42 Monday, August 4, 2003 7:24 PM

Masterpage:Left

OPERATIONS ON DVD DECK

To play back a MP3/JPEG disc, see pages 62 – 67.

Basic Playback

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Load the disc.

●

On the unit

Press lights up.

On the Remote

Press

Example: DVD VIDEO

OPEN/CLOSE

Press disc tray.

The unit’s power comes on automatically.

Place the disc in the disc tray.

For details, refer to “Placing a Disc” (

OPEN/CLOSE

Press disc tray.

PLAY

Pressing Playback begins automatically if the auto-playback DVD disc is loaded. Although the VCR deck is selected, the DVD deck is selected automatically if the VCR deck is in stop mode.

(4) also close the disc tray.

(x) on the DVD deck to open the

墌

(x) on the DVD deck to close the

pg. 7).

Select the DVD deck.

VCR/DVD

DVD

repeatedly so that the DVD indicator

so that the DVD indicator lights up.

Start playback.

PLAY

(4).

ATTENTION

●

You can not use the DVD deck when the VCR deck is in the Satellite Auto Recording standby and recording mode.

●

You can use the DVD deck when the VCR deck is in the timer standby mode.

Title number Chapter

●

It may take a few seconds to start playback.

●

If you load a DVD disc whose region code does not match the DVD deck, “REGION CODE ERROR!” appears on the TV screen. For details, refer to “Region Number” (

●

With Video CD discs with PBC control or some DVD discs, the menu display may appear on the TV screen after starting playback. In this case, select an item which you want to play back from the menu. Otherwise, the playback cannot go forward. Refer to “Locating a desired scene using the menu of the Video CD with PBC” ( scene using the DVD menu” (

Pause playback.

PAUSE

Press

●

To resume normal playback, press

Press deck to open the disc tray, then remove the disc.

●

Pressing you stop playback. For details, see “Resume Function” on page 45.

(9).

Stop playback.

STOP

(8). Press

PLAY

number

墌

pg. 43) or “Locating a desired

墌

OPEN/CLOSE

(4) resume playback from the position where

Elapsed time

pg. 43).

PLAY

(4).

(x) on the DVD

墌

pg. 5).

NOTE:

When you press the unit’s power comes on and the disc tray opens automatically.

OPEN/CLOSE

(x) while the unit is turned off,

Page 42 4 August 2003 6:47 pm

Page 43

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 43 Monday, August 4, 2003 7:24 PM

Playback Features

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

Playback Control (PBC) Function — Locating a desired scene using the

menu of the Video CD with PBC

Some Video CD discs supports the PBC function. PBC is an abbreviation of “PlayBack Control.” A Video CD disc recorded with PBC has its own menus, such as a list of the songs of the disc. You can locate a specific scene by using the menu.

TV/VCR/DVD

switch to the right.

Masterpage:Right-No-Heading

Locating a desired scene using the DVD menu

DVD VIDEO discs may have two types of the menus; top menu and disc menu.

Top menu

DVD discs generally have their own menus which show the disc contents. These menus contain various items such as titles of a movie, names of songs, or artist information. You can locate a desired scene by using the top menu displayed on the TV screen.

TOP MENU

Press

Disc menu

DVD discs have the disc menu to select subtitle and audio language etc. for each title.

Press

Access the DVD menu.

TOP MENU

Press

to access the top menu.

to access the disc menu.

Access the PBC menu.

In stop mode

PLAY

Press

●

Depending on a disc, PBC menu may automatically appear on the TV screen by simply loading a disc on the unit.

During playback

Press

●

“PBC” appears on the front display panel.

Press the appropriate

●

The unit starts playback of the selected item.

●

When “NEXT” or “PREVIOUS” appears on the TV screen: Pressing Pressing

●

You can return to the menu by pressing

●

The method of the operation is different depending on the disc.

(4).

RETURN

Start playback.

SKIP

(6) advances to the next page.

SKIP

(2) returns to the previous page.

number keys

RETURN

NOTES:

●

If you want to playback a PBC-compatible Video CD disc without activating the PBC function, start playback by using

number keys

the

●

To activate the PBC function when a PBC-compatible Video CD disc is being played back without the PBC function, press

TOP MENU

“RESUME” is set to “ON”) then press

instead of the

, or press

PLAY

(4) button.

STOP

(8) (press twice when

PLAY

(4).

Example:

Start playback.

rt w e

Press

●

It may be possible to select the desired item using the

keys

depending on the disc.

to select a desired item, then press OK.

number

NOTES:

●

When “X” appears on the TV screen in step1, the disc does not have a top menu or disc menu.

●

Top menu or disc menu may not appear depending on the discs even if it is recorded in DVD VIDEO format and finalized. In that case, press number of titles on a disc, then press the appropriate

keys

to select the desired title.

STOP

(8) to display the total

number

Page 43 4 August 2003 6:47 pm

Page 44

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 44 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

OPERATIONS ON DVD DECK (cont.)

Locating the start point of the item or skip the item

SKIP

Press

Example:

To locate the beginning of item B from the current position, press

SKIP

To locate the beginning of item D from the current position, press

●

When the specified item is located, playback begins automatically.

(2) or

(2) twice.

SKIP

(6) once.

SKIP

(6) during playback.

Current position

The number you press the button

High-Speed Search

During playback, press FF (5) for forward high-speed search, or

●

The more times you press, the faster the playback picture moves.

●

To resume normal playback, press

During playback, press and hold high-speed search, or press and hold reverse high-speed search.

●

While you press and hold the button, the image is played back at 5x speed.

●

To resume normal playback, release

REW

(3) for reverse high-speed search.

PLAY

(4).

SKIP

(6) for forward

SKIP

(2) or

(2) for

SKIP

(6).

NOTES:

●

Actual speed may be different from that displayed on the TV screen depending on the discs.

●

Playback sound is not heard in any High-Speed search mode other than in 1.5x speed search mode.

●

During 1.5x speed search of a DVD VIDEO disc, you can hear the played back audio converted into Linear PCM format in stereo. In such a case, the pitch and sound quality may change depending on the disc.

●

In case of DVD VIDEO discs formatted in DTS format, SVCD or Audio CD discs, playback sound is not heard during 1.5x speed search.

●

When switching to 1.5x speed search during high-speed Search, first press press FF (5).

Page 44 4 August 2003 6:47 pm

PLAY

(4) to return to normal playback, then

Page 45

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 45 Monday, August 4, 2003 7:24 PM

Still Picture/Frame-By-Frame Playback

Pause during playback.

PAUSE

Press

Activate frame-by-frame playback.

Press

●

To resume normal playback, press

(9).

PAUSE

(9) to advance a still picture.

PLAY

(4).

Slow Motion

During playback, press

PAUSE

(9), then press for reverse slow motion playback, or FF (5) for forward slow motion playback.

●

Each press of FF (5) changes the playback speed as follows: 1/32]1/16]1/4]1/2

●

Each press of follows (only for DVD VIDEO discs): –1/32]–1/16]–1/4]–1/2

●

To resume normal playback, press

REW

(3) changes the playback speed as

PLAY

(4).

NOTES:

●

Reverse slow motion playback is possible only with the DVD VIDEO discs.

●

This function may not works for some Video CD or SVCD.

REW

Resume Function

It is possible to memorize the position where you stop playback and resume playback from that position.

●

Be sure to set “RESUME” to “ON” or “DISC RESUME”.

墌

(

pg. 81)

(3)

Masterpage:Right-No-Heading

Resume playback.

PLAY

Press

(4). The unit start playback from the resume

point.

●

“RESUME PLAY” appears on the front display panel.

NOTES:

●

Resume Function does not work on the Audio CD. It also may not work depending on the discs.

●

If you stop the playback of a disc for which an resume point has already been memorized, the memory will be updated with the new resume point.

●

After the unit has memorized the resume point for 30 discs, remembering a new resume point will cause the unit to delete the oldest memorized point. Stopping playback of a disc for which a resume point is already stored may change the order in which the points are stored. This may potentially change the order in which points are deleted.

●

When the unit memorizes a resume point for a disc, it also remembers audio language, subtitle and angle settings.

●

This function may not works for some Video CD or SVCD.

Zooming

ZOOM

Press

●

Each press of

1.8x]4x]8x]16x]32x]64x

●

When a 16:9 aspect picture source is displayed on a 4:3 aspect TV (conventional TV) in Letter Box conversion mode, the margins in black shown on top and bottom of the TV screen will be cropped by selecting 1.8x imagination. In such a case, note that both left and right side parts of the picture will also be cropped.

●

While zoomed, the picture may look coarse or distorted.

during playback or while paused.

ZOOM

changes the magnification as follows:

Current magnification

Memorize the resume point.

STOP

Press

●

“RESUME STOP” appears on the front display panel.

●

The unit enters Resume Stop mode and memorise the position where you stop playback as the resume point.

●

The unit retains a memory of the resume points of the last 30 discs played back, even though they have been ejected if “RESUME” is set to “DISC RESUME”. (

●

To clear the resume point:

When “RESUME” is set to “ON”:

•Press

• Eject the disc.

When “RESUME” is set to “DISC RESUME”:

• Set “RESUME” to “OFF”. (

•Press

Page 45 4 August 2003 6:47 pm

(8) during playback.

STOP

(8) in stop mode.

POWER

(1) to turn off the unit.

STOP

(8) in stop mode.

墌

pg. 81)

墌

pg. 81)

Zoomed-in area

rt w e

Press

●

To resume normal playback, press OK.

to move the zoomed-in scene.

Page 46

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 46 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

OPERATIONS ON DVD DECK (cont.)

●

Each time you press we, the setting changes as follows:

NONE]ACTION]DRAMA]THEATER](Back to the beginning)

NONE

: No effect

ACTION

: Suitable for action movies and sports

programs in which sounds dynamically

DRAMA

THEATER

●

The selection menu disappears automatically if you do not change the selection for 10 seconds.

Select the effect level.

Press rt to select the desired effect level. (level 1 to 5)

●

To resume normal playback, press

move.

: Provides the natural and warm sound. You

can enjoy movies in a relaxed mood.

: You can enjoy sound effects like in a major

theater.

3D-PHONIC

NOTES:

●

The 3D Phonic function works correctly only when playing back a DVD VIDEO disc recorded in the Dolby Digital format. With other sources, you cannot get any effect if you activate 3D Phonic function.

●

When playing back a DVD VIDEO disc recorded with the Dolby Digital that does not contain the rear signal, you cannot get a correct 3D Phonic sound even if you activate 3D Phonic function.

●

The 3D Phonic function does not affect the Dolby Digital bitstream signal from the DIGITAL AUDIO OUT connector.

●

When 3D Phonic function is activated, Analog Down Mix and D. Range Control functions are disabled. (

墌

pg. 80)

3D Phonic

3D Phonic function allows you to get a simulated surround effect from your stereo system. You can enjoy the vertical surround sound with your 2-channel stereo system.

Access the selection menu.

3D-PHONIC

Press

●

The current setting appears on the right bottom corner of the TV screen.

Select the mode.

Press we repeatedly, then press OK.

during playback.

Selected mode Effect level

Page 46 4 August 2003 6:47 pm

Page 47

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 47 Monday, August 4, 2003 7:24 PM

VFP function — Adjusting the picture quality

Masterpage:Right-No-Heading

Select the parameter.

Press rt repeatedly to select a parameter you want to adjust, then press OK.

●

Adjust gradually and confirm picture appearance results are as preferred.

The VFP (Video Fine Processor) function enables you to adjust the picture character according to the type of programing, picture tone or personal preference.

NOTE:

Before you start operation; The VFP setting screen disappears if no operations are done for more than about 10 seconds. If the setting screen disappears before you finish, start from step 1 again.

Access the VFP setting menu.

DVD PICTUR E

Press playback.

●

The current setting appears on the TV screen.

Select the VFP mode.

Press we repeatedly.

●

Each time you press we, the VFP mode changes as follows:

NORMAL]CINEMA]USER 1]USER 2](Back to the beginning)

NORMAL

CINEMA

USER 1 USER 2

: Select this normally.

: Suitable for movie.

/ :

during

NORMAL

GAMMA

BRIGHTNESS

CONTRAST

SATURATION

TINT

SHARPNESS

Y DELAY

You can adjust parameters that affect picture appearance and store settings. Go to step 3.

GAMMA

(–4 to +4):

Controls brightness of neutral tints while maintaining brightness of dark and bright portions.

BRIGHTNESS

Controls screen brightness.

(–16 to +16):

CONTRAST

Controls screen contrast.

(–16 to +16):

SATURATION

Controls screen color depth.

(–16 to +16):

TINT

Controls screen tint.

(–16 to +16):

SHARPNESS

Controls screen sharpness.

(+0 to +3):

Y DELAY

Controls screen color gap.

(–2 to +2):

●

VFP menu disappears and the following pop-up window appears on the TV screen.

GAMMA

Adjust the parameter.

GAMMA

Press rt repeatedly to change the setting, then press

●

The current VFP settings appear again.

NOTE:

You cannot adjust the parameters of “NORMAL” and “CINEMA”.

To adjust picture appearance manually

Access USER menu.

Press we repeatedly to select “USER 1” or “USER 2”.

USER 1

GAMMA

BRIGHTNESS

CONTRAST

SATURATION

TINT

SHARPNESS

Y DELAY

Adjust the other parameters.

Repeat steps 4 and 5 to adjust other parameters.

To return to the normal screen

DVD PICTU RE

Press

To activate your setting

DVD PICTU RE

Press

, then press we repeatedly to select “USER 1” or “USER 2” that you have changed the parameters.

Page 47 4 August 2003 6:47 pm

Page 48

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 48 Monday, August 4, 2003 7:24 PM

Using the on-

Masterpage:Left+

OPERATIONS ON DVD DECK (cont.)

How to Access the on-screen bar

PLAY SETUP

Press

twice whenever a disc is loaded.

screen bar

You can check disc information while the disc is loaded and you can use some functions using the on-screen bar. The on-screen bar allows you the various playback operations.

Example: During DVD VIDEO playback

Example: During Video CD playback

Contents of the on-screen bar during playback

DVD

Video CD

Disc type

Current transfer rate (Megabits per second)

Current title (for DVD)

Current chapter number (for DVD) or track number (for other type of discs)

Time information (

Playback status

: appears during playback. / : appears during fast forward/reverse. / : appears during playback in forward slow-

motion/reverse slow-motion.

: appears when paused. : appears when stopped.

Select this to change time information. (See 5 in the illustration above) (

Select this for Repeat Playback. (

Select this for time search function. (墌pg. 51)

Select this for chapter search function. (墌pg. 52)

Select this to change audio language or channel.

墌

(

pg. 56, 57)

Select this to change subtitle language. (

Select this to change view angle. (

Select this for Program Playback. (

Select this for Random Playback. (

墌

pg. 49)

墌

墌墌墌

pg. 50)

墌

pg. 55) pg. 53) pg. 53)

pg. 54)

Page 48 4 August 2003 6:47 pm

Page 49

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 49 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Basic operation on the on-screen bar

Example: When selecting the Repeat mode of DVD

During playback or while stopped

Access the on-screen bar.

PLAY SETUP

Press the TV screen.

●

The currently selected item is highlighted.

Select menu item.

Press we to move 0 to , then press OK. The pop-up window appears under the selected item.

●

The current setting appears.

Select the option.

Press rt to select the desired option, then press OK.

●

Each time you press rt, the options change.

To clear the on-screen bar

PLAY SETUP

Press

NOTE:

See the corresponding pages for details on each function.

twice. The on-screen bar appears on

Change the time information

You can change the time information in the on-screen bar on the TV screen and the front display panel of the unit.

During playback or while stopped

Access the on-screen bar.

PLAY SETUP

Press the TV screen.

Select menu item.

Press we to move 0 to , then press OK.

●

Each time you press OK, the time information changes as follows;

Example: During DVD playback

TIME

: Elapsed playing time of current chapter/track

REM

: Remaining time of current chapter/track

TOTAL

: Elapsed time of title/disc

T. R E M

: Remaining time of title/disc

To clear the on-screen bar

PLAY SETUP

Press

NOTES:

●

While playing a Video CD, Audio CD or SVCD, the hour digit indication does not appear.

●

While a DVD is stopped, “– – : – –” appears in the time information display.

twice. The on-screen bar appears on

(Back to the beginning)

Page 49 4 August 2003 6:47 pm

Page 50

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 50 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

OPERATIONS ON DVD DECK (cont.)

Select the repeat mode.

Press rt repeatedly to select the Repeat mode, then press OK.

●

The mode changes as follows:

DVD VIDEO

CHAPTER]TITLE]A-B]OFF](Back to the beginning)

Repeat Playback

CHAPTER

TITLE

A-B

OFF:

Video CD/SVCD/CD

TRACK]ALL]A-B]OFF](Back to the beginning)

TRACK

ALL

A-B

OFF:

●

“A-B” cannot be selected while stopped.

To clear the on-screen bar

Press

To cancel Repeat Playback

Repeat from step A, select “OFF” in step C, then press

When using the REPEAT button:

: The current chapter is played back

: The current title is played back

PLAY SETUP

repeatedly.

repeatedly. The desired part is played back

repeatedly. ( Each title and chapter is played

back once.

The current track is played back repeatedly.

All tracks are played back repeatedly.

The desired part is played back repeatedly. (

Each track is played back once.

墌

pg. 51)

Access the repeat mode.

REPEAT

You can repeat playback as you like according to the type of disc. DVD VIDEO: during playback Audio CD: during playback or in stop mode Video CD/SVCD: in stop mode or during playback with PBC

When using the on-screen bar

Access the on-screen bar.

PLAY SETUP

Press the TV screen.

Select menu item.

Press we to move 0 to , then press OK.

●

The following pop-up window appears under the selected item.

Page 50 4 August 2003 6:47 pm

disactivated

twice. The on-screen bar appears on

Press repeat.

●

Repeat mode is displayed on the TV.

Press mode, then press OK.

●

To stop Repeat Playback, press

●

To cancel Repeat Playback, press “OFF” appears on the TV screen, then press OK.

NOTES:

●

Repeat Playback is not possible with a Video CD and SVCD with PBC function.

●

Repeat Playback may not work properly depending on the type of disc being used.

●

You cannot select A-B Repeat Playback by pressing

during playback of the item you want to

Select the repeat mode.

REPEAT

repeatedly to select the desired repeat

STOP

(8).

REPEAT

repeatedly until

REPEAT

Page 51

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 51 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

A-B Repeat Playback

You can repeat the desired part.

Access the on-screen bar.

PLAY SETUP

Press the TV screen.

Select menu item.

Press we to move 0 to , then press OK.

●

The following pop-up window appears under the selected item.

Select the repeat mode.

Press rt repeatedly to select “A-B”.

Select the start point.

Press OK at the beginning of the part you want to repeat (point A).

●

The following display appears in the on-screen bar.

Select the end point.

Press OK at the end of the part you want to repeat (point B).

●

A-B Repeat Playback starts. The selected part of the disc (between point A and B) is played repeatedly.

To cancel A-B Repeat Playback

Repeat from step A, select “OFF” in step C, then press

●

You can also cancel Repeat Playback by pressing

SKIP

(6).

To clear the on-screen bar

PLAY SETUP

Press

NOTES:

●

A-B Repeat Playback may not work properly depending on the type of disc being used.

●

The subtitles recorded around A-B point may not appear.

●

The end of the item will be set as “B” point if the end of the item reached before you set the “B” point.

●

When playing back a DVD, A-B Repeat Playback is possible only within the same title.

●

“A-B” cannot be selected during Program and Random Playback.

●

“A-B” cannot be selected while stopped.

twice. The on-screen bar appears on

SKIP

(2)

Time Search

You can play back a disc from the desired point by specifying the elapsed time from the beginning of the current title (for DVD VIDEO) or the disc (for Audio CD/Video CD) using the Time Search. When a PBC-compatible Video CD is played back, be sure to inactivate PBC function before you perform Time search by pressing the you start playback.

Press the TV screen.

Press we to move 0 to , then press OK.

●

The following pop-up window appears under the selected item.

Press the

Example: To play back from a point 2 (hours): 34 (minutes): 08 (seconds) elapsed

If you have specified a wrong selection,

Press w repeatedly until the wrong number is erased, then press

●

The unit starts playback from the specified time.

To clear the on-screen bar

Press

NOTES:

●

When “X” is displayed on the TV screen in stepC, you have selected a point that excesses the recording time of the disc.

●

Some DVD VIDEO discs do not contain time information, and it is no possible to use the Time Search function. In such a case, “X” is displayed on the TV screen as well.

●

Time Search does not work while you play back the Video CD or SVCD with the PBC Function.

Reactivate the Playback Control (PBC) Function

You can reactivate the PBC function when you play back a PBCcompatible Video CD disc without PBC function.

●

Press

number keys

instead of the

Access the on-screen bar.

PLAY SETUP

twice. The on-screen bar appears on

Select menu item.

Select the time.

number keys

TIME _ : _ _ : _ _

TIME _ : _ _ : _ _TIME 2 : 3 _ : _ _

TIME _ : _ _ : _ _TIME 2 : 3 4 : 0 _

number keys

PLAY SETUP

TOP MENU

(0-9) to enter the time, then press

TIME _ : _ _ : _ _TIME 2 : _ _ : _ _

Press 2

TIME _ : _ _ : _ _TIME 2 : 3 4 : _ _

Press 4

TIME _ : _ _ : _ _TIME 2 : 3 4 : 0 8

Press 8

to enter the correct numbers.

during playback.

PLAY

(4) button when

Press 3

Press 0

Page 51 4 August 2003 6:47 pm

Page 52

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 52 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

OPERATIONS ON DVD DECK (cont.)

Chapter Search

You can start playback the desired chapter using the on-screen bar.

Access the on-screen bar.

PLAY SETUP

Press the TV screen.

Select menu item.

Press we to move 0 to , then press OK.

●

The following pop-up window appears under the selected item.

twice. The on-screen bar appears on

Select the chapter.

Press the number, then press OK.

●

If you have specified a wrong selection

Enter the appropriate

To clear the on-screen bar

Press

number keys

The unit starts playback from the selected chapter.

Examples:

To select track 5, press the To select track 15, press the To select track 25, press

●

It is not possible to use the

PLAY SETUP

(0-10) to enter the desired chapter

number key “5”

number key “1”

number key “2”

number keys

number key “+10”

again.

and

“5”

NOTES:

●

When “X” is displayed on the TV screen in stepC, the chapter you have selected is not contained in the disc, or chapter search does not work on the disc.

●

Chapter Search starts automatically when you select the desired chapter in stepC depending on the disc.

Page 52 4 August 2003 6:47 pm

Page 53

Filename [XVC33UM_08DVD.fm]

XVC33UM_08DVD.fm Page 53 Friday, August 29, 2003 5:01 PM

Masterpage:Right-No-Heading

Program Playback

You can play back up to 99 tracks in the desired order.

Access the on-screen bar.

Press

PLAY SETUP

Select the menu item.

Press we to move 0 to , then press OK.

● The program table appears under the on-screen bar.

Select the tracks in the desired order.

Press the appropriate

number keys

tracks.

twice in stop mode.

to select the

Program time

Random Playback

You can play back all the tracks on the disc in random order.

Access the on-screen bar.

Press

PLAY SETUP

Select the menu item.

Press we to move 0 to , then press OK.

● Playback starts in random order.

● To stop and quit Random Playback, press

● To cancel Random playback, repeat step B during Random

Playback. Normal playback resumes at the current point.

To clear the on-screen bar

Press

PLAY SETUP

NOTES:

● The same track will not be played back more than once during

Random Playback.

● Random playback is canceled when all the tracks have been

played back.

twice in stop mode.

STOP

(8).

Examples:

● To select track 5, press the

● To select track 15, press the

● To select track 25, press

“5”

If you have specified a wrong selection

Press

● When all of the programed tracks have been played back, Program Playback stops, but the programed information remains.

● To stop Program Playback, press

● To clear all the programed tracks, press

playback and press then press

● During Program Playback, pressing selection of the program. Pressing beginning of the current selection.

To clear the program table

Press

(8). The last selection programed is erased.

STOP

Start playback.

PLAY (4

PLAY SETUP

). Playback starts in the selected order.

PLAY SETUP

(8) again.

STOP

number key “5”

number key “+10”

STOP

to clear the program table,

SKIP

and

“5”

twice, then

(8).

(8) to stop

STOP

(6) skip to the next

(2) returns to the

NOTE:

Program Playback is not possible depending on the type of disc.

Page 53 29 August 2003 5:01 pm

Page 54

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 54 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

OPERATIONS ON DVD DECK (cont.)

Select the subtitle language.

Press rt repeatedly to select the desired subtitle language, then press OK.

●

Each time you press the button, the subtitle language changes.

To clear the on-screen bar

PLAY SETUP

Press

NOTES:

●

For DVD VIDEO

Some subtitle languages are abbreviated in the pop-up window. See “Language Code List” (

●

For SVCD

SVCD can contain up to four subtitles. Pressing changes the subtitles regardless of whether the subtitles are recorded or not. (Subtitles will not change if no subtitle is recorded.)

●

When “X” appears on the TV screen in stepC, subtitle language is not recorded.

When using the SUB TITLE button:

墌

pg. 23).

SUB TITLE

Subtitle Selection

You can select subtitle language.

●

During playback

When using the on-screen bar

Access the on-screen bar.

PLAY SETUP

Press the TV screen.

twice. The on-screen bar appears on

Access the menu.

SUB TITLE

Press

●

The following pop-up window appears on the TV screen.

Example (DVD):“ENGLISH” is selected out of 3 subtitle

Select the subtitle language.

Press rt or subtitle language, then press OK.

●

Each time you press the button, the subtitle language changes.

●

The pop-up window disappears if no operation is done for about 5 seconds.

languages recorded.

SUB TITLE

repeatedly to select the desired

NOTE:

When “X” appears on the TV screen in stepB, subtitle language is not recorded.

Select menu item.

Press we to move 0 to , then press OK.

●

The following pop-up window appears under the selected item.

Example (DVD):“ENGLISH” is selected out of 3 subtitle

Page 54 4 August 2003 6:47 pm

languages recorded.

Page 55

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 55 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Angle Selection

You can enjoy a variety of scene angles if the DVD VIDEO disc contains “multi-angle” parts, where multiple cameras were used to shoot the same scene from different angles. If the disc contains “multi-angle” parts, “ ” appears on the TV screen at the beginning of the “multi-angle” part when “ON SCREEN GUIDE” is set to “ON”.

●

During playback

When using the on-screen bar

Access the on-screen bar.

PLAY SETUP

Press the TV screen.

Select menu item.

Press we to move 0 to , then press OK.

●

The following pop-up window appears under the selected item.

Example: The first view angle is selected out of 3 view angles

recorded.

twice. The on-screen bar appears on

When using the ANGLE button:

Access the menu.

ANGLE

Press

●

The following pop-up window appears on the TV screen.

Example:The first view angle is selected out of 3 view angles

Press rt or view angle, then press OK.

●

Each time you press the button, the angle of the scene changes.

●

The pop-up window disappears if no operation is done for about 5 seconds.

Example:

1/3]2/3]3/3

recorded.

Select the view angle.

ANGLE

repeatedly to select the desired

](Back to the beginning)

1 1

Select the view angle.

Press rt repeatedly to select the desired view angle, then press OK.

●

Each time you press the button, the angle of the scene changes.

To clear the on-screen bar

PLAY SETUP

Press

NOTE:

When “X” appears on the TV screen in stepC, the current scene is not recorded from multiple angles.

Page 55 4 August 2003 6:47 pm

Page 56

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 56 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

OPERATIONS ON DVD DECK (cont.)

Select menu item.

Press we to move 0 to , then press OK.

●

The following pop-up window appears under the selected item.

Example:“ENGLISH” is selected out of 4 audio languages

Press rt repeatedly to select the desired audio language, then press OK.

●

To clear the on-screen bar

Press

recorded.

Select the audio language.

Each time you press the button, the audio language changes.

PLAY SETUP

Audio Language Selection

Some DVD discs contain the multiple audio. You can select the audio language of movies (DVD VIDEO).

●

During playback

When using the on-screen bar

Access the on-screen bar.

PLAY SETUP

Press the TV screen.

twice. The on-screen bar appears on

NOTES:

●

Some audio languages are abbreviated in the pop-up window. See “Language Code List” (

●

If “X” appears on the TV, the current scene does not contain plural audio languages.

When using the A.MONITOR button:

Access the menu.

A.MONITOR

Press

●

The following pop-up window appears on the TV screen.

Example: “ENGLISH” is selected out of 3 audio languages

Press rt or desired audio language, then press OK.

●

recorded.

Select the audio language.

A.MONITOR

Each time you press the button, the audio language changes. The pop-up window disappears if no operation is done for about 5 seconds.

墌

pg. 23)

repeatedly to select the

NOTE:

Some audio languages are abbreviated in the pop-up window. See “Language Code List” (

墌

pg. 23).

Page 56 4 August 2003 6:47 pm

Page 57

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 57 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Audio Channel Selection

When you play certain karaoke (DVD/Video CD/SVCD), you can enjoy karaoke by selecting the audio channel to play.

●

The sound of each audio channel depends on the contents of the disc.

●

During playback

When using the on-screen bar

Access the on-screen bar.

PLAY SETUP

Press the TV screen.

Select menu item.

Press we to move 0 to , then press OK.

●

The following pop-up window appears under the selected item.

Example: “ST” (stereo) is selected.

Select the audio channel.

Press rt repeatedly to select the desired audio channel, then press OK.

●

Each time you press the button, the audio channel changes.

To clear the on-screen bar

PLAY SETUP

Press

twice. The on-screen bar appears on

When using the A.MONITOR button:

Access the menu.

A.MONITOR

Press

●

The following pop-up window appears on the TV screen.

Example:“ST” (stereo) is selected out of 3 audio channels

Press rt or desired audio channel, then press OK.

●

For Video CD

ST]L]R](Back to the beginning)

For SVCD

ST 1]ST 2]L 1]R 1]L 2]R 2](Back to the beginning)

recorded.

Select the audio channel.

Each time you press the button, the audio channel changes. The pop-up window disappears if no operation is done for about 5 seconds.

To listen to normal stereo playback.

To listen to L (left) audio channel only.

To listen to R (right) audio channel only.

ST 1/ST 2

L 1/L 2

R 1/R 2:

A.MONITOR

To listen to normal stereo playback of ST 1 or ST 2 channel.

To listen to the L (left) 1 or 2 audio channel.

To listen to the R (right) 1 or 2 audio channel.

repeatedly to select the

Page 57 4 August 2003 6:47 pm

Page 58

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 58 Monday, August 4, 2003 7:24 PM

Parental Lock

This function restricts playback of DVD VIDEO discs which contain violent (and other) scenes according to the level set by the user. For example, if a movie which includes violent scenes supports the parental lock feature, such scenes which you do not want to let children view can be cut or replaced with other scenes.

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

OPERATIONS ON DVD DECK (cont.)

Access the DVD Set Up menu.

A B

Press rt repeatedly to move 0 to “PARENTAL LOCK“, then press OK.

●

Press rt repeatedly to move 0 to “COUNTRY CODE“, then press OK.

SET UP MENU

Press

Press we to select “ OTHERS”.

Access the “PARENTAL LOCK“ menu.

The “PARENTAL LOCK“ submenu appears on the TV screen. It is possible to access the “PARENTAL LOCK“ menu only in the stop mode when a DVD disc is loaded on the unit.

Access the country code menu.

PARENTAL LOCK

COUNTRY CODE

SET LEVEL

PASSWORD

EXIT

Masterpage:Left+

NONE

_ _ _ _

To set Parental Lock for the first time

Turn on the unit.

POWER

Press

(1).

Select the country code.

Press rt repeatedly to move 0 to select the country code, then press OK.

●

See “Country/Area Code List for Parental Lock” (

●

The 0 moves to “SET LEVEL”.

Select the Level.

墌

pg. 60).

Press OK, then press rt repeatedly to move 0 to select the level of restriction, then press OK.

●

The 0 moves to “PASSWORD”.

●

The smaller the value of level is, the more restrictive the Parental Lock level is.

●

Select “NONE” to cancel this function.

SELECT

USE TO SELECT. USE OK TO CONFIRM. TO EXIT, PRESS [SET UP MENU].

PARENTAL LOCK

COUNTRY CODE

SET LEVEL

PASSWORD

EXIT

SELECT

USE TO SELECT. USE OK TO CONFIRM. TO EXIT, PRESS [SET UP MENU].

PARENTAL LOCK

COUNTRY CODE

SET LEVEL

PASSWORD

EXIT

SELECT

USE TO SELECT. USE OK TO CONFIRM. TO EXIT, PRESS [SET UP MENU].

NONE

_ _ _ _

NONE

_ _ _ _

UG UM US UY UZ VA VC

NONE 8 7 6 5 4 3

Select the DVD deck.

On the unit

VCR/DVD

Press

repeatedly so that the DVD indicator

lights up.

On the Remote

DVD

Press

Page 58 4 August 2003 6:47 pm

so that the DVD indicator lights up.

Page 59

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 59 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Enter the password.

Press the enter a four-digit number as your password, then press

●

number keys

The 0 moves to “EXIT”.

Return to the OTHERS menu screen.

PARENTAL LOCK

COUNTRY CODE

SET LEVEL

PASSWORD

EXIT

SELECT

_ _ _ _

NEW PASSWORD

? •••

PRESS 0 ~ 9 KEY

TO EXIT, PRESS [SET UP MENU].

Press OK.

●

The “ OTHERS” menu resumes.

To return to the normal screen

SET UP MENU

Press

NOTE:

Remember your password, or make a note of it.

To change the settings

You can change the Parental lock settings later.

Access the Parental Lock screen.

A B C

●

Press the appropriate

keys

password, then press OK. If you enter the wrong password, “WRONG! RETRY...” appears at the bottom of the TV screen. Enter the correct password.

Press rt to select the country code, then press OK.

●

SET UP MENU

Press

. Press we to select “ OTHERS”. Press rt repeatedly to move 0 to “PARENTAL LOCK“, then press OK.

The “PARENTAL LOCK“ sub-menu appears on the TV screen. You can only move 0 to “PASSWORD” or to “EXIT” before you enter your password.

Enter the password.

number

to enter 4-digit

PARENTAL LOCK

COUNTRY CODE

SET LEVEL

PASSWORD

EXIT

SELECT

_ _ _ _

NEW PASSWORD

? •••

PRESS 0 ~ 9 KEY

TO EXIT, PRESS [SET UP MENU].

Change the country code.

See “Country/Area Code List for Parental Lock” ( When you change the country code, you must select the level.

墌

pg. 60).

Enter your new password.

Press the appropriate

number keys

to enter 4-digit

password, then press OK.

●

The password entered in the this step becomes the new password. If you do not change the password, enter the same password as in the stepB.

●

Even if you want to change only the country code and/or level, do not forget to enter the password after changing the country code and/or the level. Otherwise, the new country code and/ or the level will not become effective.

Return to the normal screen.

SET UP MENU

Press

NOTES:

●

When you enter the wrong password more than 3 times in stepB on the left column, the arrow moves to “EXIT” automatically and rt does not work.

●

If you forget your password, enter “8888” in stepB.

To temporarily release the Parental Lock

When you set the parental level strictly, some discs may not be played back at all. When you insert such a disc and try to play back it, the following Parental Lock screen appears on the TV screen, asking you whether you want the Parental Lock to be temporarily released or not.

Access the password screen.

Place the disc in the disc tray.

●

If the disc rated higher than the selected level, the following screen appears.

Press rt to move 0 to “TEMPORARY RELEASE”, then press OK.

●

If you select “NOT RELEASE”, you cannot play back that disc.

Enter the password.

Press the appropriate

number keys

password, then press OK.

●

If you enter the wrong password, “WRONG! RETRY...” appears on the TV screen. Enter the correct password.

●

If you enter the correct password, the Parental lock is released and the unit starts playback.

PARENTAL LOCK

TEMPORARY RELEASE

NOT RELEASE

PASSWORD

SELECT

_ _ _ _

PASSWORD? ••• PRESS 0 ~ 9 KEY

to enter 4-digit

Change the level.

Press rt to select the desired level, then press OK.

Page 59 4 August 2003 6:47 pm

NOTES:

●

When you enter the wrong password more than 3 times in stepB above, the arrow moves to “NOT RELEASE” automatically and rt do not work. In such a case, press OK, then press

●

If you forget your password, enter “8888” in stepB.

OPEN/CLOSE

(x) to remove the disc.

Page 60

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 60 Monday, August 4, 2003 7:24 PM

Country/Area Code List for Parental Lock

Masterpage:Left+

OPERATIONS ON DVD DECK (cont.)

AD AE AF AG AI AL AM AN AO AQ AR AS AT AU AW AZ BA BB BD BE BF BG BH BI BJ BM BN BO BR BS BT BV BW BY BZ CA CC CF CG CH CI CK CL CM CN CO CR CU CV CX CY CZ DE DJ DK DM DO DZ EC EE EG EH ER

Andorra United Arab Emirates Afghanistan Antigua and Barbuda Anguilla Albania Armenia Netherlands Antilles Angola Antarctica Argentina American Samoa Austria Australia Aruba Azerbaijan Bosnia and Herzegovina Barbados Bangladesh Belgium Burkina Faso Bulgaria Bahrain Burundi Benin Bermuda Brunei Darussalam Bolivia Brazil Bahamas Bhutan Bouvet Island Botswana Belarus Belize Canada Cocos (Keeling) Islands Central African Republic Congo Switzerland Côte d’Ivoire Cook Islands Chile Cameroon China Colombia Costa Rica Cuba Cape Verde Christmas Island Cyprus Czech Republic Germany Djibouti Denmark Dominica Dominican Republic Algeria Ecuador Estonia Egypt Western Sahara Eritrea

ES ET FI FJ FK FM FO FR FX GA GB GD GE GF GH GI GL GM GN GP GQ GR GS GT GU GW GY HK HM HN HR HT HU ID IE IL IN IO IQ IR IS IT JM JO JP KE KG KH KI KM KN KP KR KW KY KZ LA LB

Spain Ethiopia Finland Fiji Falkland Islands (Malvinas) Micronesia (Federated States of) Faroe Islands France France, Metropolitan Gabon United Kingdom Grenada Georgia French Guiana Ghana Gibraltar Greenland Gambia Guinea Guadeloupe Equatorial Guinea Greece South Georgia and the South Sandwich Islands Guatemala Guam Guinea-Bissau Guyana Hong Kong Heard Island and McDonald Islands Honduras Croatia Haiti Hungary Indonesia Ireland Israel India British Indian Ocean Territory Iraq Iran (Islamic Republic of) Iceland Italy Jamaica Jordan Japan Kenya Kyrgyzstan Cambodia Kiribati Comoros Saint Kitts and Nevis Korea, Democratic People’s Republic of Korea, Republic of Kuwait Cayman Islands Kazakhstan Lao People’s Democratic Republic Lebanon

Page 60 4 August 2003 6:47 pm

Page 61

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 61 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

LC LI LK LR LS LT LU LV LY MA MC MD MG MH ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ NA NC NE NF NG NI NL NO NP NR NU NZ OM PA PE PF PG PH PK PL PM PN PR PT PW PY QA RE RO RU RW

Saint Lucia Liechtenstein Sri Lanka Liberia Lesotho Lithuania Luxembourg Latvia Libyan Arab Jamahiriya Morocco Monaco Moldova, Republic of Madagascar Marshall Islands Mali Myanmar Mongolia Macau Northern Mariana Islands Martinique Mauritania Montserrat Malta Mauritius Maldives Malawi Mexico Malaysia Mozambique Namibia New Caledonia Niger Norfolk Island Nigeria Nicaragua Netherlands Norway Nepal Nauru Niue New Zealand Oman Pa na ma Peru French Polynesia Papua New Guinea Philippines Pa ki st a n Poland Saint Pierre and Miquelon Pitcairn Puerto Rico Portugal Pa la u Pa ra gu ay Qatar Réunion Romania Russian Federation Rwanda

SA SB SC SD SE SG SH SI SJ SK SL SM SN SO SR ST SV SY SZ TC TD TF TG TH TJ TK TM TN TO TP TR TT TV TW TZ UA UG UM US UY UZ VA VC VE VG VI VN VU WF WS YE YT YU ZA ZM ZR ZW

Saudi Arabia Solomon Islands Seychelles Sudan Sweden Singapore Saint Helena Slovenia Svalbard and Jan Mayen Slovakia Sierra Leone San Marino Senegal Somalia Suriname Sao Tome and Principe El Salvador Syrian Arab Republic Swaziland Turks and Caicos Islands Chad French Southern Territories To g o Thailand Tajikistan Tokelau Tu r km e n is t a n Tu n is i a To n ga East Timor Tu r ke y Trinidad and Tobago Tu va l u Taiwan, Province of China Tanzania, United Republic of Ukraine Uganda United States Minor Outlying Islands United States Uruguay Uzbekistan Vatican City State (Holy See) Saint Vincent and the Grenadines Ven ezuela Virgin Islands (British) Virgin Islands (U.S.) Viet Nam Vanuatu Wallis and Futuna Islands Samoa Ye m e n Mayotte Yu g o s l a v i a South Africa Zambia Zaire Zimbabwe

Page 61 4 August 2003 6:47 pm

Page 62

Filename [XVC33UM_08DVD.fm]

XVC33UM_08DVD.fm Page 62 Wednesday, September 3, 2003 3:30 PM

About MP3 Disc

This unit can playback CD discs recorded by the MP3 format (we refer to those discs as MP3 discs in this manual). Operations for MP3 discs are similar to those for Audio CD discs, though there are some restrictions and differences.

What is MP3?

MP3 is the abbreviation of “MPEG1 Audio Layer 3.” MPEG Audio is a compression specification that compresses the audio portion only. This image compression method is used in DVD or Video CD, etc. The audio data has been compressed into about 1/10.

On an MP3 disc, each material (song) is recorded on each Track (file), which usually belongs to a Group (folder).

Tra ck A.mp3

Tra ck B.mp3

Tra ck C.mp3

MP3 disc

Group 2

Group 1

Masterpage:Left+

OPERATIONS ON DVD DECK (cont.)

NOTES:

● Because of the disc characteristics or recording condition, some discs may not be played back or it takes time to start playback.

● The unit does not support “packet writing” discs.

● If there are any Tracks (files) which are stored on a disc directly

and do not belong to any Group (directory), the unit recognized them as belonging to an independent Group.

● The unit plays back Groups/Tracks on an MP3 disc in the alphabetical order.

● For example, if there are three title Groups [one], [two] and [three] on a disc, the playback order is [one], [three] then [two]. Tracks in a Group are played back in the same way.

● Therefore, an MP3 disc on the market may be played back in the different order from the order printed on its sleeve.

MP3 control display

The MP3 control display appears on the TV screen and playback starts when an MP3 disc is loaded.

Total group number on

disc

Current track number

Total track number

in current group

Track D.mp3

Track E.mp3

Group 4

This unit can recognize up to 99 Groups and up to 150 Tracks per Group. If a disc includes more than the Tracks above limit, the unit stops detecting Tracks when the number of detected Tracks reaches the limit and ignores the subsequent Tracks. The unit also ignores any non-MP3 file in the disc.

Track F.mp3

Group 3

NOTES for making a private MP3 disc using a CD-R/ CD-RW disc:

● Select “ISO9660” as the disc format.

● Finalize the disc.

Current group number

Current group

* Elapsed playing time of current track

Elapsed playing time is only shown during playback.

Current track

Total track number

on disc

Page 62 3 September 2003 3:29 pm

Page 63

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 63 Monday, August 4, 2003 7:24 PM

MP3 Playback

You can search and play back desired groups and tracks using the MP3 control display.

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Masterpage:Right-No-Heading

Using the MP3 control display

Turn on the unit.

POWER

Press

On the unit

VCR/DVD

Press lights up.

On the Remote

DVD

Press

Be sure to set “MP3/JPEG” to “MP3” before loading a disc. (

●

You cannot access the DVD Set Up screen and “X” appears on the TV screen if a disc is already placed.

(1).

Select the DVD deck.

repeatedly so that the DVD indicator

so that the DVD indicator lights up.

Select the mode.

墌

pg. 79)

NOTES:

●

PLAY

buttons function the same as with Audio CD discs, however,

REW

playback.

●

Resume playback, Program playback or Random playback also does not function for MP3 playback.

STOP

(4),

(3) and FF (5) buttons do not function for MP3

(8),

PAUSE

(9),

SKIP

(2) and

SKIP

(6)

Load the disc.

●

Press we to select the desired group.

Press rt to select the desired track, then press OK or

PLAY

●

Press

●

Press deck to open the disc tray, then remove the disc.

OPEN/CLOSE

Press disc tray. Place the MP3 disc in the disc tray.

For details, refer to “Placing a Disc” (

OPEN/CLOSE

Press disc tray.

The MP3 control display appears on the TV screen when an MP3 disc is loaded. (

(x) on the DVD deck to open the

墌

(x) on the DVD deck to close the

墌

pg. 62)

pg. 7).

Select the group.

Start playback.

(4).

You can skip a track across a group. Press the first track of the next group when the last track of the current group is selected.

SKIP

(6) to skip to

Pause playback.

PAUSE

To resume normal playback, press

(9).

PLAY

(4).

Stop playback.

STOP

(8). Press

OPEN/CLOSE

(x) on the DVD

Page 63 4 August 2003 6:47 pm

Page 64

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 64 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

OPERATIONS ON DVD DECK (cont.)

Repeat Playback

You can repeat playback of the current group, track or all groups.

●

While MP3 control display is on the TV:

Access the repeat mode.

PLAY SETUP

Press

●

The current repeat mode is displayed on the MP3 control display.

Select the mode.

Press rt to select the desired repeat mode, then press

●

Each time you press

TRACK]GROUP]ALL]OFF (No indication)](Back to the beginning)

during playback.

REPEAT

, the mode changes as follows:

Group/track selection

To start playback by specifying the group/track number

A B

Example: To select 3: Press 3. To select 14: Press +10, then 4. To select 20: Press +10, then 10.

To select 24: Press +10, +10, then 4. To select 110: Press +10 ten times, then 10.

●

TITLE

Press Press the number. Press the number.

The entered number appears in the track number indication and playback starts from the track you have specified.

number keys

Or press +10 twice, then 0.

(0-10, +10) to enter the group

(0-10, +10) to enter the track

TRACK

GROUP

ALL

OFF (no indication):

●

To stop Repeat Playback, press

●

To cancel Repeat Playback, press repeat mode display disappears on the TV screen.

●

You can also quit Repeat Playback in the following cases:

OPEN/CLOSE

• Press

• Turn off the unit.

To return to the MP3 control display

STOP

Press

(8).

The current track is played back repeatedly.

All tracks of the current group are played back repeatedly.

All tracks are played back repeatedly.

Each track is played back once.

STOP

(8).

REPEAT

repeatedly until the

(x) to open the disc tray.

Page 64 4 August 2003 6:47 pm

Page 65

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 65 Monday, August 4, 2003 7:24 PM

About JPEG Disc

This unit can playback CD discs recorded by the JPEG format (we refer to those discs as JPEG discs in this manual). Operations for JPEG discs are similar to those for Audio CD discs, though there are some restrictions and differences.

What is JPEG?

JPEG is the abbreviation of “Joint Photographic Expert Group.” JPEG is a still-picture data compression system.

On a JPEG disc, each still picture is recorded as a file, which usually belongs to a Group (folder).

File A.jpg

File B.jpg

File C.jpg

JPEG disc

Group 2

Group 4

Group 1

File D.jpg

File E.jpg

File F.jpg

Masterpage:Right-No-Heading

NOTES:

●

We recommend to record a file at 640 x 480 resolution. (If a file has been recorded at a resolution of more than 640 x 480, it will take a longer time to be displayed.)

●

This unit can only play back baseline JPEG files*. Progressive JPEG files* or lossless JPEG files* cannot be played back.

* Baseline JPEG format: Used for digital cameras, web, etc.

Progressive JPEG format: Used for web. Lossless JPEG format: An old type and rarely used now.

●

Some files on a JPEG disc may be played back distortedly.

●

Because of the disc characteristics or recording condition, some discs may not be played back or it takes time to start playback.

●

The unit does not support “packet writing” discs.

●

If there are any Files which are stored on a disc directly and do not belong to any Group (directory), the unit recognized them as belonging to an independent Group.

●

The unit plays back Groups/Files on an JPEG disc in the alphabetical order.

●

For example, if there are three title Groups [one], [two] and [three] on a disc, the playback order is [one], [three] then [two]. Files in a Group are played back in the same way.

●

Therefore, an JPEG disc on the market may be played back in the different order from the order printed on its sleeve.

JPEG control display

The JPEG control display appears on the TV screen and playback starts when a JPEG disc is loaded.

Total group number on

disc

Current file number

Total file number in

current group

Group 3

This unit can recognize up to 99 Groups and up to 150 Files per Group. If a disc includes more than the Files above limit, the unit stops detecting Files when the number of detected Files reaches the limit and ignores the subsequent Files. The unit also ignores any non-JPEG file in the disc.

NOTES for making a private JPEG disc using a CD-R/ CD-RW disc:

●

Select “ISO9660” as the disc format.

●

Finalize the disc.

Current group number

Current group

Current file

Total file number on

disc

Page 65 4 August 2003 6:47 pm

Page 66

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 66 Monday, August 4, 2003 7:24 PM

JPEG Playback

You can search and play back desired groups and files using the JPEG control display.

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Masterpage:Left+

OPERATIONS ON DVD DECK (cont.)

Using the JPEG control display

Turn on the unit.

POWER

Press

On the unit

VCR/DVD

Press lights up.

On the Remote

DVD

Press

Be sure to set “MP3/JPEG” to “JPEG” before loading a disc. (

●

You cannot access the DVD Set Up screen and “X” appears on the TV screen if a disc is already placed.

(1).

Select the DVD deck.

repeatedly so that the DVD indicator

so that the DVD indicator lights up.

Select the mode.

墌

pg. 79)

Load the disc.

●

Press we to select the desired group.

Press rt to select the desired file, then press OK or

PLAY

●

The slide-show playback starts from the selected file.

●

Press

●

OPEN/CLOSE

Press disc tray. Place the JPEG disc in the disc tray.

For details, refer to “Placing a Disc” (

OPEN/CLOSE

Press disc tray.

The JPEG control display appears on the TV screen when a JPEG disc is loaded. (

(x) on the DVD deck to open the

墌

(x) on the DVD deck to close the

墌

pg. 65)

pg. 7).

Select the group.

Start playback.

(4).

You can skip a file across a group. Press the first file of the next group when the last file of the current group is selected.

After selecting a file, press playback from the selected file, or press OK to show the selected file.

PLAY

SKIP

(6) to skip to

(4) to starts slide-show

Pause playback.

PAUSE

To resume normal playback, press

(9).

PLAY

(4).

Stop playback.

STOP

NOTES:

●

PLAY

buttons function the same as with Audio CD discs, however,

REW

playback.

●

Resume playback, Program playback or Random playback also does not function for JPEG playback.

Page 66 4 August 2003 6:47 pm

STOP

(4),

(3) and FF (5) buttons do not function for JPEG

(8),

PAUSE

(9),

SKIP

(2) and

SKIP

(6)

Press deck to open the disc tray, then remove the disc.

(8). Press

OPEN/CLOSE

(x) on the DVD

Page 67

Filename [XVC33UM_08DVD.fm]

XVC33UM_01.book Page 67 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Repeat Playback

You can repeat playback of the current group, file or all groups.

●

While JPEG control display is on the TV:

Access the repeat mode.

PLAY SETUP

Press displayed.

●

The current repeat mode is displayed on the JPEG control display.

Select the mode.

Press rt to select the desired repeat mode, then press

●

Each time you press

GROUP]ALL]OFF (No indication)](Back to the beginning)

while the JPEG Control screen is

REPEAT

, the mode changes as follows:

Group/file selection

To start slide-show playback by specifying the group/file number

A B

Example: To select 3: Press 3. To select 14: Press +10, then 4. To select 20: Press +10, then 10.

To select 24: Press +10, +10, then 4. To select 110: Press +10 ten times, then 10.

●

TITLE

Press Press the number. Press the number.

The slide-show playback starts from the file you have specified. To display only the selected file, then press OK. To start slideshow playback from that file, press OK again.

number keys

Or press +10 twice, then 0.

(0-10, +10) to enter the group

(0-10, +10) to enter the file

GROUP

ALL

OFF (No indication):

Start playback.

PLAY

Press

●

To stop Repeat Playback, press

●

To cancel Repeat Playback, press repeat mode display disappears on the TV screen.

●

You can also quit Repeat Playback in the following cases:

• Press

• Turn off the unit.

To return to the JPEG control display

Press

(4).

OPEN/CLOSE

STOP

(8).

All files of the current group are played back repeatedly.

All files are played back repeatedly.

Each file is played back once.

STOP

(8).

REPEAT

repeatedly until the

(x) to open the disc tray.

Zooming

ZOOM

Press

●

When you want to zoom the picture during slide-show playback, first press

●

For details, refer to “Zooming” (

during playback.

PAUSE

(9), then press

墌

pg. 45).

ZOOM

Page 67 4 August 2003 6:47 pm

Page 68

Filename [XVC33UM_09Editing.fm]

XVC33UM_01.book Page 68 Monday, August 4, 2003 7:24 PM

Edit From A

Masterpage:Left0

EDITING (VCR DECK)

You can use a camcorder as the source player and your unit as the recording deck.

Slide the

TV/VCR/DVD

switch to the right.

Camcorder

Make connections.

Connect the camcorder’s AUDIO OUT and VIDEO OUT connectors to the unit’s front panel AUDIO and VIDEO input connectors.

●

When using a monaural camcorder, connect its AUDIO OUT connector to the AUDIO L input connector on your unit.

●

When a Master Edit Control-equipped JVC camcorder is used, the camcorder is capable of controlling the unit. Refer to the camcorder’s instruction manual for operating procedure.

●

You can also use the AUDIO/VIDEO INPUT connectors on the rear panel.

Select the VCR deck.

On the unit

VCR/DVD

Press lights up.

On the Remote

VCR

Press

Set the unit’s input mode.

AUX (number key “0”

Press the front AUDIO/VIDEO input connectors, “L-1” for the rear AUDIO/VIDEO INPUT connectors, depending on the connectors being used.

repeatedly so that the VCR indicator

so that the VCR indicator lights up.

) and/or CH to select “F-1” for

VIDEO input

Recorder

Camcorder

Player

AUDIO input

Audio/video cable

(not supplied)

To Audio/VIDEO Output connectors

To EDIT

To PA U SE connector

Mini-plug cable (not provided) (JVC camcorder only)

Set the edit mode.

See “PICTURE CONTROL” on page 76.

Engage the Record Pause mode.

PLAY

Use point where you start recording, then press and hold

PAUSE

(9) and press

mode.

Start the camcorder.

Engage the Play mode of the camcorder.

Start the unit.

PLAY

Press

REW

(4),

(4) to engage the Record mode of the unit.

(3), or FF (5) to locate the

REC

(7) to engage the Record Pause

NOTES:

●

All necessary cables can be obtained from your dealer.

●

When you select “EDIT” to dub tapes in stepD, be sure to select “NORM” after you finish dubbing the tapes.

Page 68 4 August 2003 6:50 pm

Page 69

Filename [XVC33UM_09Editing.fm]

XVC33UM_01.book Page 69 Monday, August 4, 2003 7:24 PM

Edit To Or From

Masterpage:Right-No-Heading

You can use your unit as the source player or as the recording deck.

Slide the

TV/VCR/DVD

switch to the right.

Another Video Recorder

TV receiver

VCR channel or AV mode

TV receiver

Player

PTA

AALPTAL

Audio/video cable

Another recorder

Recorder

PTA

AALPTAL

Audio/video cable

Your unit

Make connections.

When using your unit as the source player ... ... connect its AUDIO/VIDEO OUTPUT connectors to the audio/video input connectors on another recorder.

When using your unit as the recording deck ... ... connect its AUDIO/VIDEO INPUT connectors to the audio/video output connectors on another recorder.

●

When you use your unit as the recording deck, you can also use the AUDIO/VIDEO input connectors on the front panel.

Select the VCR deck.

On the unit

VCR/DVD

Press lights up.

On the Remote

VCR

Press

Set the input mode of recording deck.

With this video unit, press

to select “F-1” for the front AUDIO/VIDEO input connectors, “L-1” for the rear AUDIO/VIDEO INPUT connectors, depending on the connectors being used.

●

When using another recorder as the recording deck, refer to its instruction manual.

Set the edit mode.

See “PICTURE CONTROL” on page 76.

Engage the Record Pause mode of the

repeatedly so that the VCR indicator

so that the VCR indicator lights up.

AUX (number key “0”

) and/or

recording deck.

VCR channel or AV mode

Audio/video cable

Player

Audio/video cable

Another recorder

Locate the point where you start recording, then engage the Record Pause mode.

Start the source player.

Engage the Play mode of the source player.

Start the recording deck.

Engage the Record mode of the recording deck.

NOTES:

●

All necessary cables can be obtained from your dealer.

●

When you select “EDIT” to dub tapes in stepD, be sure to select “NORM” after you finish dubbing the tapes.

●

When you use this unit as the source player for editing, be sure to set “SUPERIMPOSE” to “OFF” before starting. (

Page 69 4 August 2003 6:50 pm

墌

pg. 76)

Page 70

Filename [XVC33UM_09Editing.fm]

XVC33UM_01.book Page 70 Monday, August 4, 2003 7:24 PM

Dubbing

Masterpage:Left+

EDITING (VCR DECK) (cont.)

You can dub selected scenes from the DVD disc to a cassette, starting and stopping wherever you wish. However, it is not possible to dub the copy-protected disc. In such case, “ERROR” appears on the front display panel.

(from DVD to VCR)

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Load a cassette and place a disc.

For the VCR deck

Insert a cassette with the record safety tab intact.

For the DVD deck

B C

A B C

A B

Press and hold Remote.

●

OPEN/CLOSE

Press disc tray. Place the disc in the disc tray.

OPEN/CLOSE

Press disc tray.

(x) on the DVD deck to open the

(x) on the DVD deck to close the

Prepare the VCR deck for dubbing.

VCR

Press Press Search for the point where you want to start dubbing by pressing press

SP/EP

to select recording speed.

PLAY

(4), FF (5) or

STOP

(8).

REW

(3) then

Prepare the DVD deck for dubbing.

DVD

Press Search for the point where you want to start dubbing by pressing Press start point.

PLAY

(4), FF (5) or

PAUSE

(9) to pause playback a little before the

REW

(3).

Start dubbing.

REC

(7), then press

“DUB” lights on the front display panel.

PLAY

(4) on the

End dubbing.

STOP

Press

●

Be sure to press the unit.

●

If you press selected, the dubbing stopped, but the opening screen is also recorded.

(8).

STOP

(8) while the VCR indicator lights up on

EJECT

(8) or

(x) with the DVD deck

NOTES:

●

You cannot start dubbing when the scan mode is set to the progressive mode. Set it to the interlace mode. (

●

Set “ON SCREEN GUIDE” to “OFF” ( want to record the on-screen display for DVD discs during dubbing.

●

There may be a discrepancy of several seconds between where you intend editing to start, and where it actually starts.

●

The superimposed indication during the operation or dubbing is not recorded.

●

Set “PICTURE CONTROL” to “EDIT”. (

Page 70 4 August 2003 6:50 pm

墌

pg. 81) if you do not

pg. 76)

pg. 82)

Page 71

Filename [XVC33UM_09Editing.fm]

XVC33UM_01.book Page 71 Monday, August 4, 2003 7:24 PM

EDITING (DVD DECK)

Digital Audio

Masterpage:Right

You can dub selected audio from the DVD or Audio CD disc to a MD etc. However, it is not possible to dub the copy-protected disc.

Example: Dubbing to a MD

Dubbing

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

Rear of unit

TV/VCR/DVD

Recorder

Digital audio device (MD deck etc.)

Optical cable (not supplied)

switch to the right.

Player

Make connections.

Connect the optical cable between the unit and the digital audio device.

Place a disc and load a MD.

For the DVD deck

B C

For the digital audio device

Insert a MD.

A B

Select the input mode.

OPEN/CLOSE

Press disc tray. Place the disc in the disc tray.

OPEN/CLOSE

Press disc tray.

(x) on the DVD deck to open the

(x) on the DVD deck to close the

Prepare the DVD deck for dubbing.

DVD

Press Search for the point where you want to start dubbing by pressing press Press playback. Press start point.

and select the audio to be dubbed.

PLAY

(4), FF (5) or

STOP

(8).

REW

(3) a little, then press

PAUSE

(9) to pause playback a little before the

REW

PLAY

(3) then

(4) to start

Prepare the audio device for dubbing.

DIGITAL AUDIO OUT

Note for connection:

Remove the connector cover from the unit and remove the protection cap from the cable.

Start dubbing.

A B

Stop recording on the audio device. Then press to stop playback on the DVD deck.

PLAY

Press Start recording on the audio device.

(4) to start playback on the DVD deck.

End dubbing.

STOP

NOTES:

●

There may be a discrepancy of several seconds between where you intend editing to start, and where it actually starts.

●

You can also dub a Video CD or SVCD. Set “DIGITAL AUDIO OUTPUT” to “PCM ONLY”. (

墌

pg. 79)

(8)

Page 71 4 August 2003 6:50 pm

Page 72

Filename [XVC33UM_09Editing.fm]

XVC33UM_01.book Page 72 Monday, August 4, 2003 7:24 PM

Remote Control Functions

On the Remote

Keep pressing

Press the

“4”

for D.

VCR

down during steps A–B.

Change the remote control code.

number key “1”

for A,

“2”

for B,

Masterpage:Left0

REMOTE

“3”

for C or

Remote A/B/C/D Code Switching

The Remote is capable of controlling four JVC video units independently. Each of units can respond to one of four codes (A, B, C or D). The remote control is preset to send A code signals because your unit is initially set to respond to A code signals. You can easily modify your unit to respond to B, C or D code signals.

Before performing the following steps:

Slide the

TV/VCR/DVD

switch to the right.

Set the remote control code.

Press OK to set the code.

On the unit

Turn off the unit.

POWER

Press

PLAY

Press unit is turned off. The code currently set appears on the front display panel.

●

If the code displayed on the front display panel is different from the code set on the Remote, go to stepE.

STOP

Press the Remote will be applied to the unit.

(1).

Display the code.

(4) on the unit for over 5 seconds while the

Change the unit’s code.

(8) on the Remote. The code currently set on

NOTE:

Once you unplug the end of the mains power cord from the mains, the remote control code is back to A.

Page 72 4 August 2003 6:50 pm

Page 73

Filename [XVC33UM_09Editing.fm]

XVC33UM_01.book Page 73 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

TV Multi-Brand Remote Control

Your Remote can operate the basic functions of your TV set. In addition to JVC TVs, other manufacturer’s TVs can also be controlled.

Before performing the following steps:

●

Turn off the TV using its Remote.

●

Slide the

TV/VCR/DVD

switch to the left.

Set the TV brand code.

Keep pressing Enter your TV’s brand code using the press OK.

POWER

Press and try operations (

●

Once you have set the remote control to operate the TV, you do not have to repeat this step until you replace your Remote’s batteries.

●

Some brands of TV have more than one code. If the TV does not function with one code, try entering another.

Press the corresponding button:

TV/VCR CH +/–, TV VOL+/–

Muting),

●

For some brands of TV, you must press OK after having pressed

number keys

the

BRAND NAME CODE

JVC HITACHI MAGNAVOX MITSUBISHI PANASON IC RCA SHARP SONY SAMSUNG SANYO SEARS TOSHIBA ZENITH

VCR

down during stepA.

number keys

(1) on the unit’s Remote to turn on the TV

墌

stepB).

Operate the TV.

number keys

POWER

(Volume),

01, 03 10 02 03 04, 11 05 06 07 12 13 13 08 09

(1),

MUTE

, then

TV/VCR

(TV

IMPORTANT

Although the supplied remote control unit is compatible with JVC televisions, as well as many other models, it may not work with your TV, or in some instances, may have limited function capability.

Page 73 4 August 2003 6:50 pm

Page 74

Filename [XVC33UM_09Editing.fm]

XVC33UM_01.book Page 74 Monday, August 4, 2003 7:24 PM

REMOTE (cont.)

Masterpage:Left+

Connecting To A Dolby Digital Decoder or An Amplifier With A Built-in DTS

(DVD deck only)

These instructions enable you to connect your unit to dolby digital decoder or amplifier with a built-in DTS.

DIGITAL AUDIO OUT

To DIGITAL AUDIO input

Dolby Digital decoder or amplifier with a built-in DTS

Optical cable (not supplied)

Make connections.

Connect the optical cable between the unit and the Dolby Digital decoder or amplifier with a built-in DTS.

NOTES:

●

For Dolby digital sound, set “DIGITAL AUDIO OUTPUT” to “DOLBY DIGITAL/PCM”. (

●

For DTS sound, set “DIGITAL AUDIO OUTPUT” to “STREAM/

墌

PCM”. (

pg. 79)

墌

pg. 79)

Back of unit

Note for connection:

Remove the connector cover from the unit and remove the protection cap from the cable.

CAUTIONS:

●

This unit has a dynamic range of more than 80 dB with regards to its Hi-Fi audio capability. It is recommended that you check the maximum level if you are going to listen to the Hi-Fi audio signals through a stereo amplifier. A sudden surge in the input level to the speakers may damage them.

●

Some speakers and televisions are specially shielded to prevent television interference. If both are of the non-shielded type, do not place the speakers adjacent to the TV set as this can adversely affect the video playback picture.

Page 74 4 August 2003 6:50 pm

Page 75

Filename [XVC33UM_10Subsidiary.fm]

XVC33UM_01.book Page 75 Monday, August 4, 2003 7:24 PM

SUBSIDIARY SETTINGS

Mode Set

Masterpage:Right

You can change various mode settings on the Function Set screen by following the procedure described below.

●

For each mode setting, see pages 76 to 77.

(VCR deck)

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Turn on the unit.

POWER

Press

On the unit

VCR/DVD

Press lights up.

On the Remote

VCR

Press

SET UP MENU

Press

Press rt to move the highlight bar (arrow) to “FUNCTION SET”, then press OK or e.

Press rt to move the highlight bar (arrow) to the item you want to change.

(1).

Select the VCR deck.

repeatedly so that the VCR indicator

so that the VCR indicator lights up.

Access the Main Menu screen.

Access the Function Set screen.

Select the mode.

Select the mode setting.

Press OK or e.

Return to the normal screen.

SET UP MENU

Press

Page 75 4 August 2003 6:42 pm

Page 76

Filename [XVC33UM_10Subsidiary.fm]

XVC33UM_01.book Page 76 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

SUBSIDIARY SETTINGS (cont.)

PICTURE CONTROL

NORM

EDIT SOFT SHARP

SUPERIMPOSE

OFF

AUTO SP]EP TIMER

OFF

* The default setting is

This feature helps you to adjust the playback picture quality according to your preference. Normally select “NORM”.

NORM

: Picture quality is adjusted automatically.

EDIT

: Minimizes picture degradation during editing (recording and playback).

SOFT

: Reduces image coarseness when viewing overplayed tapes containing a

SHARP

lot of noise. Clearer, sharper-edged picture when viewing images with lots of flat,

same-coloured surfaces such as cartoons.

bold

in the table below.

NOTES:

●

When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will not change until you select another mode.

●

When you select “EDIT” to dub tapes, be sure to select “NORM” after you finish dubbing the tapes.

When this function is set to “ON”, various operational indicators appear on the TV screen. Messages appear in the selected language. (

墌

pg. 20)

NOTES:

●

When you use this unit as the source player for editing, be sure to set “SUPERIMPOSE” to “OFF” before starting.

●

During playback, the operation mode indicators may be disturbed depending on the type of tape being used.

When this function is set to “ON”, the unit automatically switches to EP mode to allow complete recording if there is not enough tape to record the entire program while timer-recording in SP mode.

For Example:

Recording a program of 140 minutes in length onto a 120-minute tape

Approximately 110 minutes Approximately 30 minutes

SP mode EP mode

Total 140 minutes

Make sure you set this function to “ON”, before the timer-recording starts.

NOTES:

●

If you have programed the unit to timer-record 2 or more programs, the second program and those thereafter may not fit on the tape if you set “AUTO SP]EP TIMER” to “ON”. In this case, make sure the mode is not engaged, then set the tape speed manually during timer programing.

●

In order to ensure that the recording fits on the tape, this feature may leave a slight nonrecorded section at the end of the tape.

●

There may be some noise and sound disturbance at the point on the tape where the unit switches from SP to EP mode.

●

The Auto SP the feature will not work properly on the following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120

]

EP Timer feature is not available during ITR (Instant Timer Recording), and

Page 76 4 August 2003 6:42 pm

Page 77

Filename [XVC33UM_10Subsidiary.fm]

XVC33UM_01.book Page 77 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

VIDEO STABILIZER

OFF

BLUE BACK

OFF

2ND AUDIO RECORD

OFF

* The default setting is

When this function is set to “ON”, you can automatically correct vertical vibration in the picture when playing back unstable recordings made on another recorder.

bold

in the table below.

NOTES:

●

When you finish viewing a tape, be sure to set this function to “OFF”.

●

Regardless of the setting, this function has no effect during recording and during special effects playback.

●

The on-screen display may jitter vertically when this function is set to “ON”.

●

To watch recordings with close-caption, set this function to “OFF”.

When this function is set to “ON”, the TV screen becomes all blue when receiving a channel not in use.

NOTE:

When you want to receive an unstable channel with poor signals, set this function to “OFF”.

●

When this function is set to “ON”;

If a SAP program is received, the SAP audio is recorded on both the normal and Hi-Fi tracks. The main audio is not recorded. If a non-SAP program is received, the main audio is recorded on both the Hi-Fi and normal tracks.

●

When this function is set to “OFF”,

the SAP audio cannot be recorded.

NOTES:

When the channel is changed on the unit;

●

The “STEREO” indicator appears on the screen for about 5 seconds if the program is a stereo broadcast.

●

The “SAP” indicator appears on the screen for about 5 seconds if the program is a SAP broadcast.

●

Both indicators appear when a stereo program is accompanied by SAP sound.

AUDIO MONITOR

HI-FI

HI-FI L HI-FI R NORM MIX

AUTO POWER OFF

OFF

This unit can record two sound tracks simultaneously (normal and Hi-Fi) on a Hi-Fi stereo tape. You can select the sound track(s) to listen to while playing back a Hi-Fi stereo tape. In addition, when playing back a prerecorded tape containing two separate audio programs on the Hi-Fi tracks, you can choose either one by selecting either “HI-FI L” or “HI-FI R”.

HI-FI

: Normally select this. Hi-Fi sound is played back.

HI-FI L

: Sound on the left Hi-Fi channel is played back.

HI-FI R

: Sound on the right Hi-Fi channel is played back.

NORM

: Sound on the normal track is played back.

MIX

: Both sounds on the Hi-Fi track and normal track are mixed

and played back.

NOTES:

●

While playing back a monaural tape, sounds on the normal track will be heard regardless of this setting.

●

You can also use the

墌

sound. (

When this function is set to “3H”, the unit is turned off automatically if no operation is done within 3 hours. “AUTO POWER OFF IN 3 MIN” appears on the screen 3 minutes before the unit is turned off.

pg. 32)

A.MONITOR

button on the Remote to select the desired monitor

Page 77 4 August 2003 6:42 pm

Page 78

Filename [XVC33UM_10Subsidiary.fm]

XVC33UM_01.book Page 78 Monday, August 4, 2003 7:24 PM

Mode Set

(DVD deck)

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

TV/VCR/DVD

switch to the right.

Masterpage:Left+

SUBSIDIARY SETTINGS (cont.)

●

The procedure shows how to set “RESUME” to “ON” on the DVD Set Up menu screen as an example.

Turn on the unit.

POWER

Press

On the unit

VCR/DVD

Press lights up.

On the Remote

DVD

Press

Press we to select “ OTHERS”.

●

Each time you press the button, the setup menus change as follows;

(1).

Select the DVD deck.

repeatedly so that the DVD indicator

so that the DVD indicator lights up.

Access the DVD Set Up menu screen.

SET UP MENU

OTHERS

RESUME

ON SCREEN GUIDE

PARENTAL LOCK

SELECT

USE TO SELECT, USE OK TO CONFIRM. TO EXIT, PRESS [SET UP MENU].

You can change various mode settings on the Mode Set screen by following the procedure described below.

●

For each mode setting, see pages 79 to 81.

墌

pg. 22)

墌

pg. 79)

pg. 22)

墌

pg. 18, 79)

pg. 79)

pg. 21)

LANGUAGE

PICTURE

MENU LANGUAGE ( AUDIO LANGUAGE ( SUBTITLE ( ON SCREEN LANGUAGE (

MONITOR TYPE ( PICTURE SOURCE ( SCREEN SAVER ( MP3/JPEG (

墌

LANGUAGE

]

(Back to the beginning)

Select the mode.

Press rt to move 0 to “RESUME”, then press OK.

Select the mode setting.

Press rt to select “ON”, then press OK.

Return to the normal screen.

SET UP MENU

Press

]

PICTURE]AUDIO ]OTHERS

DIGITAL AUDIO OUTPUT (

AUDIO

OTHERS

Page 78 4 August 2003 6:42 pm

ANALOG DOWN MIX ( D. RANGE CONTROL ( OUTPUT LEVEL (

RESUME ( ON SCREEN GUIDE ( PARENTAL LOCK (

墌

pg. 81)

墌

墌墌

pg. 80)

pg. 81)

墌

pg. 58)

pg. 79)

墌

pg. 80) pg. 80)

Page 79

Filename [XVC33UM_10Subsidiary.fm]

XVC33UM_01.book Page 79 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Picture Settings

MONITOR TYPE

16:9 NORMAL 16:9 AUTO

4:3 LB

4:3 PS

PICTURE SOURCE

VIDEO (NORMAL) VIDEO (ACTIVE) FILM

AUTO

SCREEN SAVER

OFF

* The default setting is

You can select the monitor type depending the TV used when you play back DVD VIDEO discs recorded for wide-screen TVs. For more details, refer to “Monitor Set (DVD deck)” (

You can obtain optimal picture quality by selecting whether the content on the disc is processed by field (video source) or by frame (film source). Normally set to “AUTO”.

VIDEO (NORMAL)

Suitable for playing back a video source disc with relatively a

VIDEO (ACTIVE)

FILM

: Suitable for playing back a film or progressive source disc.

AUTO

: Used to play back a disc containing both video and film

●

If the playback picture is unclear or noisy, or the oblique lines of the picture are rough, try to change to other modes.

The TV screen may be burned out if a static picture is displayed for a long time. When this function is set to “ON”, the unit automatically activates the screen saver function if a static picture, such as an on-screen display or menu is displayed for over 5 minutes.

few moments.

: Suitable for playing back a video source disc with relatively a lot of movements.

source materials. This unit recognizes the picture type (film or video source) of the current disc according to the disc information.

墌

pg. 18)

bold

in the table below.

MP3/JPEG

MP3

JPEG

Audio Settings

DIGITAL AUDIO OUTPUT

PCM ONLY DOLBY DIGITAL/PCM

STREAM/PCM

NOTE:

This function is not available for Audio CDs and MP3 discs.

You can select files to play back, when both MP3 files and JPEG files are recorded on a disc.

MP3

: Select this to play back MP3 files.

JPEG

: Select this to play back JPEG files.

NOTE:

You cannot access the DVD Set Up screen and “X” appears on the TV screen if a disc is already placed.

* The default setting is

Set to the appropriate mode according to the type of the device connected to DIGITAL AUDIO OUT connector on the rear of unit. It is not necessary to set this mode when you connect no device to DIGITAL AUDIO OUTconnector.

PCM ONLY

DOLBY DIGITAL/PCM

STREAM/PCM

: Select this when you connect the unit’s DIGITAL AUDIO OUT connector to the linear PCM digital input connector of other audio device.

: Select this when you connect the unit’s DIGITAL AUDIO OUT connector to the digital input connector of a Dolby Digital decoder or an amplifier with a built-in Dolby Digital decoder.

: Select this when you connect the unit’s DIGITAL AUDIO OUT connector to the digital input connector of an amplifier with a builtin DTS, Dolby Digital, or MPEG multichannel decoder.

bold

in the table below.

Page 79 4 August 2003 6:42 pm

Page 80

Filename [XVC33UM_10Subsidiary.fm]

XVC33UM_01.book Page 80 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

SUBSIDIARY SETTINGS (cont.)

ANALOG DOWN MIX

DOLBY SURROUND

STEREO

D. RANGE CONTROL

WIDE RANGE

NORMAL

TV MODE

Set to the appropriate mode according to your audio system when you play back a DVD VIDEO disc recorded with surround multichannel audio. This setting affects only the analogue audio output signal from the AUDIO OUTPUT connectors (DVD) when playing back a DVD VIDEO disc recorded with surround multichannel audio.

DOLBY SURROUND

STEREO

: Select this when you enjoy conventional 2-channel stereo

Select this when you enjoy multichannel surround audio by connecting the unit’s analogue AUDIO OUTPUT connector (DVD) to a surround decoder or an internal amplifier.

audio by connecting the unit’s analogue AUDIO OUTPUT connectors (DVD) to a stereo amplifier/receiver or TV, or when you dub audio of a DVD VIDEO disc recorded with surround audio to your MD, cassette, etc.

NOTE:

The “ANALOG DOWN MIX” function does not work when the 3D Phonic function is activated. (

The dynamic range (the difference between the loudest sound and the quietest one) can be compressed during playback of a program encoded in Dolby Digital format. This function takes effect when a DVD VIDEO disc recorded in Dolby Digital format is played back at low or middle volume.

墌

pg. 46)

WIDE RANGE

NORMAL

TV MODE

: Normally select this setting to activate this function.

: Select this when you hear the sound through the TV's

: Select this to inactivate this function when you enjoy wide

dynamic range program.

speaker(s).

OUTPUT LEVEL

STANDARD

LOW

NOTES:

●

This function works only when playing back a disc recorded with Dolby Digital format. The setting is not effective for other discs.

●

This function does not work when the 3D Phonic function is activated. (

You can lower the output level of analog audio to accommodate the unit to the connected A/V equipment.

STANDARD

LOW

: Normally select this.

: The output level of analog audio is lowered.

墌

pg. 46)

Page 80 4 August 2003 6:42 pm

Page 81

Filename [XVC33UM_10Subsidiary.fm]

XVC33UM_01.book Page 81 Monday, August 4, 2003 7:24 PM

Masterpage:Right-No-Heading

Playback discs

DVD VIDEO with 48 kHz, 16/20/24 bit linear PCM

DVD VIDEO with DTS DTS bitstream 44.1 kHz, 16 bit stereo linear PCM

DVD VIDEO with Dolby Digital

Audio CD/Video CD 44.1 kHz, 16 bit stereo linear PCM

Audio CD with DTS DTS bitstream 44.1 kHz, 16 bit stereo linear PCM

MP3 disc Linear PCM

STREAM/PCM DOLBY DIGITAL/PCM PCM ONLY

48 kHz, 16 bit linear PCM

Dolby Digital bitstream

Output

48 kHz, 16 bit stereo linear

PCM

NOTES:

●

The unit is not equipped with the DTS decoding function.

●

When you play back a DVD VIDEO or Audio CD disc with DTS, use a DTS decoder to get correct signals from your speakers. Never use the unit’s analog output connectors, which output incorrect signals that may damage your speakers.

●

If you connect the analog outputs and digital outputs simultaneously, be sure to select the source of the amplifier correctly, or set the level control of the amplifier connected to the analog outputs to minimum.

Others Settings

RESUME

OFF DISC RESUME

* The default setting is

When this function is set to “ON”, you can use the resume function.

墌

(

pg. 45)

: You can start playback from the resume point of the

OFF

: You cannot use the resume function.

DISC RESUME

placed disc.

: The unit retains a memory of the resume points of the last 30 discs played back, even though they have been ejected.

bold

in the table below.

ON SCREEN GUIDE

OFF

NOTE:

This function is not available for Audio CDs and MP3 discs.

When this function is set to “ON”, the unit can display “on-screen guide” icons or characters which shows the conditions of the unit or disc.

Page 81 4 August 2003 6:42 pm

Page 82

Filename [XVC33UM_10Subsidiary.fm]

XVC33UM_01.book Page 82 Monday, August 4, 2003 7:24 PM

Masterpage:Left+

SUBSIDIARY SETTINGS (cont.)

Child Lock

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

You can disable the unit’s operation.

Press and hold than 10 seconds while the unit is turned on. The unit turns off, and “CL“ appears on the front display panel.

●

To release the child lock, press and hold Remote until the unit turns on.

NOTES:

●

When the child lock function is in use, keep the Remote out of the children’s reach.

●

Timer recording programs will be performed even if the child lock function activated.

TV/VCR/DVD

Set the Child Lock.

POWER

(1) on the Remote for more

switch to the right.

POWER

(1) on the

Scan Mode Set

(DVD deck)

●

Turn on the TV and select the VCR channel (or AV mode).

●

Slide the

This unit supports the progressive scan system (eg. 480p*) as well as the conventional interlaced scan system (eg. 480i*). If your TV equipped with component video connectors supports the progressive video input, you can enjoy a high quality picture by setting the progressive scan mode to active.

●

Refer also to the instruction manuals supplied with your TV.

●

If your TV equipped with component video connectors does not support the progressive video input, do not change the scan mode to the “PROGRESSIVE”.

* 480p and 480i indicate the number of scanning lines and

scanning format of an image signal.

• 480p indicates 480 scanning lines with progressive format.

• 480i indicates 480 scanning lines with interlaced format.

During playback or while stopped, press and hold

PROGRESSIVE SCAN

for more than 3 seconds, to change the scan mode between Progressive and Interlace mode.

TV/VCR/DVD

Switch the mode.

on the unit or

switch to the right.

DVD

on the Remote

Page 82 4 August 2003 6:42 pm

Page 83

Filename [XVC33UM_11Trouble.fm]

XVC33UM_01.book Page 83 Monday, August 4, 2003 7:24 PM

TROUBLESHOOTING

Masterpage:Right

Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your unit off for repair.

POWER

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. No power is supplied to the unit.

2. The Remote won’t function.

●

The AC power cord is disconnected. Connect the AC power cord.

●

The batteries are discharged. Replace the dead batteries with new ones.

TAPE TRANSPORT (VCR deck)

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. During recording, the tape does not

2. The tape will not rewind or fast-

䡬

run. “

” lights up on the front display

panel.

forward.

●

The unit is in the Record Pause mode. Press

●

The tape is already fully rewound or fast-forwarded.

PLAY

(4) to resume recording.

Check the cassette.

PLAYBACK (VCR deck)

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. The VCR deck can not be operated.

2. The playback picture does not appear while the tape is running.

3. Noise appears during visual search.

4. Noise appears during normal playback.

5. The playback picture is blurred or interrupted while TV broadcasts are clear or “USE CLEANING CASSETTE” message appears on the screen.

6. Breaks are noticeable in Hi-Fi soundtrack.

●

The VCR deck is not selected.

●

If you are using the RF connection, — the TV receiver’s channel selector is not set to the VCR channel. — the unit’s VCR channel has not been correctly set.

●

If you are using the AV, S-VIDEO* or Component Video* connection, the TV receiver is not set to the AV mode.

* (DVD deck only)

●

This is normal. —

●

The automatic tracking mode is engaged.

●

The video heads may be dirty. Use a dry cleaning cassette ECL-3F, or

●

The automatic tracking mode is engaged.

On the unit

VCR/DVD

Press VCR indicator lights up.

On the Remote

VCR

Press up.

If you are using the RF connection, — set the TV receiver to the VCR channel. — perform “Set the VCR channel.”

墌

(

pg. 13).

If you are using the AV or S-VIDEO*, Component Video* connection, set the TV to its AV mode.

* (DVD deck only)

Try manual tracking. (

consult your JVC dealer.

Try manual tracking. (

repeatedly so that the

so that the VCR indicator lights

墌

pg. 32)

墌

pg. 32)

Page 83 4 August 2003 6:50 pm

Page 84

Filename [XVC33UM_11Trouble.fm]

XVC33UM_01.book Page 84 Monday, August 4, 2003 7:24 PM

PLAYBACK (DVD deck)

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. The button do not work.

2. The DVD deck can not be operated.

3. “X” appears on the TV screen.

4. “REGION CODE ERROR!” appears on the TV screen.

5. The disc cannot be played back.

6. The language is not played back as you set.

7. Changing audio/subtitle language is not possible.

8. The subtitles do not appears on the TV screen.

9. Angle cannot be changed.

Masterpage:Left+

TROUBLESHOOTING (cont.)

●

The operation is prohibited on the placed disc.

●

The DVD deck is not selected.

●

The operation is prohibited on the placed disc.

●

The disc’s region number does not match that of the unit.

●

The disc’s region number does not match that of the unit.

●

This type of the disc cannot be played back.

●

The disc is not placed properly. Remove the disc, then place the disc

●

The Parental Lock is engaged, and the placed disc is rated higher than the set level.

●

The disc does not contain the language you set.

●

The disc does not contain the audio/ subtitle in the multiple languages.

●

The disc does not contain the subtitles. —

●

The subtitle display is set to off. Set the subtitles display to on. (

●

A-B Repeat Playback is in progress.

墌

(

pg. 51)

●

The scene is not recorded from the multiple angles.

On the unit

VCR/DVD

Press DVD indicator lights up.

On the Remote

DVD

Press lights up.

Use the discs whose region number includes “ALL” or “4”. (

See “Unplayable Discs” (

properly in the disc tray. ( “Placing a Disc”)

Release the Parental Lock temporarily

墌

(

墌

(

With some discs, the language should be set on the top menu. (

The subtitles recorded around A-B point may not appear.

so that the DVD indicator

pg. 59), or change the set level pg. 59).

—

repeatedly so that the

—

墌

pg. 5)

墌

pg. 5)

墌

pg. 5).

墌

pg. 7,

—

墌

pg. 43)

—

墌

pg. 54)

Page 84 4 August 2003 6:50 pm

Page 85

Filename [XVC33UM_11Trouble.fm]

XVC33UM_01.book Page 85 Monday, August 4, 2003 7:24 PM

MP3 Playback (DVD deck)

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. A disc cannot be played.

2. Not MP3 files but JPEG files are played.

3. The MP3 control display appears on the TV screen, but no operation can be performed.

Masterpage:Right-No-Heading

●

No MP3 files are recorded to the disc. Replace the disc.

●

MP3 files do not have the correct file extension in their file names.

●

MP3 files are not recorded in a format compliant with ISO 9660 Level 1 or 2.

●

The different types of files are recorded to the disc.

●

The MP3/JPEG setting is set to “JPEG”. When both MP3 files and JPEG files are

●

No MP3 files or JPEG files are recorded to the disc, or the disc is an unplayable disc (such as CD-ROM).

Add correct file extension (.mp3, .MP3 or any uppercase and lowercase combination such as “.Mp3”) to their file names.

Replace the disc. (Record MP3 files using a compliant application.)

The disc which contains the different types of files may not be played because of its disc characteristics or recording conditions.

recorded to a disc, set “MP3/JPEG” to “MP3” to play MP3 files. (

Replace the disc. (

墌

pg. 7)

墌

pg. 79)

JPEG Playback (DVD deck)

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. A disc cannot be played.

2. Not JPEG files but MP3 files are played back.

●

No JPEG files are recorded to the disc. Replace the disc.

●

JPEG files do not have the correct file extension in their file names.

●

JPEG files are not recorded in a format compliant with ISO 9660 Level 1 or 2.

●

The MP3/JPEG setting is set to “MP3”. When both MP3 files and JPEG files are

RECORDING (VCR deck)

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. Recording cannot be started.

2. TV broadcasts cannot be recorded.

3. Tape-to-tape editing is not possible.

4. Camcorder recording is not possible.

䡬

5. “

” and “$” on the front display

panel won’t stop blinking.

●

There is no cassette loaded, or the cassette loaded has had its record safety tab removed.

●

“F-1” or “L-1” has been selected as the input mode.

●

The source (another video recorder, camcorder) has not been properly connected.

●

All necessary power switches have not been turned on.

●

The input mode is not correct. Set the input mode to “F-1” or “L-1”.

●

The camcorder has not been properly connected.

●

The input mode is not correct. Set the input mode to “F-1” or “L-1”.

●

The end of the tape was reached during recording.

Add correct file extension (.jpg, .jpeg, .JPG, .JPEG or any uppercase and lowercase combination such as “.Jpg”) to their file names.

Replace the disc. (Record JPEG files using a compliant application.)

recorded to a disc, set “MP3/JPEG” to “JPEG” to play JPEG files. (

Insert a cassette, or using adhesive tape, cover the hole where the tab was removed.

Set to the desired channel.

Confirm that the source is properly connected.

Confirm that all units’ power switches are turned on.

Confirm that the camcorder is properly connected.

The program may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire program.

墌

pg. 79)

Page 85 4 August 2003 6:50 pm

Page 86

Filename [XVC33UM_11Trouble.fm]

XVC33UM_01.book Page 86 Monday, August 4, 2003 7:24 PM

TIMER RECORDING (VCR deck)

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. Timer recording won’t work.

2. Timer programing is not possible.

3. “#” on the front display panel won’t stop blinking.

4. “#”, “

5. “#” blinks for 10 seconds and the

6. “

7. “N”, “

䡬

display panel won’t stop blinking.

Timer mode is disengaged.

panel won’t stop blinking.

” and “$” on the front

䡬

” and “$” on the front display

䡬

” and “$” on the front display

●

The clock and/or the timer have been set incorrectly.

●

The timer is not engaged. Press

●

Timer recording is in progress. Timer programing can’t be performed

●

The timer is engaged but there’s no cassette loaded.

●

The loaded cassette has had its record safety tab removed.

●

The end of the tape was reached during timer recording.

●

TIMER

no programs in memory, or the timer record information has been programed incorrectly.

●

The end of the tape was reached during Instant Timer Recording.

●

The loaded cassette has had its record safety tab removed.

●

The end of the tape was reached during Satellite Auto Recording.

has been pressed when there are

Masterpage:Left+

TROUBLESHOOTING (cont.)

Re-perform the clock and/or timer settings.

TIMER

displayed on the front display panel.

while a timer recording is in progress. Wait until it finishes.

Load a cassette with the record safety tab intact.

Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact.

The program may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire program.

Check the programed data and reprogram as necessary, then press again.

The program may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire program.

Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact.

The program may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire program.

and confirm that “#” is

TIMER

Page 86 4 August 2003 6:50 pm

Page 87

Filename [XVC33UM_11Trouble.fm]

XVC33UM_01.book Page 87 Monday, August 4, 2003 7:24 PM

QUESTIONS AND ANSWERS

PLAYBACK

Q. What happens if the end of the tape is reached

during playback or search?

The tape is automatically rewound to the beginning.

Q. During search, slow, still and frame-by-frame

playback, I can’t hear any audio. What’s the problem?

This is normal.

Q. Can the unit indefinitely remain in the still

mode?

No. It stops automatically after 5 minutes to protect the heads.

Q. When returning from search to normal

playback, the picture is disturbed. Should I be concerned about this?

No, it is normal.

Q. Noise bar appear during search. What’s the

problem?

This is normal.

Q. Sometimes, during Index Search, the unit can’t

find the program I want to see. Why not?

There may be index codes too close together.

TIMER RECORDING

Q. “䡬” and “#” remain lit on the front display

panel. Is there a problem?

No. This is a normal condition for a timer recording in progress.

Q. Can I program the timer while I’m watching a

tape or a TV broadcast?

You won’t see the picture as it is replaced by the on-screen menu, but the audio from the program or tape you’re viewing can be heard.

RECORDING

Q. When I pause and then resume a recording, the

end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen?

This is normal. It reduces distortion at the pause and resume points.

Q. Can the unit indefinitely remain in the Record-

Pause mode?

No. The unit goes to its Stop mode automatically after 5 minutes to protect the heads.

Q. What happens if the tape runs out during

recording?

The unit stops recording, and “䡬” and “$” on the front display panel won’t stop blinking.

Page 88 4 August 2003 6:50 pm

Page 89

Filename [XVC33UM_11Trouble.fm]

XVC33UM_11Trouble.fm Page 89 Wednesday, May 12, 2004 1:40 PM

Masterpage:Right0

SPECIFICATIONS

GENERAL

Power requirement : AC 110 – 220 Vd, 50 Hz/60 Hz Power consumption

Power on : 25 W Power off : 4.9 W

Temperature

Operating : 5°C to 40°C

Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (WxHxD)

: 435 mm x 93 mm x 272 mm Weight : 4.4 kg Format : VHS NTSC standard Maximum recording time

(SP) : 210 min. with ST-210 video cassette (EP) : 630 min. with ST-210 video cassette

VIDEO/AUDIO (VCR deck)

Signal system : NTSC colour signal and EIA

monochrome signal, 525 lines/ 60 fields

Recording system : DA4 (Double Azimuth) head helical

scan system Signal-to-noise ratio: 45 dB Horizontal resolution

: 230 lines

Frequency range : 70 Hz to 10,000 Hz (Normal audio)

20 Hz to 20,000 Hz (Hi-Fi audio) Input/Output : RCA connectors:

IN x 2, OUT x 1

EN 89

TUNER

Tuning system : Frequency synthesized tuner Channel coverage

VHF : Channels 2 – 13 UHF : Channels 14 – 69 CATV : 113 Channels

RF output : Channel 3 or 4 (switchable; preset

to Channel 3 when shipped) 75 ohms, unbalanced

TIMER

Clock reference : Quartz Program capacity : 1-year programmable timer/

8 programs

Memory backup time

: Approx. 3 minutes

ACCESSORIES

Provided accessories

: RF cable,

Infrared remote control unit, “AA” battery x 2, Conversion plug

Specifications shown are for SP mode unless otherwise specified. E.& O.E. Design and specifications subject to change without notice.

VIDEO/AUDIO (DVD deck)

Signal system : NTSC Applicable disc : DVD (12 cm, 8 cm)

Audio characteristics

DVD : 4 Hz – 22 KHz

Frequency response

CD : 4 Hz – 20 KHz S/N Ratio : 90 dB Harmonic distortion

Wow and flutter : Below Measurable Level Dynamic range : 90 dB Output

Component-Y : (RCA) 1.0 Vp-p/75 ohm

Component-P

Audio : (RCA) 2 Vrms, 1 Kohm

Digital Audio : (COAXIAL) 0.5 Vp-p/75 ohm

CD (12 cm, 8 cm)

: 0.1 %

B/PR

: (RCA) 0.7 Vp-p/75 ohm

(OPTICAL) –21 dBm to –15 dBm (peak)

Page 89 12 May 2004 1:40 pm

Page 90

Filename [XVC33UM_12IX.fm]

XVC33UM_12IX.fm Page 90 Wednesday, August 6, 2003 5:11 PM

Masterpage:Left0

LIST OF TERMS

A-B Repeat Playback About Discs

.............................................................. 65

JPEG

.............................................................. 62

MP3

Placing a Disc

Playable Discs

Region Number

Unplayable Discs Angle Selection Audio Channel Selection Audio Language Selection Auto Channel Set

............................................ 51

.................................................. 7

.................................................. 5

................................................ 5

.............................................. 5

.................................................... 55

....................................... 57

..................................... 56

................................................. 26

Chapter Search Check, cancel and change programs Child Lock Clock Set Component Video Connection Connecting To A Dolby Digital Decoder or

An Amplifier With A Built-in DTS

.................................................... 52

....................... 38

.......................................................... 82

............................................................ 24

............................... 15

...................... 74

Digital Audio Dubbing Disc menu Dubbing (from DVD to VCR)

.......................................................... 43

.......................................... 71

................................. 70

EDITING (DVD DECK)

Digital Audio Dubbing EDITING (VCR DECK)

Dubbing (from DVD to VCR) EDITING (VCR)

Edit From A Camcorder

Edit To Or From Another Video Recorder Elapsed Recording Time Indication Express Timer Programing

..................................... 71

............................ 70

.................................... 68

......................... 35

..................................... 36

Group/file selection Group/track selection

.............................................. 67

........................................... 64

High-Speed (Turbo) Search High-Speed Search

.................................... 29

............................................... 44

.................................................................. 8

INDEX Index Search Instant ReView Instant Timer Recording (ITR)

........................................................ 30

..................................................... 30

................................. 34

........... 69

Language

Letter Box Locating the start point of the item or skip the item

............................................................ 20

Language Code List Menu/Audio/Subtitle Language Set

(DVD deck only) On-screen Language Set (DVD deck) On-screen Language Set (VCR deck)

............................................................ 19

.......................................... 23

........................................ 22

................. 21

.................. 20

Manual Channel Set Manual Tracking Mode Set (DVD deck)

ANALOG DOWN MIX AUDIO LANGUAGE D. RANGE CONTROL DIGITAL AUDIO OUTPUT MENU LANGUAGE MONITOR TYPE MP3/JPEG ON SCREEN GUIDE ON SCREEN LANGUAGE OUTPUT LEVEL PICTURE SOURCE RESUME SCREEN SAVER SUBTITLE

Mode Set (VCR deck)

2ND AUDIO RECORD AUDIO MONITOR AUTO POWER OFF AUTO SP]EP TIMER BLUE BACK PICTURE CONTROL SUPERIMPOSE VIDEO STABILIZER

Monitor Set (DVD deck)

MONITOR TYPE

MP3 control display

.............................................. 27

.................................................. 32

..................................... 80

....................................... 22

..................................... 80

............................... 79

......................................... 22

....................................... 19, 79

...................................................... 79

........................................ 81

................................. 21

.............................................. 80

.......................................... 79

........................................................ 81

............................................... 79

....................................................... 22

.................................... 77

.......................................... 77

........................................ 77

...................................... 76

.................................................... 77

........................................ 76

................................................ 76

......................................... 77

....................................... 19, 79

.............................................. 62

Next Function Memory

......................................... 31

OPERATIONS ON DVD DECK OPERATIONS ON VCR DECK

........................ 42–67

......................... 28–41

.... 44

JPEG control display

Page 90 August 6, 2003 5:11 pm

............................................. 65

Page 91

Filename [XVC33UM_12IX.fm]

XVC33UM_01.book Page 91 Monday, August 4, 2003 7:24 PM

Masterpage:Right-NoTitle0

Pan&Scan Parental Lock

Playback (DVD deck) Playback (JPEG) Playback (MP3) Playback (VCR deck) Playback Control (PBC) Function Plug&Play Set Program Playback

........................................................... 19

Country/Area Code List To change the settings To set Parental Lock for the first time To temporarily release the Parental Lock

............................................ 66–67

............................................. 63–64

...................................................... 16

................................................ 53

.................................... 60

..................................... 59

.................. 58

.................................... 42–53

..................................... 28–32

.......................43, 51

Random Playback Record One Program While Watching Another Recording Recording Resume Function Region Number Remote Control Functions Repeat Playback Resume Function

................................................ 53

.................................................... 33–35

.................................. 33

..................................................... 5

..................................... 72

................................. 31, 50, 64, 67

................................................. 45

Satellite Auto Recording Scan Mode Set (DVD deck) Second Audio Recording Skip Search Slow Motion Soundtrack Selection Still Picture/Frame-By-Frame Playback Subtitle Selection S-VIDEO Connection

......................................................... 30

...................................................29, 45

........................................ 41

................................... 82

....................................... 35

............................................ 32

...............29, 45

................................................. 54

............................................ 14

............ 59

........ 34

Tape Position Indicator Tape Remaining Time Time Search Timer Recording Top menu Tuner Set

......................................................... 51

............................................................ 43

............................................................. 26

.......................................... 11

........................................... 35

............................................36–41

VFP function

........................................................ 47

When programs overlap each other

Zooming

3D Phonic

....................................................... 45, 67

........................................................... 46

......................... 40

Page 91 August 4, 2003 6:52 pm

Page 92

Filename [XVC33UM_13Cov4.fm]

XVC33UM_13Cov4.fm Page 92 Monday, May 10, 2004 6:45 PM

HR-XVC33UM

Printed in Beijing

Page 92 May 10, 2004 6:45 pm

0504-TY-ID-BJ1