DVD PLAYER &
VIDEO CASSETTE RECORDER
HR-XVC27UM
INSTRUCTIONS
Antes de operar su equipo, lea cuidadosamente este instructivo.
¡ATENCION!
LPT0967-001A
2 EN
Dear Customer,
Thank you for purchasing the JVC DVD player & VHS video
cassette recorder. Before use, please read the safety
information and precautions to ensure safe use of your new
unit.
CAUTIONS
WARNING : DANGEROUS VOLTAGE INSIDE
WARNING : TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
The POWER `/! button does not completely shut off
mains power from the unit, but switches operating
current on and off. “`” shows electrical power
standby and “ ! ” shows ON.
CAUTION:
A DVD/VCR IS A CLASS 1 LASER PRODUCT.
HOWEVER THIS DVD/VCR USES A VISIBLE LASER
BEAM WHICH COULD CAUSE HAZARDOUS
RADIATION EXPOSURE IF DIRECTED. BE SURE TO
OPERATE THE UNIT CORRECTLY AS INSTRUCTED.
WHEN THIS DVD/VCR IS PLUGGED INTO THE
WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE
TO THE OPENING OF THE DISC TRAY AND OTHER
OPENINGS TO LOOK INTO THE INSIDE OF THIS
DVD/VCR.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
IMPORTANT
It may be unlawful to record or play back copyrighted
material without the consent of the copyright owner.
CAUTION
8 When you are not using the unit for a long period
of time, it is recommended that you disconnect the
power cord from the AC outlet.
8 Dangerous voltage inside. Refer internal servicing
to qualified service personnel. To prevent electric
shock or fire hazard, remove the power cord from
the AC outlet prior to connecting or disconnecting
any signal lead or aerial.
8 Changes or modifications not approved by JVC
could void user’s authority to operate the
equipment.
The rating plate and safety caution are on the rear of
the unit.
This unit is produced to comply with Standard IEC
60065.
POWER SYSTEM:
This set operates on voltage of AC 110 – 220Vd, 50/60
Hz with automatic switching.
Use the conversion plug (provided) depending on the
type of your AC WALL outlet.
CLASS 1 LASER PRODUCT
REPRODUCTION OF LABELS
WARNING LABEL INSIDE OF THE UNIT
EN 3
A
Use only discs marked with the following.
DVD
(8 cm /12 cm disc)
Video CDs
(8 cm /12 cm disc)
Audio CDs
(8 cm /12 cm disc)
SVCD
(8 cm /12 cm disc)
● Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
● “DTS” and “DTS 2.0 + Digital Out” are trademarks of Digital
Theater Systems, Inc.
● Cassettes marked “VHS” (or “S-VHS”) can be used with this
unit. However, S-VHS recording is not possible with this
model.
● This model is equipped with SQPB (S-VHS QUASI
PLAYBACK) that makes it possible to play back S-VHS
recordings with regular VHS resolution.
● HQ VHS is compatible with existing VHS equipment.
● This product incorporates copyright protection technology
that is protected by method claims of certain U.S. patents and
other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
viewing users only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or disassembly
is prohibited.
When the equipment is installed in a cabinet or a shelf,
make sure that it has sufficient space on all sides to allow
for ventilation (10 cm or more on both sides, on top and
at the rear.)
When discarding batteries, environmental problems must
be considered and the local rules or laws governing the
disposal of these batteries must be followed strictly.
Failure to heed the following precautions may result in
damage to the unit, Remote or video cassette.
1. DO NOT
place the unit —
— in an environment prone to extreme temperatures
or humidity.
— in direct sunlight.
— in a dusty environment.
— in an environment where strong magnetic fields are
generated.
— on a surface that is unstable or subject to vibration.
2. DO NOT
block the unit’s ventilation openings or
holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to
get out.)
3. DO NOT
4. DO NOT
place heavy objects on the unit or Remote.
place anything which might spill on top of
the unit or Remote.
(If water or liquid is allowed to enter this equipment,
fire or electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or
splashing.
6. DO NOT
use this equipment in a bathroom or places
with water. Also DO NOT place any containers filled
with water or liquids (such as cosmetics or medicines,
flower vases, potted plants, cups, etc.) on top of this
unit.
7. DO NOT
place any naked flame sources, such as
lighted candles, on the apparatus.
8. AVOID violent shocks to the unit during transport.
MOISTURE CONDENSATION
Moisture in the air will condense on the unit when you
move it from a cold place to a warm place, or under
extremely humid conditions—just as water droplets form
in the surface of a glass filled with cold liquid. Moisture
condensation on the head drum will cause damage to the
tape. In conditions where condensation may occur, keep
the unit turned on for a few hours to let the moisture dry.
TTENTION
To mobile phone users:
Using a mobile phone in the vicinity of the unit may
cause picture vibration on the TV screen or change
the screen to a blue back display.
On placing the unit:
Some TVs or other appliances generates strong
magnetic fields. Do not place such appliance on top
of the unit as it may cause picture disturbance.
4 EN
CONTENTS
DISC INFORMATION 5
About Discs ......................................................... 5
INDEX 8
INSTALLING YOUR NEW UNIT 12
Basic Connections ............................................. 12
S-VIDEO Connection (DVD deck only) ............. 13
Component Video Connection
(DVD deck only) ............................................ 14
INITIAL SETTINGS 15
Plug & Play Set .................................................. 15
Monitor Set (DVD deck) .................................... 16
Language ........................................................... 18
Clock Set ........................................................... 22
Tuner Set ........................................................... 24
OPERATIONS ON VCR DECK 26
Basic Playback .................................................. 26
Playback Features .............................................. 27
Basic Recording ................................................ 31
Recording Features ............................................ 32
Express Timer Programming .............................. 34
Satellite Auto Recording .................................... 39
EDITING (VCR DECK) 66
Edit From A Camcorder ..................................... 66
Edit To Or From Another Video Recorder .......... 67
Dubbing (from DVD to VCR) ............................. 68
EDITING (DVD DECK) 69
Digital Audio Dubbing ...................................... 69
REMOTE 70
Remote Control Functions ................................. 70
Connecting To A Dolby Digital Decoder
or An Amplifier With A Built-in DTS
(DVD deck only)
............................................ 71
SUBSIDIARY SETTINGS 72
Mode Set (VCR deck) ......................................... 72
Mode Set (DVD deck) ........................................ 75
Child Lock ......................................................... 78
Scan Mode Set (DVD deck) ............................... 78
TROUBLESHOOTING 79
QUESTIONS AND ANSWERS 84
SPECIFICATIONS 85
OPERATIONS ON DVD DECK 40
Basic Playback .................................................. 40
Playback Features .............................................. 41
Using the on-screen bar .................................... 46
Parental Lock .................................................... 56
About MP3 Disc ................................................ 60
MP3 Playback ................................................... 61
About JPEG Disc ............................................... 63
JPEG Playback ................................................... 64
LIST OF TERMS 86
DISC INFORMATION
About Discs
Playable Discs
You can use the discs with the following logos for playback
only.
DVD VIDEO
(8 cm /12 cm disc)
Video CD/Super Video CD
(8 cm /12 cm disc)
EN 5
Unplayable Discs
The following types of discs cannot be played using this unit.
Do not attempt to play back any kind of disc that is damaged
(cracked, warped, or repaired with adhesive tape) or discs in
unusual shapes (heart-shaped, octagonal, or other forms). If such
discs are accidentally played back, it may cause noise that can
lead to speaker damage.
● CD-ROM discs (including PHOTO-CD)
● DVD AUDIO discs
● Super Audio CDs (SACD)
● DVD-RW discs recorded in VR format
● DVD-RAM
● Discs which have a region number other than “4”
DIGITAL VIDEO
Audio CD
(8 cm /12 cm disc)
CD-DA
files
● The following discs also can be played back.
• DVD-R/RW discs recorded in DVD VIDEO format and
finalized
• CD-R/RW discs recorded in Super Video CD, Video CD or
Audio CD format and finalized.
• CD-R/RW discs recorded in MP3 format in accordance with
the “ISO 9660” format. (See page 60 for details.)
• CD-R/RW discs recorded in JPEG format in accordance with
the “ISO 9660” format. (See page 63 for details.)
● Discs other than the above cannot be played back.
● Operation and audio quality of this unit are not guaranteed for
discs that do not conform to the Compact Disc specification
(CD-DA).
Before you play back a CD, check for the CD logo and read
the notes on the package to confirm that it conforms to the
Compact Disc specification.
● Depending on the intentions of the author of the software,
recording conditions of DVD discs and Video CD discs may
be restricted. Since this unit plays back discs according to the
intentions of the author of the software as indicated on the
disc, some functions may not operate as commanded.
● When switching from the first layer to the second layer of
double-layered DVD VIDEO discs, the image and sound may
be momentarily distorted. This is not a malfunction.
VIDEO CD
Region Number
The world is divided into 6 regions for DVD VIDEO discs. DVD
VIDEO discs are assigned a region number to indicate which
region they may be played back in. A disc cannot be played
back on this unit unless the region number of the disc matches
that of the unit. The region number for this unit is “4”. Only discs
whose region number includes “4” can be played back such as
shown below.
Examples of DVD VIDEO labels which can be played back
using this unit.
Marks of discs in this instruction manual
Allows operation
with a DVD VIDEO
disc.
Allows operation
with a Video CD
disc.
Allows operation
with a disc
including MP3 files.
Allows operation
with a Audio CD
disc.
Allows operation
with a SVCD disc.
Allows operation
with a disc
including JPEG files.
6 EN
DISC INFORMATION (cont.)
DVD VIDEO Marks
Sometimes marks are printed on a DVD disc and/or on its
packaging to indicate information regarding the contents and
functions of a disc. Check marks indicating the contents and
functions of a disc. Note, however, that in some cases a disc
may not include a mark even for a function it supports.
Marks related to video
Mark Description
Number of subtitles
Number of angles
Recorded under the standard 4:3 aspect
ratio
Screen includes black bands at top and
bottom of image which has a standard 4:3
aspect ratio (letter box)
Video playback is in Wide video mode
(16:9) on wide televisions, but in letter
box on televisions with standard 4:3
aspect ratio.
File Structure of Discs
DVD VIDEO
Typically, DVD VIDEO discs are made up of larger units called
“titles”. Each title has a number (title number) that can be used
to select desired titles. Titles are further divided into units called
“chapters”. Each chapter has a number (chapter number) that
can also be used to select desired chapters. Note that some discs
are not divided into titles and chapters.
Title 1 Title 2
Chapter 1 Chapter 2Chapter 1Chapter 3Chapter 2
Audio CD/Video CD
Typically, Audio CD discs are divided into separate tracks each
containing one song. Each track is assigned a number. For
example, the third track is Track 3. The same is true for Video
CD discs.
Track 1 Track 4Track 3Track 2
NOTE:
Video CD discs that support Playback Control (PBC)
The still image or motion image which follows a menu screen is
called a “scene”. Each scene has a scene number.
For more details, refer to “Locating a desired scene using the
menu of the Video CD with PBC” (
墌 pg. 41).
Video playback is in Wide video mode
(16:9) on wide televisions, but pan and
scan is used on televisions with standard
4:3 aspect ratio (either the left or right side
of the image is cut-out).
Marks related to audio
Mark Description
Number of audio tracks
Dolby Digital mark
Dolby Laboratories has developed a
digital surround system for the home. This
mark indicates that you may enjoy 5.1channel audio (front left and right, center,
rear left and right, and a channel for LFE
(Low-Frequency Effects)).
DTS (Digital Theater System)
The DTS decoder on this unit enables you
to enjoy DTS audio with the connected
TV’s speakers by converting 5.1 channel
audio signals into 2 channel signals (DTS
Down Mixing). The decoder also outputs
the original DTS 5.1 channel audio
signals from the DIGITAL AUDIO OUT
connector on this unit.
EN 7
Placing a Disc
1 Open the disc tray.
Press OPEN/CLOSE (x) on the DVD deck to open the
disc tray.
x
● Pressing the button again closes the disc tray.
● Do not block the disc tray with your hand while it is opening
or closing as this may result in hardware failure.
● Do not place unplayable discs or any object other than a disc
in the disc tray.
● Do not press down strongly on the disc tray or place any
heavy objects on it.
2 Place the disc.
Place the disc in the disc tray
with the label side facing up.
● Since disc size changes depending
on the disc to be played back, be
sure to correctly align the disc with
the grooves for its size. If the disc is
not in its groove, it may be
scratched or otherwise damaged.
● To insert an 8 cm disc, place it
according to the inner groove.
Care and Handling of Discs
How to handle discs
When handling a disc, do
not touch the surface of the
disc. Since discs are made
of plastic, they are easily
damaged. If a disc gets
dirty, dusty, scratched or
warped, the images and
sound will not be picked up
correctly, and such a disc may cause the unit to malfunction.
Label side
Do not damage the label side, stick paper to or use any adhesive
on its surface.
Storage
Make sure that discs are kept in their cases. If discs are piled on
top of one another without their protective cases, they can be
damaged. Do not put discs in a location where they may be
exposed to direct sunlight, or in a place where the humidity or
temperature is high. Avoid leaving discs in your car!
Maintenance of discs
If there are fingerprints or other dirt
adhering to a disc, wipe with a soft dry
cloth, moving from the center outwards.
If a disc is difficult to clean, wipe with a
cloth moistened with water. Never use
record cleaners, petrol, alcohol or any
anti-static agents.
CAUTION
Sometimes during playback, noise or images may be
garbled. This is sometimes due to the disc. (It may not be up
to industry standards.)
These symptoms are caused by the discs, not by the
malfunction of the unit.
8 EN
FRONT VIEW
INDEX
A Power Button (POWER (1)) 墌 pg. 16
B VCR Indicator 墌 pg. 26, 31
C VHS Cassette Loading Slot
D VCR/DVD Button 墌 pg. 26, 31, 40
E Disc Tray
F Stop Button (STOP (8)) 墌 pg. 26, 31, 40
G DVD Indicator 墌 pg. 40
H Play Button (PLAY (4)) 墌 pg. 26, 40
I DVD Open/Close Button (OPEN/CLOSE (x))
墌 pg. 40
J VHS Eject Button (EJECT (x)) 墌 pg. 26, 31
K Video/Audio Input Connectors (VIDEO/AUDIO)
墌 pg. 66
L Remote Sensor
M Front Display Panel 墌 pg. 9
N Record Button (REC (7)) 墌 pg. 31
O Rewind Button (REW (3)) 墌 pg. 26, 27, 42
P Fast Forward Button (FF (5)) 墌 pg. 26, 27, 42
Q Channel Button (CH +/–) 墌 pg. 31
R Progressive Scan Button (PROGRESSIVE SCAN)
墌 pg. 78
REAR VIEW
EN 9
A Region Number Label 墌 pg. 5
B AC Power Cord 墌 pg. 12
C S-video Output Connector (S VIDEO OUTPUT)*
墌 pg. 13
D Audio/Video Output Connectors (AUDIO/
VIDEO OUTPUT) 墌 pg. 12, 13, 14, 67
E Antenna Input Connector (VHF/UHF IN)
墌 pg. 12
* These connectors are only for DVD deck.
FRONT DISPLAY PANEL
A Operation Mode Indicators
B Channel/Clock
Auxiliary Input Mode Display (F-1) (VCR deck
only)
Counter Display (VCR deck)
Tape Speed (SP/EP) (VCR deck only)
Multi-information window* (DVD deck)
* The current group/title/track/chapter number(s), time and status
information.
F Digital Audio Output Connector
(DIGITAL AUDIO OUT)* 墌 pg. 69
G Component Video Output Connectors
(COMPONENT VIDEO OUT)* 墌 pg. 14
H Audio Output Connectors (AUDIO OUTPUT
(L/R))*
I Remote Pause Connector 墌 pg. 66
J Antenna Output Connector (VHF/UHF OUT)
墌 pg. 12
C VCR Indicator 墌 pg. 32
D Progressive Mode Indicator 墌 pg. 78
E “Timer” Indicator (VCR deck only) 墌 pg. 35
F Satellite Auto Recording Indicator (N) (VCR deck
only) 墌 pg. 39
10 EN
INDEX (cont.)
ON-SCREEN DISPLAY (VCR deck)
If you press ON SCREEN on the Remote when “SUPERIMPOSE” is set to “ON” (墌 pg. 73), various operational
indicators appear on the TV screen.
For On-screen display for DVD deck, refer to “Using the on-screen bar” (墌 pg. 46).
A Operation Mode Indicators
B Tape Speed (SP/EP)
C Tape Position Indicator
The tape position indicator
appears on the TV screen
when you press REW (3)
or FF (5) from the Stop
mode or perform an Index
Search. (
墌 pg. 28) The
position of “q” in relation to
“B” (beginning) or “E” (end)
shows you where you are
on the tape.
Beginning End
NOTE:
Depending on the type of tape being used, the tape position
indicator may not appear correctly.
D Index number 墌 pg. 28
E Tape Remaining Time Indicator 墌 pg. 33
F Counter Display
G Audio Mode Display 墌 pg. 30
H SAP Indicator 墌 pg. 33
I Stereo Program Indicator 墌 pg. 33
J Day/Clock Display
K Channel Position Number/Auxiliary Input
Indicator (F-1)
L “Cassette Loaded” Mark
To recall an indication
A Press ON SCREEN.
● All indications corresponding to the current status are
displayed for 5 seconds. After that, the counter
information and RECORD/PAUSE if in the Record
Pause mode, remain on the screen.
B Press ON SCREEN again to clear the display.
● The RECORD/PAUSE indication remains on the screen.
EN 11
REMOTE
Buttons with a small dot on the left side of the name (POWER
(1), TV/VCR, TV/VCR CH +/–, TV VOL+/–, MUTE) can
also be used to operate a JVC’s TV after setting the TV/VCR/
DVD switch to the left.
A VCR Button 墌 pg. 26, 31
B TV/VCR/DVD switch 墌 pg. 16
C Menu Button (MENU) 墌 pg. 41
D SP/EP Button 墌 pg. 31
Top Menu Button (TOP MENU) 墌 pg. 41
E Stop Time Button (STOP +/–) 墌 pg. 34
On-Screen Button (ON SCREEN) 墌 pg. 10, 46
F Start Time Button (START +/–) 墌 pg. 34
Repeat Button (REPEAT) 墌 pg. 48, 62, 65
Zooming Button (ZOOM) 墌 pg. 43
G Number Keys 墌 pg. 25, 31, 62
H Daily Button (DAILY) 墌 pg. 35
I Reset Button (C.RESET) 墌 pg. 33
Cancel Button (CANCEL) 墌 pg. 37
10 Button
J Play Button (PLAY (4)) 墌 pg. 26, 40
K Rewind Button (REW (3)) 墌 pg. 26, 27, 42
L Stop Button (STOP (8)) 墌 pg. 26, 31, 40
M Record Button (REC (7)) 墌 pg. 31
N Reverse Skip/Index Button (SKIP/INDEX (2))
墌 pg. 28, 41
Review Button ( )
O rt Button 墌 pg. 16
TV/VCR Channel Button (TV/VCR CH +/–)
墌 See the left column
P Set Up Button (SET UP) 墌 pg. 16
Q 3D-Phonic Button (3D-PHONIC) 墌 pg. 44
R TV Volume Button (TV VOL+/–) 墌 See the left
column
S DVD Button 墌 pg. 40
T Power Button (POWER (1)) 墌 pg. 16, left
column
U TV Muting Button (MUTE) 墌 See the left column
Audio Monitor Button (A.MONITOR)
墌 pg. 30, 54, 55
V TV/VCR Button 墌 pg. 32, left column
W Date Button (DATE +/–) 墌 pg. 34
Subtitle Button (SUB TITLE) 墌 pg. 52
Angle Button (ANGLE) 墌 pg. 53
X Channel Button (CH +/–) 墌 pg. 31
Y Programming Button (PROG.) 墌 pg. 34
Z Timer Button (TIMER) 墌 pg. 35
a Weekly Button (WEEKLY) 墌 pg. 35
b Program Check Button (PROG. CHECK)
墌 pg. 36
Return Button (RETURN) 墌 pg. 41
c Satellite Auto Recording Button (REC LINK)
墌 pg. 39
d +10 Button
e Auxiliary Button (AUX) 墌 pg. 66
f Fast Forward Button (FF (5)) 墌 pg. 26, 27, 42
g Pause Button (PAUSE (9)) 墌 pg. 27, 31
h Forward Skip/Index Button (SKIP/INDEX (6))
墌 pg. 28, 41
i ENTER Button 墌 pg. 16
j we Button 墌 pg. 16
k Display Button (DISPLAY) 墌 pg. 33
l Skip Search Button (SKIP SEARCH) 墌 pg. 28
DVD Picture Button (DVD PICTURE) 墌 pg. 45
How To Use
Before use, insert two AA size batteries into the Remote with
the polarity ( and ) matched correctly as indicated on
the battery compartment or on the lid.
The Remote can operate most of your unit’s functions, as
well as basic functions of TV sets of JVC. (
column)
● Point the Remote toward the remote sensor.
● The maximum operating distance of the remote control is
about 8 m.
墌 See the left
NOTE:
If the Remote doesn’t work properly, remove its batteries,
wait a short time, replace the batteries and then try again.
12 EN
Basic Connections
Antenna or Cable
Coaxial cable
Flat feeder
Matching transformer
(not supplied)
AC Outlet
AC Power Cord
Back of unit
AUDIO OUTPUT
VIDEO OUTPUT
VHF/UHF
IN
INSTALLING YOUR NEW UNIT
Connect the unit to TV.
C
The connection method you use depends on the type of
TV you have.
RF Connection
8 To connect to a TV with NO AV input connectors —
A Disconnect the TV antenna from the TV.
B Connect the TV antenna cable to the VHF/UHF IN
connector on the rear panel of the unit.
C Connect the supplied RF cable between the VHF/UHF
OUT connector on the rear panel of the unit and the
TV’s antenna terminal.
AV Connection
8 To connect to a TV with AV input connectors —
A Connect the antenna, unit and TV as per “RF
Connection”.
B Connect an optional audio/video cable between the
AUDIO/VIDEO OUTPUT connectors on the rear
panel of the unit and the TV’s audio/video input
connectors.
● Set your TV to AV mode.
● For switching the TV’s mode, refer to the instruction manual of
your television.
● To obtain high-quality pictures, you can also use the S-VIDEO
connection or Component Video Connection. (DVD deck
only) (
墌 pg. 13, 14)
Audio/video cable
(not supplied)
To Audio/video
input connectors
It’s essential that your unit be properly connected.
THESE STEPS MUST BE COMPLETED BEFORE ANY
VIDEO OPERATION CAN BE PERFORMED.
Check the contents.
A
Make sure the package contains all of the accessories
listed in “SPECIFICATIONS” on page 85.
Situate the unit.
B
Place the unit on a stable, horizontal surface.
VHF/UHF OUT
RF cable
(supplied)
To 75 ohm
Terminal
TV
Connect the unit to power source.
D
Plug the end of the AC power cord into an AC outlet.
Set the VCR channel.
E
The VCR channel is the channel on which you can watch
the picture from the unit on the TV when only using RF
connection.
With RF connection, set the VCR channel to “3 CH” or
“4 CH”.
● The VCR channel is preset to “3 CH”. Set to “4 CH” if the
Channel 3 is used for broadcasting in your area.
With AV connection, set the VCR channel to “– CH” (off).
To set the VCR channel, perform the following steps:
Before performing the following steps:
● Make sure there is no cassette inserted in the unit.
● Make sure the unit is turned on, then press VCR/
DVD on the unit or VCR on the Remote so that the
VCR indicator lights up.
A When the unit is turned off, press STOP (8) on the unit
for more than 5 seconds. “3 CH” appears on the front
display panel.
B Press CH +/– on the Remote to select “3 CH”, “4 CH”
or “– CH” (off), then press ENTER.
● If Plug&Play or Tuner setting has not previously been
performed, the Language Select screen appears and Plug&Play
takes place automatically.
S-VIDEO
A
Connection
(DVD deck only)
TTENTION
Be sure to connect the unit’s VIDEO OUTPUT (DVD/
VCR) connector to the TV’s VIDEO input connector.
Antenna or Cable
Coaxial cable
Flat feeder
Matching transformer
(not supplied)
AC outlet
AC power
cord
Back of unit
S-Video cable
(not supplied)
S VIDEO OUTPUT
Audio/video
(not supplied)
AUDIO OUTPUT
VIDEO OUTPUT
VHF/
UHF IN
cable
VHF/UHF
OUT
EN 13
8 To connect to a TV with S-VIDEO/AUDIO input
connectors . . .
Connect the unit to TV.
A
A Connect the antenna, unit and TV as per “AV
Connection” (
B Connect the unit’s S VIDEO OUTPUT (DVD)
connector to the TV’s S-VIDEO input connector.
Connect the unit to power source.
B
Plug the end of the AC power cord into an AC outlet.
Set the VCR channel to off.
C
Before performing the following steps:
● Make sure there is no cassette inserted in the unit.
● Make sure the unit is turned on, then press VCR/
DVD on the unit or VCR on the Remote so that the
VCR indicator lights up.
A When the unit is turned off, press STOP (8) on the unit
for more than 5 seconds. “3 CH” appears on the front
display panel.
B Press CH +/– on the Remote to select “– CH” (off),
then press ENTER.
● If Plug&Play or Tuner setting has not previously been
performed, the Language Select screen appears and Plug&Play
takes place automatically.
墌 pg. 12).
NOTES:
● You can obtain high-quality S-VIDEO pictures.
● If your TV is not stereo-capable, use the unit’s AUDIO
OUTPUT connectors to connect to an audio amplifier for
Hi-Fi stereo sound reproduction.
● To operate the unit with your TV using the S-VIDEO
connection, set your TV to its AV mode. You can also use the
TV/VCR button on the unit’s Remote to set JVC TV to the AV
mode.
● For switching the TV’s mode, refer to the instruction manual of
your television.
● Only DVD picture is output from S-VIDEO OUTPUT
connector. (VCR picture is not output.)
To S-VIDEO input
connector
RF cable
(supplied)
To 75 ohm
Terminal
TV
14 EN
A
Component Video
Connection
(DVD deck only)
INSTALLING YOUR NEW UNIT (cont.)
8 To connect to a TV with component video input
connectors . . .
Connect the unit to TV.
A
A Connect the aerial, unit and TV as per “AV
Connection” (
B Connect the unit’s COMPONENT VIDEO OUT
connectors to the TV’s component video input
connectors.
墌 pg. 12).
TTENTION
Be sure to connect the unit’s VIDEO OUTPUT (DVD/
VCR) connector to the TV’s VIDEO input connector.
Antenna or Cable
Coaxial cable
Flat feeder
Matching transformer
(not supplied)
AC outlet
AC power cord
Back of unit
Component
Video cable
(not supplied)
COMPONENT VIDEO
OUT
Audio/video
(not supplied)
AUDIO OUTPUT
VIDEO OUTPUT
cable
VHF/UHF
IN
VHF/UHF
OUT
RF cable
(supplied)
Connect the unit to power source.
B
Plug the end of the AC power cord into an AC outlet.
Set the VCR channel to off.
C
Before performing the following steps:
● Make sure there is no cassette inserted in the unit.
● Make sure the unit is turned on, then press VCR/
DVD on the unit or VCR on the Remote so that the
VCR indicator lights up.
A When the unit is turned off, press STOP (8) on the unit
for more than 5 seconds. “3 CH” appears on the front
display panel.
B Press CH +/– on the Remote to select “– CH” (off),
then press ENTER.
● If Plug&Play or Tuner setting has not previously been
performed, the Language Select screen appears and Plug&Play
takes place automatically.
NOTES:
● You can obtain high-quality component video pictures.
● If your TV is not stereo-capable, use the unit’s AUDIO
OUTPUT connectors to connect to an audio amplifier for
Hi-Fi stereo sound reproduction.
● To operate the unit with your TV using the Component Video
connection, set your TV to its AV mode. You can also use the
TV/VCR button on the unit’s Remote to set JVC TV to the AV
mode.
● For switching the TV’s mode, refer to the instruction manual of
your television.
● By using the component video connection, you can view the
images in the progressive mode. For switching to the
progressive mode, refer to “Scan Mode Set (DVD deck)”
(
墌 pg. 78).
To Component Video
Input connector
To 75 ohm
Terminal
TV
INITIAL SETTINGS
A
Plug & Play Set
Auto Channel Set
The Plug & Play Set simplifies installation by guiding you
through the procedures of setting the language, clock and tuner
channels – simply follow the on-screen menus that appear.
EN 15
Before starting, make sure of the following:
●
The TV aerial cable should be connected to the unit.
●
The unit’s AC power cord should be connected to an AC outlet.
●
The TV should be set to its AV mode (with AV, S-VIDEO or
Component Video connection (
channel (with RF connection
●
Slide the
TV/VCR/DVD
Turn on the unit.
A
Press POWER (1) on the unit or Remote. The Language
Select screen appears on the TV screen.
Select the language.
B
Press rt to move the
highlight bar (arrow) to the
language of your choice,
then press ENTER or e.
● The Clock Set screen appears.
墌
pg. 12, 13, 14) or VCR
墌
pg. 12)).
switch to the right.
LANGUAGE SELECT
PRESS ( , ), THEN (ENTER)
PRESS (SET UP) TO END
ENGLISH
ESPAÑOL
NOTE:
The selected language is only available on the screen for VCR deck. Set
manually the on-screen language for the DVD deck. (
墌
pg. 19)
NOTE:
If there is a power cut, or if you press POWER (1) or SET UP
while Auto Channel Set is in progress, Auto Channel Set will be
interrupted; be sure to turn off the unit power once and try again
from step A.
TTENTION
If you perform Auto Channel Set successfully during
installation, there’s no need to separately perform the
Language Select, Clock Set or Channel Set procedures, but if
adjustments become necessary, they can be performed as
follows:
● Language setting
● Tuner setting
● Clock setting
墌 pg. 18
墌 pg. 24
墌 pg. 22
Set the time.
C
Press rt to set the hour,
then press ENTER or e.
● Press and hold rt to change
the time by 30 minutes.
Set the date.
D
Press rt to set the date, then press ENTER or e.
● Press and hold rt to change the date by 15 days.
Set the year.
E
Press rt to set the year.
Start Auto Channel Set.
F
Press SET UP.
DO NOT press any button on the unit or Remote
while Auto Channel Set is in progress.
●
Receivable channels in your area are
automatically assigned to the
buttons, and non-receivable
channels are skipped.
●
When Auto Channel Set is
completed, “SCAN COMPLETED”
will appear on the TV screen. If
“SCAN COMPLETED –NO SIGNAL–
” is displayed on the TV screen, make sure that the aerial cable is
connected to the unit properly and press
unit will try Auto Channel Set again.
CH +/–
CLOCK SET
TIME DATE YEAR
: AM 1/ 1 04
PRESS ( , ), THEN (ENTER)
PRESS (SET UP) TO END
ENTER
on the Remote. The
16 EN
Monitor Set
Turn on the unit.
A
Press POWER (1).
INITIAL SETTINGS (cont.)
(DVD deck)
You can select the monitor type depending the TV used
when you play back DVD VIDEO discs recorded for
wide-screen TVs.
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
Select the DVD deck.
B
On the unit
Press VCR/DVD repeatedly so that the DVD indicator
lights up.
On the Remote
Press DVD so that the DVD indicator lights up.
Access the DVD Set Up menu screen.
C
A Press SET UP.
B Press we to select
“PICTURE”.
Select the mode.
D
Press rt to move the
highlight to “MONITOR
TYPE”, then press ENTER.
PICTURE
MONITOR TYPE
PICTURE SOURCE
SCREEN SAVER
FILE TYPE
SELECT
USE TO SELECT, USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP].
ENTER
PICTURE
MONITOR TYPE
PICTURE SOURCE
SCREEN SAVER
FILE TYPE
SELECT
USE TO SELECT, USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP].
ENTER
4:3 LB
AUTO
ON
AUDIO
4:3 LB
AUTO
ON
AUDIO
Select the mode setting.
E
Press rt to select the desired setting, then press ENTER.
Return to the normal screen.
F
Press SET UP.
EN 17
* The default setting is bold in the table below.
8 MONITOR TYPE
16:9 (Wide television conversion):
Select this when the aspect ratio of your TV is
fixed to 16:9 (wide TV). The unit automatically
adjusts the screen width of the output signal
correctly when playing back a picture whose
aspect ratio is 4:3.
4:3 LB (Letter Box conversion):
Select this when the aspect ratio of your TV is
4:3 (conventional TV). While viewing a wide
screen picture, the black bars appear on the
top and the bottom of the screen.
4:3 PS (Pan&Scan):
Select this when the aspect ratio of your TV is
4:3 (conventional TV). While viewing a wide
screen picture, the black bars do not appear;
however, the left and right edges of the
pictures will not be shown on the screen.
The following selections will be output in PAL
format when a disc recorded in PAL system is
being playback. They are only valid when multisystem television is connected.
However, these selections will not be available in
your area.
16:9 MULTI (Wide television conversion with MultiSystem):
The operation is the same as 16:9, but the
image being output will be in line with the
image format of the DVD disc being playback.
(E.g. When playing back a PAL system DVD
disc, the image output from the Audio/Video
Output will be in PAL format.)
4:3 MULTI LB (Letter Box conversion with MultiSystem):
The operation is the same as 4:3 LB, but the
image being output will be in line with the
image format of the DVD disc being playback.
4:3 MULTI PS (Pan&Scan with Multi-System):
The operation is the same as 4:3 PS, but the
image being output will be in line with the
image format of the DVD disc being playback.
Pan&Scan/Letter Box
In general, DVD VIDEO disc are produced for a wide-screen
TV with 16:9 aspect ratio.
Material with this ratio will not fit to a TV with 4:3 aspect
ratio. There are two styles to display the image, “Pan&Scan”
(PS) and “Letter Box” (LB).
Pan&Scan
The right and left side of the image are
cut off. The image fills the screen.
Letter Box
Black bands appear at the top and
bottom of the image. The image itself
appears in 16:9 aspect ratio.
18 EN
Language
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
INITIAL SETTINGS (cont.)
On-screen Language Set (VCR deck)
Use language setting only if the language has not been
set correctly by the Plug&Play setting. The default setting
is “ESPAÑOL”.
Turn on the unit.
A
Press POWER (1).
Select the VCR deck.
B
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the Remote
Press VCR so that the VCR indicator lights up.
Access the Main Menu screen.
C
Press SET UP.
Access the Initial Set screen.
D
Press rt to move the
highlight bar (arrow) to
“ADJUSTE INICIAL”, then
press ENTER or e.
MENU PRINCIPAL
ADJUSTE DE FUNCTION
ADJUSTE DE SINTONIZADOR
ADJUSTE INICIAL
Select the language.
E
Press rt to move the
highlight bar (arrow) to
“IDIOMA”, then press
ENTER or e repeatedly to
select for “INGLÉS” for
English.
Return to the normal screen.
F
Press SET UP.
ELEGIR CON ( , ) Y (ENTER)
PULSE (SET UP) P/ TERMINAR
AJUSTE INICIAL
AJUSTE DE RELOJ
IDIOMA INGLÉS
ELEGIR CON ( , ) Y (ENTER)
PULSE (SET UP) P/TERMINAR
EN 19
On-screen Language Set (DVD deck)
This DVD deck offers you the choice to view on-screen
messages in 3 different languages. You can change the
language setting manually as required. The default
language is “ENGLISH”.
Turn on the unit.
A
Press POWER (1).
Select the DVD deck.
B
On the unit
Press VCR/DVD repeatedly so that the DVD indicator
lights up.
On the Remote
Press DVD so that the DVD indicator lights up.
Access the DVD Set Up menu screen.
C
A Press SET UP.
B Press we to select
“ LANGUAGE”.
LANGUAGE
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
ENGLISH
ENGLISH
OFF
ENGLISH
SELECT
USE TO SELECT, USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP].
ENTER
Select the mode.
D
Press rt to move the
highlight to “ON SCREEN
LANGUAGE”, then press
ENTER.
Select the mode setting.
E
LANGUAGE
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
SELECT
USE TO SELECT, USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP].
ENTER
ENGLISH
ENGLISH
OFF
ENGLISH
Press rt to select the desired setting, then press ENTER.
Return to the normal screen.
F
Press SET UP.
20 EN
INITIAL SETTINGS (cont.)
Menu/Audio/Subtitle Language Set
(DVD deck only)
Some DVD discs contain the DVD menu display, audio,
subtitle in the multiple languages. With these discs, you
can set the default language as you like.
● The procedure shows how to set “MENU LANGUAGE”
on the DVD Set Up menu screen as an example.
Turn on the unit.
A
Press POWER (1).
Select the DVD deck.
B
On the unit
Press VCR/DVD repeatedly so that the DVD indicator
lights up.
On the Remote
Press DVD so that the DVD indicator lights up.
Access the DVD Set Up menu screen.
C
A Press SET UP.
B Press we to select
“ LANGUAGE”.
LANGUAGE
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
ENGLISH
ENGLISH
OFF
ENGLISH
SELECT
USE TO SELECT, USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP].
ENTER
Select the mode.
D
Press rt to move the
highlight to “MENU
LANGUAGE”, then press
ENTER.
Select the mode setting.
E
LANGUAGE
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
SELECT
USE TO SELECT, USE OK TO CONFIRM.
TO EXIT, PRESS [SET UP].
ENTER
ENGLISH
ENGLISH
OFF
ENGLISH
Press rt to select the desired setting, then press ENTER.
● See “Language Code List” (墌 pg. 21).
Return to the normal screen.
F
Press SET UP.
NOTE:
When the selected language is not available on the disc, the
disc’s default menu language is played back.
Language Code List
EN 21
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
GN
GU
HA
HI
HR
HU
HY
IA
IE
Afar
Abkhazian
Afrikaans
Ameharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
IK
IN
IS
IW
JI
JW
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NL
NO
OC
OM
OR
PA
PL
PS
PT
QU
RM
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean (KOR)
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay (MAY)
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Wolof
Xhosa
Yoruba
Zulu
22 EN
Clock Set
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
INITIAL SETTINGS (cont.)
Perform clock setting only if the clock has not been set
correctly by the Plug&Play setting.
Turn on the unit.
A
Press POWER (1).
Select the VCR deck.
B
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the Remote
Press VCR so that the VCR indicator lights up.
Access the Main Menu screen.
C
Press SET UP.
Access the Initial Set screen.
D
Press rt to move the
highlight bar (arrow) to
“INITIAL SET”, then press
ENTER or e.
Access the Clock Set screen.
E
Press rt to move the
highlight bar (arrow) to
“CLOCK SET”, then press
ENTER or e.
EN 23
Set the time.
F
Press rt to set the hour,
then press ENTER or e.
● Press and hold rt to change
the time by 30 minutes.
Set the date.
G
Press rt to set the date, then press ENTER or e.
● Press and hold rt to change the date by 15 days.
Set the year.
H
Press rt to set the year.
Start clock.
I
Press SET UP and normal screen appears.
To make corrections any time during the process
Press ENTER or e repeatedly until the item you want to
change blinks, then press rt.
CLOCK SET
TIME DATE YEAR
– –:– –AM 1/ 1 04
PRESS ( , ), THEN (ENTER)
PRESS (SET UP) TO END
24 EN
Tuner Set
INITIAL SETTINGS (cont.)
Auto Channel Set
Perform Auto Channel Set only if channels have not been set
correctly by the Plug&Play setting.
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
INFORMATION
The unit selects the correct band (TV or CATV) automatically
during Auto Channel Set. The selected band will be
displayed on the right side of “BAND” on the Tuner Set
screen.
Turn on the unit.
A
Press POWER (1).
Select the VCR deck.
B
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the Remote
Press VCR so that the VCR indicator lights up.
Access the Main Menu screen.
C
Press SET UP.
Access the Tuner Set screen.
D
Press rt to move the
highlight bar (arrow) to
“TUNER SET”, then press
ENTER or e.
Perform Auto Channel Set.
E
Press rt to move the
highlight bar (arrow) to
“AUTO CHANNEL SET”, then
press ENTER or e. You can
automatically set the
receivable channels in your
area in the order of their
frequencies.
● When Auto Channel Set is
complete, “SCAN
COMPLETED” appears on the
TV screen.
● If the scan was unsuccessful,
“SCAN COMPLETED–NO
SIGNAL–” appears on screen.
Check the connections and start
again.
Return to the normal screen.
F
Press SET UP.
EN 25
Manual Channel Set
You can add the channels you want or delete the channels you
do not want manually.
Turn on the unit.
A
Press POWER (1).
Select the VCR deck.
B
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the Remote
Press VCR so that the VCR indicator lights up.
Access the Main Menu screen.
C
Press SET UP.
Access the Tuner Set screen.
D
Press rt to move the highlight bar (arrow) to “TUNER
SET”, then press ENTER or e.
Access the Manual Channel Set screen.
E
Press rt to move the
highlight bar (arrow) to
“MANUAL CHANNEL SET”,
then press ENTER or e.
Add or skip the desired channels.
F
To add channels
A Press the number keys to
input a channel number you
want to add.
B Press ENTER or e to set to
“ADD”.
C Repeat A to B to add other
channels.
To skip channels
A Press rt or the number keys to select a channel
number you want to skip.
B Press ENTER or e to set to “SKIP”.
C Repeat A and B to skip other channels.
Return to the normal screen.
G
Press SET UP.
26 EN
Basic Playback
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
OPERATIONS ON VCR DECK
Load a cassette.
A
Make sure the window side is up, the rear label side is
facing you and the arrow on the front of the cassette is
pointed toward the unit.
● Do not apply too much pressure when inserting.
● If the record safety tab has been removed, playback begins
automatically. Although the DVD deck is selected, the VCR
deck is selected automatically if the DVD deck is in stop
mode.
● The unit’s power comes on automatically and the counter is
reset to 0:00:00.
Select the VCR deck.
B
On the unit
Press VCR/DVD repeatedly so that the VCR indicator
lights up.
On the Remote
Press VCR so that the VCR indicator lights up.
Find the program start point.
C
If the tape is advanced past the start point, press REW
(3). To go forward, press FF (5).
Clean the video heads using a dry cleaning
cassette — ECL-3F — when:
● Rough, poor picture appears while a tape is played back.
● The picture is unclear or no picture appears.
● “USE CLEANING CASSETTE” appears on the screen (only
with “SUPERIMPOSE” set to “ON”). (
墌 pg. 73)
NOTE:
The heads get dirty in the following cases:
● in an environment prone to extreme temperature or
humidity
● in a dusty environment
● flaw, dirt or mold on video tapes
● continuous usage for a long time
Start playback.
D
Press PLAY (4).
Stop playback.
E
Press STOP (8). Then press EJECT (x) on the VCR deck
to remove the cassette.
Usable cassettes
Full-Size VHS
T-30 (ST-30**)
T-60 (ST-60**)
T90
T-120 (ST-120**)
T-160 (ST-160**)
ST-210**
Compact VHS*
TC-20 (ST-C20**)
TC-30 (ST-C30**)
TC-40 (ST-C40**)
* Compact VHS camcorder recordings can be played on
this unit. Simply place the recorded cassette into a VHS
Cassette Adapter and it can be used just like any full-sized
VHS cassette.
** This unit can record on regular VHS and Super VHS
cassettes. However, it will record regular VHS signals
only.
• S-VHS recording is not possible with this unit.
● This unit is equipped with SQPB (S-VHS QUASI
PLAYBACK) that lets you watch tapes recorded in the SVHS format and the SP mode with regular VHS
resolution.
• SQPB does not deliver Super VHS resolution.
Playback Features
EN 27
Still Picture/Frame-By-Frame
Playback
● Turn on the TV and select the VCR channel (or AV
mode).
● Slide the TV/VCR/DVD switch to the right.
CH +/–
1 Pause during playback.
Press PAUSE (9).
● If there is vertical jitter, press CH +/– on the Remote or on the
unit to correct the picture.
2 Activate frame-by-frame playback.
Press PAUSE (9) to advance a still picture.
Slow Motion
1 Pause during playback.
Press PAUSE (9).
2 Activate slow motion playback.
Press and hold PAUSE (9) for 2 seconds, then release.
Press PAUSE (9) and release again to return to still
picture.
NOTE:
During slow motion playback, some noise may appear on the
TV screen. Press CH + or – on the Remote or on the unit to
eliminate the noises.
Variable Speed Search
During playback, press FF (5) for forward variable
speed search, or REW (3) for reverse variable speed
search.
● The speed changes for each direction by pressing REW (3)
and FF (5) repeatedly.
When pressing FF (5):
(SP): +5x{+7x
(EP): +11x{+21x
When pressing REW (3):
Once REW (3) is pressed, reverse search starts in –1x
normal playback speed. After this process, each press of REW
(3) changes the search speed between –5x and –7x in SP
mode, –11x and –21x in EP mode.
(SP): –1x]–5x{–7x
(EP): –1x]–11x{–21x
ATTENTION
In the search, still, slow-motion or frame-by-frame playback
mode,
● the picture will be distorted.
● the noise bars will appear.
● there may be a loss of color.
● you cannot hear the sound.
To resume normal playback, press PLAY (4).
Loading...