JVC HR-XV1MS Service Manual

SERVICE MANUAL

LECTEUR DVD Hi-Fi VIDÉO MAGNÉTOSCOPE

HR-XV1MS

PAL SECAM

DIGITAL VIDEO

Regarding service information other than these sections, refer to the service manual No. 82927 (HR-XV1EU-C). Also, be sure to note important safety precautions provided in the service manual.

Caractéristiques techniques

GENERAL

Fonctionne sur courant: AC 230V 50Hz Consommation électrique: marche: 22W

veille: 5W Poids: 4.5 kg Dimensions: largeur: 430 mm

Hauteur: 99 mm

profondeur: 310.5 mm Niveau d’entrée: Prise SCART: VIDEO: 1 Vp-p, 75 Ω

AUDIO: 500 mV , 50 kΩ

Audio IN jack: 500 mV, 50 k Ω Niveau de sortie: Prise SCART: VIDEO: 1 Vp-p, 75 Ω

AUDIO: 500 mV , 1 kΩ

Audio OUT jack: 500 mV, 1 kΩ Hi-Fi Distorsion de fréquence:20Hz to 20,000Hz Hi-Fi Gamme d’amplification: More than 75dB

Magnétoscope

Signal couleur: P AL et SECAM Lecture NTSC Tête vidéo: 4 têtes rotatives Piste audio: Son Hi-Fi - 2 pistes/son mono - 1 piste Couverture des canaux: 2-12, X, Y, Z, S1-S41, 21-69 Durée rembobinage rapide: Environ 1 minute 48 secondes

(avec une cassette E-180) (à + 25˚C)

Lecteur DVD

Système de signal: PAL Disque compatibles: DVD (12cm, 8cm), CD (12cm, 8cm) Caract

éristiques audio: DVD: 4Hz - 22KHz Distorsion de fréquence: CD: 4Hz - 20KHz T

aurapport signal/bruit 90dB Distorsion harmonique: 0.1% scintillement et pleurage: En dessous des seuils de mesure Gamme d’amplification: 90dB sortie:

Micro:

CCESSOIRES: Télécommande x 1

Audio: (RCA) 500 mV , 1Kohm Digital Audio: 0.5Vp-p/75 ohm CD: longueur d’onde: 775 - 805 nm

Sortie maximum: 0.5 mW

DVD: longueur d’ondes: 640 - 660 nm

Sortie maximum: 1.0 mW

Câble coaxial 75 ohm x 1 Câble Scart x 1 Pile (UM-3) x 2

This service manual is printed on 100% recycled paper.

HR-XV1MS V14PV1

No.82943

August 2002

DIFFERENT TABLE .............................................................................................................................................................................................. 1 only

WHEN REPLACING EEPROM(MEMORY) IC ...........................................................................................................................................

2. CHARTS AND DIAGRAMS (2-1 to 2-13)

Y/C/AUDIO/H.AMP SCHEMATIC DIAGRAM.........................................................................................................................................2-1

MICOM SCHEMATIC DIAGRAM........................................................................................................................................................... 2-3

TUNER/JACK SCHEMATIC DIAGRAM................................................................................................................................................. 2-5

SUB MICOM/OSD/VPS SCHEMATIC DIAGRAM.................................................................................................................................. 2-7

PRINTED CIRCUIT BOARD VCR ......................................................................................................................................................... 2-9

3. PARTS LIST (3-1 to 3-7)

3.1 PACKING AND ACCESSOR Y ASSEMBL Y <M1> ................................................................................................................................. 3-1

3.2 ELECTRICAL PART LIST

VCR BOARD ASSEMBLY<03>................................................................................................................................................................ 3-2

4. REFERENCE (4-1 to 4-6)

GENERAL SPECIFICATIONS ............................................................................................................................................................... 4-1

The following table indicates main different points between models HR-XV1EU-C and HR-XV1MS.

ITEM

VIDEO SYSTEM PAL PAL/SECAM/MESECAM RF OUT USED NOT USED VPS USED NOT USED 21 PIN CABLE OPTIONAL PROVIDED

The following table indicates different parts number between models HR-XV1EU-C and HR-XV1MS.

PACKING AND ACCESSOR Y ASSEMBLY<M1>

PACKING AND ACCESSORY ASSEMBLY<M1> is indicated on the parts list.

FINAL ASSEMBL Y<M2>

REF

!601 CABINET ,FRONT ASSY X-A2A735B720 X-A2A779D720

VCR BOARD ASSEMBLY<03>

ITEM

NO.

608 CABINET ,FRONT X-701WPJB706 X-701WPJ1135

REF

ITEM

NO.

PW1 VCR BOARD ASSY X-A2A735B010 X-A2A779D010B

MODEL

HR-XV1EU-C

HR-XV1EU-C HR-XV1MS

HR-XV1MS

1 only

WHEN REPLACING EEPROM (MEMORY) IC

If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1.

NOTE: No need setting for after INI FD.

INI +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F B0 --- --- --- --- --- --- --- --- --- 8B C9 D2 71 62 76 08

C0 B2 17 90 50 60 F1 54 51 51 51 B2 9F D0 D9 64 2A 08 02 FF 40 00 71 9F 82 02 42 35 63 5B E0

76 5F 08 F0 0A FB 5F 08 F0 05 F2 5F 09 F0 05 F3

F0 16 2F 9F 42 42 80 3D 68 08 89 04 3A CC --- --- ---

[TABLE 1]

Turn on the POWER.

1. Press both CH UP button on the set and the FF button on the set for more than 2 seconds.

2. ADDRESS and DATA will appear on FIP as Fig 1. ADDRESS is now selected and should “blink”. Using the SET + or - button on the remote,

3. step through the ADDRESS until required ADDRESS to be changed is reached. Press OK to select DATA. When DATA is selected, it will “blink”.

4. Again, step through the DATA using SET + or - button until required DATA value has been

5. selected. Pressing OK will take you back to ADDRESS for further selection if necessary.

6. Repeat steps 3 to 6 until all data has been checked.

7. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY

8. MODE) to finish DATA input.

The unit will now have the correct DATA for the new MEMORY IC.

8E 04 FA

ADDRESS DATA

Fig. 1

+ 8 hidden pages

JVC HR-XV1MS Service Manual

TABLE OF CONTENTS

WHEN REPLACING EEPROM (MEMORY) IC