JVC GR-367, GR-365, GR-160 User's Guide

ENGLISH
DIGIT AL VIDEO CAMERA
GR-DVL767 GR-DVL367 GR-DVL365 GR-DVL160
Please visit our Homepage on the World Wide Web and answer our Consumer Survey (in English only):
http://www.jvc-victor.co.jp/english/index-e.html
For Accessories:
http://www.jvc-victor.co.jp/english/accessory/
CONTENTS
AUTOMATIC DEMONSTRATION
GETTING STARTED
TAPE RECORDING & PLAYBACK
TAPE RECORDING ........................
TAPE PLAYBACK ..........................
MEMORY CARD RECORDING & PLAYBACK
MEMORY CARD RECORDING .........
MEMORY CARD PLAYBACK............
ADVANCED FEATURES ....................
ADVANCED FEATURES
FOR RECORDING ...........................
USING MENUS FOR
DETAILED ADJUSTMENT ..............
DUBBING .....................................
USING THE REMOTE CONTROL UNIT
SYSTEM CONNECTIONS .........................
REFERENCES
DETAILS .............................................
TROUBLESHOOTING ......................
USER MAINTENANCE ............................
CAUTIONS ....................................
SPECIFICATIONS ...........................
INDEX .........................................
TERMS ...............................
66 –
7 – 14
16 – 20 21 – 24
26 – 27 28 – 29 30 – 36
38 – 45
46 – 51 52 – 53
...
54 – 64
Back Cover
68 – 73
75 – 77 78 – 79 80 – 86
87 –
Back Cover
6
65
67
74
The camcorder illustrations appearing in this instruction manual are of the GR-DVL767.
Memory card recording features are available on GR-DVL767,DVL367 and GR-DVL365
INSTRUCTIONS
LYT0910-001B
EN
2
EN
Dear Customer,
Thank you for purchasing this digital video camera. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of this product.
Using This Instruction Manual
•All major sections and subsections are listed in the Table Of Contents on the cover page.
•Notes appear after most subsections. Be sure to read these as well.
•Basic and advanced features/operation are separated for easier reference.
It is recommended that you . . .
..... refer to the Index ( pgs. 80 – 86) and familiarize yourself with button locations, etc. before use.
..... read thoroughly the Safety Precautions. They contain extremely important information regarding the safe use
of this product.
You are recommended to carefully read the cautions on pages 75 through 77 before use.
SAFETY PRECAUTIONS
IMPORT ANT (for owners in the U.K.)
Connection to the mains supply in the United Kingdom. DO NOT cut off the mains plug from this equipment.
If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.
BE SURE to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover.
If nonetheless the mains plug is cut off be sure to remove the fuse and dispose of the plug immediately, to avoid possible shock hazard by inadvertent connection to the mains supply. If this product is not supplied fitted with a mains plug then follow the instructions given below: DO NOT make any connection to the Larger Terminal coded E or Green. The wires in the mains lead are coloured in accordance with the following code:
Blue to N (Neutral) or Black Brown to L (Live) or Red
If these colours do not correspond with the terminal identifications of your plug, connect as follows: Blue wire to terminal coded N (Neutral) or coloured black. Brown wire to terminal coded L (Live) or coloured Red. If in doubt — consult a competent electrician.
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTIONS:
To prevent shock, do not open the cabinet. No user serviceable parts inside. Refer servicing to qualified personnel.
When you are not using the AC Adapter for a long period of time, it is recommended that you disconnect the power cord from AC outlet.
NOTES:
The rating plate (serial number plate) and safety caution are on the bottom and/or the back of the main unit.
The rating information and safety caution of the AC Adapter are on its upper and lower sides.
CAUTION:
To avoid electric shock or damage to the unit, first firmly insert the small end of the power cord into the AC Adapter until it is no longer wobbly, and then plug the larger end of the power cord into an AC outlet.
EN
3
CAUTIONS:
This camcorder is designed to be used with PAL-type colour television signals. It cannot be used for playback with a television of a different standard. However, live recording and LCD monitor/viewfinder playback are possible anywhere.
Use the JVC BN-V408U/V416U/V428U battery packs and, to recharge them or to supply power to the camcorder from an AC outlet, use the provided multi-voltage AC Adapter and Power Cord. (An appropriate conversion adapter may be necessary to accommodate different designs of AC outlets in different countries.)
When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear).
Do not block the ventilation holes. (If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)
No naked flame sources, such as lighted candles, should be placed on the apparatus. When discarding batteries, environmental problems must be considered and the local rules or laws
governing the disposal of these batteries must be followed strictly. The apparatus shall not be exposed to dripping or splashing. Do not use this equipment in a bathroom or places with water.
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups etc.) on top of this unit. (If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
SOME DO’S AND DON’TS ON THE SAFE USE OF EQUIPMENT
This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
DO read the operating instructions before you attempt to use the equipment. DO ensure that all electrical connections (including the mains plug, extension leads and interconnections
between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment. DO be careful with glass panels or doors on equipment. DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in
any way switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages. DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for
unattended operation or has a standby mode. Switch off using the switch on the equipment and make sure that your family knows how to do this. Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of
road safety. It is illegal to watch television whilst driving.
DON’T listen to headphones at high volume, as such use can permanently damage your hearing. DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings. Overheating will
cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws to ensure complete safety always fit the
manufacturers approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture. ABOVE ALL
NEVER let anyone especially children push anything into holes, slots or any other opening in the case this
could result in a fatal electrical shock;
NEVER guess or take chances with electrical equipment of any kind it is better to be safe than sorry!
4
EN
SAFETY PRECAUTIONS
Do not point the lens or the viewfinder directly into the sun. This can cause eye injuries, as well as lead to the malfunctioning of internal circuitry. There is also a risk of fire or electric shock.
CAUTION!
The following notes concern possible physical damage to the camcorder and to the user. When carrying, be sure to always securely attach and use the provided shoulder strap. Carrying or holding the
camcorder by the viewfinder and/or the LCD monitor can result in dropping the unit, or in a malfunction. Take care not to get your finger caught in the cassette holder cover. Do not let children operate the camcorder, as
they are particularly susceptible to this type of injury. Do not use a tripod on unsteady or unlevel surfaces. It could tip over, causing serious damage to the camcorder.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.) to the camcorder and leaving the unit on top of the TV is not recommended, as tripping on the cables will cause the camcorder to fall, resulting in damage.
This camcorder is designed exclusively for the digital video cassette, SD Memory Card and
MultiMediaCard. Only cassettes marked
can be used with this unit.
and memory cards* marked or
Before recording an important scene . . .
.... make sure you only use cassettes with the Mini DV mark .
.... make sure you only use memory cards* with the mark or .
.... remember that this camcorder is not compatible with other digital video formats.
.... remember that this camcorder is intended for private consumer use only. Any commercial use without
proper permission is prohibited. (Even if you record an event such as a show, performance or exhibition for personal enjoyment, it is strongly recommended that you obtain permission beforehand.)
* Memory cards can be used with GR-DVL767/DVL367/DVL365 only.
PROVIDED ACCESSORIES
EN
5
or
AC Adapter AP-V10EG, AP-V11EG or AP-V12EG
Shoulder Strap
USB Cable (GR-DVL767/ DVL367/DVL365 only)
Lens hood (Already attached to the camcorder; GR-DVL767 only)
Cable Adapter
Memory Card 8 MB (GR-DVL767/DVL367/ DVL365 only) (Already inserted in the camcorder)
Core Filter x 1 (for optional S-Video cable
pg. 6 for
attachment)
Battery Pack BN-V408U
or
Lens Cap (See below for attachment)
Power Cord
Remote Control Unit RM-V717U
Audio/Video Cable (ø3.5 mini-plug to RCA plug)
Core Filter x 1 (for PC Connection cable provided with optional HS-V16KITE software; GR-DVL160 only for attachment)
pg. 6
AAA (R03) Battery x 2 (for remote control unit)
CD-ROM (GR-DVL767/DVL367/ DVL365 only)
Editing Cable GR-DVL160:
One plug has 3 rings around the pin, and the other has 1 ring around the pin.
GR-DVL767DVL367/ DVL365: Both plugs have 1 ring around the pin.
NOTE:
In order to maintain optimum performance of the camcorder, provided cables may be equipped with one or more core filter. If a cable has only one core filter, the end that is closest to the filter should be connected to the camcorder.
How To Attach The Lens Cap
To protect the lens, attach the provided lens cap to the camcorder as shown in the illustration.
NOTE:
To confirm the lens cap is on correctly make sure the cap is flush to the camera.
1 2 3
For GR-DVL767 Owners:
The lens cap can be attached only when the lens hood is attached to the camcorder.
6
MODEDEMO –ONOFF
EN
How To Attach The Core Filter
Attach the Core Filter(s) (if provided with your model pg. 5) to an optional cable(s). The Core Filter reduces interference.
1
Stopper
Release the stoppers on both ends of the Core Filter.
When connecting cables, attach the end with the Core Filter to the camcorder.
23
Run the cable through the Core Filter, leaving approx. 3 cm of cable between the cable plug and the Core Filter. Wind the cable once around the outside of the Core Filter as shown in the illustration.
Wind the cable so that it is not slack.
NOTE:
Take care not to damage the cable.
3 cm
Wind once
AUTOMATIC DEMONSTRATION
Automatic Demonstration takes place when “DEMO
MODE is set to ON (factory-preset).
Automatic Demonstration starts when there is no operation for
about 3 minutes after the Power Switch is set to
M
ANUAL
and no cassette is in the camcorder.
Performing any operation during the demonstration stops the
demonstration temporarily. If no operation is performed for more than 3 minutes after that, the demonstration will resume.
“DEMO MODE remains ON even if the camcorder power is
turned off.
To cancel Automatic Demonstration:
M
1. Set the Power Switch to
ANUAL
while pressing down the
Lock Button located on the switch and press the MENU/
BRIGHT wheel in. The Menu Screen appears.
2. Rotate the MENU/BRIGHT wheel to select SYSTEM
and press it. The SYSTEM Menu appears.
3. Rotate the MENU/BRIGHT wheel to select “DEMO MODE and press it. The Sub Menu appears.
4. Rotate the MENU/BRIGHT wheel to select OFF and press it.
5. Rotate the MENU/BRIGHT wheel to select RETURN”,
and press it twice. The normal screen appears.
AUTO
or
Close the Core Filter until it clicks shut.
MENU/BRIGHT Wheel
Power Switch
Lock Button
Sub Menu
NOTE:
If you do not detach the Lens Cap, you cannot see the actual changes of the Automatic Demonstration activated on the LCD monitor or viewfinder.
GR-DVL767/DVL367/DVL365 only
GETTING STARTED
EN
GETTING STARTED
CONTENTS
Power.................................................. 8 – 9
Grip Adjustment ......................................... 10
Viewfinder Adjustment.................................. 10
Shoulder Strap Attachment ............................. 10
Tripod Mounting .......................................... 10
Date/Time Settings...................................... 11
Loading/Unloading A Cassette ......................... 12
Recording Mode Setting ................................. 13
Loading A Memory Card
(GR-DVL767/DVL367/DVL365 only) ........................ 14
Picture Quality/Image Size Setting
(GR-DVL767/DVL367/DVL365 only) ........................ 14
7
8
EN
BATT. RELEASE Button
1
GETTING STARTED
(cont.)
Power
This camcorders 2-way power supply system lets you choose the most appropriate source of power. Do not use provided power supply units with other equipment.
Battery pack
AC Adapter
5
To AC outlet
6
3
2
Power Switch
CHARGE Lamp
4
To DC connector
CHARGING THE BATTERY PACK
1 Tilt the viewfinder upward 1. With the arrow on
the battery pack pointing downward, push the battery pack slightly against the battery pack mount 2, then slide down the battery pack until it locks in place 3.
2 Set the Power Switch to “OFF. Connect the AC
Adapter to the camcorder 4, then connect the Power Cord to the AC Adapter 5.
3 Plug the Power Cord into an AC outlet 6.
The CHARGE lamp on the camcorder blinks to indicate charging has started.
4 When the CHARGE lamp stops blinking but stays
lit, charging is finished. Unplug the Power cord from the AC outlet. Disconnect the AC Adapter from the camcorder.
To Detach The Battery Pack . . .
.....Press BATT. RELEASE and pull out the battery
pack.
NOTES:
If the protective cap is attached to the battery pack, remove it first.
During charging, the camcorder cannot be operated.
Charging is not possible if the wrong type of battery is
used.
When charging the battery pack for the first time or after a long storage period, the CHARGE lamp may not light. In this case, remove the battery pack from the camcorder, then try charging again.
If the battery operation time remains extremely short even after having been fully charged, the battery is worn out and needs to be replaced. Please purchase a new one.
Using the optional AA-V40EK AC Power Adapter/ Charger, you can charge the BN-V408U/V416U/V428U battery pack without the camcorder. However , it cannot be used as an AC adapter.
Battery pack
BN-V408U BN-V416U (optional) BN-V428U (optional)
Charging time
approx. 1 hr. 30 min. approx. 3 hrs. approx. 5 hrs.
For other notes, pg. 67
EN
9
ATTENTION
Before detaching the power source, make sure that the camcorders power is turned off. Failure to do so can result in a camcorder malfunction.
NOTES:
Recording time is reduced significantly under the following conditions:
Zoom or Record-Standby mode is engaged
repeatedly.
The LCD monitor is used repeatedly.
The playback mode is engaged repeatedly.
Before extended use, it is recommended that you prepare enough battery packs to cover 3 times the planned shooting time.
INFORMATION
The extended-use battery pack kit is a set composed of a battery pack and AC Power Adapter/Charger: VU-V840 KIT: BN-V840U battery pack & AA-V15EK
AC Power Adapter/Charger
VU-V856 KIT: BN-V856U battery pack & AA-V80EK
AC Power Adapter/Charger Read the kit's instruction manual before using. Also, by using the optional JVC VC-VBN856U DC Cord, it will be possible to connect BN-V840U or BN­V856U battery packs to the camcorder and supply power directly to the camcorder.
USING THE BATTERY PACK
Perform step 1 of CHARGING THE BATTER Y PACK ( pg. 8).
Approximate recording time
<
GR-DVL367/DVL365/DVL160
Battery pack
BN-V408U
BN-V416U (optional)
BN-V428U (optional)
BN-V840U (optional)
BN-V856U (optional)
LCD monitor on
1 hr.
(35 min.)
2 hrs.
(1 hr. 10 min.)
3 hrs. 30 min.
(2 hrs.)
5 hrs.
(2 hrs. 50 min.)
7 hrs.
(4 hrs.)
( ) : when the video light is on
Approximate recording time
<
GR-DVL767
Battery pack
BN-V408U
BN-V416U (optional)
BN-V428U (optional)
BN-V840U (optional)
BN-V856U (optional)
>
LCD monitor on
55 min.
(35 min.)
1 hr. 55min.
(1 hr. 15 min.)
3 hrs. 25 min.
(2 hrs. 15 min.)
4 hrs. 25 min.
(2 hrs. 55 min.)
6 hrs. 40 min.
(4 hrs. 15 min.)
( ) : when the video light is on
>
Viewfinder on
1 hr. 15 min.
2 hrs. 30 min. (1 hr. 20 min.)
4 hrs. 20 min.
(2 hrs. 20 min.)
6 hrs. 10 min.
(3 hrs. 20 min.)
8 hrs. 40 min.
(4 hrs. 40 min.)
Viewfinder on
1 hr. 10 min.
2 hrs. 25 min. (1 hr. 30 min.)
4 hrs. 20 min.
(2 hrs. 40 min.)
5 hrs. 40 min.
(3 hrs. 30 min.)
8 hrs. 30 min.
(5 hrs. 5 min.)
(40 min.)
(45 min.)
To AC outlet
AC Adapter
To DC connector
USING AC POWER
Use the AC Adapter (connect as shown in the illustration).
NOTES:
The provided AC Adapter features automatic voltage selection in the AC range from 110 V to 240 V.
For other notes, pg. 67.
10
EN
GETTING STARTED
(cont.)
Power Zoom Lever
Recording Start/Stop button
PAUSE
Power Switch
Dioptre Adjustment Control
Grip Adjustment
1 Separate the Velcro strip. 2 Pass your right hand through the loop and grasp
the grip.
3 Adjust your thumb and fingers through the grip, to
easily operate the Recording Start/Stop button and Power Switch and Power Zoom Lever. Be sure to fasten the Velcro strip to your preference.
Viewfinder Adjustment
or
MANUAL
1 Set the Power Switch to “
while pressing down the Lock Button located on the switch.
AUTO
2 Turn the Dioptre Adjustment Control until the
indications in the viewfinder are clearly focused.
2
1
Shoulder Strap Attachment
1 Make sure the battery pack is removed. Following
the illustration, thread the strap through the eyelet 1, then fold it back and thread it through the buckle 2. Repeat the procedure to attach the other end of the strap to the other eyelet 3 located under the Grip Strap . Confirm the strap is not twisted.
3
Tripod Mounting
CAUTION
When attaching the camcorder to a tripod, extend its legs to stabilise the camcorder. It is not advised to use small sized tripods. This may cause damage to the unit by falling over.
1 To attach the camcorder to a tripod, align the
direction stud and screw to the mounting socket and stud hole on the camcorder. Then tighten the screw clockwise. Some tripods are not equipped with studs.
MENU/BRIGHT Wheel
Power Switch
Lock Button
Display
FADER
/ W I P E
AM AEPROGR
EXPOSURE
AN E
C
W. BAL
ACAMER
LMANUA MSYSTE AYDISPL
DSC END
RE NEON SC
IMETDAT E / T I ME CODE
CLOCK
ADJ .
Power Lamp
OF
F
LCD / TV
UAOT
– FFO
12 ..02
52
1730 :
GR-DVL767/DVL367/ DVL365 only
DISPLAY Menu
EN
11
Date/Time Settings
The date/time is recorded onto the tape at all times, but its display can be turned on or off during playback ( pg. 50, 51).
M
1 Set the Power Switch to
ANUAL
while pressing down the Lock Button located on the switch. The power lamp lights and the camcorder is turned on.
2 Press the MENU/BRIGHT wheel in to access the
Menu Screen.
3 Rotate the MENU/BRIGHT wheel to select
DISPLAY. Press it and the DISPLAY Menu appears.
4 Rotate the MENU/BRIGHT wheel to select
CLOCK ADJ.. Press it and day is highlighted. Rotate the MENU/BRIGHT wheel to input the day. Press it. Repeat to input the month, year, hour and minute. Rotate the MENU/BRIGHT wheel to select RETURN, and press it twice. The Menu Screen closes.
NOTE:
Even if you select CLOCK ADJ., if the parameter is not highlighted the camcorders internal clock continues to operate. Once you move the highlight bar to the first date/ time parameter (day), the clock stops. When you finish setting the minute and press the MENU/BRIGHT wheel in, the date and time begin operation from the date and time you just set.
CLOCK ADJ .
NRETUR
12 ..02
52
1730:
12
EN
GETTING STARTED
(cont.)
Erase protection tab*
Make sure the window side is facing out.
Cassette holder
OPEN/EJECT Switch
PUSH HERE
Cassette holder cover
* To Protect Valuable Recordings . . .
....
slide the erase protection tab on the back of the tape in the direction of “SAVE. This prevents the tape from being recorded over. To record on this tape, slide the tab back to “REC” before loading it.
Be sure to press only the section labeled “PUSH HERE to close the cassette holder; touching other parts may cause your finger to get caught in the cassette holder, resulting in injury or product damage.
Loading/Unloading A Cassette
The camcorder needs to be powered up to load or eject a cassette.
1 Slide and hold OPEN/EJECT in the direction of
the arrow then pull the cassette holder cover open until it locks. The cassette holder opens automatically.
Do not touch internal components.
2 Insert or remove a tape and press PUSH HERE
to close the cassette holder.
Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely before closing the cassette holder cover.
When the batterys charge is low, you may not be
able to close the cassette holder cover. Do not apply force. Replace the battery with a fully charged one before continuing.
3 Close the cassette holder cover firmly until it
locks into place.
Approximate recording time
Tape
30 min. 30 min. 45 min. 60 min. 60 min. 90 min. 80 min. 80 min. 120 min.
Recording mode
SP LP
NOTES:
It takes a few seconds for the cassette holder to open. Do not apply force.
If you wait a few seconds and the cassette holder does not open, close the cassette holder cover and try again. If the
cassette holder still does not open, turn the camcorder off then on again.
If the tape does not load properly, open the cassette holder cover fully and remove the cassette. A few minutes later, insert it again.
When the camcorder is suddenly moved from a cold place to a warm environment, wait a short time before opening the cassette holder cover.
Closing the cassette holder cover before the cassette holder comes out may cause damage to the camcorder.
Even when the camcorder is switched off, a cassette can be loaded or unloaded. After the cassette holder is closed
with the camcorder switched off, however, it may not recede. It is recommended to turn the power on before loading or unloading.
When resuming recording, once you open the cassette holder cover a blank portion will be recorded on the tape or a previously recorded scene will be erased (recorded over) regardless of whether the cassette holder came out or not. See page 20 for information about recording from the middle of a tape.
Loosen the Grip Strap if it appears to interfere with the cassette holder cover operation (
pg. 10).
MENU/BRIGHT Wheel
Power Lamp
Power Switch
Lock Button
Display
SPREC MODE
LP
GR-DVL767/DVL367/DVL365 only
Menu Screen
Sub Menu
EN
13
Recording Mode Setting
Set the tape recording mode depending on your preference.
M
1 Set the Power Switch to
down the Lock Button located on the switch. The power lamp lights and the camcorder is turned on.
ANUAL
while pressing
2 Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
3 Rotate the MENU/BRIGHT wheel to select
CAMERA and press it. The CAMERA Menu appears.
4 Rotate the MENU/BRIGHT wheel to select “REC
MODE and press it. The Sub Menu appears. Select SP or LP by rotating the MENU/BRIGHT wheel and press it. Rotate the MENU/BRIGHT wheel to select RETURN, and press it twice. The Menu Screen closes.
Audio Dubbing ( pg. 63) and Insert Editing ( pg. 64) are possible on tapes recorded in the SP mode.
•“LP (Long Play) is more economical, providing
1.5 times the recording time.
NOTES:
If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.
It is recommended that tapes recorded in the LP mode
on this camcorder be played back on this camcorder.
During playback of a tape recorded on another
camcorder, blocks of noise may appear or there may be momentary pauses in the sound.
14
EN
Label
Clipped edge
Memory card
Card Cover
MENU/BRIGHT Wheel
Lock Button
Power Lamp
GETTING STARTED
Power Switch
Display
TYQUAL I
IMAGE SI ZE––
REC S E L EC T
NRETUR
(cont.)
FINE
021X7486
Loading A Memory Card
(GR-DVL767/DVL367/DVL365 only)
The provided memory card is already inserted in the camcorder when you receive the camcorder.
1 Make sure the camcorders power is off. 2 Press PUSH OPEN and open the LCD monitor,
then open the card cover (MEMORY CARD).
3 Insert the memory card clipped edge first.
Do not touch the terminal on the reverse side of the label.
4 To close the card cover, push it until you hear a
click.
To Unload A Memory Card . . .
..... in step 3 push the memory card, which then
comes out of the camcorder automatically. Pull it out and close the card cover.
NOTES:
Be sure to use only SD Memory Cards marked
or MultiMediaCards marked
“ “
Some brands of memory cards are not compatible with
this camcorder. Before purchasing a memory card , consult its manufacturer or dealer.
Before using a new memory card, it is necessary to
FORMAT the card.
Do not insert/remove the memory card while the camcorder is turned on, as this may cause the memory card to be corrupted or cause the camcorder to become unable to recognize whether or not the card is installed.
.
pg. 36.
ATTENTION
Picture Quality/Image Size Setting
(GR-DVL767/DVL367/DVL365 only)
The Picture Quality/Image Size can be selected to best match your needs. Refer to the chart on page 27 for your selection.
1 Set the VIDEO/MEMORY Switch to “MEMORY,
then set the Power Switch to down the Lock Button located on the switch. The power lamp lights and the camcorder turns on.
M
ANUAL
while pressing
2 Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
3 Rotate the MENU/BRIGHT wheel to select
DSC and press it. The DSC Menu appears.
4 Rotate the MENU/BRIGHT wheel to select
QUALITY and press it. The Sub Menu appears. Rotate the MENU/BRIGHT wheel to select the desired mode and press it.
5 Rotate the MENU/BRIGHT wheel to select
IMAGE SIZE and press it. The Sub Menu appears. Rotate the MENU/BRIGHT wheel to select the desired mode and press it.
6 Rotate the MENU/BRIGHT wheel to select
RETURN, and press it twice. The Menu Screen closes.
TAPE RECORDING & PLAYBACK
EN
TAPE RECORDING
&
PLAYBACK
CONTENTS
TAPE RECORDING ......................... 16 – 20
Basic Recording ..................................... 16
Journalistic Shooting ............................... 17
Self-Recording ...................................... 17
Operation Mode .................................... 17
Zooming ............................................ 18
Video Light ......................................... 19
Time Code ........................................... 20
TAPE PLAYBACK ........................... 21 – 24
Normal Playback ................................... 21
Still Playback ....................................... 21
Shuttle Search ...................................... 21
Frame-By-Frame Playback ........................ 21
Connections .................................. 22 – 23
Blank Search ........................................ 24
15
16
EN
TAPE RECORDING
Power lamp
Power Switch
Lock Button
Recording Start/Stop Button
Display
min
(Now calculating)
PUSH OPEN Button
90 min
(Blinking) (Blinking) (Blinking)
GHT
BR I
180°
90°
During
shooting
25
min
Tape remaining time indicator (Approximate)
89 min
1 min0 min
VIDEO/MEMORY Switch (GR-DVL767/DVL367/ DVL365 only)
3 min
2 min
MENU/BRIGHT Wheel
Basic Recording
NOTE:
You should already have performed the procedures listed below. If not, do so before continuing.
Power ( pg. 8)
Grip Adjustment (
Viewfinder Adjustment (
Load A Cassette (
Recording Mode Setting (
pg. 10)
pg. 10)
pg. 12)
pg. 13)
1 Remove the lens cap.
GR-DVL767/DVL367/DVL365 only: Press PUSH OPEN, open the LCD monitor and set the VIDEO/ MEMORY Switch to VIDEO”.
M
or
ANUAL
2 Set the Power Switch to “
while pressing down the Lock Button located on the switch. Shooting while using the LCD monitor: Make sure the LCD monitor is fully open. Tilt it upward/ downward for best viewability. Shooting while using the viewfinder: Close the LCD monitor.
The power lamp lights and the camcorder enters the Record-Standby mode. “PAUSE” is displayed.
AUTO
3 Press the Recording Start/Stop Button.
appears while recording is in progress.
T o Stop Recording . . .
.....press the Recording Start/Stop Button. The
camcorder re-enters the Record-Standby mode.
T o Adjust The Brightness Of The Display . . .
.....rotate the MENU/BRIGHT wheel until the bright
level indicator on the display moves and the appropriate brightness is reached.
NOTES:
If the Record-Standby mode continues for 5 minutes,
the camcorders power shuts off automatically. To turn the camcorder on again, set the Power Switch to OFF, then back to
The image will not appear simultaneously on the LCD
monitor and the viewfinder. It will appear in the viewfinder when the LCD monitor is in the lock position, and it will appear on the LCD monitor when fully extended.
When a blank portion is left between recorded scenes
on the tape, the time code is interrupted and errors may occur when editing the tape. To avoid this, refer to Recording from the middle of a tape (
To turn the tally lamp or beep sounds off,
48.
AUTO
or
M
ANUAL
”.
pg. 20).
pg. 46,
Tally lamp (lights while recording is in progress)
For other notes, pg. 67
M
ANUAL
Self­Recording
EN
17
JOURNALISTIC SHOOTING
In some situations, different shooting angles may provide more dramatic results. Hold the camcorder in the desired position and tilt the LCD monitor in the most convenient direction. It can rotate 270° (90° downward, 180° upward).
SELF-RECORDING
You can shoot yourself while viewing your own image in the LCD monitor. Open the LCD monitor and tilt it upward 180° so that it faces forward, then point the lens toward yourself and start recording.
To turn on the camcorder, set the Power Switch to any operation mode except “OFF”while pressing down the Lock Button located on the switch.
Power Switch
Power lamp
Lock Button
VIDEO/MEMORY Switch (GR-DVL767/DVL367/DVL365 only; open the LCD monitor to access this switch.)
When the Power Switch is set to When set to
(GR-DVL767/DVL367/DVL365 only)
1024
When the Power Switch is set to the VIDEO/MEMORY Switch is set to “MEMORY”, the currently selected image size appears. When set to VIDEO, there is no indication.
M
A
N
U
A
L
or PLAY, there is no indication.
AUTO
, “ ” appears.
AUTO
or
M
A
N
U
A
L
AUTO
OFF PLAY
M
A
N
U
A
L
and
Operation Mode
Choose the appropriate operation mode according to your preference using the Power Switch and VIDEO/ MEMORY Switch (GR-DVL767/DVL367/DVL365 only).
Power Switch Position
:
Allows you to set various recording functions using the Menus. If you want more creative capabilities than Full Auto recording, try this mode.
AUTO
(Full Auto):
Allows you to record using NO special effects or manual adjustments. Suitable for standard recording.
OFF:
Allows you to switch off the camcorder.
PLAY:
Allows you to play back a recording on the tape.
Allows you to transfer a still image recorded on the
tape to a computer (GR-DVL160 only).
Allows you to access data stored on the memory card or to transfer a still image stored on the memory card to a computer (GR-DVL767/DVL367/ DVL365 only).
VIDEO/MEMORY Switch Position
(GR-DVL767/DVL367/DVL365 only)
VIDEO:
Allows you to record on a tape or play back a tape.
If REC SELECT is set to DSC Menu Screen, still images are recorded on the memory card as well.
Zoom magnification over 10X is available
( pg. 18, 47).
MEMORY:
Allows you to record on a memory card or access data stored on a memory card.
/ in the
18
EN
TAPE RECORDING
(cont.)
Zoom in (T: Telephoto)
1x
WT
01x
Approximate zoom ratio
01x
WT
Zoom display
WT
Power Zoom Lever
02x
WT
Zoom out (W: Wide angle)
Digital zoom zone
10X (optical) zoom zone
04x
WT
FEATURE:
Zooming
PURPOSE:
To produce the zoom in/out effect, or an instanta­neous change in image magnification.
OPERATION:
Zoom In
Slide the Power Zoom Lever towards “T”.
Zoom Out
Slide the Power Zoom Lever towards “W”. The further you slide the Power Zoom Lever, the
quicker the zoom action.
NOTES:
Focusing may become unstable during Zooming. In
this case, set the zoom while in Record-Standby, lock the focus by using the manual focus
pg. 43), then zoom in or out in Record mode.
(
Zooming is possible to a maximum of 500X, or it
can be switched to 10X magnification using the optical zoom (
Zoom magnification of over 10X is done through
Digital image processing, and is therefore called Digital Zoom.
During Digital zoom, the quality of image may
suffer.
Digital zoom cannot be used when the VIDEO/
MEMORY Switch is set to MEMORY” (
Macro shooting (as close as approx. 5 cm to the
subject) is possible when the Power Zoom Lever is set all the way to “W”. Also see TELE MACRO in the Menu Screen on page 48.
pg. 47).
pg. 17).
EN
19
LIGHT OFF/AUTO/ON Switch (Open the LCD monitor to access this switch.)
DANGER
The video light can become extremely
hot. Do not touch it either while in operation or soon after turning it off, otherwise serious injury may result.
Do not place the camcorder into the carrying case
immediately after using the video light, since it remains extremely hot for some time.
When operating, keep a distance of about 30 cm
between the video light and people or objects.
Do not use near flammable or explosive materials.Do not place the camcorder in a cabinet or box while
the video light is in operation.
When using the video light, if you wish to install the
camcorder in a fixed position, attach it to a tripod, etc. Do not affix it directly to a surface such as a table top.
It is recommended that you consult your nearest JVC
dealer for replacing the video light.
FEATURE:
Video Light
PURPOSE:
To brighten the scene when natural lighting is too dim.
OPERATION:
Set LIGHT OFF/AUTO/ON as required: OFF : Turns off the light. AUTO: Automatically turns on the light when the
camcorder senses insufficient lighting on the subject.
ON : Always keeps the light on as long as the
camcorder is turned on.
The video light can only be used with the
camcorders power on.
It is recommended to set the white balance
( pg. 45) to when you use the video light.
When not using the video light, turn it off to save
battery power.
NOTES:
Even if the battery indicator ( ) does not blink
due to low battery charge, the camcorder may turn off automatically when you turn on the video light, or when you start recording with the video light turned on.
When LIGHT OFF/AUTO/ON is set to AUTO”:
Depending on the lighting conditions, the video
light may keep turning on and off. In this case, manually switch the light on or off using LIGHT OFF/AUTO/ON.
While the SHUTTER or SPORTS mode
pg. 39) is engaged, the light is likely to stay
( on.
While the TWILIGHT mode ( engaged, the light will not activate.
While the Night-Scope mode ( engaged, the light will not activate.
pg. 39) is
pg. 38) is
20
EN
TAPE RECORDING
(cont.)
Time Code
During recording, a time code is recorded on the tape. This code is to confirm the location of the recorded scene on the tape during playback. If recording starts from a blank portion, the time code begins counting from “00:00:00” (minute:second:frame). If recording starts from the end of a previously recorded scene, the time code continues from the last time code number.
To perform Random Assemble Editing ( pg. 58 – 62), time code is necessary. If during recording a blank portion is left partway through the tape, the time code is interrupted. When recording is resumed, the time code starts counting up again from “00:00:00”. This means the camcorder may record the same time codes as those existing in a previously recorded scene. To prevent this, perform “Recording From The Middle of A Tape” below in the following cases;
• When shooting again after playing back a recorded tape.
• When power shuts off during shooting.
• When a tape is removed and re-inserted during shooting.
• When shooting using a partially recorded tape.
• When shooting on a blank portion located partway through the tape.
• When shooting again after shooting a scene then opening/closing the cassette holder cover.
Recording From The Middle Of A Tape
1. Play back a tape or use Blank Search ( pg. 24) to find the spot at which you want to start recording,
then engage the Still Playback mode ( pg. 21).
M
” or “
ANUAL
” while pressing down the Lock Button located on the switch,
2. Set the Power Switch to “
AUTO
then start recording.
NOTES:
The time code cannot be reset.
During fast-forwarding and rewinding, the time code indication does not move smoothly.
The time code is displayed only when “TIME CODE” is set to “ON” ( pg. 49, 50).
12: 34 : 24
Display
Frames are not displayed during recording.
Minutes Seconds Frames
(25 frames = 1 second)
When a blank portion is recorded on a tape
Time code 00:00:00
Tape
Shooting start point
Time code 05:43:21
Time code 00:00:00
Shooting start pointShooting stop point
Proper recording
Time code 00:00:00
Tape
Shooting start point Shooting start point Shooting start point
Time code 05:43:21
Time code 05:44:00
Newly recorded sceneBlankAlready recorded scene
Latest sceneNew sceneAlready recorded scene
TAPE PLAYBACK
EN
21
Speaker
Stop Button (5) Rewind Button (2) Play/Pause Button ( Fast-Forward Button (
Power Zoom Lever (VOL.)
VIDEO/MEMORY Switch (GR-DVL767/DVL367/ DVL365 only; open the LCD monitor to access this switch.)
4
/6)
3
)
Normal Playback
1 Load a tape ( pg. 12). 2 Set the VIDEO/MEMORY Switch to VIDEO
(GR-DVL767/DVL367/DVL365 only), then set the Power Switch to PLA Y” while pressing down the Lock Button located on the switch. To start playback, press 4/6.
To stop playback, press 5.
Press 2 to rewind, or 3 to fast-forward the tape
during Stop mode.
To Control The Speaker Volume . . .
.....slide the Power Zoom Lever (VOL.) towards +
to turn up the volume, or towards “–” to turn down the volume.
NOTES:
If Stop mode continues for 5 minutes when power is supplied from a battery, the camcorder shuts off automatically. To turn on again, set the Power Switch to “OFF”, then to “PLAY”.
The playback picture can be viewed in the LCD monitor, viewfinder or on a connected TV ( pg. 22).
You can also view the playback picture on the LCD monitor with it flipped over and pushed against the camera body.
LCD monitor/viewfinder indications:
When power is supplied from a battery: the
When power is supplied from an AC outlet:
During Stop mode, none of the indications are displayed.
When a cable is connected to the AV connector, the sound is not heard from the speaker.
Still Playback:
1) Press 4/6 during playback.
2) To resume normal playback, press 4/6 again.
If still playback continues for more than about 3 minutes, the camcorder’s Stop mode is automatically engaged. After 5 minutes in the Stop mode, the camcorders power is automatically turned off.
When 4/6 is pressed, the image may not pause immediately while the camcorder stabiliseds the still image.
Shuttle Search:
1) Press 3 for forward or 2 for reverse search during playback.
2) To resume normal playback, press 4/6.
During playback, press and hold 2 or 3. The search continues as long as you hold the button. Once you release it, normal playback resumes.
A slight mosaic effect appears on screen during Shuttle Search. This is not a malfunction.
Pauses during playback.
Allows high-speed search in either direction.
battery pack remaining power indicator is displayed. does not appear.
Frame-By-Frame Playback: Allows frame-by-frame search.
1) Engage Still Playback.
2) Rotate the MENU/BRIGHT wheel towards + for forward Frame-By-Frame Playback, or towards “–” for reverse
Frame-By-Frame Playback during Still Playback.
To resume normal playback, press 4/6.
You can also use the provided remote control for Frame-By-Frame Playback ( pg. 56).
Slow-Motion Playback/Playback Special Effects and Playback Zoom
Available only with the remote control (provided) ( pg. 56, 57).
ATTENTION
During Shuttle Search, parts of the picture may not be clearly visible, particularly on the left side of the screen.
22
EN
TAPE PLAYBACK
Connections
Use the provided Audio/Video cable and optional S-Video cable.
To AV
When the S-Video cable is not used.
p
Audio/Video cable
To S-VIDEO
[mini-plug to RCA plug] (provided)
S-Video cable (optional)
Connector cover*
* When connecting the cables, open this cover. ** The Audio cable is not required for watching still images only.
Yellow to VIDEO IN
White to AUDIO L IN**
Red to AUDIO R IN**
To S-VIDEO IN
(cont.)
To TV or VCR
TV
VCR
If your TV/VCR has a 21-pin connector
Use the provided Cable Adapter.
Audio/Video cable [mini-plug to RCA plug] (provided)
White to
To AV
AUDIO L*
Camcorder
To S-VIDEO
*The Audio cable is not required for watching still images only.
S-Video cable (optional)
NOTE:
Set the video out select switch of the cable adapter as required: Y/C : When connecting to a TV or VCR which accepts Y/C signals and uses an S-Video cable. CVBS : When connecting to a TV or VCR which does not accept Y/C signals and uses an audio/video cable
When the S-Video cable is not used.
p
Yellow
Red to AUDIO R*
-IN
To
Cable Adapter
Y/C/CVBS Video Out Select Switch
TV or VCR
.
EN
23
1 Make sure all units are turned off. 2 Connect the camcorder to a TV or VCR as shown
in the illustration ( pg. 22).
If using a VCR . . . go to step 3. If not . . . go to step 4.
3 Connect the VCR output to the TV input, referring
to your VCRs instruction manual.
4 Turn on the camcorder, the VCR and the TV. 5 Set the VCR to its AUX input mode, and set the
TV to its VIDEO mode.
To choose whether or not the following displays appear on the connected TV . . .
Date/Time
.....set DATE/TIME to AUTO, ON or OFF in the
Menu Screen ( pg. 50). Or, press DISPLAY on the remote control (provided) to turn on/off the date indication.
Time Code
.....set TIME CODE to ON or OFF in the Menu
Screen ( pg. 50).
Playback Sound Mode, Tape Speed And Tape
Running Displays for tape playback
.....set ON SCREEN to LCD or LCD/TV in the
Menu Screen ( pg. 50).
NOTES:
It is recommended to use the AC Adapter as the power supply instead of the battery pack (
To monitor the picture and sound from the camcorder without inserting a tape or memory card*, set the camcorders Power Switch to then set your TV to the appropriate input mode.
* GR-DVL767/DVL367/DVL365 only
Make sure you adjust the TV sound volume to its minimum level to avoid a sudden burst of sound when the camcorder is turned on.
If you have a TV or speakers that are not specially shielded, do not place the speakers adjacent to the TV as interference will occur in the camcorder playback picture.
While the Audio/Video cable is connected to the AV connector, sound cannot be heard from the speaker.
AUTO
or
pg. 9).
M
AN
UAL
”,
24
EN
BLANK Button
Power Switch
Lock Button
Display
44
BLANK SEARCH
VIDEO/MEMORY Switch (GR-DVL767/ DVL367/DVL365 only; open the LCD monitor to access this switch.)
Stop Button (5)
TAPE PLAYBACK
(cont.)
Blank Search
Helps you find where you should start recording in the middle of a tape to avoid time code interruption ( pg. 20).
1 Load a tape ( pg. 12). 2 Set the VIDEO/MEMORY Switch to VIDEO
(GR-DVL767/DVL367/DVL365 only), then set the Power Switch to PLAY while pressing down the Lock Button located on the switch.
3 Press BLANK.
•“BLANK SEARCH appears blinking and the
camcorder automatically starts reverse or forward shuttle search, then stops at the spot which is about 3 seconds of tape before the beginning of the detected blank portion.
To cancel Blank Search midway . . .
..... press 5.
NOTES:
In step 3, if the current position is at a blank portion the camcorder searches in the reverse direction, and if the current position is at a recorded portion the camcorder searches in the forward direction.
Blank Search does not work if “HEAD CLEANING REQUIRED. USE CLEANING CASSETTE has appeared with the tape.
If the beginning or end of the tape is reached during Blank Search, the camcorder stops automatically.
A blank portion which is shorter than 5 seconds of tape may not be detected.
The detected blank portion may be located between recorded scenes. Before you start recording, make sure there is no recorded scene after the blank portion.
MEMORY CARD RECORDING & PLAYBACK
MEMORY CARD
Memory Card recording features are available on GR-DVL767, GR-DVL367 and GR-DVL365.
MEMORY CARD RECORDING ......... 26 – 27
Basic Shooting (Snapshot) ............... 26 – 27
MEMORY CARD PLAYBACK ........... 28 – 29
Normal Playback .................................. 28
Auto Playback ..................................... 28
Index Playback .................................... 29
RECORDING
&
PLAYBACK
CONTENTS
EN
25
Viewing File Information ......................... 29
Removing On-Screen Display .................... 29
ADVANCED FEATURES ....................30 – 36
Protecting Files .................................... 30
Deleting Files ...................................... 31
Dubbing Still Images Recorded On A Tape To A
Memory Card ....................................... 32
E-Mail Clip Recording ............................. 33
Setting Print Information
(DPOF Setting)............................. 34 – 35
Making A New Folder ............................ 36
Initialising A Memory Card ...................... 36
26
EN
Lock Button
SNAPSHOT Button
Power Switch
VIDEO/MEMORY Switch (Open the LCD monitor to access this switch.)
MEMORY CARD RECORDING
Basic Shooting (Snapshot)
You can use your camcorder as a digital still camera for taking snapshots.
NOTE:
You should already have performed the procedures listed below. If not, do so before continuing.
pg. 8)
Power (
Grip Adjustment (
Viewfinder Adjustment (
Loading A Memory Card (
Picture Quality/Image Size Setting (
1 Set the VIDEO/MEMORY Switch to “MEMORY,
then set the Power Switch to while pressing down the Lock Button located on the switch.
pg. 10)
pg. 10)
pg. 14)
AUTO
pg. 14)
M
or
ANUAL
2 Press SNAPSHOT. “PHOTO appears while the
snapshot is being taken. The image is recorded on the memory card.
Still images are recorded in the snapshot mode with
no frame.
1024
Display
Image Size
Displays the image file size: 1280 (1280 x 960)*, 1024 (1024 x 768) or 640 (640 x 480)
pg. 14).
(
GR-DVL767 only.
*
Shooting icon
Appears and blinks during shooting.
Card icon
Appears during shooting and blinks when a memory card is not loaded:
51
(SD Memory Card) or (MultiMediaCard).
Remaining number of shots
Displays the remaining number of shots that can be stored. The number increases or decreases depending on the Picture Quality/Image Size, etc.
Picture Quality
Displays the quality of image: F (Fine) or S (Standard) (in order of quality) (
pg. 14).
EN
27
FULL Snapshot mode with no frame
To Delete Unwanted Still Images . . .
.....when unwanted still images are stored in the
memory card or its memory is full, refer to Deleting Files ( pg. 31) and delete unwanted still images.
To Remove The Shutter Sound . . .
.....when you do not want to hear the shutter sound,
set BEEP to OFF in the Menu Screen ( pg. 46, 48). The sound is no longer heard
There is the sound of a shutter closing.
To Protect Valuable Files (available only for SD Memory Card) . . .
Write/erase protection tab
. . . slide the write/erase protection tab on the side
of the memory card in the direction of LOCK. This prevents the memory card from being recorded over. To record on this memory card, slide the tab back to the position opposite to “LOCK” before loading it.
Approximate Number of Storable Images <GR-DVL367/DVL365
Image Size/Picture Quality
1024 x 768/FINE 20 45 95 190 24 48 100 1024 x 768/
STANDARD 640 x 480/FINE 45 95 205 405 55 105 215 640 x 480/
STANDARD
8MB 16MB 32MB 64MB 8MB 16MB 32MB
65 145 310 605 75 160
160 295 625 1215 190 320 645
SD Memory Card MultiMediaCard
from the speaker.
NOTES:
Even if “DIS is set to ON ( pg. 47), the Stabilisedr will be disabled.
If Snapshot recording is not possible, “PHOTO blinks when SNAPSHOT is pressed.
If Programme AE with special effects ( engaged, certain modes of Programme AE with special effects are disabled during Snapshot recording. In such a case, the icon blinks.
If shooting is not performed for approx. 5 minutes when the Power Switch is set to power is supplied from the battery pack, the camcorder shuts off automatically to save power. To perform shooting again, set the Power Switch to “OFF”, then to
AUTO
The Motor Drive mode (
VIDEO/MEMORY Switch is set to MEMORY”.
Still images taken are compliant to DCF (Design rule for Camera File system). They do not have any compatibility with devices which are not compliant to DCF.
or
MANUAL
AUTO
”.
pg. 42) is disabled when the
pg. 38) is
M
or
ANUAL
>
and
320
Approximate Number of Storable Images <GR-DVL767
Image Size/Picture Quality
1280 x 960/FINE 12 28 62 120 16 32 64 1280 x 960/
STANDARD 1024 x 768/FINE 20 46 98 190 25 50 100 1024 x 768/
STANDARD 640 x 480/FINE 46 98 205 405 50 105 210 640 x 480/
STANDARD
8MB 16MB 32MB 64MB 8MB 16MB 32MB
44 98 205 405 50 100 200
66 145 310 605 80 160
150 295 625 1215 160 320 640
SD Memory Card MultiMediaCard
>
320
NOTE:
The number of storable images depends on the selected picture quality as well as the composition of the subjects in the images and the type of memory card being used.
Loading...
+ 61 hidden pages