JVC GM-X50C/PLASMA, GM-X50E, GM-X50S, GM-X50U, GM-X50U/PLASMA Service manual & schematics

Page 1
Preliminary
SERVICE MANUAL
PLASMA DISPLAY MONITOR
YA06720044
GM-X50U, GM-X50E, GM-X50S
BASIC CHASSIS
U1
RM-C579 REMOTE CONTROL UNIT
ON
POWER
OFF
ASPECT
DISPLAY
INPUT SELECT
COMPO.
A
/(RGB B)
VIDEO
RGB AB
MUTING
VOLUME
MENU/EXIT
MENU INPUT POWER
TABLE OF CONTENTS
1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24
5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-91
COPYRIGHT © 2004 VICTOR COMPANY OF JAPAN, LIMITED
No.YA067
2004/4
Page 2
SPECIFICATION
Contents
Items
Type Plasma display Dimension (W × H × D) 123.2cm × 74.3cm × 10.2cm (48-5/8" × 29-3/8" × 4-1/8") Mass 50kg (110 lbs) Video System VIDEO A/B NTSC3.58 NTSC3.58, NTSC4.43, PAL, PAL60, SECAM
COMPONENT 480i, 576i, 480p, 576p, 720/60p, 720/50p, 1080/50i, 1080/60i (1035/60i) Power Requirements AC120V, 60Hz AC220V ~ AC240V, 50Hz / 60Hz Rated Input Current 2.4A 2.2A Operation Environment Temperature : 0°C ~ 40°C
Storage Environment Temperature : -20°C ~ +60°C
Plasma Display Panel
Effective Screen Dimensions
Speaker 4cm × 7cm oval type, Impeadance 8 Audio power output Speaker output : 2W+2W (TYP at impedance 6Ω) Input / Output
Terminals
Accessories Remote control unit (RM-C579) × 1, AA/R6-size dry cell battery × 2(for operation check)
Design and specifications are subject to change without notice.
Pixel Number
Pixel Pitch
Cell Pitch
Display Colours
Aspect Ratio
VIDEO A
(IN / OUT)
VIDEO B
(INPUT)
RGB A (INPUT)
COMPONENT/
RGB B (INPUT)
AUDIO OUT Output impedance 600, RCA pin jack × 2
SPEAKER OUT Impedance 6 ~ 8 (L/R)
REMOTE RS-232C D-sub 9-pin connector × 1
OPTION DC Power supply for cooling fan (DC15V), DC jack × 1
Relative humidity : 10% ~ 90% (non-condensing) Pressure : 800hPa ~ 1100hPa
Relative humidity : 10% ~ 90%(non-condensing) Pressure : 700hPa ~ 1100hPa
Diagonal : 127.0cm, (W) 110.7cm × (H) 62.2cm [Diagonal : 50", (W) 43-9/16" × (H) 24-7/16"] Horizontal 1366 × Vertical 768 (W-XGA) Horizontal 0.810mm × Vertical 0.810mm Horizontal 0.280mm × Vertical 0.810mm 16,777,216 colours (256 colours for each of RGB) 16:9 (Wide format)
Video input 1V(p-p) / 75, BNC connector × 1 Video output 1V(p-p) / 75, BNC connector × 1 Audio input 500mV(rms) / high impedance, RCA pin jack connector × 2(L/R) Y/C Mini-DIN 4pin connector × 1
Video 1V(p-p) / 75, RCA pin jack × 1 Audio 500mV(rms) / high impedance, RCA pin jack × 2
[ Horizontal sync (HD) ] [ Composite sync (Cs) ]
[ Vertical sync (VD) ]
Audio 500mV(rms) / high impedance, 3.5mm stereo mini jack × 1 COMPONENT BNC connector × 3
RGB
HD [ Horizontal sync ] Cs [ Composite sync ]
VD [ Vertical sync ]
Audio 500mV(rms) / high impedance, RCA pin jack × 2
MAKE Mini-DIN 4pin connector × 1 WIRED 3.5mm stereo mini jack connector × 1
Ferrite core × 2, Power cord (approx 2.5m) × 1
GM-X50U
RGB
[Analog RGB]
Y : 1V(p-p) / 75 C : 0.286V(p-p) / 75Ω [NTSC]
0.3V(p-p) 75 [PAL/SECAM]
D-sub 3-row 15-pin connector × 1 R / G / B : 0.7V(p-p) / 75 G on sync : 1V(p-p) / 75 (negative syncy) HD : 0.3V(p-p) ~ 5V(p-p) / 470 (positive / negative polarity) Cs : 0.3V(p-p) ~ 5V(p-p) / 470 (positive / negative polarity) VD : 1V(p-p) ~ 5V(p-p) / 470 (positive / negative polarity)
Y : 1V(p-p) / 75 Pb/B-Y : 0.7V(p-p) / 75 Pr/R-Y : 0.7V(p-p) / 75
BNC connector × 5 R : 0.7V(p-p) / 75 G : 0.7V (p-p) / 75 G on sync : 1V(p-p) / 75 (negative sync) B : 0.7V (p-p) / 75
0.3V(p-p) ~ 5V(p-p) / 1k (positive / negative polarity) / 75
0.3V(p-p) ~ 5V(p-p) / 1k (positive / negative polarity) / 75 1 V(p-p) ~ 5V(p-p) / 1k (positive / negative polarity) / 75
GM-X50E GM-X50S
1-2 (No.YA067)
Page 3
SECTION 1
PRECAUTION
1.1 SAFETY PRECAUTIONS
(1) The design of this product contains special hardware,
many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Service should be performed by qualified personnel only.
(2) Alterations of the design or circuitry of the products should
not be made. Any design alterations or additions will void the manufacturer's warranty and will further relieve the manufacturer of responsibility for personal injury or property damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the parts list of Service manual. Electrical components
having such features are identified by shading on the schematics and by ( ) on the parts list in Service manual. The use of a substitute replacement which does
not have the same safety characteristics as the recommended replacement part shown in the parts list of Service manual may cause shock, fire, or other hazards.
(4) Don't short between the LIVE side ground and
ISOLATED (NEUTRAL) side ground or EARTH side ground when repairing.
Some model's power circuit is partly different in the GND. The difference of the GND is shown by the LIVE : ( ) side GND, the ISOLATED (NEUTRAL) : ( ) side GND and EARTH : ( ) side GND. Don't short between the LIVE side GND and ISOLATED (NEUTRAL) side GND or EARTH side GND and never measure the LIVE side GND and ISOLATED (NEUTRAL) side GND or EARTH side GND at the same time with a measuring apparatus (oscilloscope etc.). If above note will not be kept, a fuse or any parts will be broken.
(5) If any repair has been made to the chassis, it is
recommended that the PDP voltage setting should be checked or adjusted.
(6) When service is required, observe the original lead dress.
Extra precaution should be given to assure correct lead dress in the high voltage circuit area. Where a short circuit has occurred, those components that indicate evidence of overheating should be replaced. Always use the manufacturer's replacement components.
(7) Isolation Check (Safety for Electrical Shock Hazard)
After re-assembling the product, always perform an isolation check on the exposed metal parts of the cabinet (antenna terminals, video/audio input and output terminals, Control knobs, metal cabinet, screw heads, earphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.
a) Dielectric Strength Test
The isolation between the AC primary circuit and all metal parts exposed to the user, particularly any exposed metal part having a return path to the chassis should withstand a voltage of 3000V AC (r.m.s.) for a period of one second. (. . . . Withstand a voltage of 1100V AC (r.m.s.) to an appliance rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated 200V or more, for a period of one second.) This method of test requires a test equipment not generally found in the service trade.
b) Leakage Current Check
Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Using a "Leakage Current Tester", measure the leakage current from each exposed metal part of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground (water pipe, etc.). Any leakage current must not exceed 0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.2mA AC (r.m.s.).
Alternate Check Method
Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Use an AC voltmeter having 1000 per volt or more sensitivity in the following manner. Connect a 1500 10W resistor paralleled by a 0.15µF AC-type capacitor between an exposed metal part and a known good earth ground (water pipe, etc.). Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Any voltage measured must not exceed 0.75V AC (r.m.s.). This corresponds to
0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.3V AC (r.m.s.). This corresponds to 0.2mA AC (r.m.s.).
AC VOLTMETER (HAVING 1000 /V, OR MORE SENSITIVITY)
0.15 F AC-TYPE
GOOD EARTH GROUND
1500 10W
PLACE THIS PROBE ON EACH EXPOSED ME TAL PAR T
(No.YA067)1-3
Page 4
1.2 INSTALLATION
1.2.1 REQUIREMENTS FOR SETTING
The following minimum space must be kept when a PDP is installed. (The recommended distance should be from the most projected portion when a PDP is inclined.) An insufficient space reduces cooling efficiency and raises the internal temperature. If the internal temperature rises over the reference value, the temperature sensor works to turn the power off for protecting the main body. Therefore, vents on the backside of the main body such as heat dissipation vents must not be blocked, and sufficient spaces for heat dissipation must be kept around the main body.
Methods of Installation
1
Hanging from a wall [Horizontal]
2
Hanging from a wall [Vertical]
10cm
10cm
10cm
Front
Wall
Wall
20cm
15cm
10cm10cm
10cm
Flank Remarks
Front Wall
5cm
Wall
5cm
It is necessary to set the cooling fan where install each side causes high temperature within a PDP and may damage the inner circuit.
Do not prevent the radiation of heat from back, top and flank sides of a PDP. Preventing the radiation of heat from each side causes high temperature within a PDP and may damage the inner circuit.
Install a PDP in a place where is well ventilated. Ambient temperature should be within a range of 0 ~40 .
Exclusive fixtures (option) should be used.
3
Suspension from a ceiling
4
Desktop
10cm
15cm
5cm
10cm
Wall
Wall
20cm
20cm
10cm
15cm
Front
Front
5cm
5cm
Wall
Wall
The structure and strength of the wall where a PDP is installed should be checked beforehand so as to install the PDP safety without any accident.
In the case of vertical setting, 2 exclusive cooling fans(option) should be attached. Additionally, the rotation of internal cooling fans should be "high "(see also the instruction manual).
A PDP should be installed on a rigid floor or stand.
In order to prevent a PDP from turning over by an accident or earthquake, safety measures should be considered.
1-4 (No.YA067)
Page 5
1.2.2 PRECAUTION DURING NOTES FOR TRANSPORTATION
When transporting the display unit, pressure exerted on the internal PDP (Plasma Display Panel) due to improper handing (such as tossing and dropping) may cause damages even when the unit is carefully packed. To prevent accidents from occurring during transportation, pay careful attention prior to delivery such as through exchanging the handing instructions to transporters. Ensure that the following requirements are met during transportation, as the PDP of this unit is made of glass and therefore fragile.
(1) Avoid vibrations and impacts
The unit may be broken if it is toppled sideways even when properly packed. Ensure that the unit is carried by at least 2 persons and pay careful attention not to exert any vibration or impact on it.
(2) Do not place equipment lay a PDP on its side.
A PDP should always be placed upright during both transportation and safekeeping. Don't lay it on its side. The panel of a PDP is very fragile to the impact in the horizontal direction. When a car carries a PDP, load it on board the car in parallel with the moving direction of the car. Don't lay several PDPs one on top another. During safekeeping, don't lay more than two PDPs one on top another even if they are kept upright.
1.2.4 RETAINED-IMAGE / BURN-IN ON SCREEN
Like CRTs, "burn-ins" may occur when a same image is continuously displayed over an extended period of time. As this may also shorten the life span of the PDP. Therefore, turn off the display when not in use, scroll the screen, make use of screen-savers, or allow even distribution on the display by inverting the brightness, switching to complementary colors or inverting animated images at periodic intervals. As burn-in is more likely to occur with high brightness and contrast settings, try to use neutral gradations or medium tone colors. Burn-in dose not occur in the case of animated images. When switching to another image after continuous display of the previous image, residual images may become prominent, as luminance in a part of the display is higher then the other parts. This is not a defect but is because due to the discharge surface of the lighted portion has become being relatively activated and its luminance higher than the unlighted parts.
1.2.5 BRIGHTNESS CHANGE IN THE SCREEN
In order to save the power consumption, the power is controlled (with APS function) depending on the brightness of the screen. For this, the brightness may change after a short time when the picture of the screen is changed. However, this phenomenon is not a trouble.
1.2.3 HEAT DISSIPATION IN THE CASE OF VERTICAL SETTING
In the case of vertical installation, it is required to attach 2 exclusive cooling fans(option) in order to help dissipate the heat within the PDP unit. Connect the DC power code of exclusive cooling fans to the exclusive optional terminal. If you install the PDP in other ways such as on the angle, not only cooling fans but additional methods are required to cool down the PDP depending on the thermal environment.
An option terminal is exclusively for a cooling fan. Please do not use it for connection with other apparatus
Cooling Fan Unit (Option)
AC INAUDIO
L
R
OUT
MAKE
WIRED
RS-232C
REMOTE
OPTION
RGB A
AUDIO
IN
1.2.6 INFRARED RAYS
Because the near infrared rays (800nm~1000nm) radiate from the panel face, the neighboring infrared ray remote controllers, infrared communication systems, etc. may malfunction. In these cases, take a measure to prevent the trouble to be caused by direct rays (or reflected rays) from the screen by changing the direction of the screen face or keeping a safe distance between a PDP and other devices.
1.2.7 OPTICAL FILTER (FRONT FILTER)
Avoid placing the unit under direct sunlight over a prolonged period of time. This may cause the optical filter to deteriorate in quality and color. Clean the filter surface by wiping it softly lightly with outing flannels a soft and lightly fuzz cloth (such a flannel). Do not use solvents such as benzene or thinner to wipe the filter surface. This may cause the filter to deteriorate in quality or the coating on the surface to come off. As the filter surface is fragile. Do not scratch or hit it with hard materials.
1.2.8 NOTES PRECAUTIONS FOR REPLACEMENT OF EXTERIOR PARTS
Take note of the following when replacing exterior parts (back REAR COVER, FRONT PANEL, OPTICAL FILTER): Do not exert pressure on the front of the PDP(glass surface). Pay careful attention not to scratch or stain the front of the PDP (surface) with hands. When replacing exterior parts, the front of the PDP should be placed facing downward. Place a met, etc. underneath to avoid causing scratched to the front surface. However, never use materials that are too soft (such as blanket cloth). If replacement is made with the PDP surface facing downward and in contact with the blanket, pressure may be exerted on the PDP, thus causing damages to it.
(No.YA067)1-5
Page 6
SPECIFIC SERVICE INSTRUCTIONS
2.1 TIMING SPECIFICATION & SCAN SIZE
Divide Item
NTSC4.43,PAL M
COMPOSITE
Y / C
COMPONENT
PC / RGB 15k
PC / VGA 400
NTSC, PAL60,
(B/W-60Hz)
PAL, SECAM
PAL N
(B/W-50Hz)
480i 59.94 15.734 525 485
576i 50.00 15.625 625 575
480p
576p
720/50p SMPTE 296M 50.00 37.500 74.25 1980 750 1280 720 FULL 95.00 95.00
720/60p SMPTE 296M 60.00 45.000 74.25 1650 750 1280 720 FULL 95.00 95.00
1080/50i SMPTE 274M 50.00 28.125 74.25 2640 562.5 1920 1080 FULL 95.00 95.00
1080/60i SMPTE 274M 60.00 33.750 74.25 2200 562.5 1920 1080 FULL 95.00 95.00
1035i BTA S-001A 60.00 33.750 74.25 2200 562.5 1920 1035 FULL 92.75 92.75
RGB 15k / 60Hz 59.94 15.734 525 485
RGB 15k / 50Hz 50.00 15.625 625 575
PC98 (NEC) 56.42 24.82 21.05 848 440 640 400
VGA400-70 (IBM) 70.09 31.47 25.18 800 449 640 400
Standard
ITU-R
BT.1358
ITU-R
BT.1358
SECTION 2
Input picture format ЙXЙLЙЙЙму¶
Frequency Total pixel Visible area pixel
Vert. Hor. Dot Vert. Vert. Vert. Vert.
fVi fHi fci Hi Vi Hai Vai Kh Kv
Hz kHz MHz pixel/line line/frame pixel/line line/frame % %
59.94 15.734 525 485
50.00 15.625 625 575
59.94 31.468 27.00 858 525 720 483
50.00 31.250 27.00 864 625 720 576
Display
mode
REGULAR 95.00 95.00
FULL 95.00 95.00
PANORAMIC
ZOOM 95.00 71.25
REGULAR 95.00 95.00
FULL 95.00 95.00
PANORAMIC
ZOOM 95.00 71.25
REGULAR 95.00 95.00
FULL 95.00 95.00
PANORAMIC
ZOOM 95.00 71.25
REGULAR 95.00 95.00
FULL 95.00 95.00
PANORAMIC
ZOOM 95.00 71.25
REGULAR 95.00 95.00
FULL 95.00 95.00
PANORAMIC
ZOOM 95.00 71.25
REGULAR 95.00 95.00
FULL 95.00 95.00
PANORAMIC
ZOOM 95.00 71.25
REGULAR 95.00 95.00
FULL 95.00 95.00
PANORAMIC
ZOOM 95.00 71.25
REGULAR 95.00 95.00
FULL 95.00 95.00
PANORAMIC
ZOOM 95.00 71.25
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
Hor. Vert.
95.00 90.00
95.00 90.00
95.00 90.00
95.00 90.00
95.00 90.00
95.00 90.00
95.00 90.00
95.00 90.00
1-6 (No.YA067)
Page 7
Divide Item
PC / VGA 480
PC / SVGA
PC / XGA
PC/SXGA
PC/UXGA
Input picture format ЙXЙLЙЙЙму¶
Frequency Total pixel Visible area pixel
Standard
VGA-60 (Industry std.) 59.94 31.47 25.17 800 525 640 480
VGA-72 VESA std. 72.81 37.86 31.50 832 520 640 480
VGA-75 VESA std. 75.00 37.50 31.50 840 500 640 480
MAC 13Åh (Apple) 66.67 35.00 30.24 864 525 640 480
SVGA-56
SVGA-60
SVGA-72
SVGA-75
MAC 16Åh (Apple) 74.55 49.73 57.28 1152 667 832 624
XGA-60
XGA-70 VESA STD. 70.07 56.48 75.00 1328 806 1024 768
XGA-75 VESA STD.
XGA-85 VESA STD.
MAC 19Åh (Apple) 74.93 60.24 80.00 1328 804 1024 768
XGA+-75 VESA STD. 75.00 67.50 108.0 1600 900 1152 864
MAC 21Åh (Apple) 75.06 68.68 100.00 1456 915 1152 870
UXGA-60 VESA std. 60.02 63.98 108.00 1688 1066 1280 1024
SXGA-75 VESA std. 75.03 79.98 135.00 1688 1066 1280 1024
SXGA-60 VESA std. 60.00 75.00 162.00 2160 1250 1600 1200
UXGA-65 VESA std. 65.00 81.25 175.50 2160 1250 1600 1200
UXGA-70 VESA std. 70.00 87.50 189.00 2160 1250 1600 1200
VESA
GUIDELINES
VESA
GUIDELINES
VESA
GUIDELINES
VESA
GUIDELINES
VESA
GUIDELINES
Vert. Hor. Dot Vert. Vert. Vert. Vert.
fVi fHi fci Hi Vi Hai Vai Kh Kv
Hz kHz MHz pixel/line line/frame pixel/line line/frame % %
56.25 35.16 36.00 1024 625 800 600
60.32 37.88 40.00 1056 628 800 600
72.19 48.08 50.00 1040 666 800 600
75.00 46.88 49.5 1056 625 800 600
60.00 48.36 65.00 1344 806 1024 768
75.03 60.02 78.75 1312 800 1024 768
85.00 68.68 94.50 1376 808 1024 768
Display
mode
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
REGULAR 100.00 100.00
FULL 100.00 100.00
Hor. Vert.
(No.YA067)1-7
Page 8
2.2 MAIN DIFFERENCE LIST
Item GM-X50U GM-X50S GM-X50E
Power requirements AC120V 50Hz/60Hz AC220-240V 50Hz/60Hz Rated input current 4.0A 2.2A
2.3 TECHNICAL INFORMATION
2.3.1 PDP (PLASMA DISPLAY PANEL) DESCRIPTION
2.3.1.1 CAUTION
Although a PDP is made with highly advanced precision, this does not necessarily mean all of the cells operate correctly. The PDP inevitably includes cell that do not light or light constantly. If the specifications (PDP performance) are unclear at the time of shipment, an adequate description cannot be conveyed to the customer. In event of inquiries from customers regarding PDP performance, check the following specifications in order to offer a suitable reply.
2.3.1.2 CELL ARRANGEMENT
The PDP is constructed of front and rear glass substrates provided with respective discharge electrodes. Between these, neon for discharging and xenon for generating ultraviolet rays are enclosed. One picture element (pixel) is composed of Red, Green and Blue (RGB) cells. The cell pitch is 0.280mm horizontal (0.810mm per pixel) by 0.810mm vertical. As shown in Fig. 1, the cells are arranged for each R / G / B colour. A pixel consists of each cell of R/G/B/ colour. The size of a cell is
0.280mm horizontally and 0.810mm vertically.
Direction
Vertical(V)
1st pixel
2nd pixel
767th pixel
768th pixel
Horizontal(H)
line
line
line
line
1st pixel
array
B G R B G R
BG
G RBG R
B
GRBGR
B
H 0.810mm
Pitch of pixel
2nd pixel
array
RBG R
Fig.1 PIXEL (CELL) ARRANGEMENT
One pixel
(1dot)
B cell G cell R cell
1365th pixel
array
B GRBG R
BGRBGR
G RBG R
B
GRBGR
B
1366th pixel
array
H 0.280mm Pitch of cell
V 0.810mm Pitch of pixel (Pitch of cell)
1-8 (No.YA067)
Page 9
2.3.1.3 PIXEL FAULT
There are four pixel faults - bright fault , dark fault, flicker fault and uncontrollable fault - that are respectively defined as follows.
(1) BRIGHT FAULT
In this pixel fault, a cell that should not light originally is lighting on and off. For checking this pixel fault, input ALL BLACK SCREEN and find out the cell that is lighting on and off.
(2) DARK FAULT
In this pixel fault, a cell that should light originally is not lighting or lighting with the brightness twice as brighter as originally lighting. For checking this pixel fault, input 100% of each R/G/B colour and find out the cell that is not lighting.
(3) FLICKER FAULT
In this pixel fault, a cell that should light originally or not light originally is flashing on and off. For checking this pixel fault, input ALL BLACK SCREEN signal or 100% of each RGB colour and find out the cell that is flashing on and off.
(4) UNCONTROLLABLE FAULT
In this pixel fault, a cell is out of control due to an unstable condition. For checking this pixel fault, input 100% of each R/G/B colour and find out the cell that is lighting on and off.
2.3.1.4 PIXEL FAULT SPECIFICATION
Fault Screen display Criteria for number of faulted cell
BRIGHT FAULT All black screen A zone: 0
B zone: 0
DARK FAULT FLICKER FAULT
Red level 100% on entire screen A zone: 4 or less than 4 in each colour
Green level 100% on entire screen
B zone: 11 or less than 11 in each colour
Blue level 100% on entire screen
UNCONTROLLABLE FAULT
Red level 100% on entire screen A zone: 2 or less than 2 in each colour
Green level 100% on entire screen
B zone: 3 or less than 3 in each colour
Blue level 100% on entire screen
(1) OBJECT RANGE
A-zone : Center portion (area enclosed by 1/4 vertically from the top and bottom and 1/4 horizontally from the right and left sides.) B-zone : Other area
1/4H 1/4H
B zone
1/4V
1/4V
A zone
1/4V1/4V
(2) JUDGEMENT STANARD
Regardless of A and B zones, the following cases are considered as defects.
• When there are two or more dark faults or flicker faults in two contiguous cells.
• When there is one or more dark fault or flicker fault in three contiguous cells.
(No.YA067)1-9
Page 10
2.3.2 REMOTE THROUGH FUNCTION
The REMOTE THROUGH function is a function that is capable of controlling such equipment as a karaoke system connected to the REMOTE THROUGH terminal by receiving the IR (infrared ray) signal at the sensor of the remote controller unit of this model.
2.3.2.1 REMOTE THROUGH OUTPUT TERMINAL
The REMOTE THROUGH terminal and MAKE (mini DIN 4 pin) terminal at the back of the main body share the same terminal. Therefore, it is necessary to change the setup at the SERVICE MODE when the REMOTE THROUGH function is used. For the pin layout at the terminal, the 4 pin will become an output terminal and the 1-3 pins will be GNDs.
REMOTE THROUGH OUTPUT TERMINAL
2
65
34
Pin No.
1
2
3
1
4
5
6
Signal name
GND
GND
GND
OUTPUT
GND
DETECT SW
2.3.2.2 HOW TO CHANGE THE SETUP OF THE FUNCTION
(1) Enter the SERVICE MODE. (2) Select the < CPU BLOCK > with the [/] key. (3) Press the [] key of the remote control unit to display the < CPU BLOCK >. (4) Select the "CE: SYSTEM CONSTANT" with the [/] key. (5) Press the [] key of the remote control unit to display the setup screen for the "SYSTEM CONSTANT". (6) Display the "CE 05" with the [/] key. (7) Change the setup value to 001 from 000 with the [/] key. (8) Press the MENU key of the remote control unit to exit from the SERVICE MODE. (9) After turning the power off (or at the stand-by mode), turn the power on again.
(10) Then the REMOTE THROUGH function is available.
Note :
When an equipment is connected to the MAKE terminal, it is not able to operate any functions by the remote control unit. Therefore, before connection, it is necessary to enter the SERVICE MODE and change the setup of the function.
VCO ADJUST WHITE BALANCE BLOCK CPU BLOCK SIZE/POSITION BLOCK H POSITION BLOCK PANEL BLOCK SIGNAL BLOCK DEVICE INITIAL VALUE
ENTER: SELECT: EXIT:
SERVICE MODE
[1/2]
MENU
< CPU BLOCK >
CA:PANORAMA DATA CB:SIGNAL RANGE CC:SIZE/POSI. RANGE CD:FRQENCY DATA CE:SYSTEM CONSTANT CF:TEMP. SENSOR DATAs CG:APS CONTROL DATA CH:TEST MODE
ENTER: SELECT: EXIT:
<CPU BLOCK> screen
DIAGNOSIS BLOCK UPDATE CPU PROGRAM HOUR METER BLOCK ENHANCER BLOCK
ENTER: SELECT: EXIT:
MENU
[2/2]
MENU
C(E05)
SYSTEM CONSTANT screen
000 001
1-10 (No.YA067)
Page 11
2.3.3 HOUR METER FUNCTION
This model is equipped with an "HOUR METER" function that displays elapsed time on operating time of the set. Elapsed time can be checked at the "HOUR METER BLOCK" in the SERVICE MODE. Also you can reset elapsed time to zero if needed. Elapsed time count 1 hour. MAX elapsed time is 65535 hour.
HOW TO RESET ELAPSED TIME
(1) Enter the SERVICE MODE (Fig.1). (2) Press [/] key, and select "HOUR METER BLOCK" of
SERVICE MODE 2 page (Fig.2).
(3) Press [] key, and display "HOUR METER BLOCK"
screen (Fig.3).
(4) While the "HOUR METER BLOCK" display press []
key and it will display "RESET HOUR METER" (Fig.4).
(5) Press [] key and reset the HOUR METER (Fig.5).
SERVICE MODE
VCO ADJUST WHITE BALANCE BLOCK CPU BLOCK SIZE/POSITION BLOCK H POSITION BLOCK PANEL BLOCK SIGNAL BLOCK DEVICE INITIAL VALUE
ENTER: SELECT: EXIT:
[1/2]
MENU
Fig.1
2.3.4 REMINDER TO CHANGE A BATTERY
This model with a timer function, is equipped with a battery for the timer. When the battery is running low, a message of "BATTERY LOW" is displayed on the [TIMER], [COLOR-REVERSE] and [REFRESH] setting screen of the < SET-UP MENU >. At the end of the battery-life, a message of "BATTERY EMPTY" is displayed same screen. Both cases, you should make a battery change. Battery is fixed on the battery board. Please exchange the whole substrate.
BATTERY CHANGE PROCEDURE
(1) Remove the AV terminal board on the back of the main
body.
(Refer to disassembly procedure) (2) Remove the connector D on the battery board. (3) Remove the screw L attaching the battery board. (4) Change the battery board to new one.
Note :
After changing the battery board, the same message before a battery change will be displayed when the power is turned on for the first time. Therefore, turn off the power once, then turn on the power again. The message will be disappeared and you can use the model with normal functions.
DIAGNOSIS BLOCK UPDATE CPU PROGRAM HOUR METER BLOCK ENHANCER BLOCK
ENTER: SELECT: EXIT:
HOUR METER BLOCK
< HOUR METER BLOCK >
RESET HOUR METER (X1h) : 12345
ENTER: EXIT:
< RESET HOUR METER >
!
Are you sure ?
"YES" then Key
"NO" then Key
ENTER: SELECT: EXIT:
MENU
[2/2]
MENU
MENU
MENU
Fig.2
Fig.3
Fig.4
AV TERMINAL
BATTERY PWB
CND connector
L
THE CAUTIONS ON BATTERY EXCHANGE
Risk of explosion if battery is replaced by incorrect type. Dispose of used batteries according to the instructions.
< HOUR METER BLOCK >
RESET HOUR METER (X1h) : 00000
ENTER: EXIT:
MENU
Fig.5
(No.YA067)1-11
Page 12
SECTION 3
DISASSEMBLY
3.1 DISASSEMBLY PROCEDURE
• Prior to assembly/disassembly procedure of the set, be sure to disconnect the power cord from the wall outlet.
• Perform the following procedures on a flat and strong place.
3.1.1 REMOVING THE HANDLE (Fig.1)
(1) Remove the 2 screws [A]. (2) Remove the handle.
3.1.2 REMOVING THE REAR COVER (Fig.1)
• Remove the HANDLE. (1) Remove the 8 screws [B], 14 screws [C], 1 screw [D]. (2) Pull up the rear cover, and remove the rear cover.
3.1.3 REMOVING THE AV TERMINAL (Fig.2)
[Only GM-X50U, GM-X50S]
(1) Remove the 4 screws [E]. (2) Lift the both ends of the AV TERMINAL slowly, and remove
the CN5001 PWB. Then, remove the AV TERMINAL.
/CN5002 connectors connected to the MAIN
A
C
B
Fig.1
B
HANDLE
D
REAR COVER
G
A
HANDLE
B
C
C
AV TERMINAL
E
3.1.4 REMOVING THE PC TERMINAL (Fig.2)
• Remove the AV TERMINAL. (1) Remove the 6 screws [G] (2) Lift the both ends of the PC TERMINAL slowly, and remove
the CN5003 the MAIN PWB. Then, remove the PC TERMINAL.
/CN5004/CN5005 connectors connected to
PC TERMINAL
G
Fig.2
1-12 (No.YA067)
Page 13
3.1.5 REMOVING THE AV TERMINAL BOARD (Fig.3)
• Remove the AV TERMINAL. (1) Remove the 12 screws [F] (2) Remove the AV terminal board.
3.1.6 REMOVING THE PC TERMINAL BOARD (Fig.3)
• Remove the PC TERMINAL. (1) Remove the 4 screws [H]. (2) Remove the 4 screws [I] with a box wrench. (3) Remove the PC terminal board.
3.1.7 REMOVING THE SHEELD COVER (Fig.4)
• Remove the HANDLE.
• Remove the REAR COVER. (1) Remove the 7 screws [J]. (2) Pull up the SHIELD COVER.
3.1.8 REMOVING THE CHASSIS FRAME (Fig.4)
• Remove the HANDLE.
• Remove the REAR COVER. (1) Remove the 4 screws [K]. (2) Remove the CHASSIS FRAME.
AV TERMINAL PWB
SHIELD
J
COVER
PC TERMINAL PWB
H
I
F
Fig.3
K
CHASSIS
FRAME
J
3.1.9 REMOVING THE BATTERY PWB (Fig.5)
• Remove the AV TERMINAL. (1) Remove the 1 screw [L]. (2) Remove the CND connector. (3) Pull the BATTERY PWB toward you, and remove it.
Fig.4
AV TERMINAL
BATTERY PWB
CND connector
L
Fig.5
(No.YA067)1-13
Page 14
3.1.10 REMOVING THE MAIN PWB (Fig.6)
• Remove the HANDLE.
• Remove the REAR COVER.
• Remove the AV TERMINAL.
• Remove the PC TERMINAL.
• Remove the SHIELD COVER.
• Remove the CHASSIS FRAME.
• Remove the BATTERY PWB. (1) Remove the 7 screws [M]. (2) Remove the CNA
the MAIN PWB.
(3) Remove the CN1006
MAIN PWB and DIGITAL PWB.
3.1.11 REMOVING THE DIGITAL PWB (Fig.6)
• Remove the HANDLE.
• Remove the REAR COVER.
• Remove the AV TERMINAL.
• Remove the PC TERMINAL.
• Remove the SHIELD COVER.
• Remove the CHASSIS FRAME.
• Remove the BATTERY PWB.
• Remove the MAIN PWB. (1) Remove the 4 screws [N]. (2) Remove the connector CNP (3) Remove the DIGITAL PWB.
/ CNF / CNQ / CNT / CNX connector on
connector which has connected
/ CN2002 connector.
DIGITAL
PWB
N
Fig.6
M
MAIN PWB
3.1.12 REMOVING THE LINE FILTER PWB (Fig.7)
• Remove the HANDLE.
• Remove the REAR COVER.
• Remove the AV TERMINAL.
• Remove the PC TERMINAL.
• Remove the SHIELD COVER.
• Remove the CHASSIS FRAME. (1) Remove the 4 screws [O], and remove the FILTER
SHIELD. (2) Remove the 4 screws [P]. (3) Remove the 1 screws [Q]. (4) Remove the CN8001
SUPPLY UNIT. (5) Lift up the LINE FILTER PWB and remove. (6) Remove the LF INSULATOR under the LINE FILTER
PWB.
3.1.13 REMOVING THE CHASSIS BASE (Fig.7)
• Remove the HANDLE.
• Remove the REAR COVER.
• Remove the AV TERMINAL.
• Remove the PC TERMINAL.
• Remove the SHIELD COVER.
• Remove the CHASSIS FRAME.
• Remove the LINE FILTER PWB. (1) Remove the 2 screws [R]. (2) Remove the 3 screws [S]. (3) Lift the CHASSIS BASE and remove it.
NOTE:
CHASSIS BASE can be removed where an MAIN BOARD, DIGITAL BOARD and a LINE FILTER PWB are attached.
connector on the MAIN POWER
O
P
LF INSULATOR
S
FILTER SHIELD
LINE FILTER PWB
S
Q
EARTH
WIRE
R
CHASSIS BASE
Fig.7
1-14 (No.YA067)
Page 15
3.1.14 REMOVING THE COOLING FAN (FOR PANEL) (Fig.8)
• Remove the REAR COVER (1) Remove the 2 screws [T] (2) Remove the 1 screw [U]. (3) Remove the fan blanket. (4) Remove the CNF1
PWB. (5) Remove the 2 screws [V]. (6) Remove the COOLING FAN (for PANEL).
3.1.15 REMOVING THE SPEAKER TERMINAL PWB (Fig.8)
• Remove the REAR COVER. (1) Remove the 3 screws [W] (2) Remove the 3 screws [X]. (3) Remove the SPEAKER TERMINAL BRACKET. (4) Remove the CN6006
remove the SPEAKER TERMINAL PWB.
/ CNF2 connector on the SUB POWER
/ CN600R / CN600L connector, and
T
FAN
V
BRACKET
3.1.16 REMOVING THE AUDIO PWB (Fig.8)
• Remove the REAR COVER.
• Remove the SPEAKER TERMINAL BRACKET.
• Remove the SPEAKER TERMINAL PWB. (1) Remove the 1 screw [Y]. (2) Remove the CNA (3) Remove the AUDIO PWB.
3.1.17 REMOVING THE SPEAKER (Fig.8)
• Remove the REAR COVER. (1) Remove the 2 screws [a]. (2) Remove the speaker cable. (3) Remove the SPEAKER. (4) Remove the 1 screw [b] (5) Remove the 2 screws [c] (6) Remove the SPEAKER BRACKET.
/ CNB connector.
V
COOLING FAN(For PANEL)
a
U
b
SPEAKER
c
FAN
BRACKET
T
COOLING
FAN(For PANEL)
U
SPEAKER
TERMINAL
PWB
SPEAKER
SPEAKER BRACKET
X
SPEAKER
TERMINAL
W
BRACKET
X
Z
a
AUDIO PWB
AUDIO PWB
BRACKET
Fig.8
(No.YA067)1-15
Page 16
3.1.18 REMOVING THE BACK FRAME (Fig.9)
• Remove the HANDLE.
• Remove the REAR COVER.
• Remove the AV TERMINAL.
• Remove the PC TERMINAL.
• Remove the SHIELD COVER.
• Remove the CHASSIS FRAME.
• Remove the LINE FILTER PWB.
• Remove the CHASSIS BASE.
• Remove the COOLING FAN (For PANEL). (1) Remove the 4 screws [e] (2) Remove the 4 screws [f]. (3) Remove the BACK FRAME. (4) An other side BACK FRAME can also be removed in the
same procedure.
3.1.19 REMOVING THE TEMP. SENSOR 2 PWB. (Fig.10)
• Remove the HANDLE.
• Remove the REAR COVER. (1) Remove the 1 screw [g]. (2) Remove the TEMP. SENSOR 2 PWB.
3.1.20 REMOVING THE BACK FRAME SPACER (Fig.10)
• Remove the HANDLE.
• Remove the REAR COVER.
• Remove the AV TERMINAL.
• Remove the PC TERMINAL.
• Remove the SHIELD COVER.
• Remove the CHASSIS FRAME.
• Remove the LINE FILTER PWB.
• Remove the CHASSIS BASE.
• Remove the COOLING FAN (For PANEL).
• Remove the BACK FRAME.
• Remove the TEMP. SENSOR. (1) Remove the 3 screws [h]. (2) Remove the BACK FRAME SPASER. (3) Four BACK FRAME SPACER can be removed by the
same method.
BACK FRAME
e
f
BACK FRAME
SPACER
h
e
f
Fig.9
TEMP
SENSOR 2
PWB
h
f
BACK FRAME
e
g
h
f
e
BACK FRAME
SPACER
h
1-16 (No.YA067)
Fig.10
Page 17
3.1.21 REMOVING THE SUB POWER PWB (Fig.11)
• Remove the REAR COVER. (1) Remove the 6 screws [i]. (2) Remove the CNB
/ CNR / CNF1 / CNF2 / CNF3 / CNV1 /
CNV2 connectors on the SUB POWER PWB.
(3) Remove the SUB POWER PWB.
3.1.22 REMOVING THE MAIN POWER SUPPLY UNIT (Fig.11)
• Remove the REAR COVER. (1) Remove the 8 screws [j]. (2) Remove the CN805
/ CN806 / CN8009 / CN9001
connector on the MAIN POWER SUPPLY UNIT.
(3) Remove the MAIN POWER SUPPLY UNIT.
3.1.23 REMOVING THE TEMP. SENSOR 1 PWB (Fig.11)
• Remove the REAR COVER. (1) Remove the 1 screw [k]. (2) Remove the TEMP. SENSOR 1 PWB.
3.1.24 REMOVING THE COOLING FAN
(For POWER SUPPLY UNIT) (Fig.11)
• Remove the REAR COVER. (1) Remove the 2 screws [l]. (2) Remove the FAN BRACKET. (3) Remove the 4 screws [m] attaching the COOLING FAN
(For POWER SUPPLY UNIT).
MAIN POWER
SUPPLY UNIT
j
TEMP
SENSOR 1
PWB
k
SUB POWER PWB i
i
COOLING FAN
(For POWER SUPPLY)
l
m
FAN
BRACKET
Fig.11
3.1.25 REMOVING THE CHASSIS BASE FOR POWER SUPPLY PART (Fig.12)
• Remove the HANDLE.
• Remove the REAR COVER.
• Remove the AV TERMINAL.
• Remove the PC TERMINAL.
• Remove the SHIELD COVER.
• Remove the CHASSIS FRAME.
• Remove the MAIN PWB.
• Remove the DIGITAL PWB.
• Remove the LINE FILTER PWB.
• Remove the CHASSIS BASE.
• Remove the COOLING FAN (For PANEL).
• Remove the BACK FRAME.
• Remove the TEMP. SENSOR.
• Remove the SUB POWER PWB.
CHASSIS BASE FOR POWER SUPPLY PART
• Remove the MAIN POWER SUPPLY UNIT. (1) Remove the 5 screws [n]. (2) Remove the CHASSIS BASE FOR POWER SUPPLY
PART.
n
Fig.12
(No.YA067)1-17
Page 18
3.1.26 REMOVING THE PDP UNIT (Fig.13)
• Remove the HANDLE.
• Remove the REAR COVER.
• Remove the AV TERMINAL.
• Remove the PC TERMINAL.
• Remove the CHASSIS FRAME.
• Remove the MAIN PWB.
• Remove the DIGITAL PWB.
• Remove the LINE FILTER PWB.
• Remove the CHASSIS BASE.
• Remove the COOLING FAN (For PANEL).
• Remove the BACK FRAME.
• Remove the TEMP. SENSOR.
• Remove the SUB POWER PWB.
• Remove the MAIN POWER SUPPLY UNIT.
• Remove the CHASSIS BASE OF POWER SUPPLY PART. (1) Remove the 4 screws [o]. (2) Holding the BACK FRAME SPASER, and lift the PDP UNIT
upright and remove it.
3.1.27 REMOVING THE FRONT PANEL (Fig.14)
• Remove the REAR COVER. (1) Remove the 4 screws [p]. (2) Lift the PDP UNIT, and remove the FRONT PANEL.
3.1.28 REMOVING THE CONTROL PWB (Fig.14)
• Remove the REAR COVER.
• Remove the FRONT PANEL. (1) Remove the 3 screws [q]. (2) Remove the CONTROL PWB.
3.1.29 REMOVING THE CONTROL PWB (Fig.14)
• Remove the REAR COVER.
• Remove the FRONT PANEL. (1) Remove the 2 screws [r]. (2) Remove the CONTROL NOB.
O
BACK FRAME
SPACER
FRONT
PANEL
PDPUNIT
p
BACK FRAME
SPACER
FRONT PANEL
Fig.13
LED
PWB
s
3.1.30 REMOVING THE LED PWB (Fig.14)
• Remove the REAR COVER.
• Remove the FRONT PANEL. (1) Remove the 2 screws [s]. (2) Remove the LED PWB.
1-18 (No.YA067)
FRONT CONTROL
PWB
q
Fig.14
r
CONTROL NOB
Page 19
3.2 REMOVING THE PDP UNIT
3.2.1 REMOVING THE X LEFT TOP PWB (Fig.15)
• Remove the PDP UNIT (1) Remove the [P4
connector on the X LEFT TOP PWB. (2) Remove the 2 screws [e] and 1 screws [f]. (3) Remove the X LEFT TOP PWB.
NOTE:
• It will be useful if a note of the connection place (number of
a connector) of the removed connector is made.
3.2.2 REMOVING THE X CENTER TOP PWB (Fig.15)
• Remove the PDP UNIT (1) Remove the [P5
[P507] / [P508] connector on the X CENTER TOP PWB.
(2) Remove the 1 screw [f] and 2 screws [g] X CENTER TOP
PWB.
NOTE:
• It will be useful if a note of the connection place (number of
a connector) of the removed connector is made.
3.2.3 REMOVING THE RIGHT TOP PWB (Fig.15)
• Remove the PDP UNIT (1) Remove the [P1
connector X RIGHT TOP on the PWB. (2) Remove the 2 screws [h]. (3) Remove the X RIGHT TOP PWB.
NOTE:
• It will be useful if a note of the connection place (number of
a connector) of the removed connector is made.
3.2.4 REMOVING THE Z SUS PWB (Fig.15)
• Remove the PDP UNIT (1) Remove the [P1
connectors on the Z SUS PWB. (2) Remove the 9 screws [i]. (3) Remove the Z SUS PWB.
NOTE:
• It will be useful if a note of the connection place (number of
a connector) of the removed connector is made.
3.2.5 REMOVING THE DC/DC PWB (Fig.15)
• Remove the PDP UNIT (1) Remove the [P21
connector on the DC/DC PWB. (2) Remove the 4 screws [j]. (3) Remove the DC/DC PWB.
NOTE:
• It will be useful if a note of the connection place (number of
a connector) of the removed connector is made.
3.2.6 REMOVING THE LVDS CONTROL PWB (Fig.15)
• Remove the PDP UNIT (1) Remove the [P2
] / [P106] / [P200] / [P201] / [P300] connector on the
[P105
LVDS CTRL PWB. (2) Remove the 4 screws [k]. (3) Remove the LVDS CONTROL PWB.
NOTE:
• It will be useful if a note of the connection place (number of
a connector) of the removed connector is made.
3.2.7 REMOVING THE TEMP SENSOR PWB (Fig.15)
• Remove the PDP UNIT (1) Remove the [P2 (2) Remove the 2 screws [m].
] / [P5] / [P501] / [P502] / [P503] / [P504]
] / [P6] / [P10] / [P100] / [P505] / [P506] /
] / [P4] / [P5] / [P6] / [P509] /[P510] / [P511]
] / [P2] / [P3] / [P5] / [P6] / [P9] / [P12]
] / [P22] / [P23] / [P24] / [P25] / [P26]
] / [P3] / [P101] / [P102] / [P103]/ [P104] /
] connector on the LVDS CONTROL PWB.
(3) Remove the TEMP SENSOR PWB.
NOTE:
• It will be useful if a note of the connection place (number of a connector) of the removed connector is made.
3.2.8 REMOVING THE Y SUS PWB (Fig.15)
• Remove the PDP UNIT (1) Remove the [P2
] / [P11] connector on the Y SUS PWB.
/ [P10 (2) Remove the 8 screws [n]. (3) Remove the Y SUS PWB.
NOTE:
• It will be useful if a note of the connection place (number of
a connector) of the removed connector is made.
3.2.9 REMOVING THE Y DRV UPPER PWB (Fig.15)
• Remove the PDP UNIT (1) Remove the [P9 (2) Remove the [P6
connector on the Y DRV UPPER PWB. (3) Remove the 4 screws [o]. (4) Remove the Y DRIVE UPPER PWB.
NOTE:
• It will be useful if a note of the connection place (number of
a connector) of the removed connector is made.
3.2.10 REMOVING THE Y DRV LOWER PWB (Fig.15)
• Remove the PDP UNIT (1) Remove the [P2 (2) Remove the [P1
on the Y DRV LOWER PWB. (3) Remove the 4 screws [P]. (4) Remove the Y DRIVE LOWER PWB.
NOTE:
• It will be useful if a note of the connection place (number of
a connector) of the removed connector is made.
3.2.11 REMOVING THE X RIGHT BOTTOM PWB (Fig.15)
• Remove the PDP UNIT (1) Remove the [P2
connector on the X RIGHT BOTTOM. (2) Remove the 2 screws [q]. (3) Remove the X RIGHT BOTTOM PWB.
NOTE:
• It will be useful if a note of the connection place (number of
a connector) of the removed connector is made.
3.2.12 REMOVING THE X CENTER BOT-TOM PWB (Fig.15)
• Remove the PDP UNIT (1) Remove the [P1
] / [P425] connectors on the X CENTER BOTTOM.
[P408 (2) Remove the 2 screws [r] and 1 screws [s]. (3) Remove the X CENTER BOT-TOM PWB.
NOTE:
• It will be useful if a note of the connection place (number of
a connector) of the removed connector is made.
3.2.13 REMOVING THE X CENTER BOT-TOM PWB (Fig.15)
• Remove the PDP UNIT (1) Remove the [P1
connector on the X LEFT BOTTOM PWB. (2) Remove the 1 screw [s] and 2 screws [t]. (3) Remove the X LEFT BOTTOM PWB.
NOTE:
• It will be useful if a note of the connection place (number of
a connector) of the removed connector is made.
] / [P3] / [P4] / [P5] / [P6] / [P7] / [P8] /[P9]
] / [P10] connector on the Y SUB PWB.
] / [P7] / [P8] / [P10] / [P12] / [P13]
] / [P10] connector on the Y SUB PWB. ] / [P2] / [P3] / [P4] / [P5] / [P11] connector
] / [P3] / [P7] / [P401] / [P402] / [P403]
] / [P4] / [P7] / [P405] /[P406] / [P407] /
] / [P2] / [P401] / [P402] / [P403] / [P404]
(No.YA067)1-19
Page 20
DC/DC PWB
X CENTER TOP PWBX LEFT TOP PWB
X RIGHT TOP PWB
(x2)
Y DRIVE UPPER
PWB
Y SUS PWB
(x8)
Y DRIVE LOWER
PWB
m
(x2)
(x2)
X LEFT BOTTOM PWB
e
(x2)
f
j
(x4)
g
(x2)
h
(x2)
o
i
(x9)
Z SUS PWB
n
p
t
(x2) (x4)
s k
(x2)
r
q
(x2)
X CENTER BOTTOM PWB
TEMP SENSOR PWB
X RIGHT BOTTOM PWB
LVDS CONTROL PWB
1-20 (No.YA067)
Fig.15
Page 21
3.3 REPLACEMENT OF MEMORY ICs
3.3.1 MEMORY IC
This model uses memory IC. In the memory IC is memorized data for correctly operating the video and drive circuits. When replacing the memory IC, be sure to use IC written with the initial values of data.
3.3.2 PROCEDURE FOR REPLACING MEMORY IC
(1) Power off
Switch the power off and unplug the power plug from the wall outlet.
(2) Replace IC
Be sure to use memory IC written with the initial data values.
(3) Power on
Connect the power plug into the wall outlet and turn the power on.
3.3.3 PROCEDURE FOR SET-UP MENU
(1) Press the [MENU / EXIT] key and the [VOLUME-] key
simultaneously. (2) The SET-UP MENU screen (Fig. 1) will be displayed. (3) Check the setting value of the SET-UP MENU table. (Refer
to the next page.) (4) If the value is different, select the setting item with the
SELECT [/] key, and set the correct value with the
ADJUST [/] key. (5) Press the [MENU / EXIT] key, and return to the normal
screen.
3.3.4 PROCEDURE FOR reset OR all reset
(1) The SET-UP MENU is displayed. (2) Select "reset" or "all reset" item with SELECT [/] key of
remote control unit. (3) Press ENTER [] key, and the "reset" (or all reset) menu is
displayed (Fig. 2). (4) Press ENTER [] key to "reset" the standard settings.
< SET-UP MENU >
STATUS DISPLAY CONTROL LOCK REMOTE SWITCH HD SIGNAL MODE WHITE BALANCE TIMER
ADJUST: SELECT: EXIT:
< SET-UP MENU > 2/2
PIXEL SHIFT POWER SAVE COLOR-REVERSE REFRESH reset all reset HOUR METER x100h MODEL NAME : GM-V42
ADJUST: SELECT: EXIT:
: ON : OFF : MODE1 : 1080i
: OFF : OFF : OFF : OFF
: 000
1/2
MENU
MENU
SET-UP MENUscreen
When select the [reset or all reset] change to [ENTER : ] mode.
Fig.1
or <reset>
< all reset >
Are you sure
"YES" then Key. "NO" then Key.
MENU
[reset] / [all reset]
Fig.2
REMOTE CONTROL UNIT KEY ASSIGNMENT
MENU/EXIT
key
RM-C579 REMOTE CONTROL UNIT
POWER
OFF ON
DISPLAY
INPUT SELECT
A
VIDEO
MUTING
MENU/EXIT
VOLUME
ASPECT
COMPO.
/(RGB B)
RGB AB
VOLUME key
(-/+)
SELECT key
( )
ENTER key ( )
ADJUST key
( )
(No.YA067)1-21
Page 22
INITIAL SETTING FACTORY SHIPPING
Setting item Setting value Setting item Setting value
POWER OFF VOLUME 10 INPUT SELECT VIDEO A
MAIN MENU
PICTURE ADJ. CONTRAST 10 SIZE/POSITION ADJ. V POSITION 00
BRIGHT 00 DOT CLOCK (RGB only) 00 CHROMA 00 CLOCK PHASE (RGB only) 00 PHASE 00 FUNCTION SELECT COLOR TEMP HIGH SHARPNESS 00 ASPECT REGULAR
SIZE/POSITION ADJ. H SIZE 00 SIGNAL MODE AUTO
H POSITION 00 RGB / COMP. COMP. V SIZE 00 SYNC TERM HIGH
SETUP MENU STATUS DISPLAY ON REMOTE SWITCH MODE1 CONTROL LOCK OFF HD SIGNAL MODE 1080i FAN SPEED LOW COLOR-REVERSE COLOR-REVERSE OFF WHITE BALNCE HIGH R GAIN Set MAX at
G GAIN START TIME - - : - ­B GAIN END SET OFF
LOW R GAIN Set MAX at
G GAIN REFRESH REFRESH OFF B GAIN START SET OFF
TIMER PRESENT TIME - - : - - START TIME - - : - -
POWER-ON SET OFF END SET OFF POWER-ON TIME - - : - - END TIME - - : - ­POWER-OFF SET OFF MODEL NAME GM-X50
POWER-OFF TIME - - : - ­PIXEL SHIFT OFF POWER SAVE OFF
least one item. (other is 0)
least one item. (other is 0)
START SET OFF
END TIME - - : - -
SERVICE SETTING ITEMS
Setting item Contents Setting item Contents
VCO ADJUST Video decorder VCO adjustment SIGNAL BLOCK Signal circuit adjustment WHITE BALANCE BLOCK WHITE BALANCE adjustment DEVICE INITIAL VALUE Initial setting of DEVICE CPU BLOCK Setting of CPU DIAGNOSIS BLOCK DIAGNOSIS function SIZE/POSITION BLOCK SIZE/POSITION adjustment UP DATE CPU PROGRAM Up date of CPU PROGRAM H. POSITION BLOCK H. POSITION adjustment HOUR METER BLOCK HOUR METER function PANEL BLOCK Setting of PDP (panel) ENHANCER BLOCK Sharpness circuit adjustment
1-22 (No.YA067)
Page 23
3.4 REPLACEMENT OF CHIP COMPONENT
3.4.1 CAUTIONS
(1) Avoid heating for more than 3 seconds. (2) Do not rub the electrodes and the resist parts of the pattern. (3) When removing a chip part, melt the solder adequately. (4) Do not reuse a chip part after removing it.
3.4.2 SOLDERING IRON
(1) Use a high insulation soldering iron with a thin pointed end of it. (2) A 30w soldering iron is recommended for easily removing parts.
3.4.3 REPLACEMENT STEPS
1. How to remove Chip parts
2. How to install Chip parts
[Resistors, capacitors, etc.]
(1) As shown in the figure, push the part with tweezers and
alternately melt the solder at each end.
(2) Shift with the tweezers and remove the chip part.
[Transistors, diodes, variable resistors, etc.]
(1) Apply extra solder to each lead.
SOLDER
SOLDER
[Resistors, capacitors, etc.]
(1) Apply solder to the pattern as indicated in the figure.
(2) Grasp the chip part with tweezers and place it on the
solder. Then heat and melt the solder at both ends of the chip part.
[Transistors, diodes, variable resistors, etc.]
(1) Apply solder to the pattern as indicated in the figure. (2) Grasp the chip part with tweezers and place it on the
solder.
(3) First solder lead A as indicated in the figure.
(2) As shown in the figure, push the part with tweezers and
alternately melt the solder at each lead. Shift and remove the chip part.
NOTE :
After removing the part, remove remaining solder from the pattern.
A
B
C
(4) Then solder leads B and C.
A
B
C
(No.YA067)1-23
Page 24
SECTION 4
ADJUSTMENT
4.1 BEFORE ADJUSTMENT
(1) There are 2 ways of adjusting this monitor : One is with the
REMOTE CONTROL UNIT and the other is the conventional method using adjustment parts and components.
(2) The setting (adjustment) using the REMOTE CONTROL
UNIT is made on the basis of the initial setting values. The setting values which adjust the screen to the optimum condition can be different from the initial setting values.
(3) Make sure that connection is correctly made to AC power
source.
(4) Turn on the power of the Plasma display monitor and
measuring instrument for warming up for at least 30 minutes before starting adjustment.
(5) If the input signal is not specified, use the most appropriate
signal for adjustment.
(6) Never touch parts (such as variable resistors, transformers
and condensers) not shown in the adjustment items of this service adjustment.
4.2 MEASURING INSTRUMENT AND TOOLS
• DC voltmeter (or digital voltmeter)
• Oscilloscope
• Colour analyzer (colour temperature meter)
• Signal generator
- Colour bar : PAL / SECAM / NTSC
- Whale black pattern : 480i, 1080i
- Lamp pattern :
NTSC / 480i / 1080i / VGA640 × 480 dots (H fr 31.5kHz, V fr 60Hz) / RGB 15k (H fr 15.73kHz, V fr 59.94Hz)
- Window pattern :
NTSC /480i / 1080i / VGA640 × 480 dots (H fr 31.5kHz, V fr 60Hz) / RGB 15k (H fr 15.73kHz, V fr 59.94Hz)
- Gray scall pattern :
NTSC/480i / 1080i / VGA640 × 480 dots (H fr 31.5kHz, V fr 60Hz) / RGB 15k (H fr 15.73kHz, V fr 59.94Hz)
• Remote control unit
4.3 PROCEDURE FOR SERVICE MODE
4.3.1 HOW TO ENTER THE SERVICE MODE
(1) Press the [MENU] key, and SELECT [] key
simultaneously (Fig. 1).
(2) The " " mark is appears at the center of the screen (Fig.
2).
(3) While " " mark is appears, press the [MENU] key and
[VOL-] key simultaneously.
(4) The word "PLEASE DON'T TOUCH !" (Fig.3) will be
display on the screen center.
(5) While the words of "PLEASE DON'T TOUCH !" are display
as shown in Fig. 3.
(6) Press the SELECT [] key, SERVICE MODE will be
display as shown in Fig. 4.
4.3.2 SELECT & ADJUSTMENT OF SERVICE MODE ITEM
While the SERVICE MODE is displayed.
(1) Press the up [/] select key to white balance block item. (2) After selecting the item, press ENTER [] key. (3) The adjustment menu mode is displayed. (4) Press the ADJUST [/] key to change the setting value. (5) Press [MENU / EXIT] key to display the original menu. (6) Perform in the same manner for others SERVICE MODE
ITEM.
Note :
When the adjustment is made at SERVICE MODE, the changed data is memorized in a memory simultaneously with the change.
Fig.1
Fig.2
PLEASE, DON'T TOUCH!
Fig.3
VCO ADJUST WHITE BALANCE BLOCK CPU BLOCK SIZE/POSITION BLOCK H POSITION BLOCK PANEL BLOCK SIGNAL BLOCK DEVICE INITIAL VALUE
ENTER: SELECT: EXIT:
DIAGNOSIS BLOCK UPDATE CPU PROGRAM HOUR METER BLOCK ENHANCER BLOCK
ENTER: SELECT: EXIT:
Fig.4
[1/2]
MENU
[2/2]
MENU
1-24 (No.YA067)
Page 25
4.4 COMPOSITION OF A SERVICE MENU SCREEN
MAIN MENU
W(A01)
WHITE BALANCE BLOCK
adjustment item screen
C(A01)
CPU BLOCK
adjustment item screen
VCO ADJUST WHITE BALANCE BLOCK CPU BLOCK SIZE/POSITION BLOCK H POSITION BLOCK PANEL BLOCK SIGNAL BLOCK DEVICE INITIAL VALUE
ENTER: SELECT: EXIT:
< VCO ADJUST PROGRAM >
Are you sure ?
"YES" then Key. "NO" then Key.
MENU
< WHITE BALANCE BLOCK >
WA:RGB PS HIGH WB:RGB PC LOW WC:VIDEO HIGH WD:VIDEO LOW WE:COMPO. 15k HIGH WF:COMPO. 15k LOW WG:COMPO. HIGH WH:COMPO. LOW
ENTER: SELECT: EXIT:
WHITE BALANCE BLOCK
adjustment item select screen
< CPU BLOCK >
CA:PANORAMA DATA CB:SIGNAL RANGE CC:SIZE/POSI. RANGE CD:FRQENCY DATA CE:SYSTEM CONSTANT CF:TEMP SENCOR DATA CG:APS CONTROL DATA CH:TEST MODE
ENTER: SELECT: EXIT:
CPU BLOCK
adjustment item select screen
< SIZE/POSITION BLOCK >
DA:VIDEO-60Hz (REGULAR) DB:VIDEO-60Hz (FULL) DC:VIDEO-60Hz (ZOOM) DD:VIDEO-60Hz (PANORA.) DE:VIDEO-50Hz (REGULAR) DF:VIDEO-50Hz (FULL) DG:VIDEO-50Hz (ZOOM) DH:VIDEO-50Hz (PANORA.)
ENTER: SELECT: EXIT:
< H POSITION BLOCK >
PA:VIDEO PB:Y/C PC:COMPO. PD:RGB
ENTER: SELECT: EXIT:
MENU
MENU
MENU
MENU
MENU
[2/2]
MENU
MENU
MENU
MENU
DIAGNOSIS BLOCK
< CLEAR >
Are you sure ?
"YES" then Key. "NO" then Key.
MENU
Flashing 5 sec.
[1/2]
MENU
DIAGNOSIS BLOCK UPDATE CPU PROGRAM HOUR METER BLOCK ENHANCER BLOCK
ENTER: SELECT: EXIT:
< DIAGNOSIS BLOCK >
CLEAR I2C SIGNAL BUS I2C ROM BUS FAN STOP POWER TEMP OVER TEMP. OVER(90h) TEMP. OVER(92h) TEMP. OVER(94h)
ENTER: EXIT:
< DIAGNOSIS BLOCK >
CLEAR I2C SIGNAL BUS I2C ROM BUS FAN STOP POWER TEMP OVER TEMP. OVER(90h) TEMP. OVER(92h) TEMP. OVER(94h)
ENTER: EXIT:
< UPDATE CPU PROGRAM >
Are you sure ?
"YES" then Key. "NO" then Key.
Necessity ! : PC, cable & terminal software
CURRENT Ver. 1.02
< HOUR METER BLOCK >
RESET HOUR METER (X1h) : *****
ENTER: EXIT:
< PANEL BLOCK >
BA:VIDEO BB:COMP.HD BC:PC
ENTER: SELECT: EXIT:
< SIGNAL BLOCK >
SA:VIDEO -NTSC SB:VIDEO -PAL SC:VIDEO -SECAM SD:VIDEO -NTSC4.43 SE:VIDEO -PALM SF:VIDEO -PALN SG:VIDEO -PAL-60 SH:Y/C -NTSC
ENTER: SELECT: EXIT:
< DEVICE INITIAL VALUE >
IA:VPC3230D IB:CXA3516R IC:TA1318 ID:PEMBRANDT-I IE:PDP I/F IF:JCC5054(DSD) IG:UPD64083GF
ENTER: SELECT: EXIT:
MENU
MENU
MENU
< HOUR METER BLOCK >
RESET HOUR METER (X1h) : 00000
ENTER: EXIT:
< ENHANCER BLOCK >
EA:VIDEO EB:COMPO.SD EC:COMPO.HD ED:RGB-L EE:RGB-M EF:RGB-H
ENTER: SELECT: EXIT:
< RESET HOUR METER >
! Are you sure ?
"YES" then Key. "NO" then Key.
MENU
MENU
MENU
(No.YA067)1-25
Page 26
4.5 INITIAL SETTING VALUE OF THE SERVICE MENU
WHITE BALANCE BLOCK
Setting No. Setting item
WA:RGB PC HIGH W(A01) DRIVE(R) 255 W(A02) DRIVE(G) 255 W(A03) DRIVE(B) 255 W(A04) CUTOFF(R) 124 W(A05) CUTOFF(G) 124 W(A06) CUTOFF(B) 124 W(A07) BRIGHT 128 W(A08) AD GAIN(R) 128 W(A09) AD GAIN(G) 128 W(A10) AD GAIN(B) 128 W(A11) AD OFFSET(R) 128 W(A12) AD OFFSET(G) 128 W(A13) AD OFFSET(B) 128 WB:RGB PC LOW W(B01) DRIVE(R) 255 W(B02) DRIVE(G) 255 W(B03) DRIVE(B) 200 W(B04) CUTOFF(R) 128 W(B05) CUTOFF(G) 128 W(B06) CUTOFF(B) 128 W(B07) BRIGHT 128 W(B08) AD GAIN(R) 128 W(B09) AD GAIN(G) 128 W(B10) AD GAIN(B) 128 W(B11) AD OFFSET(R) 128 W(B12) AD OFFSET(G) 128 W(B13) AD OFFSET(B) 128 WC:VIDEO HIGH W(C01) DRIVE(R) 255 W(C02) DRIVE(G) 255 W(C03) DRIVE(B) 255 W(C04) CUTOFF(R) 125 W(C05) CUTOFF(G) 124 W(C06) CUTOFF(B) 125 W(C07) BRIGHT 117 WD:VIDEO LOW W(D01) DRIVE(R) 255 W(D02) DRIVE(G) 255 W(D03) DRIVE(B) 200 W(D04) CUTOFF(R) 128 W(D05) CUTOFF(G) 128 W(D06) CUTOFF(B) 128 W(D07) BRIGHT 128 WE:COMPO 15k HIGH W(E01) DRIVE(R) 255 W(E02) DRIVE(G) 255 W(E03) DRIVE(B) 255 W(E04) CUTOFF(R) 126 W(E05) CUTOFF(G) 124 W(E06) CUTOFF(B) 126 W(E07) BRIGHT 128 W(E08) AD GAIN(Pr) 128
1-26 (No.YA067)
Setting
value
Setting No. Setting item
W(E09) AD GAIN(Y) 128 W(E10) AD GAIN(Pb) 128 W(E11) AD OFFSET(Pr) 134 W(E12) AD OFFSET(Y) 128 W(E13) AD OFFSET(Pb) 134 COMPO. 15k LOW W(F01) DRIVE(R) 255 W(F02) DRIVE(G) 255 W(F03) DRIVE(B) 200 W(F04) CUTOFF(R) 128 W(F05) CUTOFF(G) 128 W(F06) CUTOFF(B) 128 W(F07) BRIGHT 128 W(F08) AD GAIN(Pr) 128 W(F09) AD GAIN(Y) 128 W(F10) AD GAIN(Pb) 128 W(F11) AD OFFSET(Pr) 128 W(F12) AD OFFSET(Y) 128 W(F13) AD OFFSET(Pb) 128 WG:COMPO HIGH W(G01) DRIVE(R) 255 W(G02) DRIVE(G) 255 W(G03) DRIVE(B) 255 W(G04) CUTOFF(R) 125 W(G05) CUTOFF(G) 124 W(G06) CUTOFF(B) 125 W(G07) BRIGHT 128 W(G08) AD GAIN(Pr) 128 W(G09) AD GAIN(Y) 128 W(G10) AD GAIN(Pb) 128 W(G11) AD OFFSET(Pr) 134 W(G12) AD OFFSET(Y) 128 W(G13) AD OFFSET(Pb) 134 WH:COMPO LOW W(H01) DRIVE(R) 255 W(H02) DRIVE(G) 255 W(H03) DRIVE(B) 200 W(H04) CUTOFF(R) 128 W(H05) CUTOFF(G) 128 W(H06) CUTOFF(B) 128 W(H07) BRIGHT 128 W(H08) AD GAIN(Pr) 128 W(H09) AD GAIN(Y) 128 W(H10) AD GAIN(Pb) 128 W(H11) AD OFFSET(Pr) 128 W(H12) AD OFFSET(Y) 128 W(H13) AD OFFSET(Pb) 128 WI:RGB 15k HIGH W(I01) DRIVE(R) 255 W(I02) DRIVE(G) 255 W(I03) DRIVE(B) 255 W(I04) CUTOFF(R) 124 W(I05) CUTOFF(G) 124
Setting
value
Page 27
Setting No. Setting item
W(I06) CUTOFF(B) 124 W(I07) BRIGHT 128 W(I08) AD GAIN(R) 125 W(I09) AD GAIN(G) 128 W(I10) AD GAIN(B) 128 W(I11) AD OFFSET(R) 128 W(I12) AD OFFSET(G) 128 W(I13) AD OFFSET(B) 128 WJ:RGB 15k LOW W(J01) DRIVE(R) 255 W(J02) DRIVE(G) 255 W(J03) DRIVE(B) 200 W(J04) CUTOFF(R) 128 W(J05) CUTOFF(G) 128 W(J06) CUTOFF(B) 128 W(J07) BRIGHT 128 W(J08) AD GAIN(R) 128 W(J09) AD GAIN(G) 128 W(J10) AD GAIN(B) 128 W(J11) AD OFFSET(R) 128 W(J12) AD OFFSET(G) 128 W(J13) AD OFFSET(B) 128
Setting
value
(No.YA067)1-27
Page 28
CPU BLOCK
Setting No. Setting item
CA:PANORAMA DATA C(A01) INPUT_PIXELS 77 C(A02) OUTPUT_PIXELS 172 C(A03) NL_START 84 C(A04) NL_END 88 C(A05) RATIO_CENTER 127 C(A06) RATIO_SIDES 168 C(A07) NOT USED 0 C(A08) NOT USED 0 C(A09) NOT USED 0 C(A10) NOT USED 0 CB:SIGNAL RANGE C(B01) CONTRAST(min.) 84 C(B02) CONTRAST(max.) 148 C(B03) BRIGHT(min.) 112 C(B04) BRIGHT(max.) 140 C(B05) CHROMA(min.) 57 C(B06) CHROMA(max.) 173 C(B07) PHASE(min.) 0 C(B08) PHASE(max.) 0 C(B09) NOT USED 0 C(B10) GRAPHIC BRIGHT GAIN
COMPENSATION C(B11) R GAIN(min.) 0 C(B12) R GAIN(max.) 255 C(B13) G GAIN(min.) 0 C(B14) G GAIN(max.) 255 C(B15) B GAIN(min.) 0 C(B16) B GAIN(max.) 255 C(B17) NOT USED 0 C(B18) NOT USED 0 C(B19) NOT USED 0 C(B20) NOT USED 0 CC:SIZE/POSI.RANGE C(C01) H POSITION(min.) 195 C(C02) H POSITION(max.) 60 C(C03) V POSITION(min.) 225 C(C04) V POSITION(max.) 30 C(C05) H SIZE(min.) 155 C(C06) H SIZE(max.) 100 C(C07) V SIZE(min.) 155 C(C08) V SIZE(max.) 100 C(C09) SAMPLING PIXELS(min.) 245 C(C10) SAMPLING PIXELS(max.) 10 C(C11) SAMPLING PHASE(min.) 235 C(C12) SAMPLING PHASE(max.) 20 C(C13) NOT USED 0 C(C14) NOT USED 0 C(C15) NOT USED 0 C(C16) H POSITION(min.) 200 C(C17) H POSITION(max.) 55 C(C18) V POSITION(min.) 225 C(C19) V POSITION(max.) 30 C(C20) H SIZE(min.) 195
Setting
value
255
Setting No. Setting item
C(C21) H SIZE(max.) 60 C(C22) V SIZE(min.) 195 C(C23) V SIZE(max.) 60 C(C24) H POSITION(min.) 200 C(C25) H POSITION(max.) 55 C(C26) V POSITION(min.) 247 C(C27) V POSITION(max.) 30 C(C28) NOT USED 0 C(C29) NOT USED 0 C(C30) NOT USED 0 C(C31) NOT USED 0 C(C32) ENFORCED FREE RUNNING MODE 0 C(C33) PANEL AV/PC MODE for 60Hz 0 C(C34) PANEL AV/PC MODE for 50Hz 0 C(C35) NOT USED 0 C(C36) NOT USED 0 C(C37) NOT USED 0 C(C38) NOT USED 0 C(C39) NOT USED 0 C(C40) NOT USED 0 C(C41) NOT USED 0 C(C42) NOT USED 0 C(C43) NOT USED 0 C(C44) NOT USED 0 C(C45) NOT USED 0 C(C46) NOT USED 0 C(C47) NOT USED 0 C(C48) NOT USED 0 C(C49) NOT USED 0 C(C50) NOT USED 0 C(C51) NOT USED 0 C(C52) NOT USED 0 CD:FREQENCY DATA C(D01) H FREQUENCY ERROR(0.1KHz) 4 C(D02) V FREQUENCY ERROR(1Hz) 1 C(D03) STATUS DISPLAY DELAY 50 C(D04) SIGNAL DETECT 10 C(D05) SIGNAL WAIT TIMER 40 C(D06) SIGNAL WAIT TIMER for US 0 C(D07) NOT USED 0 C(D08) NOT USED 0 C(D09) NOT USED 0 C(D10) NOT USED 0
Setting
value
1-28 (No.YA067)
Page 29
Setting No. Setting item
CE:SYSTEM CONSTANT C(E01) DESTINATION FLAG 2 C(E02) POWER ON DELAY 97 C(E03) POWER OFF DELAY 31 C(E04) MODEL NAME 1 C(E05) REMO-CON THROW 0 C(E06) TIME ERROR COMPENSATION 71 C(E07) VS_MUTE CONTROL 1 C(E08) goalPLC POWER SELECT for 50Hz 128 C(E09) VPC3230D AGC SWITCH 1 C(E10) AC_DET STABILITY 20 C(E11) SUB-POWER ERROR DETECT
TIMER
C(E12) SUB-POWER ERROR DETECT
STABILITY C(E13) NOT USED 0 C(E14) NOT USED 0 C(E15) NOT USED 0 C(E16) NOT USED 0 C(E17) NOT USED 0 C(E18) NOT USED 0 C(E19) NOT USED 0 C(E20) NOT USED 0 DF:TEMP SENSOR DATA C(F01) ALARM TEMP. 72 C(F02) T1 OVER COUNT 60 C(F03) SHUT DOWN TEMP. 120 C(F04) T2 OVER COUNT 60 C(F05) TEMP. ALARM DISPLAY 0 C(F06) T1 ALARM TEMP. 85 C(F07) T11 OVER COUNT 60 C(F08) T11 SHUT DOWN WAIT TIME 12 C(F09) T2 ALARM TEMP 85 C(F10) T21 OVER COUNT 60 C(F11) T21 SHUT DOWN WAIT TIME 12 C(F12) FAN ON/OFF COUNT 6 C(F13) FAN CONTROL MAX. VOLTAGE 33 C(F14) FAN CONTROL MIN. VOLTAGE 23 C(F15) FAN CONTROL MAX. TEMP. 60 C(F16) FAN CONTROL MIN. TEMP. 50 C(F17) FAN OFF TEMP. 10 C(F18) FAN ON TEMP. 15 C(F19) FAN CONTROL INTERVAL 10 C(F20) OFFSET TEMP. for VERTICAL
SETTING C(F21) FAN NORMALY ON 1 C(F22) NOT USED 0 C(F23) NOT USED 0 C(F24) NOT USED 0 C(F25) NOT USED 0 C(F26) NOT USED 0 C(F27) NOT USED 0 C(F28) NOT USED 0 C(F29) NOT USED 0 C(F30) NOT USED 0
Setting
value
31
30
10
Setting No. Setting item
CG:APS CONTROL DATA C(G01) Is COMPENSATION 150 C(G02) Is STANDARD 150 C(G03) TEMP. COMPENSATION STEP 10 C(G04) PLC FIXED VALUE for SAVE2 255 C(G05) AGC ON/OFF 0 C(G06) AGC GAIN MAX. VALUE 0 C(G07) PLC POWER SELECT : k1 15 C(G08) PLC(NORMAL) POWER SELECT : n 128 C(G09) SAMPLING CYCLE SETTING 4 C(G10) STOPPER INTERVAL SETTING 20 C(G11) ANIMATION LUMINOSITY
COMPENSATION C(G12) goalPLC(SAVE1) POWER SELECT : k2 95 C(G13) SAVE1 LOW SETTING 44 C(G14) POWER CONTROL INTERVAL(MAIN) 2 C(G15) POWER CONTROL INTERVAL(SUB) 3 C(G16) POWER CONTROL COEFFICIENT : K 32 C(G17) KX1 25 C(G18) KX2 60 C(G19) KX3 150 C(G20) KYmax0 0 C(G21) KYmax1 22 C(G22) KYmax2 47 C(G23) KYmax3 120 C(G24) KYmax4[7:0] 180 C(G25) KYmin0 12 C(G26) KYmin1 42 C(G27) KYmin2 79 C(G28) KYmin3 160 C(G29) KYmin4[7:0] 210 C(G30) KYmax4[11:8],KYmin4[11:8] 0 C(G31) APS POWER CONTROL TEMP.: T4 64 C(G32) NOT USED 0 C(G33) NOT USED 0 C(G34) NOT USED 0 C(G35) NOT USED 0 C(G36) NOT USED 0 C(G37) NOT USED 0 C(G38) NOT USED 0 C(G39) NOT USED 0 C(G40) NOT USED 0 C(G41) NOT USED 0 C(G42) NOT USED 0 C(G43) NOT USED 0 C(G44) NOT USED 0 C(G45) NOT USED 0 C(G46) NOT USED 0 C(G47) NOT USED 0 C(G48) NOT USED 0 C(G49) NOT USED 0 C(G50) NOT USED 0 CH:TEST MODE C(H01) FPGA TEST MODE 0 C(H02) 480i MATRIX 0
Setting
value
0
(No.YA067)1-29
Page 30
Setting No. Setting item
C(H03) 480p MATRIX 0 C(H04) FREQ. CHECK DISPLAY 0 C(H05) APS CHECK DISPLAY 0 C(H06) D TERMINAL DETECT OFF 0 C(H07) VPC VERSION 0 C(H08) TEST PATERN 0 C(H09) AMDP1plus TEST MODE 16 C(H10) EEPROM VERSION 0 C(H11) NOT USED 0 C(H12) NOT USED 0 C(H13) NOT USED 0 C(H14) NOT USED 0 C(H15) NOT USED 0 C(H16) NOT USED 0 C(H17) NOT USED 0 C(H18) NOT USED 0 C(H19) NOT USED 0 C(H20) NOT USED 0 CI:OTHERS C(I01) PIXEL SHIFT INTERVAL 1 C(I02) PIXEL SHIFT H POSI SHIFT 10 C(I03) PIXEL SHIFT V POSI SHIFT 6 C(I04) RS-232C BAUD RATE 0 C(I05) B GAIN VALUE 195 C(I06) NOT USED 0 C(I07) NOT USED 0 C(I08) NOT USED 0 C(I09) NOT USED 0 C(I10) NOT USED 0
Setting
value
1-30 (No.YA067)
Page 31
SIZE / POSITION BLOCK
Setting No. Setting item
DA:VIDEO 60Hz(REGULAR) D(A01) FB_COUNTER1 172 D(A02) FB_COUNTER2 6 D(A03) VCO_DIVIDE 2 D(A04) DELAY 32 D(A05) CHARGE_PUMP 18 D(A06) AMP MODE 1 D(A07) OUTPUT MODE 6 D(A08) OPLL_MDIV_L 46 D(A09) OPLL_MDIV_H 0 D(A10) OPLL_NDIV 18 D(A11) INPUT_ACT_LINE_START_L 38 D(A12) INPUT_ACT_LINE_START_H 0 D(A13) INPUT_ACT_LINES_L 204 D(A14) INPUT_ACT_LINES_H 1 D(A15) INPUT_ACT_PIXEL_START_L 126 D(A16) INPUT_ACT_PIXEL_START_H 0 D(A17) INPUT_ACT_PIXELS_L 158 D(A18) INPUT_ACT_PIXELS_H 2 D(A19) NOT USED 0 D(A20) NOT USED 0 D(A21) WIN_X_MARGINE 153 D(A22) WIN_Y_MARGINE 146 D(A23) WIN_Y_POSI_L 1 D(A24) WIN_Y_POSI_H 0 D(A25) WIN_Y_SIZE_L 4 D(A26) WIN_Y_SIZE_H 3 D(A27) WIN_X_POSI_L 175 D(A28) WIN_X_POSI_H 0 D(A29) WIN_X_SIZE_L 0 D(A30) WIN_X_SIZE_H 4 D(A31) DS_InX_MARGINE 131 D(A32) DS_OutX_MARGINE 130 D(A33) DS_InY_MARGINE 131 D(A34) DS_OutY_MARGINE 130 D(A35) MARGINE_POS_X 122 D(A36) NOT USED 0 D(A37) NOT USED 0 D(A38) COAST_ENABLE 0 D(A39) NOT USED 0 D(A40) INTERLACE 0 D(A41) DIN_CONTROL_0 4 D(A42) NOT USED 0 D(A43) ahstartL 230 D(A44) ahwidthL 253 D(A45) ahwidth-startH 48 D(A46) VSYNC_CYCLE_L 57 D(A47) VSYNC_CYCLE_H 3 D(A48) NOT USED 0 D(A49) NOT USED 0 D(A50) NOT USED 0 D(A51) NOT USED 0 D(A52) NOT USED 0
Setting
value
Setting No. Setting item
DB:VIDEO 60Hz(FLL) D(B01) FB_COUNTER1 172 D(B02) FB_COUNTER2 6 D(B03) VCO_DIVIDE 2 D(B04) DELAY 32 D(B05) CHARGE_PUMP 18 D(B06) AMP MODE 1 D(B07) OUTPUT MODE 6 D(B08) OPLL_MDIV_L 46 D(B09) OPLL_MDIV_H 0 D(B10) OPLL_NDIV 18 D(B11) INPUT_ACT_LINE_START_L 38 D(B12) INPUT_ACT_LINE_START_H 0 D(B13) INPUT_ACT_LINES_L 204 D(B14) INPUT_ACT_LINES_H 1 D(B15) INPUT_ACT_PIXEL_START_L 124 D(B16) INPUT_ACT_PIXEL_START_H 0 D(B17) INPUT_ACT_PIXELS_L 162 D(B18) INPUT_ACT_PIXELS_H 2 D(B19) NOT USED 0 D(B20) NOT USED 0 D(B21) WIN_X_MARGINE 150 D(B22) WIN_Y_MARGINE 146 D(B23) WIN_Y_POSI_L 1 D(B24) WIN_Y_POSI_H 0 D(B25) WIN_Y_SIZE_L 4 D(B26) WIN_Y_SIZE_H 3 D(B27) WIN_X_POSI_L 1 D(B28) WIN_X_POSI_H 0 D(B29) WIN_X_SIZE_L 94 D(B30) WIN_X_SIZE_H 5 D(B31) DS_InX_MARGINE 131 D(B32) DS_OutX_MARGINE 130 D(B33) DS_InY_MARGINE 131 D(B34) DS_OutY_MARGINE 130 D(B35) MARGINE_POS_X 122 D(B36) NOT USED 0 D(B37) NOT USED 0 D(B38) COAST_ENABLE 0 D(B39) NOT USED 0 D(B40) INTERLACE 0 D(B41) DIN_CONTROL_0 4 D(B42) NOT USED 0 D(B43) ahstartL 0 D(B44) ahwidthL 255 D(B45) ahwidth-startH 240 D(B46) VSYNC_CYCLE_L 57 D(B47) VSYNC_CYCLE_H 3 D(B48) NOT USED 0 D(B49) NOT USED 0 D(B50) NOT USED 0 D(B51) NOT USED 0 D(B52) NOT USED 0
Setting
value
(No.YA067)1-31
Page 32
Setting No. Setting item
DC:VIDEO 60Hz(ZOOM) D(C01) FB_COUNTER1 172 D(C02) FB_COUNTER2 6 D(C03) VCO_DIVIDE 2 D(C04) DELAY 32 D(C05) CHARGE_PUMP 18 D(C06) AMP MODE 1 D(C07) OUTPUT MODE 6 D(C08) OPLL_MDIV_L 46 D(C09) OPLL_MDIV_H 0 D(C10) OPLL_NDIV 18 D(C11) INPUT_ACT_LINE_START_L 97 D(C12) INPUT_ACT_LINE_START_H 0 D(C13) INPUT_ACT_LINES_L 87 D(C14) INPUT_ACT_LINES_H 1 D(C15) INPUT_ACT_PIXEL_START_L 124 D(C16) INPUT_ACT_PIXEL_START_H 0 D(C17) INPUT_ACT_PIXELS_L 162 D(C18) INPUT_ACT_PIXELS_H 2 D(C19) NOT USED 0 D(C20) NOT USED 0 D(C21) WIN_X_MARGINE 150 D(C22) WIN_Y_MARGINE 188 D(C23) WIN_Y_POSI_L 1 D(C24) WIN_Y_POSI_H 0 D(C25) WIN_Y_SIZE_L 4 D(C26) WIN_Y_SIZE_H 3 D(C27) WIN_X_POSI_L 1 D(C28) WIN_X_POSI_H 0 D(C29) WIN_X_SIZE_L 94 D(C30) WIN_X_SIZE_H 5 D(C31) DS_InX_MARGINE 131 D(C32) DS_OutX_MARGINE 130 D(C33) DS_InY_MARGINE 131 D(C34) DS_OutY_MARGINE 130 D(C35) MARGINE_POS_X 122 D(C36) NOT USED 0 D(C37) NOT USED 0 D(C38) COAST_ENABLE 0 D(C39) NOT USED 0 D(C40) INTERLACE 0 D(C41) DIN_CONTROL_0 4 D(C42) NOT USED 0 D(C43) ahstartL 0 D(C44) ahwidthL 255 D(C45) ahwidth-startH 240 D(C46) VSYNC_CYCLE_L 57 D(C47) VSYNC_CYCLE_H 3 D(C48) NOT USED 0 D(C49) NOT USED 0 D(C50) NOT USED 0 D(C51) NOT USED 0 D(C52) NOT USED 0 DD:VIDEO 60Hz(PNORAMIC) D(D01) FB_COUNTER1 172
Setting
value
Setting No. Setting item
D(D02) FB_COUNTER2 6 D(D03) VCO_DIVIDE 2 D(D04) DELAY 32 D(D05) CHARGE_PUMP 18 D(D06) AMP MODE 1 D(D07) OUTPUT MODE 6 D(D08) OPLL_MDIV_L 46 D(D09) OPLL_MDIV_H 0 D(D10) OPLL_NDIV 18 D(D11) INPUT_ACT_LINE_START_L 50 D(D12) INPUT_ACT_LINE_START_H 0 D(D13) INPUT_ACT_LINES_L 180 D(D14) INPUT_ACT_LINES_H 1 D(D15) INPUT_ACT_PIXEL_START_L 125 D(D16) INPUT_ACT_PIXEL_START_H 0 D(D17) INPUT_ACT_PIXELS_L 166 D(D18) INPUT_ACT_PIXELS_H 2 D(D19) DS_OUTX_PANO_L 104 D(D20) DS_OUTX_PANO_H 2 D(D21) WIN_X_MARGINE 150 D(D22) WIN_Y_MARGINE 156 D(D23) WIN_Y_POSI_L 1 D(D24) WIN_Y_POSI_H 0 D(D25) WIN_Y_SIZE_L 4 D(D26) WIN_Y_SIZE_H 3 D(D27) WIN_X_POSI_L 1 D(D28) WIN_X_POSI_H 0 D(D29) WIN_X_SIZE_L 94 D(D30) WIN_X_SIZE_H 5 D(D31) DS_InX_MARGINE 131 D(D32) DS_OutX_MARGINE 130 D(D33) DS_InY_MARGINE 131 D(D34) DS_OutY_MARGINE 130 D(D35) MARGINE_POS_X 122 D(D36) NOT USED 0 D(D37) NOT USED 0 D(D38) COAST_ENABLE 0 D(D39) NOT USED 0 D(D40) INTERLACE 0 D(D41) DIN_CONTROL_0 4 D(D42) NOT USED 0 D(D43) ahstartL 0 D(D44) ahwidthL 255 D(D45) ahwidth-startH 240 D(D46) VSYNC_CYCLE_L 57 D(D47) VSYNC_CYCLE_H 3 D(D48) NOT USED 0 D(D49) NOT USED 0 D(D50) NOT USED 0 D(D51) NOT USED 0 D(D52) NOT USED 0 DE:VIDEO 50Hz(REGULAR) D(E01) FB_COUNTER1 184 D(E02) FB_COUNTER2 6 D(E03) VCO_DIVIDE 2
Setting
value
1-32 (No.YA067)
Page 33
Setting No. Setting item
D(E04) DELAY 32 D(E05) CHARGE_PUMP 18 D(E06) AMP MODE 1 D(E07) OUTPUT MODE 6 D(E08) OPLL_MDIV_L 35 D(E09) OPLL_MDIV_H 0 D(E10) OPLL_NDIV 14 D(E11) INPUT_ACT_LINE_START_L 48 D(E12) INPUT_ACT_LINE_START_H 0 D(E13) INPUT_ACT_LINES_L 32 D(E14) INPUT_ACT_LINES_H 2 D(E15) INPUT_ACT_PIXEL_START_L 131 D(E16) INPUT_ACT_PIXEL_START_H 0 D(E17) INPUT_ACT_PIXELS_L 151 D(E18) INPUT_ACT_PIXELS_H 2 D(E19) NOT USED 0 D(E20) NOT USED 0 D(E21) WIN_X_MARGINE 155 D(E22) WIN_Y_MARGINE 150 D(E23) WIN_Y_POSI_L 1 D(E24) WIN_Y_POSI_H 0 D(E25) WIN_Y_SIZE_L 4 D(E26) WIN_Y_SIZE_H 3 D(E27) WIN_X_POSI_L 175 D(E28) WIN_X_POSI_H 0 D(E29) WIN_X_SIZE_L 0 D(E30) WIN_X_SIZE_H 4 D(E31) DS_InX_MARGINE 131 D(E32) DS_OutX_MARGINE 130 D(E33) DS_InY_MARGINE 131 D(E34) DS_OutY_MARGINE 130 D(E35) MARGINE_POS_X 122 D(E36) NOT USED 0 D(E37) NOT USED 0 D(E38) COAST_ENABLE 0 D(E39) NOT USED 0 D(E40) INTERLACE 0 D(E41) DIN_CONTROL_0 4 D(E42) NOT USED 0 D(E43) ahstartL 230 D(E44) ahwidthL 253 D(E45) ahwidth-startH 48 D(E46) VSYNC_CYCLE_L 192 D(E47) VSYNC_CYCLE_H 3 D(E48) NOT USED 0 D(E49) NOT USED 0 D(E50) NOT USED 0 D(E51) NOT USED 0 D(E52) NOT USED 0 DF:VIDEO 50Hz(FLL) D(F01) FB_COUNTER1 184 D(F02) FB_COUNTER2 6 D(F03) VCO_DIVIDE 2 D(F04) DELAY 32 D(F05) CHARGE_PUMP 18
Setting
value
Setting No. Setting item
D(F06) AMP MODE 1 D(F07) OUTPUT MODE 6 D(F08) OPLL_MDIV_L 35 D(F09) OPLL_MDIV_H 0 D(F10) OPLL_NDIV 14 D(F11) INPUT_ACT_LINE_START_L 48 D(F12) INPUT_ACT_LINE_START_H 0 D(F13) INPUT_ACT_LINES_L 32 D(F14) INPUT_ACT_LINES_H 2 D(F15) INPUT_ACT_PIXEL_START_L 129 D(F16) INPUT_ACT_PIXEL_START_H 0 D(F17) INPUT_ACT_PIXELS_L 156 D(F18) INPUT_ACT_PIXELS_H 2 D(F19) NOT USED 0 D(F20) NOT USED 0 D(F21) WIN_X_MARGINE 156 D(F22) WIN_Y_MARGINE 150 D(F23) WIN_Y_POSI_L 1 D(F24) WIN_Y_POSI_H 0 D(F25) WIN_Y_SIZE_L 4 D(F26) WIN_Y_SIZE_H 3 D(F27) WIN_X_POSI_L 1 D(F28) WIN_X_POSI_H 0 D(F29) WIN_X_SIZE_L 94 D(F30) WIN_X_SIZE_H 5 D(F31) DS_InX_MARGINE 131 D(F32) DS_OutX_MARGINE 130 D(F33) DS_InY_MARGINE 131 D(F34) DS_OutY_MARGINE 130 D(F35) MARGINE_POS_X 122 D(F36) NOT USED 0 D(F37) NOT USED 0 D(F38) COAST_ENABLE 0 D(F39) NOT USED 0 D(F40) INTERLACE 0 D(F41) DIN_CONTROL_0 4 D(F42) NOT USED 0 D(F43) ahstartL 0 D(F44) ahwidthL 255 D(F45) ahwidth-startH 240 D(F46) VSYNC_CYCLE_L 192 D(F47) VSYNC_CYCLE_H 3 D(F48) NOT USED 0 D(F49) NOT USED 0 D(F50) NOT USED 0 D(F51) NOT USED 0 D(F52) NOT USED 0 DG:VIDEO 50Hz(ZOOM) D(G01) FB_COUNTER1 184 D(G02) FB_COUNTER2 6 D(G03) VCO_DIVIDE 2 D(G04) DELAY 32 D(G05) CHARGE_PUMP 18 D(G06) AMP MODE 1 D(G07) OUTPUT MODE 6
Setting
value
(No.YA067)1-33
Page 34
Setting No. Setting item
D(G08) OPLL_MDIV_L 35 D(G09) OPLL_MDIV_H 0 D(G10) OPLL_NDIV 14 D(G11) INPUT_ACT_LINE_START_L 115 D(G12) INPUT_ACT_LINE_START_H 0 D(G13) INPUT_ACT_LINES_L 154 D(G14) INPUT_ACT_LINES_H 1 D(G15) INPUT_ACT_PIXEL_START_L 129 D(G16) INPUT_ACT_PIXEL_START_H 0 D(G17) INPUT_ACT_PIXELS_L 156 D(G18) INPUT_ACT_PIXELS_H 2 D(G19) NOT USED 0 D(G20) NOT USED 0 D(G21) WIN_X_MARGINE 155 D(G22) WIN_Y_MARGINE 188 D(G23) WIN_Y_POSI_L 1 D(G24) WIN_Y_POSI_H 0 D(G25) WIN_Y_SIZE_L 4 D(G26) WIN_Y_SIZE_H 3 D(G27) WIN_X_POSI_L 1 D(G28) WIN_X_POSI_H 0 D(G29) WIN_X_SIZE_L 94 D(G30) WIN_X_SIZE_H 5 D(G31) DS_InX_MARGINE 131 D(G32) DS_OutX_MARGINE 130 D(G33) DS_InY_MARGINE 131 D(G34) DS_OutY_MARGINE 130 D(G35) MARGINE_POS_X 122 D(G36) NOT USED 0 D(G37) NOT USED 0 D(G38) COAST_ENABLE 0 D(G39) NOT USED 0 D(G40) INTERLACE 0 D(G41) DIN_CONTROL_0 4 D(G42) NOT USED 0 D(G43) ahstartL 0 D(G44) ahwidthL 255 D(G45) ahwidth-startH 240 D(G46) VSYNC_CYCLE_L 192 D(G47) VSYNC_CYCLE_H 3 D(G48) NOT USED 0 D(G49) NOT USED 0 D(G50) NOT USED 0 D(G51) NOT USED 0 D(G52) NOT USED 0 DH:VIDEO 50Hz(PANORAMIC) D(H01) FB_COUNTER1 184 D(H02) FB_COUNTER2 6 D(H03) VCO_DIVIDE 2 D(H04) DELAY 32 D(H05) CHARGE_PUMP 18 D(H06) AMP MODE 1 D(H07) OUTPUT MODE 6 D(H08) OPLL_MDIV_L 35 D(H09) OPLL_MDIV_H 0
Setting
value
Setting No. Setting item
D(H10) OPLL_NDIV 14 D(H11) INPUT_ACT_LINE_START_L 62 D(H12) INPUT_ACT_LINE_START_H 0 D(H13) INPUT_ACT_LINES_L 4 D(H14) INPUT_ACT_LINES_H 2 D(H15) INPUT_ACT_PIXEL_START_L 130 D(H16) INPUT_ACT_PIXEL_START_H 0 D(H17) INPUT_ACT_PIXELS_L 160 D(H18) INPUT_ACT_PIXELS_H 2 D(H19) DS_OUTX_PANO_L 104 D(H20) DS_OUTX_PANO_H 2 D(H21) WIN_X_MARGINE 155 D(H22) WIN_Y_MARGINE 164 D(H23) WIN_Y_POSI_L 1 D(H24) WIN_Y_POSI_H 0 D(H25) WIN_Y_SIZE_L 4 D(H26) WIN_Y_SIZE_H 3 D(H27) WIN_X_POSI_L 1 D(H28) WIN_X_POSI_H 0 D(H29) WIN_X_SIZE_L 94 D(H30) WIN_X_SIZE_H 5 D(H31) DS_InX_MARGINE 131 D(H32) DS_OutX_MARGINE 130 D(H33) DS_InY_MARGINE 131 D(H34) DS_OutY_MARGINE 130 D(H35) MARGINE_POS_X 122 D(H36) NOT USED 0 D(H37) NOT USED 0 D(H38) COAST_ENABLE 0 D(H39) NOT USED 0 D(H40) INTERLACE 0 D(H41) DIN_CONTROL_0 4 D(H42) NOT USED 0 D(H43) ahstartL 0 D(H44) ahwidthL 255 D(H45) ahwidth-startH 240 D(H46) VSYNC_CYCLE_L 192 D(H47) VSYNC_CYCLE_H 3 D(H48) NOT USED 0 D(H49) NOT USED 0 D(H50) NOT USED 0 D(H51) NOT USED 0 D(H52) NOT USED 0 DI:480p(REGULAR) D(I01) FB_COUNTER1 82 D(I02) FB_COUNTER2 3 D(I03) VCO_DIVIDE 2 D(I04) DELAY 32 D(I05) CHARGE_PUMP 18 D(I06) AMP MODE 1 D(I07) OUTPUT MODE 2 D(I08) OPLL_MDIV_L 46 D(I09) OPLL_MDIV_H 0 D(I10) OPLL_NDIV 18 D(I11) INPUT_ACT_LINE_START_L 44
Setting
value
1-34 (No.YA067)
Page 35
Setting No. Setting item
D(I12) INPUT_ACT_LINE_START_H 0 D(I13) INPUT_ACT_LINES_L 201 D(I14) INPUT_ACT_LINES_H 1 D(I15) INPUT_ACT_PIXEL_START_L 99 D(I16) INPUT_ACT_PIXEL_START_H 0 D(I17) INPUT_ACT_PIXELS_L 165 D(I18) INPUT_ACT_PIXELS_H 2 D(I19) NOT USED 0 D(I20) NOT USED 0 D(I21) WIN_X_MARGINE 151 D(I22) WIN_Y_MARGINE 146 D(I23) WIN_Y_POSI_L 1 D(I24) WIN_Y_POSI_H 0 D(I25) WIN_Y_SIZE_L 4 D(I26) WIN_Y_SIZE_H 3 D(I27) WIN_X_POSI_L 175 D(I28) WIN_X_POSI_H 0 D(I29) WIN_X_SIZE_L 0 D(I30) WIN_X_SIZE_H 4 D(I31) DS_InX_MARGINE 131 D(I32) DS_OutX_MARGINE 130 D(I33) DS_InY_MARGINE 131 D(I34) DS_OutY_MARGINE 130 D(I35) MARGINE_POS_X 122 D(I36) NOT USED 0 D(I37) NOT USED 0 D(I38) COAST_ENABLE 0 D(I39) NOT USED 0 D(I40) INTERLACE 0 D(I41) DIN_CONTROL_0 3 D(I42) NOT USED 0 D(I43) ahstartL 230 D(I44) ahwidthL 253 D(I45) ahwidth-startH 48 D(I46) VSYNC_CYCLE_L 57 D(I47) VSYNC_CYCLE_H 3 D(I48) NOT USED 0 D(I49) NOT USED 0 D(I50) NOT USED 0 D(I51) NOT USED 0 D(I52) NOT USED 0 DJ:480p(FLL) D(J01) FB_COUNTER1 82 D(J02) FB_COUNTER2 3 D(J03) VCO_DIVIDE 2 D(J04) DELAY 32 D(J05) CHARGE_PUMP 18 D(J06) AMP MODE 1 D(J07) OUTPUT MODE 2 D(J08) OPLL_MDIV_L 46 D(J09) OPLL_MDIV_H 0 D(J10) OPLL_NDIV 18 D(J11) INPUT_ACT_LINE_START_L 44 D(J12) INPUT_ACT_LINE_START_H 0 D(J13) INPUT_ACT_LINES_L 201
Setting
value
Setting No. Setting item
D(J14) INPUT_ACT_LINES_H 1 D(J15) INPUT_ACT_PIXEL_START_L 99 D(J16) INPUT_ACT_PIXEL_START_H 0 D(J17) INPUT_ACT_PIXELS_L 165 D(J18) INPUT_ACT_PIXELS_H 2 D(J19) NOT USED 0 D(J20) NOT USED 0 D(J21) WIN_X_MARGINE 151 D(J22) WIN_Y_MARGINE 146 D(J23) WIN_Y_POSI_L 1 D(J24) WIN_Y_POSI_H 0 D(J25) WIN_Y_SIZE_L 4 D(J26) WIN_Y_SIZE_H 3 D(J27) WIN_X_POSI_L 1 D(J28) WIN_X_POSI_H 0 D(J29) WIN_X_SIZE_L 94 D(J30) WIN_X_SIZE_H 5 D(J31) DS_InX_MARGINE 131 D(J32) DS_OutX_MARGINE 130 D(J33) DS_InY_MARGINE 131 D(J34) DS_OutY_MARGINE 130 D(J35) MARGINE_POS_X 122 D(J36) NOT USED 0 D(J37) NOT USED 0 D(J38) COAST_ENABLE 0 D(J39) NOT USED 0 D(J40) INTERLACE 0 D(J41) DIN_CONTROL_0 3 D(J42) NOT USED 0 D(J43) ahstartL 0 D(J44) ahwidthL 255 D(J45) ahwidth-startH 240 D(J46) VSYNC_CYCLE_L 57 D(J47) VSYNC_CYCLE_H 3 D(J48) NOT USED 0 D(J49) NOT USED 0 D(J50) NOT USED 0 D(J51) NOT USED 0 D(J52) NOT USED 0 DK:480p(ZOOM) D(K01) FB_COUNTER1 82 D(K02) FB_COUNTER2 3 D(K03) VCO_DIVIDE 2 D(K04) DELAY 32 D(K05) CHARGE_PUMP 18 D(K06) AMP MODE 1 D(K07) OUTPUT MODE 2 D(K08) OPLL_MDIV_L 46 D(K09) OPLL_MDIV_H 0 D(K10) OPLL_NDIV 18 D(K11) INPUT_ACT_LINE_START_L 101 D(K12) INPUT_ACT_LINE_START_H 0 D(K13) INPUT_ACT_LINES_L 88 D(K14) INPUT_ACT_LINES_H 1 D(K15) INPUT_ACT_PIXEL_START_L 99
Setting
value
(No.YA067)1-35
Page 36
Setting No. Setting item
D(K16) INPUT_ACT_PIXEL_START_H 0 D(K17) INPUT_ACT_PIXELS_L 165 D(K18) INPUT_ACT_PIXELS_H 2 D(K19) NOT USED 0 D(K20) NOT USED 0 D(K21) WIN_X_MARGINE 151 D(K22) WIN_Y_MARGINE 188 D(K23) WIN_Y_POSI_L 1 D(K24) WIN_Y_POSI_H 0 D(K25) WIN_Y_SIZE_L 4 D(K26) WIN_Y_SIZE_H 3 D(K27) WIN_X_POSI_L 1 D(K28) WIN_X_POSI_H 0 D(K29) WIN_X_SIZE_L 94 D(K30) WIN_X_SIZE_H 5 D(K31) DS_InX_MARGINE 131 D(K32) DS_OutX_MARGINE 130 D(K33) DS_InY_MARGINE 131 D(K34) DS_OutY_MARGINE 130 D(K35) MARGINE_POS_X 122 D(K36) NOT USED 0 D(K37) NOT USED 0 D(K38) COAST_ENABLE 0 D(K39) NOT USED 0 D(K40) INTERLACE 0 D(K41) DIN_CONTROL_0 3 D(K42) NOT USED 0 D(K43) ahstartL 0 D(K44) ahwidthL 255 D(K45) ahwidth-startH 240 D(K46) VSYNC_CYCLE_L 57 D(K47) VSYNC_CYCLE_H 3 D(K48) NOT USED 0 D(K49) NOT USED 0 D(K50) NOT USED 0 D(K51) NOT USED 0 D(K52) NOT USED 0 DL:480p(PANORAMIC) D(L01) FB_COUNTER1 82 D(L02) FB_COUNTER2 3 D(L03) VCO_DIVIDE 2 D(L04) DELAY 32 D(L05) CHARGE_PUMP 18 D(L06) AMP MODE 1 D(L07) OUTPUT MODE 2 D(L08) OPLL_MDIV_L 46 D(L09) OPLL_MDIV_H 0 D(L10) OPLL_NDIV 18 D(L11) INPUT_ACT_LINE_START_L 56 D(L12) INPUT_ACT_LINE_START_H 0 D(L13) INPUT_ACT_LINES_L 177 D(L14) INPUT_ACT_LINES_H 1 D(L15) INPUT_ACT_PIXEL_START_L 99 D(L16) INPUT_ACT_PIXEL_START_H 0 D(L17) INPUT_ACT_PIXELS_L 170
Setting
value
Setting No. Setting item
D(L18) INPUT_ACT_PIXELS_H 2 D(L19) DS_OUTX_PANO_L 104 D(L20) DS_OUTX_PANO_H 2 D(L21) WIN_X_MARGINE 151 D(L22) WIN_Y_MARGINE 156 D(L23) WIN_Y_POSI_L 1 D(L24) WIN_Y_POSI_H 0 D(L25) WIN_Y_SIZE_L 4 D(L26) WIN_Y_SIZE_H 3 D(L27) WIN_X_POSI_L 1 D(L28) WIN_X_POSI_H 0 D(L29) WIN_X_SIZE_L 94 D(L30) WIN_X_SIZE_H 5 D(L31) DS_InX_MARGINE 131 D(L32) DS_OutX_MARGINE 130 D(L33) DS_InY_MARGINE 131 D(L34) DS_OutY_MARGINE 130 D(L35) MARGINE_POS_X 122 D(L36) NOT USED 0 D(L37) NOT USED 0 D(L38) COAST_ENABLE 0 D(L39) NOT USED 0 D(L40) INTERLACE 0 D(L41) DIN_CONTROL_0 3 D(L42) NOT USED 0 D(L43) ahstartL 0 D(L44) ahwidthL 255 D(L45) ahwidth-startH 240 D(L46) VSYNC_CYCLE_L 57 D(L47) VSYNC_CYCLE_H 3 D(L48) NOT USED 0 D(L49) NOT USED 0 D(L50) NOT USED 0 D(L51) NOT USED 0 D(L52) NOT USED 0 DM:576p(REGULAR) D(M01) FB_COUNTER1 88 D(M02) FB_COUNTER2 3 D(M03) VCO_DIVIDE 2 D(M04) DELAY 32 D(M05) CHARGE_PUMP 18 D(M06) AMP MODE 1 D(M07) OUTPUT MODE 2 D(M08) OPLL_MDIV_L 35 D(M09) OPLL_MDIV_H 0 D(M10) OPLL_NDIV 14 D(M11) INPUT_ACT_LINE_START_L 54 D(M12) INPUT_ACT_LINE_START_H 0 D(M13) INPUT_ACT_LINES_L 34 D(M14) INPUT_ACT_LINES_H 2 D(M15) INPUT_ACT_PIXEL_START_L 118 D(M16) INPUT_ACT_PIXEL_START_H 0 D(M17) INPUT_ACT_PIXELS_L 148 D(M18) INPUT_ACT_PIXELS_H 2 D(M19) NOT USED 0
Setting
value
1-36 (No.YA067)
Page 37
Setting No. Setting item
D(M20) NOT USED 0 D(M21) WIN_X_MARGINE 158 D(M22) WIN_Y_MARGINE 148 D(M23) WIN_Y_POSI_L 1 D(M24) WIN_Y_POSI_H 0 D(M25) WIN_Y_SIZE_L 4 D(M26) WIN_Y_SIZE_H 3 D(M27) WIN_X_POSI_L 175 D(M28) WIN_X_POSI_H 0 D(M29) WIN_X_SIZE_L 0 D(M30) WIN_X_SIZE_H 4 D(M31) DS_InX_MARGINE 131 D(M32) DS_OutX_MARGINE 130 D(M33) DS_InY_MARGINE 131 D(M34) DS_OutY_MARGINE 130 D(M35) MARGINE_POS_X 122 D(M36) NOT USED 0 D(M37) NOT USED 0 D(M38) COAST_ENABLE 0 D(M39) NOT USED 0 D(M40) INTERLACE 0 D(M41) DIN_CONTROL_0 3 D(M42) NOT USED 0 D(M43) ahstartL 230 D(M44) ahwidthL 253 D(M45) ahwidth-startH 48 D(M46) VSYNC_CYCLE_L 192 D(M47) VSYNC_CYCLE_H 3 D(M48) NOT USED 0 D(M49) NOT USED 0 D(M50) NOT USED 0 D(M51) NOT USED 0 D(M52) NOT USED 0 DN:576p(FULL) D(N01) FB_COUNTER1 88 D(N02) FB_COUNTER2 3 D(N03) VCO_DIVIDE 2 D(N04) DELAY 32 D(N05) CHARGE_PUMP 18 D(N06) AMP MODE 1 D(N07) OUTPUT MODE 2 D(N08) OPLL_MDIV_L 35 D(N09) OPLL_MDIV_H 0 D(N10) OPLL_NDIV 14 D(N11) INPUT_ACT_LINE_START_L 54 D(N12) INPUT_ACT_LINE_START_H 0 D(N13) INPUT_ACT_LINES_L 34 D(N14) INPUT_ACT_LINES_H 2 D(N15) INPUT_ACT_PIXEL_START_L 117 D(N16) INPUT_ACT_PIXEL_START_H 0 D(N17) INPUT_ACT_PIXELS_L 151 D(N18) INPUT_ACT_PIXELS_H 2 D(N19) NOT USED 0 D(N20) NOT USED 0 D(N21) WIN_X_MARGINE 158
Setting
value
Setting No. Setting item
D(N22) WIN_Y_MARGINE 148 D(N23) WIN_Y_POSI_L 1 D(N24) WIN_Y_POSI_H 0 D(N25) WIN_Y_SIZE_L 4 D(N26) WIN_Y_SIZE_H 3 D(N27) WIN_X_POSI_L 1 D(N28) WIN_X_POSI_H 0 D(N29) WIN_X_SIZE_L 94 D(N30) WIN_X_SIZE_H 5 D(N31) DS_InX_MARGINE 131 D(N32) DS_OutX_MARGINE 130 D(N33) DS_InY_MARGINE 131 D(N34) DS_OutY_MARGINE 130 D(N35) MARGINE_POS_X 122 D(N36) NOT USED 0 D(N37) NOT USED 0 D(N38) COAST_ENABLE 0 D(N39) NOT USED 0 D(N40) INTERLACE 0 D(N41) DIN_CONTROL_0 3 D(N42) NOT USED 0 D(N43) ahstartL 0 D(N44) ahwidthL 255 D(N45) ahwidth-startH 240 D(N46) VSYNC_CYCLE_L 192 D(N47) VSYNC_CYCLE_H 3 D(N48) NOT USED 0 D(N49) NOT USED 0 D(N50) NOT USED 0 D(N51) NOT USED 0 D(N52) NOT USED 0 DO:576p(ZOOM) D(O01) FB_COUNTER1 88 D(O02) FB_COUNTER2 3 D(O03) VCO_DIVIDE 2 D(O04) DELAY 32 D(O05) CHARGE_PUMP 18 D(O06) AMP MODE 1 D(O07) OUTPUT MODE 2 D(O08) OPLL_MDIV_L 35 D(O09) OPLL_MDIV_H 0 D(O10) OPLL_NDIV 14 D(O11) INPUT_ACT_LINE_START_L 122 D(O12) INPUT_ACT_LINE_START_H 0 D(O13) INPUT_ACT_LINES_L 154 D(O14) INPUT_ACT_LINES_H 1 D(O15) INPUT_ACT_PIXEL_START_L 117 D(O16) INPUT_ACT_PIXEL_START_H 0 D(O17) INPUT_ACT_PIXELS_L 151 D(O18) INPUT_ACT_PIXELS_H 2 D(O19) NOT USED 0 D(O20) NOT USED 0 D(O21) WIN_X_MARGINE 158 D(O22) WIN_Y_MARGINE 188 D(O23) WIN_Y_POSI_L 1
Setting
value
(No.YA067)1-37
Page 38
Setting No. Setting item
D(O24) WIN_Y_POSI_H 0 D(O25) WIN_Y_SIZE_L 4 D(O26) WIN_Y_SIZE_H 3 D(O27) WIN_X_POSI_L 1 D(O28) WIN_X_POSI_H 0 D(O29) WIN_X_SIZE_L 94 D(O30) WIN_X_SIZE_H 5 D(O31) DS_InX_MARGINE 131 D(O32) DS_OutX_MARGINE 130 D(O33) DS_InY_MARGINE 131 D(O34) DS_OutY_MARGINE 130 D(O35) MARGINE_POS_X 122 D(O36) NOT USED 0 D(O37) NOT USED 0 D(O38) COAST_ENABLE 0 D(O39) NOT USED 0 D(O40) INTERLACE 0 D(O41) DIN_CONTROL_0 3 D(O42) NOT USED 0 D(O43) ahstartL 0 D(O44) ahwidthL 255 D(O45) ahwidth-startH 240 D(O46) VSYNC_CYCLE_L 192 D(O47) VSYNC_CYCLE_H 3 D(O48) NOT USED 0 D(O49) NOT USED 0 D(O50) NOT USED 0 D(O51) NOT USED 0 D(O52) NOT USED 0 DP:576p(PANORAMIC) D(P01) FB_COUNTER1 88 D(P02) FB_COUNTER2 3 D(P03) VCO_DIVIDE 2 D(P04) DELAY 32 D(P05) CHARGE_PUMP 18 D(P06) AMP MODE 1 D(P07) OUTPUT MODE 2 D(P08) OPLL_MDIV_L 35 D(P09) OPLL_MDIV_H 0 D(P10) OPLL_NDIV 14 D(P11) INPUT_ACT_LINE_START_L 68 D(P12) INPUT_ACT_LINE_START_H 0 D(P13) INPUT_ACT_LINES_L 7 D(P14) INPUT_ACT_LINES_H 2 D(P15) INPUT_ACT_PIXEL_START_L 116 D(P16) INPUT_ACT_PIXEL_START_H 0 D(P17) INPUT_ACT_PIXELS_L 159 D(P18) INPUT_ACT_PIXELS_H 2 D(P19) DS_OUTX_PANO_L 104 D(P20) DS_OUTX_PANO_H 2 D(P21) WIN_X_MARGINE 151 D(P22) WIN_Y_MARGINE 160 D(P23) WIN_Y_POSI_L 1 D(P24) WIN_Y_POSI_H 0 D(P25) WIN_Y_SIZE_L 4
Setting
value
Setting No. Setting item
D(P26) WIN_Y_SIZE_H 3 D(P27) WIN_X_POSI_L 1 D(P28) WIN_X_POSI_H 0 D(P29) WIN_X_SIZE_L 94 D(P30) WIN_X_SIZE_H 5 D(P31) DS_InX_MARGINE 131 D(P32) DS_OutX_MARGINE 130 D(P33) DS_InY_MARGINE 131 D(P34) DS_OutY_MARGINE 130 D(P35) MARGINE_POS_X 122 D(P36) NOT USED 0 D(P37) NOT USED 0 D(P38) COAST_ENABLE 0 D(P39) NOT USED 0 D(P40) INTERLACE 0 D(P41) DIN_CONTROL_0 3 D(P42) NOT USED 0 D(P43) ahstartL 0 D(P44) ahwidthL 255 D(P45) ahwidth-startH 240 D(P46) VSYNC_CYCLE_L 192 D(P47) VSYNC_CYCLE_H 3 D(P48) NOT USED 0 D(P49) NOT USED 0 D(P50) NOT USED 0 D(P51) NOT USED 0 D(P52) NOT USED 0 DQ:COMPO. 720/60p D(Q01) FB_COUNTER1 106 D(Q02) FB_COUNTER2 6 D(Q03) VCO_DIVIDE 1 D(Q04) DELAY 32 D(Q05) CHARGE_PUMP 20 D(Q06) AMP MODE 1 D(Q07) OUTPUT MODE 2 D(Q08) OPLL_MDIV_L 46 D(Q09) OPLL_MDIV_H 0 D(Q10) OPLL_NDIV 18 D(Q11) INPUT_ACT_LINE_START_L 37 D(Q12) INPUT_ACT_LINE_START_H 0 D(Q13) INPUT_ACT_LINES_L 174 D(Q14) INPUT_ACT_LINES_H 2 D(Q15) INPUT_ACT_PIXEL_START_L 15 D(Q16) INPUT_ACT_PIXEL_START_H 1 D(Q17) INPUT_ACT_PIXELS_L 200 D(Q18) INPUT_ACT_PIXELS_H 4 D(Q19) NOT USED 0 D(Q20) NOT USED 0 D(Q21) WIN_X_MARGINE 173 D(Q22) WIN_Y_MARGINE 149 D(Q23) WIN_Y_POSI_L 1 D(Q24) WIN_Y_POSI_H 0 D(Q25) WIN_Y_SIZE_L 4 D(Q26) WIN_Y_SIZE_H 3 D(Q27) WIN_X_POSI_L 1
Setting
value
1-38 (No.YA067)
Page 39
Setting No. Setting item
D(Q28) WIN_X_POSI_H 0 D(Q29) WIN_X_SIZE_L 94 D(Q30) WIN_X_SIZE_H 5 D(Q31) DS_InX_MARGINE 131 D(Q32) DS_OutX_MARGINE 130 D(Q33) DS_InY_MARGINE 131 D(Q34) DS_OutY_MARGINE 130 D(Q35) MARGINE_POS_X 122 D(Q36) NOT USED 0 D(Q37) NOT USED 0 D(Q38) COAST_ENABLE 0 D(Q39) NOT USED 0 D(Q40) INTERLACE 0 D(Q41) DIN_CONTROL_0 3 D(Q42) NOT USED 0 D(Q43) ahstartL 0 D(Q44) ahwidthL 255 D(Q45) ahwidth-startH 240 D(Q46) VSYNC_CYCLE_L 57 D(Q47) VSYNC_CYCLE_H 3 D(Q48) NOT USED 0 D(Q49) NOT USED 0 D(Q50) NOT USED 0 D(Q51) NOT USED 0 D(Q52) NOT USED 0 DR:COMPO 750/50p D(R01) FB_COUNTER1 189 D(R02) FB_COUNTER2 6 D(R03) VCO_DIVIDE 1 D(R04) DELAY 32 D(R05) CHARGE_PUMP 19 D(R06) AMP MODE 1 D(R07) OUTPUT MODE 2 D(R08) OPLL_MDIV_L 35 D(R09) OPLL_MDIV_H 0 D(R10) OPLL_NDIV 14 D(R11) INPUT_ACT_LINE_START_L 30 D(R12) INPUT_ACT_LINE_START_H 0 D(R13) INPUT_ACT_LINES_L 174 D(R14) INPUT_ACT_LINES_H 2 D(R15) INPUT_ACT_PIXEL_START_L 202 D(R16) INPUT_ACT_PIXEL_START_H 0 D(R17) INPUT_ACT_PIXELS_L 48 D(R18) INPUT_ACT_PIXELS_H 4 D(R19) NOT USED 0 D(R20) NOT USED 0 D(R21) WIN_X_MARGINE 173 D(R22) WIN_Y_MARGINE 149 D(R23) WIN_Y_POSI_L 1 D(R24) WIN_Y_POSI_H 0 D(R25) WIN_Y_SIZE_L 4 D(R26) WIN_Y_SIZE_H 3 D(R27) WIN_X_POSI_L 1 D(R28) WIN_X_POSI_H 0 D(R29) WIN_X_SIZE_L 94
Setting
value
Setting No. Setting item
D(R30) WIN_X_SIZE_H 5 D(R31) DS_InX_MARGINE 131 D(R32) DS_OutX_MARGINE 130 D(R33) DS_InY_MARGINE 131 D(R34) DS_OutY_MARGINE 130 D(R35) MARGINE_POS_X 122 D(R36) NOT USED 0 D(R37) NOT USED 0 D(R38) COAST_ENABLE 0 D(R39) NOT USED 0 D(R40) INTERLACE 0 D(R41) DIN_CONTROL_0 3 D(R42) NOT USED 0 D(R43) ahstartL 0 D(R44) ahwidthL 255 D(R45) ahwidth-startH 240 D(R46) VSYNC_CYCLE_L 192 D(R47) VSYNC_CYCLE_H 3 D(R48) NOT USED 0 D(R49) NOT USED 0 D(R50) NOT USED 0 D(R51) NOT USED 0 D(R52) NOT USED 0 DS:COMPO 1080/60i D(S01) FB_COUNTER1 94 D(S02) FB_COUNTER2 7 D(S03) VCO_DIVIDE 1 D(S04) DELAY 32 D(S05) CHARGE_PUMP 19 D(S06) AMP MODE 1 D(S07) OUTPUT MODE 2 D(S08) OPLL_MDIV_L 46 D(S09) OPLL_MDIV_H 0 D(S10) OPLL_NDIV 18 D(S11) INPUT_ACT_LINE_START_L 27 D(S12) INPUT_ACT_LINE_START_H 0 D(S13) INPUT_ACT_LINES_L 4 D(S14) INPUT_ACT_LINES_H 2 D(S15) INPUT_ACT_PIXEL_START_L 186 D(S16) INPUT_ACT_PIXEL_START_H 0 D(S17) INPUT_ACT_PIXELS_L 45 D(S18) INPUT_ACT_PIXELS_H 6 D(S19) NOT USED 0 D(S20) NOT USED 0 D(S21) WIN_X_MARGINE 200 D(S22) WIN_Y_MARGINE 141 D(S23) WIN_Y_POSI_L 1 D(S24) WIN_Y_POSI_H 0 D(S25) WIN_Y_SIZE_L 4 D(S26) WIN_Y_SIZE_H 3 D(S27) WIN_X_POSI_L 1 D(S28) WIN_X_POSI_H 0 D(S29) WIN_X_SIZE_L 94 D(S30) WIN_X_SIZE_H 5 D(S31) DS_InX_MARGINE 131
Setting
value
(No.YA067)1-39
Page 40
Setting No. Setting item
D(S32) DS_OutX_MARGINE 130 D(S33) DS_InY_MARGINE 131 D(S34) DS_OutY_MARGINE 130 D(S35) MARGINE_POS_X 122 D(S36) NOT USED 0 D(S37) NOT USED 0 D(S38) COAST_ENABLE 0 D(S39) NOT USED 0 D(S40) INTERLACE 0 D(S41) DIN_CONTROL_0 3 D(S42) NOT USED 0 D(S43) ahstartL 0 D(S44) ahwidthL 255 D(S45) ahwidth-startH 240 D(S46) VSYNC_CYCLE_L 57 D(S47) VSYNC_CYCLE_H 3 D(S48) NOT USED 0 D(S49) NOT USED 0 D(S50) NOT USED 0 D(S51) NOT USED 0 D(S52) NOT USED 0 DT:COMPO 1080i/50i D(T01) FB_COUNTER1 217 D(T02) FB_COUNTER2 8 D(T03) VCO_DIVIDE 1 D(T04) DELAY 32 D(T05) CHARGE_PUMP 19 D(T06) AMP MODE 1 D(T07) OUTPUT MODE 2 D(T08) OPLL_MDIV_L 35 D(T09) OPLL_MDIV_H 0 D(T10) OPLL_NDIV 14 D(T11) INPUT_ACT_LINE_START_L 22 D(T12) INPUT_ACT_LINE_START_H 0 D(T13) INPUT_ACT_LINES_L 4 D(T14) INPUT_ACT_LINES_H 2 D(T15) INPUT_ACT_PIXEL_START_L 156 D(T16) INPUT_ACT_PIXEL_START_H 0 D(T17) INPUT_ACT_PIXELS_L 45 D(T18) INPUT_ACT_PIXELS_H 6 D(T19) NOT USED 0 D(T20) NOT USED 0 D(T21) WIN_X_MARGINE 200 D(T22) WIN_Y_MARGINE 140 D(T23) WIN_Y_POSI_L 1 D(T24) WIN_Y_POSI_H 0 D(T25) WIN_Y_SIZE_L 4 D(T26) WIN_Y_SIZE_H 3 D(T27) WIN_X_POSI_L 1 D(T28) WIN_X_POSI_H 0 D(T29) WIN_X_SIZE_L 94 D(T30) WIN_X_SIZE_H 5 D(T31) DS_InX_MARGINE 131 D(T32) DS_OutX_MARGINE 130 D(T33) DS_InY_MARGINE 131
Setting
value
Setting No. Setting item
D(T34) DS_OutY_MARGINE 130 D(T35) MARGINE_POS_X 122 D(T36) NOT USED 0 D(T37) NOT USED 0 D(T38) COAST_ENABLE 0 D(T39) NOT USED 0 D(T40) INTERLACE 0 D(T41) DIN_CONTROL_0 3 D(T42) NOT USED 0 D(T43) ahstartL 0 D(T44) ahwidthL 255 D(T45) ahwidth-startH 240 D(T46) VSYNC_CYCLE_L 192 D(T47) VSYNC_CYCLE_H 3 D(T48) NOT USED 0 D(T49) NOT USED 0 D(T50) NOT USED 0 D(T51) NOT USED 0 D(T52) NOT USED 0 DU:COMPO. 1080/50i D(U01) FB_COUNTER1 94 D(U02) FB_COUNTER2 7 D(U03) VCO_DIVIDE 1 D(U04) DELAY 32 D(U05) CHARGE_PUMP 19 D(U06) AMP MODE 1 D(U07) OUTPUT MODE 2 D(U08) OPLL_MDIV_L 46 D(U09) OPLL_MDIV_H 0 D(U10) OPLL_NDIV 18 D(U11) INPUT_ACT_LINE_START_L 46 D(U12) INPUT_ACT_LINE_START_H 0 D(U13) INPUT_ACT_LINES_L 239 D(U14) INPUT_ACT_LINES_H 1 D(U15) INPUT_ACT_PIXEL_START_L 186 D(U16) INPUT_ACT_PIXEL_START_H 0 D(U17) INPUT_ACT_PIXELS_L 45 D(U18) INPUT_ACT_PIXELS_H 6 D(U19) NOT USED 0 D(U20) NOT USED 0 D(U21) WIN_X_MARGINE 200 D(U22) WIN_Y_MARGINE 141 D(U23) WIN_Y_POSI_L 1 D(U24) WIN_Y_POSI_H 0 D(U25) WIN_Y_SIZE_L 4 D(U26) WIN_Y_SIZE_H 3 D(U27) WIN_X_POSI_L 1 D(U28) WIN_X_POSI_H 0 D(U29) WIN_X_SIZE_L 94 D(U30) WIN_X_SIZE_H 5 D(U31) DS_InX_MARGINE 131 D(U32) DS_OutX_MARGINE 130 D(U33) DS_InY_MARGINE 131 D(U34) DS_OutY_MARGINE 130 D(U35) MARGINE_POS_X 122
Setting
value
1-40 (No.YA067)
Page 41
Setting No. Setting item
D(U36) NOT USED 0 D(U37) NOT USED 0 D(U38) COAST_ENABLE 0 D(U39) NOT USED 0 D(U40) INTERLACE 0 D(U41) DIN_CONTROL_0 3 D(U42) NOT USED 0 D(U43) ahstartL 0 D(U44) ahwidthL 255 D(U45) ahwidth-startH 240 D(U46) VSYNC_CYCLE_L 57 D(U47) VSYNC_CYCLE_H 3 D(U48) NOT USED 0 D(U49) NOT USED 0 D(U50) NOT USED 0 D(U51) NOT USED 0 D(U52) NOT USED 0 DV:VGA 400/70(REGULAR) D(V01) FB_COUNTER1 24 D(V02) FB_COUNTER2 3 D(V03) VCO_DIVIDE 2 D(V04) DELAY 28 D(V05) CHARGE_PUMP 18 D(V06) AMP MODE 4 D(V07) OUTPUT MODE 2 D(V08) OPLL_MDIV_L 46 D(V09) OPLL_MDIV_H 0 D(V10) OPLL_NDIV 18 D(V11) INPUT_ACT_LINE_START_L 34 D(V12) INPUT_ACT_LINE_START_H 0 D(V13) INPUT_ACT_LINES_L 144 D(V14) INPUT_ACT_LINES_H 1 D(V15) INPUT_ACT_PIXEL_START_L 93 D(V16) INPUT_ACT_PIXEL_START_H 0 D(V17) INPUT_ACT_PIXELS_L 128 D(V18) INPUT_ACT_PIXELS_H 2 D(V19) NOT USED 0 D(V20) NOT USED 0 D(V21) WIN_X_MARGINE 154 D(V22) WIN_Y_MARGINE 136 D(V23) WIN_Y_POSI_L 64 D(V24) WIN_Y_POSI_H 0 D(V25) WIN_Y_SIZE_L 128 D(V26) WIN_Y_SIZE_H 2 D(V27) WIN_X_POSI_L 175 D(V28) WIN_X_POSI_H 0 D(V29) WIN_X_SIZE_L 0 D(V30) WIN_X_SIZE_H 4 D(V31) DS_InX_MARGINE 131 D(V32) DS_OutX_MARGINE 130 D(V33) DS_InY_MARGINE 131 D(V34) DS_OutY_MARGINE 130 D(V35) MARGINE_POS_X 122 D(V36) NOT USED 0 D(V37) NOT USED 0
Setting
value
Setting No. Setting item
D(V38) COAST_ENABLE 1 D(V39) NOT USED 0 D(V40) INTERLACE 0 D(V41) DIN_CONTROL_0 3 D(V42) NOT USED 0 D(V43) ahstartL 230 D(V44) ahwidthL 253 D(V45) ahwidth-startH 48 D(V46) VSYNC_CYCLE_L 57 D(V47) VSYNC_CYCLE_H 3 D(V48) NOT USED 0 D(V49) NOT USED 0 D(V50) NOT USED 0 D(V51) NOT USED 0 D(V52) NOT USED 0 DW:VGA 400/70(FLL) D(W01) FB_COUNTER1 24 D(W02) FB_COUNTER2 3 D(W03) VCO_DIVIDE 2 D(W04) DELAY 28 D(W05) CHARGE_PUMP 18 D(W06) AMP MODE 4 D(W07) OUTPUT MODE 2 D(W08) OPLL_MDIV_L 46 D(W09) OPLL_MDIV_H 0 D(W10) OPLL_NDIV 18 D(W11) INPUT_ACT_LINE_START_L 33 D(W12) INPUT_ACT_LINE_START_H 0 D(W13) INPUT_ACT_LINES_L 146 D(W14) INPUT_ACT_LINES_H 1 D(W15) INPUT_ACT_PIXEL_START_L 93 D(W16) INPUT_ACT_PIXEL_START_H 0 D(W17) INPUT_ACT_PIXELS_L 128 D(W18) INPUT_ACT_PIXELS_H 2 D(W19) NOT USED 0 D(W20) NOT USED 0 D(W21) WIN_X_MARGINE 154 D(W22) WIN_Y_MARGINE 136 D(W23) WIN_Y_POSI_L 1 D(W24) WIN_Y_POSI_H 0 D(W25) WIN_Y_SIZE_L 4 D(W26) WIN_Y_SIZE_H 3 D(W27) WIN_X_POSI_L 1 D(W28) WIN_X_POSI_H 0 D(W29) WIN_X_SIZE_L 94 D(W30) WIN_X_SIZE_H 5 D(W31) DS_InX_MARGINE 131 D(W32) DS_OutX_MARGINE 130 D(W33) DS_InY_MARGINE 131 D(W34) DS_OutY_MARGINE 130 D(W35) MARGINE_POS_X 122 D(W36) NOT USED 0 D(W37) NOT USED 0 D(W38) COAST_ENABLE 1 D(W39) NOT USED 0
Setting
value
(No.YA067)1-41
Page 42
Setting No. Setting item
D(W40) INTERLACE 0 D(W41) DIN_CONTROL_0 3 D(W42) NOT USED 0 D(W43) ahstartL 0 D(W44) ahwidthL 255 D(W45) ahwidth-startH 240 D(W46) VSYNC_CYCLE_L 57 D(W47) VSYNC_CYCLE_H 3 D(W48) NOT USED 0 D(W49) NOT USED 0 D(W50) NOT USED 0 D(W51) NOT USED 0 D(W52) NOT USED 0 DX:VGA 400/56(PC-98)(REGULAR) D(X01) FB_COUNTER1 72 D(X02) FB_COUNTER2 3 D(X03) VCO_DIVIDE 2 D(X04) DELAY 32 D(X05) CHARGE_PUMP 17 D(X06) AMP MODE 4 D(X07) OUTPUT MODE 2 D(X08) OPLL_MDIV_L 46 D(X09) OPLL_MDIV_H 0 D(X10) OPLL_NDIV 18 D(X11) INPUT_ACT_LINE_START_L 23 D(X12) INPUT_ACT_LINE_START_H 0 D(X13) INPUT_ACT_LINES_L 144 D(X14) INPUT_ACT_LINES_H 1 D(X15) INPUT_ACT_PIXEL_START_L 99 D(X16) INPUT_ACT_PIXEL_START_H 0 D(X17) INPUT_ACT_PIXELS_L 128 D(X18) INPUT_ACT_PIXELS_H 2 D(X19) NOT USED 0 D(X20) NOT USED 0 D(X21) WIN_X_MARGINE 154 D(X22) WIN_Y_MARGINE 136 D(X23) WIN_Y_POSI_L 64 D(X24) WIN_Y_POSI_H 0 D(X25) WIN_Y_SIZE_L 128 D(X26) WIN_Y_SIZE_H 2 D(X27) WIN_X_POSI_L 175 D(X28) WIN_X_POSI_H 0 D(X29) WIN_X_SIZE_L 0 D(X30) WIN_X_SIZE_H 4 D(X31) DS_InX_MARGINE 131 D(X32) DS_OutX_MARGINE 130 D(X33) DS_InY_MARGINE 131 D(X34) DS_OutY_MARGINE 130 D(X35) MARGINE_POS_X 122 D(X36) NOT USED 0 D(X37) NOT USED 0 D(X38) COAST_ENABLE 0 D(X39) NOT USED 0 D(X40) INTERLACE 0 D(X41) DIN_CONTROL_0 3
Setting
value
Setting No. Setting item
D(X42) NOT USED 0 D(X43) ahstartL 230 D(X44) ahwidthL 253 D(X45) ahwidth-startH 48 D(X46) VSYNC_CYCLE_L 57 D(X47) VSYNC_CYCLE_H 3 D(X48) NOT USED 0 D(X49) NOT USED 0 D(X50) NOT USED 0 D(X51) NOT USED 0 D(X52) NOT USED 0 DY:VGA 400/56(PC-98)(FULL) D(Y01) FB_COUNTER1 72 D(Y02) FB_COUNTER2 3 D(Y03) VCO_DIVIDE 2 D(Y04) DELAY 32 D(Y05) CHARGE_PUMP 17 D(Y06) AMP MODE 4 D(Y07) OUTPUT MODE 2 D(Y08) OPLL_MDIV_L 46 D(Y09) OPLL_MDIV_H 0 D(Y10) OPLL_NDIV 18 D(Y11) INPUT_ACT_LINE_START_L 22 D(Y12) INPUT_ACT_LINE_START_H 0 D(Y13) INPUT_ACT_LINES_L 147 D(Y14) INPUT_ACT_LINES_H 1 D(Y15) INPUT_ACT_PIXEL_START_L 98 D(Y16) INPUT_ACT_PIXEL_START_H 0 D(Y17) INPUT_ACT_PIXELS_L 128 D(Y18) INPUT_ACT_PIXELS_H 2 D(Y19) NOT USED 0 D(Y20) NOT USED 0 D(Y21) WIN_X_MARGINE 154 D(Y22) WIN_Y_MARGINE 136 D(Y23) WIN_Y_POSI_L 1 D(Y24) WIN_Y_POSI_H 0 D(Y25) WIN_Y_SIZE_L 4 D(Y26) WIN_Y_SIZE_H 3 D(Y27) WIN_X_POSI_L 1 D(Y28) WIN_X_POSI_H 0 D(Y29) WIN_X_SIZE_L 94 D(Y30) WIN_X_SIZE_H 5 D(Y31) DS_InX_MARGINE 131 D(Y32) DS_OutX_MARGINE 130 D(Y33) DS_InY_MARGINE 131 D(Y34) DS_OutY_MARGINE 130 D(Y35) MARGINE_POS_X 122 D(Y36) NOT USED 0 D(Y37) NOT USED 0 D(Y38) COAST_ENABLE 0 D(Y39) NOT USED 0 D(Y40) INTERLACE 0 D(Y41) DIN_CONTROL_0 3 D(Y42) NOT USED 0 D(Y43) ahstartL 0
Setting
value
1-42 (No.YA067)
Page 43
Setting No. Setting item
D(Y44) ahwidthL 255 D(Y45) ahwidth-startH 240 D(Y46) VSYNC_CYCLE_L 57 D(Y47) VSYNC_CYCLE_H 3 D(Y48) NOT USED 0 D(Y49) NOT USED 0 D(Y50) NOT USED 0 D(Y51) NOT USED 0 D(Y52) NOT USED 0 DZ:VGA/60(REGULAR) D(Z01) FB_COUNTER1 24 D(Z02) FB_COUNTER2 3 D(Z03) VCO_DIVIDE 2 D(Z04) DELAY 32 D(Z05) CHARGE_PUMP 18 D(Z06) AMP MODE 4 D(Z07) OUTPUT MODE 2 D(Z08) OPLL_MDIV_L 46 D(Z09) OPLL_MDIV_H 0 D(Z10) OPLL_NDIV 18 D(Z11) INPUT_ACT_LINE_START_L 30 D(Z12) INPUT_ACT_LINE_START_H 0 D(Z13) INPUT_ACT_LINES_L 228 D(Z14) INPUT_ACT_LINES_H 1 D(Z15) INPUT_ACT_PIXEL_START_L 93 D(Z16) INPUT_ACT_PIXEL_START_H 0 D(Z17) INPUT_ACT_PIXELS_L 128 D(Z18) INPUT_ACT_PIXELS_H 2 D(Z19) NOT USED 0 D(Z20) NOT USED 0 D(Z21) WIN_X_MARGINE 154 D(Z22) WIN_Y_MARGINE 134 D(Z23) WIN_Y_POSI_L 1 D(Z24) WIN_Y_POSI_H 0 D(Z25) WIN_Y_SIZE_L 4 D(Z26) WIN_Y_SIZE_H 3 D(Z27) WIN_X_POSI_L 175 D(Z28) WIN_X_POSI_H 0 D(Z29) WIN_X_SIZE_L 0 D(Z30) WIN_X_SIZE_H 4 D(Z31) DS_InX_MARGINE 131 D(Z32) DS_OutX_MARGINE 130 D(Z33) DS_InY_MARGINE 131 D(Z34) DS_OutY_MARGINE 130 D(Z35) MARGINE_POS_X 122 D(Z36) NOT USED 0 D(Z37) NOT USED 0 D(Z38) COAST_ENABLE 1 D(Z39) NOT USED 0 D(Z40) INTERLACE 0 D(Z41) DIN_CONTROL_0 3 D(Z42) NOT USED 0 D(Z43) ahstartL 230 D(Z44) ahwidthL 253 D(Z45) ahwidth-startH 48
Setting
value
Setting No. Setting item
D(Z46) VSYNC_CYCLE_L 57 D(Z47) VSYNC_CYCLE_H 3 D(Z48) NOT USED 0 D(Z49) NOT USED 0 D(Z50) NOT USED 0 D(Z51) NOT USED 0 D(Z52) NOT USED 0 DAA:VGA/60(FLL) DA(A01) FB_COUNTER1 24 DA(A02) FB_COUNTER2 3 DA(A03) VCO_DIVIDE 2 DA(A04) DELAY 32 DA(A05) CHARGE_PUMP 18 DA(A06) AMP MODE 4 DA(A07) OUTPUT MODE 2 DA(A08) OPLL_MDIV_L 46 DA(A09) OPLL_MDIV_H 0 DA(A10) OPLL_NDIV 18 DA(A11) INPUT_ACT_LINE_START_L 30 DA(A12) INPUT_ACT_LINE_START_H 0 DA(A13) INPUT_ACT_LINES_L 228 DA(A14) INPUT_ACT_LINES_H 1 DA(A15) INPUT_ACT_PIXEL_START_L 93 DA(A16) INPUT_ACT_PIXEL_START_H 0 DA(A17) INPUT_ACT_PIXELS_L 128 DA(A18) INPUT_ACT_PIXELS_H 2 DA(A19) NOT USED 0 DA(A20) NOT USED 0 DA(A21) WIN_X_MARGINE 159 DA(A22) WIN_Y_MARGINE 134 DA(A23) WIN_Y_POSI_L 1 DA(A24) WIN_Y_POSI_H 0 DA(A25) WIN_Y_SIZE_L 4 DA(A26) WIN_Y_SIZE_H 3 DA(A27) WIN_X_POSI_L 1 DA(A28) WIN_X_POSI_H 0 DA(A29) WIN_X_SIZE_L 94 DA(A30) WIN_X_SIZE_H 5 DA(A31) DS_InX_MARGINE 131 DA(A32) DS_OutX_MARGINE 130 DA(A33) DS_InY_MARGINE 131 DA(A34) DS_OutY_MARGINE 130 DA(A35) MARGINE_POS_X 122 DA(A36) NOT USED 0 DA(A37) NOT USED 0 DA(A38) COAST_ENABLE 1 DA(A39) NOT USED 0 DA(A40) INTERLACE 0 DA(A41) DIN_CONTROL_0 3 DA(A42) NOT USED 0 DA(A43) ahstartL 0 DA(A44) ahwidthL 255 DA(A45) ahwidth-startH 240 DA(A46) VSYNC_CYCLE_L 57 DA(A47) VSYNC_CYCLE_H 3
Setting
value
(No.YA067)1-43
Page 44
Setting No. Setting item
DA(A48) NOT USED 0 DA(A49) NOT USED 0 DA(A50) NOT USED 0 DA(A51) NOT USED 0 DA(A52) NOT USED 0 DAB:VGA 72Hz(REGULAR) DA(B01) FB_COUNTER1 56 DA(B02) FB_COUNTER2 3 DA(B03) VCO_DIVIDE 2 DA(B04) DELAY 30 DA(B05) CHARGE_PUMP 19 DA(B06) AMP MODE 4 DA(B07) OUTPUT MODE 2 DA(B08) OPLL_MDIV_L 46 DA(B09) OPLL_MDIV_H 0 DA(B10) OPLL_NDIV 18 DA(B11) INPUT_ACT_LINE_START_L 25 DA(B12) INPUT_ACT_LINE_START_H 0 DA(B13) INPUT_ACT_LINES_L 228 DA(B14) INPUT_ACT_LINES_H 1 DA(B15) INPUT_ACT_PIXEL_START_L 114 DA(B16) INPUT_ACT_PIXEL_START_H 0 DA(B17) INPUT_ACT_PIXELS_L 128 DA(B18) INPUT_ACT_PIXELS_H 2 DA(B19) NOT USED 0 DA(B20) NOT USED 0 DA(B21) WIN_X_MARGINE 152 DA(B22) WIN_Y_MARGINE 134 DA(B23) WIN_Y_POSI_L 1 DA(B24) WIN_Y_POSI_H 0 DA(B25) WIN_Y_SIZE_L 4 DA(B26) WIN_Y_SIZE_H 3 DA(B27) WIN_X_POSI_L 175 DA(B28) WIN_X_POSI_H 0 DA(B29) WIN_X_SIZE_L 0 DA(B30) WIN_X_SIZE_H 4 DA(B31) DS_InX_MARGINE 131 DA(B32) DS_OutX_MARGINE 130 DA(B33) DS_InY_MARGINE 131 DA(B34) DS_OutY_MARGINE 130 DA(B35) MARGINE_POS_X 122 DA(B36) NOT USED 0 DA(B37) NOT USED 0 DA(B38) COAST_ENABLE 1 DA(B39) NOT USED 0 DA(B40) INTERLACE 0 DA(B41) DIN_CONTROL_0 3 DA(B42) NOT USED 0 DA(B43) ahstartL 230 DA(B44) ahwidthL 253 DA(B45) ahwidth-startH 48 DA(B46) VSYNC_CYCLE_L 57 DA(B47) VSYNC_CYCLE_H 3 DA(B48) NOT USED 0 DA(B49) NOT USED 0
Setting
value
Setting No. Setting item
DA(B50) NOT USED 0 DA(B51) NOT USED 0 DA(B52) NOT USED 0 DAC:VGA 72Hz(FULL) DA(C01) FB_COUNTER1 56 DA(C02) FB_COUNTER2 3 DA(C03) VCO_DIVIDE 2 DA(C04) DELAY 30 DA(C05) CHARGE_PUMP 19 DA(C06) AMP MODE 4 DA(C07) OUTPUT MODE 2 DA(C08) OPLL_MDIV_L 46 DA(C09) OPLL_MDIV_H 0 DA(C10) OPLL_NDIV 18 DA(C11) INPUT_ACT_LINE_START_L 25 DA(C12) INPUT_ACT_LINE_START_H 0 DA(C13) INPUT_ACT_LINES_L 228 DA(C14) INPUT_ACT_LINES_H 1 DA(C15) INPUT_ACT_PIXEL_START_L 113 DA(C16) INPUT_ACT_PIXEL_START_H 0 DA(C17) INPUT_ACT_PIXELS_L 128 DA(C18) INPUT_ACT_PIXELS_H 2 DA(C19) NOT USED 0 DA(C20) NOT USED 0 DA(C21) WIN_X_MARGINE 162 DA(C22) WIN_Y_MARGINE 134 DA(C23) WIN_Y_POSI_L 1 DA(C24) WIN_Y_POSI_H 0 DA(C25) WIN_Y_SIZE_L 4 DA(C26) WIN_Y_SIZE_H 3 DA(C27) WIN_X_POSI_L 1 DA(C28) WIN_X_POSI_H 0 DA(C29) WIN_X_SIZE_L 94 DA(C30) WIN_X_SIZE_H 5 DA(C31) DS_InX_MARGINE 131 DA(C32) DS_OutX_MARGINE 130 DA(C33) DS_InY_MARGINE 131 DA(C34) DS_OutY_MARGINE 130 DA(C35) MARGINE_POS_X 122 DA(C36) NOT USED 0 DA(C37) NOT USED 0 DA(C38) COAST_ENABLE 1 DA(C39) NOT USED 0 DA(C40) INTERLACE 0 DA(C41) DIN_CONTROL_0 3 DA(C42) NOT USED 0 DA(C43) ahstartL 0 DA(C44) ahwidthL 255 DA(C45) ahwidth-startH 240 DA(C46) VSYNC_CYCLE_L 57 DA(C47) VSYNC_CYCLE_H 3 DA(C48) NOT USED 0 DA(C49) NOT USED 0 DA(C50) NOT USED 0 DA(C51) NOT USED 0
Setting
value
1-44 (No.YA067)
Page 45
Setting No. Setting item
DA(C52) NOT USED 0 DAD:VGA 75Hz(REGULAR) DA(D01) FB_COUNTER1 64 DA(D02) FB_COUNTER2 3 DA(D03) VCO_DIVIDE 2 DA(D04) DELAY 28 DA(D05) CHARGE_PUMP 19 DA(D06) AMP MODE 4 DA(D07) OUTPUT MODE 2 DA(D08) OPLL_MDIV_L 46 DA(D09) OPLL_MDIV_H 0 DA(D10) OPLL_NDIV 18 DA(D11) INPUT_ACT_LINE_START_L 13 DA(D12) INPUT_ACT_LINE_START_H 0 DA(D13) INPUT_ACT_LINES_L 228 DA(D14) INPUT_ACT_LINES_H 1 DA(D15) INPUT_ACT_PIXEL_START_L 130 DA(D16) INPUT_ACT_PIXEL_START_H 0 DA(D17) INPUT_ACT_PIXELS_L 128 DA(D18) INPUT_ACT_PIXELS_H 2 DA(D19) NOT USED 0 DA(D20) NOT USED 0 DA(D21) WIN_X_MARGINE 152 DA(D22) WIN_Y_MARGINE 128 DA(D23) WIN_Y_POSI_L 1 DA(D24) WIN_Y_POSI_H 0 DA(D25) WIN_Y_SIZE_L 4 DA(D26) WIN_Y_SIZE_H 3 DA(D27) WIN_X_POSI_L 175 DA(D28) WIN_X_POSI_H 0 DA(D29) WIN_X_SIZE_L 0 DA(D30) WIN_X_SIZE_H 4 DA(D31) DS_InX_MARGINE 131 DA(D32) DS_OutX_MARGINE 130 DA(D33) DS_InY_MARGINE 131 DA(D34) DS_OutY_MARGINE 130 DA(D35) MARGINE_POS_X 122 DA(D36) NOT USED 0 DA(D37) NOT USED 0 DA(D38) COAST_ENABLE 1 DA(D39) NOT USED 0 DA(D40) INTERLACE 0 DA(D41) DIN_CONTROL_0 3 DA(D42) NOT USED 0 DA(D43) ahstartL 230 DA(D44) ahwidthL 253 DA(D45) ahwidth-startH 48 DA(D46) VSYNC_CYCLE_L 57 DA(D47) VSYNC_CYCLE_H 3 DA(D48) NOT USED 0 DA(D49) NOT USED 0 DA(D50) NOT USED 0 DA(D51) NOT USED 0 DA(D52) NOT USED 0 DAE:VGA 75Hz(FULL)
Setting
value
Setting No. Setting item
DA(E01) FB_COUNTER1 64 DA(E02) FB_COUNTER2 3 DA(E03) VCO_DIVIDE 2 DA(E04) DELAY 28 DA(E05) CHARGE_PUMP 19 DA(E06) AMP MODE 4 DA(E07) OUTPUT MODE 2 DA(E08) OPLL_MDIV_L 46 DA(E09) OPLL_MDIV_H 0 DA(E10) OPLL_NDIV 18 DA(E11) INPUT_ACT_LINE_START_L 13 DA(E12) INPUT_ACT_LINE_START_H 0 DA(E13) INPUT_ACT_LINES_L 228 DA(E14) INPUT_ACT_LINES_H 1 DA(E15) INPUT_ACT_PIXEL_START_L 130 DA(E16) INPUT_ACT_PIXEL_START_H 0 DA(E17) INPUT_ACT_PIXELS_L 128 DA(E18) INPUT_ACT_PIXELS_H 2 DA(E19) NOT USED 0 DA(E20) NOT USED 0 DA(E21) WIN_X_MARGINE 156 DA(E22) WIN_Y_MARGINE 128 DA(E23) WIN_Y_POSI_L 1 DA(E24) WIN_Y_POSI_H 0 DA(E25) WIN_Y_SIZE_L 4 DA(E26) WIN_Y_SIZE_H 3 DA(E27) WIN_X_POSI_L 1 DA(E28) WIN_X_POSI_H 0 DA(E29) WIN_X_SIZE_L 94 DA(E30) WIN_X_SIZE_H 5 DA(E31) DS_InX_MARGINE 131 DA(E32) DS_OutX_MARGINE 130 DA(E33) DS_InY_MARGINE 131 DA(E34) DS_OutY_MARGINE 130 DA(E35) MARGINE_POS_X 122 DA(E36) NOT USED 0 DA(E37) NOT USED 0 DA(E38) COAST_ENABLE 1 DA(E39) NOT USED 0 DA(E40) INTERLACE 0 DA(E41) DIN_CONTROL_0 3 DA(E42) NOT USED 0 DA(E43) ahstartL 0 DA(E44) ahwidthL 255 DA(E45) ahwidth-startH 240 DA(E46) VSYNC_CYCLE_L 57 DA(E47) VSYNC_CYCLE_H 3 DA(E48) NOT USED 0 DA(E49) NOT USED 0 DA(E50) NOT USED 0 DA(E51) NOT USED 0 DA(E52) NOT USED 0 DAF:MAC13(REGULAR) DA(F01) FB_COUNTER1 88 DA(F02) FB_COUNTER2 3
Setting
value
(No.YA067)1-45
Page 46
Setting No. Setting item
DA(F03) VCO_DIVIDE 2 DA(F04) DELAY 46 DA(F05) CHARGE_PUMP 19 DA(F06) AMP MODE 4 DA(F07) OUTPUT MODE 2 DA(F08) OPLL_MDIV_L 46 DA(F09) OPLL_MDIV_H 0 DA(F10) OPLL_NDIV 18 DA(F11) INPUT_ACT_LINE_START_L 36 DA(F12) INPUT_ACT_LINE_START_H 0 DA(F13) INPUT_ACT_LINES_L 228 DA(F14) INPUT_ACT_LINES_H 1 DA(F15) INPUT_ACT_PIXEL_START_L 107 DA(F16) INPUT_ACT_PIXEL_START_H 0 DA(F17) INPUT_ACT_PIXELS_L 128 DA(F18) INPUT_ACT_PIXELS_H 2 DA(F19) NOT USED 0 DA(F20) NOT USED 0 DA(F21) WIN_X_MARGINE 150 DA(F22) WIN_Y_MARGINE 129 DA(F23) WIN_Y_POSI_L 1 DA(F24) WIN_Y_POSI_H 0 DA(F25) WIN_Y_SIZE_L 4 DA(F26) WIN_Y_SIZE_H 3 DA(F27) WIN_X_POSI_L 175 DA(F28) WIN_X_POSI_H 0 DA(F29) WIN_X_SIZE_L 0 DA(F30) WIN_X_SIZE_H 4 DA(F31) DS_InX_MARGINE 131 DA(F32) DS_OutX_MARGINE 130 DA(F33) DS_InY_MARGINE 131 DA(F34) DS_OutY_MARGINE 130 DA(F35) MARGINE_POS_X 122 DA(F36) NOT USED 0 DA(F37) NOT USED 0 DA(F38) COAST_ENABLE 1 DA(F39) NOT USED 0 DA(F40) INTERLACE 0 DA(F41) DIN_CONTROL_0 3 DA(F42) NOT USED 0 DA(F43) ahstartL 230 DA(F44) ahwidthL 253 DA(F45) ahwidth-startH 48 DA(F46) VSYNC_CYCLE_L 57 DA(F47) VSYNC_CYCLE_H 3 DA(F48) NOT USED 0 DA(F49) NOT USED 0 DA(F50) NOT USED 0 DA(F51) NOT USED 0 DA(F52) NOT USED 0 DAG:MAC13(FULL) DA(G01) FB_COUNTER1 88 DA(G02) FB_COUNTER2 3 DA(G03) VCO_DIVIDE 2 DA(G04) DELAY 46
Setting
value
Setting No. Setting item
DA(G05) CHARGE_PUMP 19 DA(G06) AMP MODE 4 DA(G07) OUTPUT MODE 2 DA(G08) OPLL_MDIV_L 46 DA(G09) OPLL_MDIV_H 0 DA(G10) OPLL_NDIV 18 DA(G11) INPUT_ACT_LINE_START_L 36 DA(G12) INPUT_ACT_LINE_START_H 0 DA(G13) INPUT_ACT_LINES_L 228 DA(G14) INPUT_ACT_LINES_H 1 DA(G15) INPUT_ACT_PIXEL_START_L 107 DA(G16) INPUT_ACT_PIXEL_START_H 0 DA(G17) INPUT_ACT_PIXELS_L 128 DA(G18) INPUT_ACT_PIXELS_H 2 DA(G19) NOT USED 0 DA(G20) NOT USED 0 DA(G21) WIN_X_MARGINE 155 DA(G22) WIN_Y_MARGINE 129 DA(G23) WIN_Y_POSI_L 1 DA(G24) WIN_Y_POSI_H 0 DA(G25) WIN_Y_SIZE_L 4 DA(G26) WIN_Y_SIZE_H 3 DA(G27) WIN_X_POSI_L 1 DA(G28) WIN_X_POSI_H 0 DA(G29) WIN_X_SIZE_L 94 DA(G30) WIN_X_SIZE_H 5 DA(G31) DS_InX_MARGINE 131 DA(G32) DS_OutX_MARGINE 130 DA(G33) DS_InY_MARGINE 131 DA(G34) DS_OutY_MARGINE 130 DA(G35) MARGINE_POS_X 122 DA(G36) NOT USED 0 DA(G37) NOT USED 0 DA(G38) COAST_ENABLE 1 DA(G39) NOT USED 0 DA(G40) INTERLACE 0 DA(G41) DIN_CONTROL_0 3 DA(G42) NOT USED 0 DA(G43) ahstartL 0 DA(G44) ahwidthL 255 DA(G45) ahwidth-startH 240 DA(G46) VSYNC_CYCLE_L 57 DA(G47) VSYNC_CYCLE_H 3 DA(G48) NOT USED 0 DA(G49) NOT USED 0 DA(G50) NOT USED 0 DA(G51) NOT USED 0 DA(G52) NOT USED 0 DAH: SVGA 72Hz(REGULAR) DA(H01) FB_COUNTER1 8 DA(H02) FB_COUNTER2 4 DA(H03) VCO_DIVIDE 1 DA(H04) DELAY 48 DA(H05) CHARGE_PUMP 18 DA(H06) AMP MODE 4
Setting
value
1-46 (No.YA067)
Page 47
Setting No. Setting item
DA(H07) OUTPUT MODE 2 DA(H08) OPLL_MDIV_L 46 DA(H09) OPLL_MDIV_H 0 DA(H10) OPLL_NDIV 18 DA(H11) INPUT_ACT_LINE_START_L 20 DA(H12) INPUT_ACT_LINE_START_H 0 DA(H13) INPUT_ACT_LINES_L 92 DA(H14) INPUT_ACT_LINES_H 2 DA(H15) INPUT_ACT_PIXEL_START_L 122 DA(H16) INPUT_ACT_PIXEL_START_H 0 DA(H17) INPUT_ACT_PIXELS_L 28 DA(H18) INPUT_ACT_PIXELS_H 3 DA(H19) NOT USED 0 DA(H20) NOT USED 0 DA(H21) WIN_X_MARGINE 178 DA(H22) WIN_Y_MARGINE 162 DA(H23) WIN_Y_POSI_L 1 DA(H24) WIN_Y_POSI_H 0 DA(H25) WIN_Y_SIZE_L 4 DA(H26) WIN_Y_SIZE_H 3 DA(H27) WIN_X_POSI_L 175 DA(H28) WIN_X_POSI_H 0 DA(H29) WIN_X_SIZE_L 0 DA(H30) WIN_X_SIZE_H 4 DA(H31) DS_InX_MARGINE 131 DA(H32) DS_OutX_MARGINE 130 DA(H33) DS_InY_MARGINE 131 DA(H34) DS_OutY_MARGINE 130 DA(H35) MARGINE_POS_X 122 DA(H36) NOT USED 0 DA(H37) NOT USED 0 DA(H38) COAST_ENABLE 1 DA(H39) NOT USED 0 DA(H40) INTERLACE 0 DA(H41) DIN_CONTROL_0 3 DA(H42) NOT USED 0 DA(H43) ahstartL 230 DA(H44) ahwidthL 253 DA(H45) ahwidth-startH 48 DA(H46) VSYNC_CYCLE_L 57 DA(H47) VSYNC_CYCLE_H 3 DA(H48) NOT USED 0 DA(H49) NOT USED 0 DA(H50) NOT USED 0 DA(H51) NOT USED 0 DA(H52) NOT USED 0 DAI:SVGA 72Hz(FULL) DA(I01) FB_COUNTER1 8 DA(I02) FB_COUNTER2 4 DA(I03) VCO_DIVIDE 1 DA(I04) DELAY 46 DA(I05) CHARGE_PUMP 18 DA(I06) AMP MODE 4 DA(I07) OUTPUT MODE 2 DA(I08) OPLL_MDIV_L 46
Setting
value
Setting No. Setting item
DA(I09) OPLL_MDIV_H 0 DA(I10) OPLL_NDIV 18 DA(I11) INPUT_ACT_LINE_START_L 20 DA(I12) INPUT_ACT_LINE_START_H 0 DA(I13) INPUT_ACT_LINES_L 92 DA(I14) INPUT_ACT_LINES_H 2 DA(I15) INPUT_ACT_PIXEL_START_L 120 DA(I16) INPUT_ACT_PIXEL_START_H 0 DA(I17) INPUT_ACT_PIXELS_L 31 DA(I18) INPUT_ACT_PIXELS_H 3 DA(I19) NOT USED 0 DA(I20) NOT USED 0 DA(I21) WIN_X_MARGINE 178 DA(I22) WIN_Y_MARGINE 164 DA(I23) WIN_Y_POSI_L 1 DA(I24) WIN_Y_POSI_H 0 DA(I25) WIN_Y_SIZE_L 4 DA(I26) WIN_Y_SIZE_H 3 DA(I27) WIN_X_POSI_L 1 DA(I28) WIN_X_POSI_H 0 DA(I29) WIN_X_SIZE_L 94 DA(I30) WIN_X_SIZE_H 5 DA(I31) DS_InX_MARGINE 131 DA(I32) DS_OutX_MARGINE 130 DA(I33) DS_InY_MARGINE 131 DA(I34) DS_OutY_MARGINE 130 DA(I35) MARGINE_POS_X 122 DA(I36) NOT USED 0 DA(I37) NOT USED 0 DA(I38) COAST_ENABLE 1 DA(I39) NOT USED 0 DA(I40) INTERLACE 0 DA(I41) DIN_CONTROL_0 3 DA(I42) NOT USED 0 DA(I43) ahstartL 0 DA(I44) ahwidthL 255 DA(I45) ahwidth-startH 240 DA(I46) VSYNC_CYCLE_L 57 DA(I47) VSYNC_CYCLE_H 3 DA(I48) NOT USED 0 DA(I49) NOT USED 0 DA(I50) NOT USED 0 DA(I51) NOT USED 0 DA(I52) NOT USED 0 DAJ:SVGA 56.2Hz(REGULAR) DA(J01) FB_COUNTER1 248 DA(J02) FB_COUNTER2 3 DA(J03) VCO_DIVIDE 2 DA(J04) DELAY 22 DA(J05) CHARGE_PUMP 20 DA(J06) AMP MODE 4 DA(J07) OUTPUT MODE 2 DA(J08) OPLL_MDIV_L 46 DA(J09) OPLL_MDIV_H 0 DA(J10) OPLL_NDIV 18
Setting
value
(No.YA067)1-47
Page 48
Setting No. Setting item
DA(J11) INPUT_ACT_LINE_START_L 19 DA(J12) INPUT_ACT_LINE_START_H 0 DA(J13) INPUT_ACT_LINES_L 92 DA(J14) INPUT_ACT_LINES_H 2 DA(J15) INPUT_ACT_PIXEL_START_L 146 DA(J16) INPUT_ACT_PIXEL_START_H 0 DA(J17) INPUT_ACT_PIXELS_L 28 DA(J18) INPUT_ACT_PIXELS_H 3 DA(J19) NOT USED 0 DA(J20) NOT USED 0 DA(J21) WIN_X_MARGINE 156 DA(J22) WIN_Y_MARGINE 127 DA(J23) WIN_Y_POSI_L 1 DA(J24) WIN_Y_POSI_H 0 DA(J25) WIN_Y_SIZE_L 4 DA(J26) WIN_Y_SIZE_H 3 DA(J27) WIN_X_POSI_L 175 DA(J28) WIN_X_POSI_H 0 DA(J29) WIN_X_SIZE_L 0 DA(J30) WIN_X_SIZE_H 4 DA(J31) DS_InX_MARGINE 131 DA(J32) DS_OutX_MARGINE 130 DA(J33) DS_InY_MARGINE 131 DA(J34) DS_OutY_MARGINE 130 DA(J35) MARGINE_POS_X 122 DA(J36) NOT USED 0 DA(J37) NOT USED 0 DA(J38) COAST_ENABLE 1 DA(J39) NOT USED 0 DA(J40) INTERLACE 0 DA(J41) DIN_CONTROL_0 3 DA(J42) NOT USED 0 DA(J43) ahstartL 230 DA(J44) ahwidthL 253 DA(J45) ahwidth-startH 48 DA(J46) VSYNC_CYCLE_L 57 DA(J47) VSYNC_CYCLE_H 3 DA(J48) NOT USED 0 DA(J49) NOT USED 0 DA(J50) NOT USED 0 DA(J51) NOT USED 0 DA(J52) NOT USED 0 DAK:SVGA 56.2Hz(FULL) DA(K01) FB_COUNTER1 248 DA(K02) FB_COUNTER2 3 DA(K03) VCO_DIVIDE 2 DA(K04) DELAY 22 DA(K05) CHARGE_PUMP 20 DA(K06) AMP MODE 4 DA(K07) OUTPUT MODE 2 DA(K08) OPLL_MDIV_L 46 DA(K09) OPLL_MDIV_H 0 DA(K10) OPLL_NDIV 18 DA(K11) INPUT_ACT_LINE_START_L 19 DA(K12) INPUT_ACT_LINE_START_H 0
Setting
value
Setting No. Setting item
DA(K13) INPUT_ACT_LINES_L 92 DA(K14) INPUT_ACT_LINES_H 2 DA(K15) INPUT_ACT_PIXEL_START_L 144 DA(K16) INPUT_ACT_PIXEL_START_H 0 DA(K17) INPUT_ACT_PIXELS_L 31 DA(K18) INPUT_ACT_PIXELS_H 3 DA(K19) NOT USED 0 DA(K20) NOT USED 0 DA(K21) WIN_X_MARGINE 156 DA(K22) WIN_Y_MARGINE 127 DA(K23) WIN_Y_POSI_L 1 DA(K24) WIN_Y_POSI_H 0 DA(K25) WIN_Y_SIZE_L 4 DA(K26) WIN_Y_SIZE_H 3 DA(K27) WIN_X_POSI_L 1 DA(K28) WIN_X_POSI_H 0 DA(K29) WIN_X_SIZE_L 94 DA(K30) WIN_X_SIZE_H 5 DA(K31) DS_InX_MARGINE 131 DA(K32) DS_OutX_MARGINE 130 DA(K33) DS_InY_MARGINE 131 DA(K34) DS_OutY_MARGINE 130 DA(K35) MARGINE_POS_X 122 DA(K36) NOT USED 0 DA(K37) NOT USED 0 DA(K38) COAST_ENABLE 1 DA(K39) NOT USED 0 DA(K40) INTERLACE 0 DA(K41) DIN_CONTROL_0 3 DA(K42) NOT USED 0 DA(K43) ahstartL 0 DA(K44) ahwidthL 255 DA(K45) ahwidth-startH 240 DA(K46) VSYNC_CYCLE_L 57 DA(K47) VSYNC_CYCLE_H 3 DA(K48) NOT USED 0 DA(K49) NOT USED 0 DA(K50) NOT USED 0 DA(K51) NOT USED 0 DA(K52) NOT USED 0 DAL:SVGA 60.3Hz(RGULAR) DA(L01) FB_COUNTER1 24 DA(L02) FB_COUNTER2 4 DA(L03) VCO_DIVIDE 1 DA(L04) DELAY 46 DA(L05) CHARGE_PUMP 17 DA(L06) AMP MODE 4 DA(L07) OUTPUT MODE 2 DA(L08) OPLL_MDIV_L 46 DA(L09) OPLL_MDIV_H 0 DA(L10) OPLL_NDIV 18 DA(L11) INPUT_ACT_LINE_START_L 20 DA(L12) INPUT_ACT_LINE_START_H 0 DA(L13) INPUT_ACT_LINES_L 92 DA(L14) INPUT_ACT_LINES_H 2
Setting
value
1-48 (No.YA067)
Page 49
Setting No. Setting item
DA(L15) INPUT_ACT_PIXEL_START_L 159 DA(L16) INPUT_ACT_PIXEL_START_H 0 DA(L17) INPUT_ACT_PIXELS_L 28 DA(L18) INPUT_ACT_PIXELS_H 3 DA(L19) NOT USED 0 DA(L20) NOT USED 0 DA(L21) WIN_X_MARGINE 158 DA(L22) WIN_Y_MARGINE 128 DA(L23) WIN_Y_POSI_L 1 DA(L24) WIN_Y_POSI_H 0 DA(L25) WIN_Y_SIZE_L 4 DA(L26) WIN_Y_SIZE_H 3 DA(L27) WIN_X_POSI_L 175 DA(L28) WIN_X_POSI_H 0 DA(L29) WIN_X_SIZE_L 0 DA(L30) WIN_X_SIZE_H 4 DA(L31) DS_InX_MARGINE 131 DA(L32) DS_OutX_MARGINE 130 DA(L33) DS_InY_MARGINE 131 DA(L34) DS_OutY_MARGINE 130 DA(L35) MARGINE_POS_X 122 DA(L36) NOT USED 0 DA(L37) NOT USED 0 DA(L38) COAST_ENABLE 1 DA(L39) NOT USED 0 DA(L40) INTERLACE 0 DA(L41) DIN_CONTROL_0 3 DA(L42) NOT USED 0 DA(L43) ahstartL 230 DA(L44) ahwidthL 253 DA(L45) ahwidth-startH 48 DA(L46) VSYNC_CYCLE_L 57 DA(L47) VSYNC_CYCLE_H 3 DA(L48) NOT USED 0 DA(L49) NOT USED 0 DA(L50) NOT USED 0 DA(L51) NOT USED 0 DA(L52) NOT USED 0 DAM:SVGA 60.3Hz(REGULAR) DA(M01) FB_COUNTER1 24 DA(M02) FB_COUNTER2 4 DA(M03) VCO_DIVIDE 1 DA(M04) DELAY 48 DA(M05) CHARGE_PUMP 17 DA(M06) AMP MODE 4 DA(M07) OUTPUT MODE 2 DA(M08) OPLL_MDIV_L 46 DA(M09) OPLL_MDIV_H 0 DA(M10) OPLL_NDIV 18 DA(M11) INPUT_ACT_LINE_START_L 20 DA(M12) INPUT_ACT_LINE_START_H 0 DA(M13) INPUT_ACT_LINES_L 93 DA(M14) INPUT_ACT_LINES_H 2 DA(M15) INPUT_ACT_PIXEL_START_L 157 DA(M16) INPUT_ACT_PIXEL_START_H 0
Setting
value
Setting No. Setting item
DA(M17) INPUT_ACT_PIXELS_L 31 DA(M18) INPUT_ACT_PIXELS_H 3 DA(M19) NOT USED 0 DA(M20) NOT USED 0 DA(M21) WIN_X_MARGINE 158 DA(M22) WIN_Y_MARGINE 128 DA(M23) WIN_Y_POSI_L 1 DA(M24) WIN_Y_POSI_H 0 DA(M25) WIN_Y_SIZE_L 4 DA(M26) WIN_Y_SIZE_H 3 DA(M27) WIN_X_POSI_L 1 DA(M28) WIN_X_POSI_H 0 DA(M29) WIN_X_SIZE_L 94 DA(M30) WIN_X_SIZE_H 5 DA(M31) DS_InX_MARGINE 131 DA(M32) DS_OutX_MARGINE 130 DA(M33) DS_InY_MARGINE 131 DA(M34) DS_OutY_MARGINE 130 DA(M35) MARGINE_POS_X 122 DA(M36) NOT USED 0 DA(M37) NOT USED 0 DA(M38) COAST_ENABLE 1 DA(M39) NOT USED 0 DA(M40) INTERLACE 0 DA(M41) DIN_CONTROL_0 3 DA(M42) NOT USED 0 DA(M43) ahstartL 0 DA(M44) ahwidthL 255 DA(M45) ahwidth-startH 240 DA(M46) VSYNC_CYCLE_L 57 DA(M47) VSYNC_CYCLE_H 3 DA(M48) NOT USED 0 DA(M49) NOT USED 0 DA(M50) NOT USED 0 DA(M51) NOT USED 0 DA(M52) NOT USED 0 DAN:SVGA 75Hz(REGULAR) DA(N01) FB_COUNTER1 24 DA(N02) FB_COUNTER2 4 DA(N03) VCO_DIVIDE 1 DA(N04) DELAY 28 DA(N05) CHARGE_PUMP 18 DA(N06) AMP MODE 4 DA(N07) OUTPUT MODE 2 DA(N08) OPLL_MDIV_L 46 DA(N09) OPLL_MDIV_H 0 DA(N10) OPLL_NDIV 18 DA(N11) INPUT_ACT_LINE_START_L 18 DA(N12) INPUT_ACT_LINE_START_H 0 DA(N13) INPUT_ACT_LINES_L 93 DA(N14) INPUT_ACT_LINES_H 2 DA(N15) INPUT_ACT_PIXEL_START_L 179 DA(N16) INPUT_ACT_PIXEL_START_H 0 DA(N17) INPUT_ACT_PIXELS_L 28 DA(N18) INPUT_ACT_PIXELS_H 3
Setting
value
(No.YA067)1-49
Page 50
Setting No. Setting item
DA(N19) NOT USED 0 DA(N20) NOT USED 0 DA(N21) WIN_X_MARGINE 158 DA(N22) WIN_Y_MARGINE 127 DA(N23) WIN_Y_POSI_L 1 DA(N24) WIN_Y_POSI_H 0 DA(N25) WIN_Y_SIZE_L 4 DA(N26) WIN_Y_SIZE_H 3 DA(N27) WIN_X_POSI_L 175 DA(N28) WIN_X_POSI_H 0 DA(N29) WIN_X_SIZE_L 0 DA(N30) WIN_X_SIZE_H 4 DA(N31) DS_InX_MARGINE 131 DA(N32) DS_OutX_MARGINE 130 DA(N33) DS_InY_MARGINE 131 DA(N34) DS_OutY_MARGINE 130 DA(N35) MARGINE_POS_X 122 DA(N36) NOT USED 0 DA(N37) NOT USED 0 DA(N38) COAST_ENABLE 1 DA(N39) NOT USED 0 DA(N40) INTERLACE 0 DA(N41) DIN_CONTROL_0 3 DA(N42) NOT USED 0 DA(N43) ahstartL 230 DA(N44) ahwidthL 253 DA(N45) ahwidth-startH 48 DA(N46) VSYNC_CYCLE_L 57 DA(N47) VSYNC_CYCLE_H 3 DA(N48) NOT USED 0 DA(N49) NOT USED 0 DA(N50) NOT USED 0 DA(N51) NOT USED 0 DA(N52) NOT USED 0 DAO:SVGA 75Hz(FULL) DA(O01) FB_COUNTER1 24 DA(O02) FB_COUNTER2 4 DA(O03) VCO_DIVIDE 1 DA(O04) DELAY 28 DA(O05) CHARGE_PUMP 18 DA(O06) AMP MODE 4 DA(O07) OUTPUT MODE 2 DA(O08) OPLL_MDIV_L 46 DA(O09) OPLL_MDIV_H 0 DA(O10) OPLL_NDIV 18 DA(O11) INPUT_ACT_LINE_START_L 18 DA(O12) INPUT_ACT_LINE_START_H 0 DA(O13) INPUT_ACT_LINES_L 93 DA(O14) INPUT_ACT_LINES_H 2 DA(O15) INPUT_ACT_PIXEL_START_L 177 DA(O16) INPUT_ACT_PIXEL_START_H 0 DA(O17) INPUT_ACT_PIXELS_L 32 DA(O18) INPUT_ACT_PIXELS_H 3 DA(O19) NOT USED 0 DA(O20) NOT USED 0
Setting
value
Setting No. Setting item
DA(O21) WIN_X_MARGINE 158 DA(O22) WIN_Y_MARGINE 127 DA(O23) WIN_Y_POSI_L 1 DA(O24) WIN_Y_POSI_H 0 DA(O25) WIN_Y_SIZE_L 4 DA(O26) WIN_Y_SIZE_H 3 DA(O27) WIN_X_POSI_L 1 DA(O28) WIN_X_POSI_H 0 DA(O29) WIN_X_SIZE_L 94 DA(O30) WIN_X_SIZE_H 5 DA(O31) DS_InX_MARGINE 131 DA(O32) DS_OutX_MARGINE 130 DA(O33) DS_InY_MARGINE 131 DA(O34) DS_OutY_MARGINE 130 DA(O35) MARGINE_POS_X 122 DA(O36) NOT USED 0 DA(O37) NOT USED 0 DA(O38) COAST_ENABLE 1 DA(O39) NOT USED 0 DA(O40) INTERLACE 0 DA(O41) DIN_CONTROL_0 3 DA(O42) NOT USED 0 DA(O43) ahstartL 0 DA(O44) ahwidthL 255 DA(O45) ahwidth-startH 240 DA(O46) VSYNC_CYCLE_L 57 DA(O47) VSYNC_CYCLE_H 3 DA(O48) NOT USED 0 DA(O49) NOT USED 0 DA(O50) NOT USED 0 DA(O51) NOT USED 0 DA(O52) NOT USED 0 DAP:XGA 60Hz(REGULAR) DA(P01) FB_COUNTER1 56 DA(P02) FB_COUNTER2 5 DA(P03) VCO_DIVIDE 1 DA(P04) DELAY 38 DA(P05) CHARGE_PUMP 19 DA(P06) AMP MODE 4 DA(P07) OUTPUT MODE 2 DA(P08) OPLL_MDIV_L 46 DA(P09) OPLL_MDIV_H 0 DA(P10) OPLL_NDIV 18 DA(P11) INPUT_ACT_LINE_START_L 26 DA(P12) INPUT_ACT_LINE_START_H 0 DA(P13) INPUT_ACT_LINES_L 4 DA(P14) INPUT_ACT_LINES_H 3 DA(P15) INPUT_ACT_PIXEL_START_L 225 DA(P16) INPUT_ACT_PIXEL_START_H 0 DA(P17) INPUT_ACT_PIXELS_L 0 DA(P18) INPUT_ACT_PIXELS_H 4 DA(P19) NOT USED 0 DA(P20) NOT USED 0 DA(P21) WIN_X_MARGINE 162 DA(P22) WIN_Y_MARGINE 132
Setting
value
1-50 (No.YA067)
Page 51
Setting No. Setting item
DA(P23) WIN_Y_POSI_L 1 DA(P24) WIN_Y_POSI_H 0 DA(P25) WIN_Y_SIZE_L 4 DA(P26) WIN_Y_SIZE_H 3 DA(P27) WIN_X_POSI_L 175 DA(P28) WIN_X_POSI_H 0 DA(P29) WIN_X_SIZE_L 0 DA(P30) WIN_X_SIZE_H 4 DA(P31) DS_InX_MARGINE 131 DA(P32) DS_OutX_MARGINE 130 DA(P33) DS_InY_MARGINE 131 DA(P34) DS_OutY_MARGINE 130 DA(P35) MARGINE_POS_X 122 DA(P36) NOT USED 0 DA(P37) NOT USED 0 DA(P38) COAST_ENABLE 1 DA(P39) NOT USED 0 DA(P40) INTERLACE 0 DA(P41) DIN_CONTROL_0 3 DA(P42) NOT USED 0 DA(P43) ahstartL 230 DA(P44) ahwidthL 253 DA(P45) ahwidth-startH 48 DA(P46) VSYNC_CYCLE_L 57 DA(P47) VSYNC_CYCLE_H 3 DA(P48) NOT USED 0 DA(P49) NOT USED 0 DA(P50) NOT USED 0 DA(P51) NOT USED 0 DA(P52) NOT USED 0 DAQ:XGA 60Hz(FULL) DA(Q01) FB_COUNTER1 56 DA(Q02) FB_COUNTER2 5 DA(Q03) VCO_DIVIDE 1 DA(Q04) DELAY 38 DA(Q05) CHARGE_PUMP 19 DA(Q06) AMP MODE 4 DA(Q07) OUTPUT MODE 2 DA(Q08) OPLL_MDIV_L 46 DA(Q09) OPLL_MDIV_H 0 DA(Q10) OPLL_NDIV 18 DA(Q11) INPUT_ACT_LINE_START_L 26 DA(Q12) INPUT_ACT_LINE_START_H 0 DA(Q13) INPUT_ACT_LINES_L 4 DA(Q14) INPUT_ACT_LINES_H 3 DA(Q15) INPUT_ACT_PIXEL_START_L 225 DA(Q16) INPUT_ACT_PIXEL_START_H 0 DA(Q17) INPUT_ACT_PIXELS_L 0 DA(Q18) INPUT_ACT_PIXELS_H 4 DA(Q19) NOT USED 0 DA(Q20) NOT USED 0 DA(Q21) WIN_X_MARGINE 162 DA(Q22) WIN_Y_MARGINE 132 DA(Q23) WIN_Y_POSI_L 1 DA(Q24) WIN_Y_POSI_H 0
Setting
value
Setting No. Setting item
DA(Q25) WIN_Y_SIZE_L 4 DA(Q26) WIN_Y_SIZE_H 3 DA(Q27) WIN_X_POSI_L 1 DA(Q28) WIN_X_POSI_H 0 DA(Q29) WIN_X_SIZE_L 94 DA(Q30) WIN_X_SIZE_H 5 DA(Q31) DS_InX_MARGINE 131 DA(Q32) DS_OutX_MARGINE 130 DA(Q33) DS_InY_MARGINE 131 DA(Q34) DS_OutY_MARGINE 130 DA(Q35) MARGINE_POS_X 122 DA(Q36) NOT USED 0 DA(Q37) NOT USED 0 DA(Q38) COAST_ENABLE 1 DA(Q39) NOT USED 0 DA(Q40) INTERLACE 0 DA(Q41) DIN_CONTROL_0 3 DA(Q42) NOT USED 0 DA(Q43) ahstartL 0 DA(Q44) ahwidthL 255 DA(Q45) ahwidth-startH 240 DA(Q46) VSYNC_CYCLE_L 57 DA(Q47) VSYNC_CYCLE_H 3 DA(Q48) NOT USED 0 DA(Q49) NOT USED 0 DA(Q50) NOT USED 0 DA(Q51) NOT USED 0 DA(Q52) NOT USED 0 DAR:XGA 70Hz(REGULAR) DA(R01) FB_COUNTER1 40 DA(R02) FB_COUNTER2 5 DA(R03) VCO_DIVIDE 1 DA(R04) DELAY 36 DA(R05) CHARGE_PUMP 20 DA(R06) AMP MODE 4 DA(R07) OUTPUT MODE 2 DA(R08) OPLL_MDIV_L 46 DA(R09) OPLL_MDIV_H 0 DA(R10) OPLL_NDIV 18 DA(R11) INPUT_ACT_LINE_START_L 26 DA(R12) INPUT_ACT_LINE_START_H 0 DA(R13) INPUT_ACT_LINES_L 4 DA(R14) INPUT_ACT_LINES_H 3 DA(R15) INPUT_ACT_PIXEL_START_L 204 DA(R16) INPUT_ACT_PIXEL_START_H 0 DA(R17) INPUT_ACT_PIXELS_L 0 DA(R18) INPUT_ACT_PIXELS_H 4 DA(R19) NOT USED 0 DA(R20) NOT USED 0 DA(R21) WIN_X_MARGINE 158 DA(R22) WIN_Y_MARGINE 130 DA(R23) WIN_Y_POSI_L 1 DA(R24) WIN_Y_POSI_H 0 DA(R25) WIN_Y_SIZE_L 4 DA(R26) WIN_Y_SIZE_H 3
Setting
value
(No.YA067)1-51
Page 52
Setting No. Setting item
DA(R27) WIN_X_POSI_L 175 DA(R28) WIN_X_POSI_H 0 DA(R29) WIN_X_SIZE_L 0 DA(R30) WIN_X_SIZE_H 4 DA(R31) DS_InX_MARGINE 131 DA(R32) DS_OutX_MARGINE 130 DA(R33) DS_InY_MARGINE 131 DA(R34) DS_OutY_MARGINE 130 DA(R35) MARGINE_POS_X 122 DA(R36) NOT USED 0 DA(R37) NOT USED 0 DA(R38) COAST_ENABLE 1 DA(R39) NOT USED 0 DA(R40) INTERLACE 0 DA(R41) DIN_CONTROL_0 3 DA(R42) NOT USED 0 DA(R43) ahstartL 230 DA(R44) ahwidthL 253 DA(R45) ahwidth-startH 48 DA(R46) VSYNC_CYCLE_L 57 DA(R47) VSYNC_CYCLE_H 3 DA(R48) NOT USED 0 DA(R49) NOT USED 0 DA(R50) NOT USED 0 DA(R51) NOT USED 0 DA(R52) NOT USED 0 DAS:XGA 70Hz(FULL) DA(S01) FB_COUNTER1 40 DA(S02) FB_COUNTER2 5 DA(S03) VCO_DIVIDE 1 DA(S04) DELAY 35 DA(S05) CHARGE_PUMP 20 DA(S06) AMP MODE 4 DA(S07) OUTPUT MODE 2 DA(S08) OPLL_MDIV_L 46 DA(S09) OPLL_MDIV_H 0 DA(S10) OPLL_NDIV 18 DA(S11) INPUT_ACT_LINE_START_L 26 DA(S12) INPUT_ACT_LINE_START_H 0 DA(S13) INPUT_ACT_LINES_L 4 DA(S14) INPUT_ACT_LINES_H 3 DA(S15) INPUT_ACT_PIXEL_START_L 204 DA(S16) INPUT_ACT_PIXEL_START_H 0 DA(S17) INPUT_ACT_PIXELS_L 0 DA(S18) INPUT_ACT_PIXELS_H 4 DA(S19) NOT USED 0 DA(S20) NOT USED 0 DA(S21) WIN_X_MARGINE 158 DA(S22) WIN_Y_MARGINE 130 DA(S23) WIN_Y_POSI_L 1 DA(S24) WIN_Y_POSI_H 0 DA(S25) WIN_Y_SIZE_L 4 DA(S26) WIN_Y_SIZE_H 3 DA(S27) WIN_X_POSI_L 1 DA(S28) WIN_X_POSI_H 0
Setting
value
Setting No. Setting item
DA(S29) WIN_X_SIZE_L 94 DA(S30) WIN_X_SIZE_H 5 DA(S31) DS_InX_MARGINE 131 DA(S32) DS_OutX_MARGINE 130 DA(S33) DS_InY_MARGINE 131 DA(S34) DS_OutY_MARGINE 130 DA(S35) MARGINE_POS_X 122 DA(S36) NOT USED 0 DA(S37) NOT USED 0 DA(S38) COAST_ENABLE 1 DA(S39) NOT USED 0 DA(S40) INTERLACE 0 DA(S41) DIN_CONTROL_0 3 DA(S42) NOT USED 0 DA(S43) ahstartL 0 DA(S44) ahwidthL 255 DA(S45) ahwidth-startH 240 DA(S46) VSYNC_CYCLE_L 57 DA(S47) VSYNC_CYCLE_H 3 DA(S48) NOT USED 0 DA(S49) NOT USED 0 DA(S50) NOT USED 0 DA(S51) NOT USED 0 DA(S52) NOT USED 0 DAT:XGA 75Hz(REGULAR) DA(T01) FB_COUNTER1 24 DA(T02) FB_COUNTER2 5 DA(T03) VCO_DIVIDE 1 DA(T04) DELAY 45 DA(T05) CHARGE_PUMP 21 DA(T06) AMP MODE 4 DA(T07) OUTPUT MODE 2 DA(T08) OPLL_MDIV_L 46 DA(T09) OPLL_MDIV_H 0 DA(T10) OPLL_NDIV 18 DA(T11) INPUT_ACT_LINE_START_L 25 DA(T12) INPUT_ACT_LINE_START_H 0 DA(T13) INPUT_ACT_LINES_L 4 DA(T14) INPUT_ACT_LINES_H 3 DA(T15) INPUT_ACT_PIXEL_START_L 194 DA(T16) INPUT_ACT_PIXEL_START_H 0 DA(T17) INPUT_ACT_PIXELS_L 0 DA(T18) INPUT_ACT_PIXELS_H 4 DA(T19) NOT USED 0 DA(T20) NOT USED 0 DA(T21) WIN_X_MARGINE 163 DA(T22) WIN_Y_MARGINE 128 DA(T23) WIN_Y_POSI_L 1 DA(T24) WIN_Y_POSI_H 0 DA(T25) WIN_Y_SIZE_L 4 DA(T26) WIN_Y_SIZE_H 3 DA(T27) WIN_X_POSI_L 175 DA(T28) WIN_X_POSI_H 0 DA(T29) WIN_X_SIZE_L 0 DA(T30) WIN_X_SIZE_H 4
Setting
value
1-52 (No.YA067)
Page 53
Setting No. Setting item
DA(T31) DS_InX_MARGINE 131 DA(T32) DS_OutX_MARGINE 130 DA(T33) DS_InY_MARGINE 131 DA(T34) DS_OutY_MARGINE 130 DA(T35) MARGINE_POS_X 122 DA(T36) NOT USED 0 DA(T37) NOT USED 0 DA(T38) COAST_ENABLE 1 DA(T39) NOT USED 0 DA(T40) INTERLACE 0 DA(T41) DIN_CONTROL_0 3 DA(T42) NOT USED 0 DA(T43) ahstartL 230 DA(T44) ahwidthL 253 DA(T45) ahwidth-startH 48 DA(T46) VSYNC_CYCLE_L 57 DA(T47) VSYNC_CYCLE_H 3 DA(T48) NOT USED 0 DA(T49) NOT USED 0 DA(T50) NOT USED 0 DA(T51) NOT USED 0 DA(T52) NOT USED 0 DAU:XGA 75Hz(FULL) DA(U01) FB_COUNTER1 24 DA(U02) FB_COUNTER2 5 DA(U03) VCO_DIVIDE 1 DA(U04) DELAY 45 DA(U05) CHARGE_PUMP 21 DA(U06) AMP MODE 4 DA(U07) OUTPUT MODE 2 DA(U08) OPLL_MDIV_L 46 DA(U09) OPLL_MDIV_H 0 DA(U10) OPLL_NDIV 18 DA(U11) INPUT_ACT_LINE_START_L 25 DA(U12) INPUT_ACT_LINE_START_H 0 DA(U13) INPUT_ACT_LINES_L 4 DA(U14) INPUT_ACT_LINES_H 3 DA(U15) INPUT_ACT_PIXEL_START_L 194 DA(U16) INPUT_ACT_PIXEL_START_H 0 DA(U17) INPUT_ACT_PIXELS_L 0 DA(U18) INPUT_ACT_PIXELS_H 4 DA(U19) NOT USED 0 DA(U20) NOT USED 0 DA(U21) WIN_X_MARGINE 163 DA(U22) WIN_Y_MARGINE 129 DA(U23) WIN_Y_POSI_L 1 DA(U24) WIN_Y_POSI_H 0 DA(U25) WIN_Y_SIZE_L 4 DA(U26) WIN_Y_SIZE_H 3 DA(U27) WIN_X_POSI_L 1 DA(U28) WIN_X_POSI_H 0 DA(U29) WIN_X_SIZE_L 94 DA(U30) WIN_X_SIZE_H 5 DA(U31) DS_InX_MARGINE 131 DA(U32) DS_OutX_MARGINE 130
Setting
value
Setting No. Setting item
DA(U33) DS_InY_MARGINE 131 DA(U34) DS_OutY_MARGINE 130 DA(U35) MARGINE_POS_X 122 DA(U36) NOT USED 0 DA(U37) NOT USED 0 DA(U38) COAST_ENABLE 1 DA(U39) NOT USED 0 DA(U40) INTERLACE 0 DA(U41) DIN_CONTROL_0 3 DA(U42) NOT USED 0 DA(U43) ahstartL 0 DA(U44) ahwidthL 255 DA(U45) ahwidth-startH 240 DA(U46) VSYNC_CYCLE_L 57 DA(U47) VSYNC_CYCLE_H 3 DA(U48) NOT USED 0 DA(U49) NOT USED 0 DA(U50) NOT USED 0 DA(U51) NOT USED 0 DA(U52) NOT USED 0 DAV:XGA 85Hz(REGULAR) DA(V01) FB_COUNTER1 88 DA(V02) FB_COUNTER2 5 DA(V03) VCO_DIVIDE 0 DA(V04) DELAY 23 DA(V05) CHARGE_PUMP 18 DA(V06) AMP MODE 4 DA(V07) OUTPUT MODE 2 DA(V08) OPLL_MDIV_L 46 DA(V09) OPLL_MDIV_H 0 DA(V10) OPLL_NDIV 18 DA(V11) INPUT_ACT_LINE_START_L 33 DA(V12) INPUT_ACT_LINE_START_H 0 DA(V13) INPUT_ACT_LINES_L 4 DA(V14) INPUT_ACT_LINES_H 3 DA(V15) INPUT_ACT_PIXEL_START_L 219 DA(V16) INPUT_ACT_PIXEL_START_H 0 DA(V17) INPUT_ACT_PIXELS_L 0 DA(V18) INPUT_ACT_PIXELS_H 4 DA(V19) NOT USED 0 DA(V20) NOT USED 0 DA(V21) WIN_X_MARGINE 163 DA(V22) WIN_Y_MARGINE 128 DA(V23) WIN_Y_POSI_L 1 DA(V24) WIN_Y_POSI_H 0 DA(V25) WIN_Y_SIZE_L 4 DA(V26) WIN_Y_SIZE_H 3 DA(V27) WIN_X_POSI_L 175 DA(V28) WIN_X_POSI_H 0 DA(V29) WIN_X_SIZE_L 0 DA(V30) WIN_X_SIZE_H 4 DA(V31) DS_InX_MARGINE 131 DA(V32) DS_OutX_MARGINE 130 DA(V33) DS_InY_MARGINE 131 DA(V34) DS_OutY_MARGINE 130
Setting
value
(No.YA067)1-53
Page 54
Setting No. Setting item
DA(V35) MARGINE_POS_X 122 DA(V36) NOT USED 0 DA(V37) NOT USED 0 DA(V38) COAST_ENABLE 1 DA(V39) NOT USED 0 DA(V40) INTERLACE 0 DA(V41) DIN_CONTROL_0 3 DA(V42) NOT USED 0 DA(V43) ahstartL 230 DA(V44) ahwidthL 253 DA(V45) ahwidth-startH 48 DA(V46) VSYNC_CYCLE_L 57 DA(V47) VSYNC_CYCLE_H 3 DA(V48) NOT USED 0 DA(V49) NOT USED 0 DA(V50) NOT USED 0 DA(V51) NOT USED 0 DA(V52) NOT USED 0 DAW:XGA 85Hz(FULL) DA(W01) FB_COUNTER1 88 DA(W02) FB_COUNTER2 5 DA(W03) VCO_DIVIDE 0 DA(W04) DELAY 24 DA(W05) CHARGE_PUMP 18 DA(W06) AMP MODE 4 DA(W07) OUTPUT MODE 2 DA(W08) OPLL_MDIV_L 46 DA(W09) OPLL_MDIV_H 0 DA(W10) OPLL_NDIV 18 DA(W11) INPUT_ACT_LINE_START_L 33 DA(W12) INPUT_ACT_LINE_START_H 0 DA(W13) INPUT_ACT_LINES_L 4 DA(W14) INPUT_ACT_LINES_H 3 DA(W15) INPUT_ACT_PIXEL_START_L 218 DA(W16) INPUT_ACT_PIXEL_START_H 0 DA(W17) INPUT_ACT_PIXELS_L 0 DA(W18) INPUT_ACT_PIXELS_H 4 DA(W19) NOT USED 0 DA(W20) NOT USED 0 DA(W21) WIN_X_MARGINE 163 DA(W22) WIN_Y_MARGINE 128 DA(W23) WIN_Y_POSI_L 1 DA(W24) WIN_Y_POSI_H 0 DA(W25) WIN_Y_SIZE_L 4 DA(W26) WIN_Y_SIZE_H 3 DA(W27) WIN_X_POSI_L 1 DA(W28) WIN_X_POSI_H 0 DA(W29) WIN_X_SIZE_L 94 DA(W30) WIN_X_SIZE_H 5 DA(W31) DS_InX_MARGINE 131 DA(W32) DS_OutX_MARGINE 130 DA(W33) DS_InY_MARGINE 131 DA(W34) DS_OutY_MARGINE 130 DA(W35) MARGINE_POS_X 122 DA(W36) NOT USED 0
Setting
value
Setting No. Setting item
DA(W37) NOT USED 0 DA(W38) COAST_ENABLE 1 DA(W39) NOT USED 0 DA(W40) INTERLACE 0 DA(W41) DIN_CONTROL_0 3 DA(W42) NOT USED 0 DA(W43) ahstartL 0 DA(W44) ahwidthL 255 DA(W45) ahwidth-startH 240 DA(W46) VSYNC_CYCLE_L 57 DA(W47) VSYNC_CYCLE_H 3 DA(W48) NOT USED 0 DA(W49) NOT USED 0 DA(W50) NOT USED 0 DA(W51) NOT USED 0 DA(W52) NOT USED 0 DAX:XGA+ 75Hz(REGULAR) DA(X01) FB_COUNTER1 56 DA(X02) FB_COUNTER2 6 DA(X03) VCO_DIVIDE 0 DA(X04) DELAY 42 DA(X05) CHARGE_PUMP 18 DA(X06) AMP MODE 4 DA(X07) OUTPUT MODE 2 DA(X08) OPLL_MDIV_L 46 DA(X09) OPLL_MDIV_H 0 DA(X10) OPLL_NDIV 18 DA(X11) INPUT_ACT_LINE_START_L 29 DA(X12) INPUT_ACT_LINE_START_H 0 DA(X13) INPUT_ACT_LINES_L 100 DA(X14) INPUT_ACT_LINES_H 3 DA(X15) INPUT_ACT_PIXEL_START_L 36 DA(X16) INPUT_ACT_PIXEL_START_H 1 DA(X17) INPUT_ACT_PIXELS_L 128 DA(X18) INPUT_ACT_PIXELS_H 4 DA(X19) NOT USED 0 DA(X20) NOT USED 0 DA(X21) WIN_X_MARGINE 163 DA(X22) WIN_Y_MARGINE 128 DA(X23) WIN_Y_POSI_L 1 DA(X24) WIN_Y_POSI_H 0 DA(X25) WIN_Y_SIZE_L 4 DA(X26) WIN_Y_SIZE_H 3 DA(X27) WIN_X_POSI_L 175 DA(X28) WIN_X_POSI_H 0 DA(X29) WIN_X_SIZE_L 0 DA(X30) WIN_X_SIZE_H 4 DA(X31) DS_InX_MARGINE 131 DA(X32) DS_OutX_MARGINE 130 DA(X33) DS_InY_MARGINE 131 DA(X34) DS_OutY_MARGINE 130 DA(X35) MARGINE_POS_X 122 DA(X36) NOT USED 0 DA(X37) NOT USED 0 DA(X38) COAST_ENABLE 1
Setting
value
1-54 (No.YA067)
Page 55
Setting No. Setting item
DA(X39) NOT USED 0 DA(X40) INTERLACE 0 DA(X41) DIN_CONTROL_0 3 DA(X42) NOT USED 0 DA(X43) ahstartL 230 DA(X44) ahwidthL 253 DA(X45) ahwidth-startH 48 DA(X46) VSYNC_CYCLE_L 57 DA(X47) VSYNC_CYCLE_H 3 DA(X48) NOT USED 0 DA(X49) NOT USED 0 DA(X50) NOT USED 0 DA(X51) NOT USED 0 DA(X52) NOT USED 0 DAY:XGA+ 75Hz(FULL) DA(Y01) FB_COUNTER1 56 DA(Y02) FB_COUNTER2 6 DA(Y03) VCO_DIVIDE 0 DA(Y04) DELAY 36 DA(Y05) CHARGE_PUMP 18 DA(Y06) AMP MODE 4 DA(Y07) OUTPUT MODE 2 DA(Y08) OPLL_MDIV_L 46 DA(Y09) OPLL_MDIV_H 0 DA(Y10) OPLL_NDIV 18 DA(Y11) INPUT_ACT_LINE_START_L 29 DA(Y12) INPUT_ACT_LINE_START_H 0 DA(Y13) INPUT_ACT_LINES_L 100 DA(Y14) INPUT_ACT_LINES_H 3 DA(Y15) INPUT_ACT_PIXEL_START_L 34 DA(Y16) INPUT_ACT_PIXEL_START_H 1 DA(Y17) INPUT_ACT_PIXELS_L 128 DA(Y18) INPUT_ACT_PIXELS_H 4 DA(Y19) NOT USED 0 DA(Y20) NOT USED 0 DA(Y21) WIN_X_MARGINE 163 DA(Y22) WIN_Y_MARGINE 128 DA(Y23) WIN_Y_POSI_L 1 DA(Y24) WIN_Y_POSI_H 0 DA(Y25) WIN_Y_SIZE_L 4 DA(Y26) WIN_Y_SIZE_H 3 DA(Y27) WIN_X_POSI_L 1 DA(Y28) WIN_X_POSI_H 0 DA(Y29) WIN_X_SIZE_L 94 DA(Y30) WIN_X_SIZE_H 5 DA(Y31) DS_InX_MARGINE 131 DA(Y32) DS_OutX_MARGINE 130 DA(Y33) DS_InY_MARGINE 131 DA(Y34) DS_OutY_MARGINE 130 DA(Y35) MARGINE_POS_X 122 DA(Y36) NOT USED 0 DA(Y37) NOT USED 0 DA(Y38) COAST_ENABLE 1 DA(Y39) NOT USED 0 DA(Y40) INTERLACE 0
Setting
value
Setting No. Setting item
DA(Y41) DIN_CONTROL_0 3 DA(Y42) NOT USED 0 DA(Y43) ahstartL 0 DA(Y44) ahwidthL 255 DA(Y45) ahwidth-startH 240 DA(Y46) VSYNC_CYCLE_L 57 DA(Y47) VSYNC_CYCLE_H 3 DA(Y48) NOT USED 0 DA(Y49) NOT USED 0 DA(Y50) NOT USED 0 DA(Y51) NOT USED 0 DA(Y52) NOT USED 0 DAZ:SXGA 60Hz(REGULAR) DA(Z01) FB_COUNTER1 56 DA(Z02) FB_COUNTER2 6 DA(Z03) VCO_DIVIDE 0 DA(Z04) DELAY 32 DA(Z05) CHARGE_PUMP 18 DA(Z06) AMP MODE 4 DA(Z07) OUTPUT MODE 2 DA(Z08) OPLL_MDIV_L 46 DA(Z09) OPLL_MDIV_H 0 DA(Z10) OPLL_NDIV 18 DA(Z11) INPUT_ACT_LINE_START_L 34 DA(Z12) INPUT_ACT_LINE_START_H 0 DA(Z13) INPUT_ACT_LINES_L 6 DA(Z14) INPUT_ACT_LINES_H 4 DA(Z15) INPUT_ACT_PIXEL_START_L 254 DA(Z16) INPUT_ACT_PIXEL_START_H 0 DA(Z17) INPUT_ACT_PIXELS_L 186 DA(Z18) INPUT_ACT_PIXELS_H 4 DA(Z19) NOT USED 0 DA(Z20) NOT USED 0 DA(Z21) WIN_X_MARGINE 163 DA(Z22) WIN_Y_MARGINE 127 DA(Z23) WIN_Y_POSI_L 1 DA(Z24) WIN_Y_POSI_H 0 DA(Z25) WIN_Y_SIZE_L 4 DA(Z26) WIN_Y_SIZE_H 3 DA(Z27) WIN_X_POSI_L 175 DA(Z28) WIN_X_POSI_H 0 DA(Z29) WIN_X_SIZE_L 0 DA(Z30) WIN_X_SIZE_H 4 DA(Z31) DS_InX_MARGINE 131 DA(Z32) DS_OutX_MARGINE 130 DA(Z33) DS_InY_MARGINE 131 DA(Z34) DS_OutY_MARGINE 130 DA(Z35) MARGINE_POS_X 122 DA(Z36) NOT USED 0 DA(Z37) NOT USED 0 DA(Z38) COAST_ENABLE 1 DA(Z39) NOT USED 0 DA(Z40) INTERLACE 0 DA(Z41) DIN_CONTROL_0 3 DA(Z42) NOT USED 0
Setting
value
(No.YA067)1-55
Page 56
Setting No. Setting item
DA(Z43) ahstartL 230 DA(Z44) ahwidthL 253 DA(Z45) ahwidth-startH 48 DA(Z46) VSYNC_CYCLE_L 57 DA(Z47) VSYNC_CYCLE_H 3 DA(Z48) NOT USED 0 DA(Z49) NOT USED 0 DA(Z50) NOT USED 0 DA(Z51) NOT USED 0 DA(Z52) NOT USED 0 DBA:SXGA 60Hz(FULL) DB(A01) FB_COUNTER1 56 DB(A02) FB_COUNTER2 6 DB(A03) VCO_DIVIDE 0 DB(A04) DELAY 33 DB(A05) CHARGE_PUMP 18 DB(A06) AMP MODE 4 DB(A07) OUTPUT MODE 2 DB(A08) OPLL_MDIV_L 46 DB(A09) OPLL_MDIV_H 0 DB(A10) OPLL_NDIV 18 DB(A11) INPUT_ACT_LINE_START_L 34 DB(A12) INPUT_ACT_LINE_START_H 0 DB(A13) INPUT_ACT_LINES_L 6 DB(A14) INPUT_ACT_LINES_H 4 DB(A15) INPUT_ACT_PIXEL_START_L 253 DB(A16) INPUT_ACT_PIXEL_START_H 0 DB(A17) INPUT_ACT_PIXELS_L 191 DB(A18) INPUT_ACT_PIXELS_H 4 DB(A19) NOT USED 0 DB(A20) NOT USED 0 DB(A21) WIN_X_MARGINE 163 DB(A22) WIN_Y_MARGINE 127 DB(A23) WIN_Y_POSI_L 1 DB(A24) WIN_Y_POSI_H 0 DB(A25) WIN_Y_SIZE_L 4 DB(A26) WIN_Y_SIZE_H 3 DB(A27) WIN_X_POSI_L 1 DB(A28) WIN_X_POSI_H 0 DB(A29) WIN_X_SIZE_L 94 DB(A30) WIN_X_SIZE_H 5 DB(A31) DS_InX_MARGINE 131 DB(A32) DS_OutX_MARGINE 130 DB(A33) DS_InY_MARGINE 131 DB(A34) DS_OutY_MARGINE 130 DB(A35) MARGINE_POS_X 122 DB(A36) NOT USED 0 DB(A37) NOT USED 0 DB(A38) COAST_ENABLE 1 DB(A39) NOT USED 0 DB(A40) INTERLACE 0 DB(A41) DIN_CONTROL_0 3 DB(A42) NOT USED 0 DB(A43) ahstartL 0 DB(A44) ahwidthL 255
Setting
value
Setting No. Setting item
DB(A45) ahwidth-startH 240 DB(A46) VSYNC_CYCLE_L 57 DB(A47) VSYNC_CYCLE_H 3 DB(A48) NOT USED 0 DB(A49) NOT USED 0 DB(A50) NOT USED 0 DB(A51) NOT USED 0 DB(A52) NOT USED 0 DBB:SXGA 75Hz(REGULAR) DB(B01) FB_COUNTER1 56 DB(B02) FB_COUNTER2 6 DB(B03) VCO_DIVIDE 0 DB(B04) DELAY 32 DB(B05) CHARGE_PUMP 19 DB(B06) AMP MODE 4 DB(B07) OUTPUT MODE 2 DB(B08) OPLL_MDIV_L 46 DB(B09) OPLL_MDIV_H 0 DB(B10) OPLL_NDIV 18 DB(B11) INPUT_ACT_LINE_START_L 34 DB(B12) INPUT_ACT_LINE_START_H 0 DB(B13) INPUT_ACT_LINES_L 7 DB(B14) INPUT_ACT_LINES_H 4 DB(B15) INPUT_ACT_PIXEL_START_L 16 DB(B16) INPUT_ACT_PIXEL_START_H 1 DB(B17) INPUT_ACT_PIXELS_L 184 DB(B18) INPUT_ACT_PIXELS_H 4 DB(B19) NOT USED 0 DB(B20) NOT USED 0 DB(B21) WIN_X_MARGINE 163 DB(B22) WIN_Y_MARGINE 127 DB(B23) WIN_Y_POSI_L 1 DB(B24) WIN_Y_POSI_H 0 DB(B25) WIN_Y_SIZE_L 4 DB(B26) WIN_Y_SIZE_H 3 DB(B27) WIN_X_POSI_L 175 DB(B28) WIN_X_POSI_H 0 DB(B29) WIN_X_SIZE_L 0 DB(B30) WIN_X_SIZE_H 4 DB(B31) DS_InX_MARGINE 131 DB(B32) DS_OutX_MARGINE 130 DB(B33) DS_InY_MARGINE 131 DB(B34) DS_OutY_MARGINE 130 DB(B35) MARGINE_POS_X 122 DB(B36) NOT USED 0 DB(B37) NOT USED 0 DB(B38) COAST_ENABLE 1 DB(B39) NOT USED 0 DB(B40) INTERLACE 0 DB(B41) DIN_CONTROL_0 3 DB(B42) NOT USED 0 DB(B43) ahstartL 230 DB(B44) ahwidthL 253 DB(B45) ahwidth-startH 48 DB(B46) VSYNC_CYCLE_L 57
Setting
value
1-56 (No.YA067)
Page 57
Setting No. Setting item
DB(B47) VSYNC_CYCLE_H 3 DB(B48) NOT USED 0 DB(B49) NOT USED 0 DB(B50) NOT USED 0 DB(B51) NOT USED 0 DB(B52) NOT USED 0 DBC:SXGA 75Hz(FULL) DB(C01) FB_COUNTER1 56 DB(C02) FB_COUNTER2 6 DB(C03) VCO_DIVIDE 0 DB(C04) DELAY 30 DB(C05) CHARGE_PUMP 19 DB(C06) AMP MODE 4 DB(C07) OUTPUT MODE 2 DB(C08) OPLL_MDIV_L 46 DB(C09) OPLL_MDIV_H 0 DB(C10) OPLL_NDIV 18 DB(C11) INPUT_ACT_LINE_START_L 34 DB(C12) INPUT_ACT_LINE_START_H 0 DB(C13) INPUT_ACT_LINES_L 6 DB(C14) INPUT_ACT_LINES_H 4 DB(C15) INPUT_ACT_PIXEL_START_L 13 DB(C16) INPUT_ACT_PIXEL_START_H 1 DB(C17) INPUT_ACT_PIXELS_L 190 DB(C18) INPUT_ACT_PIXELS_H 4 DB(C19) NOT USED 0 DB(C20) NOT USED 0 DB(C21) WIN_X_MARGINE 163 DB(C22) WIN_Y_MARGINE 128 DB(C23) WIN_Y_POSI_L 1 DB(C24) WIN_Y_POSI_H 0 DB(C25) WIN_Y_SIZE_L 4 DB(C26) WIN_Y_SIZE_H 3 DB(C27) WIN_X_POSI_L 1 DB(C28) WIN_X_POSI_H 0 DB(C29) WIN_X_SIZE_L 94 DB(C30) WIN_X_SIZE_H 5 DB(C31) DS_InX_MARGINE 131 DB(C32) DS_OutX_MARGINE 130 DB(C33) DS_InY_MARGINE 131 DB(C34) DS_OutY_MARGINE 130 DB(C35) MARGINE_POS_X 122 DB(C36) NOT USED 0 DB(C37) NOT USED 0 DB(C38) COAST_ENABLE 1 DB(C39) NOT USED 0 DB(C40) INTERLACE 0 DB(C41) DIN_CONTROL_0 3 DB(C42) NOT USED 0 DB(C43) ahstartL 0 DB(C44) ahwidthL 255 DB(C45) ahwidth-startH 240 DB(C46) VSYNC_CYCLE_L 57 DB(C47) VSYNC_CYCLE_H 3 DB(C48) NOT USED 0
Setting
value
Setting No. Setting item
DB(C49) NOT USED 0 DB(C50) NOT USED 0 DB(C51) NOT USED 0 DB(C52) NOT USED 0 DBD:UXGA 60Hz(REGULAR) DB(D01) FB_COUNTER1 56 DB(D02) FB_COUNTER2 6 DB(D03) VCO_DIVIDE 0 DB(D04) DELAY 30 DB(D05) CHARGE_PUMP 19 DB(D06) AMP MODE 4 DB(D07) OUTPUT MODE 2 DB(D08) OPLL_MDIV_L 46 DB(D09) OPLL_MDIV_H 0 DB(D10) OPLL_NDIV 18 DB(D11) INPUT_ACT_LINE_START_L 41 DB(D12) INPUT_ACT_LINE_START_H 0 DB(D13) INPUT_ACT_LINES_L 183 DB(D14) INPUT_ACT_LINES_H 4 DB(D15) INPUT_ACT_PIXEL_START_L 15 DB(D16) INPUT_ACT_PIXEL_START_H 1 DB(D17) INPUT_ACT_PIXELS_L 156 DB(D18) INPUT_ACT_PIXELS_H 4 DB(D19) NOT USED 0 DB(D20) NOT USED 0 DB(D21) WIN_X_MARGINE 163 DB(D22) WIN_Y_MARGINE 128 DB(D23) WIN_Y_POSI_L 1 DB(D24) WIN_Y_POSI_H 0 DB(D25) WIN_Y_SIZE_L 4 DB(D26) WIN_Y_SIZE_H 3 DB(D27) WIN_X_POSI_L 175 DB(D28) WIN_X_POSI_H 0 DB(D29) WIN_X_SIZE_L 0 DB(D30) WIN_X_SIZE_H 4 DB(D31) DS_InX_MARGINE 131 DB(D32) DS_OutX_MARGINE 130 DB(D33) DS_InY_MARGINE 131 DB(D34) DS_OutY_MARGINE 130 DB(D35) MARGINE_POS_X 122 DB(D36) NOT USED 0 DB(D37) NOT USED 0 DB(D38) COAST_ENABLE 1 DB(D39) NOT USED 0 DB(D40) INTERLACE 0 DB(D41) DIN_CONTROL_0 3 DB(D42) NOT USED 0 DB(D43) ahstartL 230 DB(D44) ahwidthL 253 DB(D45) ahwidth-startH 48 DB(D46) VSYNC_CYCLE_L 57 DB(D47) VSYNC_CYCLE_H 3 DB(D48) NOT USED 0 DB(D49) NOT USED 0 DB(D50) NOT USED 0
Setting
value
(No.YA067)1-57
Page 58
Setting No. Setting item
DB(D51) NOT USED 0 DB(D52) NOT USED 0 DBE:UXGA 60Hz(FULL) DB(E01) FB_COUNTER1 56 DB(E02) FB_COUNTER2 6 DB(E03) VCO_DIVIDE 0 DB(E04) DELAY 34 DB(E05) CHARGE_PUMP 19 DB(E06) AMP MODE 4 DB(E07) OUTPUT MODE 2 DB(E08) OPLL_MDIV_L 46 DB(E09) OPLL_MDIV_H 0 DB(E10) OPLL_NDIV 18 DB(E11) INPUT_ACT_LINE_START_L 41 DB(E12) INPUT_ACT_LINE_START_H 0 DB(E13) INPUT_ACT_LINES_L 183 DB(E14) INPUT_ACT_LINES_H 4 DB(E15) INPUT_ACT_PIXEL_START_L 13 DB(E16) INPUT_ACT_PIXEL_START_H 1 DB(E17) INPUT_ACT_PIXELS_L 161 DB(E18) INPUT_ACT_PIXELS_H 4 DB(E19) NOT USED 0 DB(E20) NOT USED 0 DB(E21) WIN_X_MARGINE 163 DB(E22) WIN_Y_MARGINE 128 DB(E23) WIN_Y_POSI_L 1 DB(E24) WIN_Y_POSI_H 0 DB(E25) WIN_Y_SIZE_L 4 DB(E26) WIN_Y_SIZE_H 3 DB(E27) WIN_X_POSI_L 1 DB(E28) WIN_X_POSI_H 0 DB(E29) WIN_X_SIZE_L 94 DB(E30) WIN_X_SIZE_H 5 DB(E31) DS_InX_MARGINE 131 DB(E32) DS_OutX_MARGINE 130 DB(E33) DS_InY_MARGINE 131 DB(E34) DS_OutY_MARGINE 130 DB(E35) MARGINE_POS_X 122 DB(E36) NOT USED 0 DB(E37) NOT USED 0 DB(E38) COAST_ENABLE 1 DB(E39) NOT USED 0 DB(E40) INTERLACE 0 DB(E41) DIN_CONTROL_0 3 DB(E42) NOT USED 0 DB(E43) ahstartL 0 DB(E44) ahwidthL 255 DB(E45) ahwidth-startH 240 DB(E46) VSYNC_CYCLE_L 57 DB(E47) VSYNC_CYCLE_H 3 DB(E48) NOT USED 0 DB(E49) NOT USED 0 DB(E50) NOT USED 0 DB(E51) NOT USED 0 DB(E52) NOT USED 0
Setting
value
Setting No. Setting item
DBF:UXGA 65Hz(REGULAR) DB(F01) FB_COUNTER1 56 DB(F02) FB_COUNTER2 6 DB(F03) VCO_DIVIDE 0 DB(F04) DELAY 32 DB(F05) CHARGE_PUMP 19 DB(F06) AMP MODE 4 DB(F07) OUTPUT MODE 2 DB(F08) OPLL_MDIV_L 46 DB(F09) OPLL_MDIV_H 0 DB(F10) OPLL_NDIV 18 DB(F11) INPUT_ACT_LINE_START_L 41 DB(F12) INPUT_ACT_LINE_START_H 0 DB(F13) INPUT_ACT_LINES_L 184 DB(F14) INPUT_ACT_LINES_H 4 DB(F15) INPUT_ACT_PIXEL_START_L 10 DB(F16) INPUT_ACT_PIXEL_START_H 1 DB(F17) INPUT_ACT_PIXELS_L 156 DB(F18) INPUT_ACT_PIXELS_H 4 DB(F19) NOT USED 0 DB(F20) NOT USED 0 DB(F21) WIN_X_MARGINE 163 DB(F22) WIN_Y_MARGINE 126 DB(F23) WIN_Y_POSI_L 1 DB(F24) WIN_Y_POSI_H 0 DB(F25) WIN_Y_SIZE_L 4 DB(F26) WIN_Y_SIZE_H 3 DB(F27) WIN_X_POSI_L 175 DB(F28) WIN_X_POSI_H 0 DB(F29) WIN_X_SIZE_L 0 DB(F30) WIN_X_SIZE_H 4 DB(F31) DS_InX_MARGINE 131 DB(F32) DS_OutX_MARGINE 130 DB(F33) DS_InY_MARGINE 131 DB(F34) DS_OutY_MARGINE 130 DB(F35) MARGINE_POS_X 122 DB(F36) NOT USED 0 DB(F37) NOT USED 0 DB(F38) COAST_ENABLE 1 DB(F39) NOT USED 0 DB(F40) INTERLACE 0 DB(F41) DIN_CONTROL_0 3 DB(F42) NOT USED 0 DB(F43) ahstartL 230 DB(F44) ahwidthL 253 DB(F45) ahwidth-startH 48 DB(F46) VSYNC_CYCLE_L 57 DB(F47) VSYNC_CYCLE_H 3 DB(F48) NOT USED 0 DB(F49) NOT USED 0 DB(F50) NOT USED 0 DB(F51) NOT USED 0 DB(F52) NOT USED 0 DBG:UXGA 65Hz(FULL) DB(G01) FB_COUNTER1 56
Setting
value
1-58 (No.YA067)
Page 59
Setting No. Setting item
DB(G02) FB_COUNTER2 6 DB(G03) VCO_DIVIDE 0 DB(G04) DELAY 32 DB(G05) CHARGE_PUMP 19 DB(G06) AMP MODE 4 DB(G07) OUTPUT MODE 2 DB(G08) OPLL_MDIV_L 46 DB(G09) OPLL_MDIV_H 0 DB(G10) OPLL_NDIV 18 DB(G11) INPUT_ACT_LINE_START_L 41 DB(G12) INPUT_ACT_LINE_START_H 0 DB(G13) INPUT_ACT_LINES_L 184 DB(G14) INPUT_ACT_LINES_H 4 DB(G15) INPUT_ACT_PIXEL_START_L 8 DB(G16) INPUT_ACT_PIXEL_START_H 1 DB(G17) INPUT_ACT_PIXELS_L 161 DB(G18) INPUT_ACT_PIXELS_H 4 DB(G19) NOT USED 0 DB(G20) NOT USED 0 DB(G21) WIN_X_MARGINE 163 DB(G22) WIN_Y_MARGINE 126 DB(G23) WIN_Y_POSI_L 1 DB(G24) WIN_Y_POSI_H 0 DB(G25) WIN_Y_SIZE_L 4 DB(G26) WIN_Y_SIZE_H 3 DB(G27) WIN_X_POSI_L 1 DB(G28) WIN_X_POSI_H 0 DB(G29) WIN_X_SIZE_L 94 DB(G30) WIN_X_SIZE_H 5 DB(G31) DS_InX_MARGINE 131 DB(G32) DS_OutX_MARGINE 130 DB(G33) DS_InY_MARGINE 131 DB(G34) DS_OutY_MARGINE 130 DB(G35) MARGINE_POS_X 122 DB(G36) NOT USED 0 DB(G37) NOT USED 0 DB(G38) COAST_ENABLE 1 DB(G39) NOT USED 0 DB(G40) INTERLACE 0 DB(G41) DIN_CONTROL_0 3 DB(G42) NOT USED 0 DB(G43) ahstartL 0 DB(G44) ahwidthL 255 DB(G45) ahwidth-startH 240 DB(G46) VSYNC_CYCLE_L 57 DB(G47) VSYNC_CYCLE_H 3 DB(G48) NOT USED 0 DB(G49) NOT USED 0 DB(G50) NOT USED 0 DB(G51) NOT USED 0 DB(G52) NOT USED 0 DBH:UXGA 70Hz(REGULAR) DB(H01) FB_COUNTER1 92 DB(H02) FB_COUNTER2 5 DB(H03) VCO_DIVIDE 0
Setting
value
Setting No. Setting item
DB(H04) DELAY 32 DB(H05) CHARGE_PUMP 19 DB(H06) AMP MODE 4 DB(H07) OUTPUT MODE 2 DB(H08) OPLL_MDIV_L 46 DB(H09) OPLL_MDIV_H 0 DB(H10) OPLL_NDIV 18 DB(H11) INPUT_ACT_LINE_START_L 41 DB(H12) INPUT_ACT_LINE_START_H 0 DB(H13) INPUT_ACT_LINES_L 184 DB(H14) INPUT_ACT_LINES_H 4 DB(H15) INPUT_ACT_PIXEL_START_L 221 DB(H16) INPUT_ACT_PIXEL_START_H 0 DB(H17) INPUT_ACT_PIXELS_L 249 DB(H18) INPUT_ACT_PIXELS_H 3 DB(H19) NOT USED 0 DB(H20) NOT USED 0 DB(H21) WIN_X_MARGINE 163 DB(H22) WIN_Y_MARGINE 126 DB(H23) WIN_Y_POSI_L 1 DB(H24) WIN_Y_POSI_H 0 DB(H25) WIN_Y_SIZE_L 4 DB(H26) WIN_Y_SIZE_H 3 DB(H27) WIN_X_POSI_L 175 DB(H28) WIN_X_POSI_H 0 DB(H29) WIN_X_SIZE_L 0 DB(H30) WIN_X_SIZE_H 4 DB(H31) DS_InX_MARGINE 131 DB(H32) DS_OutX_MARGINE 130 DB(H33) DS_InY_MARGINE 131 DB(H34) DS_OutY_MARGINE 130 DB(H35) MARGINE_POS_X 122 DB(H36) NOT USED 0 DB(H37) NOT USED 0 DB(H38) COAST_ENABLE 1 DB(H39) NOT USED 0 DB(H40) INTERLACE 0 DB(H41) DIN_CONTROL_0 3 DB(H42) NOT USED 0 DB(H43) ahstartL 230 DB(H44) ahwidthL 253 DB(H45) ahwidth-startH 48 DB(H46) VSYNC_CYCLE_L 57 DB(H47) VSYNC_CYCLE_H 3 DB(H48) NOT USED 0 DB(H49) NOT USED 0 DB(H50) NOT USED 0 DB(H51) NOT USED 0 DB(H52) NOT USED 0 DBI:UXGA 70Hz(FULL) DB(I01) FB_COUNTER1 92 DB(I02) FB_COUNTER2 5 DB(I03) VCO_DIVIDE 0 DB(I04) DELAY 26 DB(I05) CHARGE_PUMP 19
Setting
value
(No.YA067)1-59
Page 60
Setting No. Setting item
DB(I06) AMP MODE 4 DB(I07) OUTPUT MODE 2 DB(I08) OPLL_MDIV_L 46 DB(I09) OPLL_MDIV_H 0 DB(I10) OPLL_NDIV 18 DB(I11) INPUT_ACT_LINE_START_L 41 DB(I12) INPUT_ACT_LINE_START_H 0 DB(I13) INPUT_ACT_LINES_L 184 DB(I14) INPUT_ACT_LINES_H 4 DB(I15) INPUT_ACT_PIXEL_START_L 218 DB(I16) INPUT_ACT_PIXEL_START_H 0 DB(I17) INPUT_ACT_PIXELS_L 254 DB(I18) INPUT_ACT_PIXELS_H 3 DB(I19) NOT USED 0 DB(I20) NOT USED 0 DB(I21) WIN_X_MARGINE 163 DB(I22) WIN_Y_MARGINE 126 DB(I23) WIN_Y_POSI_L 1 DB(I24) WIN_Y_POSI_H 0 DB(I25) WIN_Y_SIZE_L 4 DB(I26) WIN_Y_SIZE_H 3 DB(I27) WIN_X_POSI_L 1 DB(I28) WIN_X_POSI_H 0 DB(I29) WIN_X_SIZE_L 94 DB(I30) WIN_X_SIZE_H 5 DB(I31) DS_InX_MARGINE 131 DB(I32) DS_OutX_MARGINE 130 DB(I33) DS_InY_MARGINE 131 DB(I34) DS_OutY_MARGINE 130 DB(I35) MARGINE_POS_X 122 DB(I36) NOT USED 0 DB(I37) NOT USED 0 DB(I38) COAST_ENABLE 1 DB(I39) NOT USED 0 DB(I40) INTERLACE 0 DB(I41) DIN_CONTROL_0 3 DB(I42) NOT USED 0 DB(I43) ahstartL 0 DB(I44) ahwidthL 255 DB(I45) ahwidth-startH 240 DB(I46) VSYNC_CYCLE_L 57 DB(I47) VSYNC_CYCLE_H 3 DB(I48) NOT USED 0 DB(I49) NOT USED 0 DB(I50) NOT USED 0 DB(I51) NOT USED 0 DB(I52) NOT USED 0 DBJ:MAC16(REGULAR) DB(J01) FB_COUNTER1 120 DB(J02) FB_COUNTER2 4 DB(J03) VCO_DIVIDE 1 DB(J04) DELAY 36 DB(J05) CHARGE_PUMP 19 DB(J06) AMP MODE 4 DB(J07) OUTPUT MODE 2
Setting
value
Setting No. Setting item
DB(J08) OPLL_MDIV_L 46 DB(J09) OPLL_MDIV_H 0 DB(J10) OPLL_NDIV 18 DB(J11) INPUT_ACT_LINE_START_L 36 DB(J12) INPUT_ACT_LINE_START_H 0 DB(J13) INPUT_ACT_LINES_L 116 DB(J14) INPUT_ACT_LINES_H 2 DB(J15) INPUT_ACT_PIXEL_START_L 223 DB(J16) INPUT_ACT_PIXEL_START_H 0 DB(J17) INPUT_ACT_PIXELS_L 61 DB(J18) INPUT_ACT_PIXELS_H 3 DB(J19) NOT USED 0 DB(J20) NOT USED 0 DB(J21) WIN_X_MARGINE 163 DB(J22) WIN_Y_MARGINE 128 DB(J23) WIN_Y_POSI_L 1 DB(J24) WIN_Y_POSI_H 0 DB(J25) WIN_Y_SIZE_L 4 DB(J26) WIN_Y_SIZE_H 3 DB(J27) WIN_X_POSI_L 175 DB(J28) WIN_X_POSI_H 0 DB(J29) WIN_X_SIZE_L 0 DB(J30) WIN_X_SIZE_H 4 DB(J31) DS_InX_MARGINE 131 DB(J32) DS_OutX_MARGINE 130 DB(J33) DS_InY_MARGINE 131 DB(J34) DS_OutY_MARGINE 130 DB(J35) MARGINE_POS_X 122 DB(J36) NOT USED 0 DB(J37) NOT USED 0 DB(J38) COAST_ENABLE 1 DB(J39) NOT USED 0 DB(J40) INTERLACE 0 DB(J41) DIN_CONTROL_0 3 DB(J42) NOT USED 0 DB(J43) ahstartL 230 DB(J44) ahwidthL 253 DB(J45) ahwidth-startH 48 DB(J46) VSYNC_CYCLE_L 57 DB(J47) VSYNC_CYCLE_H 3 DB(J48) NOT USED 0 DB(J49) NOT USED 0 DB(J50) NOT USED 0 DB(J51) NOT USED 0 DB(J52) NOT USED 0 DBK:MAC16(FULL) DB(K01) FB_COUNTER1 120 DB(K02) FB_COUNTER2 4 DB(K03) VCO_DIVIDE 1 DB(K04) DELAY 36 DB(K05) CHARGE_PUMP 19 DB(K06) AMP MODE 4 DB(K07) OUTPUT MODE 2 DB(K08) OPLL_MDIV_L 46 DB(K09) OPLL_MDIV_H 0
Setting
value
1-60 (No.YA067)
Page 61
Setting No. Setting item
DB(K10) OPLL_NDIV 18 DB(K11) INPUT_ACT_LINE_START_L 36 DB(K12) INPUT_ACT_LINE_START_H 0 DB(K13) INPUT_ACT_LINES_L 116 DB(K14) INPUT_ACT_LINES_H 2 DB(K15) INPUT_ACT_PIXEL_START_L 221 DB(K16) INPUT_ACT_PIXEL_START_H 0 DB(K17) INPUT_ACT_PIXELS_L 63 DB(K18) INPUT_ACT_PIXELS_H 3 DB(K19) NOT USED 0 DB(K20) NOT USED 0 DB(K21) WIN_X_MARGINE 163 DB(K22) WIN_Y_MARGINE 128 DB(K23) WIN_Y_POSI_L 1 DB(K24) WIN_Y_POSI_H 0 DB(K25) WIN_Y_SIZE_L 4 DB(K26) WIN_Y_SIZE_H 3 DB(K27) WIN_X_POSI_L 1 DB(K28) WIN_X_POSI_H 0 DB(K29) WIN_X_SIZE_L 94 DB(K30) WIN_X_SIZE_H 5 DB(K31) DS_InX_MARGINE 131 DB(K32) DS_OutX_MARGINE 130 DB(K33) DS_InY_MARGINE 131 DB(K34) DS_OutY_MARGINE 130 DB(K35) MARGINE_POS_X 122 DB(K36) NOT USED 0 DB(K37) NOT USED 0 DB(K38) COAST_ENABLE 1 DB(K39) NOT USED 0 DB(K40) INTERLACE 0 DB(K41) DIN_CONTROL_0 3 DB(K42) NOT USED 0 DB(K43) ahstartL 0 DB(K44) ahwidthL 255 DB(K45) ahwidth-startH 240 DB(K46) VSYNC_CYCLE_L 57 DB(K47) VSYNC_CYCLE_H 3 DB(K48) NOT USED 0 DB(K49) NOT USED 0 DB(K50) NOT USED 0 DB(K51) NOT USED 0 DB(K52) NOT USED 0 DBL:MAC19(REGULAR) DB(L01) FB_COUNTER1 40 DB(L02) FB_COUNTER2 5 DB(L03) VCO_DIVIDE 0 DB(L04) DELAY 32 DB(L05) CHARGE_PUMP 17 DB(L06) AMP MODE 4 DB(L07) OUTPUT MODE 2 DB(L08) OPLL_MDIV_L 46 DB(L09) OPLL_MDIV_H 0 DB(L10) OPLL_NDIV 18 DB(L11) INPUT_ACT_LINE_START_L 33
Setting
value
Setting No. Setting item
DB(L12) INPUT_ACT_LINE_START_H 0 DB(L13) INPUT_ACT_LINES_L 0 DB(L14) INPUT_ACT_LINES_H 3 DB(L15) INPUT_ACT_PIXEL_START_L 220 DB(L16) INPUT_ACT_PIXEL_START_H 0 DB(L17) INPUT_ACT_PIXELS_L 0 DB(L18) INPUT_ACT_PIXELS_H 4 DB(L19) NOT USED 0 DB(L20) NOT USED 0 DB(L21) WIN_X_MARGINE 168 DB(L22) WIN_Y_MARGINE 130 DB(L23) WIN_Y_POSI_L 1 DB(L24) WIN_Y_POSI_H 0 DB(L25) WIN_Y_SIZE_L 4 DB(L26) WIN_Y_SIZE_H 3 DB(L27) WIN_X_POSI_L 175 DB(L28) WIN_X_POSI_H 0 DB(L29) WIN_X_SIZE_L 0 DB(L30) WIN_X_SIZE_H 4 DB(L31) DS_InX_MARGINE 131 DB(L32) DS_OutX_MARGINE 130 DB(L33) DS_InY_MARGINE 131 DB(L34) DS_OutY_MARGINE 130 DB(L35) MARGINE_POS_X 122 DB(L36) NOT USED 0 DB(L37) NOT USED 0 DB(L38) COAST_ENABLE 1 DB(L39) NOT USED 0 DB(L40) INTERLACE 0 DB(L41) DIN_CONTROL_0 3 DB(L42) NOT USED 0 DB(L43) ahstartL 230 DB(L44) ahwidthL 253 DB(L45) ahwidth-startH 48 DB(L46) VSYNC_CYCLE_L 57 DB(L47) VSYNC_CYCLE_H 3 DB(L48) NOT USED 0 DB(L49) NOT USED 0 DB(L50) NOT USED 0 DB(L51) NOT USED 0 DB(L52) NOT USED 0 DBM:MAC19(FULL) DB(M01) FB_COUNTER1 40 DB(M02) FB_COUNTER2 5 DB(M03) VCO_DIVIDE 0 DB(M04) DELAY 32 DB(M05) CHARGE_PUMP 17 DB(M06) AMP MODE 4 DB(M07) OUTPUT MODE 2 DB(M08) OPLL_MDIV_L 46 DB(M09) OPLL_MDIV_H 0 DB(M10) OPLL_NDIV 18 DB(M11) INPUT_ACT_LINE_START_L 32 DB(M12) INPUT_ACT_LINE_START_H 0 DB(M13) INPUT_ACT_LINES_L 0
Setting
value
(No.YA067)1-61
Page 62
Setting No. Setting item
DB(M14) INPUT_ACT_LINES_H 3 DB(M15) INPUT_ACT_PIXEL_START_L 220 DB(M16) INPUT_ACT_PIXEL_START_H 0 DB(M17) INPUT_ACT_PIXELS_L 0 DB(M18) INPUT_ACT_PIXELS_H 4 DB(M19) NOT USED 0 DB(M20) NOT USED 0 DB(M21) WIN_X_MARGINE 168 DB(M22) WIN_Y_MARGINE 130 DB(M23) WIN_Y_POSI_L 1 DB(M24) WIN_Y_POSI_H 0 DB(M25) WIN_Y_SIZE_L 4 DB(M26) WIN_Y_SIZE_H 3 DB(M27) WIN_X_POSI_L 1 DB(M28) WIN_X_POSI_H 0 DB(M29) WIN_X_SIZE_L 94 DB(M30) WIN_X_SIZE_H 5 DB(M31) DS_InX_MARGINE 131 DB(M32) DS_OutX_MARGINE 130 DB(M33) DS_InY_MARGINE 131 DB(M34) DS_OutY_MARGINE 130 DB(M35) MARGINE_POS_X 122 DB(M36) NOT USED 0 DB(M37) NOT USED 0 DB(M38) COAST_ENABLE 1 DB(M39) NOT USED 0 DB(M40) INTERLACE 0 DB(M41) DIN_CONTROL_0 3 DB(M42) NOT USED 0 DB(M43) ahstartL 0 DB(M44) ahwidthL 255 DB(M45) ahwidth-startH 240 DB(M46) VSYNC_CYCLE_L 57 DB(M47) VSYNC_CYCLE_H 3 DB(M48) NOT USED 0 DB(M49) NOT USED 0 DB(M50) NOT USED 0 DB(M51) NOT USED 0 DB(M52) NOT USED 0 DBN:MAC21(REGULAR) DB(N01) FB_COUNTER1 168 DB(N02) FB_COUNTER2 5 DB(N03) VCO_DIVIDE 0 DB(N04) DELAY 30 DB(N05) CHARGE_PUMP 18 DB(N06) AMP MODE 4 DB(N07) OUTPUT MODE 2 DB(N08) OPLL_MDIV_L 46 DB(N09) OPLL_MDIV_H 0 DB(N10) OPLL_NDIV 18 DB(N11) INPUT_ACT_LINE_START_L 36 DB(N12) INPUT_ACT_LINE_START_H 0 DB(N13) INPUT_ACT_LINES_L 107 DB(N14) INPUT_ACT_LINES_H 3 DB(N15) INPUT_ACT_PIXEL_START_L 185
Setting
value
Setting No. Setting item
DB(N16) INPUT_ACT_PIXEL_START_H 0 DB(N17) INPUT_ACT_PIXELS_L 124 DB(N18) INPUT_ACT_PIXELS_H 4 DB(N19) NOT USED 0 DB(N20) NOT USED 0 DB(N21) WIN_X_MARGINE 163 DB(N22) WIN_Y_MARGINE 128 DB(N23) WIN_Y_POSI_L 1 DB(N24) WIN_Y_POSI_H 0 DB(N25) WIN_Y_SIZE_L 4 DB(N26) WIN_Y_SIZE_H 3 DB(N27) WIN_X_POSI_L 175 DB(N28) WIN_X_POSI_H 0 DB(N29) WIN_X_SIZE_L 0 DB(N30) WIN_X_SIZE_H 4 DB(N31) DS_InX_MARGINE 131 DB(N32) DS_OutX_MARGINE 130 DB(N33) DS_InY_MARGINE 131 DB(N34) DS_OutY_MARGINE 130 DB(N35) MARGINE_POS_X 122 DB(N36) NOT USED 0 DB(N37) NOT USED 0 DB(N38) COAST_ENABLE 1 DB(N39) NOT USED 0 DB(N40) INTERLACE 0 DB(N41) DIN_CONTROL_0 3 DB(N42) NOT USED 0 DB(N43) ahstartL 230 DB(N44) ahwidthL 253 DB(N45) ahwidth-startH 48 DB(N46) VSYNC_CYCLE_L 57 DB(N47) VSYNC_CYCLE_H 3 DB(N48) NOT USED 0 DB(N49) NOT USED 0 DB(N50) NOT USED 0 DB(N51) NOT USED 0 DB(N52) NOT USED 0 DBO:MAC21(FULL) DB(O01) FB_COUNTER1 168 DB(O02) FB_COUNTER2 5 DB(O03) VCO_DIVIDE 0 DB(O04) DELAY 26 DB(O05) CHARGE_PUMP 18 DB(O06) AMP MODE 4 DB(O07) OUTPUT MODE 2 DB(O08) OPLL_MDIV_L 46 DB(O09) OPLL_MDIV_H 0 DB(O10) OPLL_NDIV 18 DB(O11) INPUT_ACT_LINE_START_L 35 DB(O12) INPUT_ACT_LINE_START_H 0 DB(O13) INPUT_ACT_LINES_L 107 DB(O14) INPUT_ACT_LINES_H 3 DB(O15) INPUT_ACT_PIXEL_START_L 183 DB(O16) INPUT_ACT_PIXEL_START_H 0 DB(O17) INPUT_ACT_PIXELS_L 129
Setting
value
1-62 (No.YA067)
Page 63
Setting No. Setting item
DB(O18) INPUT_ACT_PIXELS_H 4 DB(O19) NOT USED 0 DB(O20) NOT USED 0 DB(O21) WIN_X_MARGINE 163 DB(O22) WIN_Y_MARGINE 128 DB(O23) WIN_Y_POSI_L 1 DB(O24) WIN_Y_POSI_H 0 DB(O25) WIN_Y_SIZE_L 4 DB(O26) WIN_Y_SIZE_H 3 DB(O27) WIN_X_POSI_L 1 DB(O28) WIN_X_POSI_H 0 DB(O29) WIN_X_SIZE_L 94 DB(O30) WIN_X_SIZE_H 5 DB(O31) DS_InX_MARGINE 131 DB(O32) DS_OutX_MARGINE 130 DB(O33) DS_InY_MARGINE 131 DB(O34) DS_OutY_MARGINE 130 DB(O35) MARGINE_POS_X 122 DB(O36) NOT USED 0 DB(O37) NOT USED 0 DB(O38) COAST_ENABLE 1 DB(O39) NOT USED 0 DB(O40) INTERLACE 0 DB(O41) DIN_CONTROL_0 3 DB(O42) NOT USED 0 DB(O43) ahstartL 0 DB(O44) ahwidthL 255 DB(O45) ahwidth-startH 240 DB(O46) VSYNC_CYCLE_L 57 DB(O47) VSYNC_CYCLE_H 3 DB(O48) NOT USED 0 DB(O49) NOT USED 0 DB(O50) NOT USED 0 DB(O51) NOT USED 0 DBO52 NOT USED 0 DBO:RGB 15k/60Hz(REGULAR) DB(P01) FB_COUNTER1 82 DB(P02) FB_COUNTER2 3 DB(P03) VCO_DIVIDE 3 DB(P04) DELAY 32 DB(P05) CHARGE_PUMP 18 DB(P06) AMP MODE 4 DB(P07) OUTPUT MODE 2 DB(P08) OPLL_MDIV_L 46 DB(P09) OPLL_MDIV_H 0 DB(P10) OPLL_NDIV 18 DB(P11) INPUT_ACT_LINE_START_L 18 DB(P12) INPUT_ACT_LINE_START_H 0 DB(P13) INPUT_ACT_LINES_L 230 DB(P14) INPUT_ACT_LINES_H 0 DB(P15) INPUT_ACT_PIXEL_START_L 103 DB(P16) INPUT_ACT_PIXEL_START_H 0 DB(P17) INPUT_ACT_PIXELS_L 163 DB(P18) INPUT_ACT_PIXELS_H 2 DB(P19) NOT USED 0
Setting
value
Setting No. Setting item
DB(P20) NOT USED 0 DB(P21) WIN_X_MARGINE 151 DB(P22) WIN_Y_MARGINE 136 DB(P23) WIN_Y_POSI_L 1 DB(P24) WIN_Y_POSI_H 0 DB(P25) WIN_Y_SIZE_L 4 DB(P26) WIN_Y_SIZE_H 3 DB(P27) WIN_X_POSI_L 175 DB(P28) WIN_X_POSI_H 0 DB(P29) WIN_X_SIZE_L 0 DB(P30) WIN_X_SIZE_H 4 DB(P31) DS_InX_MARGINE 131 DB(P32) DS_OutX_MARGINE 130 DB(P33) DS_InY_MARGINE 131 DB(P34) DS_OutY_MARGINE 130 DB(P35) MARGINE_POS_X 122 DB(P36) NOT USED 0 DB(P37) NOT USED 0 DB(P38) COAST_ENABLE 1 DB(P39) NOT USED 0 DB(P40) INTERLACE 1 DB(P41) DIN_CONTROL_0 3 DB(P42) NOT USED 0 DB(P43) ahstartL 230 DB(P44) ahwidthL 253 DB(P45) ahwidth-startH 48 DB(P46) VSYNC_CYCLE_L 57 DB(P47) VSYNC_CYCLE_H 3 DB(P48) NOT USED 0 DB(P49) NOT USED 0 DB(P50) NOT USED 0 DB(P51) NOT USED 0 DB(P52) NOT USED 0 DBQ:RGB 15k/60Hz(FULL) DB(Q01) FB_COUNTER1 82 DB(Q02) FB_COUNTER2 3 DB(Q03) VCO_DIVIDE 3 DB(Q04) DELAY 32 DB(Q05) CHARGE_PUMP 18 DB(Q06) AMP MODE 4 DB(Q07) OUTPUT MODE 2 DB(Q08) OPLL_MDIV_L 46 DB(Q09) OPLL_MDIV_H 0 DB(Q10) OPLL_NDIV 18 DB(Q11) INPUT_ACT_LINE_START_L 18 DB(Q12) INPUT_ACT_LINE_START_H 0 DB(Q13) INPUT_ACT_LINES_L 230 DB(Q14) INPUT_ACT_LINES_H 0 DB(Q15) INPUT_ACT_PIXEL_START_L 101 DB(Q16) INPUT_ACT_PIXEL_START_H 0 DB(Q17) INPUT_ACT_PIXELS_L 167 DB(Q18) INPUT_ACT_PIXELS_H 2 DB(Q19) NOT USED 0 DB(Q20) NOT USED 0 DB(Q21) WIN_X_MARGINE 151
Setting
value
(No.YA067)1-63
Page 64
Setting No. Setting item
DB(Q22) WIN_Y_MARGINE 136 DB(Q23) WIN_Y_POSI_L 1 DB(Q24) WIN_Y_POSI_H 0 DB(Q25) WIN_Y_SIZE_L 4 DB(Q26) WIN_Y_SIZE_H 3 DB(Q27) WIN_X_POSI_L 1 DB(Q28) WIN_X_POSI_H 0 DB(Q29) WIN_X_SIZE_L 94 DB(Q30) WIN_X_SIZE_H 5 DB(Q31) DS_InX_MARGINE 131 DB(Q32) DS_OutX_MARGINE 130 DB(Q33) DS_InY_MARGINE 131 DB(Q34) DS_OutY_MARGINE 130 DB(Q35) MARGINE_POS_X 122 DB(Q36) NOT USED 0 DB(Q37) NOT USED 0 DB(Q38) COAST_ENABLE 0 DB(Q39) NOT USED 0 DB(Q40) INTERLACE 1 DB(Q41) DIN_CONTROL_0 3 DB(Q42) NOT USED 0 DB(Q43) ahstartL 0 DB(Q44) ahwidthL 255 DB(Q45) ahwidth-startH 240 DB(Q46) VSYNC_CYCLE_L 57 DB(Q47) VSYNC_CYCLE_H 3 DB(Q48) NOT USED 0 DB(Q49) NOT USED 0 DB(Q50) NOT USED 0 DB(Q51) NOT USED 0 DB(Q52) NOT USED 0 DBR:RGB 15k/60Hz(ZOOM) DB(R01) FB_COUNTER1 82 DB(R02) FB_COUNTER2 3 DB(R03) VCO_DIVIDE 3 DB(R04) DELAY 32 DB(R05) CHARGE_PUMP 18 DB(R06) AMP MODE 4 DB(R07) OUTPUT MODE 2 DB(R08) OPLL_MDIV_L 46 DB(R09) OPLL_MDIV_H 0 DB(R10) OPLL_NDIV 18 DB(R11) INPUT_ACT_LINE_START_L 46 DB(R12) INPUT_ACT_LINE_START_H 0 DB(R13) INPUT_ACT_LINES_L 173 DB(R14) INPUT_ACT_LINES_H 0 DB(R15) INPUT_ACT_PIXEL_START_L 101 DB(R16) INPUT_ACT_PIXEL_START_H 0 DB(R17) INPUT_ACT_PIXELS_L 167 DB(R18) INPUT_ACT_PIXELS_H 2 DB(R19) NOT USED 0 DB(R20) NOT USED 0 DB(R21) WIN_X_MARGINE 151 DB(R22) WIN_Y_MARGINE 164 DB(R23) WIN_Y_POSI_L 1
Setting
value
Setting No. Setting item
DB(R24) WIN_Y_POSI_H 0 DB(R25) WIN_Y_SIZE_L 4 DB(R26) WIN_Y_SIZE_H 3 DB(R27) WIN_X_POSI_L 1 DB(R28) WIN_X_POSI_H 0 DB(R29) WIN_X_SIZE_L 94 DB(R30) WIN_X_SIZE_H 5 DB(R31) DS_InX_MARGINE 131 DB(R32) DS_OutX_MARGINE 130 DB(R33) DS_InY_MARGINE 131 DB(R34) DS_OutY_MARGINE 130 DB(R35) MARGINE_POS_X 122 DB(R36) NOT USED 0 DB(R37) NOT USED 0 DB(R38) COAST_ENABLE 0 DB(R39) NOT USED 0 DB(R40) INTERLACE 1 DB(R41) DIN_CONTROL_0 3 DB(R42) NOT USED 0 DB(R43) ahstartL 0 DB(R44) ahwidthL 255 DB(R45) ahwidth-startH 240 DB(R46) VSYNC_CYCLE_L 57 DB(R47) VSYNC_CYCLE_H 3 DB(R48) NOT USED 0 DB(R49) NOT USED 0 DB(R50) NOT USED 0 DB(R51) NOT USED 0 DB(R52) NOT USED 0 DBS:RGB 15k/60Hz(PANORAMIC) DB(S01) FB_COUNTER1 82 DB(S02) FB_COUNTER2 3 DB(S03) VCO_DIVIDE 3 DB(S04) DELAY 32 DB(S05) CHARGE_PUMP 18 DB(S06) AMP MODE 4 DB(S07) OUTPUT MODE 2 DB(S08) OPLL_MDIV_L 46 DB(S09) OPLL_MDIV_H 0 DB(S10) OPLL_NDIV 18 DB(S11) INPUT_ACT_LINE_START_L 24 DB(S12) INPUT_ACT_LINE_START_H 0 DB(S13) INPUT_ACT_LINES_L 218 DB(S14) INPUT_ACT_LINES_H 0 DB(S15) INPUT_ACT_PIXEL_START_L 101 DB(S16) INPUT_ACT_PIXEL_START_H 0 DB(S17) INPUT_ACT_PIXELS_L 172 DB(S18) INPUT_ACT_PIXELS_H 2 DB(S19) DS_OUTX_PANO_L 104 DB(S20) DS_OUTX_PANO_H 2 DB(S21) WIN_X_MARGINE 151 DB(S22) WIN_Y_MARGINE 142 DB(S23) WIN_Y_POSI_L 1 DB(S24) WIN_Y_POSI_H 0 DB(S25) WIN_Y_SIZE_L 4
Setting
value
1-64 (No.YA067)
Page 65
Setting No. Setting item
DB(S26) WIN_Y_SIZE_H 3 DB(S27) WIN_X_POSI_L 1 DB(S28) WIN_X_POSI_H 0 DB(S29) WIN_X_SIZE_L 94 DB(S30) WIN_X_SIZE_H 5 DB(S31) DS_InX_MARGINE 131 DB(S32) DS_OutX_MARGINE 130 DB(S33) DS_InY_MARGINE 131 DB(S34) DS_OutY_MARGINE 130 DB(S35) MARGINE_POS_X 122 DB(S36) NOT USED 0 DB(S37) NOT USED 0 DB(S38) COAST_ENABLE 0 DB(S39) NOT USED 0 DB(S40) INTERLACE 1 DB(S41) DIN_CONTROL_0 3 DB(S42) NOT USED 0 DB(S43) ahstartL 0 DB(S44) ahwidthL 255 DB(S45) ahwidth-startH 240 DB(S46) VSYNC_CYCLE_L 57 DB(S47) VSYNC_CYCLE_H 3 DB(S48) NOT USED 0 DB(S49) NOT USED 0 DB(S50) NOT USED 0 DB(S51) NOT USED 0 DB(S52) NOT USED 0 DBT:PC RGB 15k/50Hz(REGULAR) DB(T01) FB_COUNTER1 88 DB(T02) FB_COUNTER2 3 DB(T03) VCO_DIVIDE 3 DB(T04) DELAY 32 DB(T05) CHARGE_PUMP 18 DB(T06) AMP MODE 4 DB(T07) OUTPUT MODE 2 DB(T08) OPLL_MDIV_L 35 DB(T09) OPLL_MDIV_H 0 DB(T10) OPLL_NDIV 14 DB(T11) INPUT_ACT_LINE_START_L 24 DB(T12) INPUT_ACT_LINE_START_H 0 DB(T13) INPUT_ACT_LINES_L 18 DB(T14) INPUT_ACT_LINES_H 1 DB(T15) INPUT_ACT_PIXEL_START_L 117 DB(T16) INPUT_ACT_PIXEL_START_H 0 DB(T17) INPUT_ACT_PIXELS_L 150 DB(T18) INPUT_ACT_PIXELS_H 2 DB(T19) NOT USED 0 DB(T20) NOT USED 0 DB(T21) WIN_X_MARGINE 153 DB(T22) WIN_Y_MARGINE 137 DB(T23) WIN_Y_POSI_L 1 DB(T24) WIN_Y_POSI_H 0 DB(T25) WIN_Y_SIZE_L 4 DB(T26) WIN_Y_SIZE_H 3 DB(T27) WIN_X_POSI_L 175
Setting
value
Setting No. Setting item
DB(T28) WIN_X_POSI_H 0 DB(T29) WIN_X_SIZE_L 0 DB(T30) WIN_X_SIZE_H 4 DB(T31) DS_InX_MARGINE 131 DB(T32) DS_OutX_MARGINE 130 DB(T33) DS_InY_MARGINE 131 DB(T34) DS_OutY_MARGINE 130 DB(T35) MARGINE_POS_X 122 DB(T36) NOT USED 0 DB(T37) NOT USED 0 DB(T38) NOT USED 1 DB(T39) NOT USED 0 DB(T40) INTERLACE 1 DB(T41) DIN_CONTROL_0 3 DB(T42) NOT USED 0 DB(T43) ahstartL 230 DB(T44) ahwidthL 253 DB(T45) ahwidth-startH 48 DB(T46) VSYNC_CYCLE_L 192 DB(T47) VSYNC_CYCLE_H 3 DB(T48) NOT USED 0 DB(T49) NOT USED 0 DB(T50) NOT USED 0 DB(T51) NOT USED 0 DB(T52) NOT USED 0 DBU:PC RGB 15k/50Hz(ZOOM) DB(U01) FB_COUNTER1 88 DB(U02) FB_COUNTER2 3 DB(U03) VCO_DIVIDE 3 DB(U04) DELAY 32 DB(U05) CHARGE_PUMP 18 DB(U06) AMP MODE 4 DB(U07) OUTPUT MODE 2 DB(U08) OPLL_MDIV_L 35 DB(U09) OPLL_MDIV_H 0 DB(U10) OPLL_NDIV 14 DB(U11) INPUT_ACT_LINE_START_L 24 DB(U12) INPUT_ACT_LINE_START_H 0 DB(U13) INPUT_ACT_LINES_L 18 DB(U14) INPUT_ACT_LINES_H 1 DB(U15) INPUT_ACT_PIXEL_START_L 115 DB(U16) INPUT_ACT_PIXEL_START_H 0 DB(U17) INPUT_ACT_PIXELS_L 155 DB(U18) INPUT_ACT_PIXELS_H 2 DB(U19) NOT USED 0 DB(U20) NOT USED 0 DB(U21) WIN_X_MARGINE 153 DB(U22) WIN_Y_MARGINE 137 DB(U23) WIN_Y_POSI_L 1 DB(U24) WIN_Y_POSI_H 0 DB(U25) WIN_Y_SIZE_L 4 DB(U26) WIN_Y_SIZE_H 3 DB(U27) WIN_X_POSI_L 1 DB(U28) WIN_X_POSI_H 0 DB(U29) WIN_X_SIZE_L 94
Setting
value
(No.YA067)1-65
Page 66
Setting No. Setting item
DB(U30) WIN_X_SIZE_H 5 DB(U31) DS_InX_MARGINE 131 DB(U32) DS_OutX_MARGINE 130 DB(U33) DS_InY_MARGINE 131 DB(U34) DS_OutY_MARGINE 130 DB(U35) MARGINE_POS_X 122 DB(U36) NOT USED 0 DB(U37) NOT USED 0 DB(U38) COAST_ENABLE 0 DB(U39) NOT USED 0 DB(U40) INTERLACE 1 DB(U41) DIN_CONTROL_0 3 DB(U42) NOT USED 0 DB(U43) ahstartL 0 DB(U44) ahwidthL 255 DB(U45) ahwidth-startH 240 DB(U46) VSYNC_CYCLE_L 192 DB(U47) VSYNC_CYCLE_H 3 DB(U48) NOT USED 0 DB(U49) NOT USED 0 DB(U50) NOT USED 0 DB(U51) NOT USED 0 DB(U52) NOT USED 0 DBV:PC RGB 15k/50Hz(ZOOM) DB(V01) FB_COUNTER1 88 DB(V02) FB_COUNTER2 3 DB(V03) VCO_DIVIDE 3 DB(V04) DELAY 32 DB(V05) CHARGE_PUMP 18 DB(V06) AMP MODE 4 DB(V07) OUTPUT MODE 2 DB(V08) OPLL_MDIV_L 35 DB(V09) OPLL_MDIV_H 0 DB(V10) OPLL_NDIV 14 DB(V11) INPUT_ACT_LINE_START_L 58 DB(V12) INPUT_ACT_LINE_START_H 0 DB(V13) INPUT_ACT_LINES_L 205 DB(V14) INPUT_ACT_LINES_H 0 DB(V15) INPUT_ACT_PIXEL_START_L 115 DB(V16) INPUT_ACT_PIXEL_START_H 0 DB(V17) INPUT_ACT_PIXELS_L 155 DB(V18) INPUT_ACT_PIXELS_H 2 DB(V19) NOT USED 0 DB(V20) NOT USED 0 DB(V21) WIN_X_MARGINE 153 DB(V22) WIN_Y_MARGINE 173 DB(V23) WIN_Y_POSI_L 1 DB(V24) WIN_Y_POSI_H 0 DB(V25) WIN_Y_SIZE_L 4 DB(V26) WIN_Y_SIZE_H 3 DB(V27) WIN_X_POSI_L 1 DB(V28) WIN_X_POSI_H 0 DB(V29) WIN_X_SIZE_L 94 DB(V30) WIN_X_SIZE_H 5 DB(V31) DS_InX_MARGINE 131
Setting
value
Setting No. Setting item
DB(V32) DS_OutX_MARGINE 130 DB(V33) DS_InY_MARGINE 131 DB(V34) DS_OutY_MARGINE 130 DB(V35) MARGINE_POS_X 122 DB(V36) NOT USED 0 DB(V37) NOT USED 0 DB(V38) COAST_ENABLE 0 DB(V39) NOT USED 0 DB(V40) INTERLACE 1 DB(V41) DIN_CONTROL_0 3 DB(V42) NOT USED 0 DB(V43) ahstartL 0 DB(V44) ahwidthL 255 DB(V45) ahwidth-startH 240 DB(V46) VSYNC_CYCLE_L 192 DB(V47) VSYNC_CYCLE_H 3 DB(V48) NOT USED 0 DB(V49) NOT USED 0 DB(V50) NOT USED 0 DB(V51) NOT USED 0 DB(V52) NOT USED 0 DBW:PC RGB 15k/50Hz(PANORAMIC) DB(W01) FB_COUNTER1 88 DB(W02) FB_COUNTER2 3 DB(W03) VCO_DIVIDE 3 DB(W04) DELAY 32 DB(W05) CHARGE_PUMP 18 DB(W06) AMP MODE 4 DB(W07) OUTPUT MODE 2 DB(W08) OPLL_MDIV_L 35 DB(W09) OPLL_MDIV_H 0 DB(W10) OPLL_NDIV 14 DB(W11) INPUT_ACT_LINE_START_L 30 DB(W12) INPUT_ACT_LINE_START_H 0 DB(W13) INPUT_ACT_LINES_L 5 DB(W14) INPUT_ACT_LINES_H 1 DB(W15) INPUT_ACT_PIXEL_START_L 115 DB(W16) INPUT_ACT_PIXEL_START_H 0 DB(W17) INPUT_ACT_PIXELS_L 161 DB(W18) INPUT_ACT_PIXELS_H 2 DB(W19) DS_OUTX_PANO_L 104 DB(W20) DS_OUTX_PANO_H 2 DB(W21) WIN_X_MARGINE 155 DB(W22) WIN_Y_MARGINE 145 DB(W23) WIN_Y_POSI_L 1 DB(W24) WIN_Y_POSI_H 0 DB(W25) WIN_Y_SIZE_L 4 DB(W26) WIN_Y_SIZE_H 3 DB(W27) WIN_X_POSI_L 1 DB(W28) WIN_X_POSI_H 0 DB(W29) WIN_X_SIZE_L 94 DB(W30) WIN_X_SIZE_H 5 DB(W31) DS_InX_MARGINE 131 DB(W32) DS_OutX_MARGINE 130 DB(W33) DS_InY_MARGINE 131
Setting
value
1-66 (No.YA067)
Page 67
Setting No. Setting item
DB(W34) DS_OutY_MARGINE 130 DB(W35) MARGINE_POS_X 122 DB(W36) NOT USED 0 DB(W37) NOT USED 0 DB(W38) COAST_ENABLE 0 DB(W39) NOT USED 0 DB(W40) INTERLACE 1 DB(W41) DIN_CONTROL_0 3 DB(W42) NOT USED 0 DB(W43) ahstartL 0 DB(W44) ahwidthL 255 DB(W45) ahwidth-startH 240 DB(W46) VSYNC_CYCLE_L 192 DB(W47) VSYNC_CYCLE_H 3 DB(W48) NOT USED 0 DB(W49) NOT USED 0 DB(W50) NOT USED 0 DB(W51) NOT USED 0 DB(W52) NOT USED 0
Setting
value
(No.YA067)1-67
Page 68
H POSITION BLOCK
Setting No. Setting item
PA:VIDEO P(A01) NTSC REGULAR 0 P(A02) NTSC FULL 0 P(A03) NTSC ZOOM 0 P(A04) NTSC PANORAMA 0 P(A05) N443 REGULAR 0 P(A06) N443 FULL 0 P(A07) N443 ZOOM 0 P(A08) N443 PANORAMA 0 P(A09) PAL M REGULAR 0 P(A10) PAL M FULL 0 P(A11) PAL M ZOOM 0 P(A12) PAL M PANORAMA 0 P(A13) PAL60 REGULAR 0 P(A14) PAL60 FULL 0 P(A15) PAL60 ZOOM 0 P(A16) PAL60 PANORAMA 0 P(A17) BW60 REGULAR 0 P(A18) BW60 FULL 0 P(A19) BW60 ZOOM 0 P(A20) BW60 PANORAMA 0 P(A21) PAL REGULAR 0 P(A22) PAL FULL 0 P(A23) PAL ZOOM 0 P(A24) PAL PANORAMA 0 P(A25) PAL N REGULAR 0 P(A26) PAL N FULL 0 P(A27) PAL N ZOOM 0 P(A28) PAL N PANORAMA 0 P(A29) SECAM REGULAR 0 P(A30) SECAM FULL 0 P(A31) SECAM ZOOM 0 P(A32) SECAM PANORAMA 0 P(A33) BW50 REGULAR 0 P(A34) BW50 FULL 0 P(A35) BW50 ZOOM 0 P(A36) BW50 PANORAMA 0 PB:Y/C P(B01) NTSC REGULAR 0 P(B02) NTSC FULL 0 P(B03) NTSC ZOOM 0 P(B04) NTSC PANORAMA 0 P(B05) N443 REGULAR 0 P(B06) N443 FULL 0 P(B07) N443 ZOOM 0 P(B08) N443 PANORAMA 0 P(B09) PAL M REGULAR 0 P(B10) PAL M FULL 0 P(B11) PAL M ZOOM 0 P(B12) PAL M PANORAMA 0 P(B13) PAL60 REGULAR 0 P(B14) PAL60 FULL 0 P(B15) PAL60 ZOOM 0 P(B16) PAL60 PANORAMA 0
Setting
value
Setting No. Setting item
P(B17) BW60 REGULAR 0 P(B18) BW60 FULL 0 P(B19) BW60 ZOOM 0 P(B20) BW60 PANORAMA 0 P(B21) PAL REGULAR 0 P(B22) PAL FULL 0 P(B23) PAL ZOOM 0 P(B24) PAL PANORAMA 0 P(B25) PAL N REGULAR 0 P(B26) PAL N FULL 0 P(B27) PAL N ZOOM 0 P(B28) PAL N PANORAMA 0 P(B29) SECAM REGULAR 0 P(B30) SECAM FULL 0 P(B31) SECAM ZOOM 0 P(B32) SECAM PANORAMA 0 P(B33) BW50 REGULAR 0 P(B34) BW50 FULL 0 P(B35) BW50 ZOOM 0 P(B36) BW50 PANORAMA 0 PC:COMONENT P(C01) 480I REGULAR -25 P(C02) 480I FULL -24 P(C03) 480I ZOOM -24 P(C04) 480I PANORAMA -24 P(C05) 576I REGULAR -25 P(C06) 576I FULL -25 P(C07) 576I ZOOM -25 P(C08) 576I PANORAMA -25 P(C09) 480P REGULAR 0 P(C10) 480P FULL 0 P(C11) 480P ZOOM 0 P(C12) 480P PANORAMA 0 P(C13) 576P REGULAR 0 P(C14) 576P FULL 0 P(C15) 576P ZOOM 0 P(C16) 576P PANORAMA 0 P(C17) 720/60p FULL 0 P(C18) 720/50p FULL 0 P(C19) 1080/60i FULL 0 P(C20) 1080/50i FULL 0 P(C21) 1035i FULL 0 PD:RGB P(D01) RGB15K60 REGULAR 0 P(D02) RGB15K60 FULL 0 P(D03) RGB15K60 ZOOM 0 P(D04) RGB15K60 PANORAMA 0 P(D05) RGB15K50 REGULAR 0 P(D06) RGB15K50 FULL 0 P(D07) RGB15K50 ZOOM 0 P(D08) RGB15K50 PANORAMA 0 P(D09) VGA400/56 REGULAR 0 P(D10) VGA400/56 FULLÅ[ 0 P(D11) VGA400/70 REGULAR 0
Setting
value
1-68 (No.YA067)
Page 69
Setting No. Setting item
P(D12) VGA400/70 FULL 0 P(D13) VGA/60 REGULAR 0 P(D14) VGA/60 FULLÅ[ 0 P(D15) VGA/72 REGULAR 0 P(D16) VGA/72 FULL 0 P(D17) VGA/75 REGULAR 0 P(D18) VGA/75 FULL 0 P(D19) MAC13 REGULAR 0 P(D20) MAC13 FULL 0 P(D21) SVGA/56 REGULAR 0 P(D22) SVGA/56 FULL 0 P(D23) SVGA/60 REGULAR 0 P(D24) SVGA/60 FULL 0 P(D25) SVGA/72 REGULAR 0 P(D26) SVGA/72 FULL 0 P(D27) SVGA/75 REGULAR 0 P(D28) SVGA/75 FULL 0 P(D29) XGA/60 REGULAR 0 P(D30) XGA/60 FULL 0 P(D31) XGA/70 REGULAR 0 P(D32) XGA/70 FULL 0 P(D33) XGA/75 REGULAR 0 P(D34) XGA/75 FULL 0 P(D35) XGA/85 REGULAR 0 P(D36) XGA/85 FULL 0 P(D37) XGA+/75 REGULAR 0 P(D38) XGA+/75 FULL 0 P(D39) SXGA/60 REGULAR 0 P(D40) SXGA/60 FULL 0 P(D41) SXGA/75 REGULAR 0 P(D42) SXGA/75 FULL 0 P(D43) UXGA/60 REGULAR 0 P(D44) UXGA/60 FULL 0 P(D45) UXGA/65 REGULAR 0 P(D46) UXGA/65 FULL 0 P(D47) UXGA/70 REGULAR 0 P(D48) UXGA/70 FULL 0 P(D49) MAC16 REGULAR 0 P(D50) MAC16 FULL 0 P(D51) MAC19 REGULAR 0 P(D52) MAC19 FULL 0 P(D53) MAC21 REGULAR 0 P(D54) MAC21 FULL 0
Setting
value
(No.YA067)1-69
Page 70
PANEL BLOCK
Setting No. Setting item
B(A01) ERROR DIFFUSION 1 B(A02) DITHER 0 B(A03) CONTRARY GAMMA SELECT 1 B(A04) ERROR DIFFUSION NOISE
REDUCTION B(A05) NOT USED 0 B(A06) NOT USED 0 B(A07) NOT USED 0 B(A08) NOT USED 0 B(A09) NOT USED 0 B(A10) NOT USED 0 BB:COMPO.HD B(B01) ERROR DIFFUSION 1 B(B02) DITHER 0 B(B03) CONTRARY GAMMA SELECT 1 B(B04) ERROR DIFFUSION NOISE
REDUCTION B(B05) NOT USED 0 B(B06) NOT USED 0 B(B07) NOT USED 0 B(B08) NOT USED 0 B(B09) NOT USED 0 B(B10) NOT USED 0 BC:PC B(C01) ERROR DIFFUSION 1 B(C02) DITHER 0 B(C03) CONTRARY GAMMA SELECT 1 B(C04) ERROR DIFFUSION NOISE
REDUCTION B(C05) NOT USED 0 B(C06) NOT USED 0 B(C07) NOT USED 0 B(C08) NOT USED 0 B(C09) NOT USED 0 B(C10) NOT USED 0
Setting
value
0
0
1
1-70 (No.YA067)
Page 71
SIGNAL BLOCK
Setting No. Setting item
B(A01) ERROR DIFFUSION 1 SA:VIDEO-NTSC S(A01) LPF 0 S(A02) SUB BRIGHT 16 S(A03) SHARPNESS 1 S(A04) SUB CONTRAST 109 S(A05) YC DELAY(H) 15 S(A06) YC DELAY(L) 192 S(A07) VERTICAL PEAKING GAIN 1 S(A08) COMB FILTER 103 S(A09) SUB COLOR(H) 7 S(A10) SUB COLOR(L) 5 S(A11) SUB TINT(H) 0 S(A12) SUB TINT(L) 0 SB:VIDEO-PAL S(B01) LPF 0 S(B02) SUB BRIGHT 16 S(B03) SHARPNESS 1 S(B04) SUB CONTRAST 110 S(B05) YC DELAY(H) 15 S(B06) YC DELAY(L) 128 S(B07) VERTICAL PEAKING GAIN 1 S(B08) COMB FILTER 231 S(B09) SUB COLOR(H) 7 S(B10) SUB COLOR(L) 5 S(B11) SUB TINT(H) 0 S(B12) SUB TINT(L) 0 SC:VIDEO-SECAM S(C01) LPF 0 S(C02) SUB BRIGHT 16 S(C03) SHARPNESS 1 S(C04) SUB CONTRAST 174 S(C05) YC DELAY(H) 15 S(C06) YC DELAY(L) 128 S(C07) VERTICAL PEAKING GAIN 1 S(C08) COMB FILTER 231 S(C09) SUB COLOR(H) 7 S(C10) SUB COLOR(L) 5 S(C11) SUB TINT(H) 0 S(C12) SUB TINT(L) 0 SD:VIDEO-NTSC4.43 S(D01) LPF 0 S(D02) SUB BRIGHT 16 S(D03) SHARPNESS 1 S(D04) SUB CONTRAST 173 S(D05) YC DELAY(H) 15 S(D06) YC DELAY(L) 192 S(D07) VERTICAL PEAKING GAIN 1 S(D08) COMB FILTER 231 S(D09) SUB COLOR(H) 7 S(D10) SUB COLOR(L) 5 S(D11) SUB TINT(H) 0 S(D12) SUB TINT(L) 0
Setting
value
Setting No. Setting item
SE:VIDEO-PALM S(E01) LPF 0 S(E02) SUB BRIGHT 16 S(E03) SHARPNESS 1 S(E04) SUB CONTRAST 174 S(E05) YC DELAY(H) 15 S(E06) YC DELAY(L) 128 S(E07) VERTICAL PEAKING GAIN 1 S(E08) COMB FILTER 231 S(E09) SUB COLOR(H) 7 S(E10) SUB COLOR(L) 5 S(E11) SUB TINT(H) 0 S(E12) SUB TINT(L) 0 SF:VIDEO-PALN S(F01) LPF 0 S(F02) SUB BRIGHT 16 S(F03) SHARPNESS 1 S(F04) SUB CONTRAST 174 S(F05) YC DELAY(H) 15 S(F06) YC DELAY(L) 128 S(F07) VERTICAL PEAKING GAIN 1 S(F08) COMB FILTER 231 S(F09) SUB COLOR(H) 7 S(F10) SUB COLOR(L) 5 S(F11) SUB TINT(H) 0 S(F12) SUB TINT(L) 0 SG:VIDEO-PAL-60 S(G01) LPF 0 S(G02) SUB BRIGHT 16 S(G03) SHARPNESS 1 S(G04) SUB CONTRAST 174 S(G05) YC DELAY(H) 15 S(G06) YC DELAY(L) 128 S(G07) VERTICAL PEAKING GAIN 1 S(G08) COMB FILTER 231 S(G09) SUB COLOR(H) 7 S(G10) SUB COLOR(L) 5 S(G11) SUB TINT(H) 0 S(G12) SUB TINT(L) 0 SH:Y/C-NTSC S(H01) LPF 0 S(H02) SUB BRIGHT 16 S(H03) SHARPNESS 1 S(H04) SUB CONTRAST 108 S(H05) YC DELAY(H) 15 S(H06) YC DELAY(L) 192 S(H07) VERTICAL PEAKING GAIN 1 S(H08) COMB FILTER 231 S(H09) SUB COLOR(H) 7 S(H10) SUB COLOR(L) 5 S(H11) SUB TINT(H) 0 S(H12) SUB TINT(L) 0
Setting
value
(No.YA067)1-71
Page 72
Setting No. Setting item
SI:Y/C-PAL S(I01) LPF 0 S(I02) SUB BRIGHT 16 S(I03) SHARPNESS 1 S(I04) SUB CONTRAST 110 S(I05) YC DELAY(H) 15 S(I06) YC DELAY(L) 128 S(I07) VERTICAL PEAKING GAIN 1 S(I08) COMB FILTER 231 S(I09) SUB COLOR(H) 7 S(I10) SUB COLOR(L) 5 S(I11) SUB TINT(H) 0 S(I12) SUB TINT(L) 0 SJ:Y/C-SECAM S(J01) LPF 0 S(J02) SUB BRIGHT 16 S(J03) SHARPNESS 1 S(J04) SUB CONTRAST 174 S(J05) YC DELAY(H) 15 S(J06) YC DELAY(L) 128 S(J07) VERTICAL PEAKING GAIN 1 S(J08) COMB FILTER 231 S(J09) SUB COLOR(H) 7 S(J10) SUB COLOR(L) 5 S(J11) SUB TINT(H) 0 S(J12) SUB TINT(L) 0 SK:Y/C-NTSC4.43 S(K01) LPF 0 S(K02) SUB BRIGHT 16 S(K03) SHARPNESS 1 S(K04) SUB CONTRAST 173 S(K05) YC DELAY(H) 15 S(K06) YC DELAY(L) 192 S(K07) VERTICAL PEAKING GAIN 1 S(K08) COMB FILTER 231 S(K09) SUB COLOR(H) 7 S(K10) SUB COLOR(L) 5 S(K11) SUB TINT(H) 0 S(K12) SUB TINT(L) 0 SL:Y/C-PALM S(L01) LPF 0 S(L02) SUB BRIGHT 16 S(L03) SHARPNESS 1 S(L04) SUB CONTRAST 174 S(L05) YC DELAY(H) 15 S(L06) YC DELAY(L) 128 S(L07) VERTICAL PEAKING GAIN 1 S(L08) COMB FILTER 231 S(L09) SUB COLOR(H) 7 S(L10) SUB COLOR(L) 5 S(L11) SUB TINT(H) 0 S(L12) SUB TINT(L) 0
Setting
value
Setting No. Setting item
SM:Y/C-PALN S(M01) LPF 0 S(M02) SUB BRIGHT 16 S(M03) SHARPNESS 1 S(M04) SUB CONTRAST 174 S(M05) YC DELAY(H) 15 S(M06) YC DELAY(L) 128 S(M07) VERTICAL PEAKING GAIN 1 S(M08) COMB FILTER 231 S(M09) SUB COLOR(H) 7 S(M10) SUB COLOR(L) 5 S(M11) SUB TINT(H) 0 S(M12) SUB TINT(L) 0 SN:Y/C-PAL60 S(N01) LPF 0 S(N02) SUB BRIGHT 16 S(N03) SHARPNESS 1 S(N04) SUB CONTRAST 174 S(N05) YC DELAY(H) 15 S(N06) YC DELAY(L) 128 S(N07) VERTICAL PEAKING GAIN 1 S(N08) COMB FILTER 231 S(N09) SUB COLOR(H) 7 S(N10) SUB COLOR(L) 5 S(N11) SUB TINT(H) 0 S(N12) SUB TINT(L) 0 SO:COMPO.480i/576i S(O01) LPF 0 S(O02) SUB BRIGHT 16 S(O03) SHARPNESS 1 S(O04) SUB CONTRAST 109
Setting
value
1-72 (No.YA067)
Page 73
DEVICE INITIAL VALUE
Setting No. Setting item
IA:VPC3230D-QA-B3 I(A01) SYNC PIN CONTROL 14 I(A02) 0 I(A03) SYNC GENERATOR CONTROL 0 I(A04) 0 I(A05) OUTPUT STRENGTH 0 I(A06) 0 I(A07) V-SYNC DELAY CONTROL 0 I(A08) 27 I(A09) 656 OUTPUT INTERFACE 0 I(A10) 32 I(A11) LINE LENGTH 3 I(A12) 89 I(A13) HC START 0 I(A14) 50 I(A15) HC STOP 3 I(A16) 32 I(A17) AVO START 16 I(A18) 105 I(A19) AVO STOP 3 I(A20) 56 I(A21) NEWLINE 0 I(A22) 104 I(A23) VPC MODE 0 I(A24) 0 I(A25) PIP MODE 0 I(A26) 0 I(A27) PIP OPERATION 0 I(A28) 0 I(A29) BACKGROUND COLOR 0 I(A30) 0 I(A31) FRAME COLOR 1 0 I(A32) 0 I(A33) FRAME COLOR 2 0 I(A34) 0 I(A35) LINE OFFSET 0 I(A36) 0 I(A37) PIXEL OFFSET 0 I(A38) 0 I(A39) VERTICAL START 0 I(A40) 0 I(A41) HORIZONTAL START 0 I(A42) 0 I(A43) NUMBER OF LINES 0 I(A44) 0 I(A45) NUMBER OF LINES 0 I(A46) 0 I(A47) NUMBER OF PIXEL PER LINE 0 I(A48) 0 I(A49) SATURATION OF THE RGB/YC r C b 8 I(A50) 97 I(A51) TINT CONTROL OF THE RGB/YUV 0 I(A52) 0
Setting
value
Setting No. Setting item
I(A53) BRIGHTNESS OF THE RGB/YUV 27 I(A54) 68 I(A55) SOFTMIXER CONTROL 0 I(A56) 240 I(A57) SOFTMIXER CONTROL 0 I(A58) 224 I(A59) ADC RANGE 0 I(A60) 196 I(A61) Standard select 0 I(A62) 33 I(A63) Enable automatic standard I(A64) 127 I(A65) Input select 4 I(A66) 70 I(A67) picture start position 0 I(A68) 0 I(A69) luma/chroma delay adjust 0 I(A70) 0 I(A71) helper delay register 0 I(A72) 0 I(A73) VGA mode select 0 I(A74) 0 I(A75) comb filter control register 0 I(A76) 0 I(A77) comb filter test register 0 I(A78) 0 I(A79) Saturation control 8 I(A80) 22 I(A81) ACC PAL+ Helper gain adjust 0 I(A82) 0 I(A83) ACC multiplier value for PAL+ I(A84) 0 I(A85) amplitude killer level 0 I(A86) 15 I(A87) amplitude killer hysteresis 0 I(A88) 5 I(A89) automatic helper disable for I(A90) 0 I(A91) NTSC tint angle 0 I(A92) 0 I(A93) crystal oscillator center frequency I(A94) 0 I(A95) crystal oscillator line-locked mode, I(A96) 0 I(A97) crystal oscillator line-locked mode, I(A98) 144 I(A99) general purpose control bits 0 I(A100) 32 I(A101) scaler mode register 0 I(A102) 0 I(A103) pip control register 0 I(A104) 0 I(A105) active video length for 1H-FIFO 2 I(A106) 208
recognition
Helper Signal
nonstandard signals
adjust
lock command
autolock feature
Setting
value
0
0
0
0
0
1
(No.YA067)1-73
Page 74
Setting No. Setting item
I(A107) scaler1 coefficient 6 I(A108) 0 I(A109) scaler2 coefficient 4 I(A110) 0 I(A111) scaler1/2 nonlinear scaling coefficient 0 I(A112) 0 I(A113) scaler1 window controls 0 I(A114) 0 I(A115) scaler1 window controls 0 I(A116) 0 I(A117) scaler1 window controls 0 I(A118) 0 I(A119) scaler1 window controls 0 I(A120) 0 I(A121) scaler1 window controls 0 I(A122) 0 I(A123) scaler2 window controls 0 I(A124) 0 I(A125) scaler2 window controls 0 I(A126) 0 I(A127) scaler2 window controls 0 I(A128) 0 I(A129) scaler2 window controls 0 I(A130) 0 I(A131) scaler2 window controls 0 I(A132) 0 I(A133) brightness register 0 I(A134) 16 I(A135) contrast register 0 I(A136) 48 I(A137) vertical freeze start 15 I(A138) 246 I(A139) vertical freeze stop 0 I(A140) 4 I(A141) 20 bit llc clock center frequency 0 I(A142) 42 I(A143) 20 bit llc clock center frequency 10 I(A144) 171 I(A145) pll frequency limiter 0 I(A146) 54 I(A147) llc clock generator control word 0 I(A148) 5 IB:CXA3516R I(B01) VCODIV1 n, m(L) 24 I(B02) VCODIV2 m(H) 35 I(B03) DELAY 27 I(B04) Charge Punp 18 I(B05) POLARITY 46 I(B06) SYNC 29 I(B07) TTLOUT ENABLE 127 I(B08) MAIN CONTRAST 78 I(B09) SUB CONTRAST G(Y) 128 I(B10) SUB CONTRAST B(Cb) 128 I(B11) SUB CONTRAST R(Cr) 128 I(B12) SUB BRIGHTNESS G(Y) 128
Setting
value
Setting No. Setting item
I(B13) SUB BRIGHTNESS B 128 I(B14) SUB BRIGHTNESS R 128 I(B15) Cb OFFSET 32 I(B16) Cr OFFSET 32 I(B17) AMP MODE 4 I(B18) SYNC SEP 0 I(B19) OUTPUT MODE 0 I(B20) POWER SAVE 48 IC:TA1318N I(C01) Hfreq,HD1/VD1sw,HD2/VD2sw,
SepaLVL
I(C02) DAC1,DAC2,DAC3,test,HD1inv,
HD2inv
I(C03) Vfreq,CLPphase,FREQ DET SW,
INPUTsw I(C04) HDphase,VD1inv,VD2inv 129 ID:REMBRANDT-1A I(D001) OUTPUT_CONTROL 66 I(D002) CONFIG 8 I(D003) ADDR_CLEAR_0 63 I(D004) ADDR_CLEAR_1 255 I(D005) LOAD_SHADOW 0 I(D006) IRQ_SOURCE 0 I(D007) IRQ_MASK 0 I(D008) IRQ_CLEAR 1 I(D009) FLAGS 0 I(D010) FLAGS_CLEAR 1 I(D011) GP_OUTPUT 0 I(D012) STATUS1 0 I(D013) STATUS2 0 I(D014) MPLL_MDIV_L 2 I(D015) MPLL_MDIV_H 0 I(D016) MPLL_NDIV 0 I(D017) PPLL_MDIV_L 3 I(D018) PPLL_MDIV_H 0 I(D019) PPLL_NDIV 0 I(D020) OPLL_MDIV_L 36 I(D021) OPLL_MDIV_H 0 I(D022) OPLL_NDIV 14 I(D023) NL_CONTROL 5 I(D024) NL_SWITCH 0 I(D025) NL_X 0 I(D026) NL_Y 0 I(D027) VIDEO_CONFIG 8 I(D028) VIDEO_SC 8 I(D029) VIN_POLARITY 0 I(D030) VIN_CONTROL 0 I(D031) VIN_ACTIVE_PIXELS_L 0 I(D032) VIN_ACTIVE_LINES_L 0 I(D033) VIN_FLAGGED_LINE 0 I(D034) VIN_REGS_MSBITS 0 I(D035) VIN_FILTER_GRP / C0 0 I(D036) VIN_FILTER_GRP / C1 0 I(D037) VIN_FILTER_GRP / C2 0 I(D038) VIN_FILTER_GRP / C3 0
Setting
value
61
167
192
1-74 (No.YA067)
Page 75
Setting No. Setting item
I(D039) VIN_FILTER_GRP / C4 64 I(D040) VIN_FILTER_GRP / C5 0 I(D041) VIN_FILTER_GRP / C6 0 I(D042) VIN_FILTER_GRP / C7 0 I(D043) VIN_FILTER_GRP / C8 0 I(D044) VOUT_FILTER_GRP / C0 253 I(D045) VOUT_FILTER_GRP / C1 250 I(D046) VOUT_FILTER_GRP / C2 253 I(D047) VOUT_FILTER_GRP / C3 250 I(D048) VOUT_FILTER_GRP / C4 100 I(D049) VOUT_FILTER_GRP / C5 250 I(D050) VOUT_FILTER_GRP / C6 253 I(D051) VOUT_FILTER_GRP / C7 250 I(D052) VOUT_FILTER_GRP / C8 253 I(D053) N/A 0 I(D054) N/A 0 I(D055) VDSCALER_TOUTX_L 208 I(D056) VDSCALER_TOUTX_H 2 I(D057) VDSCALER_CONTROL 0 I(D058) VDSCALER_DELTAX_L 0 I(D059) VDSCALER_DELTAX_H 8 I(D060) VDSCALER_DELTAY_L 0 I(D061) VDSCALER_DELTAY_H 8 I(D062) VDSCALER_Y0 0 I(D063) VDSCALER_X0 0 I(D064) VDSCALER_TOUTY_L 224 I(D065) VDSCALER_TOUTY_H 1 I(D066) VUSCALER_CONTROL 0 I(D067) VUSCALER_DELTAX_L 192 I(D068) VUSCALER_DELTAX_H 6 I(D069) VUSCALER_DELTAY_L 0 I(D070) VUSCALER_DELTAY_H 8 I(D071) VUSCALER_Y0 0 I(D072) VUSCALER_X0 0 I(D073) DI_CONTROL 4 I(D074) DI_C0 31 I(D075) DI_C1 7 I(D076) DI_C2 127 I(D077) DI_C3 255 I(D078) DI_C4 31 I(D079) DATA_CONFIG 0 I(D080) DATA_SC 8 I(D081) DIN_POLARITY_0 56 I(D082) DIN_POLARITY_1 0 I(D083) DIN_CONTROL_0 3 I(D084) DIN_CONTROL_1 64 I(D085) DIN_CONTROL_2 2 I(D086) DPLL_DIV_L 0 I(D087) DPLL_DIV_H 0 I(D088) DIN_THRESHOLD 8 I(D089) CLAMP_START 1 I(D090) CLAMP_WIDTH 16 I(D091) DIN_LINE_TRIG 1 I(D092) DIN_PIXEL_TRIG 1 I(D093) ACTIVE_LINE_START_L 38
Setting
value
Setting No. Setting item
I(D094) ACTIVE_LINE_START_H 0 I(D095) ACTIVE_LINES_L 224 I(D096) ACTIVE_LINES_H 1 I(D097) ACTIVE_PIXEL_START_L 132 I(D098) ACTIVE_PIXEL_START_H 0 I(D099) ACTIVE_PIXELS_L 128 I(D100) ACTIVE_PIXELS_H 2 I(D101) DIN_FLAGGED_LINE_L 0 I(D102) DIN_FLAGGED_LINE_H 0 I(D103) DIN_CONTROL_3 6 I(D104) N/A 0 I(D105) N/A 0 I(D106) N/A 0 I(D107) DIN_FILTER_GRP / C0 0 I(D108) DIN_FILTER_GRP / C1 0 I(D109) DIN_FILTER_GRP / C2 0 I(D110) DIN_FILTER_GRP / C3 0 I(D111) DIN_FILTER_GRP / C4 127 I(D112) DIN_FILTER_GRP / C5 0 I(D113) DIN_FILTER_GRP / C6 0 I(D114) DIN_FILTER_GRP / C7 0 I(D115) DIN_FILTER_GRP / C8 0 I(D116) DDSCALER_TOUTX_L 128 I(D117) DDSCALER_TOUTX_H 2 I(D118) DDSCALER_CONTROL 0 I(D119) DDSCALER_DELTAX_L 0 I(D120) DDSCALER_DELTAX_H 8 I(D121) DDSCALER_DELTAY_L 0 I(D122) DDSCALER_DELTAY_H 8 I(D123) N/A 0 I(D124) N/A 0 I(D125) DDSCALER_TOUTY_L 224 I(D126) DDSCALER_TOUTY_H 1 I(D127) DUSCALER_CONTROL 0 I(D128) DUSCALER_DELTAX_L 191 I(D129) DUSCALER_DELTAX_H 3 I(D130) DUSCALER_DELTAY_L 255 I(D131) DUSCALER_DELTAY_H 4 I(D132) DUSCALER_X0 1 I(D133) DUSCALER_Y0 1 I(D134) VIDEO_WINDOW_GRP / Y_POS_L 1 I(D135) VIDEO_WINDOW_GRP / Y_POS_H 0 I(D136) VIDEO_WINDOW_GRP / Y_SIZE_L 224 I(D137) VIDEO_WINDOW_GRP / Y_SIZE_H 1 I(D138) VIDEO_WINDOW_GRP / X_POS_L 1 I(D139) VIDEO_WINDOW_GRP / X_POS_H 0 I(D140) VIDEO_WINDOW_GRP / X_SIZE_L 85 I(D141) VIDEO_WINDOW_GRP / X_SIZE_H 3 I(D142) DATA_WINDOW_GRP / Y_POS_L 1 I(D143) DATA_WINDOW_GRP / Y_POS_H 0 I(D144) DATA_WINDOW_GRP / Y_SIZE_L 0 I(D145) DATA_WINDOW_GRP / Y_SIZE_H 3 I(D146) DATA_WINDOW_GRP / X_POS_L 1 I(D147) DATA_WINDOW_GRP / X_POS_H 0 I(D148) DATA_WINDOW_GRP / X_SIZE_L 86
Setting
value
(No.YA067)1-75
Page 76
Setting No. Setting item
I(D149) DATA_WINDOW_GRP / X_SIZE_H 5 I(D150) OSDA_WINDOW_GRP / Y_POS_L 0 I(D151) OSDA_WINDOW_GRP / Y_POS_H 0 I(D152) OSDA_WINDOW_GRP / Y_SIZE_L 0 I(D153) OSDA_WINDOW_GRP / Y_SIZE_H 0 I(D154) OSDA_WINDOW_GRP / X_POS_L 0 I(D155) OSDA_WINDOW_GRP / X_POS_H 0 I(D156) OSDA_WINDOW_GRP / X_SIZE_L 0 I(D157) OSDA_WINDOW_GRP / X_SIZE_H 0 I(D158) OSDB_WINDOW_GRP / Y_POS_L 0 I(D159) OSDB_WINDOW_GRP / Y_POS_H 0 I(D160) OSDB_WINDOW_GRP / Y_SIZE_L 0 I(D161) OSDB_WINDOW_GRP / Y_SIZE_H 0 I(D162) OSDB_WINDOW_GRP / X_POS_L 0 I(D163) OSDB_WINDOW_GRP / X_POS_H 0 I(D164) OSDB_WINDOW_GRP / X_SIZE_L 0 I(D165) OSDB_WINDOW_GRP / X_SIZE_H 0 I(D166) LUT_Y 0 I(D167) LUT_U 0 I(D168) LUT_V 0 I(D169) LUT_R_L 0 I(D170) LUT_R_H 0 I(D171) LUT_G_L 0 I(D172) LUT_G_H 0 I(D173) LUT_B_L 0 I(D174) LUT_B_H 0 I(D175) PALETTE_R 0 I(D176) PALETTE_G 0 I(D177) PALETTE_B 0 I(D178) VIDEO_CSC_BIAS 0 I(D179) VIDEO_CSC_GRP / C(0)_L 0 I(D180) VIDEO_CSC_GRP / C(0)_H 4 I(D181) VIDEO_CSC_GRP / C(1)_L 0 I(D182) VIDEO_CSC_GRP / C(1)_H 0 I(D183) VIDEO_CSC_GRP / C(2)_L 114 I(D184) VIDEO_CSC_GRP / C(2)_H 1 I(D185) VIDEO_CSC_GRP / C(3)_L 0 I(D186) VIDEO_CSC_GRP / C(3)_H 4 I(D187) VIDEO_CSC_GRP / C(4)_L 165 I(D188) VIDEO_CSC_GRP / C(4)_H 255 I(D189) VIDEO_CSC_GRP / C(5)_L 67 I(D190) VIDEO_CSC_GRP / C(5)_H 255 I(D191) VIDEO_CSC_GRP / C(6)_L 0 I(D192) VIDEO_CSC_GRP / C(6)_H 4 I(D193) VIDEO_CSC_GRP / C(7)_L 212 I(D194) VIDEO_CSC_GRP / C(7)_H 1 I(D195) VIDEO_CSC_GRP / C(8)_L 0 I(D196) VIDEO_CSC_GRP / C(8)_H 0 I(D197) DATA_CSC_BIAS 0 I(D198) DATA_CSC_GRP / C(0)_L 0 I(D199) DATA_CSC_GRP / C(0)_H 4 I(D200) DATA_CSC_GRP / C(1)_L 0 I(D201) DATA_CSC_GRP / C(1)_H 0 I(D202) DATA_CSC_GRP / C(2)_L 191 I(D203) DATA_CSC_GRP / C(2)_H 1
Setting
value
Setting No. Setting item
I(D204) DATA_CSC_GRP / C(3)_L 0 I(D205) DATA_CSC_GRP / C(3)_H 4 I(D206) DATA_CSC_GRP / C(4)_L 203 I(D207) DATA_CSC_GRP / C(4)_H 255 I(D208) DATA_CSC_GRP / C(5)_L 123 I(D209) DATA_CSC_GRP / C(5)_H 255 I(D210) DATA_CSC_GRP / C(6)_L 0 I(D211) DATA_CSC_GRP / C(6)_H 4 I(D212) DATA_CSC_GRP / C(7)_L 15 I(D213) DATA_CSC_GRP / C(7)_H 2 I(D214) DATA_CSC_GRP / C(8)_L 0 I(D215) DATA_CSC_GRP / C(8)_H 0 I(D216) OUT_CONFIG 12 I(D217) BACKGROUND_GRP / BLUE 0 I(D218) BACKGROUND_GRP / GREEN 0 I(D219) BACKGROUND_GRP / RED 0 I(D220) OSDA_CONTROL 0 I(D221) OSDB_CONTROL 0 I(D222) KEYSTONE_CONTROL 0 I(D223) KEYSTONE_LINES 255 I(D224) DITHER_CONTROL 42 I(D225) DITHER_C0 60 I(D226) DITHER_C1 56 I(D227) DISPLAY_CONTROL_0 16 I(D228) DISPLAY_CONTROL_1 0 I(D229) DISPLAY_CONTROL_2 3 I(D230) D/F_GRP / VSYNC_CYCLE_L 32 I(D231) D/F_GRP / VSYNC_CYCLE_H 3 I(D232) D/F_GRP / HSYNC_CYCLE_L 220 I(D233) D/F_GRP / HSYNC_CYCLE_H 5 I(D234) D/F_GRP / VSYNC_WIDTH 3 I(D235) D/F_GRP / VSYNC_OFFSET_H 0 I(D236) D/F_GRP / HSYNC_WIDTH_L 110 I(D237) D/F_GRP / HSYNC_WIDTH_H 0 I(D238) D/F_GRP / ACTIVE_LINE_START_L 30 I(D239) D/F_GRP / ACTIVE_LINE_START_H 0 I(D240) D/F_GRP / ACTIVE_LINES_L 4 I(D241) D/F_GRP / ACTIVE_LINES_H 3 I(D242) D/F_GRP /
ACTIVE_PIXEL_START_L I(D243) D/F_GRP /
ACTIVE_PIXEL_START_H I(D244) D/F_GRP / ACTIVE_PIXELS_L 94 I(D245) D/F_GRP / ACTIVE_PIXELS_H 5 I(D246) DISPLAY_HV_DELAY_0 1 I(D247) DISPLAY_HV_DELAY_1 1 I(D248) DISPLAY_POLARITY 0 I(D249) CONTROL_3D 0 I(D250) X0_3D 0 I(D251) SECT_START_GRP / VIDEO0_L 0 I(D252) SECT_START_GRP / VIDEO0_H 0 I(D253) SECT_START_GRP / VIDEO1_L 0 I(D254) SECT_START_GRP / VIDEO1_H 0 I(D255) SECT_START_GRP / VIDEO2_L 0 I(D256) SECT_START_GRP / VIDEO2_H 0
Setting
value
58
0
1-76 (No.YA067)
Page 77
Setting No. Setting item
I(D257) SECT_START_GRP / LDATA0_L 0 I(D258) SECT_START_GRP / LDATA0_H 0 I(D259) SECT_START_GRP / RDATA0_L 0 I(D260) SECT_START_GRP / RDATA0_H 2 I(D261) SECT_START_GRP / LDATA1_L 0 I(D262) SECT_START_GRP / LDATA1_H 4 I(D263) SECT_START_GRP / RDATA1_L 0 I(D264) SECT_START_GRP / RDATA1_H 6 I(D265) SECT_START_GRP / OSD0_L 0 I(D266) SECT_START_GRP / OSD0_H 0 I(D267) SECT_START_GRP / OSD1_L 0 I(D268) SECT_START_GRP / OSD1_H 0 I(D269) SECT_START_GRP / OSD2_L 0 I(D270) SECT_START_GRP / OSD2_H 0 I(D271) SECT_START_GRP / OSD3_L 0 I(D272) SECT_START_GRP / OSD3_H 0 I(D273) S/S_GRP / IDATA_OFFSET_L 0 I(D274) S/S_GRP / IDATA_OFFSET_H 0 I(D275) LINE_LENGTH_GRP / VIDEO_L 0 I(D276) LINE_LENGTH_GRP / VIDEO_H 0 I(D277) LINE_LENGTH_GRP / DATA_L 210 I(D278) LINE_LENGTH_GRP / DATA_H 0 I(D279) LINE_LENGTH_GRP / IDATA_L 0 I(D280) LINE_LENGTH_GRP / IDATA_H 0 I(D281) LINE_LENGTH_GRP / OSD0_L 0 I(D282) LINE_LENGTH_GRP / OSD0_H 0 I(D283) LINE_LENGTH_GRP / OSD1_L 0 I(D284) LINE_LENGTH_GRP / OSD1_H 0 I(D285) LINE_LENGTH_GRP / OSD2_L 0 I(D286) LINE_LENGTH_GRP / OSD2_H 0 I(D287) LINE_LENGTH_GRP / OSD3_L 0 I(D288) LINE_LENGTH_GRP / OSD3_H 0 I(D289) WIN_LINE_OFFSET_GRP /
VIDEO_L
I(D290) WIN_LINE_OFFSET_GRP /
VIDEO_H I(D291) WIN_LINE_OFFSET_GRP / DATA_L 0 I(D292) WIN_LINE_OFFSET_GRP / DATA_H 0 I(D293) WIN_LINE_OFFSET_GRP / OSDA_L 0 I(D294) WIN_LINE_OFFSET_GRP /
OSDA_H I(D295) WIN_LINE_OFFSET_GRP / OSDB_L 0 I(D296) WIN_LINE_OFFSET_GRP /
OSDB_H I(D297) WIN_DELAY_GRP / VIDEO_L 0 I(D298) WIN_DELAY_GRP / VIDEO_H 0 I(D299) WIN_DELAY_GRP / DATA_L 0 I(D300) WIN_DELAY_GRP / DATA_H 0 I(D301) WIN_DELAY_GRP / OSDA_L 0 I(D302) WIN_DELAY_GRP / OSDA_H 0 I(D303) WIN_DELAY_GRP / OSDB_L 0 I(D304) WIN_DELAY_GRP / OSDB_H 0 I(D305) WIN_LENGTH_GRP / VIDEO_L 208 I(D306) WIN_LENGTH_GRP / VIDEO_H 2 I(D307) WIN_LENGTH_GRP / DATA_L 0
Setting
value
Setting No. Setting item
I(D308) WIN_LENGTH_GRP / DATA_H 0 I(D309) WIN_LENGTH_GRP / OSDA_L 0 I(D310) WIN_LENGTH_GRP / OSDA_H 0 I(D311) WIN_LENGTH_GRP / OSDB_L 0 I(D312) WIN_LENGTH_GRP / OSDB_H 0 I(D313) SC_THRESHOLD_GRP / VIDEO_IN 64 I(D314) SC_THRESHOLD_GRP /
VIDEO_OUT I(D315) SC_THRESHOLD_GRP / DATA_IN 32 I(D316) SC_THRESHOLD_GRP /
DATA_OUT I(D317) OSD_IN_ADDR_L 0 I(D318) OSD_IN_ADDR_R 0 I(D319) OSD_IN_BLOCK_LENGTH 0 I(D320) OSD_SECTIONS 0 I(D321) OSD_IN_DATA 0 I(D322) OSD_IN_CONTROL 0 I(D323) SDRAM_WINDOW_CONTROL 0 I(D324) SDRAM_INIT 0 I(D325) MSR_AOI_GRP / LINE_START_L 0 I(D326) MSR_AOI_GRP / LINE_START_H 0 I(D327) MSR_AOI_GRP / LINE_END_L 0 I(D328) MSR_AOI_GRP / LINE_END_H 0 I(D329) MSR_AOI_GRP / PIXEL_START_L 0 I(D330) MSR_AOI_GRP / PIXEL_START_H 0 I(D331) MSR_AOI_GRP / PIXEL_END_L 0 I(D332) MSR_AOI_GRP / PIXEL_END_H 0 I(D333) MSR_CONTROL 72 I(D334) MSR_ENABLE 1 I(D335) MSR_COMMANDS 0 I(D336) MSR_STATUS 0 I(D337) MSR_HV_PARAMETERS_GRP /
0
I(D338) MSR_HV_PARAMETERS_GRP /
0
I(D339) MSR_HV_PARAMETERS_GRP /
I(D340) MSR_HV_PARAMETERS_GRP /
I(D341) MSR_HV_PARAMETERS_GRP /
0
I(D342) MSR_HV_PARAMETERS_GRP /
0
I(D343) MSR_HV_PARAMETERS_GRP /
I(D344) MSR_HV_PARAMETERS_GRP /
I(D345) MSR_HV_PARAMETERS_GRP /
I(D346) MSR_HV_PARAMETERS_GRP /
I(D347) MSR_ACTIVE_REGION_GRP /
I(D348) MSR_ACTIVE_REGION_GRP /
I(D349) MSR_ACTIVE_REGION_GRP /
HSYNC_WIDTH_L
HSYNC_WIDTH_H
HSYNC_CYCLE_L
HSYNC_CYCLE_H
VSYNC_WIDTH_L
VSYNC_WIDTH_H
VSYNC_CYCLE_L
VSYNC_CYCLE_H
HV_DELAY_L
HV_DELAY_H
LINE_START_L
LINE_START_H
LINE_END_L
Setting
value
64
32
0
0
0
0
0
0
0
0
0
0
0
0
0
(No.YA067)1-77
Page 78
Setting No. Setting item
I(D350) MSR_ACTIVE_REGION_GRP /
LINE_END_H
I(D351) MSR_ACTIVE_REGION_GRP /
PIXEL_START_L
I(D352) MSR_ACTIVE_REGION_GRP /
PIXEL_START_H
I(D353) MSR_ACTIVE_REGION_GRP /
PIXEL_END_L
I(D354) MSR_ACTIVE_REGION_GRP /
PIXEL_END_H I(D355) MSR_YMIN 0 I(D356) MSR_YMAX 0 IE : PDP I/F I(E01) ERROR DIFFUSION/DITHER/
CONTRARY GAMMA SELECT/reserved I(E02) PANEL SERIAL DATA low-bit 2 I(E03) PANEL SERIAL DATA high-bit 3 I(E04) bit INVERT/reserved/TEST MODE 0 I(E05) WHITE BALANCE OFFSET(G) 0 I(E06) WHITE BALANCE OFFSET(B) 0 I(E07) WHITE BALANCE OFFSET(R) 0 I(E08) WHITE BALANCE ADJUST 0 I(E09) TEST MODE BRIGHT 128 I(E10) BLACK LEVEL ADJUST 10 I(E11) GAIN LEVEL ADJUST 176 I(E12) WHITE BALANCE GAIN ADJUST(G) 255 I(E13) WHITE BALANCE GAIN ADJUST(B) 255 I(E14) WHITE BALANCE GAIN ADJUST(R) 255 I(E15) NOT USED 0 I(E16) NOT USED 0 I(E17) NOT USED 0 I(E18) NOT USED 0 I(E19) NOT USED 0 I(E20) NOT USED 0 IF:JCC5054(DSD) I(F001) ayenhjuni,aslvgain 14 I(F002) aslvhgain 1 I(F003) aslhgain 103 I(F004) aslhpeakfreq,aslvpeakfreq,asledgeco
ntrol I(F005) aslpmbalance 32 I(F006) aslcoringlevel 50 I(F007) asvgain 192 I(F008) asvhgain 64 I(F009) ashgain 35 I(F010) ashpeakfreq,asvpeakfreq,
asedgecontrol I(F011) aspmbalance 128 I(F012) ayenhon,ascoringlevel 1 I(F013) apbenhon,apbenhjuni,apbgain 192 I(F014) apbpeakfreq,apbcoringlevel 34 I(F015) aprenhon,aprenhjuni,aprgain 0 I(F016) aprpeakfreq,aprcoringlevel 37 I(F017) avmgain 42 I(F018) avmhcontrol,avmpeakfreq 0 I(F019) avmcoringlevel 44
Setting
value
136
19
64
Setting No. Setting item
I(F020) avmon,avmlimit 255
0
I(F021) byenhjuni,bslvgain 255
0
I(F022) bslvhgain 255 I(F023) bslhgain 255
0
I(F024) bslhpeakfreq,bslvpeakfreq,
0
I(F025) bslpmbalance 0 I(F026) bslcoringlevel 255
0
I(F027) bsvgain 15 I(F028) bsvhgain 0 I(F029) bshgain 0 I(F030) bshpeakfreq,bsvpeakfreq,
I(F031) bspmbalance 0 I(F032) byenhon,bscoringlevel 0 I(F033) bpbenhon,bpbenhjyuni,bpbgain 0 I(F034) bpbpeakfreq,bpbcoringlevel 3 I(F035) bprenhon,bprenhjyuni,bprgain 32 I(F036) bprpeakfreq,bprcoringlevel 0 I(F037) bvmgain 3 I(F038) bvmhcontrol,bvmpeakfreq 32 I(F039) bvmcoringlevel 191 I(F040) bvmon,bvmlimit 82 I(F041) yunderlimitL 96 I(F042) linedelayL 0 I(F043) odsdbon,odsdaon,yunderlimitH,linede
I(F044) ovmdelay 0 I(F045) odsdbp,odsdap,iblankp,idsdbp,
I(F046) blankodsdb,blankodsda,
I(F047) avstartL 53 I(F048) avwidthL 0 I(F049) avwidthH,avstartH 0 I(F050) ahstartL 0 I(F051) ahwidthL 255 I(F052) ahwidthH,ahstartH 15 I(F053) bvstartL 255 I(F054) bvwidthL 15 I(F055) bvwidthH,bvstartH 0 I(F056) bhstartL 0 I(F057) bhwidthL 14 I(F058) bhwidthH,bhstartH 1 I(F059) blankvstartL 103 I(F060) blankvwidthL 19 I(F061) blankvwidthH,blankvstartH 32 I(F062) blankhstartL 50 I(F063) blankhwidthL 192 I(F064) blankhwidthH,blankhstartH 64 I(F065) vmcenterL 35 I(F066) vhmark,vhalf,vquarter,vdauto,
I(F067) KSETL 128 I(F068) KSETH 1
bsledgecontrol
bsedgecontrol
layH
idsdap,hdp,vdp
blankvm,blankdsd,priorityb,iblank, idsdb,idsda
vmcenterH
Setting
value
15
0
0
0
0
64
1-78 (No.YA067)
Page 79
Setting No. Setting item
I(F069) INIK_L 192 I(F070) INIK_H 34 I(F071) HPOS_RL 0 I(F072) PANO_CNTRH,HPOS_RH 37 I(F073) PANO_CNTRL 42 I(F074) PANO_LIMTL 0 I(F075) PANO_HIL2_POSH,PANO_LIMTH 44 I(F076) PANO_HIL2_POSL 255 I(F077) PANO_HIL1_POSL 255 I(F078) PANO_BAS2_POSH,
PANO_HIL1_POSH I(F079) PANO_BAS2_POSL 255 I(F080) PANO_HIL2_GRDL 15 I(F081) PANO_HIL1_GRDH,
PANO_HIL2_GRDH I(F082) PANO_HIL1_GRDL 255 I(F083) PANO_BAS2_GRDL 15 I(F084) PANO_BAS1_GRDH,
PANO_BAS2_GRDH I(F085) PANO_BAS1_GRDL 0 I(F086) BLK_ADR_STAL 0 I(F087) BLK_ADR_POSH,BLK_ADR_STAH 0 I(F088) BLK_ADR_POSL 0 I(F089) MASK_1_STAL 0 I(F090) MASK_1_ENDH,MASK_1_STAH 3 I(F091) MASK_1_ENDL 32 I(F092) MASK_2_STAL 0 I(F093) MASK_2_ENDH,MASK_2_STAH 3 I(F094) MASK_2_ENDL 32 I(F095) FLT_SEL_A,DATSEL_INT,INIK_msb 191 I(F096) KSET_2ndH,BLK_INIKH,
PSEL,IN_MASK,MIP_OUT I(F097) KSET_2ndL 96 I(F098) LM_SELEN,PANO_SHFT,
PANO_INV I(F099) BLK_ADR_ENDH,LPF 0 I(F100) BLK_ADR_ENDL 0 I(F101) OUTCNST_R 0 I(F102) PXRST_SEL_Y,PARA_SEL 0 I(F103) PXRST_SEL_R,PXRST_SEL_B 53 I(F104) VD_POSL 0 I(F105) VD_WDHH,VD_POSH 0 I(F106) VD_WDHL 0 I(F107) PANO_POS_AL 255 I(F108) BLK_RST_AH,PANO_POS_AH 15 I(F109) PANO_POS_BL 255 I(F110) BLK_RST_BH,PANO_POS_BH 15 I(F111) BLK_RST_AL 0 I(F112) BLK_RST_BL 0 I(F113) yblkoff 0 I(F114) pbblkoff 0 I(F115) prblkoff 0 I(F116) blktopL 0 I(F117) blkbottomL 255 I(F118) viewblkon,blkbottomH,blktopH 48
Setting
value
255
82
Setting No. Setting item
I(F119) blkleftL 0 I(F120) blkrightL 246 I(F121) blkrightH,blkleftH 80 I(F122) yodelay,codelay,pbodelay,prodelay 0 I(F123) hdelay 40 I(F124) usertopL 255 I(F125) userbottomL 0 I(F126) userpol,userbottomH,usertopH 7 I(F127) userleftL 255 I(F128) userrightL 0 I(F129) userrightH,userleftH 15 I(F130) inhlineL 234 I(F131) inhon,inhpol,inhlineH 2
0
I(F132) divlengthL 0 I(F133) divlengthH 0 I(F134) hdotnumL 219 I(F135) vlinenumH,hdotnumH 101
0
I(F136) vlinenumL 113 I(F137) hsyncposL 0 I(F138) valign,fidxauto,vsyncpos,hsyncposH 0 I(F139) vsyncpoL 0 I(F140) hsyncpol,hsyncwidth 51 I(F141) vsyncpol,vsyncwidth 15 I(F142) hdoposL 0 I(F143) vdoposH,hdoposH 0 I(F144) vdoposL 0 I(F145) hdopol,hdowidth 109 I(F146) vdopol,vdowidth 5 I(F147) extvsync,exthsync,extvrst,interace,
fidxpol,harfhauto,divfree,syncthru
I(F148) extvfree,exthfree,interace2,fidxoff,
hdooff,vdooff,hsyncoff,vsyncoff
I(F149) REGFF,I2CEXT,VIEW_THRU,
0
IG:UPD64083GF I(G01) OPERATION MODE, HH DECODE,
I(G02) CLOCK, STANDARD/
I(G03) DYCO, EXTERNAL Y-ADC,
I(G04) ADC INPUT AMPLITUDE
I(G05) DY CORING LEVEL/GAIN 42 I(G06) DC CORING LEVEL/GAIN 36 I(G07) FRAME RECURSIVE NR GAIN,
I(G08) ID-1, CLK8, ST1, ST0 1 I(G09) CORING LEVEL/HYSTERESIS/
I(G10) ADC INPUT BIT-WIDTH 72 I(G11) V APARTURE COMPENSATION
DSD_THRU,HDPC_THRU
SIGNAL OUTPUT
NON-STANDARD, INTER-FRAME/INTER-LINE, KILLER
EXTERNAL MEMORY, EXTERNAL CSync
CLAMPPING WIDTH, H PHASE, C-DELAY
CONVERGENT LEVEL, LIMIT SETTING
SENSITIVITY
GAIN, CONVERGENT POINT
Setting
value
192
0
133
21
0
193
34
34
86
43
(No.YA067)1-79
Page 80
Setting No. Setting item
I(G12) Y PEAKING FILTER's CENTER
FREQ./GAIN
I(G13) LINE-COMB, C-DELAY for NR,
DC SENSITIVITY I(G14) DY SENSITIVITY 37 I(G15) NOT USED 8 I(G16) NOT USED 68 I(G17) YH CORING, WCV-ID DETECT 112 I(G18) TEST BIT for NON-STANDARD
DETECTOR I(G19) PLL, BURST SAMPLING/KILLER 51 I(G20) H/V SYNC. SLICE LEVEL 200 I(G21) BURST GATE POSITION/WIDTH 74 I(G22) ADC CLOCK DELAY, WCV-ID
DETECT I(G23) POWER DOWN, FIELD MEMORY,
HH CARRIER PHASE I(G24) HH DECODE MOTION GAIN,
HH OUTPUT CORING
Setting
value
12
241
236
8
0
8
1-80 (No.YA067)
Page 81
ENHACER BLOCK
Setting No. Setting item
EA:VIDEO E(A01) Y SHOOTLESS/LIMIT RANK 1 E(A02) Y SHOOTLESS/V GAIN 20 E(A03) Y SHOOTLESS/DIAGONAL GAIN 20 E(A04) Y SHOOTLESS/H GAIN 20 E(A05) Y SHOOTLESS/H PEAK FREQ. 1 E(A06) Y SHOOTLESS/V PEAK FREQ. 1 E(A07) Y SHOOTLESS/EDGE CONTROL 12 E(A08) Y SHOOTLESS/POSITIVE and
NEGATIVE GAIN BALANCE E(A09) Y SHOOTLESS/CORING LEVEL 63 E(A10) Y with SHOOT/V GAIN(TYP.) 20 E(A11) Y with SHOOT/
DIAGONAL GAIN(TYP.) E(A12) Y with SHOOT/H GAIN(TYP.) 12 E(A13) Y with SHOOT/H PEAK FREQ. 0 E(A14) Y with SHOOT/V PEAK FREQ. 0 E(A15) Y with SHOOT/EDGE CONTROL 12 E(A16) Y with SHOOT/POSITIVE and
NEGATIVE GAIN BALANCE E(A17) Y ENHANCER/ON 1 E(A18) Y with SHOOT/CORING LEVEL 63 E(A19) Pb ENHANCER/ON 1 E(A20) Pb ENHANCER/LIMIT RANK 1 E(A21) Pb ENHANCER/GAIN 63 E(A22) Pb ENHANCER/PEAK FREQ. 0 E(A23) Pb ENHANCER/CORING LEVEL 63 E(A24) Pr ENHANCER/ON 1 E(A25) Pr ENHANCER/LIMIT RANK 1 E(A26) Pr ENHANCER/GAIN 63 E(A27) Pr ENHANCER/PEAK FREQ. 0 E(A28) Pr ENHANCER/CORING LEVEL 63 E(A29) Y SHOOT ENHANCER/V GAIN(MIN.) 96 E(A30) Y SHOOT ENHANCER/
V GAIN(MAX.) E(A31) Y SHOOT ENHANCER/
DIAGONAL GAIN(MIN.) E(A32) Y SHOOT ENHANCER/
DIAGONAL GAIN(MAX.) E(A33) Y SHOOT ENHANCER/H GAIN(MIN.) 96 E(A34) Y SHOOT ENHANCER/
H GAIN(MAX.) E(A35) NOT USED 0 E(A36) NOT USED 0 E(A37) NOT USED 0 E(A38) NOT USED 0 E(A39) NOT USED 0 E(A40) NOT USED 0 E(A41) FILTER COEFFICIENT C0 128 E(A42) FILTER COEFFICIENT C1 128 E(A43) FILTER COEFFICIENT C2 128 E(A44) FILTER COEFFICIENT C3 128 E(A45) FILTER COEFFICIENT C4 192 E(A46) FILTER COEFFICIENT C5 128 E(A47) FILTER COEFFICIENT C6 128
Setting
value
144
144
144
96
Setting No. Setting item
E(A48) FILTER COEFFICIENT C7 128 E(A49) FILTER COEFFICIENT C8 128 E(A50) NOT USED 0 EB:COMPO.SD E(B01) Y SHOOTLESS/LIMIT RANK 1 E(B02) Y SHOOTLESS/V GAIN 16 E(B03) Y SHOOTLESS/DIAGONAL GAIN 32 E(B04) Y SHOOTLESS/H GAIN 16 E(B05) Y SHOOTLESS/H PEAK FREQ. 0
0
E(B06) Y SHOOTLESS/V PEAK FREQ. 0 E(B07) Y SHOOTLESS/EDGE CONTROL 12 E(B08) Y SHOOTLESS/POSITIVE and
0
E(B09) Y SHOOTLESS/CORING LEVEL 63 E(B10) Y with SHOOT/V GAIN(TYP.) 24 E(B11) Y with SHOOT/
E(B12) Y with SHOOT/H GAIN(TYP.) 24 E(B13) Y with SHOOT/H PEAK FREQ. 0
0
E(B14) Y with SHOOT/V PEAK FREQ. 0 E(B15) Y with SHOOT/EDGE CONTROL 12 E(B16) Y with SHOOT/POSITIVE and
E(B17) Y ENHANCER/ON 1 E(B18) Y with SHOOT/CORING LEVEL 63 E(B19) Pb ENHANCER/ON 1 E(B20) Pb ENHANCER/LIMIT RANK 1 E(B21) Pb ENHANCER/GAIN 24 E(B22) Pb ENHANCER/PEAK FREQ. 0 E(B23) Pb ENHANCER/CORING LEVEL 63 E(B24) Pr ENHANCER/ON 1 E(B25) Pr ENHANCER/LIMIT RANK 1 E(B26) Pr ENHANCER/GAIN 24 E(B27) Pr ENHANCER/PEAK FREQ. 0 E(B28) Pr ENHANCER/CORING LEVEL 63 E(B29) Y SHOOT ENHANCER/V GAIN(MIN.) 96 E(B30) Y SHOOT ENHANCER/
E(B31) Y SHOOT ENHANCER/
E(B32) Y SHOOT ENHANCER/
E(B33) Y SHOOT ENHANCER/H GAIN(MIN.) 96 E(B34) Y SHOOT ENHANCER/
E(B35) NOT USED 0 E(B36) NOT USED 0 E(B37) NOT USED 0 E(B38) NOT USED 0 E(B39) NOT USED 0 E(B40) NOT USED 0 E(B41) FILTER COEFFICIENT C0 128 E(B42) FILTER COEFFICIENT C1 128 E(B43) FILTER COEFFICIENT C2 128 E(B44) FILTER COEFFICIENT C3 128
NEGATIVE GAIN BALANCE
DIAGONAL GAIN(TYP.)
NEGATIVE GAIN BALANCE
V GAIN(MAX.)
DIAGONAL GAIN(MIN.)
DIAGONAL GAIN(MAX.)
H GAIN(MAX.)
Setting
value
0
24
0
160
96
160
160
(No.YA067)1-81
Page 82
Setting No. Setting item
E(B45) FILTER COEFFICIENT C4 192 E(B46) FILTER COEFFICIENT C5 128 E(B47) FILTER COEFFICIENT C6 128 E(B48) FILTER COEFFICIENT C7 128 E(B49) FILTER COEFFICIENT C8 128 E(B50) NOT USED 0 EC:COMPO.HD E(C01) Y SHOOTLESS/LIMIT RANK 1 E(C02) Y SHOOTLESS/V GAIN 38 E(C03) Y SHOOTLESS/DIAGONAL GAIN 20 E(C04) Y SHOOTLESS/H GAIN 38 E(C05) Y SHOOTLESS/H PEAK FREQ. 2 E(C06) Y SHOOTLESS/V PEAK FREQ. 2 E(C07) Y SHOOTLESS/EDGE CONTROL 12 E(C08) Y SHOOTLESS/POSITIVE and
NEGATIVE GAIN BALANCE E(C09) Y SHOOTLESS/CORING LEVEL 63 E(C10) Y with SHOOT/V GAIN(TYP.) 12 E(C11) Y with SHOOT/
DIAGONAL GAIN(TYP.) E(C12) Y with SHOOT/H GAIN(TYP.) 20 E(C13) Y with SHOOT/H PEAK FREQ. 2 E(C14) Y with SHOOT/V PEAK FREQ. 1 E(C15) Y with SHOOT/EDGE CONTROL 12 E(C16) Y with SHOOT/POSITIVE and
NEGATIVE GAIN BALANCE E(C17) Y ENHANCER/ON 1 E(C18) Y with SHOOT/CORING LEVEL 63 E(C19) Pb ENHANCER/ON 1 E(C20) Pb ENHANCER/LIMIT RANK 1 E(C21) Pb ENHANCER/GAIN 24 E(C22) Pb ENHANCER/PEAK FREQ. 0 E(C23) Pb ENHANCER/CORING LEVEL 63 E(C24) Pr ENHANCER/ON 1 E(C25) Pr ENHANCER/LIMIT RANK 1 E(C26) Pr ENHANCER/GAIN 24 E(C27) Pr ENHANCER/PEAK FREQ. 0 E(C28) Pr ENHANCER/CORING LEVEL 63 E(C29) Y SHOOT ENHANCER/V GAIN(MIN.) 112 E(C30) Y SHOOT ENHANCER/
V GAIN(MAX.) E(C31) Y SHOOT ENHANCER
DIAGONAL GAIN(MIN.) E(C32) Y SHOOT ENHANCER/
DIAGONAL GAIN(MAX.) E(C33) Y SHOOT ENHANCER/H GAIN(MIN.) 112 E(C34) Y SHOOT ENHANCER/
H GAIN(MAX.) E(C35) NOT USED 0 E(C36) NOT USED 0 E(C37) NOT USED 0 E(C38) NOT USED 0 E(C39) NOT USED 0 E(C40) NOT USED 0 E(C41) FILTER COEFFICIENT C0 128 E(C42) FILTER COEFFICIENT C1 128
Setting
value
12
156
112
156
156
Setting No. Setting item
E(C43) FILTER COEFFICIENT C2 128 E(C44) FILTER COEFFICIENT C3 128 E(C45) FILTER COEFFICIENT C4 192 E(C46) FILTER COEFFICIENT C5 128 E(C47) FILTER COEFFICIENT C6 128 E(C48) FILTER COEFFICIENT C7 128 E(C49) FILTER COEFFICIENT C8 128 E(C50) NOT USED 0 ED:RGB-L E(D01) Y SHOOTLESS/LIMIT RANK 1 E(D02) Y SHOOTLESS/V GAIN 32 E(D03) Y SHOOTLESS/DIAGONAL GAIN 32 E(D04) Y SHOOTLESS/H GAIN 32 E(D05) Y SHOOTLESS/H PEAK FREQ. 0
0
E(D06) Y SHOOTLESS/V PEAK FREQ. 0 E(D07) Y SHOOTLESS/EDGE CONTROL 4 E(D08) Y SHOOTLESS/POSITIVE and
NEGATIVE GAIN BALANCE E(D09) Y SHOOTLESS/CORING LEVEL 63 E(D10) Y with SHOOT/V GAIN(TYP.) 20 E(D11) Y with SHOOT/
DIAGONAL GAIN(TYP.) E(D12) Y with SHOOT/H GAIN(TYP.) 20 E(D13) Y with SHOOT/H PEAK FREQ. 0
0
E(D14) Y with SHOOT/V PEAK FREQ. 0 E(D15) Y with SHOOT/EDGE CONTROL 4 E(D16) Y with SHOOT/POSITIVE and
EGATIVE GAIN BALANCE E(D17) Y ENHANCER/ON 1 E(D18) Y with SHOOT/CORING LEVEL 63 E(D19) Pb ENHANCER/ON 1 E(D20) Pb ENHANCER/LIMIT RANK 1 E(D21) Pb ENHANCER/GAIN 24 E(D22) Pb ENHANCER/PEAK FREQ. 0 E(D23) Pb ENHANCER/CORING LEVEL 63 E(D24) Pr ENHANCER/ON 1 E(D25) Pr ENHANCER/LIMIT RANK 1 E(D26) Pr ENHANCER/GAIN 24 E(D27) Pr ENHANCER/PEAK FREQ. 0 E(D28) Pr ENHANCER/CORING LEVEL 32 E(D29) Y SHOOT ENHANCER/V GAIN(MIN.) 104 E(D30) Y SHOOT ENHANCER/
V GAIN(MAX.) E(D31) Y SHOOT ENHANCER/
DIAGONAL GAIN(MIN.) E(D32) Y SHOOT ENHANCER/
DIAGONAL GAIN(MAX.) E(D33) Y SHOOT ENHANCER/H GAIN(MIN.) 104 E(D34) Y SHOOT ENHANCER/
H GAIN(MAX.) E(D35) NOT USED 0 E(D36) NOT USED 0 E(D37) NOT USED 0 E(D38) NOT USED 0 E(D39) NOT USED 0 E(D40) NOT USED 0
Setting
value
0
20
0
152
104
152
152
1-82 (No.YA067)
Page 83
Setting No. Setting item
E(D41) FILTER COEFFICIENT C0 128 E(D42) FILTER COEFFICIENT C1 128 E(D43) FILTER COEFFICIENT C2 128 E(D44) FILTER COEFFICIENT C3 128 E(D45) FILTER COEFFICIENT C4 192 E(D46) FILTER COEFFICIENT C5 128 E(D47) FILTER COEFFICIENT C6 128 E(D48) FILTER COEFFICIENT C7 128 E(D49) FILTER COEFFICIENT C8 128 E(D50) NOT USED 0 EE:RGB-M E(E01) Y SHOOTLESS/LIMIT RANK 1 E(E02) Y SHOOTLESS/V GAIN 32 E(E03) Y SHOOTLESS/DIAGONAL GAIN 32 E(E04) Y SHOOTLESS/H GAIN 32 E(E05) Y SHOOTLESS/H PEAK FREQ. 1 E(E06) Y SHOOTLESS/V PEAK FREQ. 1 E(E07) Y SHOOTLESS/EDGE CONTROL 8 E(E08) Y SHOOTLESS/POSITIVE and
NEGATIVE GAIN BALANCE E(E09) Y SHOOTLESS/CORING LEVEL 63 E(E10) Y with SHOOT/V GAIN(TYP.) 12 E(E11) Y with SHOOT/
DIAGONAL GAIN(TYP.) E(E12) Y with SHOOT/H GAIN(TYP.) 12 E(E13) Y with SHOOT/H PEAK FREQ. 1 E(E14) Y with SHOOT/V PEAK FREQ. 1 E(E15) Y with SHOOT/EDGE CONTROL 8 E(E16) Y with SHOOT/POSITIVE and
NEGATIVE GAIN BALANCE E(E17) Y ENHANCER/ON 1 E(E18) Y with SHOOT/CORING LEVEL 63 E(E19) Pb ENHANCER/ON 1 E(E20) Pb ENHANCER/LIMIT RANK 1 E(E21) Pb ENHANCER/GAIN 24 E(E22) Pb ENHANCER/PEAK FREQ. 0 E(E23) Pb ENHANCER/CORING LEVEL 63 E(E24) Pr ENHANCER/ON 1 E(E25) Pr ENHANCER/LIMIT RANK 1 E(E26) Pr ENHANCER/GAIN 24 E(E27) Pr ENHANCER/PEAK FREQ. 0 E(E28) Pr ENHANCER/CORING LEVEL 32 E(E29) Y SHOOT ENHANCER/V GAIN(MIN.) 112 E(E30) Y SHOOT ENHANCER/
V GAIN(MAX.) E(E31) Y SHOOT ENHANCER/
DIAGONAL GAIN(MIN.) E(E32) Y SHOOT ENHANCER/
DIAGONAL GAIN(MAX.) E(E33) Y SHOOT ENHANCER/H GAIN(MIN.) 112 E(E34) Y SHOOT ENHANCER/
H GAIN(MAX.) E(E35) NOT USED 0 E(E36) NOT USED 0 E(E37) NOT USED 0 E(E38) NOT USED 0
Setting
value
12
152
112
152
152
Setting No. Setting item
E(E39) NOT USED 0 E(E40) NOT USED 0 E(E41) FILTER COEFFICIENT C0 128 E(E42) FILTER COEFFICIENT C1 128 E(E43) FILTER COEFFICIENT C2 128 E(E44) FILTER COEFFICIENT C3 128 E(E45) FILTER COEFFICIENT C4 192 E(E46) FILTER COEFFICIENT C5 128 E(E47) FILTER COEFFICIENT C6 128 E(E48) FILTER COEFFICIENT C7 128 E(E49) FILTER COEFFICIENT C8 128 E(E50) NOT USED 0 EF:RGB-H E(F01) Y SHOOTLESS/LIMIT RANK 1 E(F02) Y SHOOTLESS/V GAIN 32 E(F03) Y SHOOTLESS/DIAGONAL GAIN 32 E(F04) Y SHOOTLESS/H GAIN 32 E(F05) Y SHOOTLESS/H PEAK FREQ. 0 E(F06) Y SHOOTLESS/V PEAK FREQ. 0
0
E(F07) Y SHOOTLESS/EDGE CONTROL 4 E(F08) Y SHOOTLESS/POSITIVE and
NEGATIVE GAIN BALANCE E(F09) Y SHOOTLESS/CORING LEVEL 63 E(F10) Y with SHOOT/V GAIN(TYP.) 20 E(F11) Y with SHOOT/
DIAGONAL GAIN(TYP.) E(F12) Y with SHOOT/H GAIN(TYP.) 20 E(F13) Y with SHOOT/H PEAK FREQ. 0 E(F14) Y with SHOOT/V PEAK FREQ. 0
0
E(F15) Y with SHOOT/EDGE CONTROL 4 E(F16) Y with SHOOT/POSITIVE and
NEGATIVE GAIN BALANCE E(F17) Y ENHANCER/ON 1 E(F18) Y with SHOOT/CORING LEVEL 63 E(F19) Pb ENHANCER/ON 1 E(F20) Pb ENHANCER/LIMIT RANK 1 E(F21) Pb ENHANCER/GAIN 24 E(F22) Pb ENHANCER/PEAK FREQ. 0 E(F23) Pb ENHANCER/CORING LEVEL 63 E(F24) Pr ENHANCER/ON 1 E(F25) Pr ENHANCER/LIMIT RANK 1 E(F26) Pr ENHANCER/GAIN 24 E(F27) Pr ENHANCER/PEAK FREQ. 0 E(F28) Pr ENHANCER/CORING LEVEL 32 E(F29) Y SHOOT ENHANCER/V GAIN(MIN.) 104 E(F30) Y SHOOT ENHANCER/
V GAIN(MAX.) E(F31) Y SHOOT ENHANCER
/DIAGONAL GAIN(MIN.) E(F32) Y SHOOT ENHANCER/
DIAGONAL GAIN(MAX.) E(F33) Y SHOOT ENHANCER/H GAIN(MIN.) 104 E(F34) Y SHOOT ENHANCER/
H GAIN(MAX.) E(F35) NOT USED 0 E(F36) NOT USED 0
Setting
value
0
20
0
152
104
152
152
(No.YA067)1-83
Page 84
Setting No. Setting item
E(F37) NOT USED 0 E(F38) NOT USED 0 E(F39) NOT USED 0 E(F40) NOT USED 0 E(F41) FILTER COEFFICIENT C0 128 E(F42) FILTER COEFFICIENT C1 128 E(F43) FILTER COEFFICIENT C2 128 E(F44) FILTER COEFFICIENT C3 128 E(F45) FILTER COEFFICIENT C4 192 E(F46) FILTER COEFFICIENT C5 128 E(F47) FILTER COEFFICIENT C6 128 E(F48) FILTER COEFFICIENT C7 128 E(F49) FILTER COEFFICIENT C8 128 E(F50) NOT USED 0
Setting
value
1-84 (No.YA067)
Page 85
4.6 ADJUSTMENT PROCEDURE
Item
PDP POWER SUPPLY VOLTAGE
1 2 3
Vs
4
GND
5
GND
6
GND
7
GND
8 9
Va
10
VOLTAGE INDICATION LABEL
MODEL : xxxxxxx All voltage : DC(xx)5V Va : XX V Vs : XXX V 240 / -60 / 100 / -40 / -175 Max Watt : 380W (Full White)
Measuring instrument
DC voltmeter Vs
Vs Vs Vs
NC
CN806
Va
VR351
Va
CN805
MAIN POWER SUPPLY UNIT
Test point Adjustment part Description
Va [MAIN POWER SUPPLY UNIT]
VR551 VR351 [MAIN POWER SUPPLY UNIT]
• Befor adjustment, remove the CN805 / CN806 connector. (1) Connect the DC voltmeter to CN806 connector
1pin(Vs) and 6pin(GND) on the MAIN POWER SUPPLY UNIT.
(2) Switch on the power supply.
VR551
(3) Make sure that a voltage value is within the ±5V of
the value displayed on the panel. (4) When it defer, adjust by VR551. (5) Connect the DC voltmeter to CN806 connector
8pin(Va) and 10pin(GND) on the MAIN POWER
SUPPLY UNIT. (6) Make sure that a voltage value is within the Å}05V of
the value displayed on the panel. (7) When it defer, adjust by VR351.
(8) Shut off the main power. (9) Connect the CN805 and CN806 connector.
(10) In a non-signal state make sure that the voltage of
8
Vs and Va.
(11) When the voltage value is not contained within the
limits of the adjustment value, adjust again.
3
VIDEO DECODER VCO
Remote control unit
Signal generator
[VCO ADJUST PROGRAM]
(1) Input an NTSC colour bar signal from VIDEO A
terminal. (2) Enter the SERVICE MODE, and select "VCO
ADJUST". (3) Select "YES" and press the [] key. Adjustment is
performed automatically. (4) After a few seconds, confirm that "ADJUSTMENT
OK" is displayed on the screen. (5) Turn the power off. Then, turn the power on again,
and confirm that the colour bar signal is properly
displayed.
(No.YA067)1-85
Page 86
Item
A-D INPUT OFFSET (480i)
Offset values
too low
Sate of an
optimum
adjustment
Measuring instrument
Remote control unit
Signal generator
Oscilloscope
Horizontal duration
Picture signal duration
Increase the value
Decrease the value
Test point Adjustment part Description
TP-PR TP-PB [MAIN PWB]
[DEVICE INITIAL BLOCK] I (B19) :Output mode
(1) Input a 480i whole black signal from COMPONENT
terminal. (2) Connect the oscilloscope to TP-PR. (3) Enter the SERVICE MODE, and select "DEVICE
[WHITE BALANCE BLOCK] W(E11) : AD offset R W(E13) : AD offset B
INITIAL VALUE". (4) Select IB : CXA3516R. (5) Select < I(B19) > (Output mode), and change the
setting value from 000 to 001 to 000. (6) Return to the SERVICE MODE, and select "WHITE
BALANCE BLOCK". (7) Select WE : COMPO 15k HIGH.
3.3V
(8) Select < W(E11) > (AD offset R). As is shown in the
left figure, adjust the setting value of < W(E11) > so
that Low(0V) voltage is as bright as High(3.3V)
0V
voltage in the scanning interval. Adjust the setting
value of < W(E11) > within 2-3 points from the initial
value.
3.3V
(9) Connect the oscilloscope to TP-PB.
(10) Select < W(E13) > (AD offset B) of WHITE BALANCE
BLOCK, and adjust the setting value of < W(E13) > so
0V
3.3V
that Low(0V) image signal voltage is as bright as
High(3.3V) voltage in the same way as for < W(E11) >.
Offset values
too hight
A-D INPUT OFFSET (1080i)
Remote control unit
Signal generator
Oscilloscope
TP-PR TP-PB [MAIN PWB]
0V
[DEVICE INITIAL BLOCK] I (B19) : Test mode
[WHITE BALANCE BLOCK] W(G11) : AD offset R W(G13) : AD offset B
(1) Input a 1080i whole black signal from COMPONENT
terminal. (2) Enter the SERVICE MODE, and select "WHITE
BALANCE BLOCK". (3) Select WG : COMPO HIGH. (4) Select < W(G11) > (AD offset R), and adjust in the
same way as for the 480i signal above. (5) Select < W(G13) > (AD offset B), and adjust in the
same way as for the 480i signal above.
1-86 (No.YA067)
Page 87
Item
RGB OFFSET (NTSC)
Measuring instrument
Test point Adjustment part Description
Remote control unit
Signal generator
(RAMP pattern)
Align the 3 lines on the left part
[CPU BLOCK] C(H01) : Test mode
[WHITE BALANCE BLOCK] W(C04) : R cutoff W(C06) : B cutoff
(1) Input an NTSC lamp pattern signal from VIDEO A
terminal.
(2) Enter the SERVICE MODE, and select "CPU
BLOCK". (3) Select CH : Test mode. (4) Select < C(H01) > (Test mode), and change "0" into
"2", and then enter "RGB BALANCE Test mode". (5) Return to the MAIN MENU screen. (6) Select "WHITE BALANCE BLOCK". (7) Select "WC : VIDEO HIGH". (8) Select < W(C04) > (R cutoff) and < W(C06) > (B
cutoff), and adjust the setting values so that the three
lines on the left of the lamp pattern screen are lined
in the same line (so that there is no colour zone in
the border between white and black).
Don't change W(C05) : G cutoff value. (9) After the adjustment finishes, select < C(H01) > of
"CPU BLOCK" again, and return the setting value "2"
to "0".
RGB OFFSET (480i)
RGB OFFSET (1080i)
RGB OFFSET (VGA)
RGB OFFSET (RGB15k)
Remote control unit
Signal generator
Remote control unit
Signal generator
Remote control unit
Signal generator
Remote control unit
Signal generator
[CPU BLOCK] C(H01) : Test mode
[WHITE BALANCE BLOCK] W(E04) : R cutoff W(E06) : B cutoff
[CPU BLOCK] C(H01) : Test mode
[WHITE BALANCE BLOCK] W(G04) : R cutoff W(G06) : B cutoff
[CPU BLOCK] C(H01) : Test mode
[WHITE BALANCE BLOCK] W(A04) : R cutoff W(A06) : B cutoff
[CPU BLOCK] C(H01) : Test mode
[WHITE BALANCE BLOCK] W( I 04) : R cutoff W( I 06) : B cutoff
(1) Input a 480i lamp pattern signal from COMPONENT
terminal. (2) Select "WE : COMPO.15k HIGH". (3) Adjust < W(E04) > (R cutoff) and < W(E06) > (B
cutoff) in the same way as for NTSC.
(1) Input a 1080i lamp pattern signal from
COMPONENT terminal. (2) Select "WG : COMPO. HIGH". (3) Adjust < W(G04) > (R cutoff) and < W(G06) > (B
cutoff) in the same way as for NTSC.
(1) Input a VGA(640 × 480 dots) lamp pattern signal
from PC terminal. (2) Select "WA : RGB PC HIGH". (3) Adjust < W(A04) > (R cutoff) and < W(A06) > (B
cutoff) in the same way as for NTSC.
(1) Input an RGB15k lamp pattern signal from PC input
terminal. (2) Select "W I : RGB 15k HIGH". (3) Adjust < W(I 04) > (R cutoff) and < W(I 06) > (B
cutoff) in the same way as for NTSC.
(No.YA067)1-87
Page 88
Item
WHITE BALANCE (NTSC)
WHITE BALANCE (480i)
WHITE BALANCE (1080i)
Measuring instrument
Remote control unit
Signal generator
Colour analyzer
COLOUR
TEMP.
HIGH
LOW
Remote control unit
Signal generator
Colour analyzer
Remote control unit
Signal generator
Colour analyzer
Test point Adjustment part Description
[WHITE BALANCE BLOCK] (Colour temperature : HIGH) W(C01) : R drive W(C02) : G drive W(C03) : B drive
• Keep the set running for 20 minutes or longer. If you turn the set on again, make adjustment 5 minutes or later after you turn the set on.
• Set PICTURE ADJ. of MAIN MENU to the initial state. (1) Input an NTSC window pattern (brilliance 70%)
signal from VIDEO A terminal.
(2) Set COLOUR TEMP at HIGH in FUNCTION
SELECT of < MAIN MENU >. (Colour temperature : LOW) W(D01) : R drive W(D02) : G drive W(D03) : B drive
(3) Enter the SERVICE MODE. (4) Select "WHITE BALANCE BLOCK". (5) Select "WC : VIDEO HIGH". (6) Select < W(C01) > (R drive) and < W(C03) > (B
drive).
(7) Adjust < W(C01) > and < W(C03) > by using a colour
Colour temperature
adjustment point
X=0.287 Y=0.285
analyzer so that the colour temperature adjustment
point becomes the value in "HIGH" in the left table.
Don't change < W(C02) > (G drive) values.
(8) If the adjustment method above does not work,
return < W(C01) > and < W(C03) > to 255, and fix
X=0.315 Y=0.317
< W(C01) > at 255.
(9) Adjust WHITE BALANCE by using < W(C02) > and
< W(C03) >.
(10) After the adjustment finishes, escape from the
SERVICE MODE.
(11) Switch COLOUR TEMP of < MAIN MENU > to
"LOW".
(12) Enter the SERVICE MODE again. (13) Select WHITE BALANCE BLOCK. (14) Select "WD : VIDEO LOW". (15) Adjust < W(D01) >(R drive), < W(D02) >(G drive),
and < W(D03) >(B drive) by using a colour analyzer
in the same way as for the COLOUR TEMP HIGH
above. [WHITE BALANCE
BLOCK] (Colour temperature : HIGH) W(E01) : R drive W(E02) : G drive W(E03) : B drive
(1) Input a 480i window pattern (brilliance 70%) signal
from COMPONENT terminal.
(2) Set COLOUR TEMP at "HIGH". (3) Select "WE:COMPO.15k HIGH," and adjust
< W(E01) >(R drive), < W(E02) >(G drive),
and < W(E03) >(B drive) in the same way
as for NTSC.
(4) Set COLOUR TEMP at "LOW". (Colour temperature : LOW) W(F01) : R drive W(F02) : G drive
(5) Select "WF : COMPO.15k LOW," and adjust
< W(F01) >(R drive), < W(F02) >(G drive), and < W(F03) >(B drive) in the same as for NTSC.
W(F03) : B drive [WHITE BALANCE
BLOCK] (Colour temperature : HIGH) W(G01) : R drive W(G02) : G drive W(G03) : B drive
(1) Input a 1080i window pattern (brilliance 70%) signal
from COMPONENT terminal. (2) Set COLOUR TEMP at "HIGH". (3) Select "WG : COMPO. HIGH," and adjust < W(G01)
>(R drive), < W(G02) >(G drive), and < W(G03) >(B
drive) in the same way as for NTSC. (4) Set COLOUR TEMP at "LOW". (5) Select "WH : COMPO. LOW," and adjust < W(H01)
(Colour temperature : LOW)
>(R drive), < W(H02) >(G drive), and < W(H03) >(B
drive) in the same way as for NTSC.
W(H01) : R drive W(H02) : G drive W(H03) : B drive
1-88 (No.YA067)
Page 89
Item
WHITE BALANCE (VGA)
WHITE BALANCE (RGB15k)
BRIGHTNESS (NTSC)
Measuring instrument
Remote control unit
Signal generator
Colour analyzer
Remote control unit
Signal generator
Colour analyzer
Remote control unit
Signal generator
Test point Adjustment part Description
[WHITE BALANCE BLOCK] (Colour temperature : HIGH) W(A01) : R drive W(A02) : G drive W(A03) : B drive
(1) Input a VGA (640 × 480 dots) window pattern
(brilliance 70%) signal from COMPONENT terminal. (2) Set COLOUR TEMP at "HIGH". (3) Select "WA : RGB PC HIGH," and adjust < W(A01)
>(R drive), < W(A02) >(G drive), and < W(A03) >(B
drive) in the same way as for NTSC. (4) Set COLOUR TEMP at "LOW". (5) Select "WB : RGB PC LOW," and adjust < W(B01)
(Colour temperature : LOW)
>(R drive), < W(B02) >(G drive), and < W(B03) >(B
drive) in the same way as for NTSC.
W(B01) : R drive W(B02) : G drive W(B03) : B drive
[WHITE BALANCE BLOCK] (Colour temperature : HIGH) W(A01) : R drive W(A02) : G drive W(A03) : B drive
(1) Input an RGB 15k window pattern (brilliance 70%)
signal from COMPONENT terminal. (2) Set COLOUR TEMP at "HIGH". (3) Select "W I : RGB 15k HIGH," and adjust < W( I 01)
>(R drive), < W( I 02) >(G drive), and < W( I 03) >(B
drive) in the same way as for NTSC. (4) Set COLOUR TEMP at "LOW". (5) Select "WJ : RGB 15k LOW," and adjust < W(J01)
(Colour temperature : LOW)
>(R drive), < W(J02) >(G drive), and < W(J03) >(B
drive) in the same way as for NTSC.
W(B01) : R drive W(B02) : G drive W(B03) : B drive
[WHITE BALANCE BLOCK] W(C07) : Bright
• Confirm that white balance adjustment is finished.
• Set PICTURE ADJ. of MAIN MENU at the initial state. (1) Input an NTSC gray scale pattern (1% step) signal
from VIDEO A terminal. (2) Enter the SERVICE MODE. (3) Select WHITE BALANCE BLOCK. (4) Select "WC : VIDEO HIGH". (5) Select < W(C07) >(Bright). (6) Adjust < W(C07) > so that 6% black slightly shines
on the screen.
123456701 2345670
Be careful so that back component does not shine.
Adjust <W(C07)> so that 6% black
5%
shines slightly on the screen.
(No.YA067)1-89
Page 90
Item
BRIGHTNESS (480i)
BRIGHTNESS (1080i)
BRIGHTNESS (VGA)
BRIGHTNESS (RGB15k)
Measuring instrument
Remote control unit
Signal generator
Remote control unit
Signal generator
Remote control unit
Signal generator
Remote control unit
Signal generator
Test point Adjustment part Description
[WHITE BALANCE BLOCK] W(E7) : Bright
[WHITE BALANCE BLOCK] W(G7) : Bright
[WHITE BALANCE BLOCK] W(A7) : Bright
[WHITE BALANCE BLOCK] W(I 7) : Bright
(1) Input a 480i gray scale pattern (1% step) signal from
COMPONENT terminal.
(2) Select "WC : VIDEO HIGH," and adjust < W(E07)
>(Bright) in the same way as for NTSC.
(1) Input a 1080i gray scale pattern (1% step) signal
from COMONENT terminal.
(2) Select "WG : COMPO HIGH," and adjust < W(G07)
>(Bright) as in the same way for NTSC.
(1) Input a VGA(640 × 480 dots) scale pattern (1% step)
signal from PC terminal.
(2) Select "WA : RGB PS HIGH," and adjust < W(A07)
>(Bright) as in the same way for NTSC.
(1) Input a RGB 15k scale pattern (1% step) signal from
COMPONENT terminal.
(2) Select "WI : RBG15k HIGH," and adjust < W( I 07)
>(Bright) as in the same way for NTSC.
1-90 (No.YA067)
Page 91
SECTION 5
TROUBLESHOOTING
5.1 SELF-DIAGNOSIS FUNCTION
5.1.1 OUTLINE
This model has a "Self-diagnosis function," which checks the operation state of the circuits and temperature inside the set, and informs us of a failure and memorize it when a failure occurs. Diagnosis is performed when the power is turned on, and information input to the main microcomputer is monitored at all time. The diagnosis is displayed on the screen and LED flashing. Failure detection is based on input state of I control lines connected to the main microcomputer.
5.1.2 ENTERING SELF-DIAGNOSIS BLOCK
(1) Enter the SERVICE MODE. (See a page for SERVICE
MODE settings). (2) Select DIAGNOSIS BLOCK in the SERVICE MODE. (3) Self-diagnosis block screen is displayed.
2
C bus and various
SERVICE MENU SCREEN
VCO ADJUST WHITE BALANCE BLOCK CPU BLOCK SIZE/POSITION BLOCK H POSITION BLOCK PANEL BLOCK SIGNAL BLOCK DEVICE INITIAL VALUE
ENTER: SELECT: EXIT:
DIAGNOSIS BLOCK UPDATE CPU PROGRAM HOUR METER BLOCK ENHANCER BLOCK
[1/2]
Fig.1
[2/2]
MENU
5.1.3 ESCAPING FROM SELF-DIAGNOSIS BLOCK
(1) To return to the SERVICE MODE screen, press the [EXIT]
key.
5.1.4 INITIALIZATION OF ITEMS IN DIAGNOSIS
(1) Enter the SERVICE MODE. (Fig. 1) (2) Select DIAGNOSIS BLOCK in the second page (2/2). (Fig.
2)
(3) Adjustment screen for DIAGNOSIS BLOCK is displayed.
(Fig. 3) (4) Confirm that all the items are displayed as "O". (5) If an error occurs in an item, "X" and the number of error
times is displayed in the item. Up to nine times of errors are
counted. If errors occur more than nine times, "9" is
displayed. Unless deleted, the number of error times
remains memorized in a memory. (6) To delete an error, select "CLEAR" and press the [] key.
(Fig. 4) (7) Then, items in DIAGNOSIS is initialized, and all items are
displayed as "O". (Fig. 5)
5.1.5 POINTS TO NOTE WHEN USING THE SELF-DIAGNOSIS FEATURE
In addition to circuit failures (abnormal operation), the following cases may also be diagnosed as "Abnormal," and displayed and counted as "X".
(1) Temporary defective transmissions across circuits due to
pulse interruptions
(2) Misalignment in the on/off timing of power for I
2
C bus (Vcc)
when turning on/off the power. Diagonasis may be impeded if I2C SIGNAL BUS, and I2C ROM BUS are displayed as "X". If a failure is expected to reoccur, clear (reset) the failure history to make the unit record the new diagnosis results.
ENTER: SELECT: EXIT:
MENU
Fig.2
SELF-DIAGNOSIS DISPLAY
< DIAGNOSIS BLOCK >
CLEAR I2C SIGNAL BUS : X9 I2C ROM BUS FAN STOP POWER TEMP. OVER TEMP. OVER [90h] TEMP. OVER [92h] TEMP. OVER [94h]
ENTER: EXIT :
< CLEAR >
!
ٌAre you sure ?
"YES" then Key
"NO" then Key
< DIAGNOSIS BLOCK >
CLEAR I2C SIGNAL BUS : I2C ROM BUS FAN STOP POWER TEMP. OVER TEMP. OVER [90h] TEMP. OVER [92h] TEMP. OVER [94h]
ENTER: EXIT :
MENU
: O : : O : O : O : O
: O :
: X9 : O : O : O : O
O
O
Fig.3
Fig.4
Fig.5
MENU
MENU
(No.YA067)1-91
Page 92
5.1.6 DETAILS Type of error Indication Description of detection Countermeasure
Communication error in video decoder, IP conversion, PDP interface etc
C SIGNAL BUS I2C communication errors for various
I
control devices do happen. [IC1101, IC1205, IC1305, IC1310, IC1311, IC1403, IC1501, IC2101,
Memorize the number of error times in the main memory (up to nine times).
2
IC2205, IC2206 etc]
Main memory communication error
2
I
C ROM BUS Communication errors for main memory
do happen. [IC1802]
Memorize the number of error times in the main memory (up to nine times), and turn the power off forcibly. Light or flash LEDs for self-diagnosis indication.
Sub power supply PWB error or cooling fan stop
FUN STOP One or more cooling fan stops, or sub
power supply PWB detects an error.
Memorize the number of error times in the main memory (up to nine times), and turn the power off forcibly. Light or flash LEDs for self-diagnosis indication.
Temperature rise in power supply part
POWER TEMP. OVER
An alarm signal from power supply part is detected (threshold temperature : 110°C). [POWER SUPPLY PART : PTC001]
Memorize the number of error times in the main memory (up to nine times), and turn the power off forcibly.
Light or flash LEDs for self-diagnosis indication. [Q connector 5 pin TEMP_ALM] normal : H, error : L
Temperature rise in MAIN PWB
TEMP. OVER [90h]
A temperature sensor on MAIN PWB detects an error (threshold temperature : 67°C). [IC1810]
Switch of APS control (Reduce brilliance when
the temperature rises).
Display "TEMP/OVER" on the screen.
Memorize the number of error times in the main
memory (up to nine times), and turn the power
off forcibly.
Light or flash LEDs for self-diagnosis indication.
Temperature rise around power supply part
TEMP. OVER [92h]
A temperature sensor in upper part of power supply part detects an error (threshold temperature : 85°C). [IC8201]
Display "TEMP/OVER" on the screen.
Memorize the number of error times in the main
memory (up to nine times), and turn the power
off forcibly.
Light or flash LEDs for self-diagnosis indication.
Temperature rise around sub power supply PWB
TEMP. OVER [94h]
A temperature sensor in upper part of sub power supply PWB detects an error (threshold temperature : 85°C). [IC8301]
Display "TEMP/OVER" on the screen.
Memorize the number of error times in the main
memory (up to nine times), and turn the power
off forcibly.
Light or flash LEDs for self-diagnosis indication.
5.1.7 INDICATION OF SELF DIAGNOSIS BY USING LED
LED for self-diagnosis indication is located on the upper left of the set (on the right of remote sensor).
SELF-DIAGNOSIS AND FLASHING LED
Diagnosis
Flashing LED
Top Middle Bottom
Priority Indication
Communication error in main memory zz7 Notes : Sub power supply PWB error or abnormal cooling
fan stop
zz 2
Abnormal temperature rise in power supply part z z 6 Abnormal temperature rise in MA IN PWB z 5 Abnormal temperature rise around power supply part  z 4 Abnormal temperature rise around sub power
supply PWB
z 3
• Indication color : red
• Flashing interval : 0.25 second
• When two or more errors are detected at the same time, errors are displayed one after another, according to the order of priority.
• All LEDs are lighted while various data are written in the main memory.
Abnormal writing in main memory  1
z : Lighting / : Flashing
1-92 (No.YA067)
Page 93
VICTOR COMPANY OF JAPAN, LIMITED
AV & MULTIMEDIA COMPANY VIDEO DISPLAY CATEGORY 12, 3-chome, Moriya-cho, kanagawa-ku, Yokohama, kanagawa-prefecture, 221-8528, Japan
(No.YA067)
Printed in Japan
WPC
Page 94
MENU INPUT
PLASMA DISPLAY MONITOR
GM-X50U
For Customer Use:
Enter below the Model No. and the Serial No. which is located on the rear panel of the cabinet. Retain this information for future reference.
INSTRUCTIONS
Model No.
Serial No.
LCT1601-001A
Page 95
INSTRUCTIONS
Model GM-X50U
Contents
Safety Precautions .................................................... 2
Parts Identification .................................................... 4
• Monitor: Front View ............................................. 4
• Monitor: Rear Views 1........................................ 5
• Monitor: Rear Views 2........................................ 6
• Remote Control ................................................... 7
Preparations .............................................................. 8
• Checking the Accessories ................................... 8
• Installing the Batteries ......................................... 8
• About the Supplied Ferrite Core ......................... 8
Installation ................................................................. 9
• Precautions ......................................................... 9
Connections ............................................................ 10
• Precautions ....................................................... 10
• Available Signals ............................................... 10
• Connection Diagrams ....................................... 11
• Connecting an External Control Unit ................. 12
• External Speaker Connection ........................... 13
• Connecting the External Cooling Fan Unit ........ 13
Basic Operations ..................................................... 14
• Daily Operations ............................................... 14
• Changing the Aspect Ratio ............................... 15
Video Adjustments .................................................. 16
• Adjusting the Picture Quality ............................. 16
• Adjusting the Screen Size and Position ............ 17
• Adjusting the Color Temperature ....................... 19
• Changing the Aspect Ratio ............................... 19
• Setting the Receivable Signal Types ................. 20
• Setting the COMPONENT/RGB B Input ........... 20
• Changing the Resistance of the RGB B Input
Terminals ........................................................... 21
• Resetting the Function Selection Menu Settings .... 21
Page
Thank you for purchasing this JVC Monitor. Before using the monitor, read this manual carefully so that you know how to use the Monitor correctly. Refer to this manual whenever questions or problems about operation arise. Be sure to read and observe the safety precautions. Keep this manual where the user can see it easily. * Installation and removal require special expertise.
Consult your product dealer for details.
Page
Other Convenient Functions ................................... 22
• Showing On-screen Display .............................. 22
• Showing the On-screen When Changing
the Input Mode .................................................. 23
• Prohibiting the Monitor’s Button Operations...... 23
• Setting the Remote-Controllable Input .............. 24
• Setting the High-Definition Signal Types ........... 24
• Setting the Speed of the Internal Cooling Fan .. 25
• Adjusting the White Balance ............................. 25
• Setting the Clock and the Power On/Off
Timer ................................................................. 26
• Using the Pixel Shift Function ........................... 28
• Using the Power Save Function ........................ 28
• Preventing the Afterimage Effect ...................... 28
• Refreshing the Screen ...................................... 29
• Resetting All the Setup Menu Settings ............. 30
• Resetting All the Menu Settings ........................ 31
• Confirming the Use Time and Model Information ... 31
Menu Classifications ............................................... 32
• Main Menu ........................................................ 32
• Setup Menu ....................................................... 34
Troubleshooting ....................................................... 36
• Self-diagnostic Indication .................................. 37
Specifications .......................................................... 38
1
Page 96
Safety Precautions
FCC NOTICE
CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
IMPORTANT INFORMATION
WARNING:TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
IMPORTANT SAFEGUARDS
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order not to defeat the safeguards incorporated into this product, observe the following basic rules for
its installation, use and service. Please read these “Important Safeguards” carefully before use.
– All the safety and operating instructions should be read before the product is operated. – The safety and operating instructions should be retained for future reference. – All warnings on the product and in the operating instructions should be adhered to. – All operating instructions should be followed. – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
– Use a vacuum cleaner to get rid of the dust around the intakes (all the
openings) on the rear. If a vacuum is not available, use a cloth and wipe it off. Failure to do so will cause internal heat buildup and, therefore, cause damage to the product.
– Do not use attachments not recommended by the product manufacturer as
they may be hazardous.
– Do not use this product near water. Do not use immediately after moving from
a low temperature to high temperature, as this causes condensation, which may result in fire, electric shock, or other hazards.
– Do not place this product on an unstable cart, stand, or table. The product
may fall, causing serious injury to a child or adult, and serious damage to the product. The product should be mounted according to the manufacturer’s instructions, and should use a mount recommended by the manufacturer.
2
Page 97
– When the product is used on a cart, care should be taken to avoid quick stops, excessive force, and
uneven surfaces which may cause the product and cart to overturn, damaging equipment or causing possible injury to the operator.
– Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the
product and protect it from overheating. These openings must not be blocked or covered. (The openings should never be blocked by placing the product on bed, sofa, rug, or similar surface. It should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s instructions have been adhered to.) For proper ventilation, separate the product from other equipment, which may prevent ventilation and keep distance
15
more than 10 cm (3
/16 inches).
– This product should be operated only with the type of power source indicated on the label. If you are not sure of the
type of power supply to your home, consult your product dealer or local power company.
– This product is equipped with a three-wire plug. This plug will fit only into a grounded power outlet. If you are unable to
insert the plug into the outlet, contact your electrician to install the proper outlet. Do not defeat the safety purpose of the grounded plug.
– Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or
against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where they exit from the product.
– For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods
of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power line surges.
– Do not overload wall outlets, extension cords, or convenience receptacles on other equipment as this can result in a
risk of fire or electric shock.
– Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short
out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
– Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltages
and other hazards. Refer all service to qualified service personnel.
– Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions:
a) When the power supply cord or plug is damaged. b) If liquid has been spilled, or objects have fallen on the product. c) If the product has been exposed to rain or water. d) If the product operated normally by following the operating instructions. Adjust only those controls that are covered
by the Operation Manual, as an improper adjustment of controls may result in damage and will often require
extensive work by a qualified technician to restore the product to normal operation. e) If the product has been dropped or damaged in any way. f) When the product exhibits a distinct change in performance – this indicates a need for service.
– When replacement parts are required, be sure the service technician has used replacement parts specified by the
manufacturer or with same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
– Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
15
– The product should be placed more than 30 cm (11
/16 inches) away from heat sources such as radiators, heat
registers, stoves, and other products (including amplifiers) that produce heat.
– When connecting other products such as VCR’s, and personal computers, you should turn off the power of this product
for protection against electric shock.
– Do not place combustibles behind the cooling fan. For example, cloth, paper, matches, aerosol cans or gas lighters that
present special hazards when over heated.
– Use only the accessory cord designed for this product to prevent shock.
Option terminal: This terminal is intended exclusively to be used to drive the fan motor.
Do not connect any plugs to the terminal other than JVC’s recommended optional parts.
Polarity of terminal
POWER CONNECTION
The power supply voltage rating of this product is AC 120 V. Do not use other power cords than the power cord attached to this unit.
For U.S.A. and Canada: AC 120 V
3
Page 98
MENU INPUT
12
MENU INPUT
MENU INPUT
3456
Parts Identification
Monitor: Front View
Bottom View
1 Remote sensor/power lamp
Point the front end of the wireless remote control toward here. When the Monitor is turned on, the power lamp glows green. It glows orange in standby mode.
2 Self-diagnostic lamps (page 37)
These lamps light/flash if something abnormal occurs with the Monitor.
3 2 / 3 / 5 / buttons
Use these buttons to select menu items and to make adjustments.
• When no menu is displayed, you can use the 2 / 3
buttons to adjust the volume level.
4 MENU button
Use this button to display or erase menus. While a sub-menu is displayed, pressing this button will move you one screen back to the preceding menu.
5 INPUT button (page 14)
Use this button to switch between inputs. To select the COMPONENT or RGB B input, you have to set “COMPO./RGB B” correctly on the menu (see page
20).
button (page 14)
6
Use this button to turn on and off (on standby) the Monitor when the POWER switch on the rear of the Monitor is “| (on).”
4
Page 99
Monitor: Rear Views 1
1 2 3
VIDEO A
VIDEO
IN OUT
AUDIO
L/MONO
R
VIDEO B
VIDEO
IN Y/C IN
COMPONENT/RGB B
VIDEO
Y/G Pb/B Pr/R HD/Cs VD
AUDIO
L/MONO
R
AUDIO
L/MONO
R
1 VIDEO A terminals (page 11)
AUDIO (L/MONO, R) input terminals (pin jack)
Connect these terminals to the audio input terminals of a VCR, etc.
VIDEO IN terminal (BNC)
Connect this terminal to the video output terminal of a VCR, etc.
VIDEO OUT terminal (BNC)
Connect this terminal to the video input terminal of another monitor, etc.
Note:
Since the video output terminals on this Monitor are loop-through terminals, the devices connected to this video output terminal should be correctly terminated. Otherwise, pictures become abnormally bright or the Monitor screen gets affected abnormally.
2 VIDEO B terminals (page 11)
AUDIO (L/MONO, R) input terminals (pin jack)
Connect these terminals to the audio output terminals of a VCR, etc.
Y/C (S video) IN terminal (mini DIN 4pin)
Connect this terminal to the S-video output terminal of a VCR, etc.
VIDEO IN terminal (pin jack)
Connect this terminal to the video output terminal of a VCR, etc.
Note:
When both the video and S-video terminals are connected, the S-video terminal will have priority.
3 COMPONENT/RGB B input terminals (page 11)
AUDIO (L/MONO, R) input terminals (pin jack)
Connect these terminals to the audio output terminals of the other equipment.
G, B, R, HD/Cs, VD (VIDEO) input terminals (BNC)
Connect these terminals to the following output terminals of a personal computer or other equipment:
Analog RGB signal output terminalsHorizontal sync (HD) signal or composite (Cs) signal
output terminal
– Vertical sync (VD) signal output terminal
Notes:
External sync signals are automatically detected when they come in.
When both horizontal (HD)/vertical (VD) sync and composite (Cs) sync are connected, HD/VD sync signals will be used.
Y, Pb, Pr (VIDEO) input terminals (BNC)
Connect these terminals to the component signal output terminals of NTSC or high-vision equipment.
Note:
When these terminals are used as the component terminals (Y, Pb, Pr)—see “Setting the COMPONENT/ RGB B Input on page 20, external sync signals (HD/Cs, VD) cannot be used.
5
Page 100
Parts Identification (Continued)
AC INAUDIO
L
OUT
R
RGB A
AUDIO
IN
REMOTE
RS-232C
WIRED
MAKE
POWER
EXTERNAL
R
SPEAKER OUT
L
INTERNAL
OPTION
4 5 6 7 8
2
3
1
Monitor: Rear Views 2
1 OPTION terminal (page 13)
Connect the power cord of the Cooling Fan Unit (not supplied) when installing the Monitor vertically.
2 SPEAKER OUT L/R terminals (page 13)
Connect external speakers, such as unique JVC speakers (not supplied), etc.
3 INTERNAL/EXTERNAL (built-in speaker/external
4 RGB A input terminals (page 12)
speaker) selecting switch (page 13)
INTERNAL: To use built-in speakers. EXTERNAL: To use external speakers.
Input terminal (D-sub, 15 pin)
Connect to the video output terminal of a personal computer.
Note:
Use a cord as short as possible when connecting a personal computer to this terminal. (Recommended length is within 3 m.)
AUDIO IN terminal (stereo mini jack)
Connect to the audio output terminal of a personal computer.
5 REMOTE terminals (page 12)
RS-232C terminal (D-sub, 9 pin)
Connect to the RS-232C terminal of a personal computer. For the control method using this terminal, consult an authorized JVC dealer.
MAKE terminal (mini DIN, 4pin)
Connect an external control unit. (See page 12.)
WIRED terminal (stereo mini jack)
Connect a wired remote control unit to this terminal.
Note:
When the above three terminals are used at the same time, transmitted commands through the MAKE terminal have priority over those through the other terminals.
6 AUDIO OUT terminals (pin jack) (page 12)
Connect to the audio input terminals of external equipment such as an amplifier.
7 AC IN terminal (page 12)
Connect the supplied power cord to this terminal.
8 POWER switch (page 14)
When this switch is set to | (on), you can turn on and off (on standby) the Monitor by using the POWER button on the remote control or the button on the Monitor.
6
Loading...