JVC GMV42C/PLASMA, GMV42E, GMV42EB, GMV42PCC, GMV42PCE/PLASMA Service manual & schematics

SERVICE MANUAL

PLASMA DISPLAY MONITOR

YA06420043

GM-V42C

BASIC CHASSIS

T4

RM-C579 REMOTE CONTROL UNIT

ON

POWER

OFF

ASPECT

DISPLAY

INPUT SELECT

COMPO.

A

/(RGB B)

VIDEO

RGB AB

MUTING

VOLUME

MENU/EXIT

MENU INPUT POWER

TABLE OF CONTENTS

1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22

5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-58

No.YA064

2004/3

SPECIFICATION

Items Contents

Type Plasma display

Dimension (W × H × D) 103.5cm × 64.0cm × 8.9cm

Mass 35.1kg Video System VIDEO A/B NTSC3.58, NTSC4.43, PAL, PAL60, SECAM

COMPONENT 480i, 576i, 480p, 576p, 720/60p, 1080/50i, 1080/60i (1035/60i) Power Requirements AC220V, 50Hz / 60Hz Rated Input Current 1.4A

Operation Environment Temperature : 0°C ~ 40°C

Storage Environment Temperature : -20°C ~ +60°C

Plasma Display Panel

Effective Screen Dimensions

Speaker 4cm × 7cm oval type, 8Ω Audio power output Speaker output : 3W+3W (TYP at impedance 6Ω)

Input / Output Terminals

Accessories Remote control unit (RM-C579) × 1, AA/R6-size dry cell battery × 2(for operation check)

Design and specifications are subject to change without notice.

1-2 (No.YA064)

Pixel Number

Pixel Pitch

Cell Pitch

Display Colours

Aspect Ratio

VIDEO A

(IN / OUT)

VIDEO B

(INPUT)

RGB A (INPUT)

COMPONENT/

RGB B (INPUT)

AUDIO OUT Output impedance 600Ω, RCA pin jack × 2

SPEAKER OUT Impedance 6Ω ~ 8Ω (L/R)

REMOTE RS-232C D-sub 9-pin connector × 1

OPTION DC Power supply for cooling fan (DC15V), DC jack × 1

Relative humidity : 20% ~ 80% (non-condensing) Pressure : 700hPa ~ 1114hPa

Relative humidity : 10% ~ 85%(non-condensing) Pressure : 300hPa ~ 1114hPa

Diagonal : 107.4cm, (W) 93.3cm × (H) 53.3cm Horizontal 852 × Vertical 480 (W-VGA) Horizontal 1.095mm × Vertical 1.110mm Horizontal 0.365mm × Vertical 1.110mm

16,777,216 colours (256 colours for each of RGB) 16:9 (Wide format)

Video input 1V(p-p) / 75Ω, BNC connector × 1 Video output 1V(p-p) / 75Ω, BNC connector × 1 Audio input 500mV(rms) / high impedance, RCA pin jack × 2(L/R) Y/C Mini-DIN 4pin connector × 1

Video 1V(p-p) / 75Ω, RCA pin jack × 1 Audio 500mV(rms) / high impedance, RCA pin jack × 1

[ Horizontal sync (HD) ] [ Composite sync (Cs) ]

[ Vertical sync (VD) ]

Audio 500mV(rms) / high impedance, 3.5mm stereo mini jack × 1 COMPONENT BNC connector × 3

RGB

[Analog RGB]

HD [ Horizontal sync ] Cs [ Composite sync ]

VD [ Vertical sync ]

Audio 500mV(rms) / high impedance, RCA pin jack × 2

MAKE Mini-DIN 4pin connector × 1 WIRED 3.5mm stereo mini jack × 1

Remote control cable × 1, Power cord (approx 2.5m) × 3

Y : 1V(p-p) / 75Ω C : 0.286V(p-p) / 75Ω [NTSC]

0.3V(p-p) 75Ω [PAL/SECAM]

D-sub 3-row 15-pin connector × 1 R / G / B : 0.7V(p-p) / 75Ω

RGB

G on sync : 1V(p-p) / 75Ω (negative syncy) HD : 0.3V(p-p) ~ 5V(p-p) / 470Ω (positive / negative polarity) Cs : 0.3V(p-p) ~ 5V(p-p) / 470Ω (positive / negative polarity) VD : 1V(p-p) ~ 5V(p-p) / 470Ω (positive / negative polarity)

Y : 1V(p-p) / 75Ω Pb/B-Y : 0.7V(p-p) / 75Ω Pr/R-Y : 0.7V(p-p) / 75Ω

BNC connector × 5 R : 0.7V(p-p) / 75Ω G : 0.7V (p-p) / 75Ω G on sync : 1V(p-p) / 75Ω (negative sync) B : 0.7V (p-p) / 75Ω

0.3V(p-p) ~ 5V(p-p) / 1kΩ (positive / negative polarity) / 75Ω

0.3V(p-p) ~ 5V(p-p) / 1kΩ (positive / negative polarity) / 75Ω 1 V(p-p) ~ 5V(p-p) / 1kΩ (positive / negative polarity) / 75Ω

SECTION 1

PRECAUTION

1.1 SAFETY PRECAUTIONS

(1) The design of this product contains special hardware,

many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Service should be performed by qualified personnel only.

(2) Alterations of the design or circuitry of the products should

not be made. Any design alterations or additions will void the manufacturer's warranty and will further relieve the manufacturer of responsibility for personal injury or property damage resulting therefrom.

(3) Many electrical and mechanical parts in the products have

special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the parts list of Service manual. Electrical components

having such features are identified by shading on the schematics and by ( ) on the parts list in Service manual. The use of a substitute replacement which does

not have the same safety characteristics as the recommended replacement part shown in the parts list of Service manual may cause shock, fire, or other hazards.

(4) Don't short between the LIVE side ground and

ISOLATED (NEUTRAL) side ground or EARTH side ground when repairing.

Some model's power circuit is partly different in the GND. The difference of the GND is shown by the LIVE : ( ) side GND, the ISOLATED (NEUTRAL) : ( ) side GND and EARTH : ( ) side GND. Don't short between the LIVE side GND and ISOLATED (NEUTRAL) side GND or EARTH side GND and never measure the LIVE side GND and ISOLATED (NEUTRAL) side GND or EARTH side GND at the same time with a measuring apparatus (oscilloscope etc.). If above note will not be kept, a fuse or any parts will be broken.

(5) If any repair has been made to the chassis, it is

recommended that the PDP voltage setting should be checked or adjusted.

(6) When service is required, observe the original lead dress.

Extra precaution should be given to assure correct lead dress in the high voltage circuit area. Where a short circuit has occurred, those components that indicate evidence of overheating should be replaced. Always use the manufacturer's replacement components.

(7) Isolation Check (Safety for Electrical Shock Hazard)

After re-assembling the product, always perform an isolation check on the exposed metal parts of the cabinet (antenna terminals, video/audio input and output terminals, Control knobs, metal cabinet, screw heads, earphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.

a) Dielectric Strength Test

The isolation between the AC primary circuit and all metal parts exposed to the user, particularly any exposed metal part having a return path to the chassis should withstand a voltage of 3000V AC (r.m.s.) for a period of one second. (. . . . Withstand a voltage of 1100V AC (r.m.s.) to an appliance rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated 200V or more, for a period of one second.) This method of test requires a test equipment not generally found in the service trade.

b) Leakage Current Check

Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Using a "Leakage Current Tester", measure the leakage current from each exposed metal part of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground (water pipe, etc.). Any leakage current must not exceed 0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.2mA AC (r.m.s.).

Alternate Check Method

Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Use

an AC voltmeter having 1000Ω per volt or more sensitivity in the following manner. Connect a 1500Ω 10W resistor paralleled by a 0.15µF AC-type capacitor

between an exposed metal part and a known good earth ground (water pipe, etc.). Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Any voltage measured must not exceed 0.75V AC (r.m.s.). This corresponds to

0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.3V AC (r.m.s.). This corresponds to 0.2mA AC (r.m.s.).

AC VOLTMETER (HAVING 1000 /V, OR MORE SENSITIVITY)

0.15 F AC-TYPE

GOOD EARTH GROUND

1500 10W

PLACE THIS PROBE ON EACH EXPOSED ME TAL PAR T

(No.YA064)1-3

1.2 INSTALLATION

1.2.1 REQUIREMENTS FOR SETTING

The following minimum space must be kept when a PDP is installed. (The recommended distance should be from the most projected portion when a PDP is inclined.) An insufficient space reduces cooling efficiency and raises the internal temperature. If the internal temperature rises over the reference value, the temperature sensor works to turn the power off for protecting the main body. Therefore, vents on the backside of the main body such as heat dissipation vents must not be blocked, and sufficient spaces for heat dissipation must be kept around the main body.

Methods of Installation

1

Hanging from a wall [Horizontal]

2

Hanging from a wall [Vertical]

10cm

Front

Wall

20cm

15cm

10cm10cm

10cm

Flank Remarks

Front Wall

5cm

Wall

5cm

It is necessary to set the cooling fan where install each side causes high temperature within a PDP and may damage the inner circuit.

Do not prevent the radiation of heat from back, top and flank sides of a PDP. Preventing the radiation of heat from each side causes high temperature within a PDP and may damage the inner circuit.

Install a PDP in a place where is well ventilated. Ambient temperature should be within a range of 0 ~40 .

An exclusive fixture (option) should be used.

3

Suspension from a ceiling

4

Desktop

10cm

Wall

15cm

10cm10cm

15cm

10cm10cm

Front

The structure and strength of the wall where a PDP is installed should be checked beforehand so as to install the PDP safety without any accident.

Wall

5cm

A PDP should be installed on a rigid floor or stand.

In order to prevent a PDP from turning over by an accident or earthquake, safety measures should be considered.

Wall

5cm

1-4 (No.YA064)

1.2.2 PRECAUTION DURING NOTES FOR TRANSPORTATION

A

When transporting the display unit, pressure exerted on the internal PDP (Plasma Display Panel) due to improper handing (such as tossing and dropping) may cause damages even when the unit is carefully packed. To prevent accidents from occurring during transportation, pay careful attention prior to delivery such as through exchanging the handing instructions to transporters. Ensure that the following requirements are met during transportation, as the PDP of this unit is made of glass and therefore fragile.

(1) Avoid vibrations and impacts

The unit may be broken if it is toppled sideways even when properly packed. Ensure that the unit is carried by at least 2 persons and pay careful attention not to exert any vibration or impact on it.

(2) Do not place equipment lay a PDP on its side.

A PDP should always be placed upright during both transportation and safekeeping. Don't lay it on its side. The panel of a PDP is very fragile to the impact in the horizontal direction. When a car carries a PDP, load it on board the car in parallel with the moving direction of the car. Don't lay several PDPs one on top another. During safekeeping, don't lay more than two PDPs one on top another even if they are kept upright.

1.2.4 RETAINED-IMAGE / BURN-IN ON SCREEN

Like CRTs, "burn-ins" may occur when a same image is continuously displayed over an extended period of time. As this may also shorten the life span of the PDP. Therefore, turn off the display when not in use, scroll the screen, make use of screen-savers, or allow even distribution on the display by inverting the brightness, switching to complementary colors or inverting animated images at periodic intervals. As burn-in is more likely to occur with high brightness and contrast settings, try to use neutral gradations or medium tone colors. Burn-in dose not occur in the case of animated images. When switching to another image after continuous display of the previous image, residual images may become prominent, as luminance in a part of the display is higher then the other parts. This is not a defect but is because due to the discharge surface of the lighted portion has become being relatively activated and its luminance higher than the unlighted parts.

1.2.5 BRIGHTNESS CHANGE IN THE SCREEN

In order to save the power consumption, the power is controlled (with APS function) depending on the brightness of the screen. For this, the brightness may change after a short time when the picture of the screen is changed. However, this phenomenon is not a trouble.

1.2.3 PRECAUTIONS ON INSTALLATION To get good heat dissipation from the rear.

This Monitor is not equipped with cooling fans because it is designed to operate quietly. If you install the Monitor in such a way as not instructed, additional methods are required to cool down the Monitor.

1.2.6 INFRARED RAYS

Because the near infrared rays (800nm~1000nm) radiate from the panel face, the neighboring infrared ray remote controllers, infrared communication systems, etc. may malfunction. In these cases, take a measure to prevent the trouble to be caused by direct rays (or reflected rays) from the screen by changing the direction of the screen face or keeping a safe distance between

: Horizontal Installation (Normal)

In the case, the slots and openings in the cabinet protect the Monitor from overheating. * See also "Requirements forsetting"

on page 6 in the instruction.

a PDP and other devices.

1.2.7 OPTICAL FILTER (FRONT FILTER)

Avoid placing the unit under direct sunlight over a prolonged period of time. This may cause the optical filter to deteriorate in quality and color. Clean the filter surface by wiping it softly lightly with outing flannels a soft and lightly fuzz cloth (such a flannel).

B : Vertical Installation

It is required to attach the Cooling Fan Unit (TS-C01FANG : option). * Refer to the following figure for how to attach the cooling fan unit.

An option terminal is exclusively for a cooling fan. Please do not use it for connection with other apparatus.

Do not use solvents such as benzene or thinner to wipe the filter surface. This may cause the filter to deteriorate in quality or the coating on the surface to come off. As the filter surface is fragile. Do not scratch or hit it with hard materials.

1.2.8 NOTES PRECAUTIONS FOR REPLACEMENT OF EXTERIOR PARTS

Take note of the following when replacing exterior parts (back

Cooling Fan Unit (Option)

OPTION

POWERAC INAUDIO

L

R

OUT

MAKE

WIRED

RS-232C

REMOTE

L

SPEAKER OUT

AUDIO

IN

RGB A

REAR COVER, FRONT PANEL, OPTICAL FILTER): Do not exert pressure on the front of the PDP(glass surface). Pay careful attention not to scratch or stain the front of the PDP (surface) with hands. When replacing exterior parts, the front of the PDP should be placed facing downward. Place a met, etc. underneath to avoid causing scratched to the front surface. However, never use materials that are too soft (such as blanket cloth). If replacement is made with the PDP surface facing downward and in contact with the blanket, pressure may be exerted on the PDP, thus causing damages to it.

(No.YA064)1-5

SPECIFIC SERVICE INSTRUCTIONS

2.1 TIMING SPECIFICATION & SCAN SIZE

Divide Item

COMPOSITE

Y/C

COMPONENT

PC/RGB 15k

PC/VGA 400

PC/VGA 480

PC/SVGA

PC/XGA

NTSC, PAL60,

NTSC4.43

(B/W 60Hz)

PAL, SECAM

(B/W 50Hz)

480i

576i

480p SMPTE 293M 59.94 31.468 27.00 858 525 720 483

576p SMPTE 293M 50.00 31.250 27.00 864 625 720 575

720p SMPTE 296M 60.00 45.000 74.25 1650 750 1280 720 FULL 95.00 95.00 1080/50i SMPTE 274M 50.00 28.125 74.25 2640 562.5 1920 540 FULL 95.00 95.00 1080/60i SMPTE 274M 60.00 33.750 74.25 2200 562.5 1920 540 FULL 95.00 95.00

1035i BTA S-001A 60.00 33.750 74.25 2200 562.5 1920 517.5 FULL 92.75 92.75

RGB 15k/60Hz 59.94 15.734 14.32 910 525 768 485

RGB 15k/50Hz 50.00 15.625 17.73 1135 625 922 575

PC98 (NEC) 56.42 24.82 21.05 848 440 640 400

VGA400/70 (IBM) 70.09 31.47 25.18 800 449 640 400

VGA-60 (Industry std.) 59.94 31.47 25.17 800 525 640 480

VGA-72 VESA std. 72.81 37.86 31.50 832 520 640 480

VGA-75 VESA std. 75.00 37.50 31.50 840 500 640 480

MAC 13" (Apple) 66.67 35.00 30.24 864 525 640 480

SVGA-56

SVGA-60

SVGA-72

SVGA-75

XGA-60

XGA-70 VESA STD. 70.07 56.48 75.00 1328 806 1024 768

XGA-75 VESA STD. 75.03 60.02 78.75 1312 800 1024 768

XGA-85 VESA STD. 85.00 68.68 94.50 1376 808 1024 768

XGA+-75 VESA STD. 75.00 67.50 108.0 1600 900 1152 864

Standard

SMPTE 244M

ITU-R BT601-4

(CCIR Rec.601)

ITU-R BT601-4

(CCIR Rec.601)

VESA GUIDELINES

SECTION 2

Input picture format Scan size

Frequency Total pixel Visible area pixel

Vert. Hor.

fVi fHi fci Hi Vi Hai Vai Kh Kv Hz kHz MHz

59.94 15.734 14.32 910 525 768 485

50.00 15.625 17.73 1135 625 922 575

59.94 15.734 13.50 858 525 720 485

50.00 15.625 13.50 864 625 720 575

56.25 35.16 36.00 1024 625 800 600

60.32 37.88 40.00 1056 628 800 600

72.19 48.08 50.00 1040 666 800 600

75.00 46.88 49.50 1056 625 800 600

60.00 48.36 65.00 1344 806 1024 768

Dot clock

Hor.Vert.Hor.Vert.

pixel/line line/frame pixel/line line/frame

Display mode

REGULAR 95.00 95.00

FULL 95.00 95.00

PANORAMIC 95.00 90.00

ZOOM 95.00 71.25

REGULAR 95.00 95.00

FULL 95.00 95.00

PANORAMIC 95.00 90.00

ZOOM 95.00 71.25

REGULAR 95.00 95.00

FULL 95.00 95.00

PANORAMIC 95.00 90.00

ZOOM 95.00 71.25

REGULAR 95.00 95.00

FULL 95.00 95.00

PANORAMIC 95.00 90.00

ZOOM 95.00 71.25

REGULAR 95.00 95.00

FULL 95.00 95.00

PANORAMIC 95.00 90.00

ZOOM 95.00 71.25

REGULAR 95.00 95.00

FULL 95.00 95.00

PANORAMIC 95.00 90.00

ZOOM 95.00 71.25

REGULAR 95.00 95.00

FULL 95.00 95.00

PANORAMIC 95.00 90.00

ZOOM 95.00 71.25

REGULAR 95.00 95.00

FULL 95.00 95.00

PANORAMIC 95.00 90.00

ZOOM 95.00 71.25

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

REGULAR 100.00 100.00

FULL 100.00 100.00

Hor. Vert.

%%

1-6 (No.YA064)

2.2 TECHNICAL INFORMATION

2.2.1 PDP (PLASMA DISPLAY PANEL) DESCRIPTION

2.2.1.1 CAUTION

Although a PDP is made with highly advanced precision, this does not necessarily mean all of the cells operate correctly. The PDP inevitably includes cell that do not light or light constantly. If the specifications (PDP performance) are unclear at the time of shipment, an adequate description cannot be conveyed to the customer. In event of inquiries from customers regarding PDP performance, check the following specifications in order to offer a suitable reply.

2.2.1.2 CELL ARRANGEMENT

The PDP is constructed of front and rear glass substrates provided with respective discharge electrodes. Between these, neon for discharging and xenon for generating ultraviolet rays are enclosed. One picture element (pixel) is composed of Red, Green and Blue (RGB) cells. The cell pitch is 0.365mm horizontal (1.095mm per pixel) by 1.110mm vertical. As shown in Fig. 1, the cells are arranged for each R / G / B colour. A pixel consists of each cell of R/G/B/ colour. The size of a cell is

0.365mm horizontally and 1.110mm vertically.

Direction

Vertical(V)

1st pixel

2nd pixel

479th pixel

480th pixel

Horizontal(H)

line

1st pixel

array

B G R B G R

BG

G RBG R

B

GRBGR

B

H 1.095mm

Pitch of pixel

2nd pixel

array

RBG R

Fig.1 PIXEL (CELL) ARRANGEMENT

One pixel

(1dot)

B cell G cell R cell

851th pixel

array

B GRBG R

BGRBGR

G RBG R

B

GRBGR

B

852th pixel

array

H 0.365mm Pitch of cell

V 1.110mm Pitch of pixel (Pitch of cell)

(No.YA064)1-7

2.2.1.3 PIXEL FAULT

There are three pixel faults - bright fault , dark fault and flicker fault - that are respectively defined as follows.

(1) BRIGHT FAULT

In this pixel fault, a cell that should not light originally is lighting on and off. For checking this pixel fault, input ALL BLACK SCREEN and find out the cell that is lighting on and off.

(2) DARK FAULT

In this pixel fault, a cell that should light originally is not lighting or lighting with the brightness twice as brighter as originally lighting. For checking this pixel fault, input 100% of each R/G/B colour and find out the cell that is not lighting.

(3) FLICKER FAULT

In the pixel fault, a cell that should light originally or not light originally is flashing on and off. For checking this pixel fault, input ALL BLACK SCREEN signal or 100% of each RGB colour and find out the cell that is flashing on and off.

2.2.1.4 PIXEL FAULT SPECIFICATION

Fault Screen display Criteria for number of faulted cell

BRIGHT FAULT All black screen A zone: 0

B zone: 1 or less than 1 in each colour

DARK FAULT Red level 100% on entire screen A zone: 2 or less than 2 in each colour

Green level 100% on entire screen

B zone: 6 or less than 6 in each colour

Blue level 100% on entire screen

FLICKER FAULT Red level 100% on entire screen A zone: 0

Green level 100% on entire screen

B zone: 2 or less than 2 in each colour

Blue level 100% on entire screen

(1) OBJECT RANGE

A-zone : Center portion (area enclosed by 1/4 vertically from the top and bottom and 1/4 horizontally from the right and left sides.) B-zone : Other area

1/4H 1/4H

B zone

1/4V

A zone

1/4V1/4V

(2) JUDGEMENT STANARD

Regardless of A and B zones, the following cases are considered as defects.

• When the distance between the bright fault is less than 15mm.

• When the distance between the bright fault and the dark defect or between the flicker fault is less than 15mm.

• When the distance between the dark fault and the flicker is less than 30mm.

1-8 (No.YA064)

2.2.2 REMOTE THROUGH FUNCTION

The REMOTE THROUGH function is a function that is capable of controlling such equipment as a karaoke system connected to the REMOTE THROUGH terminal by receiving the IR (infrared ray) signal at the sensor of the remote controller unit of this model.

2.2.2.1 REMOTE THROUGH OUTPUT TERMINAL

The REMOTE THROUGH terminal and MAKE (mini DIN 4 pin) terminal at the back of the main body share the same terminal. Therefore, it is necessary to change the setup at the SERVICE MODE when the REMOTE THROUGH function is used. For the pin layout at the terminal, the 4 pin will become an output terminal and the 1-3 pins will be GNDs.

REMOTE THROUGH OUTPUT TERMINAL

34

Pin No.

1

2

3

2

1

4

Signal name

GND

OUTPUT

2.2.2.2 HOW TO CHANGE THE SETUP OF THE FUNCTION

(1) Enter the SERVICE MODE. (2) Select the < CPU BLOCK > with the [/] key. (3) Press the [] key of the remote control unit to display the < CPU BLOCK >. (4) Select the "CE: SYSTEM CONSTANT" with the [/] key. (5) Press the [] key of the remote control unit to display the setup screen for the "SYSTEM CONSTANT". (6) Display the "CE 05" with the [/] key. (7) Change the setup value to 001 from 000 with the [/] key. (8) Press the MENU key of the remote control unit to exit from the SERVICE MODE. (9) After turning the power off (or at the stand-by mode), turn the power on again.

(10) Then the REMOTE THROUGH function is available.

SERVICE MODE

VCO ADJUST WHITE BALANCE BLOCK CPU BLOCK SIZE/POSITION BLOCK H POSITION BLOCK PANEL BLOCK SIGNAL BLOCK DEVICE INITIAL VALUE

ENTER: SELECT: EXIT:

[1/2]

MENU

DIAGNOSIS BLOCK UPDATE CPU PROGRAM HOUR METER BLOCK ENHANCER BLOCK

ENTER: SELECT: EXIT:

[2/2]

MENU

< CPU BLOCK >

CA:PANORAMA DATA CB:SIGNAL RANGE CC:SIZE/POSI. RANGE CD:FRQENCY DATA CE:SYSTEM CONSTANT CF:TEMP. SENSOR DATAs CG:APS CONTROL DATA CH:TEST MODE

ENTER: SELECT: EXIT:

<CPU BLOCK> screen

MENU

C(E05)

SYSTEM CONSTANT screen

000 001

(No.YA064)1-9

2.2.3 HOUR METER FUNCTION

This model is equipped with an "HOUR METER" function that displays elapsed time on operating time of the set. Elapsed time can be checked at the "HOUR METER BLOCK" in the SERVICE MODE. Also you can reset elapsed time to zero if needed. Elapsed time count 1 hour. MAX elapsed time is 65535 hour.

 HOW TO RESET ELAPSED TIME

(1) Enter the SERVICE MODE (Fig.1). (2) Press [/] key, and select "HOUR METER BLOCK" of

SERVICE MODE 2 page (Fig.2).

(3) Press [] key, and display "HOUR METER BLOCK"

screen (Fig.3).

(4) While the "HOUR METER BLOCK" display press []

key and it will display "RESET HOUR METE" (Fig.4).

(5) Press [] key and reset the HOUR METER (Fig.5).

SERVICE MODE

VCO ADJUST WHITE BALANCE BLOCK CPU BLOCK SIZE/POSITION BLOCK H POSITION BLOCK PANEL BLOCK SIGNAL BLOCK DEVICE INITIAL VALUE

ENTER: SELECT: EXIT:

[1/2]

MENU

Fig.1

2.2.4 REMINDER TO CHANGE A BATTERY

This model with a timer function, is equipped with a battery for the timer. When the battery is running low, a message of "BATTERY LOW" is displayed on the [TIMER], [COLOR-REVERSE] and [REFRESH] setting screen of the < SET-UP MENU >. At the end of the battery-life, a message of "BATTERY EMPTY" is displayed same screen. Both cases, you should make a battery change. Battery is fixed on the battery board. Please exchange the whole substrate.

 BATTERY CHANGE PROCEDURE

(1) Remote the terminal board on the back of the main body.

(Refer to disassembly procedure) (2) Remove the connector D on the battery board. (3) Remove the screw A attaching the battery board. (4) Change the battery board to new one.

Note :

After changing the battery board, the same message before a battery change will be displayed when the power is turned on for the first time. Therefore, turn off the power once, then turn on the power again. The message will be disappeared and you can use the model with normal functions.

AV TERMINAL

DIAGNOSIS BLOCK UPDATE CPU PROGRAM HOUR METER BLOCK ENHANCER BLOCK

ENTER: SELECT: EXIT:

HOUR METER BLOCK

< HOUR METER BLOCK >

RESET HOUR METER (X1h) : 12345

ENTER: EXIT:

< RESET HOUR METER >

!

Are you sure ?

"YES" then Key

"NO" then Key

ENTER: SELECT: EXIT:

MENU

[2/2]

MENU

Fig.2

Fig.3

Fig.4

CND CONNECTOR

A

BATTERY PWB

 THE CAUTIONS ON BATTERY EXCHANGE

Risk of explosion if battery is replaced by incorrect type. Dispose of used batteries according to the instructions.

1-10 (No.YA064)

< HOUR METER BLOCK >

RESET HOUR METER (X1h) : 00000

ENTER: EXIT:

MENU

Fig.5

SECTION 3

DISASSEMBLY

3.1 DISASSEMBLY PROCEDURE

• Prior to assembly/disassembly procedure of the set, be sure to disconnect the power cord from the wall outlet.

• Perform the following procedures on a flat and strong place.

3.1.1 REMOVING THE AV TERMINAL (Fig.1)

(1) Disconnect the power cord from the wall outlet. (2) Remove the 2 screws [A]. (3) Remove the 2 screws [B]. (4) Lift the both ends of the AV TERMINAL slowly, and remove

the CN1001 PWB. Then, remove the AV TERMINAL.

3.1.2 REMOVING THE PC TERMINAL (Fig.1)

• Remove the AV TERMINAL. (1) Remove the 2 screws [C]. (2) Remove the 2 screws [D]. (3) Remove the 2 screws [E]. (4) Lift the both ends of the PC TERMINAL slowly, and remove

the CN1003 the MAIN PWB. Then, remove the PC TERMINAL.

3.1.3 REMOVING THE AV TERMINAL PWB (Fig.2)

[Only GM-V42S, GM-V42UB and GM-V42UG]

• Remove the AV TERMINAL. (1) Remove the 12 screws [F]. (2) Remove the AV TERMINAL PWB.

3.1.4 REMOVING THE PC TERMINAL PWB (Fig.2)

• Remove the AV TERMINAL.

• Remove the PC TERMINAL. (1) Remove the 4 screws [G]. (2) Remove the 4 screws [H] with a box wrench. (3) Remove the AV TERMINAL PWB.

/CN1002 connectors connected to the MAIN

/CN1004/CN1005 connectors connected to

PC TERMINAL PWB

AV TERMINAL PWB

A

B

Fig.1

AV TERMINAL

C

CN1002

CN1001

H

D

PC TERMINAL

E

CN1005 CN1004 CN1003

G

3.1.5 REMOVING THE BATTERY PWB (Fig.3)

• Remove the AV TERMINAL. (1) Remove the CND (2) Remove the 1 screw [I]. (3) Pull the BATTERY PWB toward you, and remove it.

connector.

CND CONNECTOR

I

BATTERY PWB

A

F

Fig.2

AV TERMINAL

B

Fig.3

(No.YA064)1-11

3.1.6 REMOVING THE FRONT PANEL (Fig.4)

• Remove the optional parts such as cooling fan if they are attached to the rear side of the main body.

• Place the main body with its screen side looking upward. (1) Remove the 3 screws [J]. (2) Lift the underside of the FRONT PANEL slowly, and

remove the tapes fixing the top part of the FRONT PANEL.

(3) Remove the FRONT PANEL.

3.1.7 REMOVING THE LED PWB (Fig.5)

• Remove the FRONT PANEL. (1) Remove the 2 screws [K]. (2) Remove the CNX (3) Remove the LED PWB.

connector.

CNX

K

LED PWB

Fig.4

M

J

CONTROL PWB

CNT

FRONT PANEL

CONTROL

PANEL

L

3.1.8 REMOVING THE CONTROL PWB (Fig.6)

• Remove the FRONT PANEL. (1) Remove the 2 screws [L]. (2) Remove the 3 screws [M]. (3) Remove the CNT (4) Remove the CONTROL PWB.

connector.

Surface

Fig.5

N O

REAR PANEL

1-12 (No.YA064)

Fig.6

3.1.9 REMOVING THE REAR COVER (Fig.7)

• Remove the AV TERMINAL.

• Remove the PC TERMINAL. (1) Remove the 21 screws [N]. (2) Remove the 1 screw [O]. (3) Lift the REAR COVER slowly, and remove it.

3.1.10 REMOVING THE BACK FRAME (LEFT/RIGHT) (Fig.7)

• Remove the AV TERMINAL.

• Remove the PC TERMINAL.

• Remove the REAR COVER. (1) Remove the 4 screws [P]. (2) Remove the 4 screws [Q]. (3) Lift the BACK FRAME, and remove it. (4) Remove the BACK FRAME on the other side in the same

way.

3.1.11 REMOVING THE SPEAKER / SPEAKER BRACKET (Fig.8)

• Remove the AV TERMINAL.

• Remove the PC TERMINAL.

• Remove the REAR COVER. (1) Remove the speaker cord. (2) Remove the 2 screws [R]. (3) Remove the SPEAKER. (4) Remove the SPEAKER on the other side in the same way. (5) Remove the clamp fixing the filter from the SPEAKER

BRACKET. (6) Remove the 2 screws [S]. (7) Remove the SPEAKER BRACKET. (8) Remove the SPEAKER BRACKET on the other side in the

same way.

P

BACK FRAME

Q

CNV CONNECTOR

T

TEMP. SENSOR PWB

Q P

Fig.7

SPEAKER

CLAMP

+

R

+

S

L

3.1.12 REMOVING THE TEMP. SENSOR PWB (Fig.8)

• Remove the AV TERMINAL.

• Remove the PC TERMINAL.

• Remove the REAR COVER. (1) Remove the CNV

connector on the TEMP. SENSOR PWB. (2) Remove the screw [T]. (3) Remove the TEMP. SENSOR PWB.

SPEAKER BRACKET

Fig.8

(No.YA064)1-13

3.1.13 REMOVING THE SPEAKER TERMINAL PWB (Fig.9)

• Remove the AV TERMINAL.

• Remove the PC TERMINAL.

• Remove the REAR COVER.

• Remove the BACK FRAME. (1) Remove the 3 screws [U], 2 screws [V], and 1 screw [W]. (2) Remove the SPEAKER TERMINAL BRACKET. (3) Lift the SPEAKER TERMINAL PWB, and remove the

CN6006

connector. (4) Remove the speaker cord connected to the SPEAKER. (5) Remove the speaker cord from each clamp. (6) Remove the SPEAKER TERMINAL PWB.

3.1.14 REMOVING THE AUDIO PWB (Fig.9)

• Remove the AV TERMINAL.

• Remove the PC TERMINAL.

• Remove the REAR COVER.

• Remove the BACK FRAME.

• Remove the SPEAKER TERMINAL BRACKET.

• Remove the SPEAKER TERMINAL PWB. (1) Remove the 1 screw [X]. (2) Remove the cords connected to the CNF

/CNA connectors

connected to the sound board from each clamp. (3) Remove the CNA (4) Disconnect the CN9004

connector on the MAIN PWB.

connector on the VIDEO SMPS

PWB. (5) Remove the AUDIO PWB.

VIDEO SMPS PWB

CN9004

CNF

CNA

CN6006

U

W

V

SPEAKER TERMINAL BRACKET

SPEAKER TERMINAL PWB

R

X

AUDIO PWB

L

F

1-14 (No.YA064)

CNA

MAIN PWB

Fig.9

3.1.15 REMOVING THE LINE FILTER PWB (Fig.10)

• Remove the AV TERMINAL.

• Remove the PC TERMINAL.

• Remove the REAR COVER.

• Remove the BACK FRAME. (1) Remove 1 screw [Y]. (2) Remove the noise filter from the clamp fixed to the SHIELD

COVER. (3) Remove the 4 screws [Z]. (4) Remove the SHIELD COVER. (5) Remove the CN8001

connector on the SMPS PWB. (6) Remove the 3 screws [a] fixing the LINE FILTER PWB. (7) Remove the LINE FILTER PWB.

3.1.16 REMOVING THE DIGITAL PWB (Fig.11)

• Remove the AV TERMINAL.

• Remove the PC TERMINAL.

• Remove the REAR COVER. (1) Lift the DIGITAL PWB SHIELD COVER, and remove it. (2) Remove the CNX

/CNV/CNQ/CND/CNT connectors. (3) Remove the 4 screws [b]. (4) Turn the DIGITAL PWB upside down, and remove the

CN2201

/CNJ/CNK connectors.

(5) Remove the DIGITAL PWB.

SHIELD COVER

CN8001

SMPS PWB

DIGITAL PWB

SHIELD COVER

CNJ

a

Z

LINE FILTER PWB

NOISE FILTER

#%

Y

#%

Fig.10

CNX

CNK

b

DIGITAL

PWB

CN201

CNQ

CND

CNT

CHASSIS BASE

E

Fig.11

(No.YA064)1-15

3.1.17 REMOVING THE MAIN PWB (Fig.12)

• Remove the AV TERMINAL.

• Remove the PC TERMINAL.

• Remove the REAR COVER.

• Remove the DIGITAL PWB SHIELD COVER.

• Remove the DIGITAL PWB. (1) Remove the CNA (2) Remove the 5 screws [c]. (3) Remove the MAIN PWB.

/CNE connectors.

MAIN PWB

CNE

CHASSIS

BASE

c

CNA

3.1.18 REMOVING THE CHASSIS BASE (Fig.13)

The CHASSIS BASE can be removed without removing the MAIN PWB, DIGITAL PWB, LINE FILTER PWB, AUDIO PWB, and BATTERY PWB from the CHASSIS BASE.

• Remove the AV TERMINAL.

• Remove the PC TERMINAL.

• Remove the REAR COVER.

• Remove the BACK FRAME (right).

• Remove the SPEAKER TERMINAL BRACKET.

• Remove the SPEAKER TERMINAL PWB. (1) Remove the CN9004

PWB. (2) Remove the cords from clamps. (3) Remove the CNX

DIGITAL PWB. (4) Remove the CNE (5) Remove the 4 screws [d], 2 screws [e], and 2 screws [f]. (6) Lift the CHASSIS BASE, and remove the LA03 connector

on the LOGIC-MAIN PWB. (7) Remove the CHASSIS BASE.

3.1.19 REMOVING THE PDP (PANEL) UNIT (Fig.13)

• Remove the AV TERMINAL.

• Remove the PC TERMINAL.

• Remove the REAR COVER.

• Remove the BACK FRAME (right).

• Remove the SPEAKER TERMINAL BRACKET.

• Remove the SPEAKER TERMINAL PWB.

• Remove the CHASSIS BASE. (1) Holding BACK FRAME SPACER, Lift the PDP upright and

remove it.

NOTE:

• When you remove the PDP (PANEL) UNIT, be careful not to

give a shock to the PDP (PANEL) UNIT enough. Two or more people are required to remove the PDP (PANEL) UNIT.

• Do not touch the front side (glass) of the PDP with your

fingers.

/CN8001 connectors on the SMPS

/CNV/CNQ/CNT connectors on the

connector on the MAIN PWB.

CNQ

e

CNE

SMPS PWB

CN9004

BLACK FLAME SPACER

CNT

LA03

Fig.12

d

CHASSIS BASE

CNV

CNX

f

BLACK FLAME SPACER

CN8001

LOGIC-MAIN PWB

Fig.13

1-16 (No.YA064)

3.1.20 DISASSEMBLY PDP UNIT

3.1.20.1 REMOVING THE SMPS PWB

• Remove the REAR COVER. (1) Remove the CN8007

CN8009

(2) Remove the 8 screws [g]. (3) Remove the SMPS PWB.

3.1.20.2 REMOVING THE X-MAIN PWB

• Removing the REAR COVER. (1) Remove the CN4001

connectors on the X-MAIN PWB. (2) Remove the 8 screws [h]. (3) Remove the X-MAIN PWB.

3.1.20.3 REMOVING THE Y-BUF-U PWB

• Remove the REAR COVER. (1) Remove the CN5401

connectors on the Y-BUF-U PWB. (2) Remove the 5 screws [I]. (3) Lift the Y-BUF-U PWB slightly, and remove the CN5404

CN5405 connectors on the Y-BUF-U PWB.

(4) Remove the Y-BUF-U PWB.

3.1.20.4 REMOVING THE Y-BUF-L PWB

• Remove the REAR COVER. (1) Remove the CN5501

connectors on the Y-BUF-L PWB. (2) Remove the 5 screws [j]. (3) Lift the Y-BUF-L PWB slightly, and remove the CN5504/

CN5505

(4) Remove the Y-BUF-L PWB.

3.1.20.5 REMOVING THE Y-MAIN PWB

• Remove the REAR COVER.

• Remove the CHASSIS BASE.

• Remove the Y-BUF-U PWB.

• Remove the Y-BUF-L PWB. (1) Remove the CN5001

PWB. (2) Remove the 7 screws [k]. (3) Remove the Y-MAIN PWB.

/CN8002 connectors on the SMPS PWB.

connectors on the Y-BUF-L PWB.

/CN8008/CN8004/BUFFER/CN8003/

/CN4002/CN4003/CN4004/CN4005

/CN5402/CN5403/CN5406

/CN5502/CN5503/CN5506

/CN5008 connectors on the Y-MAIN

3.1.20.6 REMOVING THE LOGIC-MAIN PWB

• Remove the REAR COVER.

• Remove the CHASSIS BASE. (1) Remove the CN101

connectors on the LOGIC-MAIN PWB. (2) Remove the 6 screws [l]. (3) Remove the LOGIC-MAIN PWB.

3.1.20.7 REMOVING THE E-BUF PWB

• Remove the REAR COVER.

• Remove the BACK FRAME.

• Remove the CHASSIS BASE.

• Remove the SPEAKER BRACKET (left). (1) Remove the EC1

connectors on the E-BUF PWB. (2) Remove the 6 screws [m]. (3) Remove the E-BUF PWB.

3.1.20.8 REMOVING THE F-BUF PWB

/

• Remove the REAR COVER.

• Remove the BACK FRAME.

• Remove the CHASSIS BASE. (1) Remove the FC4

BUF PWB. (2) Remove thr 4 screws [n]. (3) Remove the F-BUF PWB.

3.1.20.9 REMOVING THE G-BUF PWB

• Remove the REAR COVER.

• Remove the BACK FRAME.

• Remove the CHASSIS BASE.

• Remove the SPEAKER BRACKET (right). (1) Remove the GC5

the G-BUF PWB. (2) Remove the 6 screws [o]. (3) Remove the G-BUF PWB.

3.1.20.10 REMOVING THE VIDEO SMPS PWB

• Remove the REAR COVER. (1) Remove the CN9001

CN9007

(2) Remove the 4 screws [p]. (3) Remove the VIDEO SMPS PWB.

connectors on the VIDEO SMPS PWB.

/CN201/CN401/CN402/CN403/CN803

/EC2/EC3/CN401/CN806/EF1

/CN402/FE1/FG1 connectors on the F-

/GC6/GC7/CN403/GF1 connectors on

/CN9002/CN9004/CN9005/CN9006/

(No.YA064)1-17

CN5008

CN5404

CN5406

CN5405

CN5505

CN5506

CN5504

CN5001

CN5401

CN5402

CN5403

CN5501

CN5502

CN5503

CN9005

CN9006

CN9001

CN9007

CN9002

CN9004

CN8003

BUFFER

CN8004

CN8007

CN8008

CN8009 CN8002

CN201

CN803

CN101

CN401

CN402

CN403

CN4001 CN4003

CN4004

CN4002

CN4005

Y-BUF-U PWB

Y-BUF-L PWB

EC1

Y-MAIN PWB

i

EC2 EC3

CN806 CN401 CN402 CN403

EF1

FC4 FC4

FE1

GC5 GC6 GC7

GF1

SMPS PWBVIDEO SMPS PWB

k

p

g

X-MAIN PWB

l h

1-18 (No.YA064)

j

m

n

o

E-BUF PWB G-BUF PWBF-BUF PWB

LOGIC-MAIN PWB

Fig.14

3.2 REPLACEMENT OF MEMORY ICs

3.2.1 MEMORY IC

This model uses memory IC. In the memory IC is memorized data for correctly operating the video and drive circuits. When replacing the memory IC, be sure to use IC written with the initial values of data.

3.2.2 PROCEDURE FOR REPLACING MEMORY IC

(1) Power off

Switch the power off and unplug the power plug from the wall outlet.

(2) Replace IC

Be sure to use memory IC written with the initial data values.

(3) Power on

Connect the power plug into the wall outlet and turn the power on.

3.2.3 PROCEDURE FOR SET-UP MENU

(1) Press the [MENU / EXIT] key and the [VOLUME-] key

simultaneously. (2) The SET-UP MENU screen (Fig. 1) will be displayed. (3) Check the setting value of the SET-UP MENU table. (Refer

to the next page.) (4) If the value is different, select the setting item with the

SELECT [/] key, and set the correct value with the

ADJUST [/] key. (5) Press the [MENU / EXIT] key, and return to the normal

screen.

3.2.4 PROCEDURE FOR reset OR all reset

(1) The SET-UP MENU is displayed. (2) Select "reset" or "all reset" item with SELECT [/] key of

remote control unit. (3) Press ENTER [] key, and the "reset" (or all reset) menu is

displayed (Fig. 2). (4) Press ENTER [] key to "reset" the standard settings.

< SET-UP MENU >

STATUS DISPLAY CONTROL LOCK REMOTE SWITCH HD SIGNAL MODE WHITE BALANCE TIMER

ADJUST: SELECT: EXIT:

< SET-UP MENU > 2/2

PIXEL SHIFT POWER SAVE COLOR-REVERSE REFRESH reset all reset HOUR METER x100h MODEL NAME : GM-V42

ADJUST: SELECT: EXIT:

: ON : OFF : MODE1 : 1080i

: OFF : OFF : OFF : OFF

: 000

1/2

MENU

SET-UP MENUscreen

When select the [reset or all reset] change to [ENTER : ] mode.

Fig.1

or <reset>

< all reset >

Are you sure

"YES" then Key. "NO" then Key.

MENU

[reset] / [all reset]

Fig.2

REMOTE CONTROL UNIT KEY ASSIGNMENT

MENU/EXIT

key

RM-C579 REMOTE CONTROL UNIT

POWER

OFF ON

DISPLAY

INPUT SELECT

A

VIDEO

MUTING

MENU/EXIT

VOLUME

ASPECT

COMPO.

/(RGB B)

RGB AB

VOLUME key

(-/+)

SELECT key

( )

ENTER key ( )

ADJUST key

( )

(No.YA064)1-19

 INITIAL SETTING OF FACTORY SHIPPING

Setting item Setting value Setting item Setting value

POWER OFF VOLUME 10

INPUT SELECT VIDEO A

MAIN MENU

PICTURE ADJ. CONTRAST 10 SIZE/POSITION ADJ. V POSITION 00

BRIGHT 00 DOT CLOCK (RGB only) 00

CHROMA 00 CLOCK PHASE (RGB only) 00

PHASE 00 FUNCTION SELECT COLOR TEMP HIGH

SHARPNESS 00 ASPECT REGULAR

SIZE/POSITION ADJ. H SIZE 00 SIGNAL MODE AUTO

H POSITION 00 RGB / COMP. COMP.

V SIZE 00 SYNC TERM HIGH

SETUP MENU

STATUS DISPLAY ON REMOTE SWITCH MODE1

CONTROL LOCK OFF HD SIGNAL MODE 1080i

WHITE BALNCE HIGH R GAIN Set MAX at

G GAIN START SET OFF

B GAIN START TIME - - : - -

LOW R GAIN Set MAX at

G GAIN END TIME - - : - -

B GAIN REFRESH REFRESH OFF

TIMER PRESENT TIME - - : - - START SET OFF

POWER-ON SET OFF START TIME - - : - -

POWER-ON TIME - - : - - END SET OFF

POWER-OFF SET OFF END TIME - - : - -

POWER-OFF TIME - - : - - MODEL NAME GM-V42

PIXEL SHIFT OFF

POWER SAVE OFF

least one item. (other is 0)

COLOR-REVERSE COLOR-REVERSE OFF

END SET OFF

 SERVICE SETTING ITEMS

Setting item Contents Setting item Contents

VCO ADJUST Video decorder VCO adjustment SIGNAL BLOCK Signal circuit adjustment

WHITE BALANCE BLOCK WHITE BALANCE adjustment DEVICE INITIAL VALUE Initial setting of DEVICE

CPU BLOCK Setting of CPU DIAGNOSIS BLOCK DIAGNOSIS function

SIZE/POSITION BLOCK SIZE/POSITION adjustment HOUR METER BLOCK HOUR METER function

H. POSITION BLOCK H. POSITION adjustment ENHANCER BLOCK Sharpness circuit adjustment

PANEL BLOCK Setting of PDP (panel)

1-20 (No.YA064)

3.3 REPLACEMENT OF CHIP COMPONENT

3.3.1 CAUTIONS

(1) Avoid heating for more than 3 seconds. (2) Do not rub the electrodes and the resist parts of the pattern. (3) When removing a chip part, melt the solder adequately. (4) Do not reuse a chip part after removing it.

3.3.2 SOLDERING IRON

(1) Use a high insulation soldering iron with a thin pointed end of it. (2) A 30w soldering iron is recommended for easily removing parts.

3.3.3 REPLACEMENT STEPS

1. How to remove Chip parts

2. How to install Chip parts

[Resistors, capacitors, etc.]

(1) As shown in the figure, push the part with tweezers and

alternately melt the solder at each end.

(2) Shift with the tweezers and remove the chip part.

[Transistors, diodes, variable resistors, etc.]

(1) Apply extra solder to each lead.

SOLDER

[Resistors, capacitors, etc.]

(1) Apply solder to the pattern as indicated in the figure.

(2) Grasp the chip part with tweezers and place it on the

solder. Then heat and melt the solder at both ends of the chip part.

[Transistors, diodes, variable resistors, etc.]

(1) Apply solder to the pattern as indicated in the figure. (2) Grasp the chip part with tweezers and place it on the

solder.

(3) First solder lead A as indicated in the figure.

(2) As shown in the figure, push the part with tweezers and

alternately melt the solder at each lead. Shift and remove

the chip part.

NOTE :

After removing the part, remove remaining solder from the pattern.

A

B

C

(4) Then solder leads B and C.

A

B

C

(No.YA064)1-21

SECTION 4

ADJUSTMENT

4.1 BEFORE ADJUSTMENT

(1) There are 2 ways of adjusting this monitor : One is with the

REMOTE CONTROL UNIT and the other is the conventional method using adjustment parts and components.

(2) The setting (adjustment) using the REMOTE CONTROL

UNIT is made on the basis of the initial setting values. The setting values which adjust the screen to the optimum condition can be different from the initial setting values.

(3) Make sure that connection is correctly made to AC power

source.

(4) Turn on the power of the Plasma display monitor and

measuring instrument for warming up for at least 30 minutes before starting adjustment.

(5) If the input signal is not specified, use the most appropriate

signal for adjustment.

(6) Never touch parts (such as variable resistors, transformers

and condensers) not shown in the adjustment items of this service adjustment.

4.2 MEASURING INSTRUMENT AND TOOLS

• DC voltmeter (or digital voltmeter)

• Oscilloscope

• Colour analyzer (colour temperature meter)

• Signal generator

- Colour bar : PAL / SECAM / NTSC

- Whale black pattern : 480i, 1080i

- Lamp pattern :

NTSC / 480i / 1080i / VGA640 × 480 dots (H: 31.5kHz, V: 60Hz)

/ RGB 15k (H: 15.73kHz, V: 59.94Hz)

- Window pattern :

NTSC /480i / 1080i / VGA640 × 480 dots (H: 31.5kHz, V: 60Hz)

/ RGB 15k (H: 15.73kHz, V: 59.94Hz)

- Gray scall pattern :

NTSC/480i / 1080i / VGA640 × 480 dots (H: 31.5kHz, V: 60Hz)

/ RGB 15k (H: 15.73kHz, V: 59.94Hz)

• Remote control unit

4.3 PROCEDURE FOR SERVICE MODE

4.3.1 HOW TO ENTER THE SERVICE MODE

(1) Press the [MENU] key, and SELECT [] key

simultaneously (Fig. 1).

(2) The " " mark is appears at the center of the screen (Fig.

2).

(3) While " " mark is appears, press the [MENU] key and

[VOL-] key simultaneously.

(4) The word "PLEASE DON'T TOUCH !" (Fig.3) will be

display on the screen center.

(5) While the words of "PLEASE DON'T TOUCH !" are display

as shown in Fig. 3.

(6) Press the SELECT [] key, SERVICE MODE will be

display as shown in Fig. 4.

4.3.2 SELECT & ADJUSTMENT OF SERVICE MODE ITEM

While the SERVICE MODE is displayed.

(1) Press the up [/] select key to white balance block item. (2) After selecting the item, press ENTER [] key. (3) The adjustment menu mode is displayed. (4) Press the ADJUST [/] key to change the setting value. (5) Press [MENU / EXIT] key to display the original menu. (6) Perform in the same manner for others SERVICE MODE

ITEM.

Note :

When the adjustment is made at SERVICE MODE, the changed data is memorized in a memory simultaneously with the change.

Fig.1

Fig.2

PLEASE, DON'T TOUCH!

Fig.3

VCO ADJUST WHITE BALANCE BLOCK CPU BLOCK SIZE/POSITION BLOCK H POSITION BLOCK PANEL BLOCK SIGNAL BLOCK DEVICE INITIAL VALUE

ENTER: SELECT: EXIT:

DIAGNOSIS BLOCK UPDATE CPU PROGRAM HOUR METER BLOCK ENHANCER BLOCK

ENTER: SELECT: EXIT:

Fig.4

[1/2]

MENU

[2/2]

MENU

1-22 (No.YA064)

4.4 COMPOSITION OF SERVICE MENU SCREEN

MAIN MENU

W(A01)

WHITE BALANCE BLOCK

adjustment item screen

C(A01)

CPU BLOCK

adjustment item screen

VCO ADJUST WHITE BALANCE BLOCK CPU BLOCK SIZE/POSITION BLOCK H POSITION BLOCK PANEL BLOCK SIGNAL BLOCK DEVICE INITIAL VALUE

ENTER: SELECT: EXIT:

< VCO ADJUST PROGRAM >

Are you sure ?

"YES" then Key. "NO" then Key.

MENU

< WHITE BALANCE BLOCK >

WA:RGB PS HIGH WB:RGB PC LOW WC:VIDEO HIGH WD:VIDEO LOW WE:COMPO. 15k HIGH WF:COMPO. 15k LOW WG:COMPO. HIGH WH:COMPO. LOW

ENTER: SELECT: EXIT:

WHITE BALANCE BLOCK

adjustment item select screen

< CPU BLOCK >

CA:PANORAMA DATA CB:SIGNAL RANGE CC:SIZE/POSI. RANGE CD:FRQENCY DATA CE:SYSTEM CONSTANT CF:TEMP SENCOR DATA CG:APS CONTROL DATA CH:TEST MODE

ENTER: SELECT: EXIT:

CPU BLOCK

adjustment item select screen

< SIZE/POSITION BLOCK >

DA:VIDEO-60Hz (REGULAR) DB:VIDEO-60Hz (FULL) DC:VIDEO-60Hz (ZOOM) DD:VIDEO-60Hz (PANORA.) DE:VIDEO-50Hz (REGULAR) DF:VIDEO-50Hz (FULL) DG:VIDEO-50Hz (ZOOM) DH:VIDEO-50Hz (PANORA.)

ENTER: SELECT: EXIT:

< H POSITION BLOCK >

PA:VIDEO PB:Y/C PC:COMPO. PD:RGB

ENTER: SELECT: EXIT:

MENU

[2/2]

MENU

Are you sure ?

"YES" then Key. "NO" then Key.

MENU

DIAGNOSIS BLOCK

< CLEAR >

MENU

Flashing 5 sec.

[1/2]

MENU

DIAGNOSIS BLOCK UPDATE CPU PROGRAM HOUR METER BLOCK ENHANCER BLOCK

ENTER: SELECT: EXIT:

< DIAGNOSIS BLOCK >

CLEAR I2C SIGNAL BUS I2C ROM BUS POWER TEMP. OVER TEMP. OVER [9Eh] TEMP. OVER [9Ch]

ENTER: EXIT:

< DIAGNOSIS BLOCK >

CLEAR I2C SIGNAL BUS I2C ROM BUS POWER TEMP. OVER TEMP. OVER [9Eh] TEMP. OVER [9Ch]

ENTER: EXIT:

< UPDATE CPU PROGRAM >

Are you sure ?

"YES" then Key. "NO" then Key.

Necessity ! : PC, cable & terminal software

CURRENT Ver. 1.02

< HOUR METER BLOCK >

RESET HOUR METER (X1h) : *****

ENTER: EXIT:

< PANEL BLOCK >

BA:VIDEO BB:PC

ENTER: SELECT: EXIT:

< SIGNAL BLOCK >

SA:VIDEO -NTSC SB:VIDEO -PAL SC:VIDEO -SECAM SD:VIDEO -NTSC4.43 SE:VIDEO -PALM SF:VIDEO -PALN SG:VIDEO -PAL-60 SH:Y/C -NTSC

ENTER: SELECT: EXIT:

< DEVICE INITIAL VALUE >

IA:VPC3230D IB:CXA3506R IC:TA1318 ID:PEMBRANDT-I IE:PDP I/F IF:PDP MODULE IG:UPD64083GF

ENTER: SELECT: EXIT:

MENU

< HOUR METER BLOCK >

RESET HOUR METER (X1h) : 00000

ENTER: EXIT:

< ENHANCER BLOCK >

EA:SHARPNESS A=-3 EB:SHARPNESS A=-2 EC:SHARPNESS A=-1 ED:SHARPNESS A= 0 EE:SHARPNESS A=+1 EF:SHARPNESS A=+2 EG:SHARPNESS A=+3 EH:SHARPNESS A=+4

ENTER: SELECT: EXIT:

< RESET HOUR METER >

! Are you sure ?

"YES" then Key. "NO" then Key.

MENU

(No.YA064)1-23

4.5 INITIAL SETTING VALUE OF THE SERVICE MODE

 WHITE BALANCE BLOCK

Setting No. Setting item

WA : RGB PC HIGH

W(A01) DRIVE (R) 255 W(A02) DRIVE (G) 255 W(A03) DRIVE (B) 255 W(A04) CUT OFF (R) -001 W(A05) CUT OFF (G) -001 W(A06) CUT OFF (B) -001 W(A07) BRIGHT 000 W(A08) A-D GAIN (R) 128 W(A09) A-D GAIN (G) 128 W(A10) A-D GAIN (B) 128 W(A11) A-D OFFSET (R) 000 W(A12) A-D OFFSET (G) 000 W(A13) A-D OFFSET (B) 000

WB : RGB PC LOW

W(B01) DRIVE (R) 255 W(B02) DRIVE (G) 255 W(B03) DRIVE (B) 200 W(B04) CUT OFF (R) 000 W(B05) CUT OFF (G) 000 W(B06) CUT OFF (B) 000 W(B07) BRIGHT 000 W(B08) A-D GAIN (R) 000 W(B09) A-D GAIN (G) 000 W(B10) A-D GAIN (B) 000 W(B11) A-D OFFSET (R) 000 W(B12) A-D OFFSET (G) 000 W(B13) A-D OFFSET (B) 000

WC : VIDEO HIGH

W(C01) DRIVE (R) 255 W(C02) DRIVE (G) 255 W(C03) DRIVE (B) 255 W(C04) CUT OFF (R) -003 W(C05) CUT OFF (G) -004 W(C06) CUT OFF (B) -003 W(C07) BRIGHT -011

WD : VIDEO LOW

W(D01) DRIVE (R) 255 W(D02) DRIVE (G) 255 W(D03) DRIVE (B) 200 W(D04) CUT OFF (R) 000 W(D05) CUT OFF (G) 000 W(D06) CUT OFF (B) 000 W(D07) BRIGHT 000

WE : COMPO. 15k HIGH

W(E01) DRIVE (R) 255 W(E02) DRIVE (G) 255 W(E03) DRIVE (B) 255 W(E04) CUT OFF (R) -002 W(E05) CUT OFF (G) -004 W(E06) CUT OFF (B) -002 W(E07) BRIGHT 000 W(E08) A-D GAIN (R) 128

1-24 (No.YA064)

Setting

value

Setting No. Setting item

W(E09) A-D GAIN (G) 128 W(E10) A-D GAIN (B) 128 W(E11) A-D OFFSET (R) -002 W(E12) A-D OFFSET (G) 000 W(E13) A-D OFFSET (B) -002

WF : COMPO. 15k LOW

W(F01) DRIVE (R) 255 W(F02) DRIVE (G) 255 W(F03) DRIVE (B) 200 W(F04) CUT OFF (R) 000 W(F05) CUT OFF (G) 000 W(F06) CUT OFF (B) 000 W(F07) BRIGHT 000 W(F08) A-D GAIN (R) 000 W(F09) A-D GAIN (G) 000 W(F10) A-D GAIN (B) 000 W(F11) A-D OFFSET (R) 000 W(F12) A-D OFFSET (G) 000 W(F13) A-D OFFSET (B) 000

WG : COMPO. HIGH

W(G01) DRIVE (R) 255 W(G02) DRIVE (G) 255 W(G03) DRIVE (B) 255 W(G04) CUT OFF (R) -003 W(G05) CUT OFF (G) -004 W(G06) CUT OFF (B) -003 W(G07) BRIGHT 000 W(G08) A-D GAIN (R) 128 W(G09) A-D GAIN (G) 128 W(G10) A-D GAIN (B) 128 W(G11) A-D OFFSET (R) -002 W(G12) A-D OFFSET (G) 000 W(G13) A-D OFFSET (B) -002

WH : COMPO. LOW

W(H01) DRIVE (R) 255 W(H02) DRIVE (G) 255 W(H03) DRIVE (B) 200 W(H04) CUT OFF (R) 000 W(H05) CUT OFF (G) 000 W(H06) CUT OFF (B) 000 W(H07) BRIGHT 000 W(H08) A-D GAIN (R) 000 W(H09) A-D GAIN (G) 000 W(H10) A-D GAIN (B) 000 W(H11) A-D OFFSET (R) 000 W(H12) A-D OFFSET (G) 000 W(H13) A-D OFFSET (B) 000

Setting

value

Setting No. Setting item

WI : RGB 15k HIGH

W(I01) DRIVE (R) 255 W(I02) DRIVE (G) 255 W(I03) DRIVE (B) 255 W(I04) CUT OFF (R) -001 W(I05) CUT OFF (G) -001 W(I06) CUT OFF (B) -001 W(I07) BRIGHT 000 W(I08) A-D GAIN (R) 125 W(I09) A-D GAIN (G) 128 W(I10) A-D GAIN (B) 128 W(I11) A-D OFFSET (R) 000 W(I12) A-D OFFSET (G) 000 W(I13) A-D OFFSET (B) 000

Setting

value

Setting No. Setting item

WJ : RGB 15k LOW

W(J01) DRIVE (R) 255 W(J02) DRIVE (G) 200 W(J03) DRIVE (B) 198 W(J04) CUT OFF (R) 000 W(J05) CUT OFF (G) 000 W(J06) CUT OFF (B) 000 W(J07) BRIGHT 000 W(J08) A-D GAIN (R) 000 W(J09) A-D GAIN (G) 000 W(J10) A-D GAIN (B) 000 W(J11) A-D OFFSET (R) 000 W(J12) A-D OFFSET (G) 000 W(J13) A-D OFFSET (B) 000

Setting

value

(No.YA064)1-25

 CPU BLOCK

Setting No. Setting item

CA : PANORAMA DATA

C(A01) INPUT_PIXELS 086 C(A02) OUTPUT_PIXELS 107 C(A03) NL_START 052 C(A04) NL_END 055 C(A05) RATIO_CENTER 076 C(A06) RATIO_SIDES 101 C(A07) Not use 000 C(A08) Not use 000 C(A09) Not use 000 C(A10) Not use 000

CB : SIGNAL RANGE

C(B01) CONTRAST MIN -044 C(B02) CONTRAST MAX +020 C(B03) BRIGHT MIN -012 C(B04) BRIGHT MAX +012 C(B05) CROMA MIN -071 C(B06) CROMA MAX +045 C(B07) FHASE MIN ----C(B08) FHASE MAX ----C(B09) V BRI_GAIN COMP 255 C(B10) G BRI_GAIN COMP 255 C(B11) R GAIN MIN 000 C(B12) R GAIN MAX 255 C(B13) G GAIN MIN 000 C(B14) G GAIN MAX 255 C(B15) B GAIN MIN 000 C(B16) B GAIN MAX 255

CC : SIZE/POSI. RANGE

C(C01) H_POS_MIN -060 C(C02) H_POS_MAX 060 C(C03) V_POS_MIN -030 C(C04) V_POS_MAX 030 C(C05) H_SIZE_MIN -100 C(C06) H_SIZE_MAX 100 C(C07) V_SIZE_MIN -100 C(C08) V_SIZE_MAX 100 C(C09) DOT_CLK_MIN -010 C(C10) DOT_CLK_MAX 010 C(C11) CLK_PHASE_MIN -020 C(C12) CLK_PHASE_MAX 020 C(C13) MARGIN_POS_X -006 C(C14) Not use 000 C(C15) Not use 000 C(C16) H_POS_MIN -055 C(C17) H_POS_MAX 055 C(C18) V_POS_MIN -030 C(C19) V_POS_MAX 030 C(C20) H_SIZE_MIN -060 C(C21) H_SIZE_MAX 060 C(C22) V_SIZE_MIN -060 C(C23) V_SIZE_MAX 060 C(C24) INPUT_X_V60_L 208 C(C25) INPUT_X_V60_H 002

Setting

value

Setting No. Setting item

C(C26) INPUT_Y_V60_L 229 C(C27) INPUT_Y_V60_H 001 C(C28) INPUT_X_V50_L 208 C(C29) INPUT_X_V50_H 002 C(C30) INPUT_Y_V50_L 068 C(C31) INPUT_Y_V50_H 002 C(C32) FREE_RUN 000 C(C33) DS_InX_MARGINE 003 C(C34) DS_OutX_MARGINE 002 C(C35) DS_InY_MARGINE 003 C(C36) DS_OutY_MARGINE 002 C(C37) M_OutX_MARGINE 002 C(C38) Not use 000 C(C39) Not use 000 C(C40) Not use 000 C(C41) Not use 000 C(C42) Not use 000 C(C43) Not use 000 C(C44) Not use 000 C(C45) Not use 000 C(C46) Not use 000 C(C47) Not use 000 C(C48) Not use 000 C(C49) Not use 000 C(C50) Not use 000 C(C51) Not use 000 C(C52) Not use 000

CD : FREQENCY DATA

C(D01) HORI FREQ ERROR 004 C(D02) VERT FREQ ERROR 001 C(D03) STATUS DELAY 050 C(D04) SIGNAL DETECT 010 C(D05) SIGNAL WAIT TIM 040 C(D06) SIGNAL WAIT TIM 000

CE : SYSTEM CONSTANT

C(E01) AREA 002 C(E02) POWER ON DELAY 031 C(E03) POWER ON DELAY 031 C(E04) MODEL No. 001 C(E05) REMOCON THROW 000 C(E06) TIME ERROR COMPENSATION +007 C(E07) VS_MUTE 001 C(E08) GOAL_PLC PW SELECT for 50Hz 000 C(E09) Not use 000 C(E10) Not use 000

Setting

value

1-26 (No.YA064)

Setting No. Setting item

CF : TEMP SENSOR DATA

C(F01) Y ALARM TEMP. : T1 068 C(F02) T1 OVER COUNT 060 C(F03) SHUT DOWN TEMP. : T2 120 C(F04) T2 OVER COUNT 060 C(F05) TEMP. ALARM DISPLAY ON/OFF 000 C(F06) R ALARM TEMP. T3 095 C(F07) T3 OVER COUNT 060 C(F08) T3 SHUT DOWN WAIT TIME 012 C(F09) APS CONT. START TEMP : 4 052 C(F10) Not use 000

CG : APS CONTROL DATA

C(G01) Is COMPENSATION 150 C(G02) Is STANDARD 150 C(G03) APS PANEL IN MOD 010 C(G04) LEVEL ADJ 255 C(G05) AGC ON/OFF 000 C(G06) AGC GAIN MAX 000 C(G07) STOP PLC SELECT : K1 032 C(G08) GOAL PLC (NORMAL) SELECT : n 000 C(G09) SAMPLING CYCLE SETTING 004 C(G10) STOPPER INTERVAL SETTING 020 C(G11) ANIMATION LUMINOSITY

COMPENSATION C(G12) GOAL PLC SELECT :K2 095 C(G13) SAVE1 LOW SETTING 045 C(G14) POWER CONT. INTERVAL(MAIN) 002 C(G15) POWER CONT. INTERVAL(SUB) 003 C(G16) POWER CONT. COEFFICIENT : K 028 C(G17) KX1 035 C(G18) KX2 065 C(G19) KX3 120

Setting

value

000

Setting No. Setting item

C(G20) KYmax0 005 C(G21) KYmax1 052 C(G22) KYmax2 100 C(G23) KYmax3 215 C(G24) KYmax4[7:0] 000 C(G25) KYmin0 010 C(G26) KYmin1 075 C(G27) KYmin2 141 C(G28) KYmin3 255 C(G29) KYmin4[7:0] 000 C(G30) KYmax4[11:8], KYmin[11:8] 017

CH : TEST MODE

C(H01) FPGA TEST MODE 000 C(H02) 480i MATRIX 000 C(H03) 480p MATRIX 000 C(H04) FREQ CHECK DISP 000 C(H05) APS CHECK DISP 000 C(H06) D TERM DET OFF 000 C(H07) VPC VERSION 000 C(H08) TEST PATTERN 000 C(H09) Not use 000 C(H10) Not use 000

CI : OTHER

C(I01) PIXEL SHIFT INTERVAL 001 C(I02) PIXEL SHIFT H POSI SHIFT 010 C(I03) PIXEL SHIFT V POSI SHIFT 006 C(I04) RS-232 BAUD 000 C(I05) B GAIN VALUE 195 C(I06) Not use 000 C(I07) Not use 000 C(I08) Not use 000 C(I09) Not use 000 C(I10) Not use 000

Setting

value

(No.YA064)1-27

 SIZE / POSITION BLOCK

Setting No. Setting item

DA : VIDEO-60Hz (REGULAR)

D(A01) FB COUNTER 1 172 D(A02) FB COUNTER 2 006 D(A03) VCO DIVIDE 002 D(A04) DELAY 032 D(A05) CHARGE_PUMP 018 D(A06) AMP MODE 001 D(A07) OUTPUT MODE 006 D(A08) OPLL_MDVI_L 229 D(A09) OPLL_MDVI_H 000 D(A10) OPLL_MDVI 255 D(A11) INPUT_ACT_LINE_START_L 012 D(A12) INPUT_ACT_LINE_START_H 000 D(A13) INPUT_ACT_LINE_L 200 D(A14) INPUT_ACT_LINE_H 001 D(A15) INPUT_ACT_PIXEL_START_L 022 D(A16) INPUT_ACT_PIXEL_START_H 000 D(A17) INPUT_ACT_PIXEL_L 158 D(A18) INPUT ACT_PIXEL_H 002 D(A19) Not use 000 D(A20) Not use 000 D(A21) WIN_X_MARGINE 128 D(A22) WIN_Y_MARGINE 128 D(A23) WIN_Y_POSI_L 001 D(A24) WIN_Y_POSI_H 000 D(A25) WIN_Y_SIZE_L 224 D(A26) WIN_Y_SIZE_H 001 D(A27) WIN_X_POSI_L 106 D(A28) WIN_X_POSI_H 000 D(A29) WIN_X_SIZE_L 128 D(A30) WIN_X_SIZE_H 002 D(A31) Not use 000 D(A32) Not use 000 D(A33) Not use 000 D(A34) Not use 000 D(A35) Not use 000 D(A36) Not use 000 D(A37) Not use 000 D(A38) COAST_ENABLE 000 D(A39) Not use 000 D(A40) INTERLACE 000 D(A41) Not use 000 D(A42) Not use 000 D(A43) Not use 000 D(A44) Not use 000 D(A45) Not use 000 D(A46) Not use 000 D(A47) Not use 000 D(A48) Not use 000 D(A49) Not use 000 D(A50) Not use 000 D(A51) Not use 000 D(A52) Not use 000

Setting

value

Setting No. Setting item

DB : VIDEO-60Hz (FULL)

D(B01) FB COUNTER 1 172 D(B02) FB COUNTER 2 006 D(B03) VCO DIVIDE 002 D(B04) DELAY 032 D(B05) CHARGE_PUMP 018 D(B06) AMP MODE 001 D(B07) OUTPUT MODE 006 D(B08) OPLL_MDVI_L 229 D(B09) OPLL_MDVI_H 000 D(B10) OPLL_MDVI 255 D(B11) INPUT_ACT_LINE_START_L 012 D(B12) INPUT_ACT_LINE_START_H 000 D(B13) INPUT_ACT_LINE_L 200 D(B14) INPUT_ACT_LINE_H 001 D(B15) INPUT_ACT_PIXEL_START_L 023 D(B16) INPUT_ACT_PIXEL_START_H 000 D(B17) INPUT_ACT_PIXEL_L 158 D(B18) INPUT ACT_PIXEL_H 002 D(B19) Not use 000 D(B20) Not use 000 D(B21) WIN_X_MARGINE 128 D(B22) WIN_Y_MARGINE 128 D(B23) WIN_Y_POSI_L 001 D(B24) WIN_Y_POSI_H 000 D(B25) WIN_Y_SIZE_L 224 D(B26) WIN_Y_SIZE_H 001 D(B27) WIN_X_POSI_L 001 D(B28) WIN_X_POSI_H 000 D(B29) WIN_X_SIZE_L 084 D(B30) WIN_X_SIZE_H 003 D(B31) Not use 000 D(B32) Not use 000 D(B33) Not use 000 D(B34) Not use 000 D(B35) Not use 000 D(B36) Not use 000 D(B37) Not use 000 D(B38) COAST_ENABLE 000 D(B39) Not use 000 D(B40) INTERLACE 000 D(B41) Not use 000 D(B42) Not use 000 D(B43) Not use 000 D(B44) Not use 000 D(B45) Not use 000 D(B46) Not use 000 D(B47) Not use 000 D(B48) Not use 000 D(B49) Not use 000 D(B50) Not use 000 D(B51) Not use 000 D(B52) Not use 000

Setting

value

1-28 (No.YA064)

Setting No. Setting item

DC : VIDEO-60Hz (ZOOM)

D(C01) FB COUNTER 1 172 D(C02) FB COUNTER 2 006 D(C03) VCO DIVIDE 002 D(C04) DELAY 032 D(C05) CHARGE_PUMP 018 D(C06) AMP MODE 001 D(C07) OUTPUT MODE 006 D(C08) OPLL_MDVI_L 229 D(C09) OPLL_MDVI_H 000 D(C10) OPLL_MDVI 255 D(C11) INPUT_ACT_LINE_START_L 069 D(C12) INPUT_ACT_LINE_START_H 000 D(C13) INPUT_ACT_LINE_L 087 D(C14) INPUT_ACT_LINE_H 001 D(C15) INPUT_ACT_PIXEL_START_L 023 D(C16) INPUT_ACT_PIXEL_START_H 000 D(C17) INPUT_ACT_PIXEL_L 158 D(C18) INPUT ACT_PIXEL_H 002 D(C19) Not use 000 D(C20) Not use 000 D(C21) WIN_X_MARGINE 128 D(C22) WIN_Y_MARGINE 128 D(C23) WIN_Y_POSI_L 001 D(C24) WIN_Y_POSI_H 000 D(C25) WIN_Y_SIZE_L 224 D(C26) WIN_Y_SIZE_H 001 D(C27) WIN_X_POSI_L 001 D(C28) WIN_X_POSI_H 000 D(C29) WIN_X_SIZE_L 084 D(C30) WIN_X_SIZE_H 003 D(C31) Not use 000 D(C32) Not use 000 D(C33) Not use 000 D(C34) Not use 000 D(C35) Not use 000 D(C36) Not use 000 D(C37) Not use 000 D(C38) COAST_ENABLE 000 D(C39) Not use 000 D(C40) INTERLACE 000 D(C41) Not use 000 D(C42) Not use 000 D(C43) Not use 000 D(C44) Not use 000 D(C45) Not use 000 D(C46) Not use 000 D(C47) Not use 000 D(C48) Not use 000 D(C49) Not use 000 D(C50) Not use 000 D(C51) Not use 000 D(C52) Not use 000

Setting

value

Setting No. Setting item

DD : VIDEO-60Hz (PANORA.)

D(D01) FB COUNTER 1 172 D(D02) FB COUNTER 2 006 D(D03) VCO DIVIDE 002 D(D04) DELAY 032 D(D05) CHARGE_PUMP 018 D(D06) AMP MODE 001 D(D07) OUTPUT MODE 006 D(D08) OPLL_MDVI_L 229 D(D09) OPLL_MDVI_H 000 D(D10) OPLL_MDVI 255 D(D11) INPUT_ACT_LINE_START_L 024 D(D12) INPUT_ACT_LINE_START_H 000 D(D13) INPUT_ACT_LINE_L 176 D(D14) INPUT_ACT_LINE_H 001 D(D15) INPUT_ACT_PIXEL_START_L 020 D(D16) INPUT_ACT_PIXEL_START_H 000 D(D17) INPUT_ACT_PIXEL_L 146 D(D18) INPUT ACT_PIXEL_H 002 D(D19) Not use 105 D(D20) Not use 002 D(D21) WIN_X_MARGINE 113 D(D22) WIN_Y_MARGINE 128 D(D23) WIN_Y_POSI_L 001 D(D24) WIN_Y_POSI_H 000 D(D25) WIN_Y_SIZE_L 224 D(D26) WIN_Y_SIZE_H 001 D(D27) WIN_X_POSI_L 001 D(D28) WIN_X_POSI_H 000 D(D29) WIN_X_SIZE_L 084 D(D30) WIN_X_SIZE_H 002 D(D31) Not use 000 D(D32) Not use 000 D(D33) Not use 000 D(D34) Not use 000 D(D35) Not use 000 D(D36) Not use 000 D(D37) Not use 000 D(D38) COAST_ENABLE 000 D(D39) Not use 000 D(D40) INTERLACE 000 D(D41) Not use 000 D(D42) Not use 000 D(D43) Not use 000 D(D44) Not use 000 D(D45) Not use 000 D(D46) Not use 000 D(D47) Not use 000 D(D48) Not use 000 D(D49) Not use 000 D(D50) Not use 000 D(D51) Not use 000 D(D52) Not use 000

Setting

value

(No.YA064)1-29

Setting No. Setting item

DE : VIDEO-50Hz (REGULAR)

D(E01) FB COUNTER 1 184 D(E02) FB COUNTER 2 006 D(E03) VCO DIVIDE 002 D(E04) DELAY 032 D(E05) CHARGE_PUMP 018 D(E06) AMP MODE 001 D(E07) OUTPUT MODE 006 D(E08) OPLL_MDVI_L 229 D(E09) OPLL_MDVI_H 000 D(E10) OPLL_MDVI 255 D(E11) INPUT_ACT_LINE_START_L 013 D(E12) INPUT_ACT_LINE_START_H 000 D(E13) INPUT_ACT_LINE_L 029 D(E14) INPUT_ACT_LINE_H 002 D(E15) INPUT_ACT_PIXEL_START_L 027 D(E16) INPUT_ACT_PIXEL_START_H 000 D(E17) INPUT_ACT_PIXEL_L 153 D(E18) INPUT ACT_PIXEL_H 002 D(E19) Not use 000 D(E20) Not use 000 D(E21) WIN_X_MARGINE 128 D(E22) WIN_Y_MARGINE 128 D(E23) WIN_Y_POSI_L 001 D(E24) WIN_Y_POSI_H 000 D(E25) WIN_Y_SIZE_L 224 D(E26) WIN_Y_SIZE_H 001 D(E27) WIN_X_POSI_L 106 D(E28) WIN_X_POSI_H 000 D(E29) WIN_X_SIZE_L 128 D(E30) WIN_X_SIZE_H 002 D(E31) Not use 000 D(E32) Not use 000 D(E33) Not use 000 D(E34) Not use 000 D(E35) Not use 000 D(E36) Not use 000 D(E37) Not use 000 D(E38) COAST_ENABLE 000 D(E39) Not use 000 D(E40) INTERLACE 000 D(E41) Not use 000 D(E42) Not use 000 D(E43) Not use 000 D(E44) Not use 000 D(E45) Not use 000 D(E46) Not use 000 D(E47) Not use 000 D(E48) Not use 000 D(E49) Not use 000 D(E50) Not use 000 D(E51) Not use 000 D(E52) Not use 000

Setting

value

Setting No. Setting item

DF : VIDEO-50Hz (FULL)

D(F01) FB COUNTER 1 184 D(F02) FB COUNTER 2 006 D(F03) VCO DIVIDE 002 D(F04) DELAY 032 D(F05) CHARGE_PUMP 018 D(F06) AMP MODE 001 D(F07) OUTPUT MODE 006 D(F08) OPLL_MDVI_L 229 D(F09) OPLL_MDVI_H 000 D(F10) OPLL_MDVI 255 D(F11) INPUT_ACT_LINE_START_L 013 D(F12) INPUT_ACT_LINE_START_H 000 D(F13) INPUT_ACT_LINE_L 029 D(F14) INPUT_ACT_LINE_H 002 D(F15) INPUT_ACT_PIXEL_START_L 028 D(F16) INPUT_ACT_PIXEL_START_H 000 D(F17) INPUT_ACT_PIXEL_L 153 D(F18) INPUT ACT_PIXEL_H 002 D(F19) Not use 000 D(F20) Not use 000 D(F21) WIN_X_MARGINE 128 D(F22) WIN_Y_MARGINE 128 D(F23) WIN_Y_POSI_L 001 D(F24) WIN_Y_POSI_H 000 D(F25) WIN_Y_SIZE_L 224 D(F26) WIN_Y_SIZE_H 001 D(F27) WIN_X_POSI_L 001 D(F28) WIN_X_POSI_H 000 D(F29) WIN_X_SIZE_L 084 D(F30) WIN_X_SIZE_H 003 D(F31) Not use 000 D(F32) Not use 000 D(F33) Not use 000 D(F34) Not use 000 D(F35) Not use 000 D(F36) Not use 000 D(F37) Not use 000 D(F38) COAST_ENABLE 000 D(F39) Not use 000 D(F40) INTERLACE 000 D(F41) Not use 000 D(F42) Not use 000 D(F43) Not use 000 D(F44) Not use 000 D(F45) Not use 000 D(F46) Not use 000 D(F47) Not use 000 D(F48) Not use 000 D(F49) Not use 000 D(F50) Not use 000 D(F51) Not use 000 D(F52) Not use 000

Setting

value

1-30 (No.YA064)

Setting No. Setting item

DG : VIDEO-50Hz (ZOOM)

D(G01) FB COUNTER 1 184 D(G02) FB COUNTER 2 006 D(G03) VCO DIVIDE 002 D(G04) DELAY 032 D(G05) CHARGE_PUMP 018 D(G06) AMP MODE 001 D(G07) OUTPUT MODE 006 D(G08) OPLL_MDVI_L 229 D(G09) OPLL_MDVI_H 000 D(G10) OPLL_MDVI 255 D(G11) INPUT_ACT_LINE_START_L 081 D(G12) INPUT_ACT_LINE_START_H 000 D(G13) INPUT_ACT_LINE_L 153 D(G14) INPUT_ACT_LINE_H 001 D(G15) INPUT_ACT_PIXEL_START_L 028 D(G16) INPUT_ACT_PIXEL_START_H 000 D(G17) INPUT_ACT_PIXEL_L 153 D(G18) INPUT ACT_PIXEL_H 002 D(G19) Not use 000 D(G20) Not use 000 D(G21) WIN_X_MARGINE 128 D(G22) WIN_Y_MARGINE 128 D(G23) WIN_Y_POSI_L 001 D(G24) WIN_Y_POSI_H 000 D(G25) WIN_Y_SIZE_L 224 D(G26) WIN_Y_SIZE_H 001 D(G27) WIN_X_POSI_L 001 D(G28) WIN_X_POSI_H 000 D(G29) WIN_X_SIZE_L 084 D(G30) WIN_X_SIZE_H 003 D(G31) Not use 000 D(G32) Not use 000 D(G33) Not use 000 D(G34) Not use 000 D(G35) Not use 000 D(G36) Not use 000 D(G37) Not use 000 D(G38) COAST_ENABLE 000 D(G39) Not use 000 D(G40) INTERLACE 000 D(G41) Not use 000 D(G42) Not use 000 D(G43) Not use 000 D(G44) Not use 000 D(G45) Not use 000 D(G46) Not use 000 D(G47) Not use 000 D(G48) Not use 000 D(G49) Not use 000 D(G50) Not use 000 D(G51) Not use 000 D(G52) Not use 000

Setting

value

Setting No. Setting item

DH : VIDEO-50Hz (PANORA.)

D(H01) FB COUNTER 1 184 D(H02) FB COUNTER 2 006 D(H03) VCO DIVIDE 002 D(H04) DELAY 032 D(H05) CHARGE_PUMP 018 D(H06) AMP MODE 001 D(H07) OUTPUT MODE 006 D(H08) OPLL_MDVI_L 229 D(H09) OPLL_MDVI_H 000 D(H10) OPLL_MDVI 255 D(H11) INPUT_ACT_LINE_START_L 026 D(H12) INPUT_ACT_LINE_START_H 000 D(H13) INPUT_ACT_LINE_L 001 D(H14) INPUT_ACT_LINE_H 002 D(H15) INPUT_ACT_PIXEL_START_L 024 D(H16) INPUT_ACT_PIXEL_START_H 000 D(H17) INPUT_ACT_PIXEL_L 142 D(H18) INPUT ACT_PIXEL_H 002 D(H19) Not use 105 D(H20) Not use 002 D(H21) WIN_X_MARGINE 113 D(H22) WIN_Y_MARGINE 128 D(H23) WIN_Y_POSI_L 001 D(H24) WIN_Y_POSI_H 000 D(H25) WIN_Y_SIZE_L 224 D(H26) WIN_Y_SIZE_H 001 D(H27) WIN_X_POSI_L 001 D(H28) WIN_X_POSI_H 000 D(H29) WIN_X_SIZE_L 084 D(H30) WIN_X_SIZE_H 003 D(H31) Not use 000 D(H32) Not use 000 D(H33) Not use 000 D(H34) Not use 000 D(H35) Not use 000 D(H36) Not use 000 D(H37) Not use 000 D(H38) COAST_ENABLE 000 D(H39) Not use 000 D(H40) INTERLACE 000 D(H41) Not use 000 D(H42) Not use 000 D(H43) Not use 000 D(H44) Not use 000 D(H45) Not use 000 D(H46) Not use 000 D(H47) Not use 000 D(H48) Not use 000 D(H49) Not use 000 D(H50) Not use 000 D(H51) Not use 000 D(H52) Not use 000

Setting

value

(No.YA064)1-31

Setting No. Setting item

DI : 480P (REGULAR.)

D(I01) FB COUNTER 1 082 D(I02) FB COUNTER 2 003 D(I03) VCO DIVIDE 002 D(I04) DELAY 032 D(I05) CHARGE_PUMP 018 D(I06) AMP MODE 001 D(I07) OUTPUT MODE 000 D(I08) OPLL_MDVI_L 229 D(I09) OPLL_MDVI_H 000 D(I10) OPLL_MDVI 255 D(I11) INPUT_ACT_LINE_START_L 044 D(I12) INPUT_ACT_LINE_START_H 000 D(I13) INPUT_ACT_LINE_L 201 D(I14) INPUT_ACT_LINE_H 001 D(I15) INPUT_ACT_PIXEL_START_L 114 D(I16) INPUT_ACT_PIXEL_START_H 000 D(I17) INPUT_ACT_PIXEL_L 160 D(I18) INPUT ACT_PIXEL_H 002 D(I19) Not use 000 D(I20) Not use 000 D(I21) WIN_X_MARGINE 153 D(I22) WIN_Y_MARGINE 148 D(I23) WIN_Y_POSI_L 001 D(I24) WIN_Y_POSI_H 000 D(I25) WIN_Y_SIZE_L 224 D(I26) WIN_Y_SIZE_H 001 D(I27) WIN_X_POSI_L 106 D(I28) WIN_X_POSI_H 000 D(I29) WIN_X_SIZE_L 128 D(I30) WIN_X_SIZE_H 002 D(I31) Not use 000 D(I32) Not use 000 D(I33) Not use 000 D(I34) Not use 000 D(I35) Not use 000 D(I36) Not use 000 D(I37) Not use 000 D(I38) COAST_ENABLE 000 D(I39) Not use 000 D(I40) INTERLACE 000 D(I41) Not use 000 D(I42) Not use 000 D(I43) Not use 000 D(I44) Not use 000 D(I45) Not use 000 D(I46) Not use 000 D(I47) Not use 000 D(I48) Not use 000 D(I49) Not use 000 D(I50) Not use 000 D(I51) Not use 000 D(I52) Not use 000

Setting

value

Setting No. Setting item

DJ : 480P (FLL.)

D(J01) FB COUNTER 1 082 D(J02) FB COUNTER 2 003 D(J03) VCO DIVIDE 002 D(J04) DELAY 032 D(J05) CHARGE_PUMP 018 D(J06) AMP MODE 001 D(J07) OUTPUT MODE 000 D(J08) OPLL_MDVI_L 229 D(J09) OPLL_MDVI_H 000 D(J10) OPLL_MDVI 255 D(J11) INPUT_ACT_LINE_START_L 044 D(J12) INPUT_ACT_LINE_START_H 000 D(J13) INPUT_ACT_LINE_L 201 D(J14) INPUT_ACT_LINE_H 001 D(J15) INPUT_ACT_PIXEL_START_L 113 D(J16) INPUT_ACT_PIXEL_START_H 000 D(J17) INPUT_ACT_PIXEL_L 162 D(J18) INPUT ACT_PIXEL_H 002 D(J19) Not use 000 D(J20) Not use 000 D(J21) WIN_X_MARGINE 153 D(J22) WIN_Y_MARGINE 148 D(J23) WIN_Y_POSI_L 001 D(J24) WIN_Y_POSI_H 000 D(J25) WIN_Y_SIZE_L 224 D(J26) WIN_Y_SIZE_H 001 D(J27) WIN_X_POSI_L 001 D(J28) WIN_X_POSI_H 000 D(J29) WIN_X_SIZE_L 084 D(J30) WIN_X_SIZE_H 003 D(J31) Not use 000 D(J32) Not use 000 D(J33) Not use 000 D(J34) Not use 000 D(J35) Not use 000 D(J36) Not use 000 D(J37) Not use 000 D(J38) COAST_ENABLE 000 D(J39) Not use 000 D(J40) INTERLACE 000 D(J41) Not use 000 D(J42) Not use 000 D(J43) Not use 000 D(J44) Not use 000 D(J45) Not use 000 D(J46) Not use 000 D(J47) Not use 000 D(J48) Not use 000 D(J49) Not use 000 D(J50) Not use 000 D(J51) Not use 000 D(J52) Not use 000

Setting

value

1-32 (No.YA064)

Setting No. Setting item

DK : 480P (ZOOM.)

D(K01) FB COUNTER 1 82 D(K02) FB COUNTER 2 003 D(K03) VCO DIVIDE 002 D(K04) DELAY 032 D(K05) CHARGE_PUMP 018 D(K06) AMP MODE 001 D(K07) OUTPUT MODE 000 D(K08) OPLL_MDVI_L 229 D(K09) OPLL_MDVI_H 000 D(K10) OPLL_MDVI 255 D(K11) INPUT_ACT_LINE_START_L 102 D(K12) INPUT_ACT_LINE_START_H 000 D(K13) INPUT_ACT_LINE_L 086 D(K14) INPUT_ACT_LINE_H 001 D(K15) INPUT_ACT_PIXEL_START_L 113 D(K16) INPUT_ACT_PIXEL_START_H 000 D(K17) INPUT_ACT_PIXEL_L 162 D(K18) INPUT ACT_PIXEL_H 002 D(K19) Not use 000 D(K20) Not use 000 D(K21) WIN_X_MARGINE 153 D(K22) WIN_Y_MARGINE 188 D(K23) WIN_Y_POSI_L 001 D(K24) WIN_Y_POSI_H 000 D(K25) WIN_Y_SIZE_L 224 D(K26) WIN_Y_SIZE_H 001 D(K27) WIN_X_POSI_L 001 D(K28) WIN_X_POSI_H 000 D(K29) WIN_X_SIZE_L 084 D(K30) WIN_X_SIZE_H 003 D(K31) Not use 000 D(K32) Not use 000 D(K33) Not use 000 D(K34) Not use 000 D(K35) Not use 000 D(K36) Not use 000 D(K37) Not use 000 D(K38) COAST_ENABLE 000 D(K39) Not use 000 D(K40) INTERLACE 000 D(K41) Not use 000 D(K42) Not use 000 D(K43) Not use 000 D(K44) Not use 000 D(K45) Not use 000 D(K46) Not use 000 D(K47) Not use 000 D(K48) Not use 000 D(K49) Not use 000 D(K50) Not use 000 D(K51) Not use 000 D(K52) Not use 000

Setting

value

Setting No. Setting item

DL : 480P (PANORAMIC.)

D(L01) FB COUNTER 1 082 D(L02) FB COUNTER 2 003 D(L03) VCO DIVIDE 002 D(L04) DELAY 032 D(L05) CHARGE_PUMP 018 D(L06) AMP MODE 001 D(L07) OUTPUT MODE 000 D(L08) OPLL_MDVI_L 229 D(L09) OPLL_MDVI_H 000 D(L10) OPLL_MDVI 255 D(L11) INPUT_ACT_LINE_START_L 056 D(L12) INPUT_ACT_LINE_START_H 000 D(L13) INPUT_ACT_LINE_L 177 D(L14) INPUT_ACT_LINE_H 001 D(L15) INPUT_ACT_PIXEL_START_L 113 D(L16) INPUT_ACT_PIXEL_START_H 000 D(L17) INPUT_ACT_PIXEL_L 164 D(L18) INPUT ACT_PIXEL_H 002 D(L19) DS_OUTX_PANO_L 122 D(L20) DS_OUTX_PANO_H 002 D(L21) WIN_X_MARGINE 148 D(L22) WIN_Y_MARGINE 160 D(L23) WIN_Y_POSI_L 001 D(L24) WIN_Y_POSI_H 000 D(L25) WIN_Y_SIZE_L 224 D(L26) WIN_Y_SIZE_H 001 D(L27) WIN_X_POSI_L 001 D(L28) WIN_X_POSI_H 000 D(L29) WIN_X_SIZE_L 084 D(L30) WIN_X_SIZE_H 003 D(L31) Not use 000 D(L32) Not use 000 D(L33) Not use 000 D(L34) Not use 000 D(L35) Not use 000 D(L36) Not use 000 D(L37) Not use 000 D(L38) COAST_ENABLE 000 D(L39) Not use 000 D(L40) INTERLACE 000 D(L41) Not use 000 D(L42) Not use 000 D(L43) Not use 000 D(L44) Not use 000 D(L45) Not use 000 D(L46) Not use 000 D(L47) Not use 000 D(L48) Not use 000 D(L49) Not use 000 D(L50) Not use 000 D(L51) Not use 000 D(L52) Not use 000

Setting

value

(No.YA064)1-33

Setting No. Setting item

DM : 576P (REGULAR)

D(M01) FB COUNTER 1 88 D(M02) FB COUNTER 2 003 D(M03) VCO DIVIDE 002 D(M04) DELAY 032 D(M05) CHARGE_PUMP 018 D(M06) AMP MODE 001 D(M07) OUTPUT MODE 000 D(M08) OPLL_MDVI_L 229 D(M09) OPLL_MDVI_H 000 D(M10) OPLL_MDVI 255 D(M11) INPUT_ACT_LINE_START_L 053 D(M12) INPUT_ACT_LINE_START_H 000 D(M13) INPUT_ACT_LINE_L 035 D(M14) INPUT_ACT_LINE_H 002 D(M15) INPUT_ACT_PIXEL_START_L 129 D(M16) INPUT_ACT_PIXEL_START_H 000 D(M17) INPUT_ACT_PIXEL_L 148 D(M18) INPUT ACT_PIXEL_H 002 D(M19) Not use 000 D(M20) Not use 000 D(M21) WIN_X_MARGINE 158 D(M22) WIN_Y_MARGINE 153 D(M23) WIN_Y_POSI_L 001 D(M24) WIN_Y_POSI_H 000 D(M25) WIN_Y_SIZE_L 224 D(M26) WIN_Y_SIZE_H 001 D(M27) WIN_X_POSI_L 106 D(M28) WIN_X_POSI_H 000 D(M29) WIN_X_SIZE_L 128 D(M30) WIN_X_SIZE_H 002 D(M31) Not use 000 D(M32) Not use 000 D(M33) Not use 000 D(M34) Not use 000 D(M35) Not use 000 D(M36) Not use 000 D(M37) Not use 000 D(M38) COAST_ENABLE 000 D(M39) Not use 000 D(M40) INTERLACE 000 D(M41) Not use 000 D(M42) Not use 000 D(M43) Not use 000 D(M44) Not use 000 D(M45) Not use 000 D(M46) Not use 000 D(M47) Not use 000 D(M48) Not use 000 D(M49) Not use 000 D(M50) Not use 000 D(M51) Not use 000 D(M52) Not use 000

Setting

value

Setting No. Setting item

DN : 576P (FULL)

D(N01) FB COUNTER 1 088 D(N02) FB COUNTER 2 003 D(N03) VCO DIVIDE 002 D(N04) DELAY 032 D(N05) CHARGE_PUMP 018 D(N06) AMP MODE 001 D(N07) OUTPUT MODE 000 D(N08) OPLL_MDVI_L 229 D(N09) OPLL_MDVI_H 000 D(N10) OPLL_MDVI 255 D(N11) INPUT_ACT_LINE_START_L 053 D(N12) INPUT_ACT_LINE_START_H 000 D(N13) INPUT_ACT_LINE_L 035 D(N14) INPUT_ACT_LINE_H 002 D(N15) INPUT_ACT_PIXEL_START_L 129 D(N16) INPUT_ACT_PIXEL_START_H 000 D(N17) INPUT_ACT_PIXEL_L 150 D(N18) INPUT ACT_PIXEL_H 002 D(N19) Not use 000 D(N20) Not use 000 D(N21) WIN_X_MARGINE 158 D(N22) WIN_Y_MARGINE 153 D(N23) WIN_Y_POSI_L 001 D(N24) WIN_Y_POSI_H 000 D(N25) WIN_Y_SIZE_L 224 D(N26) WIN_Y_SIZE_H 001 D(N27) WIN_X_POSI_L 001 D(N28) WIN_X_POSI_H 000 D(N29) WIN_X_SIZE_L 084 D(N30) WIN_X_SIZE_H 003 D(N31) Not use 000 D(N32) Not use 000 D(N33) Not use 000 D(N34) Not use 000 D(N35) Not use 000 D(N36) Not use 000 D(N37) Not use 000 D(N38) COAST_ENABLE 000 D(N39) Not use 000 D(N40) INTERLACE 000 D(N41) Not use 000 D(N42) Not use 000 D(N43) Not use 000 D(N44) Not use 000 D(N45) Not use 000 D(N46) Not use 000 D(N47) Not use 000 D(N48) Not use 000 D(N49) Not use 000 D(N50) Not use 000 D(N51) Not use 000 D(N52) Not use 000

Setting

value

1-34 (No.YA064)

Setting No. Setting item

DO : 576P (ZOOM)

D(O01) FB COUNTER 1 088 D(O02) FB COUNTER 2 003 D(O03) VCO DIVIDE 002 D(O04) DELAY 032 D(O05) CHARGE_PUMP 018 D(O06) AMP MODE 001 D(O07) OUTPUT MODE 000 D(O08) OPLL_MDVI_L 229 D(O09) OPLL_MDVI_H 000 D(O10) OPLL_MDVI 255 D(O11) INPUT_ACT_LINE_START_L 110 D(O12) INPUT_ACT_LINE_START_H 000 D(O13) INPUT_ACT_LINE_L 154 D(O14) INPUT_ACT_LINE_H 001 D(O15) INPUT_ACT_PIXEL_START_L 129 D(O16) INPUT_ACT_PIXEL_START_H 000 D(O17) INPUT_ACT_PIXEL_L 150 D(O18) INPUT ACT_PIXEL_H 002 D(O19) Not use 000 D(O20) Not use 000 D(O21) WIN_X_MARGINE 158 D(O22) WIN_Y_MARGINE 188 D(O23) WIN_Y_POSI_L 001 D(O24) WIN_Y_POSI_H 000 D(O25) WIN_Y_SIZE_L 224 D(O26) WIN_Y_SIZE_H 001 D(O27) WIN_X_POSI_L 001 D(O28) WIN_X_POSI_H 000 D(O29) WIN_X_SIZE_L 084 D(O30) WIN_X_SIZE_H 003 D(O31) Not use 000 D(O32) Not use 000 D(O33) Not use 000 D(O34) Not use 000 D(O35) Not use 000 D(O36) Not use 000 D(O37) Not use 000 D(O38) COAST_ENABLE 000 D(O39) Not use 000 D(O40) INTERLACE 000 D(O41) Not use 000 D(O42) Not use 000 D(O43) Not use 000 D(O44) Not use 000 D(O45) Not use 000 D(O46) Not use 000 D(O47) Not use 000 D(O48) Not use 000 D(O49) Not use 000 D(O50) Not use 000 D(O51) Not use 000 D(O52) Not use 000

Setting

value

Setting No. Setting item

DP : 576P (PANORAMIC)

D(P01) FB COUNTER 1 088 D(P02) FB COUNTER 2 003 D(P03) VCO DIVIDE 002 D(P04) DELAY 032 D(P05) CHARGE_PUMP 018 D(P06) AMP MODE 001 D(P07) OUTPUT MODE 000 D(P08) OPLL_MDVI_L 229 D(P09) OPLL_MDVI_H 000 D(P10) OPLL_MDVI 255 D(P11) INPUT_ACT_LINE_START_L 067 D(P12) INPUT_ACT_LINE_START_H 000 D(P13) INPUT_ACT_LINE_L 007 D(P14) INPUT_ACT_LINE_H 002 D(P15) INPUT_ACT_PIXEL_START_L 124 D(P16) INPUT_ACT_PIXEL_START_H 000 D(P17) INPUT_ACT_PIXEL_L 162 D(P18) INPUT ACT_PIXEL_H 002 D(P19) Not use 122 D(P20) Not use 002 D(P21) WIN_X_MARGINE 153 D(P22) WIN_Y_MARGINE 168 D(P23) WIN_Y_POSI_L 001 D(P24) WIN_Y_POSI_H 000 D(P25) WIN_Y_SIZE_L 224 D(P26) WIN_Y_SIZE_H 001 D(P27) WIN_X_POSI_L 001 D(P28) WIN_X_POSI_H 000 D(P29) WIN_X_SIZE_L 084 D(P30) WIN_X_SIZE_H 003 D(P31) Not use 000 D(P32) Not use 000 D(P33) Not use 000 D(P34) Not use 000 D(P35) Not use 000 D(P36) Not use 000 D(P37) Not use 000 D(P38) COAST_ENABLE 000 D(P39) Not use 000 D(P40) INTERLACE 000 D(P41) Not use 000 D(P42) Not use 000 D(P43) Not use 000 D(P44) Not use 000 D(P45) Not use 000 D(P46) Not use 000 D(P47) Not use 000 D(P48) Not use 000 D(P49) Not use 000 D(P50) Not use 000 D(P51) Not use 000 D(P52) Not use 000

Setting

value

(No.YA064)1-35

Setting No. Setting item

DQ : COMPO.-720P

D(Q01) FB COUNTER 1 106 D(Q02) FB COUNTER 2 006 D(Q03) VCO DIVIDE 001 D(Q04) DELAY 035 D(Q05) CHARGE_PUMP 020 D(Q06) AMP MODE 001 D(Q07) OUTPUT MODE 000 D(Q08) OPLL_MDVI_L 229 D(Q09) OPLL_MDVI_H 000 D(Q10) OPLL_MDVI 255 D(Q11) INPUT_ACT_LINE_START_L 037 D(Q12) INPUT_ACT_LINE_START_H 000 D(Q13) INPUT_ACT_LINE_L 173 D(Q14) INPUT_ACT_LINE_H 002 D(Q15) INPUT_ACT_PIXEL_START_L 032 D(Q16) INPUT_ACT_PIXEL_START_H 001 D(Q17) INPUT_ACT_PIXEL_L 184 D(Q18) INPUT ACT_PIXEL_H 004 D(Q19) Not use 000 D(Q20) Not use 000 D(Q21) WIN_X_MARGINE 178 D(Q22) WIN_Y_MARGINE 153 D(Q23) WIN_Y_POSI_L 001 D(Q24) WIN_Y_POSI_H 000 D(Q25) WIN_Y_SIZE_L 224 D(Q26) WIN_Y_SIZE_H 001 D(Q27) WIN_X_POSI_L 001 D(Q28) WIN_X_POSI_H 000 D(Q29) WIN_X_SIZE_L 084 D(Q30) WIN_X_SIZE_H 003 D(Q31) Not use 000 D(Q32) Not use 000 D(Q33) Not use 000 D(Q34) Not use 000 D(Q35) Not use 000 D(Q36) Not use 000 D(Q37) Not use 000 D(Q38) COAST_ENABLE 000 D(Q39) Not use 000 D(Q40) INTERLACE 000 D(Q41) Not use 000 D(Q42) Not use 000 D(Q43) Not use 000 D(Q44) Not use 000 D(Q45) Not use 000 D(Q46) Not use 000 D(Q47) Not use 000 D(Q48) Not use 000 D(Q49) Not use 000 D(Q50) Not use 000 D(Q51) Not use 000 D(Q52) Not use 000

Setting

value

Setting No. Setting item

DR : COMPO.-1080/60i

D(R01) FB COUNTER 1 188 D(R02) FB COUNTER 2 005 D(R03) VCO DIVIDE 001 D(R04) DELAY 040 D(R05) CHARGE_PUMP 020 D(R06) AMP MODE 001 D(R07) OUTPUT MODE 000 D(R08) OPLL_MDVI_L 229 D(R09) OPLL_MDVI_H 000 D(R10) OPLL_MDVI 255 D(R11) INPUT_ACT_LINE_START_L 028 D(R12) INPUT_ACT_LINE_START_H 000 D(R13) INPUT_ACT_LINE_L 001 D(R14) INPUT_ACT_LINE_H 002 D(R15) INPUT_ACT_PIXEL_START_L 155 D(R16) INPUT_ACT_PIXEL_START_H 000 D(R17) INPUT_ACT_PIXEL_L 192 D(R18) INPUT ACT_PIXEL_H 004 D(R19) Not use 000 D(R20) Not use 000 D(R21) WIN_X_MARGINE 208 D(R22) WIN_Y_MARGINE 144 D(R23) WIN_Y_POSI_L 001 D(R24) WIN_Y_POSI_H 000 D(R25) WIN_Y_SIZE_L 224 D(R26) WIN_Y_SIZE_H 001 D(R27) WIN_X_POSI_L 001 D(R28) WIN_X_POSI_H 000 D(R29) WIN_X_SIZE_L 84 D(R30) WIN_X_SIZE_H 003 D(R31) Not use 000 D(R32) Not use 000 D(R33) Not use 000 D(R34) Not use 000 D(R35) Not use 000 D(R36) Not use 000 D(R37) Not use 000 D(R38) COAST_ENABLE 000 D(R39) Not use 000 D(R40) INTERLACE 000 D(R41) Not use 000 D(R42) Not use 000 D(R43) Not use 000 D(R44) Not use 000 D(R45) Not use 000 D(R46) Not use 000 D(R47) Not use 000 D(R48) Not use 000 D(R49) Not use 000 D(R50) Not use 000 D(R51) Not use 000 D(R52) Not use 000

Setting

value

1-36 (No.YA064)

Setting No. Setting item

DS : COMPO.-1080/50i

D(S01) FB COUNTER 1 226 D(S02) FB COUNTER 2 006 D(S03) VCO DIVIDE 001 D(S04) DELAY 035 D(S05) CHARGE_PUMP 020 D(S06) AMP MODE 001 D(S07) OUTPUT MODE 000 D(S08) OPLL_MDVI_L 229 D(S09) OPLL_MDVI_H 000 D(S10) OPLL_MDVI 255 D(S11) INPUT_ACT_LINE_START_L 028 D(S12) INPUT_ACT_LINE_START_H 000 D(S13) INPUT_ACT_LINE_L 001 D(S14) INPUT_ACT_LINE_H 002 D(S15) INPUT_ACT_PIXEL_START_L 132 D(S16) INPUT_ACT_PIXEL_START_H 000 D(S17) INPUT_ACT_PIXEL_L 192 D(S18) INPUT ACT_PIXEL_H 004 D(S19) Not use 000 D(S20) Not use 000 D(S21) WIN_X_MARGINE 208 D(S22) WIN_Y_MARGINE 144 D(S23) WIN_Y_POSI_L 001 D(S24) WIN_Y_POSI_H 000 D(S25) WIN_Y_SIZE_L 224 D(S26) WIN_Y_SIZE_H 001 D(S27) WIN_X_POSI_L 001 D(S28) WIN_X_POSI_H 000 D(S29) WIN_X_SIZE_L 084 D(S30) WIN_X_SIZE_H 003 D(S31) Not use 000 D(S32) Not use 000 D(S33) Not use 000 D(S34) Not use 000 D(S35) Not use 000 D(S36) Not use 000 D(S37) Not use 000 D(S38) COAST_ENABLE 000 D(S39) Not use 000 D(S40) INTERLACE 000 D(S41) Not use 000 D(S42) Not use 000 D(S43) Not use 000 D(S44) Not use 000 D(S45) Not use 000 D(S46) Not use 000 D(S47) Not use 000 D(S48) Not use 000 D(S49) Not use 000 D(S50) Not use 000 D(S51) Not use 000 D(S52) Not use 000

Setting

value

Setting No. Setting item

DT : COMPO.-1035i

D(T01) FB COUNTER 1 188 D(T02) FB COUNTER 2 005 D(T03) VCO DIVIDE 001 D(T04) DELAY 032 D(T05) CHARGE_PUMP 020 D(T06) AMP MODE 001 D(T07) OUTPUT MODE 000 D(T08) OPLL_MDVI_L 229 D(T09) OPLL_MDVI_H 000 D(T10) OPLL_MDVI 255 D(T11) INPUT_ACT_LINE_START_L 047 D(T12) INPUT_ACT_LINE_START_H 000 D(T13) INPUT_ACT_LINE_L 236 D(T14) INPUT_ACT_LINE_H 001 D(T15) INPUT_ACT_PIXEL_START_L 155 D(T16) INPUT_ACT_PIXEL_START_H 000 D(T17) INPUT_ACT_PIXEL_L 192 D(T18) INPUT ACT_PIXEL_H 004 D(T19) Not use 000 D(T20) Not use 000 D(T21) WIN_X_MARGINE 208 D(T22) WIN_Y_MARGINE 148 D(T23) WIN_Y_POSI_L 001 D(T24) WIN_Y_POSI_H 000 D(T25) WIN_Y_SIZE_L 224 D(T26) WIN_Y_SIZE_H 001 D(T27) WIN_X_POSI_L 001 D(T28) WIN_X_POSI_H 000 D(T29) WIN_X_SIZE_L 084 D(T30) WIN_X_SIZE_H 003 D(T31) Not use 000 D(T32) Not use 000 D(T33) Not use 000 D(T34) Not use 000 D(T35) Not use 000 D(T36) Not use 000 D(T37) Not use 000 D(T38) COAST_ENABLE 000 D(T39) Not use 000 D(T40) INTERLACE 000 D(T41) Not use 000 D(T42) Not use 000 D(T43) Not use 000 D(T44) Not use 000 D(T45) Not use 000 D(T46) Not use 000 D(T47) Not use 000 D(T48) Not use 000 D(T49) Not use 000 D(T50) Not use 000 D(T51) Not use 000 D(T52) Not use 000

Setting

value

(No.YA064)1-37

 H POSITION BLOCK

Setting No. Setting item

PA : VIDEO

P(A01) NTSC REGULAR 000 P(A02) NTSC FULL 000 P(A03) NTSC ZOOM 000 P(A04) NTSC PANARAMIC 000 P(A05) N443 REGULAR 000 P(A06) N443 FULL 000 P(A07) N443ZOOM 000 P(A08) N443 PANARAMIC 000 P(A09) PAL M REGULAR 000 P(A10) PAL M FULL 000 P(A11) PAL M ZOOM 000 P(A12) PAL M PANARAMIC 000 P(A13) PAL60 REGULAR 000 P(A14) PAL60 FULL 000 P(A15) PAL60 ZOOM 000 P(A16) PAL60 PANARAMIC 000 P(A17) BW60 REGULAR 000 P(A18) BW60 FULL 000 P(A19) BW60 ZOOM 000 P(A20) BW60 PANARAMIC 000 P(A21) PAL REGULAR 000 P(A22) PAL FULL 000 P(A23) PAL ZOOM 000 P(A24) PAL PANARAMIC 000 P(A25) PAL N REGULAR 000 P(A26) PAL N FULL 000 P(A27) PAL N ZOOM 000 P(A28) PAL N PANARAMIC 000 P(A29) SECAM REGULAR 000 P(A30) SECAM FULL 000 P(A31) SECAM ZOOM 000 P(A32) SECAM PANARAMIC 000 P(A33) BW50 REGULAR 000 P(A34) BW50 FULL 000 P(A35) BW50 ZOOM 000 P(A36) BW50 PANARAMIC 000

PB : Y/C

P(B01) NTSC REGULAR 000 P(B02) NTSC FULL 000 P(B03) NTSC ZOOM 000 P(B04) NTSC PANARAMIC 000 P(B05) N443 REGULAR 000 P(B06) N443 FULL 000 P(B07) N443 ZOOM 000 P(B08) N443 PANARAMIC 000 P(B09) PAL M REGULAR 000 P(B10) PAL M FULL 000 P(B11) PAL M ZOOM 000 P(B12) PAL M PANARAMIC 000 P(B13) PAL60 REGULAR 000 P(B14) PAL60 FULL 000 P(B15) PAL60 ZOOM 000 P(B16) PAL60 PANARAMIC 000

Setting

value

Setting No. Setting item

P(B17) BW60 REGULAR 000 P(B18) BW60 FULL 000 P(B19) BW60 ZOOM 000 P(B20) BW60 PANARAMIC 000 P(B21) PAL REGULAR 000 P(B22) PAL FULL 000 P(B23) PAL ZOOM 000 P(B24) PAL PANARAMIC 000 P(B25) PAL N REGULAR 000 P(B26) PAL N FULL 000 P(B27) PAL N ZOOM 000 P(B28) PAL N PANARAMIC 000 P(B29) SECAM REGULAR 000 P(B30) SECAM FULL 000 P(B31) SECAM ZOOM 000 P(B32) SECAM PANARAMIC 000 P(B33) BW50 REGULAR 000 P(B34) BW50 FULL 000 P(B35) BW50 ZOOM 000 P(B36) BW50 PANARAMIC 000

PC : COMPO.

P(C01) 480i REGULAR +001 P(C02) 480i FULL +001 P(C03) 480i ZOOM +001 P(C04) 480i PANARAMIC +001 P(C05) 576i REGULAR +003 P(C06) 576i FULL +003 P(C07) 576i ZOOM +003 P(C08) 576i PANARAMIC +003 P(C09) 480p REGULAR 000 P(C10) 480p FULL 000 P(C11) 480p ZOOM 000 P(C12) 480p PANARAMIC 000 P(C13) 576P REGULAR 000 P(C14) 576P FULL 000 P(C15) 576P ZOOM 000 P(C16) 576P PANARAMIC 000 P(C17) 720PREGULAR 000 P(C18) 1080/60i FULL 000 P(C19) 1080/50i ZOOM 000 P(C20) 1035i PANARAMIC 000

Setting

value

1-38 (No.YA064)

Setting No. Setting item

PD : RGB

P(D01) RGB15K60 REGULAR 000 P(D02) RGB15K60 FULL 000 P(D03) RGB15K60 ZOOM 000 P(D04) RGB15K60 PANARAMIC 000 P(D05) RGB15K50 REGULAR 000 P(D06) RGB15K50 FULL 000 P(D07) RGB15K50 ZOOM 000 P(D08) RGB15K50 PANARAMIC 000 P(D09) VGA400/56 REGULAR 000 P(D10) VGA400/56 FULL 000 P(D11) VGA400/70 REGULAR 000 P(D12) VGA400/70 FULL 000 P(D13) VGA/60 REGULAR 000 P(D14) VGA/60 FULL 000 P(D15) VGA/72 REGULAR 000 P(D16) VGA/72 FULL 000 P(D17) VGA/75 REGULAR 000 P(D18) VGA/75 FULL 000 P(D19) MAC13 REGULAR 000

Setting

value

Setting No. Setting item

P(D20) MAC13 FULL 000 P(D21) SVGA/56 REGULAR 000 P(D22) SVGA/56 FULL 000 P(D23) SVGA/60 REGULAR 000 P(D24) SVGA/60 FULL 000 P(D25) SVGA/72 REGULAR 000 P(D26) SVGA/72 FULL 000 P(D27) SVGA/75 REGULAR 000 P(D28) SVGA/75 FULL 000 P(D29) XGA/60 REGULAR 000 P(D30) XGA/60 FULL 000 P(D31) XGA/70 REGULAR 000 P(D32) XGA/70 FULL 000 P(D33) XGA/75REGULAR 000 P(D34) XGA/75 FULL 000 P(D35) XGA/85 REGULAR 000 P(D36) XGA/85 FULL 000 P(D37) XGA+/75 REGULAR 000 P(D38) XGA+/75 FULL 000

Setting

value

(No.YA064)1-39

 PANEL BLOCK

Setting No. Setting item

BA : VIDEO 50Hz

B(A01) GM_CORR_SEL 000 B(A02) GM_CORR_SW 000 B(A03) JVC_ED 000 B(A04) JVC_DITH 000 B(A05) R_LGE_LOW_BOUND 013 B(A06) R_LGE_HIGH_BOUND 180 B(A07) FCR 000 B(A08) GM 001 B(A09) GT 001 B(A10) ED 002 B(A11) EXT_APS_EN 085 B(A12) EDR 000 B(A13) EDT 001 B(A14) EDP 001 B(A15) GTS_P_HYS 000 B(A16) GTS_N_HYS 000 B(A17) ED_NOISE_QTY 255 B(A18) R_SUS_MIN_APC_0 000 B(A19) R_LGE_SW 001 B(A20) R_LGE_HEIGHT 004

BB : COMPO. -480i/576i

B(B01) GM_CORR_SEL 000 B(B02) GM_CORR_SW 000 B(B03) JVC_ED 000 B(B04) JVC_DITH 000 B(B05) R_LGE_LOW_BOUND 013 B(B06) R_LGE_HIGH_BOUND 180 B(B07) FCR 000 B(B08) GM 001

Setting

value

Setting No. Setting item

B(B09) GT 001 B(B10) ED 002 B(B11) EXT_APS_EN 085 B(B12) EDR 000 B(B13) EDT 001 B(B14) EDP 001 B(B15) GTS_P_HYS 000 B(B16) GTS_N_HYS 000 B(B17) ED_NOISE_QTY 255 B(B18) R_SUS_MIN_APC_0 000 B(B19) R_LGE_SW 001 B(B20) R_LGE_HEIGHT 004

BC : COMPO. -OTHERS

B(C01) CORDING SELECT 001 B(C02) PRIMING CONT. 000 B(C03) CONTRARY GAMMA. 002 B(C04) ERROR DIFFUSION 007 B(C05) NR GAIN 000

BD : RGB -15k

B(D01) CORDING SELECT 002 B(D02) PRIMING CONT. 000 B(D03) CONTRARY GAMMA. 002 B(D04) ERROR DIFFUSION 007 B(D05) NR GAIN 000

BE : RGB -PC

B(E01) CORDING SELECT 001 B(E02) PRIMING CONT. 000 B(E03) CONTRARY GAMMA. 002 B(E04) ERROR DIFFUSION 007 B(E05) NR GAIN 000

Setting

value

1-40 (No.YA064)

 SIGNAL BLOCK

Setting No. Setting item

SA : VIDEO -NTSC

S(A01) LPF 000 S(A02) SUB BRIGHT 016 S(A03) SHARPNESS 001 S(A04) SUB CONTRAST 109 S(A05) YC DLAY (H) 15 S(A06) YC DLAY (L) 192 S(A07) VERT PEAK GAIN 001 S(A08) COM FILTER 103 S(A09) SUB COLOR (H) 007 S(A10) SUB COLOR (L) 005 S(A11) SUB TINT (H) 000 S(A12) SUB TINT (L) 000

SB : VIDEO -PAL

S(B01) LPF 000 S(B02) SUB BRIGHT 016 S(B03) SHARPNESS 001 S(B04) SUB CONTRAST 109 S(B05) YC DLAY (H) 15 S(B06) YC DLAY (L) 128 S(B07) VERT PEAK GAIN 001 S(B08) COM FILTER 231 S(B09) SUB COLOR (H) 007 S(B10) SUB COLOR (L) 005 S(B11) SUB TINT (H) 000 S(B12) SUB TINT (L) 000

SC : VIDEO -SECAM

S(C01) LPF 000 S(C02) SUB BRIGHT 016 S(C03) SHARPNESS 001 S(C04) SUB CONTRAST 173 S(C05) YC DLAY (H) 15 S(C06) YC DLAY (L) 128 S(C07) VERT PEAK GAIN 001 S(C08) COM FILTER 231 S(C09) SUB COLOR (H) 007 S(C10) SUB COLOR (L) 005 S(C11) SUB TINT (H) 000 S(C12) SUB TINT (L) 000

SD : VIDEO -NTSC4.43

S(D01) LPF 000 S(D02) SUB BRIGHT 016 S(D03) SHARPNESS 001 S(D04) SUB CONTRAST 173 S(D05) YC DLAY (H) 015 S(D06) YC DLAY (L) 192 S(D07) VERT PEAK GAIN 001 S(D08) COM FILTER 231 S(D09) SUB COLOR (H) 007 S(D10) SUB COLOR (L) 005 S(D11) SUB TINT (H) 000 S(D12) SUB TINT (L) 000

Setting

value

Setting No. Setting item

SE : VIDEO -PALM

S(E01) LPF 000 S(E02) SUB BRIGHT 016 S(E03) SHARPNESS 001 S(E04) SUB CONTRAST 173 S(E05) YC DLAY (H) 15 S(E06) YC DLAY (L) 128 S(E07) VERT PEAK GAIN 001 S(E08) COM FILTER 231 S(E09) SUB COLOR (H) 007 S(E10) SUB COLOR (L) 005 S(E11) SUB TINT (H) 000 S(E12) SUB TINT (L) 000

SF : VIDEO -PALN

S(F01) LPF 000 S(F02) SUB BRIGHT 016 S(F03) SHARPNESS 001 S(F04) SUB CONTRAST 173 S(F05) YC DLAY (H) 015 S(F06) YC DLAY (L) 128 S(F07) VERT PEAK GAIN 001 S(F08) COM FILTER 231 S(F09) SUB COLOR (H) 007 S(F10) SUB COLOR (L) 005 S(F11) SUB TINT (H) 000 S(F12) SUB TINT (L) 000

SG : VIDEO -PAL-60

S(G01) LPF 000 S(G02) SUB BRIGHT 016 S(G03) SHARPNESS 001 S(G04) SUB CONTRAST 173 S(G05) YC DLAY (H) 015 S(G06) YC DLAY (L) 128 S(G07) VERT PEAK GAIN 001 S(G08) COM FILTER 231 S(G09) SUB COLOR (H) 007 S(G10) SUB COLOR (L) 005 S(G11) SUB TINT (H) 000 S(G12) SUB TINT (L) 000

SH : Y/C -NTSC

S(H01) LPF 000 S(H02) SUB BRIGHT 016 S(H03) SHARPNESS 001 S(H04) SUB CONTRAST 109 S(H05) YC DLAY (H) 015 S(H06) YC DLAY (L) 192 S(H07) VERT PEAK GAIN 001 S(H08) COM FILTER 231 S(H09) SUB COLOR (H) 007 S(H10) SUB COLOR (L) 005 S(H11) SUB TINT (H) 000 S(H12) SUB TINT (L) 000

Setting

value

(No.YA064)1-41

Setting No. Setting item

SI : Y/C -PAL

S(I01) LPF 000 S(I02) SUB BRIGHT 016 S(I03) SHARPNESS 001 S(I04) SUB CONTRAST 109 S(I05) YC DLAY (H) 015 S(I06) YC DLAY (L) 128 S(I07) VERT PEAK GAIN 001 S(I08) COM FILTER 231 S(I09) SUB COLOR (H) 007 S(I10) SUB COLOR (L) 005 S(I11) SUB TINT (H) 000 S(I12) SUB TINT (L) 000

SJ : Y/C -SECAM

S(J01) LPF 000 S(J02) SUB BRIGHT 016 S(J03) SHARPNESS 001 S(J04) SUB CONTRAST 173 S(J05) YC DLAY (H) 015 S(J06) YC DLAY (L) 128 S(J07) VERT PEAK GAIN 001 S(J08) COM FILTER 231 S(J09) SUB COLOR (H) 007 S(J10) SUB COLOR (L) 005 S(J11) SUB TINT (H) 000 S(J12) SUB TINT (L) 000

SK : Y/C -NTSC4.43

S(K01) LPF 000 S(K02) SUB BRIGHT 016 S(K03) SHARPNESS 001 S(K04) SUB CONTRAST 173 S(K05) YC DLAY (H) 015 S(K06) YC DLAY (L) 192 S(K07) VERT PEAK GAIN 001 S(K08) COM FILTER 231 S(K09) SUB COLOR (H) 007 S(K10) SUB COLOR (L) 005 S(K11) SUB TINT (H) 000 S(K12) SUB TINT (L) 000

SL : Y/C -PALM

S(L01) LPF 000 S(L02) SUB BRIGHT 016 S(L03) SHARPNESS 001 S(L04) SUB CONTRAST 173 S(L05) YC DLAY (H) 015 S(L06) YC DLAY (L) 128 S(L07) VERT PEAK GAIN 001 S(L08) COM FILTER 231 S(L09) SUB COLOR (H) 007 S(L10) SUB COLOR (L) 005 S(L11) SUB TINT (H) 000 S(L12) SUB TINT (L) 000

Setting

value

Setting No. Setting item

SM : Y/C -PALN

S(M01) LPF 000 S(M02) SUB BRIGHT 016 S(M03) SHARPNESS 001 S(M04) SUB CONTRAST 173 S(M05) YC DLAY (H) 015 S(M06) YC DLAY (L) 128 S(M07) VERT PEAK GAIN 001 S(M08) COM FILTER 231 S(M09) SUB COLOR (H) 007 S(M10) SUB COLOR (L) 005 S(M11) SUB TINT (H) 000 S(M12) SUB TINT (L) 000

SN : Y/C -PAL-60

S(N01) LPF 000 S(N02) SUB BRIGHT 016 S(N03) SHARPNESS 001 S(N04) SUB CONTRAST 173 S(N05) YC DLAY (H) 015 S(N06) YC DLAY (L) 128 S(N07) VERT PEAK GAIN 001 S(N08) COM FILTER 231 S(N09) SUB COLOR (H) 007 S(N10) SUB COLOR (L) 005 S(N11) SUB TINT (H) 000 S(N12) SUB TINT (L) 000

SO : COMPO. -480i/576i

S(O01) LPF 000 S(O02) SUB BRIGHT 016 S(O03) SHARPNESS 001 S(O04) SUB CONTRAST 109

Setting

value

1-42 (No.YA064)

 DEVICE INITIAL VALUE

Setting No. Setting item

IA : VPC3230D

I(A001) SYNC PIN CONTROL 014 I(A002) 000 I(A003) SYNC GENERATOR CONTROL 000 I(A004) 000 I(A005) OUTPUT STRENGTH 000 I(A006) 000 I(A007) V-SYNC DELAY CONTROL 000 I(A008) 027 I(A009) 656 OUTPUT INTERFACE 000 I(A010) 032 I(A011) LINE LENGTH 003 I(A012) 089 I(A013) HC START 000 I(A014) 050 I(A015) HC STOP 003 I(A016) 032 I(A017) AVO START 016 I(A018) 105 I(A019) AVO STOP 003 I(A020) 056 I(A021) NEWLINE 000 I(A022) 104 I(A023) VPC MODE 000 I(A024) 000 I(A025) PIP MODE 000 I(A026) 000 I(A027) PIP OPERATION 000 I(A028) 000 I(A029) BACKGROUND COLOR 000 I(A030) 000 I(A031) FRAME COLOR 1 000 I(A032) 000 I(A033) FRAME COLOR 2 000 I(A034) 000 I(A035) LINE OFFSET 000 I(A036) 000 I(A037) PIXEL OFFSET 000 I(A038) 000 I(A039) VERTICAL START 000 I(A040) 000 I(A041) HORIZONTAL START 000 I(A042) 000 I(A043) NUMBER OF LINES 000 I(A044) 000 I(A045) NUMBER OF LINES 000 I(A046) 000 I(A047) NUMBER OF PIXEL PER LINE 000 I(A048) 000 I(A049) SATURATION OF THE RGB/YC r C b 008 I(A050) 097 I(A051) TINT CONTROL OF THE RGB/YUV 000 I(A052) 000

Setting

value

Setting No. Setting item

I(A053) BRIGHTNESS OF THE RGB/YUV 027 I(A054) 088 I(A055) SOFTMIXER CONTROL 000 I(A056) 240 I(A057) SOFTMIXER CONTROL 000 I(A058) 224 I(A059) ADC RANGE 000 I(A060) 196 I(A061) Standard select 000 I(A062) 033 I(A063) Enable automatic standard I(A064) 127 I(A065) Input select 004 I(A066) 070 I(A067) picture start position 000 I(A068) 000 I(A069) luma/chroma delay adjust 000 I(A070) 000 I(A071) helper delay register 000 I(A072) 000 I(A073) VGA mode select 000 I(A074) 000 I(A075) comb filter control register 000 I(A076) 000 I(A077) comb filter test register 000 I(A078) 000 I(A079) Saturation control 008 I(A080) 022 I(A081) ACC PAL+ Helper gain adjust 000 I(A082) 000 I(A083) ACC multiplier value for PAL+Helper I(A084) 000 I(A085) amplitude killer level 000 I(A086) 015 I(A087) amplitude killer hysteresis 000 I(A088) 005 I(A089) automatic helper disable for I(A090) 000 I(A091) NTSC tint angle 000 I(A092) 000 I(A093) crystal oscillator center frequency I(A094) 000 I(A095) crystal oscillator line-locked mode, I(A096) 000 I(A097) crystal oscillator line-locked mode, I(A098) 144 I(A099) general purpose control bits 000 I(A100) 032 I(A101) scaler mode register 000 I(A102) 000 I(A103) pip control register 000 I(A104) 000

recognition

Signal

nonstandard signals

adjust

lock command

autolock feature

Setting

value

000

001

(No.YA064)1-43

Setting No. Setting item

I(A105) active video length for 1H-FIFO 002 I(A106) 208 I(A107) scaler1 coefficient 006 I(A108) 000 I(A109) scaler2 coefficient 004 I(A110) 000 I(A111) scaler1/2 nonlinear scaling coefficient 000 I(A112) 000 I(A113) scaler1 window controls 000 I(A114) 000 I(A115) scaler1 window controls 000 I(A116) 000 I(A117) scaler1 window controls 000 I(A118) 000 I(A119) scaler1 window controls 000 I(A120) 000 I(A121) scaler1 window controls 000 I(A122) 000 I(A123) scaler2 window controls 000 I(A124) 000 I(A125) scaler2 window controls 000 I(A126) 000 I(A127) scaler2 window controls 000 I(A128) 000 I(A129) scaler2 window controls 000 I(A130) 000 I(A131) scaler2 window controls 000 I(A132) 000 I(A133) brightness register 000 I(A134) 016 I(A135) contrast register 000 I(A136) 048 I(A137) vertical freeze start 015 I(A138) 246 I(A139) vertical freeze stop 000 I(A140) 004 I(A141) 20 bit llc clock center frequency 000 I(A142) 042 I(A143) 20 bit llc clock center frequency 010 I(A144) 171 I(A145) pll frequency limiter 000 I(A146) 054 I(A147) llc clock generator control word 000 I(A148) 005

Setting

value

Setting No. Setting item

IB : CXA3506R

I(B01) VCODIV1 n, m(L) 024 I(B02) VCODIV2 m(H) 035 I(B03) DELAY 027 I(B04) Charge Punp 018 I(B05) POLARITY 038 I(B06) SYNC 029 I(B07) TTLOUT ENABLE 127 I(B08) MAIN CONTRAST 078 I(B09) SUB CONTRAST G(Y) 128 I(B10) SUB CONTRAST B(Cb) 128 I(B11) SUB CONTRAST R(Cr) 128 I(B12) SUB BRIGHTNESS G(Y) 128 I(B13) SUB BRIGHTNESS B 128 I(B14) SUB BRIGHTNESS R 128 I(B15) Cb OFFSET 032 I(B16) Cr OFFSET 032 I(B17) AMP MODE 004 I(B18) SYNC SEP 000 I(B19) OUTPUT MODE 000 I(B20) POWER SAVE 048

IC : TA1318

I(C01) Hfreq,HD1/VD1sw,HD2/

VD2sw,SepaLVL

I(C02) DAC1,DAC2,DAC3,test,HD1inv,

HD2inv

I(C03) Vfreq,CLPphase,FREQ DET

SW,INPUTsw

I(C04) HDphase,VD1inv,VD2inv 129

Setting

value

061

167

192

1-44 (No.YA064)

Setting No. Setting item

ID : PEMBRANDT-I

I(D001) OUTPUT CONTROL 001 I(D002) CONFIG 000 I(D003) ADDR CLEAR 0 063 I(D004) ADDR CLEAR_1 255 I(D005) LOAD SHADOW 000 I(D006) IRQ SOURCE 000 I(D007) IRQ MASK 000 I(D008) IRQ CLEAR 001 I(D009) FLAGS 000 I(D010) FLAGS CLEAR 001 I(D011) GP OUTPUT 000 I(D012) STATUS1 000 I(D013) STATUS2 000 I(D014) MPLL MDIV L 002 I(D015) MPLL MDIV H 000 I(D016) MPLL NDIV 000 I(D017) PPLL MDIV_L 002 I(D018) PPLL MDIV_H 000 I(D019) PPLL NDIV 000 I(D020) OPLL MDIV L 229 I(D021) OPLL MDIV H 000 I(D022) OPLL NDIV 255 I(D023) NL CONTROL 005 I(D024) NL SWITCH 000 I(D025) NL X 000 I(D026) NL Y 000 I(D027) VIDEO CONFIG 008 I(D028) VIDEO SC 008 I(D029) VIN POLARITY 000 I(D030) VIN CONTROL 000 I(D031) VIN ACTIVE PIXELS L 000 I(D032) VIN ACTIVE LINES L 000 I(D033) VIN FLAGGED LINE 000 I(D034) VIN REGS MSBITS 000 I(D035) VIN FILTER GRP/C0 000 I(D036) VIN FILTER GRP/ C1 000 I(D037) VIN FILTER GRP/C2 000 I(D038) VIN FILTER GRP/C3 000 I(D039) VIN FILTER GRP/C4 064 I(D040) VIN FILTER GRP/C5 000 I(D041) VIN FILTER GRP/C6 000 I(D042) VIN FILTER GRP/C7 000 I(D043) VIN FILTER GRP/C8 000 I(D044) VOUT FILTER GRP/C0 253 I(D045) VOUT FILTER GRP/C1 250 I(D046) VOUT FILTER GRP/ C2 253 I(D047) VOUT FILTER GRP/ C3 250 I(D048) VOUT FILTER GRP/ C4 100 I(D049) VOUT FILTER GRP/C5 250 I(D050) VOUT FILTER GRP/C6 253 I(D051) VOUT FILTER GRP/C7 250 I(D052) VOUT FILTER GRP/C8 253 I(D053) N/A 000 I(D054) N/A 000

Setting

value

Setting No. Setting item

I(D055) VDSCALER TOUTX L 208 I(D056) VDSCALER TOUTX H 002 I(D057) VDSCALER CONTROL 000 I(D058) VDSCALER DELTAX L 000 I(D059) VDSCALER DELTAX H 008 I(D060) VDSCALER DELTAY L 000 I(D061) VDSCALER DELTAY H 008 I(D062) VDSCALER Y0 000 I(D063) VDSCALER X0 000 I(D064) VDSCALER TOUTY L 224 I(D065) VDSCALER TOUTY H 001 I(D066) VUSCALER CONTROL 000 I(D067) VUSCALER DELTAX L 192 I(D068) VUSCALER DELTAX H 006 I(D069) VUSCALER DELTAY L 000 I(D070) VUSCALER DELTAY H 008 I(D071) VUSCALER Y0 000 I(D072) VUSCALER X0 000 I(D073) DI CONTROL 004 I(D074) DI C0 031 I(D075) DI C1 007 I(D076) DI C2 127 I(D077) DI C3 255 I(D078) DI C4 031 I(D079) DATA CONFIG 000 I(D080) DATA SC 008 I(D081) DIN POLARITY 0 041 I(D082) DIN POLARITY 1 000 I(D083) DIN CONTROL 0 004 I(D084) DIN CONTROL 1 064 I(D085) DIN CONTROL 2 002 I(D086) DPLL DIV L 000 I(D087) DPLL DIV H 000 I(D088) DIN THRESHOLD 008 I(D089) CLAMP START 001 I(D090) CLAMP WIDTH 016 I(D091) DIN LINE TRIG 001 I(D092) DIN PIXEL TRIG 001 I(D093) ACTIVE LINE START L 038 I(D094) ACTIVE LINE START H 000 I(D095) ACTIVE LINES L 224 I(D096) ACTIVE LINES H 001 I(D097) ACTIVE PIXEL START L 132 I(D098) ACTIVE PIXEL START H 000 I(D099) ACTIVE PIXELS L 128 I(D100) ACTIVE PIXELS H 002 I(D101) DIN FLAGGED LINE L 000 I(D102) DIN FLAGGED LINE H 000 I(D103) DIN CONTROL 3 006 I(D104) N/A 000 I(D105) N/A 000 I(D106) N/A 000 I(D107) DIN FILTER GRP/C0 253 I(D108) DIN FILTER GRP/C1 250 I(D109) DIN FILTER GRP/C2 253

Setting

value

(No.YA064)1-45

Setting No. Setting item

I(D110) DIN FILTER GRP/C3 250 I(D111) DIN FILTER GRP/C4 100 I(D112) DIN FILTER GRP/C5 250 I(D113) DIN FILTER GRP/C6 253 I(D114) DIN FILTER GRP/C7 250 I(D115) DIN FILTER GRP/C8 253 I(D116) DDSCALER TOUTX L 128 I(D117) DDSCALER TOUTX H 002 I(D118) DDSCALER CONTROL 000 I(D119) DDSCALER DELTAX L 000 I(D120) DDSCALER DELTAX H 008 I(D121) DDSCALER DELTAY L 000 I(D122) DDSCALER DELTAY H 008 I(D123) N/A 000 I(D124) N/A 000 I(D125) DDSCALER TOUTY L 224 I(D126) DDSCALER TOUTY H 001 I(D127) DUSCALER CONTROL 000 I(D128) DUSCALER DELTAX L 000 I(D129) DUSCALER DELTAX H 006 I(D130) DUSCALER DELTAY L 000 I(D131) DUSCALER DELTAY H 008 I(D132) DUSCALER Y0 001 I(D133) DUSCALER X0 001 I(D134) VIDEO WIN GRP/Y POS L 001 I(D135) VIDEO WIN GRP/Y POS H 000 I(D136) VIDEO WIN GRP/Y SIZE L 224 I(D137) VIDEO WIN GRP/Y SIZE H 001 I(D138) VIDEO WIN GRP/X POS L 001 I(D139) VIDEO WIN GRP/X POS H 000 I(D140) VIDEO WIN GRP/X SIZE L 085 I(D141) VIDEO WIN GRP/X SIZE H 003 I(D142) DATA WIN GRP/Y POS L 001 I(D143) DATA WIN GRP/Y POS H 000 I(D144) DATA WIN GRP/Y SIZE L 224 I(D145) DATA WIN GRP/Y SIZE H 001 I(D146) DATA WIN GRP/X POS L 001 I(D147) DATA WIN GRP/X POS H 000 I(D148) DATA WIN GRP/X SIZE L 085 I(D149) DATA WIN GRP/X SIZE H 003 I(D150) OSDA WIN GRP/Y POS L 000 I(D151) OSDA WIN GRP/Y POS H 000 I(D152) OSDA WIN GRP/Y SIZE L 000 I(D153) OSDA WIN GRP/Y SIZE H 000 I(D154) OSDA WIN GRP/X POS L 000 I(D155) OSDA WIN GRP/X POS H 000 I(D156) OSDA WIN GRP/X SIZE L 000 I(D157) OSDA WIN GRP/X SIZE H 000 I(D158) OSDB WIN GRP/Y POS L 000 I(D159) OSDB WIN GRP/Y POS H 000 I(D160) OSDB WIN GRP/Y SIZE L 000 I(D161) OSDB WIN GRP/Y SIZE H 000 I(D162) OSDB WIN GRP/X POS L 000 I(D163) OSDB WIN GRP/X POS H 000 I(D164) OSDB WIN GRP/X SIZE L 000

Setting

value

Setting No. Setting item

I(D165) OSDB WIN GRP/X SIZE H 000 I(D166) LUT Y 000 I(D167) LUT U 000 I(D168) LUT V 000 I(D169) LUT R L 000 I(D170) LUT R H 000 I(D171) LUT G L 000 I(D172) LUT G H 000 I(D173) LUT B L 000 I(D174) LUT B H 000 I(D175) PALETTE R 000 I(D176) PALETTE G 000 I(D177) PALETTE B 000 I(D178) VIDEO CSC BIAS 000 I(D179) VIDEO CSC GRP/C(0) L 154 I(D180) VIDEO CSC GRP/C(0) H 003 I(D181) VIDEO CSC GRP/C(1) L 000 I(D182) VIDEO CSC GRP/C(1) H 000 I(D183) VIDEO CSC GRP/C(2) L 170 I(D184) VIDEO CSC GRP/C(2) H 001 I(D185) VIDEO CSC GRP/C(3) L 154 I(D186) VIDEO CSC GRP/C(3) H 003 I(D187) VIDEO CSC GRP/C(4) L 184 I(D188) VIDEO CSC GRP/C(4) H 255 I(D189) VIDEO CSC GRP/C(5) L 086 I(D190) VIDEO CSC GRP/C(5) H 255 I(D191) VIDEO CSC GRP/C(6) L 154 I(D192) VIDEO CSC GRP/C(6) H 003 I(D193) VIDEO CSC GRP/C(7) L 153 I(D194) VIDEO CSC GRP/C(7) H 001 I(D195) VIDEO CSC GRP/C(8) L 000 I(D196) VIDEO CSC GRP/C(8) H 000 I(D197) DATA CSC BIAS 000 I(D198) DATA CSC GRP/C(0) L 154 I(D199) DATA CSC GRP/C(0) H 003 I(D200) DATA CSC GRP/C(1) L 000 I(D201) DATA CSC GRP/C(1) H 000 I(D202) DATA CSC GRP/C(2) L 223 I(D203) DATA CSC GRP/C(2) H 001 I(D204) DATA CSC GRP/C(3) L 154 I(D205) DATA CSC GRP/C(3) H 003 I(D206) DATA CSC GRP/C(4) L 217 I(D207) DATA CSC GRP/C(4) H 255 I(D208) DATA CSC GRP/C(5) L 145 I(D209) DATA CSC GRP/C(5) H 255 I(D210) DATA CSC GRP/C(6) L 154 I(D211) DATA CSC GRP/C(6) H 003 I(D212) DATA CSC GRP/C(7) L 172 I(D213) DATA CSC GRP/C(7) H 001 I(D214) DATA CSC GRP/C(8) L 000 I(D215) DATA CSC GRP/C(8) H 000 I(D216) OUT CONFIG 012 I(D217) BACKGND GRP/BLUE 000 I(D218) BACKGND GRP/GREEN 000 I(D219) BACKGRND GRP/RED 000

Setting

value

1-46 (No.YA064)

Setting No. Setting item

I(D220) OSDA CONTROL 000 I(D221) KEYSTONE CONTROL 000 I(D222) KEYSTONE CONTROL 000 I(D223) KEYSTONE LINES 255 I(D224) DITHER CONTROL 042 I(D225) DITHER C0 060 I(D226) DITHER C1 056 I(D227) DISPLAY CONTROL 0 032 I(D228) DISPLAY CONTROL 1 000 I(D229) DISPLAY CONTROL 2 003 I(D230) D/F GRP/VSYNC CYCLE L 247 I(D231) D/F GRP/VSYNC CYCLE H 001 I(D232) D/F GRP/HSYNC CYCLE L 128 I(D233) D/F GRP/HSYNC CYCLE H 003 I(D234) D/F GRP/VSYNC WIDTH 004 I(D235) D/F GRP/VSYNC OFFSET H 000 I(D236) D/F GRP/HSYNC WIDTH L 010 I(D237) D/F GRP/HSYNC WIDTH H 000 I(D238) D/F GRP/ACT LINE START L 015 I(D239) D/F GRP/ACT LINE START H 000 I(D240) D/F GRP/ACT LINES L 224 I(D241) D/F GRP/ACT LINES H 001 I(D242) D/F GRP/ACT PIX START L 037 I(D243) D/F GRP/ACT PIX START H 000 I(D244) D/F GRP/ACT PIXS L 084 I(D245) D/F GRP/ACT PIXS H 003 I(D246) DISPLAY HV DELAY 0 001 I(D247) DISPLAY HV DELAY 1 001 I(D248) DISPLAY POLARITY 003 I(D249) CONTROL 3D 000 I(D250) X0 3D 000 I(D251) SECT STAT GRP/VIDEO0 L 000 I(D252) SECT STAT GRP/VIDEO0 H 000 I(D253) SECT STAT GRP/VIDEO1 L 180 I(D254) SECT STAT GRP/VIDEO1 H 000 I(D255) SECT STAT GRP/VIDEO2 L 104 I(D256) SECT STAT GRP/VIDEO2 H 001 I(D257) SECT STAT GRP/LDAT0 L 028 I(D258) SECT STAT GRP/LDAT0 H 002 I(D259) SECT STAT GRP/RDAT0 L 112 I(D260) SECT STAT GRP/RDAT0 H 003 I(D261) SECT STAT GRP/LDAT1 L 196 I(D262) SECT STAT GRP/LDAT1 H 004 I(D263) SECT STAT GRP/RDAT1 L 024 I(D264) SECT STAT GRP/RDAT1 H 006 I(D265) SECT STAT GRP/OSD0 L 000 I(D266) SECT STAT GRP/OSD0 H 000 I(D267) SECT STAT GRP/OSD1 L 000 I(D268) SECT STAT GRP/OSD1 H 000 I(D269) SECT STAT GRP/OSD2 L 000 I(D270) SECT STAT GRP/OSD2 H 000 I(D271) SECT STAT GRP/OSD3 L 000 I(D272) SECT STAT GRP/OSD3 H 000 I(D273) S/S GRP/IDATA OFFSET L 000 I(D274) S/S GRP/IDATA OFFSET H 000

Setting

value

Setting No. Setting item

I(D275) LINE LENG GRP/VIDEO L 144 I(D276) LINE LENG GRP/VIDEO H 000 I(D277) LINE LENG GRP/DATA L 032 I(D278) LINE LENG GRP/DATA H 001 I(D279) LINE LENG GRP/IDATA L 000 I(D280) LINE LENG GRP/IDATA H 000 I(D281) LINE LENG GRP/OSD0 L 000 I(D282) LINE LENG GRP/OSD0 H 000 I(D283) LINE LENG GRP/OSD1 L 000 I(D284) LINE LENG GRP/OSD1 H 000 I(D285) LINE LENG GRP/OSD2 L 000 I(D286) LINE LENG GRP/OSD2 H 000 I(D287) LINE LENG GRP/OSD3 L 000 I(D288) LINE LENG GRP/OSD3 H 000 I(D289) WIN LINE OFFSET GRP/VIDEO L 000 I(D290) WIN LINE OFFSET GRP/VIDEO H 000 I(D291) WIN LINE OFFSET GRP/DATA L 000 I(D292) WIN LINE OFFSET GRP/DATA H 000 I(D293) WIN LINE OFFSET GRP/OSDA L 000 I(D294) WIN LINE OFFSET GRP/OSDA H 000 I(D295) WIN LINE OFFSET GRP/OSDB L 000 I(D296) WIN LINE OFFSET GRP/OSDB H 000 I(D297) WIN DELAY GRP/VIDEO L 000 I(D298) WIN DELAY GRP/VIDEO H 000 I(D299) WIN DELAY GRP/DATA L 000 I(D300) WIN DELAY GRP/DATA H 000 I(D301) WIN DELAY GRP/OSDA L 000 I(D302) WIN DELAY GRP/OSDA H 000 I(D303) WIN DELAY GRP/OSDB L 000 I(D304) WIN DELAY GRP/OSDB H 000 I(D305) WIN LENG GRP/VIDEO L 208 I(D306) WIN LENG GRP/VIDEO H 002 I(D307) WIN LENG GRP/DATA L 000 I(D308) WIN LENG GRP/DATA H 000 I(D309) WIN LENG GRP/OSDA L 000 I(D310) WIN LENG GRP/OSDA H 000 I(D311) WIN LENG GRP/OSDB L 000 I(D312) WIN LENG GRP/OSDB H 000 I(D313) SC THRESHOLD GRP/VIDEO IN 064 I(D314) SC THRESHOLD GRP/VIDEO OUT 064 I(D315) SC THRESHOLD GRP/DATA IN 032 I(D316) SC THRESHOLD GRP/DATA OUT 032 I(D317) OSD IN ADDR L 000 I(D318) OSD IN ADDR R 000 I(D319) OSD IN BLOCK LENGTH 000 I(D320) OSD SECTIONS 000 I(D321) OSD IN DATA 000 I(D322) OSD IN CONTROL 000 I(D323) SDRAM WINDOW CONTROL 003 I(D324) SDRAM INIT 000 I(D325) MSR AOI GRP/LINE START L 000 I(D326) MSR AOI GRP/LINE START H 000 I(D327) MSR AOI GRP/LINE END L 000 I(D328) MSR AOI GRP/LINE END H 000 I(D329) MSR AOI GRP/PIXEL START L 000

Setting

value

(No.YA064)1-47

Setting No. Setting item

I(D330) MSR AOI GRP/PIXEL START H 000 I(D331) MSR AOI GRP/PIXEL END L 000 I(D332) MSR AOI GRP/PIXEL END H 000 I(D333) MSR CONTROL 072 I(D334) MSR ENABLE 001 I(D335) MSR COMMANDS 000 I(D336) MSR STATUS 000 I(D337) MSR HV PARAMETERS

GRP/HSYNC WIDTH L

I(D338) MSR HV PARAMETERS

GRP/HSYNC WIDTH H

I(D339) MSR HV PARAMETERS

GRP/HSYNC CYCLE L

I(D340) MSR HV PARAMETERS

GRP/HSYNC CYCLE H

I(D341) MSR HV PARAMETERS

GRP/VSYNC WIDTH L

I(D342) MSR HV PARAMETERS

GRP/VSYNC WIDTH H

I(D343) MSR HV PARAMETERS

GRP/VSYNC CYCLE L

I(D344) MSR HV PARAMETERS

GRP/VSYNC CYCLE H

I(D345) MSR HV PARAMETERS

GRP/HV DELAY L

I(D346) MSR HV PARAMETERS

GRP/HV DELAY H

I(D347) MSR ACTIVE REGION

GRP/LINE START L

I(D348) MSR ACTIVE REGION

GRP/LINE START H

I(D349) MSR ACTIVE REGION

GRP/LINE END L

I(D350) MSR ACTIVE REGION

GRP/LINE END H

I(D351) MSR ACTIVE REGION

GRP/PIXEL START L

I(D352) MSR ACTIVE REGION

GRP/PIXEL START H

I(D353) MSR ACTIVE REGION

GRP/PIXEL END L

I(D354) MSR ACTIVE REGION

GRP/PIXEL END H I(D355) MSR YMIN 000 I(D356) MSR YMAX 000

IE : PDP I / F

I(E01) DITHER 008 I(E02) Not use 000 I(E03) Not use 008 I(E04) Not use 000 I(E05) Not use 000 I(E06) Not use 000 I(E07) bit INVERT 000 I(E08) WT BAL OFFSET G 000 I(E09) WT BAL OFFSET B 000 I(E10) WT BAL OFFSET R 000 I(E11) WT BAL ADJ 000 I(E12) TEST MODE BRIGHT 128

Setting

value

000

Setting No. Setting item

I(E13) BK LEVEL ADJ 010 I(E14) GAIN LEVEL ADJ 165 I(E15) WT BAL GAIN ADJ G 255 I(E16) WT BAL GAIN ADJ B 255 I(E17) WT BAL GAIN ADJ R 255 I(E18) GUMMER 000

IF : PDP MODULE

I(F01) Pattern Select 001 I(F02) Not use 000 I(F03) Data Level 255 I(F04) Not use 000 I(F05) Not use 000 I(F06) Brightness R 000 I(F07) Not use 000 I(F08) Brightness G 000 I(F09) Not use 000 I(F10) Brightness B 000 I(F11) Internal Gamma Enable 001 I(F12) GTS Function Enable 001 I(F13) Not use 128 I(F14) Not use 128 I(F15) Not use 128 I(F16) Not use 000 I(F17) Error-Diffusion 004 I(F18) Not use 000 I(F19) External APC Enable H 000 I(F20) External APC Enable V 085 I(F21) Not use 000 I(F22) Not use 000 I(F23) Internal Pattern Enable 000 I(F24) Not use 000 I(F25) Pattern Select 001 I(F26) Not use 000 I(F27) Data Level 255 I(F28) Not use 000 I(F29) Not use 000 I(F30) Brightness R 000 I(F31) Not use 000 I(F32) Brightness G 000 I(F33) Not use 000 I(F34) Bribhtness B 000 I(F35) Internal Gamma Enable 001 I(F36) GTS Function Enable 001 I(F37) Not use 128 I(F38) Not use 128 I(F39) Not use 128 I(F40) Not use 000 I(F41) Error-Diffusion 004 I(F42) Not use 000 I(F43) External APC Enable H 000 I(F44) External APC Enable V 085 I(F45) Not use 000 I(F46) Not use 000 I(F47) Internal Pattern Enable 000 I(F48) Not use 000

Setting

value

1-48 (No.YA064)

Setting No. Setting item

IG : UPD64083GF

I(G01) SYSTEM SETTING 021 I(G02) CLOCK CONTROL 000 I(G03) DYCO PIN CONTROL 193 I(G04) CLP WIDTH/YC DELAY 034 I(G05) DY CORING 042 I(G06) DC CORING 036 I(G07) NR CONTROL 034 I(G08) ID1 ENABLE 001 I(G09) CORING LEVEL 086 I(G10) ID1 CONTROL 072 I(G11) VERTICAL APARTURE 043 I(G12) Y PEAKING 011

Setting

value

Setting No. Setting item

I(G13) LINE-COMB CONTROL 241 I(G14) DY SENSITIVITY 037 I(G15) Not use 008 I(G16) Not use 068 I(G17) YH CONTROL 112 I(G18) TEST REGISTER 008 I(G19) PLL CONTROL 051 I(G20) SYNC SLICE 200 I(G21) BGP CONTROL 074 I(G22) ADC CONTROL 236 I(G23) SYSTEM POWERDOWN 000 I(G24) TEST REGISTER 008

Setting

value

(No.YA064)1-49

 ENHACER BLOCK

Setting No. Setting item

EA : SHARPNESS A=-3

E(A01) FILTER COEFF C0 000 E(A02) FILTER COEFF C1 000 E(A03) FILTER COEFF C2 000 E(A04) FILTER COEFF C3 000 E(A05) FILTER COEFF C4 064 E(A06) FILTER COEFF C5 000 E(A07) FILTER COEFF C6 000 E(A08) FILTER COEFF C7 000 E(A09) FILTER COEFF C8 000

EB : SHARPNESS A=-2

E(B01) FILTER COEFF C0 -001 E(B02) FILTER COEFF C1 -002 E(B03) FILTER COEFF C2 -001 E(B04) FILTER COEFF C3 -002 E(B05) FILTER COEFF C4 076 E(B06) FILTER COEFF C5 -002 E(B07) FILTER COEFF C6 -001 E(B08) FILTER COEFF C7 -002 E(B09) FILTER COEFF C8 -001

EC : SHARPNESS A=-1

E(C01) FILTER COEFF C0 -002 E(C02) FILTER COEFF C1 -004 E(C03) FILTER COEFF C2 -002 E(C04) FILTER COEFF C3 -004 E(C05) FILTER COEFF C4 088 E(C06) FILTER COEFF C5 -004 E(C07) FILTER COEFF C6 -002 E(C08) FILTER COEFF C7 -004 E(C09) FILTER COEFF C8 -002

ED : SHARPNESS A=0

E(D01) FILTER COEFF C0 -003 E(D02) FILTER COEFF C1 -006 E(D03) FILTER COEFF C2 -003 E(D04) FILTER COEFF C3 -006 E(D05) FILTER COEFF C4 100 E(D06) FILTER COEFF C5 -006 E(D07) FILTER COEFF C6 -003 E(D08) FILTER COEFF C7 -006 E(D09) FILTER COEFF C8 -003

EE : SHARPNESS A=+1

E(E01) FILTER COEFF C0 -004 E(E02) FILTER COEFF C1 -008 E(E03) FILTER COEFF C2 -004 E(E04) FILTER COEFF C3 -008 E(E05) FILTER COEFF C4 112 E(E06) FILTER COEFF C5 -008 E(E07) FILTER COEFF C6 -004 E(E08) FILTER COEFF C7 -008 E(E09) FILTER COEFF C8 -004

Setting

value

Setting No. Setting item

EF : SHARPNESS A=+2

E(F01) FILTER COEFF C0 -005 E(F02) FILTER COEFF C1 -010 E(F03) FILTER COEFF C2 -005 E(F04) FILTER COEFF C3 -010 E(F05) FILTER COEFF C4 124 E(F06) FILTER COEFF C5 -010 E(F07) FILTER COEFF C6 -005 E(F08) FILTER COEFF C7 -010 E(F09) FILTER COEFF C8 -005

EG : SHARPNESS A=+3

E(G01) FILTER COEFF C0 -010 E(G02) FILTER COEFF C1 -004 E(G03) FILTER COEFF C2 -010 E(G04) FILTER COEFF C3 -008 E(G05) FILTER COEFF C4 127 E(G06) FILTER COEFF C5 -008 E(G07) FILTER COEFF C6 -010 E(G08) FILTER COEFF C7 -004 E(G09) FILTER COEFF C8 -010

EH : SHARPNESS A=+4

E(H01) FILTER COEFF C0 -012 E(H02) FILTER COEFF C1 000 E(H03) FILTER COEFF C2 -012 E(H04) FILTER COEFF C3 -008 E(H05) FILTER COEFF C4 127 E(H06) FILTER COEFF C5 -008 E(H07) FILTER COEFF C6 -012 E(H08) FILTER COEFF C7 000 E(H09) FILTER COEFF C8 -012

EI : SHARPNESS B=-3

E(I01) FILTER COEFF C0 001 E(I02) FILTER COEFF C1 001 E(I03) FILTER COEFF C2 001 E(I04) FILTER COEFF C3 -002 E(I05) FILTER COEFF C4 062 E(I06) FILTER COEFF C5 -002 E(I07) FILTER COEFF C6 001 E(I08) FILTER COEFF C7 001 E(I09) FILTER COEFF C8 001

EJ : SHARPNESS B=-2

E(J01) FILTER COEFF C0 001 E(J02) FILTER COEFF C1 -001 E(J03) FILTER COEFF C2 001 E(J04) FILTER COEFF C3 -003 E(J05) FILTER COEFF C4 068 E(J06) FILTER COEFF C5 -003 E(J07) FILTER COEFF C6 001 E(J08) FILTER COEFF C7 -001 E(J09) FILTER COEFF C8 001

Setting

value

1-50 (No.YA064)

Setting No. Setting item

EK : SHARPNESS B=-1

E(K01) FILTER COEFF C0 000 E(K02) FILTER COEFF C1 000 E(K03) FILTER COEFF C2 000 E(K04) FILTER COEFF C3 -005 E(K05) FILTER COEFF C4 074 E(K06) FILTER COEFF C5 -005 E(K07) FILTER COEFF C6 000 E(K08) FILTER COEFF C7 000 E(K09) FILTER COEFF C8 000

EL : SHARPNESS B=0

E(L01) FILTER COEFF C0 000 E(L02) FILTER COEFF C1 -001 E(L03) FILTER COEFF C2 000 E(L04) FILTER COEFF C3 -007 E(L05) FILTER COEFF C4 080 E(L06) FILTER COEFF C5 -007 E(L07) FILTER COEFF C6 000 E(L08) FILTER COEFF C7 -001 E(L09) FILTER COEFF C8 000

EM : SHARPNESS B=+1

E(M01) FILTER COEFF C0 -001 E(M02) FILTER COEFF C1 -002 E(M03) FILTER COEFF C2 -001 E(M04) FILTER COEFF C3 -008 E(M05) FILTER COEFF C4 080 E(M06) FILTER COEFF C5 -008 E(M07) FILTER COEFF C6 -001 E(M08) FILTER COEFF C7 -002 E(M09) FILTER COEFF C8 -001

Setting

value

Setting No. Setting item

EN : SHARPNESS B=+2

E(N01) FILTER COEFF C0 -001 E(N02) FILTER COEFF C1 -004 E(N03) FILTER COEFF C2 -001 E(N04) FILTER COEFF C3 -009 E(N05) FILTER COEFF C4 094 E(N06) FILTER COEFF C5 -009 E(N07) FILTER COEFF C6 -001 E(N08) FILTER COEFF C7 -004 E(N09) FILTER COEFF C8 -001

EO : SHARPNESS B=+3

E(O01) FILTER COEFF C0 -002 E(O02) FILTER COEFF C1 -005 E(O03) FILTER COEFF C2 -002 E(O04) FILTER COEFF C3 -009 E(O05) FILTER COEFF C4 100 E(O06) FILTER COEFF C5 -009 E(O07) FILTER COEFF C6 -002 E(O08) FILTER COEFF C7 -005 E(O09) FILTER COEFF C8 -002

EP : SHARPNESS B=+4

E(P01) FILTER COEFF C0 -003 E(P02) FILTER COEFF C1 -005 E(P03) FILTER COEFF C2 -003 E(P04) FILTER COEFF C3 -012 E(P05) FILTER COEFF C4 110 E(P06) FILTER COEFF C5 -012 E(P07) FILTER COEFF C6 -003 E(P08) FILTER COEFF C7 -005 E(P09) FILTER COEFF C8 -003

Setting

value

(No.YA064)1-51

4.6 ADJUSTMENT PROCEDURE

Item

PDP POWER SUPPLY VOLTAGE

NTSC

Va

XX XX XX XX XX

Measuring instrument

DC voltmeter Va

VOLTAGE LABEL

NTSC/PAL

Ve VsetVsc Vs

Test point Adjustment part Description

Vsca Vs Ve Vset [SMPS PWB]

VA VR VSCAN VR VS VR VE VR VSET VR [SMPS PWB]

• After turning the power on, confirm that "NO SYNC" is displayed.

• Start making adjustment five minutes or later after turning the power on. (1) Connect the DC voltmeter to test points Va, Vsca,

Vs, Ve, and Vset, and GND on SMPS PWB.

(2) Adjust VA VR, VSCAN VR, VS VR, VE VR, and

VSET respectively so that their voltage becomes the value in the voltage label attached to the panel.

VOLTAGE ADJUSTMENT POINT

VS

Vs

Vsca

L

Vset

Va

SMPS PWB

Ve

VE

VIDEO DECODER VCO

Remote control unit

Signal generator

[VCO ADJUST PROGRAM]

VSCANVSET

VA

: Adjustment VR : Test point

(1) Input an NTSC colour bar signal from VIDEO A

terminal.

(2) Enter the SERVICE MODE, and select "VCO

ADJUST".

(3) Select "YES" and press the [] key. Adjustment is

performed automatically.

(4) After a few seconds, confirm that "ADJUSTMENT

OK" is displayed on the screen.

(5) Turn the power off. Then, turn the power on again,

and confirm that the colour bar signal is properly displayed.

1-52 (No.YA064)

Item

A-D INPUT OFFSET (480i)

Offset values

too low

Sate of an

optimum

adjustment

Offset values

too hight

Measuring

instrument

Remote control unit

Signal generator

Oscilloscope

Horizontal duration

Picture signal duration

Increase the value

Decrease the value

Test point Adjustment part Description

TP-PR TP-PB [MAIN PWB]

[DEVICE INITIAL BLOCK] I (B19) : Test mode

(1) Input a 480i whole black signal from COMPONENT

terminal. (2) Connect the oscilloscope to TP-PR. (3) Enter the SERVICE MODE, and select "DEVICE

[WHITE BALANCE BLOCK] W(E11) : AD offset R W(E13) : AD offset B

INITIAL VALUE". (4) Select IB : CXA3506R. (5) Select < I(B19) > (Test mode), and change the

setting value from 000 to 001 to 000. (6) Return to the SERVICE MODE, and select "WHITE

BALANCE BLOCK". (7) Select WE : COMPO 15k HIGH.

3.3V

(8) Select < W(E11) > (AD offset R). As is shown in the

left figure, adjust the setting value of < W(E11) > so

that Low(0V) voltage is as bright as High(3.3V)

0V

voltage in the scanning interval. Adjust the setting

value of < W(E11) > within 2-3 points from the initial

value.

3.3V

(9) Connect the oscilloscope to TP-PB.

(10) Select < W(E13) > (AD offset B) of WHITE BALANCE

BLOCK, and adjust the setting value of < W(E13) > so

0V

3.3V

0V

that Low(0V) image signal voltage is as bright as

High(3.3V) voltage in the same way as for < W(E11) >.

A-D INPUT OFFSET (1080i)

Remote control unit

Signal generator

Oscilloscope

TP-PR TP-PB [MAIN PWB]

[DEVICE INITIAL BLOCK] I (B19) : Test mode

[WHITE BALANCE BLOCK] W(G11) : AD offset R W(G13) : AD offset B

(1) Input a 1080i whole black signal from COMPONENT

terminal. (2) Enter the SERVICE MODE, and select "WHITE

BALANCE BLOCK". (3) Select WG : COMPO HIGH. (4) Select < W(G11) > (AD offset R), and adjust in the

same way as for the 480i signal above. (5) Select < W(G13) > (AD offset B), and adjust in the

same way as for the 480i signal above.

(No.YA064)1-53

Item

RGB OFFSET (NTSC)

Measuring instrument

Test point Adjustment part Description

Remote control unit

Signal generator

(RAMP pattern)

Align the 3 lines on the left part

[CPU BLOCK] C(H01) : Test mode

[WHITE BALANCE BLOCK] W(C04) : R cutoff W(C06) : B cutoff

(1) Input an NTSC lamp pattern signal from VIDEO A

terminal.

(2) Enter the SERVICE MODE, and select "CPU

BLOCK". (3) Select CH : Test mode. (4) Select < C(H01) > (Test mode), and change "0" into

"2", and then enter "RGB BALANCE Test mode". (5) Return to the MAIN MENU screen. (6) Select "WHITE BALANCE BLOCK". (7) Select "WC : VIDEO HIGH". (8) Select < W(C04) > (R cutoff) and < W(C06) > (B

cutoff), and adjust the setting values so that the three

lines on the left of the lamp pattern screen are lined

in the same line (so that there is no colour zone in

the border between white and black).

∗ Don't change W(C05) : G cutoff value.

(9) After the adjustment finishes, select < C(H01) > of

"CPU BLOCK" again, and return the setting value "2"

to "0".

RGB OFFSET (480i)

RGB OFFSET (1080i)

RGB OFFSET (VGA)

RGB OFFSET (RGB15k)

Remote control unit

Signal generator

Remote control unit

Signal generator

Remote control unit

Signal generator

Remote control unit

Signal generator

[CPU BLOCK] C(H01) : Test mode

[WHITE BALANCE BLOCK] W(E04) : R cutoff W(E06) : B cutoff

[CPU BLOCK] C(H01) : Test mode

[WHITE BALANCE BLOCK] W(G04) : R cutoff W(G06) : B cutoff

[CPU BLOCK] C(H01) : Test mode

[WHITE BALANCE BLOCK] W(A04) : R cutoff W(A06) : B cutoff

[CPU BLOCK] C(H01) : Test mode

[WHITE BALANCE BLOCK] W( I 04) : R cutoff W( I 06) : B cutoff

(1) Input a 480i lamp pattern signal from COMPONENT

terminal. (2) Select "WE : COMPO.15k HIGH". (3) Adjust < W(E04) > (R cutoff) and < W(E06) > (B

cutoff) in the same way as for NTSC.

(1) Input a 1080i lamp pattern signal from

COMPONENT terminal. (2) Select "WG : COMPO. HIGH". (3) Adjust < W(G04) > (R cutoff) and < W(G06) > (B

cutoff) in the same way as for NTSC.

(1) Input a VGA(640 × 480 dots) lamp pattern signal

from PC terminal. (2) Select "WA : RGB PC HIGH". (3) Adjust < W(A04) > (R cutoff) and < W(A06) > (B

cutoff) in the same way as for NTSC.

(1) Input an RGB15k lamp pattern signal from PC input

terminal. (2) Select "W I : RGB 15k HIGH". (3) Adjust < W(I 04) > (R cutoff) and < W(I 06) > (B

cutoff) in the same way as for NTSC.

1-54 (No.YA064)

Item

WHITE BALANCE (NTSC)

WHITE BALANCE (480i)

WHITE BALANCE (1080i)

Measuring

instrument

Remote control unit

Signal generator

Colour analyzer

COLOUR

TEMP.

HIGH

LOW

Remote control unit

Signal generator

Colour analyzer

Remote control unit

Signal generator

Colour analyzer

Test point Adjustment part Description

[WHITE BALANCE BLOCK] (Colour temperature : HIGH) W(C01) : R drive W(C02) : G drive W(C03) : B drive

• Keep the set running for twenty minutes or longer. If you turn the set on again, make adjustment 5 minutes or later after you turn the set on.

• Set PICTURE ADJ. of MAIN MENU to the initial state.

(1) Input an NTSC window pattern (brilliance 70%)

signal from VIDEO A terminal.

(2) Set COLOUR TEMP at HIGH in FUNCTION

SELECT of < MAIN MENU >. (Colour temperature : LOW) W(D01) : R drive W(D02) : G drive W(D03) : B drive

(3) Enter the SERVICE MODE. (4) Select "WHITE BALANCE BLOCK". (5) Select "WC : VIDEO HIGH". (6) Select < W(C01) > (R drive) and < W(C03) > (B

drive).

(7) Adjust < W(C01) > and < W(C03) > by using a colour

Colour temperature

adjustment point

X=0.280 Y=0.282

analyzer so that the colour temperature adjustment

point becomes the value in "HIGH" in the left table.

Don't change < W(C02) > (G drive) values.

(8) If the adjustment method above does not work,

return < W(C01) > and < W(C03) > to 255, and fix

X=0.313 Y=0.329

< W(C01) > at 255.

(9) Adjust WHITE BALANCE by using < W(C02) > and

< W(C03) >.

(10) After the adjustment finishes, escape from the

SERVICE MODE.

(11) Switch COLOUR TEMP of < MAIN MENU > to

"LOW".

(12) Enter the SERVICE MODE again. (13) Select WHITE BALANCE BLOCK. (14) Select "WD : VIDEO LOW". (15) Adjust < W(D01) >(R drive), < W(D02) >(G drive),

and < W(D03) >(B drive) by using a colour analyzer

in the same way as for the COLOUR TEMP HIGH

above.

[WHITE BALANCE BLOCK] (Colour temperature : HIGH) W(E01) : R drive W(E02) : G drive W(E03) : B drive

(1) Input a 480i window pattern (brilliance 70%) signal

from COMPONENT terminal.

(2) Set COLOUR TEMP at "HIGH". (3) Select "WE:COMPO.15k HIGH," and adjust

< W(E01) >(R drive), < W(E02) >(G drive),

and < W(E03) >(B drive) in the same way

as for NTSC.

(4) Set COLOUR TEMP at "LOW". (Colour temperature : LOW) W(F01) : R drive W(F02) : G drive

(5) Select "WF : COMPO.15k LOW," and adjust

< W(F01) >(R drive), < W(F02) >(G drive), and < W(F03) >(B drive) in the same as for NTSC.

W(F03) : B drive

[WHITE BALANCE BLOCK] (Colour temperature : HIGH) W(G01) : R drive W(G02) : G drive W(G03) : B drive

(1) Input a 1080i window pattern (brilliance 70%) signal

from COMPONENT terminal. (2) Set COLOUR TEMP at "HIGH". (3) Select "WG : COMPO. HIGH," and adjust < W(G01)

>(R drive), < W(G02) >(G drive), and < W(G03) >(B

drive) in the same way as for NTSC. (4) Set COLOUR TEMP at "LOW". (5) Select "WH : COMPO. LOW," and adjust < W(H01)

(Colour temperature : LOW)

>(R drive), < W(H02) >(G drive), and < W(H03) >(B

drive) in the same way as for NTSC.

W(H01) : R drive W(H02) : G drive W(H03) : B drive

(No.YA064)1-55

Item

WHITE BALANCE (VGA)

WHITE BALANCE (RGB15k)

BRIGHTNESS (NTSC)

Measuring instrument

Remote control unit

Signal generator

Colour analyzer

Remote control unit

Signal generator

Colour analyzer

Remote control unit

Signal generator

Test point Adjustment part Description

[WHITE BALANCE BLOCK] (Colour temperature : HIGH) W(A01) : R drive W(A02) : G drive W(A03) : B drive

(1) Input a VGA (640 × 480 dots) window pattern

(brilliance 70%) signal from COMPONENT terminal. (2) Set COLOUR TEMP at "HIGH". (3) Select "WA : RGB PC HIGH," and adjust < W(A01)

>(R drive), < W(A02) >(G drive), and < W(A03) >(B

drive) in the same way as for NTSC. (4) Set COLOUR TEMP at "LOW". (5) Select "WB : RGB PC LOW," and adjust < W(B01)

(Colour temperature : LOW)

>(R drive), < W(B02) >(G drive), and < W(B03) >(B

drive) in the same way as for NTSC.

W(B01) : R drive W(B02) : G drive W(B03) : B drive

[WHITE BALANCE BLOCK] (Colour temperature : HIGH) W(A01) : R drive W(A02) : G drive W(A03) : B drive

(1) Input an RGB 15k window pattern (brilliance 70%)

signal from COMPONENT terminal. (2) Set COLOUR TEMP at "HIGH". (3) Select "W I : RGB 15k HIGH," and adjust < W( I 01)

>(R drive), < W( I 02) >(G drive), and < W( I 03) >(B

drive) in the same way as for NTSC. (4) Set COLOUR TEMP at "LOW". (5) Select "WJ : RGB 15k LOW," and adjust < W(J01)

(Colour temperature : LOW)

>(R drive), < W(J02) >(G drive), and < W(J03) >(B

drive) in the same way as for NTSC.

W(B01) : R drive W(B02) : G drive W(B03) : B drive

[WHITE BALANCE BLOCK] W(C07) : Bright

• Confirm that white balance adjustment is finished.

• Set PICTURE ADJ. of MAIN MENU at the initial state. (1) Input an NTSC gray scale pattern (1% step) signal

from VIDEO A terminal. (2) Enter the SERVICE MODE. (3) Select WHITE BALANCE BLOCK. (4) Select "WC : VIDEO HIGH". (5) Select < W(C07) >(Bright). (6) Adjust < W(C07) > so that 6% black slightly shines

on the screen.

123456701 2345670

∗ Be careful so that back component does not shine.

1-56 (No.YA064)

Adjust <W(C07)> so that 6% black

5%

shines slightly on the screen.

Item

BRIGHTNESS (480i)

BRIGHTNESS (1080i)

BRIGHTNESS (VGA)

BRIGHTNESS (RGB15k)

Measuring

instrument

Remote control unit

Signal generator

Remote control unit

Signal generator

Remote control unit

Signal generator

Remote control unit

Signal generator

Test point Adjustment part Description

[WHITE BALANCE BLOCK] W(E7) : Bright

[WHITE BALANCE BLOCK] W(G7) : Bright

[WHITE BALANCE BLOCK] W(A7) : Bright

[WHITE BALANCE BLOCK] W(I 7) : Bright

(1) Input a 480i gray scale pattern (1% step) signal from

COMPONENT terminal.

(2) Select "WC : VIDEO HIGH," and adjust < W(E07)

>(Bright) in the same way as for NTSC.

(1) Input a 1080i gray scale pattern (1% step) signal

from COMONENT terminal.

(2) Select "WG : COMPO HIGH," and adjust < W(G07)

>(Bright) as in the same way for NTSC.

(1) Input a VGA(640 × 480 dots) scale pattern (1% step)

signal from PC terminal.

(2) Select "WA : RGB PS HIGH," and adjust < W(A07)

>(Bright) as in the same way for NTSC.

(1) Input a RGB 15k scale pattern (1% step) signal from

COMPONENT terminal.

(2) Select "WI : RBG15k HIGH," and adjust < W( I 07)

>(Bright) as in the same way for NTSC.

(No.YA064)1-57

SECTION 5

TROUBLESHOOTING

5.1 SELF-DIAGNOSIS FUNCTION

5.1.1 OUTLINE

This model has a "Self-diagnosis function," which checks the operation state of the circuits and temperature inside the set, and informs us of a failure and memorize it when a failure occurs. Diagnosis is performed when the power is turned on, and information input to the main microcomputer is monitored at all time. The diagnosis is displayed on the screen and LED flashing. Failure detection is based on input state of I control lines connected to the main microcomputer.

5.1.2 ENTERING SELF-DIAGNOSIS BLOCK

(1) Enter the SERVICE MODE. (See a page for SERVICE

MODE settings). (2) Select DIAGNOSIS BLOCK in the SERVICE MODE. (3) Self-diagnosis block screen is displayed.

2

C bus and various

SERVICE MENU SCREEN

VCO ADJUST WHITE BALANCE BLOCK CPU BLOCK SIZE/POSITION BLOCK H POSITION BLOCK PANEL BLOCK SIGNAL BLOCK DEVICE INITIAL VALUE

ENTER: SELECT: EXIT:

DIAGNOSIS BLOCK UPDATE CPU PROGRAM HOUR METER BLOCK ENHANCER BLOCK

[1/2]

Fig.1

[2/2]

MENU

5.1.3 ESCAPING FROM SELF-DIAGNOSIS BLOCK

(1) To return to the SERVICE MODE screen, press the [EXIT]

key.

5.1.4 INITIALIZATION OF ITEMS IN DIAGNOSIS

(1) Enter the SERVICE MODE. (Fig. 1) (2) Select DIAGNOSIS BLOCK in the second page (2/2). (Fig.

2)

(3) Adjustment screen for DIAGNOSIS BLOCK is displayed.

(Fig. 3) (4) Confirm that all the items (except TEMP.OVER) are

displayed as "O". (5) If an error occurs in an item, "X" and the number of error

times is displayed in the item. Up to nine times of errors are

counted. If errors occur more than nine times, "9" is

displayed. Unless deleted, the number of error times

remains memorized in a memory. (6) To delete an error, select "CLEAR" and press the [] key.

(Fig. 4) (7) Then, items in DIAGNOSIS is initialized, and all items

(except TEMP.OVER) are displayed as "O". (Fig. 5)

5.1.5 POINTS TO NOTE WHEN USING THE SELF-DIAGNOSIS FEATURE

In addition to circuit failures (abnormal operation), the following cases may also be diagnosed as "Abnormal," and displayed and counted as "X".

(1) Temporary defective transmissions across circuits due to

pulse interruptions

(2) Misalignment in the on/off timing of power for I

2

C bus (Vcc)

when turning on/off the power. Diagonasis may be impeded if I2C SIGNAL BUS, and I2C ROM BUS are displayed as "X". If a failure is expected to reoccur, clear (reset) the failure history to make the unit record the new diagnosis results.

ENTER: SELECT: EXIT:

MENU

Fig.2

SELF-DIAGNOSIS DISPLAY

< DIAGNOSIS BLOCK >

CLEAR I2C SIGNAL BUS : X9 I2C ROM BUS O POWER TEMP. OVER : : O TEMP. OVER [9Eh] TEMP. OVER [9Ch]

ENTER: SELECT: EXIT:

Fig.3

< CLEAR >

!

Are you sure ?

"YES" then Key

"NO" then Key

ENTER: SELECT: EXIT:

< DIAGNOSIS BLOCK >

CLEAR I2C SIGNAL BUS : O I2C ROM BUS : O POWER TEMP. OVER : O TEMP. OVER [9Eh] TEMP. OVER [9Ch]

ENTER: SELECT: EXIT:

MENU

Fig.4

Fig.5

MENU

1-58 (No.YA064)

5.1.6 DETAILS

Type of error Indication Description of detection Detection standard and method Countermeasure

Communication error in video decorder, IP conversion, PDP interface etc

Main memory communication error

2

I2C SIGNAL BUS I

C communication error in MAIN PWB [IC2501]

I2C ROM BUS Communication error for

main memory [IC2502]

When normal communication is not available in spite of up to threetime communication in I

2

C communication, it is judged as an error.

Memorize the number of error times in the main memory (up to nine times).

Memorize the number of error times in the main memory (up to nine times), and turn the power off forcibly.

Temperature rise in power supply part

POWER TEMP. OVER

Alarm signal from SMPS PWB is detected [SMPS PWB]

When ten consecutive errors are detected every 0.5 second, it is judged as an error.

Memorize the error times in the main memory (up to nine times), and turn the power off forcibly.

Temperature rise in DIGITAL PWB

TEMP. OVER [9Eh]

DIGITAL PWB [IC2510]

When the temperature in the DIGITAL PWB is over the setting

63°C centigrade for more than

thirty consecutive seconds

Switch of APC control (Reduce brilliance when the temperature rises.) Display "TEMP/OVER" on the screen.

Temperature rise around power supply part

TEMP. OVER [9Eh]

A sensor in upper part of power supply part detects an error. [IC8101]

In addition, when the temperature in the DIGITAL PWB is over the

setting 120°C for more than thirty

consecutive seconds

When the temperature in and around the power supply part is

over the setting 95°C centigrade

for more than thirty consecutive

Memorize the number of error times in the main memory (up to nine times), and turn the power off forcibly.

Display "TEMP/OVER" on the screen.

seconds

In addition, when the temperature in and around the power supply

part is over the setting 93°C

centigrade for more than one

Memorize the number of error times in the main memory (up to nine times), and turn the

power off forcibly. hundred and twenty consecutive seconds

5.1.7 INDICATION OF SELF DIAGNOSIS BY USING LED

LED for self-diagnosis indication is located on the upper left of the set (on the right of remote sensor).

 SELF-DIAGNOSIS AND FLASHING LED

Diagnosis

Flashing LED

Top Middle Bottom

Priority Indication

Communication error in main memory zz5 Notes :

Abnormal temperature rise in power supply part z z 4

Abnormal temperature rise in DIGITAL PWB z3

Abnormal temperature rise in panel  z 2

Abnormal writing in main memory  1

• Indication color : red

• Flashing interval : 0.25 second

• When two or more errors are detected at the same time, errors are displayed one after another, according to the order of priority.

• All LEDs are lighted while various data are written in the main memory.

z : Lighting /  : Flashing

(No.YA064)1-59

1-60 (No.YA064)

VICTOR COMPANY OF JAPAN, LIMITED

AV & MULTIMEDIA COMPANY VIDEO DISPLAY CATEGORY 12, 3-chome, Moriya-cho, kanagawa-ku, Yokohama, kanagawa-prefecture, 221-8528, Japan

(No.YA064)

Printed in Japan

WPC

GM-V42C

STANDARD CIRCUIT DIAGRAM

NOTE ON USING CIRCUIT DIAGRAMS

1.SAFETY

The components identified by the symbol and shading are critical for safety. For continued safety replace safety ciritical components only with manufactures recommended parts.

2.SPECIFIED VOLTAGE AND WAVEFORM VALUES

The voltage and waveform values have been measured under the following conditions.

(1)Input signal : Colour bar signal (2)Setting positions of

each knob/button and variable resistor

(3)Internal resistance of tester (4)Oscilloscope sweeping time

(5)Voltage values

Since the voltage values of signal circuit vary to some extent according to adjustments, use them as reference values.

: Original setting position when shipped

: DC 20k : H : V

: Othters

: All DC voltage values

/V

20µs / div 5ms / div

Sweeping time is specified

3.INDICATION OF PARTS SYMBOL [EXAMPLE]

In the PW board

: R1209

R209

Type No indication

MM PP MPP MF TF BP

TAN

(3)Coils

No unit Others

(4)Power Supply

Respective voltage values are indicated

(5)Test point

: Test point

(6)Connecting method

: Ceramic capacitor : Metalized mylar capacitor

: Polypropylene capacitor : Metalized polypropylene capacitor : Metalized film capacitor : Thin film capacitor : Bipolar electrolytic capacitor : Tantalum capacitor

: [µH]

: As specified

: B1

: 9V

: Only test point display

: Connector

: Receptacle

: Wrapping or soldering

: B2 (12V

: 5V

)

4.INDICATIONS ON THE CIRCUIT DIAGRAM

(1)Resistors

Resistance value No un i t : [

K M

Rated allowable power No indication : 1/16 [W] Others : As specified

Type No indication OMR MFR MPR UNFR FR

Composition resistor 1/2 [W] is specified as 1/2S or Comp.

(2)Capacitors

Capacitance value

1 or higher : [pF]

less than 1 Withstand voltage

No indication : DC50[V] Others : DC withstand voltage [V] AC indicated

Electrolytic Capacitors

47/50[Example]: Capacitance value [µF]/withstand voltage[V]

]

: [k

]

: [M

]

: Carbon resistor : Oxide metal film resistor : Metal film resistor : Metal plate resistor : Uninflammable resistor : Fusible resistor

: [µF]

: AC withstand voltage [V]

(7)Ground symbol

: LIVE side ground : ISOLATED(NEUTRAL) side ground : EARTH ground : DIGITAL ground

5.NOTE FOR REPAIRING SERVICE

This model's power circuit is partly different in the GND. The difference of the GND is shown by the LIVE : ( ) side GND and the ISOLATED(NEUTRAL) : ( ) side GND. Therefore, care must be taken for the following points.

(1)Do not touch the LIVE side GND or the LIVE side GND and the ISOLATED(NEUTRAL) side GND simultaneously. if the above caution is not respected, an electric shock may be caused. Therefore, make sure that the power cord is surely removed from the receptacle when, for example, the chassis is pulled out.

(2)Do not short between the LIVE side GND and ISOLATED(NEUTRAL side GND or never measure with a measuring apparatus measure with a measuring apparatus ( oscilloscope, etc.) the LIVE side GND and ISOLATED(NEUTRAL) side GND at the same time. If the above precaution is not respected, a fuse or any parts will be broken.

Since the circuit diagram is a standard one, the circuit and circuit constants may be subject to change for improvement without any notice.

NOTE Due improvement in performance, some part numbers show in the circuit diagram may not agree with those indicated in the part list. When ordering parts, please use the numbers that appear in the Parts List.

)

No.YA064 2-1

CONTENTS

SEMICONDUCTOR SHAPES ......................................................................2-2

BLOCK DIAGRAM ........................................................................................ 2-3

CIRCUIT DIAGRAMS .................................................................................... 2-5

PC TERMINAL PWB CIRCUIT DIAGRAM .................................................................................................. 2-5

AV TERMINAL PWB CIRCUIT DIAGRAM .................................................................................................. 2-7

MAIN PWB CIRCUIT DIAGRAM ................................................................................................................ 2-9

DIGITAL PWB CIRCUIT DIAGRAM .......................................................................................................... 2-17

AUDIO PWB CIRCUIT DIAGRAM ............................................................................................................ 2-27

LINE FILTER PWB CIRCUIT DIAGRAM ................................................................................................... 2-29

CONTROL PWB CIRCUIT DIAGRAM ...................................................................................................... 2-30

LED PWB CIRCUIT DIAGRAM ................................................................................................................. 2-30

SP TERMINAL PWB CIRCUIT DIAGRAM ................................................................................................ 2-31

BATTERY PWB CIRCUIT DIAGRAM ........................................................................................................ 2-32

TEMP. SENSOR PWB CIRCUIT DIAGRAM .............................................................................................. 2-32

PATTERN DIAGRAMS .............................................................................. 2-33

MAIN PWB PATTERN .............................................................................................................................. 2-33

DIGITAL PWB PATTERN ......................................................................................................................... 2-37

PC TERMINAL PWB PATTERN ................................................................................................................ 2-41

AV TERMINAL PWB PATTERN ................................................................................................................ 2-41

AUDIO PWB PATTERN ............................................................................................................................ 2-43

SP TERMINAL PWB PATTERN................................................................................................................ 2-43

LED PWB PATTERN ................................................................................................................................ 2-45

BATTERY PWB PATTERN ........................................................................................................................ 2-45

TEMP. SENSOR PWB PATTERN ............................................................................................................. 2-45

CONTROL PWB PATTERN ...................................................................................................................... 2-45

LINE FILTER PWB PATTERN .................................................................................................................. 2-46

SEMICONDUCTOR SHAPES

TRANSISTOR

BOTTOM VIEW FRONT VIEW TOP VIEW

CHIP TR

E C B

ECB

IC

BOTTOM VIEW FRONT VIEW TOP VIEW

OUT E IN

IN OUTE

CHIP IC

N

1

N

B

(G)E(S)C(D)

TOP VIEW

1 N

1

N

ECB

1

1 N

C

BE

N

2-2

No.YA064

MICRO COMPUTER

(CPU)

MB90F584CAPF

VIDEO

DECODER

VP3230D

LPF

3D_YCSEP

UPD64083GF

LPF

ANALOG

SW

TC4053BF

LPF

ANALOG

SW

TC4053BF

3ch AD

CONVERTER & PLL

CXA3506R

ANALOG

SW

BA7657F

BUFFER

TC74LCX16374AT

ANALOG

SW

TC4053BF

SYNC

SEPARATOR-1

(for RGB)

M52346SP

AMP

SYNC

SEPARATOR-2

TA1318N

LPF

EXPANDER0

JLC1562BF

EXPANDER1

JLC1562BF

EXPANDER2

JLC1562BF

TEMP SENSOR

TC75-5.0MOA

AUDIO

SELECTOR

BH3862FS

POWER AMP

TA8200AH

POWER SUPPLY UNIT

LINE

FILTER

EXPANDER3

JLC1562BF

REG

AMDP1 plus

16bit

SDRAM

FLASH

ROM

UV-CONV

FPGA

SCALER

REMBRANDT-1A

PULSE-GEN

FPGA

60MHz

OSC

BUS

BUFFER

2SK1374-X

PDP_IF

FPGA

OSD

M35047FP

ROM

LVDS

Transmitter

DS90CF383A

PDP (PANEL)

EEPROM

64kB

RESET

S-80828CNLB

EXT.SW

LED

INDICATOR

KEY SW

SW

RS232C

DOWN LOAD

WIRED

REMOTE

IR REMOTE

SW

RS232C DRIVER

IR SENSOR

GP1U261X

MM

BUS

BUFFER

2SK1374-X

ANALOG

SW

BUS

BUFFER

2SK1374-X

TIMER

RV5C386A

16M-bit SDRAM

REG

SW_ REG

REG

SW_

REG

SW_ REG

ATT

1/4

*5

BLOCK DIAGRAM

COMPO/RGB(BNC)

Y/G

Pb/B

Pr/R

HD/CS

VD

RGB(D-SUB)

VIDEO A

VIDEO B

S

*75-ON

11

15

6

10

1

5

Y

C

S_DET

R

G

B

VIDEOA

VIDEO B

COMPO/ RGB

OUT

IC1104

ANALOG

SW

TC4053BF

*VIDEO_A *S_DET

Audio-L

Audio-R

Audio-L

Audio-R

Audio-L

Audio-R

Audio-L

Audio-R

HD/CS

VD

HD/CS

VD

G

IC2103

TIMER

SW_ REG

RM1A D3.3V

SW_ REG

IC2104

16bit

SDRAM

IC2512

EXPANDER2

JLC1562BF

IC1403

LPF

3D_YCSEP

UPD64083GF

LPF

R G B

G

IC1203

ANALOG

SW

TC4053BF

IC1206

ANALOG

SW

BA7657F

*D_SUB

GonSYNC

AMP

ATT

1/4

4

AC IN

LPF

HD/CS

VD

Audio-L

Audio-R

Y

G/YIN

Cb

B/PbIN

Cr

R/PrIN

R

R/PrIN2

G

G/YIN2

B

B/PbIN2

G

HD

VD

IC1204

AUDIO

SELECTOR

BH3862FS

IC1105

ANALOG

SW

TC4053BF

*3D_ON

IC1205

CONVERTER & PLL

CXA3506R

CP

IC1303

SYNC

SEPARATOR-1

(for RGB)

M52346SP

3ch AD

CS

VD

LPF

POWER AMP

TA8200AH

FILTER

V1

V2

IC1101

V3(Y)

VIDEO

DECODER

CIN

VP3230D

V4(Component,Sync)

Y

Cb

Cr

VOUT

ANALOG

SW

CP

SYNC1

SYNC2

SEPARATOR-2

TA1318N

HD3

VD3

IC9601

LINE

CbCr

IC1305

DAC1(VS)

SYNC

DAC2(HS)

Y

HD1

SPEAKER

VD1

TC74LCX16374AT

D_CLK1 DIVOUT D_SOG

MMMMLPF

EXPANDER0

JLC1562BF

Audio BUS

14V

15V

IC1106

BUFFER

*SIG_SEL

IC1310

12V

REG

X

D_CLK2

9V

REG

Y/R

Pb/G

Pr/B

I2C1B

CP

HD VD

Y

CbCr

V_CLK1(13.5MHz) V_CLK2(27.0MHz) HS VS AVO INTLC

D_HDREF(=HD/HS) D_CLK_INV(=ADC_SYNC_INV) D_HOLD(=DPLL_COA) CLAMP(=CP)

VS_I

HS_I

HS_50

MM

IC1311

EXPANDER1

JLC1562BF

YC3.3V

A5V

REG

)

(S(SW

STB6V

A5V2

(S(SW

REG

Q1312 Q1313

BUFFER

2SK1374-X

AD3.3V

REG

)

BUS

D5V

1

V_CLK1(13.5MHz) V_CLK2(27.0MHz) HS VS AVO INTLC

VPC

D3.3VSTB5V

3.3V

REG

ANALOG DIGTAL

Y/R Y/R

Pb/CbCr/G Pb/CbCr/G

Pr/B Pr/B

1

D_CLK2 D_CLK2

2 3

CP CP

HD HD

VD VD HS_IN HS_IN VS_IN VS_IN HS_50 HS_50

I2C1 I2C1

Audio BUS Audio BUS

YC D2.5V

REG

POWER SUPPLY UNIT

CLK_OUT3(27.0MHz) HDO(15.75kHz) VDO

1

2 DIVOUT D_SOG D_CLK2

2 3

3 D_CLK_INV(=ADC_SYNC_INV) D_HOLD(=DPLL_COA) CLAMP(=CP)

MICON STB5V

REG

STB6V D5V

CLK_OUT3(27.0MHz) V_HSYNC(31.5kHz) V_VSYNC(=VS) V_ACTIVE(=AVO) V_FIELD(INTLC) D_VSYNC(=VD) D_HSYNC(=HD) D_HSYNC_SYN(=DIVOUT) ADC_SYNC_INV DPLL_COA OPLL_COA DPLL_CLK MPLL_CLK

D_CLK1

D_HDREF(=HD/HS)

IC2507

RV5C386A

AMDP

D5V

D3.3V

IC2120

FLASH

IC2101

AMDP1 plus

CLK_OUT3(27.0MHz) V_HSYNC(31.5kHz) VDO SIG1 SIG2

IC2513

EXPANDER3

JLC1562BF

FPGA

RM1A

D2.5V

D1.8V

SW_

REG

ROM

Y

Pb

Pr

LVDS

3.3V

REG

IC2251

UV-CONV

FPGA

IC2201

PULSE-GEN

FPGA

IC2510

TEMP SENSOR

TC75-5.0MOA

HD VDCP

Y

Pb/Pr

I2C1

REMBRANDT-1A

R G

B

HS_50

IC2504

S-80828CNLB

IC2303

SCALER

60MHz

OSC

IC2502

EEPROM

64kB

RESET

16M-bit SDRAM

*5

IC2306

IC2310

RM_HSYNC RM_VSYNC RM_CLK

I2C1A

BUS

BUFFER

2SK1374-X

HS_IN

VS_IN

I2C1

I2C

I2C0

RESET

AUDIO_BUS

POWER CONTROL

R

G

B

SCALER BUS

IC2406

ROM

IC2403

PDP_IF

FPGA

RGB

OSD

M35047FP

IC2501

MICRO COMPUTER

(CPU)

MB90F584CAPF

R

G

B

LV_HSYNO LV_VSYNC

I2C2

IC2407

LVDS

Transmitter

DS90CF383A

SW

Rx 0 3

CLK

BUS

BUFFER

2SK1374-X

SERIAL I/F CONNECTOR

DOWN LOAD

RS232C

EXT.SW

LED

INDICATOR

KEY SW

WIRED

REMOTE

IR REMOTE

I2C2A

CN2201

Rx 0

Rx 3

RD RD

31Pin

RS232C DRIVER

IR SENSOR

GP1U261X

PDP (PANEL)

No.YA064 No.YA064

2-42-3

CIRCUIT DIAGRAMS

PC TERMINAL PWB CIRCUIT DIAGRAM SHEET1

J5501 QNZ0061-001

R5501 R5502 150 150

J5503 QNZ0060-001

REMOTE

WIRED

J5502 QMS3005-C01

J5504

QMS3005-C01

R5503 150

R5505 R5506 150 150

R5507 470

R5508 470

R5521 R5522 R5523 150 150 150

C5511

.01

R5504 150

L5501

*5

L5502

*5

R5524

150

EF5501

*4

C5501

0.0047

C5502

0.0047

R5525 R5526

150 150

R5532

10k

R5531 10k

R5511 220k

R5512 220k

R5513

1k

R5514

1k

R5527

150

R5533 100k

R5528

150

D5501

*1

NOTE

*1

*2

*3

*4

*5

OPEN

MA3056/M/-X

:

MA3120WA-X

:

2SC3773/3-4/-X

:

NQR0321-001X

:

NQL092K-5R6X

:

NON MOUNT

CN5003 QGB1230J1-15

CN5004 QGB1230J1-09

MAIN PWB (SHEET 4)

MAIN PWB (SHEET 5)

REMOTE

MAKE

J5506 QMCC006-C01

J5507 QNN0321-001

C5541

R5541 OPEN

C5521

0.0047

R5547

10

No.YA064 No.YA064

R5542 10k

C5522

0.0047 GND

C5531

0.0047

D5513

*1

R5543

100

R5544

100

D5511 D5512 *1 *1

L5510

L5511

C5532

0.0047

2-5 2-6

*5

0.01

R5553

560

R5554

560

PC TERMINAL PWB ASS'Y

LCA90118-01A(FV-5001A)

CN5005 QGB1230J1-15

VIDEO A

VIDEO B

VIDEO IN

VIDEO OUT

AUDIO

L/MONO

VIDEO IN

R

Y/C

J5001 QNZ0417-001

J5002 QNN0321-001

J5004 QMCC006-C01

J5003 QNN0202-003

L5101

*5

L5102

*5

R5201 R5202

150 150

R5203 R5204

150 150

R5205 R5206

150 150

C5101

0.0047

C5102

0.0047

EF5101

R5102R5101

OPENOPEN

R5103 220k

R5104 220k

R5105

EF5201

AV TERMINAL PWB ASS'Y

LCA90119-01B(FV-5002A)

*4

1k

R5106

1k

*4

EF5202

R5207

10

EF5203

*4

D5201 *1

*4

R5315

QGB1230J1-15

0

CN5001

MAIN PWB (SHEET 3)

AUDIO

L/MONO

R

J5006 CEMB010-004

AUDIO

L/MONO

J5005 QNN0321-001

J5007 QNZ0417-001

J5008 QNN0321-001

R

R5301 OPEN

R5303

OPEN

R5305

OPEN

L5201

*5

L5202

*5

R5302 OPEN

R5304 OPEN

R5306 OPEN

L5301

L5302

R5211 220k

R5311 220k

R5212 220k

EF5305

*4

R5312 220k

R5213

1k

R5214

1k

R5313

1k

R5314

1k

NOTE

*1

*2

*3

*4

*5

OPEN

MA3056/M/-X

:

MA111-X

:

2SC3773/3-4/-X

:

NQR0321-001X

:

NQL092K-5R6X

:

NON MOUNT

:

CN5002 QGB1230J1-15

MAIN PWB (SHEET 3)

C5201

0.0047

C5202

0.0047

EF5304

*4

R5307 1k

R5308 1k

*5

C5301

*5

0.0047

C5302

0.0047

No.YA064 No.YA064

2-82-7

MAIN PWB CIRCUIT DIAGRAM (1/4) SHEET 3

AV

TERMINAL

PWB

(SHEET 2)

SHEET 4,5,6

AV

TERMINAL

PWB

(SHEET 2)

CN1001

SHEET 4

SHEET 5

SHEET 4

SHEET 5

CN1002

IC1104 2 4

1.5 0.7

R1A16

R1A17

150

AL1

AR1

AL2

AR2

VOUT

Y1[G]A

D5V

12V

A5V

AL3

AR3

D_DET

LINE3

LINE2

LINE1

D5V

PCMODE

S_DET

STB6V

C1133 100

R1A18

R1A20

R1A26

0

5.1V

OPEN

C1101 10

R1102

56k

C1102 10

C1103 10

R1A19

OPEN

C1104 10

R1A21

OPEN

R1191

R1176 10k

C1168

4.7

IC1105 1 2

R1101 27k

D1101 *9

R1105

27k

R1106 56k

R1109 27k

R1110 56k

R1113 27k

R1114 56k

C1107 10

R1A01 75

C1108 10

R1A02 75

C1109 R1125 10 27k

R1A03 75

C1110 10 27k

C1111 R1133 10 27k

IC1103

3.6V

4.9V

1.1V

47k

R1177

1.5k

R1178

1.5k

R1179 1k

R1117 27k

R1118 27k

R1121 27k

R1122 27k

R1126 27k

R1129

R1130 27k

R1134 27k

7.9V

R1103

100

D1103

*6

7.9V

R1107 100

D1104

*6

D1105 *6

7.9V

R1111 100

D1106

*6

D1107

*6

7.9V

R1115

100

D1108

*6

D1109

*6

R1119

220

D1110

*6

D1111 *6

R1123

220

D1112

*6

D1113 *6

R1127

D1114

*6

D1115

*6

R1131

220

D1116 *6

D1117

*6

R1135

220

D1118

*6

0V

220

11.9V

R1104

5.6k

11.9V

R1108

5.6k

11.9V

R1112

5.6k

R1116

5.6k

C1112

27p

C1113

22p

C1114

22p

C1115

22p

C1116

22p

11.9V

Q1101

*1

7.3V

Q1102

*1

7.3V

Q1103

*1

7.3V

Q1104

*1

7.3V

11.9V

5.7V

11.9V

5.7V

11.9V

5.7V

11.9V

5.7V

11.9V

5.7V

IC1105 12 14

1

12V

C1106

0.01

C1105 47

5.2V

Q1105

*1

5V

R1120

1.2k

C1118

0.01

C1117 47

Q1106

*1

5V

R1124

1.2k C1171

47p

Q1107

*1

PR[R]

5V

R1128

1.2k

R1132

2.2k

A5V

Q1108

*1

5V

Q1109 *1

5V

R1136

2.2k

C1172 47p

HD3

VD3

Q1110

*1

R1140

2.7k1022k

11.9V

Y1[G]

PB[B]

220

R1A27

5.8V

R1139

RY1101

220

R1A28

R1138

22k

330

R1A29

220

R1A30

R1137

220

R1A31

100

C1120

OPEN

INPUT3

*6

330

R1A32

C1119

IC1104 IC1105

C1163

11.9V

47

7.3V

C1164

0.1

11.9V 0V

R1180 R1181 10k 10k

0V

*7 *7

*7

Q1113

R1198

15k

R1195

1.5k

8.9V

Q1118 *1

3.2V

R1196

1.5k

C1146 10

A5V

C1148 47

C1155

0.22

C1156

0.0015

C1158

100

R1141

OPEN

R1142

C1175 C1174 C1173 330p

*5

D1120

7.3V

YC_SEL

4.2V

Q1112

R1193

5.6k

R1192

2.2k C1169

8V

Q1117 *2

R1194

2.2k

R1143

3.8V

TPAGND

18p

L1105 15

OPEN

7.3V

11.9V

Q1119 *1

8.2V

R1197

3.9k

C1160 330p

330p

0V

C1149

0.0015

C1150

C1151

C1152

C1153

C1154R1159

OPEN

R1189

0

C1147

0.047

1000p

0.22

0.1

0.22

0.220

C1159

0.047

C1157 390p

11.9V

R1182 22k

C1166 10

C1165

7.3V

8.2V

X1101

2.4V

0V

4.8V

1.4V

1.6V

1.3V

1.1V

2.4V

4.8V

0V

2.1V

0V

C1176

C1177

C1178

330p

11.9V

0.1

8.2V

1.5V

8.3V

1.4V

0V

TP-V2 TP-H2

3.3

C1145

3p

1.3V 0.5V 1.4V 1.1V1.3V 1.4V 0V 3.2V 3.2V 0V 0V 4.9V 3.2V 0V 0V 0V4.9V

0.22

2.2V

R1144 75

R1145 75

R1146 75

2.2V

C1122

C1144 3p

C1121

C1124 330p

C1143

C1123

0.22

330p

0V

0.1

R1188 10k

TP-V2

TP-H2

6.9V

R1183 33k

R1184

3.3k

11.9V

R1185 22k

C1167

0.01

6.9V

R1186 33k

R1187

3.3k

4.2V

Q1114

*5

VS

HS

10

R1157

0V

C1125

0.22

C1126 330p

0.1V 2.7V 2.4V 1.5V 3.1V

K1101

4.8V

0.22

Q1115 *1

6.3V

Q1116

*1

6.3V

3.3

OPEN

TP1102

TP1101

OPEN

C1141

0.047

C1142

OPEN

0.0015

R1190

IC1101

VIDEO DECODER

C1127

0.22

C1129

0.0015

100

R1147

R1148

SCL1B

C1128 390p

VC0

101010

R1175

0V

100

SDA1B

I2C1B

VC2

VC1

10

R1174

R1173

R1172

1V 1V 1V 1V

C1130 OPEN

R1150

0

IC1101 71

IC1101 72

IC1101 74

C1140

0.068

VC3

R1153

7.2V

C1131 OPEN

0.7

1.5

0

3.2V

C1132

0.1

1

3.2V

IC1102

VC4

VC5

101010

R1171

R1170

0.1V

0.6V

D1119 *6

R1151 47k

R1152

4.7k

R1169

YCVYIN

YCCIN

YCYOUT

YCCOUT

SHEET 6

SHEET 4

3D_ON

VIDEO_A

D_HDREF

V_CLK1 V_CLK2

D5V

3.2V

5.1V

R1A22

C1138

0.068

C1137

0.068

L1104

6.8

10

C1136

0.047

VY0

VY1

VY2

VY3

VY4

VY5

VY6

VY7

V_CLK1

V_CLK2

820

R1A23 820

R1A05

R1A07

C1183

C1184

0.01

47

VC6

VC7

10

R1168

2V

1V

VPC3.3V

C1139 47

R1167

1.6V

R1166

1.6V

R1165

1.6V

R1164

1.5V

3.2V

R1163

1.6V

R1162

0.1V

R1161

0V

R1160

0V

0.5V

R1155

0.1V

R1154

0.1V

3.1V

C1135

0V

0.0015

MAIN PWB ASS'Y(1/4)

IC1107

1.2V

C1185 C1186

100 0.01

R1A24

1k

R1A04

0 VY7 VY6 VY5 VY4

0 VY3 VY2 VY1 VY0

R1A06

VC7 VC6 VC5 VC4

0

VC3 VC2 VC1 VC0

R1A12

1.6V

0.9V

1.4V

C1179

3.2V

0.1

1.8V 1V

1.5V

1.8V

0

2.1V 1V

1V 1V

C1180

3.2V

0.1

1V 1V

1.6V

0

IC1106

VPC3.3V

0V

3.2V

1V 1V

0V

R1A08

VY7A

0.9V

VY6A

0.9V

VY5A

1.4V

VY4A

1.4V

R1A09

0.1

C1181

VY3A

1.8V

VY2A

1V

VY1A

1.5V

VY0A

1.8V

R1A10

VC7A

2.1V

VC6A

1V

VC5A

1V

VC4A

1V

R1A11

0.1

C1182

VC3A VC2A

VC1A VC0A

D5V

D5V R1A14 OPEN

R1A13

R1A15 OPEN

HS VS

D_HOLD

D_CLKINV

D_HDREF

D_CLK1 D_CLK2

DIVOUT

Y[R]0 Y[R]1 Y[R]2 Y[R]3 Y[R]4 Y[R]5 Y[R]6 Y[R]7

PB[G]0 PB[G]1 PB[G]2 PB[G]3 PB[G]4 PB[G]5 PB[G]6 PB[G]7

Y[R]/VY

PR[B]0 PR[B]1 PR[B]2

PB[G]/VC

PR[B]3 PR[B]4 PR[B]5

PR[B]

PR[B]6 PR[B]7

0

Y[R]7 Y[R]6 Y[R]5 Y[R]4

0

Y[R]3 Y[R]2 Y[R]1 Y[R]0

0

PB[G]7 PB[G]6 PB[G]5 PB[G]4

0

PB[G]3 PB[G]2 PB[G]1 PB[G]0

AD_SEL

0

CN100K

AD_SEL

SHEET 5

SHEET 4

DIGITAL PWB (SHEET 7)

SHEET 4

SHEET 5

LCA90114-02C(FV-1004A)

A5V_SW

TERM_SW

R1158 10k

3V

Q1111

*1

4.8V

0V

C1161 C1162

100 0.1

No.YA064 No.YA064

R1A33

C1187 10/16

11.9V

D1121

*6

Q1120

*1

3V

10K

R1A34

470K

0V

2-9 2-10

MAIN PWB CIRCUIT DIAGRAM (2/4) SHEET 4

4.9V

R1203 27k

R1204 27k

R1207 27k

R1208 27k

R1211 27k

R1212 27k

R1215 27k

R1216 33k

R1219 27k

R1220 33k

1.1V

R1272

R1273

R1274

1k

IC1201

1.5k

D1201 *6

5.8V

R1205 220

D1202

*6

C1209 33p

D1203

*6

5.8V

R1209 220

D1204

*6

C1211 33p

D1205

*6

5.8V

R1213 220

D1206 *6

C1213 33p

D1207

*6

5.8V

R1217 220

D1208

*6

C1217 47p

D1209 *6

5.8V

R1221 220

D1210 *6

C1219 56p

R1229

47k

C1226

R1230

C1227

15k

R1231

C1228

15k

R1232

C1229

15k

R1233

15k

47

C1231

R1234

C1232

15k

R1235

C1233

15k

R1236

C1234

15k

R1237

15k

R1238

C1235

47k

47

SHEET 5

PC

TERMINAL

PWB

(SHEET 1)

SHEET 5

SHEET 3

SHEET 5

SHEET 3

CN1003

SHEET 3

STB6V

12V

A5V_SW

INPUT3

DSUB

GONSYNC

CSYNC

VSYNC

A5V

AL1

AR1

AL2

AR2

AL3

AR3

L_OUT

R_OUT

D5V

EF1201

EF1202

EF1203

EF1204

EF1205

STB6V

5.1V

R1288

3.6V

47k

C1201 100

R1201 10k

R1202 10k

*4

0V

Q1201

C1294 47

*1

4.5V

C1208

R1267

10

OPEN R1268

OPEN R1269

OPEN R1270

OPEN R1271

OPEN

C1210 10

C1212 10

C1216 10

C1218 10

11.9V

C1222

4.7

5.9V

R1283

5.3V

Q1207

100

*1

R1223

4.7k

11.9V

C1223

4.7

5.9V

R1282

5.3V

Q1208

100

*1

R1226

4.7k

R1289

47k

R1290

47k

R1291

47k

R1292

47k

R1293

47k

R1294

47k

R1295

47k

R1296

47k

C1202 C1203

100 0.1

12V

11.9V

Q1202

*1

5.2V

R1206

3.3k

11.9V

Q1203

*1

5.2V

R1210

3.3k

11.9V

Q1204

*1

5.2V

R1214

3.3k

11.9V

Q1205

*1

5.2V

R1218

2.2k

11.9V

Q1206

*1

5.2V

R1222

2.2k

C1224 10

C1225 10

10

C1230

10

D1211

D1212

D1213

D1214

D1215

D1216

D1217

D1218

C1B15

0V

R1280

2V

R1279

10k

1k

Y1[G]

C1B19

C1293

0.1

IC1205 1 21

0.8

C1B16 .01

4.9V

47

C1B21

11.9V

0.1

8.1V

Q1219

*1

7.5V

R1B26

2.2k

C1B20

C1295

0.1

R1252

0

RY1201

0

R1B04

R1B03

AR

AG

AB

D1219

*6

0

220k

R1B14

220k

R1B13

A5V2

C1204 C1205

100 0.01

VD3

Y1[G]

Q1216

R1B27

100

R1B28

1.2k

R

G

C1215C1214

470.01 B

IC1209

11.9V

IC1204

2.4V

*3

2.4V

*3

2.4V

*3

2.4V

*3

2.4V

*3

2.4V

*3

2.4V

*3

2.4V

*3

HD3

*1

R1B29 0

5.1V

5.7V

5.2V

5.7V

R1281

10k

A5V

5V0V

2.4V

2.3V

2.4V

5V

0V

C1244

100

0V

PR[R]

Y1[G]

PB[B]

R

INPUT4

IC1203

11.9V

5.6V

0V 5.2V

Q1211

*7

C1289 10

C1290 10

C1236

0.0047 C1237

0.0047 R1239

C1238

0.22

C1239

2.2k

0.22

C1242

0.22

C1243

0.22

R1240

2.2k

C1245

0.1 R1241

100

LA

R1242 100

CL

R1243 100

DA

AUDIO

I2C1B

G

5.2V

4.4V

R1227

R1228

C1240

4.7

C1241

4.7

B

C1220

0.1 47

22k

C1B01 47

C1B03 47

C1B05 47

C1B07 47

C1B09 47

C1B11 47

C1221

R1224

22k

R1225

22k

4.5V

R1275

820

R1276 820

C1B02

.01

C1B04 .01

C1B06 .01

C1B08 .01

C1B10 .01

C1B12 .01

G

C1B17 47

R1285 33k

C1291

OPEN R1284

10k

C1296

0.33

IC1202

3.2V

1.1V

R1277

1k

C1B13 150p

R1278

3.5V

470k

0V

C1B14

3.5V

330p

3.5V

0V

11.9V

4V

Q1217 *1

3.4V

R1B18

C1B18

15k

8p 1.8k

R1B21

1.5k

R1B19 R1B23

1.2k 1.5k

IC1207

5.9V

5.9V 0V

R1244 27k

2.6V

R1246 220

R1245 33k

R1249 27k

2.6V

R1251 220

R1250 33k

100

Q1218

R1B20

C1297

0.33

C1206

*1

5.9V

4.9V

IC1206

R1B22 R1B24

1.5k 8.2k

8.1V

3.5V

11.9V

5.9V

C1292

OPEN

R1286 10k

Q1209

*1

2V

R1248

2.2k

Q1210

*1

2V

R1253

2.2k

C1207

0.01

2V

4V

3.6V

3.8V

R1B25

4.7k100.01

R1287 33k

IC1205 3 19

0.8 0.8

C1248

0.1

C1251 100p

R1254

3.3k C1252 330p

C1253

0.33

C1254 100p

AR

C1258

0.1

PB[B]

AG

C1268

0.1

0.6V

R1297

R1B07

1k

0

R1B08R1B05 220k220k

C1269

0.1

R1298

680

R1B06

R1B16 R1B15

220k 220k

PR[R]

AB

Q1212

0V

*1

C1250

C1259

C1272

0

C1249

0.1

C1260

0.1 C1261

C1263

0.1

C1264

C1266

0.1

C1273

0.1

IC1205 5 15

R1262 OPEN

R1266

0

C1288

C1287

0.1

C1B23

OPEN

R1B34

4.6V

0.1V 5V

4.9V

1.7V

2.5V

R1255

4.9V

3k

1V

C1255

0.1

C1256

2.9V

0.1

4.8V

C1257

2.3V

0.1

2.9V

0.1

2.9V

C1262

2.9V

0.1

2.9V

C1265

2.9V

0.1

4.3V

0.1

2.9V

C1267

2.3V

0.1

C1270

3.4V

0.1

4.9V

C1271

2.3V

0.1

4.9V

C1275

0.1

C1274

0.1

R1256 OPEN

C1276

0.1

R1B02

3.3k

Q1214

2V

*1

0V

R1B09

0

2.6V

Q1215

*1

0V

R1B11 OPEN

0V

R1B10

3.3k

D_HOLD

D_CLKINV

0V

5.2V0V0V

4.9V0V4.9V

R1257

0

R1299

2.2k

Q1213

*1

R1B30

0.6V

47K

CLAMP

0.1V

0V

D_CLK2

D_CLK1

DIVOUT

10

R1263

10

R1265

R1264

1.4V

1.4V0V1.4V5V1.5V

5V

4.9V

C1277

0.1

C1278

R1260 R1261

100 100

SDA1B

SCL1B

IC1208

TP-H3 *5

10

3ch AD CONVERTER

4.9V0V4.9V

R1258 OPEN

R1259

00.1

D1220

R1B01

15

R1B12 OPEN

R1B17 OPEN

0.1

C1286

1

1.7V

3.2V

C1279

1.5V5V5V

2.8V

1

4.9V

C1B22

IC1205

PLL

3.2V

R1B31

OPEN

R1B32

R1B33

&

5V

0

OPEN

Y[R]/VY

Y[R]5

Y[R]6

C1284C1285

0.10.1

Y[R]7

0.9V

5V

0.9V

1.7V

C1283

0.1

C1282

0.1

Y[R]4 Y[R]3 Y[R]2 Y[R]1 Y[R]0

PB[G]7 PB[G]6 PB[G]5

PB[G]4 PB[G]3 PB[G]2 PB[G]1 PB[G]0

1.6V

5V

0.9V

0.3V

5V

C1281

0.1

0V

0V0V0V

PR[B]0

0V

PR[B]1

PR[B]2

K1201

0V

PR[B]3

PR[B]4

PR[B]5

PR[B]6

0V

PR[B]7

5V

GND1

C1280

0.1

GND

MAIN PWB ASS'Y(2/4)

LCA90114-02C(FV-1004A)

D_HDREF

CLAMP

Y[R]/VY

PB[G]/VC

PR[B]

14V_SW

LED_1B

AC_DET A_MUTE2 A_MUTE

15V

CN100A

SHEET 5

SHEET 3

SHEET 5

AUDI O

PWB

(SHEET 12)

No.YA064 No.YA064

2-122-11

MAIN PWB CIRCUIT DIAGRAM (3/4) SHEET 5

PC

TERMINAL

PWB

(SHEET 1)

VIDEO

SMPS

PWB

TO

PDP

UNIT

SHEET 3,4,6

CN1004

PC

TERMINAL

PWB

(SHEET 1)

SHEET 4

SHEET 6

SHEET 3,4

SHEET 4

SHEET 3,4

SHEET 3

SHEET 4

YC12V

STB6V

CN100E

L1302

D5V

15V

C1301 22

C1302 22

C1303

12V

A5V

Y1[G]A

VOUT

GONSYNC

R1301

27k

C1313

10

CSYNC

R1302

27k

VSYNC

D1307 D1308 D1309 D1310

*9 *9 *9 *9

D1311

*9

CN1005

R1374

100

R1375

100

R_OUT

L_OUT

15V

0.1

11.9V 11.9V

Q1301

*1

5.6V

0.5V

R1303

1k

D1312

*9

CLAMP

C1304 C1305 47

R1379

OPEN

D1304

*6

C1314 10

R1304

220k

D1313

L1303

IC1301

11.9V

0.1

D1306

*6

D1305

*6

11.2V

9.7V

R1305

5.6k

*9

Q1302

*2

C1306 47

R1389

D1314

YC12V

IC1318

R1310 100k

0.01

IC1312

5.2V

C1360

100

R1309 100

3.9V 4V

6.1V

0.1

6.1V

4.1V

R1311

22k

9.3V

0V

4.9V

-9.8V

0V

4.9V

0V

-9.8V

-4.9V

5.1V

C1353 1

C1357

0.1

R1376

10k

RIN_DET

4.9V

IC1303

C1352 1

MAKE_SW

STB5V

C1362

0.1

C1361

100

C1325 L1301

C1324 100p

0.01

2.2

3.3V

R1312

18k

0V

11.9V 0V 0V

0V

0.1V

RGB

IR_REM

REM_IN

232C

DTR

RI

CTS DSR RTS

5V

Q1309

R1390

33

3V

0V

R1392

4.7k

C1326 47

C1327 C1328

10p 100p

R1320

22k

R1391

OPEN

*1

R1319

0.5V

Q1310

0

IC1313

0V

R1313

2.2k

R1314

2.2k

R1315

2.2k

R1316

2.2k

R1317

R1318

33k

A5V

R1384

Q1307

OPEN

R1385

0

R1387

0

*1

R1393

5.6k

R1386

OPEN

C1330

0.01

C1368

C1358

0.1

CLP_RGB

Q1311

4.5V

OPEN

R1394 OPEN

-0.1V

C1329 100

GND

A5V

4.9V

0.1V

0V

4.2V

47k

0V

Q1304

GND

4.5V

11.9V

15V

C1359

100

12V

R1308

2.2k

C1316 C1317

D1301

*6

C1315 120p

0V

0.5V

R1306

10k

R1307

22k

5.6k

R1366

100

*9

R1367 R1368 R1369

R1370 R1371 R1372

R1373

100

C1356

.01

SW2

SW_DET

1

Q1303

*1 D1302 D1303

*6

100 100 100

C1350 1

C1354

C1355

47

0.01

SW1

-0.1V

1

*6

TD_OUT

RD_IN

DCD

C1351 1

4.9V

IC1309

4.7

C1321

4.9V

7.3V

9.8V

2.3V

10

9.8V

-9.8V

0V

4.9V

0V

IC1307

4.9V

C1363

4.9V

3.4V

C1318 1

C1320

0V

4.9V

C1319

0.0047

C1322 10

C1323

C1308

47

R1388 OPEN

C1309

R1321

0.1

1K

R1323

1.5k

IC1302

9V

15V

0V

C1310 C1311 47 0.1

R1322

1.8k

4.6V

IC1304

150P

9V

C1332

0.1

9V

Q1305

3.9V

R1324 1k

9V

C1312C1307 4747

C1333 47

C1367 470

C1335

0.1

C1334 470

C1337

0.01

R1325

X1301

R1327

R1326C1336

10k0.47

1k

R1328

560

R1398

82K

C1338

0.01

*1

A5V

4.9V

TP-V1

5

CLP_HD

TP-H1

IC1310

VIDEO

4.9V

R1350 100

4.9V

5V

R1351

100

0V

4.7V

4.9V 5V

R1355

R1347

4.7k

R1348

4.7k

CTL_SW1

C1348

R1346

4.7k

R1349

4.5

4.9V

0.1

4.7V 0V

4.2V

4.9V

4.7k

MAIN PWB ASS'Y(3/4)

LCA90114-02C(FV-1004A)

IC1305

C1339

R1331

0.1

0.5V

1.7V

0.1V

R1352

4.7k

SW1 SW2

SW_DET

0

6.8V

0V

R1329

5V

9V

2.2k

SDA1

SCL1

R1354

4.7k

R1330

4.7k

R1353

4.7k

R1356

R1359

C1349

4.7k

100k

3.5V

0.3V

4.8V

2.3V

6.5V 2V

C1341

1

0.3V

0.5V

IC1314

0.5V

4.8V

R1C07

I2C1

SDA1

SCL1

0.1

R1357

4.7k

4.7V

3.7V

4.9V

R1358

100k

IC1311

4.7k R1332

4.7k R1333

4.7k

C1340 1

R1336

4.7V

47k

100

4.7V

R1337

100

R1338

4.7k

R1339

2.7k

*5

TP-V1

TP-H1

*5

C1370

0.1

R1C08

OPEN

4.9V

4.7V 0V

R1C09

O

0.1V

R1C10

O

R1C11

OPEN

2.1V

4.4V

STB5V

R1360

100

4.9V

4.7V

R1361

100

0V

3.9V

4.2V

4.9V

R1334

2.2k

IC1315

R1362

4.7k

VD

R1335

4.7k

SCL1

R1C12

TP-VI

5

TP-VI

*5

C1342 100

C1344

0.01

R1341 82k

R1343

R1342

4.7k

2.2k

C1345C1331

0.0068

0.0056

IC1316

C1372

0.1

4.9V

4.5V

0.3V

C1343

270p

R1340

SDA1

IC1306

0V

2.9V

4.9V

82k

0.3V

R1399

2.6V

27k

2.1V

2.6V

C1369 1000p

Q1308

*7

TP-HI

C1347

4.9V

0V

4.6V

4.4V

4.6V

0.1

*5

R1C17

47k

TP-HI

4.5

HD

HS_50

4.9V

C1371

R1C13

0.1

OPEN

2.6V 0V

0V

R1C15

0

R1C16

47k

4.7k

100k

R1363

R1364

R1365

OPEN

VS_50

R1C14

0

SCL1

Q1312

R1C01

5.2V

10k

4.9V 4.9V

4.7V 4.7V

R1C05 R1C06

OPEN OPEN

R1C04

100

SCL1B

R1C02

10k

SDA1B

D5V

SDA1

5.2V

Q1313

R1C03 100

R1C18

OPEN

R1C19

OPEN

R1C20

I2C1B

R1345

4.7k

R1C21

Q1306 *1

R1344C1346 18k

0

4.6V

47K

DCD DSR TD_OUT RTS RD_IN CTS DTR RI REM_IN

IR_REM

PCMODE

D_DET

AUDIO

A5V_SW

A_MUTE

A_MUTE2

0V

DA LA CL SDA1 SCL1

0V

LED_1B

4.6V

AC_DET

HD

VD

HS_50

VS_50

IC1317

CN100J

SHEET 3,4

4.9V

0.2V

SHEET 4

SHEET 3

SHEET 4

R1C22

OPEN

C1373

0.1

R1C24

0

DIGITAL

PWB

(SHEET 11)

R1C23 OPEN

SHEET 3,4,6

AD_SEL DSUB LINE3

S_DET

LINE1 LINE2

3D_ON VIDEO_A YC_SEL

TERM_SW

14V_SW

SHEET 3

SHEET 4

SHEET 3

SHEET 4

No.YA064 No.YA064

2-13 2-14

MAIN PWB CIRCUIT DIAGRAM (4/4) SHEET 6

SHEET 5

SHEET 3

SHEET 5

D5V

A5V

YC12V

EF1406

EF1407 C1401

L1404

VC12YC

IC1405

5.2V

C1414

R1D10

2.4V

VC2.5_1

VC2.5_2

5.2V

1K

C1415

0.1

C1416 100

C1417

0.1

VC2.5_1

R1495

VC2.5_2

C1474

1

0.1

MAIN PWB ASS'Y(4/4)

LCA90114-02C(FV-1004A)

C1476

0.01

L1403

C1402

0.1

47

VCVINYC

SHEET 3

YCVYIN

YCCIN

EF1405

EF1408

EF1409

4.7

C1408

C1478 47

IC1406

R1401

C1473 33

R1403

R1412

C1409

R1414

R1439 0

C1445

0.1

2.3V

1.2V

R1431

0

C1439

L1417

C1419

0.1

VC2.5_3

L1416

VC2.5_3

C1475

0.1

GND

C1446

0.1

R1459

R1474

R1475

100

R1458

100

0

VCYOUTYC

C1461

0.1

C1467

0.1

1.2V

1.3V

Q1411

*10

VCCOUTYC

Q1415

*10

VCYOUTYC

R1460

4.7K

1.8V

R1461

180

C1463

100p

VCCOUTYC

R1476

4.7K

R1477

120

6.9V

C1469 220p

C1462

R1462

L1411

C1468

OPEN

R1478

OPEN

L1412

R1466

1k

68

11.2V

*1

1.2V

R1470

2.2k

6.8k C1465

33p

11.8V

R1467

1.4V

Q1413 *10

220

R1473

C1466

4.7

EF1404

68

YCYOUT

R1464

R1463

OPEN

100

R1465

Q1412

1.8V

R1468 R1469

15p

10k

C1464 120p

SHEET 3

C1472

4.7

C1470 220p

R1479

R1480

OPEN

R1488

R1487

100

1.5k

8.9V

7.7V

Q1418

*10

R1481

2.2k

R1482

2.7k

2.5V

Q1417 *10

1.9V

100

R1489

EF1403

68

YCCOUT

0

0V

R1440

4.3V

0

I2C1B

SHEET 5

EF1402 OPEN

L1402

SDA1B

SCL1B

L1413

2V

0V

R1446 10k

4.9V

10k

R1447

3V

5.2V

OPEN

R1448

2.6V

R1449

10k

0V

2.3V

1.1V

C1451 OPEN

C1453 22p

33

C1454 56p

GND2

1.2V

R1455 OPEN

R1496 1k

2.3V

Q1410

0.6V

R1456 270

*1

C1455

0.01

C1450

0.1

GND2

C1456

0.1

R1457 470

L1410

C1457 560p

C1477

100/6.3

R1494 470

OPEN

C1458 OPEN

R1452

C1452 OPEN

L1414

IC1404

68

5.2V

R1453

0

C1460

0.1

C1459

0.01

R1490 220

R1491 220

EF1401 OPEN

R1492 OPEN

R1493

L1401

0

C1418

R1430

4.7k

4.3V

C1436 47

6V0V0V

X1401

C1447 10p

Q1409 *1

C1437

0.1

2.4V

R1441

100

C1423 10

C1438

0.1

C1444

0.1

1.2V

1.1V

0.5V

0.9V

1V

2.3V

1.1V

330

C1448 10p

2-162-15

5.9V

R1408

R1409

68

1k

11.8V8.4V

5.9V

0

VCVINYC

R1411

0

R1410

1.5k

6.1V

Q1403

*10

5.5V

VCCINYC

R1422 0

R1421

1.5k

Q1405 *1

6.6V

Q1406

5.9V

*10

R1420 1k

IC1101 83

1

IC1101 88

1.2

R1D01 OPEN

R1D02 OPEN

R1D03 OPEN

R1D04 OPEN

R1D05 OPEN

R1D06 OPEN

R1D07 OPEN

C1425

C1420

0.1

C1424

2.2

C1422 1000p

R1423 220

R1433

R1424 47k

0

C1426

0.1

R1D08 OPEN

3.1V

0V

0V 6V 6V 6V 6V 6V 6V 6V 6V

6V 6V 6V 6V 6V 6V 6V 6V 6V 6V 6V 6V 6V 6V 6V

R1425

4.8V

3.3V

Q1407 *1

R1426 220k1k2.2k

C1427

OPEN

GND

R1D09

0

C1421

0.1

4.9V

Q1408 *10

4.8V

0.3V

R1429 470

0.1V

R1428

R1427

470

VCAVDYC

R1432

0

VCAVDYC

C1435

OPEN

C1443

0.1

C1442

0.1

C1441

0.1

C1440

0.1

2.4V 0V

0V

0V1V0V

0V

2.3V

1.1V

0.6V

0.9V

IC1403

C1449

0.1

0V0V0V0V0V

2.4V

0V

C1407

C1406

4.7

R1417 680

R1418 1k

R1407

0.1

11.8V

Q1402

*1

6.6V

1k

C1412

0.1

6.6V

R1419

C1413 120p

C1481

0.01

C1403

*1

R1405

180

C1404

220p

15p

R1406

680

L1405

C1405

120p

C1410 15p

L1406

C1411 220p

1.8V

5.2V

C1480 100

C1479

0.01

R1402

100

R1413

100

5.2V

11.8V

Q1401

8.4V

7.8V

R1404

3.3k

11.8V

Q1404 *1

7.8V

R1416

R1415

3.3k

R1D11 820

R1D12 820

R1D13 1k

12k

33k

12k

33k

No.YA064 No.YA064

DIGITAL PWB CIRCUIT DIAGRAM (1/5) SHEET 7

MAIN PWB (SHEET 3)

SHEET 6,7

SHEET 9

SHEET 8

SHEET 9

SHEET 8

SHEET 11

CN200K

QGF0508C1-50W

D_CLK2

PR[B]

CHP303-3216T

TP-PR

PR[B]7

PR[B]6 PR[B]5 PR[B]4 PR[B]3 PR[B]2 PR[B]1 PR[B]0

CHP303-3216T

TP-PB

PB[G]7 PB[G]6 PB[G]5 PB[G]4 PB[G]3 PB[G]2 PB[G]1 PB[G]0

Y[R]7 Y[R]6 Y[R]5 Y[R]4 Y[R]3

Y[R]2 Y[R]1 Y[R]0

DIVOUT

D_CLK2 D_CLK1

D_HDREF

D_CLKINV D_HOLD

VS HS

V_CLK2 V_CLK1

CLK_OUT1

HDO

VDO

I2C1A

PROGRST

SD_A

R2A34 OPEN

OPEN

K2103 NQR0351-003X

C2151

47

/16

C2152

.1

PS

K4S161622D-TC80

IC2103

R2A31

R2A30

OPEN

PS

C2153

R2A33

OPEN

R2A32

R2182R2181

R2A35

R2A36

OPEN

R2A46

OPEN

.1

PS

C2163

R2A49

C2164

R2183

OPEN OPEN

R2A50 R2A51

R2A52

OPEN

.1

R2A37 OPEN

R2184

R2A47 OPEN

.1

R2A53

OPEN

PS

OPENOPEN

OPEN

ASDD0 ASDD1

ASDD2 ASDD3

ASDD4 ASDD5

ASDD6 ASDD7

C2154

SDWE SDCAS SDRAS

SDA11 SDA10 SDA00 SDA01 SDA02 SDA3

PS

.1

C2155

C2161 47

/16

C2162

.1

PS

IC2104

K4S161622D-TC80

BSDD0 BSDD1

BSDD2 BSDD3

BSDD4

BSDD5

BSDD6 BSDD7

PS OPENOPEN

SDWE SDCAS SDRAS

SDA11 SDA10 SDA00 SDA01

SDA02

SDA3

PS

C2165

.1

PB[G]/VC

ASDD15 ASDD14

ASDD13 ASDD12

ASDD11

R2A40

ASDD10

OPEN

ASDD9 ASDD8

SDCK

SDCKE

SDA9 SDA8 SDA7

SDA6 SDA5

SDA4

BSDD15

BSDD14

BSDD13 BSDD12

BSDD11

BSDD10

R2A56 R2A57R2A48

OPEN OPEN

BSDD9 BSDD8

SDCK SDCKE

R2A58 OPEN

SDA9 SDA8 SDA7 SDA6 SDA5 SDA4

Y[R]/VY

DIGITAL PWB ASS'Y(1/5)

LCA90115-02D(FV-2003A)

No.YA064 No.YA064

R2A38 R2A39

OPEN OPEN

C2157

.1

PS

.1

C2156

OPEN

R2A42

R2A43

R2A45R2A44 OPENOPEN

R2A54 R2A55

OPEN OPEN

PS

C2167

.1

PS

.1

C2166

SDA1A

R2175

IPCB0

IPCB1

OPEN

IPCR3

GND1

K2102 NQR0351-003X

R2174

OPEN

IPCR7

IPCR6

IPCR5

IPCR4

PS

IPCR2

IPCR1

IPCR0

IPCB

IPCR

IPY

SHEET 8

C2141 47/16

D5V

IC2109

PQ1CY1032Z-W

C2190

C2191

47

/16

47

/16

D2101

R2A41 OPEN

OPEN

SD_A

SDCK SDCKE SDA9 SDA8

R2A17 100 SARY

SDA7 SDA6 SDA5 SDA4

NRZ0040-101X

BSDD8 BSDD9 BSDD10 BSDD11

NRZ0040-101X

BSDD12 BSDD13 BSDD14 BSDD15

NRZ0040-101X

BSDD7

Y[R]7 Y[R]6 Y[R]5 Y[R]4 Y[R]3 Y[R]2 Y[R]1 Y[R]0

PB[G]7 PB[G]6 PB[G]5 PB[G]4 PB[G]3 PB[G]2 PB[G]1 PB[G]0

Q2102

OPEN

BSDD6 BSDD5 BSDD4

NRZ0040-101X

BSDD3 BSDD2 BSDD1 BSDD0

NRZ0040-101X

0

R2A23

NRZ0040-0R0X

R2A24

0 NRZ0040-0R0X

R2A25

0 NRZ0040-0R0X

R2A26

0 NRZ0040-0R0X

R2A27

0 NRZ0040-0R0X

R2A28

0

NRZ0040-0R0X

DGS

R2A59

OPEN

R2A61R2A60

OPENOPEN

Q2101

R2110 R2109 OPEN OPEN

OPEN

DGS

R2112 R2111

100 100

SCL1A

R2A18 100

R2A19 100

C2128 .1

PS R2A20 100

R2A21 100

C2129 .1

PS

R2A22 100

C2130 .1

PS

C2131 .1

PS

NRZ0040-0R0X

R2A01

0

NEH71CM-476X

R2A16 R2A15

100 100

NRZ0040-101X NRZ0040-101X

PS

C2127

C2126

.1

R2A02

0

NRZ0040-0R0X

000

R2103

R2102

R2101

OPEN

R2106

R2107

R2108

OPEN

R2104

ASDD8

100

NEH71CM-476X

ASDD9

ASDD10

100

R2105

ASDD11

C2125

ASDD12

PS

.1

PS .1

C2101

R2131

ASDD13

DE5SC3ML-W

ASDD14

ASDD15

R2168

1k

100

R2113

R2114

R2115

1.8k

R2191

1.5k

MFR

NRVA63D-152X

R2193

R2192 NRVA63D-102X

MFR

L2101

39u

NQL63EM-390X

NEH70JM-107X

R2A14 100

SDA11

SDA10

SDA00

SDA01

SDA02

SDA3

NRZ0040-101X NRZ0040-101X NRZ0040-101X NRZ0040-101X

PS

C2124

R2167

.1

33

IC2101

MN82711

47

100

R2116

R2117

R2118

R2119

0

OPEN

OPEN 4747OPEN

OPEN

R2120

R2121

R2122

C2103

R2123 R2124

C2102 10P

CH

1501k

MFR

NRVA63D-151X

C2192

100

/10

C2122 10

/16

SDWE

SDCAS

SDRAS

100

R2A13

PS

R2125

.1

0

OPEN

R2127

R2126

R2128

0

R2129

C2121 .1

OPEN

R2130

C2193

100

/10

NEH70JM-107X

X2101

NAX0321-001X

PS

ASDD7

ASDD6

ASDD5

R2A12

100

OPEN

R2140

TP2101

R2141

C2104 10P

CH

ASDD4

C2123

OPEN

R2142

ASDD3

PS

.1

R2143

ASDD2

R2A11

R2144

ASDD1

100

TP2102

ASDD0

OPEN

R2145

C2120

R2146

OPEN

R2166

CH

0000000

R2147

R2165 47

0

C2119

PS

.1

C2105

R2163 C2118 OPEN OPEN

PS

.1

R2149

R2148

R2162

R2151R2150

000

C2117

OPEN

0

TP2103

CH

OPEN

C2116

K2101

NQR0351-003X

R2164 OPEN

PS

C2115 10

R2152

0

R2160 OPEN

/16

C2114

.1 PS

C2113 .1

PS

C2112

.1 PS

C2111

.1 PS

R2157

0

R2153

OPEN

C2110 C2109

10 .1

R2159

1k

R2132

1.8k

R2158

100

VOUT32

EXTG7 EXTG6 EXTG5 EXTG4

EXTG3 EXTG2 EXTG1 EXTG0

IPCB7 IPCB6 IPCB5 IPCB4

IPCB3 IPCB2 IPCB1 IPCB0

IPCR7 IPCR6 IPCR5 IPCR4

IPCR3 IPCR2 IPCR1 IPCR0

IPY7 IPY6 IPY5 IPY4

IPY3 IPY2 IPY1 IPY0

C2132

C2108 OPEN

.1

CH

PS

C2106 OPEN

R2155

OPEN

NQR0351-003X

X2102

NAX0590-001X

PS

/16

.1

0

R2161

R2A10 100 NRZ0040-101X

R2A09 100 NRZ0040-101X

R2A08 100

NRZ0040-101X

R2A07 100

NRZ0040-101X

R2A06 100

NRZ0040-101X

R2A05 100

NRZ0040-101X

R2A04 100

NRZ0040-101X

R2A03 100

NRZ0040-101X

R2154 OPEN

CH

C2107 OPEN

K2104

EXTG0

R2156

VOUT32 EXTG7 EXTG6 EXTG5 EXTG4 EXTG3 EXTG2 EXTG1

R2171

R2176

R2172

1k

OPEN

R2133

1.8k R2173

OPEN

IPCB7 IPCB6 IPCB5 IPCB4 IPCB3 IPCB2

IPCB

47

IC2102

MBV200TC90PFN03

0

C2142 .1

IPCB

IPCR

NOTE

*1

2SC2412K/QR/-X

:

*2

2SA1022/BC/-X

:

*3

MA3056/M/-X

:

*4

NQR0321-001X

:

*5

CHP303-3216T

:

*6

MA111-X

:

*7

DTC124EKA-X

:

*8

DTA144TKA-X

:

*9

MA3120WA-X

:

*10

2SA1037AK/QR/-X

:

0

NRSA63J-0R0X

:

OPEN

NON MOUNT

:

2-17 2-18

DIGITAL PWB CIRCUIT DIAGRAM (2/5) SHEET 8

CN20C7

QGG2512M1-10

FPGA

Write

SHEET 7

CTL1

CTL2

SIG_SEL

SHEET 11

VD_50

RGB

CN20C4

D_FIELD

D_CLK2

TP-HDO

MODE_SEL

VDO

*5

HDO

SUBCLK

1080_SW

TP-S2

TP-S1 *5

*5

R2230

0

R2232

0

R2233

0

R2234

100

R2236

0

SHEET 9

SHEET 7

SHEET 11

SHEET 7

QGG2512M1-10

FPGA

Write

SHEET 10

SHEET 11

3AD_SYNC

D_HS_SYN

D_CLKINV

D_HOLD

OPLL_CLK PPLL_CLK MPLL_CLK

C2211

R2257

0

NRZ0040-0R0X

R2256

0

IPCR5

C7

C2257

IPCR4

NRZ0040-0R0X

Y0C3Y1Y2Y3Y4Y5Y6Y7

0.1

PS

0.1

C2251

IPCR3

IPCR2

IPCR1

IPCR0

R2252

0

NRZ0040-0R0X

R2255

0

NRZ0040-0R0X

OPEN

TP2270

OPEN

TP2255

TP2256

R2253 R2254

00

NRZ0040-0R0X NRZ0040-0R0X

IPY7

IPY6

IPY5

IPY4

C2256

0.1 PS

IPY3

TP2269 TP2268 TP2267 TP2266

TP2265

TP2264 TP2263 TP2262

C2254

0.1 PS

TP2261

C2253

0.1 PS

TP2260 TP2259

TP2258 TP2257

PS

C2252

0.1 GND1

IPY2

IPY1

IPY0

R2258

0

C1C2C4C5C6

C0

OPEN

TP2251

TP2252

R2251

NRZ0040-0R0X

OPEN

TP2271

TP2272

IC2251

EPM3064ATC100-7

TP2254

OPEN

TP2253

0

IPCR7

IPCR6

D3.3V

K2201

NQR0351-003X

R2229

0

DPLL_COA

TP2213

TP2214

OPEN

ADC_SYNC

TP2215

C2210

0.1 OPEN

PS

OPEN

R2231

TP2219

10

TP2216 OPEN

0.1

PS

R2235

10

R2237

10

R2238

10

R2239

10

DIVOUT

IC2201

EP3064T-GMV42E

R2228

0

OPEN

TP2220

OPEN

TP2211

PS

D_HDREF

C2208

0.1

TP2210

TP2209

V_CLK1

OPEN OPEN

R2223

0

V_CLK2

VS HS

TP2208 OPEN TP2207 OPEN

0

R2225

R2220

0

R2227

PSPS

0

PS

0.1 C2209

D_CLK1

D_VSYNC

TP2212

OPEN

D_HSYNC

R2226 OPEN

R2224 OPEN R2222 OPEN

C2206

0.1

R2221 OPEN

C2205

0.1

22

C2207

/6.3

TP-V4

3.4

K2251 NQR0351-003X

TP2273

TP2274 TP2275

TP2276 TP2277

TP2278

IPCB

R2259

10

R2260

10

IPCB7 IPCB6 IPCB5 IPCB4

NRZ0040-0R0X

IPCB3 IPCB2 IPCB1 IPCB0

IPCR

OPEN

OPEN OPEN

OPEN

NRZ0040-0R0X

C2258

C2259

R2261

IPY

0.1

R2262

NRZ0040-0R0X

PS

0

DIGITAL PWB ASS'Y(2/5)

LCA90115-02D(FV-2003A)

OPEN OPEN OPEN OPEN

OPEN

OPEN OPEN OPEN

OPEN

OPEN OPEN

C

Y

C2255

/6.3

22

VDO

SHEET 9

SHEET 7

SHEET 11

CLK_OUT1

HD1

VD1

HD_50

10

0100

0

TP2201

TP2202

OPEN

R2208

R2206

R2204

R2203

TP2204

R2215

R2213

OPEN

330

OPEN

R2210

OPEN

R2214

V_VALID

V_ACTIVE

V_FIELD

PS

0

150

OPEN

0.1 R2201

R2202

R2212

10

R2211

C2204

0.1

TP2203

000

R2205

R2207

R2209

C2203

/6.3

100

PS

C2201

X2201

NAX0203-001X

No.YA064 No.YA064

R2216

V_HSYNC

TP-ACT

*5

OPEN

TP2205

0.1

PS

R2217

C2202

V_VSYNC

OPEN

R2218

TP2206

0

R2219

CLK_OUT3

TPACT

4.2

TP-V4

*5

TP-H4 *5

RM_SYNC

TP-H4

3.4

2-202-19

NOTE

OPEN

RM_SYNC

*5

CHP303-3216T

:

NON MOUNT

:

SHEET 9

DIGITAL PWB CIRCUIT DIAGRAM (3/5) SHEET 9

D5V

SHEET 11

NRZ0040-0R0X

NRSA63J-102X

TP2301 OPEN TP2302 OPEN TP2303 OPEN TP2304 OPEN TP2305 OPEN TP2306 OPEN

NRSA63J-101X

NRSA63J-0R0X

SHEET 11

SHEET 8

SHEET 7

SHEET 10

SHEET 11

SHEET 8

OPLL_CLK

PPLL_CLK

SC_RST

R2H21 R2H22 R2H23 R2H24

RM_SYNC

SCALER

Y

C

MPLL_CLK

DPLL_COA D_HS_SYN

D_FIELD D_HSYNC

D_VSYNC ADC_SYNC

RB[G]/VC

PR[B]0 PR[B]1 PR[B]2 PR[B]3

PR[B]

D_CLK2

D3.3V

R2H12 100

NRSA63J-101X

Y[R]0 Y[R]1 Y[R]2 Y[R]3

Y[R]/VY

PB[G]0 PB[G]1 PB[G]2 PB[G]3

R2H20

100 100 100

R2C92

R2C94

DB0 DB1 DB2 DB3

DB4 DB5 DB6 DB7

NRZ0040-0R0X

R2324

R2305

NRZ0040-0R0X

R2301

R2303

NRZ0040-0R0X

R2H19

1k 100

100

0

R2C93

IRQ

0

R2C89

NRZ0040-101X

RIN6 RIN3

RIN0

R2C91 NRZ0040-101X

NRZ0040-0R0X

V_HSYNC V_FIELD V_ACTIVE V_VSYNC

NRZ0040-0R0X Y0

Y1 Y2 Y3

C0 C1 C2 C3

NRZ0040-0R0X

NRSA63J-100X

R2C88

10

R2C98

10

NRSA63J-100X

NRSA63J-0R0X

100 RIN5

RIN2 GIN6 GIN2 BIN6 BIN4 BIN1

GIN5 GIN1 BIN5 BIN2

PS NCF31CZ-104X

RIN7 RIN4 RIN1 GIN7 GIN3 BIN7 BIN3 BIN0

MEM_A0 MEM_A1 MEM_A2

MEM_A3

NRZ0040-100X

Y[R]4

R2379R2364

Y[R]5 Y[R]6 Y[R]7

NRZ0040-0R0XNRZ0040-0R0X

PB[G]4 PB[G]5 PB[G]6

PB[G]7

PR[B]4 PR[B]5 PR[B]6

PR[B]7

R2C58

NRZ0040-0R0X

Y4 Y5 Y6 Y7

C4 C5 C6 C7

NRZ0040-0R0X

C2328

0.1 PS NCF31CZ-104X

C2329

0.1 PS NCF31CZ-104X

PS

TPCLKA

CHP303-3216T

NRZ0040-100X

R2320

NRZ0040-0R0X

R2302 NRZ0040-0R0X

R2C42R2C29

R2C26R2C11

C2327

0.1

NCF31CZ-104X

R2309R2308

PS

C2332 NCF31CZ-104X

C2333

MEM_A4 MEM_A5 MEM_A6 MEM_A7

1/4W

R2H47

150

NRS144J-151X

1/4W

R2H48

150

NRS144J-151X

C2345

0.1 PS

MEM_A6

MEM_A1

MEM_A5

MEM_A1

1/8WNRS181J-151X 1/8WNRS181J-151X 1/8WNRS181J-151X 1/8WNRS181J-151X 1/8WNRS181J-151X 1/8WNRS181J-151X

MEM_A5

MEM_A4

NCF31CZ-104X

MEM_A3

MEM_A2

NEH70JM-107X

MEM_A4

NCF31CZ-104X

MEM_A3CSMEM_A2

NEH70JM-107X

R2H51 R2H52 R2H53 R2H54 R2H55 R2H56 R2H62

IC2306 K4S161622D-TC80

1/8WNRS181J-151X 1/8W NRS181J-151X 1/8WNRS181J-151X 1/8WNRS181J-151X 1/8WNRS181J-151X 1/8WNRS181J-151X

R2H80

150

R2H81

150

R2H82

150

R2H83

150

R2H84

150

R2H85

150

C2358

100/6.3

C2357

PS

0.1

C2374

100/6.3

C2373

PS

0.1

GIN0

GIN4

NRSA63J-101X NRSA63J-101X

NRSA63J-101X NRSA63J-101X NRSA63J-101X

0.1

R2C84 10

NRSA63J-100X

NRZ0040-101X NRZ0040-101X

AD0

R2C71 R2C77

AD1 AD2 AD3

C2324 C2323

0.1 0.1 PS

M_DQ48

M_DQ53

M_DQ50

M_DQ52

M_DQ49

NCF31CZ-104XPSNCF31CZ-104X

M_DQ46

M_DQ43

M_DQ40

M_DQ38

M_DQ34

M_DQ29

M_DQ27

M_DQ25

R2H13

10

NRSA63J-100X

R2311

NRZ0040-100X

AD4 AD5 AD6 AD7

M_DQ55

MEM_A8 MEM_A9 MEM_A10

M_DQ51

M_DQ56

M_DQ54

CLK_OUT3

M_DQ59

M_DQ57

M_DQ58

IC2303

REMBRANDT-1A

M_DQ47

M_DQ45

M_DQ42

RD_N

CS_N

WR_N

R2C56

0

NRSA63J-0R0X

M_DQ61

M_DQ60

M_DQ39

M_DQ26

M_DQ28

M_DQ31

M_DQ35

NRZ0040-101X

R2C64

M_DQ63

V_VALID

PS

M_DQ64

M_DQ62

M_DQ66

C2319

0.1 NCF31CZ-104X

R2C48 NRSA63J-0R0X

M_DQ67

M_DQ65

M_DQ70

NRZ0040-100X

M_DQ69

M_DQ44

M_DQ41

M_DQ37

M_DQ72

M_DQ74

M_DQ68

NCF31CZ-104X NCF31CZ-104X

NCF31CZ-104X

C2307

0.1

NCF31CZ-104X

C2306

0.1

NCF31CZ-104X

M_DQ30

M_DQ22

M_DQ24

M_DQ33

M_DQ78

M_DQ71

M_DQ73

RAS WE UDQM

R2325

M_DQ77 M_DQ75 M_DQ0 M_DQ76

M_DQ1 M_DQ79 M_DQ3 M_DQ5

M_DQ4 M_DQ2 M_DQ7

M_DQ8 M_DQ6 M_DQ11 M_DQ9

M_DQ12 M_DQ10 M_DQ15

M_DQ14 M_DQ13 M_DQ18

M_DQ17 M_DQ16

M_DQ19

M_DQ21

M_DQ20 M_DQ23 M_DQ32 M_DQ36

PS

C2318

0.1 NCF31CZ-104X

NCF31CZ-104X

C2301 C2302

0.1 0.1 PS PS

NRSA63J-100X CLK

C2317

0.1

NCF31CZ-104X

C2344

0.1 PS

PQ1CY1032Z-W

IC2301

R2H32

MFR

100 NRVA63D-101X

R2H31

1k

M_DQ24 M_DQ25 M_DQ26 M_DQ27 M_DQ28 M_DQ29 M_DQ30 M_DQ31 M_DQ16 M_DQ17 M_DQ18 M_DQ19 M_DQ20 M_DQ21 M_DQ22 M_DQ23

NRZ0040-0R0X NRZ0040-0R0X NRZ0040-0R0X NRZ0040-0R0X

M_DQ48 M_DQ49 M_DQ50 M_DQ51 M_DQ52 M_DQ53 M_DQ54 M_DQ55

NRZ0040-0R0X NRZ0040-0R0X NRZ0040-0R0X NRZ0040-0R0X

R2318

R2317

R2385

R2362

R2C59

R2C44

R2C65

R2C67

MFR

NRVA63D-102X

L2303

39u

NQL63EM-390X

R2H33 330 MFR

C2339 100/6.3

NEH70JM-107X

NRVA63D-331X

GND1

C2352

0.1 PS

NCF31CZ-104X

PS

C2356

0.1 NCF31CZ-104X

C2368 NCF31CZ-104X

PS

C2372

0.1

NCF31CZ-104X

NEH70JM-107X

0.1

C2338

C2337 100/6.3

NEH70JM-107X

PS

C2314

PS

0.1 C2313

PS

0.1

PS

C2312

0.1

C2308

PS

0.1

PS

NRZ0040-100X

CS

R2351R2306

LDQM CAS BS

100/6.3

NEH70JM-107X

D2303 DE5SC3ML-W

M_DQ56 M_DQ57 M_DQ58 M_DQ59 M_DQ60 M_DQ61 M_DQ62 M_DQ63

C2340 100/6.3

GND1

C2353

0.1 PS

NCF31CZ-104X

C2369

0.1 NCF31CZ-104X

PS

M_DQ8

R2397

M_DQ9 M_DQ10 M_DQ11 M_DQ12

R2390

M_DQ13 M_DQ14 M_DQ15 M_DQ0

R2C05

M_DQ1 M_DQ2 M_DQ3 M_DQ4

R2C02

M_DQ5 M_DQ6 M_DQ7

NRZ0040-0R0X NRZ0040-0R0X NRZ0040-0R0X NRZ0040-0R0X

IC2307 K4S161622D-TC80

IC2309 K4S161622D-TC80

UDQM

LDQM

WE

UDQM

LDQMWECAS

C2348

NCF31CZ-104X

0.1 PS

R2H68 R2H73 R2H69 R2H70 R2H71 R2H72

CLK

MEM_A7

MEM_A8

MEM_A9

BS

RAS

CAS

MEM_A0

MEM_A10

CLK

MEM_A9

MEM_A8

MEM_A7

MEM_A6

BS

MEM_A0

MEM_A10

RAS

CS

DIGITAL PWB ASS'Y(3/5)

LCA90115-02D(FV-2003A)

No.YA064 No.YA064

2-21 2-22

R2H49

1/4W NRS144J-151X

150

NRS144J-151X

R2H50

150 1/4W

CLK

UDQM

MEM_A7

MEM_A4

MEM_A5

MEM_A6

MEM_A9

MEM_A8

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

1/8W NRS181J-151X 1/8W NRS181J-151X

150 150

MEM_A0

MEM_A10

150 150 150 150 150 150

R2H86 R2H87 R2H88 R2H89 R2H90 R2H91

BS

CS

WE

CAS

RAS

LDQM

NRZ0040-0R0X NRZ0040-0R0X NRZ0040-0R0X NRZ0040-0R0X

M_DQ40

R2313

M_DQ41 M_DQ42 M_DQ43 M_DQ44

R2312

M_DQ45 M_DQ46 M_DQ47 M_DQ32

R2316

M_DQ33 M_DQ34 M_DQ35 M_DQ36

R2315

M_DQ37 M_DQ38 M_DQ39

NRZ0040-0R0X NRZ0040-0R0X NRZ0040-0R0X NRZ0040-0R0X

M_DQ72

R2C14

M_DQ73 M_DQ74 M_DQ75 M_DQ76

R2C09

M_DQ77 M_DQ78 M_DQ79 M_DQ64

R2C38

M_DQ65 M_DQ66 M_DQ67 M_DQ68

R2C24

M_DQ69 M_DQ70 M_DQ71

C2380 NCF31CZ-104X

R2H57 R2H58 R2H59 R2H60 R2H61

C2349

PS

0.1 NCF31CZ-104X

MEM_A1

MEM_A2

MEM_A3

R2H74 R2H75 R2H76 R2H77

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

C2360

PS

0.1

NCF31CZ-104X

PS

C2364

0.1 NCF31CZ-104X

C2376

0.1

NCF31CZ-104X

PS

0.1

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

C2350

100/6.3

NEH70JM-107X

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

1/8W NRS181J-151X

150

C2361

0.1

NCF31CZ-104X

C2377

PS

0.1 NCF31CZ-104X

PS

IC2308 K4S161622D-TC80

IC2310

K4S161622D-TC80

UDQMBSCLK

UDQM

CASWELDQM

CLK

CASWELDQM

MEM_A9

CS

RAS

MEM_A9

BS

CS

RAS

RIN GIN

SHEET 10

BIN

RM_CLK

TPCLKBTP-H5 TP-V5

RM_CLK

RM_HSYNC

RM_VSYNC

TPCLBK

4

TP-H5

3.2

TP-V5

MEM_A4

MEM_A5

MEM_A6

MEM_A7

MEM_A8

NCF31CZ-104X

MEM_A3

MEM_A2

MEM_A1

MEM_A10

MEM_A0

NEH70JM-107X

MEM_A7

MEM_A8

MEM_A6

MEM_A5

MEM_A4

NCF31CZ-104X

MEM_A0

MEM_A1

MEM_A10

MEM_A2

MEM_A3

NEH70JM-107X

CHP303-3216T CHP303-3216T CHP303-3216T

C2366

100/6.3

C2365

0.1

C2382

100/6.3

C2381

PS

0.1

SHEET 10

PS

DIGITAL PWB CIRCUIT DIAGRAM (4/5) SHEET 10

SHEET 11

SHEET 8

SHEET 9

SHEET 8,9

SHEET 11

SHEET 9

SHEET 11

SUBCLK

RIN

GIN

BIN

D5V

33_SW

OVSYNC

D3.3V

VD1 VS_SEL RM_HSYNC RM_CLK RM_VSYNC VS_MUTE V_MUTE

RIN0 RIN1 RIN2

RIN3 RIN4 RIN5 RIN6 RIN7

GIN0 GIN1

GIN2 GIN3 GIN4 GIN5 GIN6 GIN7

BIN0 BIN1 BIN2 BIN3 BIN4 BIN5

BIN6 BIN7

R2438 R2439 R2440

R2441 R2442 R2443 R2444 R2445

R2454 R2455

R2456 R2457 R2458 R2459 R2460 R2461

R2446 R2447 R2448 R2449 R2450 R2451

R2452 R2453

IC2406

I2C1A

VPPS N.C. N.C. N.C. VPP

GND

R2411 1k

TDI

nCASC

nINIT_CONF

TDO

TMS

VCC

K2401 CE42681-001Y

GND

DATA

nCS

TCK

R2417

1k

R2412

N.C.

N.C. VCCS DCLK

1k

OE

R2416

R2414 1k

R2413 1k

CN20C6

X

R2415

1k

TPDGND

*5

R2466

10K

Q2401 2SK1374-X

R2465

TXCLK BLKH

GND1

C2437

0.1 PS

C2438

0.1 PS

10K

R2467

OPEN

R2463

SDA2A

R4 R3 R2

R1 R0 R6

DGS

100

SDA2

SCL2A

R2468 OPEN

Q2402 2SK1374-X

DGS

R2464

SCL2

TP2492 OPEN TP2491 OPEN TP2490 OPEN

SHEET 11

100

CN2201 QGA1211C2-31X

SMPS

PWB

TO PDP UNIT

I2C_RDY

SHEET 11

IC2402 IC2401 PQ1CY1032Z-W

R2402

1.5k

MFR

R2401 1k

C2401

C2442

100

/6.3

D2401

DE5SC3ML-W

R2418

1k

R2419

5.6K 0.1

TP2481

TP2482

TP2483

TP2484

TP2479

TP2480

OPEN

TP2401

OPEN

TP2402

OPEN

TP2403

OPEN

C2407

C2408

0.1 PS

C2409

TP2406

OPEN

TP2407

OPEN C2410

0.1 PS

C2411

0.1

C2412

0.1

TP2408

OPEN

TP2409

OPEN C2413

0.1

TP2410

OPEN

0.1 PS

TP2404

OPEN

TP2405

OPEN

0.1 PS

PS

0 0 0

0 0 0 0 0

0 0

0 0 0 0 0 0

0 0

L2401

MFR

39u 150

NQL63EM-390X

C2449

G7G6G5G4G3

TP2478

OPEN

R2403

MFR

C2443

C2402

100

/6.3

SCL1A

SDA1A

R2406

PS

G2

G1

G0

B7B6B5B4B3

100

R2404 R2405

100 100

IC2403

EP1K100QC2083

TP2477

OPEN

C2403

100

B2B1B0

R7R6R5R4R3R2R1

/6.3

C2404

0.01

C2446C2447C2448

0.10.10.1 PSPSPS

TA48M025F-X

IC2405

C2452

OPEN

BLKH LV_HSYNC

LV_VSYNC

RV

TXCLK

PQ3TZ53U

C2430 100

/6.3

TP-H6

*5

TP-V6

C2431

0.01

*5

100

R7 R5

LVDSSYNC

C2451

/6.3

C2450

C2406

0.01

C2405

100

/6.3

R2471

10k

Q2403

OPEN

C2445

C2444

0.1 PS

TP2457 OPEN

TP2451 OPEN

R2470

OPEN

C2428 C2429

100

/6.3

R2469

0

0.01

G

B R

I2C1A

R0

TP2469

TP2470

TP2471

TP2472

TP2473

TP2474

TP2476

TP2475

OPEN

TP2468 OPEN

TP2467 OPEN TP2466 OPEN TP2465 OPEN TP2464 OPEN

C2421

C2420

TP2463 OPEN TP2462 OPEN TP2461 OPEN TP2460 OPEN TP2459 OPEN TP2458 OPEN

C2423

0.1 PS

TP2456 OPEN TP2455 OPEN TP2454 OPEN TP2453 OPEN TP2452 OPEN

C2422

0.1 PS

TP2450 OPEN TP2449 OPEN

0.1 PS

TP2448 OPEN TP2447 OPEN TP2446 OPEN TP2445 OPEN

0.1 PS

TP2444 OPEN TP2443 OPEN

C2419

0.1 PS

G0

G1 G2 G6

G7 G3 G4

G5

C2435

0.1 PS

LV_HSYNC LV_VSYNC

LVDSSYNC

C2433

C2434

B0 B6

B7 B1 B2

B3 B4 B5 RV

C2432

0.1

PS

EPC2LC20-07-W

IC2407 THCLVDM83R-W

0.1 PS

C2436

0.1 PS

NOTE

:

*1

SCL1A SDA1A

R2408 R2409

OPEN

TP2411

100 100

OPEN

TP2412

OPEN

TP2413

OPEN

TP2414

R2410

1k

C2424

0.01

C2414

OPEN

TP2415

OPEN

TP2416

0.1 PS

OPEN

TP2417

TP2418

C2425

47p CH

OPEN

TP2419

OPEN

TP2420

OPEN

TP2421

C2441 1000p

OPEN

TP2422

C2426 1

/50

OPEN

TP2423

OPEN

TP2424

OPEN

TP2425

TP2426

M35047-069FP-X

OPEN

IC2404

OPEN

TP2427

C2415

0.1 PS PS

OPEN

TP2428

C2416

0.1

C2418

C2427

TP2429

0.1 PS

OPEN

0.1 PS

OPEN

TP2430

OPEN

TP2431

OPEN

TP2432

OPEN

TP2433

OPEN

TP2434

OSDR

OSDB

OSDG

OSDEN

OPEN

TP2435

OPEN

TP2436

OPEN

TP2437

OPEN

TP2438

OPEN

TP2439

OPEN

TP2440

OPEN

TP2441

OPEN

TP2442

OPEN

*2

*3

*4

*5

*6

*7

*8

*9

*10

0

2SC2412K/QR/-X

:

2SA1022/BC/-X

:

MA3056/M/-X

:

NQR0321-001X

:

CHP303-3216T

:

MA111-X

DTC124EKA-X

:

DTA144TKA-X

MA3120WA-XCH

:

2SA1037AK/QR/-X

:

NRSA63J-0R0X

:

NON MOUNT

:

DIGITAL PWB ASS'Y(4/5)

I2C1A

LCA90115-02D(FV-2003A)

No.YA064 No.YA064

2-242-23

DIGITAL PWB CIRCUIT DIAGRAM (5/5) SHEET 11

IC2503

SHEET 7,9,10

VIDEO SMPS

PWB

TO

PDP

UNIT

SHEET 10

QGA2501F1-12

MAIN PWB

(SHEET 5)

CN200Q

QGA2501F1-08

CN20C3

CN200J

QGF0508C1-50W

D5V

R2573

R2574 R2575 R2576

R2673

3.9k

OVSYNC

33_SW

V_MUTE

K2501

R2595 R2596 R2597 R2598 R2599 R2600 R2601 R2602

R2610 R2609 R2608 R2607 R2606 R2605 R2604

R2603

L2501

QQL26AK-220Z

NQR0351-003X

100 100 100 100

I2C_RDY

R2648

R2654

100 100 100 100 100 100 100 100

SCL1 SDA1

CL LA DA

C2502

100/10

GND

10

1/8W

10

1/8W

100 100 100 100 100 100 100 100

RI DTR CTS

RTS

DSR DCD

BA05FP-X

C2532C2529

100/10

R2506 10k

CH C2507 270p

R2594

4.7k

TCK

I2C1

PS

C2531

100/6.3

IC2504 S-80828CLNB-W

X

C2520

0.1

AUDIO

232C

*6

D2518

C2519

IC2506

TC4053BF/N/-XE

Q2514

DTC124EKA-X

R2672

IC2505

TC7W04F-X

0.1 PS

TXD

OPEN

STB5V

RXD

D2516

*6

AC_DET

TEMP_ALM

R2627 R2625 R2628

LA

STB5V

10K

R2649

C2511

100/6.3

R2530

R2531

10k

R2621

10k

R2622

NRZ0040-103X NRZ0040-103X

R2620

R2619

CS_N WR_N RD_N

10k

Q2503

DGS

SCL1

C2517

*8 Q2507

SDA1A

0.1 PS

Q2505

*8 Q2506

KEY_SCAN

R2630

10K

R2568

R2557 R2558 R2559 R2560

*8

R2570

10k

Q2510 2SK1374-X

DGS

R2539

100

SDA1

Q2504 *8

TP-32K

*5

R2540 10k

SCL1

TP-SDATP-SCL

*5*5

SDA1

R2565 R2566

R2613

100

R2571

100

R2572

100

R2563 R2564

R2577

R2578

R2579

R2580

R2581

100

330

1/8W

330 0

1/8W

330

1/8W

330

1/8W

330

1/8W

D2502

MA788-X

SW_IN0

SW_IN1

SW_IN2

SW_IN3

SCAN0

SCAN1

IC2507

RV5C386A-X

SCL1

SDA1

R2561 R2562

4.7k

GND

D2504

R2569 10k

SCL1 SDA1

D2505

*3

SCL1 SDA1

I2C1

C2534

0.1 PS

R2588

EF2506

R2589

EF2507

R2590

EF2508

R2591

EF2509

R2592

EF2510

R2593

EF2511

*6

X2502 NAX0564-001X

D2506

SCALER

0

I2C1A

R2582

X

EF2501 R2583

X

EF2502 R2584

X

EF2503 R2585

EF2504

X

R2586

X

EF2505

R2587

100

D2503 *3

0

X

0

X

0

X

0

X

0

X

0

X

D2517

MA700A-T2

R2614

R2541 R2542

*3

R2543

*3

D2507

R2544 R2545

VS_MUTE

PROGRST

100

SC_RST

100 100 100

100 100

CN200X QGA2501F1-08

CN200T QGA2501F1-06

SHEET 10

SHEET 7

SHEET 9

CN200D QGA2501F1-03

CN20C1

QGA2501F1-04

CN200V

QGA2501F1-04

(SHEET 14)

LED PWB

(SHEET 13)

CONTROL

PWB

(SHEET 14)

TEMP.

SENSOR

PWB

BATTERY

PWB

(SHEET 14)

SHEET 7,10

I2C2

SHEET 10

SHEET 9

SIG_SEL

RGB

SHEET 8

CTL2

MODE_SEL

VS_SEL

SHEET 10

CTL1

SHEET 8

1080_SW

Q2508

*8

R2662

100

R2664

4.7k

Q2511

0

100

NRZ0040-102X

R2634

1k

DTC124EKA-X

OPEN

TP2508

TP2509

AD0

AD1

AD2

IC2501

AD3

AD4

AD5

AD6

R2635

NRZ0040-102X

LED

LED_A

LED_B

LED_C

100

R2527

R2661

R2526

R2631

R2660

TP2512

100

OPEN

MB90F584-GMV42E

CTS

DSR

RTS

1k

AD7

CL

DA

OPEN

TP2504

DCD

OPEN

TP2503

DTRRITXD

R2656

RXD

100

R2521

TCK

R2517 R2516

100

R2658

TP2501

R2653

OPEN

10k

100

R2520

LED_1B

100

R2519

OPEN

TP2502

LED_1A

100

R2659

R2518

SDA1

10k

100

R2657

PS

SCL1

C2508

3.3k

R2615

SDA0

0.1

R2514

SDA1 SCL1

SCL0

R2636

6.8k

4.7k

R2513

4.7k

R2512

4.7k

R2511

4.7k

TP2505

OPEN

R2509 100

100

R2510

TP2507

OPEN

SCAN1

R2525

SCAN0

R2522

R2546

R2547

100 100

R2524

SW_IN3 SW_IN2 SW_IN1 SW_IN0

R2523

NRZ0040-101X

R2671

100

C2509

4.7K

100/6.3

R2670

4.7K

R2611

100

SCL2

SDA2

100

R2612

10k

100

IC2510

TCN75-5.0MOA-X

POWER

C2515

0.1 PS

SW_IN3 SW_IN2 SW_IN1 SW_IN0

C2510

0.1

PS

1.5k

4.7k

10k

R2528

NRZ0040-103X

IC2502

C2516

0.1 PS

R2515 R2548 R2549 R2550

AT24C64-GMV42

I2C0

AC_DET

TEMP_ALM

R2663

0

10k

X2501

CST4.00MGW

0.1

C2512

PS

R2529

10k

CS_N

R2624

WR_N RD_N

R2623

IRQ

R2626 DB0 DB1 DB2

1k

DB3 DB4 DB5 DB6

1k

DB7

DB0

DB1 DB2 DB3

R2632

NRZ0040-102X

DB4

R2633

NRZ0040-102X DB5 DB6 DB7

LED_1B

LED

C2513

0.1 PS

R2617

4.7k

R2534

100

R2535 100

IC2512 IC2513

JLC1562BF-X J LC1562BF-X

SDA0

R2553 R2554 R2555 R2556

SCL0

R2551

R2618

4.7k

100

R2629

100

R2552

10K

SDA1

LED_1B

LED_1A

LED_A

LED_B

LED_C

Q2509 2SK1374-X

R2567

OPEN OPEN

R2538

SCL1A

SCL1

R2536

4.7k

R2537

4.7k

100

SHEET 8

SHEET 8,10

SHEET 8

HD1

VD1

HD_50

VD_50

NOTE

:

*1

OPEN

*2

*3

*4

*5

*6

*7

*8

*9

*10

0

2SC2412K/QR/-X

:

2SA1022/BC/-X

:

MA3056/M/-X

:

NQR0321-001X

:

CHP303-3216T

:

MA111-X

:

DTC124EKA-X

:

DTA144TKA-X

MA3120WA-X

:

2SA1037AK/QR/-X

:

NRSA63J-0R0X

:

NON MOUNT

:

DIGITAL PWB ASS'Y(5/5)

LCA90115-02D(FV-2003A)

R2665

3.3k 1/8W

Q2512

R2666

3.3k 1/8W

R2668

10k

No.YA064 No.YA064

*1

R2667

10k

Q2513

*1

2-25 2-26

A

UDIO PWB CIRCUIT DIAGRAM SHEET 12

VIDEO SMPS PWB (TO PDP UNIT)

SP TERMINAL PWB (SHEET 14)

R9729 OPEN00OPEN

R9720

3.3K

R9722 OPEN

D9707

R9723 10K

Q9406 *1

R9719

2.2K 1/8W

R9717 680

R9721 1/8W OPEN

Q9405 *1

R9718 0

D9703 *5

RY9401 CESK024-001

R9727 OPEN

R9725 100k

R9728 150 QRK126J-151X

C9511

0.01

CN900F

QJK002-03382F

D9504 D1FS4-X

D9502 RK34-LFC4

L9604

4.7

L9601 10

QQL402K-100

R9701 1k

QQL402K-4R7

C9712

0.01

NCB31HK-103X

C9513

0.01

L9603 10

QQL402K-100

R9730R9731

C9709 470

/25

QTMN1EM-477Z

C9702 470

/25

QTMN1EM-477Z

D9702 MA3220/M/-X

R9702 1k

C9708

470

/25

QTMN1EM-477Z

C9701

470

/25

QTMN1EM-477Z

D9701

MA3220/M/-X

CN9006 QGB2033K1-08

L9602

4.7

QQL402K-4R7

C9711

0.01 NCB31HK-103X

MAIN

PWB

(SHEET 4)

CN900A

QJK002-10101A

R9724

R9726 OPEN

100k

R9604 0

R9603 0

R9605 82

C9603 47

/16

IC9601 TA8200AH

R9606 82

C9604 47

PS

PS PS

/16

PS C9605 .22

C9606 C9608 .22 .22

R9607

2.2 1/2W QRK126J-2R2X

C9607 .22

R9608

2.2 1/2W QRK126J-2R2X

LC30709-001A

C9609 C9610 47 47

/16 /16

C9611 OPEN

PS

R9609 OPEN

PS

R9610 C9612 OPEN OPEN

Q9407

330

R9707

R9733

330 1/8W

R9706

0

R9705

OPEN

IRL5602S-X

S

G

C9703 OPEN

D

R9734

IC9602

OPEN

R9708

R9709

1M

OPEN

R9712

0

R9711

0

PS

C9705

0.1 Q9403

*1

R9713 100

C9704 OPEN

R9710 OPEN

R9715

2.2K

R9714

100

R9716

2.2K

GND

C9706

4.7

Q9404 *1

C9707

4.7

NN

/50

R9601

100k

R9602

100k

C9502

0.01

C9601

4.7

C9602

4.7

NN

/50

D9705 *5

D9706 *5

C9503C9501 10001000

/25/25

R9732 1/8W

R9703

OPEN

R9704

OPEN

NOTE

OPEN

*1

*2

*3

*5

:

2SC2412K/QR/-X

:

2SA1022/BC/-X

:

MA3056/M/-X

:

MA111-X

:

NON MOUNT

R9408

R9402 10

R9401 100k

AUDIO PWB ASS'Y

LCA90183-01C(FV-9007A)

No.YA064 No.YA064

D9404 *5

R9403

10

Q9401 *2

R9404

4.7k

R9405 C9401 C9402 33k 47 47

2-282-27

D9402 *5

/16 /16

D9401 *5

R9406

10k

R9407

10k

12k

Q9402

*1

R9409 D9403 10k

MA3051/M/-X

LINE FILTER PWB CIRCUIT DIAGRAM SHEET 13

!

CN90A

C

Y9904

CH41005-H-05C

WJK0160-001A

Y9903

CH41005-H-05C

SMPS PWB (TO PDP UNIT)

!

C9907

QFZ9075-474

LF9906 OPEN

!

LF9901

QQR0810-001

Y9902

CH41005-H-05C

Y9901 CH41005-H-05C

CONTROL PWB CIRCUIT DIAGRAM SHEET 13

D4502

*5

D4501

*5

D4503

*5 *5 *5*5

QGA2501F1-06

D4504 D4505D4506

CN400T

DIGITAL PWB (SHEET 11)

D4507 *5

C9904

!

QCZ9079-222

!

C9905

QCZ9079-222

LINE FILTER

PWB ASS'Y

LCA90123-02A (FV-9005A)

! LF9902 QQR1025-001

!

LF9903

QQR1025-001

!

LF9905 QQR0810-001

!

LF9904 QQR0810-001

! C9906

QFZ9075-105

! VA9901 QAF0028-471

S4501S4502 S4503 S4504 S4507 *4*4 *4 *4 *4

CONTROL PWB ASS'Y

LCA90117-01A(FV-4004A)

LED PWB CIRCUIT DIAGRAM SHEET 13

D7604

SML-210VT-X

D7603

SML-210VT-X

D7602

SML-210VT-X

S4506 *4

S4505 *4

C7601

0.1

C7603

C7602

0.1

NOTE

*4 *5

0.1

: :

C7605

C7604

0.1

QSW0619-003Z

MA111-X

C7607

0.1

C7606

0.1

C7608

0.1

C7609

0.1

NOTE

OPEN

AC IN

*1

*2

*3

*5

2SC2412K/QR/-X

:

2SA1022/BC/-X

:

MA3056/M/-X

:

MA111-X

:

NON MOUNT

:

!

J9901 QNC0099-001

CN900H

KUM0347-001A

F9901

!

8A/250V

QMFZ041-8R0-J1

QGA2501F1-08

DIGITAL

PWB

(SHEET 11)

X

CN700X

LED PWB ASS'Y

LCA90116-01C(FV-7003A)

No.YA064 No.YA064

2-29 2-30

D7601

GL3ED8

R7601

NRSA63J-101X

IC7601

GP1U261X

100

SP TERMINAL PWB CIRCUIT DIAGRAM SHEET 14

BATTERY PWB CIRCUIT DIAGRAM SHEET 14

R7001

NRSA63J-102X

AUDIO PWB

(SHEET 12)

CN6006

QGB2033J1-08

S6001

QSW1020-001

SPEAKER

FR6001

!

QRZ9021-1R8

D6001 MA111-X

FR6002

!

QRZ9021-1R8

D6005 D6006

MA111-X MA111-X

D6007 D6008

MA111-X

L6003

4.7 QQL402K-4R7

D6002 MA111-X

D6004D6003 MA111-XMA111-X

MA111-X

C6002 OPEN

C6003 OPEN

L_OUT

R_OUT

CN600L

WJK0161-002

CN600R

WJK0161-001

SPEAKER L

SPEAKER R

DIGITAL

PWB

(SHEET 11)

CN700D

QGA2501C5-03Z

BATTERY PWB ASS'Y

LCA90121-01A(FV-7004A)

TEMP. SENSOR PWB CIRCUIT DIAGRAM SHEET 14

!

BT7001 QAB0022-001

DC OUT

J6002

QNA0030-001

OPTION

R6001 NRS181J-392X

L6013

4.7

QQL402K-4R

7

SP TERMINAL PWB ASS'Y LCA90120-01C(FV-6007A)

J6001

QNB0031-001

SPEAKER OUT

CN800V

QGA2501C5-04Z

DIGITAL PWB (SHEET 11)

C8101

0.1 PS

IC8101 TCN75-5.0MOA-X

R8103

10k

R8101

R8102

100

TEMP. SENSOR PWB ASS'Y LCA90122-01B(FV-8003A)

No.YA064 No.YA064

2-322-31

TOP

PATTERN DIAGRAMS

MAIN PWB PATTERN [SOLDER SIDE]

A

IC1209

RY1201

R1B30

R1B31

C1293

C1295

C1B22

C1253

R1B34

C1B23

R1B32 R1B33

C1255

R1255

C1260

C1262

C1259

C1250

C1249

R1262

R1260

R1261

C1273

C1261

C1288

R1263

C1275

C1263

C1268

C1287

C1272

C1274

C1258

C1285

C1248

C1277

C1280

C1284

C1179

C1281

C1282

C1283

C1180

C1181 C1182

IC1303

IC1305

C1337

C1336

X1301

C1454

R1496

C1450

C1451

R1D09

C1367

R1448

R1449

C1334

R1446

C1426

R1C08 R1C09

IC1314

R1C10 R1C11

R1440

C1439

R1439

C1438

C1446

C1456

C1370

R1C07

C1445

C1444

C1443

C1442

C1441

C1440

R1C15

R1C12

IC1318

C1371

R1C16

R1C14

IC1315

R1C13

R1C19

C1372

R1C23

IC1317

IC1316

C1373

L1302

R1C21

R1C18

R1C24

R1C22

R1C17

R1C20

L1303

E

R1D10

R1280

R1279

C1B13

C1B14

R1278

R1A27

R1A28

R1A29

R1A31

R1A30

CN1004 CN1005

CN1003

R1A32

CN1002

C1118

C1115

R1131

Q1108

RY1101

R1132

C1116

R1129 R1130

Q1109

R1134

Q1107

C1114

R1126

R1136

R1135

R1125

R1133

R1128

R1127

Q1106

C1113

C1112

R1122

Q1105

C1171

R1118

R1124

R1123

R1119

R1117

R1121

R1120

C1126 C1124 C1122

C1175 C1174 C1173

R1148 R1147

R1164 R1165

R1166 R1167

R1159

C1160

C1137

C1154

C1138

C1153

C1152

C1151

C1150

R1189

C1143

R1169 R1170 R1171 R1172 R1173 R1174 R1175

R1190 R1157

X1101

CN1001

No.YA064 No.YA064

2-33 2-34

TOP

MAIN PWB PATTERN [PARTS SIDE]

E

R1C01 R1C02

EF1401

EF1402

L1401 L1402

R1490 R1491

R1346

R1347

R1348

R1349

R1362

R1363

R1364

R1411 R1410

C1406

Q1403

R1408 C1405

Q1402

R1407 C1404

L1405

R1406

R1404

R1405

R1470

R1467

R1473

C1465

R1469

R1460

R1461

C1463

R1476

R1477

R1474

C1469

R1465 R1466

C1466

R1489

EF1403

R1488

L1412 C1468 R1478 C1470

R1479

R1480

Q1405

R1419

R1418 C1413

R1417

C1410

L1406

C1411

L1303

C1360

C1362

R1350

R1351

R1352

R1353

R1354

C1348

IC1310

R1361

R1360

R1365

C1349

R1356

C1344

C1347

C1164

C1163

R1198 R1195

R1399

R1468

C1467

R1420

EF1408

R1196

R1192

C1169

Q1118

C1165

R1184

D1103 D1104 R1105 R1106

R1104

Q1101

R1101

D1101

C1101 C1102

CN1001

IC1312

R1355

R1341

R1181

Q1119

R1193

C1166

R1103

R1102

R1A17 R1A16

C1361

R1158

Q1308

Q1112 Q1113

Q1114

R1188

R1197

R1182

Q1102

J K

C1168

IC1311

R1357

R1358

R1180

TP-HI

IC1104

R1194

R1108

R1178

R1359

C1343

R1340

IC1105

Q1115

R1107

R1A18

L1302

C1359

C1133

Q1111

C1161

C1369

Q1117

EF1404

R1183

R1A19

C1103

C1306

R1179

Q1306

C1342

R1463

C1167 R1186 R1187

R1185

D1105 D1106 R1109 R1110

R1112

Q1103

L1411 C1462 R1462

R1482

R1176

C1162

R1344

C1464

Q1412

Q1413

R1111

R1A20

C1301

IC1301

R1191

R1177

C1346

C1407

C1403 Q1401 R1401

C1473

IC1306

C1472

Q1116

R1458

C1461

C1305

C1304

C1363

IC1103

C1345

R1342 R1343

R1345

R1403

R1464

R1481

EF1409

Q1104

C1104

R1A21

C1106

C1424 R1432 C1435

R1409

C1437

TP-VI

R1487

C1408

R1116

R1426

C1420

C1302

C1303

C1307

R1425 R1424

C1421

C1422

R1423

Q1407

Q1408

C1414

Q1409

R1428

R1429

R1402

R1475

R1459

Q1411

R1416

Q1417

R1415

Q1418

C1412

C1409

TP1101

R1115

TP1102

R1413

R1412

D1107 D1108 R1113 R1114

R1430 R1431

Q1404

R1414

C1146

C1423

R1427

C1436

27

C14

Q1415

Q

TP-H2

TP-V2

K1101

X1101

C1105

C1148

C1149

C1310

1406

C1311

IC1302

C1308

C1309

EF1406

R1433

C1425

R1421

R1168

C1140

C1142 C1144 C1145

L1403

R1422

C1402

L1404

C1141

C1147

C1312

C1333

R1C03 R1C06

IC1403

R1D01

L1105

C1332

R1C05

R1C04

Q1313

R1447

R1D03

R1D02

R1162 R1161

EF1407

C1157 C1156 C1155

C1367

Q1312

R1D04

R1D06

R1163

C1401

C1119

C1334

C1418

R1D05

C1158

R1452 C1452

C1335

C1135

IC1404

R1326

R1327

C1475

R1D07

C1136

R1160 R1155 R1154

Q1110

C1460

X1301

R1328

C1477

C1448 C1447

R1D08

L1416

C1416

IC1101

C1159

R1138 R1137

C1419 R1453

R1325

L1417

D1119 C1132 R1151 R1152

C1120 R1139

C1337

C1336

R1330

R1441

C1417

C1449

IC1405

R1143 R1142 R1141

IC1305

R1329

C1458

C1459

C1453

L1410

Q1410

R1493

C1415

C1474

R1A26

C1178 C1177 C1176

R1140

R1331 R1332 R1333

R1457

L1414

R1494

C1457

C1455

R1455 R1456

R1384

X1401

R1385

L1413

R1492

R1495

IC1107

L1104

D1111

R1398

C1338

Q1307

R1388 C1368 R1386

EF1405

R1150 C1130

C1476

C1139

C1108

D1109

TPAGND

R1319

Q1304

IC1102

R1153

C1127

C1125 C1123 C1121

C1107

C1340

C1330

R1387

R1322 R1321

C1131

C1128

C1129

C1172 R1146 R1145 R1144

C1185

D1112

R1335 C1339

TP-H1

IC1304

Q1305

IC1406

D1110

R1A01

TP-V1

IC1313

R1320

C1186

R1334 R1336 R1337 R1338 R1339

C1341

R1311

R1324 C1331 R1323

C1480

D1117

C1117

D1113

R1A02

C1322

C1323

C1321

C1479

C1481

R1A24 R1A23 R1A22

R1A03

R1309

C1318

R1306

R1307

R1389

R1305

D1306

D1118

D1114

C1109

C1319

R1310

C1320

C1315

R1379

C1111

RY1101

D1301

R1308

D1305

C1184

D1115

R1312

IC1303

C1324

L1301

C1317

D1303

R1A08 R1A09 R1A10

D1302

C1316

R1301

Q1303

R1302

Q1302

R1304

C1314

R1A04 R1A05 R1A06 R1A07

D1304

Q1301

R1D12

R1D13

R1D11

C1478

C1B08

C1B07

C1183

C1B15

C1B16

D1116

C1B01

C1110

D1120

CN

1002

R1313

C1325

R1314 R1316

IC1205

R1317

C1327

C1329

IC1106

C1221

R1303

C1220

C1313

C1B02

C1B04

Q1120

R1A34

R1A33

D1121

C1187

D1201

R1206 C1209 R1205

D1203 D1204 D1205 D1206

C1326

R1B29

09

C1B

IC1206

Q1202

R1203

EF1201

C1208

R1315 R1318

R1A11

Q1211

IC1203

R1210 C1211 R1209

Q1203

R1B28

R1281

C1B03

C1328

C1279

Q1216

R1B27

C1B10

D1202

R1204

R1A15 R1A14 R1A13 R1A12

R1252

R1284

C1296

R1224 R1225

C1B11

R1229

C1215

C1B06

C1B05

R1208

R1207

C1210

EF1202

R1267

Q1204

C1278

K1201

C1286

C1291

C1B12

R1268

R1214 C1213 R1213

R1257

R1256

R1258

R1259

C1257

C1B19

R1264

R1265

R1266

TP-H3

C1222

R1285

R1223

IC1207

R1287

R1227

D1211 D1212 D1213 D1214

C1235

R1238

C1214

R1211

C1212

R1269

CN

1003

C1276

C1269

C1B20

Q1207

C1292

R1228

C1226

R1215

R1212

EF1203

C1271 C1270 C1267 C1266 C1265

C1264

C1216

R1270

R1202

Q1201

IC1208

C1256

R1272

R1273

C1204

C1253

Q1218

R1B24

R1B26

C1B18

Q1217 C1B17

C1223

R1226

R1282

R1283

C1227

D1207 D1208 D1209

Q1208

R1219

R1216

EF1204

R1218 C1217 R1217

Q1205

R1B19

R1B23

C1228

C1218

R1271

R1B17

D1220

Q1215

Q1206

C1294

R1274

C1B21

C1229

C1357

D1210

R1220

EF1205

R1222 C1219 R1221

R1275

R1286

R1390 R1376

D1309

R1371

D1311

C1238 C1237 C1236

C1201

R1288

R1201

C1203

C1202

C1205

R1276

R1277

R1299

C1207

C1206

R1B01

R1B16

D1219

C1297

C1289

C1290

IC1204

C1224

C1225

Q1309 C1356

D1314

R1372

R1366

R1367

R1368

R1370

D1313

D1312

D1307

CN1004

R1239

Q1214

R1B02

C1354

R1373

C1252 C1251

C1239

C1242

IC1201

IC1202

Q1213

R1B09

R1B06

C1355

C1254 R1254

R1240

R1241

C1243

C1245

R1242

R1243

R1B03

R1B04

R1B05

R1B13

R1B14

Q1219

R1B22

R1B20

R1B18

R1B25

R1B21

Q1209 Q1210

R1B12

R1246

R1248

R1251

R1253

R1244

R1249

R1245

R1250

R1B07

R1B08

R1B15

RY1201

C1241

R1391

C1230

R1394

Q1311

R1393

R1392

C1358

Q1310

C1353

IC1309

C1352

C1351

C1350

IC1307

D1310

D1308

R1374

R1369

R1375

CN1005

C1240

C1244

A

R1232

R1291

D1217

C1233

R1295

R1236

R1230

R1289

D1215

C1231

R1234

R1293

R1B10

R1B11

R1233

R1292

D1218

C1234

R1296

R1237

R1231

R1290

D1216

C1232

R1235

R1294

R1297

R1298

Q1212

No.YA064 No.YA064

2-362-35

TOP

DIGITAL PWB PATTERN [SOLDER SIDE]

C2437

L2501

Q

R2672

C1

D

D2517

R2588

R2589

R2590

R2591

R2592

R2593

T

C2434

C2435

C2438

C2436

C6

TP2481

R2438

R2440

R2439

R2441

Q2514

R2619

R2649

R2620 R2664

TP-32K

C2433

TP2471

TP2479

TP2480

TP2484

R2442

R2444

R2443

R2445

X2501

Q2511

R2663

TP2472

TP2473

TP2477

TP2478

TP2482

TP2483

TP2401

C2512

R2518

C2431

TP2469

TP2474

TP2475

R2625

R2529 R2530

R2531

R2517

R2519

R2510

R2513

R2667 R2668

TP2470

TP2476

TP2402

TP2403

R2516

R2509

R2514

R2665

Q2512

Q2513

R2512

R2511

R2666

R2610

TP2405

R2608

C2432

R2411

R2461 R2459 R2457 R2455

R2670

R2671

C2510

R2604

R2606

TP2406

R2416

R2460 R2458 R2456 R2454

R2611

R2612

IC2502

TP2404

R2415

R2413

R2414

R2417

R2412

TP2407

TP2451 TP2452

TP2455 TP2456

IC2403

R2452 R2453 R2450 R2451 R2448 R2449 R2446 R2447

C2360

C2361

TP2468

TP2463 TP2464

TP2465 TP2466

TP2467

TP2439

TP2433

TP2429

C2516 C2517

TP2459 TP2460

TP2461 TP2462

TP2440

TP2441

TP2434

TP2430

TP2431

TP2432

TP2427

TP2428

TP2424

TP2425

TP2421

TP2422

TP2418

TP2419

TP2416

TP2415

TP2411

TP2412

TP2409

TP2410

C2364

C2365

TP2453 TP2454

TP2457 TP2458

TP2442

TP2435

TP2426

TP2423

TP2420

TP2417

TP2413 TP2414

TP2408

TP2447 TP2448

TP2449 TP2450

TP2436

TP2437

TP2438

C2352 C2353

TP2444

TP2443

TP2445 TP2446

R2C93

R2H12

R2C48

R2C56

C2317

C2356

R2C84

R2C88

R2C92

C2332

C2327

C2323

C2308

R2305 R2324

C2344

C2345

R2C98

C2314

C2301

R2226

C2333

C2302

R2H13

R2325

C2348

R2222

R2224

C2324

R2208

R2221

C2206

C2328

C2306

R2312

C2376

C2377

R2204

R2206

C2319

C2307

C2208

R2225

R2227

R2202

C2318

C2313

C2312

R2313

R2220

R2223

C2205

R2C94

C2329

R2315

R2219

R2316

C2380

R2228

C2202

R2317

C2368

C2369

R2218

R2318

R2H49

R2229

C2209

R2385

R2362

R2H50

C2210

C2201

R2115

R2131

R2101

R2102

R2103

R2106

R2107

R2108

R2113

R2C67 R2C65

R2C44

R2C24

R2C09

R2397

R2390

C2372

R2H47

R2H48

C2373

C2211

R2118

R2121

R2114

R2C59

R2C05

R2C02

R2H85

R2207

R2209

R2123

R2126

R2119

R2120

R2C38

R2C14

R2H84

R2H56

R2203

R2205

R2141

R2128

R2122

C2103

R2H83

R2H55

C2204

R2143

R2145

R2127

R2129

R2H82

R2H54

R2148

R2150

R2130

R2H80

R2H81

R2H53

R2155

R2151

R2142

R2144

R2H52

R2154

C2107

R2147

R2149

R2H51

TP-PR

R2152

R2H68

R2H72

R2H71

R2H70

R2H69

R2174

R2175

TP-PB

C2142

R2A54 R2A56 R2A58 R2A60

C2131

C2130

C2128 C2129

C2127

C2166 R2A59 R2A61

R2A55 C2167 R2A57

C2164 R2183 R2A50

R2A52 C2165

C2126

R2171

C2125

C2162 R2A46 C2163 R2A48

C2102

R2172

R2176

C2258

C2257

C2256

Q2506

Q2505

Q2503 Q2504

R2133

R2173

R2A47 R2A49

R2184 R2A51

R2A53

C2251

C2259

C2254

TPDGND

R2166

C2123

R2A38

R2A40 R2A42 R2A44

C2253

Q2507

IC2102

C2117

R2163

C2119

C2252

R2164

R2162

C2116

R2A39 C2157

R2A41

C2156

R2A43 R2A45

C2111

C2112

C2113

C2114

R2132

R2159

R2160

C2152

R2A30

C2153 R2A32 C2154 R2181

R2A34

R2A36 C2155

C4

C2106

C2132

C2118

R2182

R2A37

R2586

R2585

R2584

R2583

R2582

X

V

R2161

C3

R2A31

R2A33

R2A35

C7

No.YA064 No.YA064

2-37 2-38

TOP

DIGITAL PWB PATTERN [PARTS SIDE]

X

C2109

X2102

R2A03

R2545

R2544

V

C2519

IC2506

C2520

K2103

R2594

R2595

C3

R2648

R2654

C7

TP2257

TP2258

R2A07

R2A09

TP2251

TP2252

TP2259

TP2260

C2110

R2602 R2601 R2600 R2599 R2598 R2597 R2596

R2251

R2253

C2534

K2104

R2156 C2108

R2157

R2A04

R2A05

R2A06

R2A08

R2A10

R2158

C2121

C2122

K2251

C2255

R2252

R2254 TP2261

D2502

D2503

R2587

EF2505

R2580

EF2504 EF2503

R2578

EF2502 EF2501

C4

C2105

TP2103

R2153

R2165

X2101

C2151

R2262

TP2253

TP2254

TP2255

TP2256

R2581

R2579

R2577

R2146

TP2262

C2191

TP2102

R2140

TP2101

C2120

R2A11

IC2103

R2260

R2261

K

C2104

R2A12

R2259

IC2109

R2124

R2125

R2167

IC2251

R2193

R2191 R2192

R2117

C2124 R2A14

R2A13

D2101

C2190

R2110

R2A15

R2168

TP2270

R2112

R2A17

TP2273 TP2272

TP2271

R2255

L2101

Q2101

IC2101

R2A16

IC2104

R2257

R2256

R2233

R2A02

R2A28

R2A26

R2A24

R2A22

R2A20

R2A18

R2258

TP2269

R2234

R2235

C2193

R2116

R2A21

R2A19

C2141

TP2277

TP2278

C2161

TP2267

TP2268

TP2264

TP2265

R2236

R2237

C2192

C2101

C2115

K2102

TP2275

TP2276

R2H77

R2H76 R2H75

TP2266

TP2263

R2238

R2239

R2105

R2104

K2101

TP2274

R2H57

C2207

R2109

R2111

R2A01

R2A27

R2A25

R2A23

R2H73

R2H58

K2201

TP-HDO

TP-S1

Q2102

R2H86

R2H74

R2H59

C2203

R2556 R2555

R2554 R2553

R2515 R2548 R2549

R2550

R2566 R2565

R2564 R2563 R2557

R2558 R2559 R2560

R2H87

TP-S2

R2231

R2H88

R2H89

R2H60

R2H90

R2H61

TP2215

R2232

TP2216

X2201

R2H91

R2H62

TP2219

R2230

R2201

R2212

TP2201 TP2202

TP2203 TP2204

TP2213

TP2214

R2210

R2211

TP2304

TP2305

C2374

TP2220

TP2212

TP-ACT

TP2211

TP-H4

TP2303

IC2303

IC2309

TP-V4

C2381

IC2201

R2213

R2214

R2215

R2216

C2382

TP2210

TP2209

TP2206 TP2205

R2217

C2337

TP2301

TP2302

R2311

C2338

TP2208 TP2207

R2H23

R2H24

R2309

IC2310

C2349

D2303

R2H22

R2H21

R2308

IC2301

TP2306

R2H19

R2H20

R2351

C2350

C2339

R2306

R2H31

R2H32

L2303

R2H33

C2340

TPCLKA

IC2306

C2357

R2401 R2402

C2442 C2401

TPCLKB

TP-H5

C2358

TP-V5

R2C77

R2C71

R2C29 R2C11 R2364 R2301 R2302

R2C91

R2C64

R2C58

R2303

IC2307

D2401

C2402

R2C89

R2C42

R2536

R2C26

R2379

R2320

IC2401

R2551

R2552

C2366

R2561

IC2513

IC2402

R2537

R2562

J

R2662

C2449 R2419 R2418 R2403

L2401

C2443

C2405

C2403

IC2308

Q2508

C2414

IC2512

R2656 R2521 R2658 R2520 R2659

R2657

R2525 R2524

C2420

C2415

R2527 R2526 R2661 R2660 R2631

R2546

R2547

R2603

C2451

C2419

C2422

C2418

C2416

C2413

C2406

C2404

IC2406

R2522

R2605

TP-H6

C2411

C2412

R2628

R2621 R2622

R2653

R2571

R2613

R2607

C2421

C2410

R2627

TP2502

C2509

R2572

R2609

TP-V6

C2409

R2634 R2635

TP2501

C2508

C2513

C2423

C2408

C2450

R2623 R2624

R2626

R2632

R2633

IC2502

C2428

C2444

C2407

C2531

R2471

R2469

R2406

R2404

X2501

IC2501

R2618

R2534

C2446

C2447

C2532

C2426

R2535

C2429

C2430

C2445

R2405

C2425 C2424

R2617

IC2405

CN2201

C2452

C6

C2448

IC2503

C2427

C2502

IC2404

R2410

R2408

R2409

C2441

C2507

TP2503

R2615

TP2505

R2523

IC2510

C2515

Q2403

R2470

Q2509

R2629

R2630

IC2504

R2506

TP2508

TP2512

TP2504

TP2507

C2529

Q2510

R2538 R2567

TP2509

D2516

R2528

D2504

IC2407

R2464

R2468

R2463

R2467

IC2505

R2539 R2568

C2511

EF2507 EF2508

EF2509

EF2510

Q2402

Q2401

X2502

R2570

R2540

R2569

TP2490

TP2492

K2501

D2505

D2506

D2507

D2517

IC2507

TP2491

R2466

R2465

K2401

L2501

R2573 R2574 R2673 R2575 R2576 D2518

R2541

R2542

R2543

D

R2614

TP-SCL

TP-SDA

EF2506

EF2511

Q

C1

T

No.YA064 No.YA064

2-402-39

T

PC TERMINAL PWB PATTERN [SOLDER SIDE] PC TERMINAL PWB PATTERN [PARTS SIDE]

A

J5502 J5503

C5501

L5502

CN5503

L5501

R5513

R5511

J5502

CN5503

J5501

CN5504

CN5505

J5503

FRON

J5506

J5504

J5507

C5522

C5531

J5506

L5510

C5532

J5504

L5511

R55

R5541 R5542

R5544

R5543

C5521

R5547 R5553

EF5501

54

R5532

C5511

R5531

R5533

D5512 D5511

D5513

D5501

R5525

R5526

R5527

R5528

R5524

R5523

CN5505

R5522

C5541

R5521

J5501

CN5504

R5508

R5507

R5506

R5505

R5504

C5502

R5503

R5512

R5501

R5502

R5514

FRON

V TERMINAL PWB PATTERN [SOLDER SIDE]

D5201

EF5202

CN5001

J5003

EF5201

R5214

R5213

R5211

C5201

R5212

R5201

L5201

R5202

J5005

C5202

L5202

EF5101

J5001 J5002

R5101

R5102

R5104

R5103

R5105

R5106

C5101

L5101

C5102

L5102

R5308

R5307

EF5304 EF5305

CN5002

J5007

R5306

R5305

J5006

R5304

R5303

R5302

R5312

R5301

C5302

R5313

R5314

R5311

C5301

L5301

L5302

R5205 R5206

J5008

R5203 R5204

J5004

EF5203

R5207

R5315

FRON

V TERMINAL PWB PATTERN [PARTS SIDE]

J5003

J5002

J5001

J5005

J5004

CN5001

J5008

J5006

J5007

CN5002

FRON

No.YA064 No.YA064

2-41 2-42

OPTOP

A

UDIO PWB PATTERN [SOLDER SIDE]

AUDIO PWB PATTERN [PARTS SIDE]

R9733

C9511

C9702

A F

C9709

D9702

C9708

D9701

D9703

C9701

R9727

R9725

RY9401

R9734

R9728

R9731

R9726

R9724

Q9405

R9730

Q9407

R9718

R9717

R9729

C9711

R9721 R9719

D9707

L9601

L9602

R9720 R9722 R9723

Q9406

C9603

R9701

C9503

C9502

R9602

C9601

R9601

C9604

D9705

R9603

R9605

R9609

C9611

D9502 D9504

C9513

R9732

D9706

IC9601

CN9006

C9501

C9602

H9601

C9609

C9605

R9606

R9604

L9603

R9610

C9612

C9610

C9606

C9607

R9702

R9715

Q9403

C9706

R9713

R9705

R9704

L9604

R9707

C9608

R9607

R9706

R9708

C9703

R9608

R9402

R9703

R9709

Q9402

C9712

D9404

R9407

C9705

R9409

R9404

R9401

D9403

IC9602

Q9401

D9402

D9401

R9406

R9408

R9403

R9711

R9712

C9707

R9405

C9401

C9704

R9714

C9402

R9710

Q9404

R9716

C9402

C9707

R9608

C9401

L9603

L9604

C9610

R9607

C9609

C9706

C9501

C9604

CN9006

D9502

C9602

IC9601

L9601

L9602

C9601

C9503

C9603

R9728

RY9401

C9701

C9709

H9601

C9708

C9702

A

F

T

SP TERMINAL PWB PATTERN [SOLDER SIDE] SP TERMINAL PWB PATTERN [PARTS SIDE]

FR6002

CN600R

D6008

D6007

C6003

D6005

D6006

CN600R

FR6002

J6002

CN600L

C6002

D6004

S6001

D6003

D6001 D6002

FR6001

L6003

L6013

J6001

J6002

R6001

CN6006

FRONT FRONT

CN6006

J6001 L6003

L6013

FR6001

S6001

CN600L

No.YA064 No.YA064

2-442-43

OP

OPTOP

OP

T

LED PWB PATTERN [SOLDER SIDE]

LINE FILTER PWB PATTERN

X

IC7601

D7601

T

LED PWB PATTERN [PARTS SIDE]

T

D7601

D7602

D7604

D7603

IC7601

R7601

C7609

X

C7601

BATTERY PWB PATTERN [SOLDER SIDE] BATTERY PWB PATTERN [PANEL SIDE]

D

R7001

BT7001

FRONT FRON

BT7001

D

LF9901

LF9902

LF9903

Y9904

Y9902

Y9901

LF9906

Y9903

LF9905

AC

C9904

C9907

LF9904

TEMP. SENSOR PWB PATTERN [SOLDER SIDE] TEMP. SENSOR PWB PATTERN [PANEL SIDE]

V

IC8101

C8101

R8103

R8102 R8101

V

CONTROL PWB PATTERN [SOLDER SIDE]

D4507

S4507

T

D4505

D4506

D4504

S4501

D4501

S4502

D4502

S4504 S4505 S4506

S4503

D4503

CONTROL PWB PATTERN [PARTS SIDE]

T

FRON

TOP

C9905

C9906

H

VA9901

F9901

J9901

S4501 S4502 S4503

S4504

S4505 S4506 S4507

T

FRON

No.YA064 No.YA064

2-45 2-46

SERVICE MANUAL

PLASMA DISPLAY MONITOR

YA064B20048

BASIC CHASSIS

GM-V42C/BT

Supplementary

The following items for the GM-V42C/BT was changed partly from GM-V42C. Therefore, this service manual describes only the items which differ from those of the GM-V42C service manual. For details other than those described in this manual, please refer to the GM-V42C service manual (No.YA064, 2004/3).

OUTLINE

T4

Since the production place was changed, we have issued the SERVICE MANUAL for GM-V42C/BT.

HOW TO IDENTIFY MODELS

“GM-V42CBT” is added at the bottom of the Rating label.

Indicated

"GM-V42CBT"

No.YA064B

2004/8

DIFFERENCE LIST

EXPLODED VIEW PARTS LIST -1 (Page 3-3)

 Ref. No.

GM-V42C GM-V42C/BT

 100 LC10528-017A LC10528-017A-0K FRONT PANEL ASSY Inc.No.101-102

Part No.

PART NAME DESCRIPTION

EXPLODED VIEW PARTS LIST -2 (Page 3-5)

 Ref. No.

GM-V42C GM-V42C/BT

11 LC11594-001B LC11594-001B-0K BACK BRACKET

15 LC11652-001D LC11652-001D-0K CHASSIS BASE

 20 LC21362-001B LC21362-001B-0K PC TERMINAL BKT

 24 LC21296-001D LC21296-001D-0K AV TERMINAL BKT

 28 LC21313-002A-0L LC21706-001A-0L ROLL R LABEL

Part No.

PART NAME DESCRIPTION

PACKING PARTS LIST (Page 3-18)

 Ref. No.

GM-V42C GM-V42C/BT

Part No.

PART NAME DESCRIPTION

1 LC21040-002B LC21711-001A-H PACKING CASE(TOP)

2 LC21039-001C LC21710-001A-H

3 LC11610-001C LC12044-001A-H CUSHION ASSY

12 QPA02503505P CP30966-001-H POLY BAG

19 LC20989-001A-H LVL-GMV42CB CORNER LABEL

22 --- LC42036-001A THAILAND LABEL Addition

23 --- LC42036-002A THAILAND LABEL Addition

24 --- LC42036-003A THAILAND LABEL Addition

25 --- LC42036-004A THAILAND LABEL Addition

PACKING CASE(BOTTOM)

1-2 (No.YA064B)

PACKING (Page 3-19)

10

11

16

Addition

12

13 14 15

8

3

4

9

4

22

Addition

5

1

23

Addition

24

Addition

18

25

17

18

6

7

18

3

2

19

21

17

18

20

19

(No.YA064B)1-3

Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY VIDEO DISPLAY CATEGORY 12, 3-chome, Moriya-cho, kanagawa-ku, Yokohama, kanagawa-prefecture, 221-8528, Japan

(No.YA064B)

Printed in Japan

WPC

PLASMA DISPLAY MONITOR

MENU INPUT

GM-V42C

INSTRUCTIONS

LCT1616-001A 0204MKH-MW-VP

INSTRUCTIONS

Model GM-V42C

Thank you for purchasing this JVC Monitor. Before using the monitor, read this manual carefully so that you know how to use the Monitor correctly. Refer to this manual whenever questions or problems about operation arise. Be sure to read and observe the safety precautions. Keep this manual where the user can see it easily. * Installation and removal require special expertise.

Consult your product dealer for details.

Safety Precautions

IMPORTANT INFORMATION

WARNING:TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPARATUS TO RAIN, MOISTURE, DRIPPING OR SPLASHING AND THAT NO

OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE

APPARATUS.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measure.

IMPORTANT SAFEGUARDS

Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order not to defeat the safeguards incorporated into this product, observe the following basic rules for

its installation, use and service. Please read these “Important Safeguards” carefully before use.

– All the safety and operating instructions should be read before the product is operated.

– The safety and operating instructions should be retained for future reference.

– All warnings on the product and in the operating instructions should be adhered to.

– All operating instructions should be followed.

– Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

– Use a vacuum cleaner to get rid of the dust around the intakes (all the

openings) on the rear. If a vacuum is not available, use a cloth and wipe it off. Failure to do so will cause internal heat buildup and, therefore, cause damage to the product.

– Do not use attachments not recommended by the product manufacturer as

they may be hazardous.

– Do not use this product near water. Do not use immediately after moving from

a low temperature to high temperature, as this causes condensation, which may result in fire, electric shock, or other hazards.

– Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious

injury to a child or adult, and serious damage to the product. The product should be mounted according to the manufacturer’s instructions, and should use a mount recommended by the manufacturer.

– When the product is used on a cart, care should be taken to avoid quick stops, excessive force, and

uneven surfaces which may cause the product and cart to overturn, damaging equipment or causing possible injury to the operator.

– Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and

protect it from overheating. These openings must not be blocked or covered. (The openings should never be blocked by placing the product on bed, sofa, rug, or similar surface. It should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s instructions have been adhered to.)

For proper ventilation, separate the product from other equipment, which may prevent ventilation and keep distance more than 10 cm.

– This product should be operated only with the type of power source indicated on the label. If you are not sure of the

type of power supply to your home, consult your product dealer or local power company.

2

– Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or

against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where they exit from the product.

– For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods

of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power line surges.

– Do not overload wall outlets, extension cords, or convenience receptacles on other equipment as this can result in a

risk of fire or electric shock.

– Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short

out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

– Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltages

and other hazards. Refer all service to qualified service personnel.

– Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions:

a) When the power supply cord or plug is damaged.

b) If liquid has been spilled, or objects have fallen on the product.

c) If the product has been exposed to rain or water.

d) If the product operated normally by following the operating instructions. Adjust only those controls that are covered

by the Operation Manual, as an improper adjustment of controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

e) If the product has been dropped or damaged in any way.

f) When the product exhibits a distinct change in performance – this indicates a need for service.

– When replacement parts are required, be sure the service technician has used replacement parts specified by the

manufacturer or with same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

– Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to

determine that the product is in proper operating condition.

– The product should be placed more than 30 cm away from heat sources such as radiators, heat registers, stoves, and

other products (including amplifiers) that produce heat.

– When connecting other products such as VCR’s, and personal computers, you should turn off the power of this product

for protection against electric shock.

– Do not place combustibles behind the cooling fan. For example, cloth, paper, matches, aerosol cans or gas lighters that

present special hazards when over heated.

– Use only the accessory cord designed for this product to prevent shock.

– Do not touch the handles on the rear soon after many hours of continuous use. They are so hot and will cause a burn on

the hand. If you need to touch the handles, for example, to move the product, wait until the handles are cooled enough.

Option terminal: This terminal is intended exclusively to be used to drive the fan motor.

–

Do not connect any plugs to the terminal other than JVC’s recommended optional parts.

Polarity of terminal

POWER CONNECTION

The power supply voltage rating of this product is AC 220 V. Do not use other power cords than the power cord attached to this unit.

3

Parts Identification

VIDEO

DISPLAY

OFF POWER

RM–C579 REMOTE CONTROL UNIT

ON

ASPECT

MUTING

MENU/EXIT

VOLUME

A

COMPO.

/(RGB B)

B RGB A

INPUT SELECT

VIDEO

DISPLAY

OFF POWER

RM–C579 REMOTE CONTROL UNIT

ON

ASPECT

MUTING

MENU/EXIT

VOLUME

A

COMPO.

/(RGB B)

B RGB A

INPUT SELECT

12

3

49

p

6

8

7

5

REGULAR FULL

ZOOMPANORAMIC

Remote Control

1 Remote control cable jack (page 11)

Connect the remote control cable (not supplied) when using this remote control as a wired remote control.

2 Remote signal transmission window

3 POWER ON/OFF button (page 14)

Use this button to turn on and off (on standby) the Monitor when the POWER switch on the rear of the Monitor is “| (on).”

4 DISPLAY button (page 14)

Use this button to display the input terminal, color system (for VIDEO A or VIDEO B input), scan system (for COMPONENT input) and horizontal/vertical frequency (for RGB A and RGB B input).

5 INPUT SELECT (VIDEO A, VIDEO B, COMPO./(RGB B) and

RGB A) buttons (page 14)

Use these buttons to switch between inputs. To select the COMPONENT or RGB B input, you have to set “RGB/COMPO.” correctly on the menu (see page 22).

6 MUTING button (page 14)

7 2 / 3 / 5 / ∞ buttons

8 MENU/EXIT button

9 ASPECT button (page 15)

p VOLUME + / – buttons (page 14)

Use this button to turn off the volume immediately. Pressing the button again will resume the previous volume level.

Use these buttons to select menu items or make adjustments.

Use this button to display or erase menus. While a sub-menu is displayed, pressing this button will move you one screen back to the preceding menu.

Use this button to switch between aspect ratios. Each time you press the button, the aspect ratio changes as follows:

Use these buttons to adjust the volume level.

4

Monitor: Front View

MENU INPUT

3456

12

Bottom View

1 Remote sensor/power lamp

Point the front end of the wireless remote control toward here. When the Monitor is turned on, the power lamp glows green. It glows orange in standby mode.

2 Self-diagnostic lamps (page 39)

These lamps light/flash if something abnormal occurs with the Monitor.

3 2 / 3 / 5 / ∞ buttons

Use these buttons to select menu items and to make adjustments.

• When no menu is displayed, you can use the 2 / 3

buttons to adjust the volume level.

4 MENU button

Use this button to display or erase menus. While a sub-menu is displayed, pressing this button will move you one screen back to the preceding menu.

5 INPUT button (page 14)

Use this button to switch between inputs. To select the COMPONENT or RGB B input, you have to set “RGB/COMPO.” correctly on the menu (see page 22).

button (page 14)

6

Use this button to turn on and off (on standby) the Monitor when the POWER switch on the rear of the Monitor is “| (on).”

5

Parts Identification (Continued)

AC INAUDIO

L

OUT

R

RGB A

AUDIO

IN

REMOTE

RS-232C

WIRED

MAKE

EXTERNAL

(

9

(

R

SPEAKER OUT

L

INTERNAL

POWER

OPTION

1 2 3 4 5

7

8

6

Monitor: Rear Views

1 RGB A input terminals (page 11)

Input terminal (D-sub, 15 pin)

Connect to the video output terminal of a personal computer.

Note:

• Use a cord as short as possible when connecting a personal computer to this terminal. (Recommended length is within 3 m.)

AUDIO IN terminal (stereo mini jack)

Connect to the audio output terminal of a personal computer.

2 REMOTE terminals (pages 11 and 13)

RS-232C terminal (D-sub, 9 pin)

Connect to the RS-232C terminal of a personal computer. For the control method using this terminal, consult an authorized JVC dealer.

MAKE terminal (mini DIN, 4pin)

Connect an external control unit. (See page 13.)

WIRED terminal (stereo mini jack)

Connect a wired remote control unit to this terminal.

Note:

• When the above three terminals are used at the same time, transmitted commands through the MAKE terminal have priority over those through the other

6

terminals.

3 AUDIO OUT terminals (pin jack) (page 11)

Connect to the audio input terminals of external equipment such as an amplifier.

4 AC IN terminal (page 11)

Connect the supplied power cord to this terminal.

5 POWER switch (page 14)

6 OPTION terminal (page 13)

When this switch is set to “| (on),” you can turn on and off (on standby) the Monitor by using the POWER button on the remote control or the

Connect the power cord of the Cooling Fan Unit (not supplied) when installing the Monitor vertically.

button on the Monitor.

7 SPEAKER OUT L/R terminals (page 11)

Connect external speakers, such as unique JVC speakers (not supplied), etc.

8 INTERNAL/EXTERNAL (built-in speaker/external

speaker) selecting switch (page 11)

INTERNAL: To use built-in speakers. EXTERNAL: To use external speakers.

9 VIDEO A terminals (option) (page 12)

9 p q

VIDEO A

VIDEO

IN OUT

AUDIO

L/MONO

R

VIDEO B

VIDEO

IN Y/C IN

COMPONENT/RGB B

VIDEO

Y/G Pb/B Pr/R HD/Cs VD

AUDIO

L/MONO

R

AUDIO

L/MONO

R

AUDIO (L/MONO, R) input terminals (pin jack)

Connect these terminals to the audio input terminals of a VCR, etc.

VIDEO IN terminal (BNC)

Connect this terminal to the video output terminal of a VCR, etc.

VIDEO OUT terminal (BNC)

Connect this terminal to the video input terminal of another Monitor, etc.

Note:

• Since the video output terminals on this Monitor are

loop-through terminals, the devices connected to this video output terminal should be correctly terminated. Otherwise, pictures become abnormally bright or the Monitor screen gets affected abnormally.

p VIDEO B terminals (option) (page 12)

AUDIO (L/MONO, R) input terminals (pin jack)

Connect these terminals to the audio output terminals of a VCR, etc.

Y/C (S video) IN terminal (mini DIN 4pin)

Connect this terminal to the S-video output terminal of a VCR, etc.

VIDEO IN terminal (pin jack)

Connect this terminal to the video output terminal of a VCR, etc.

Note:

• When both the video and S-video terminals are

connected, the S-video terminal will have priority.

q COMPONENT/RGB B input terminals (option) (page 12)

AUDIO (L/MONO, R) input terminals (pin jack)

Connect these terminals to the audio output terminals of the other equipment.

G, B, R, HD/Cs, VD (VIDEO) input terminals (BNC)

Connect these terminals to the following output terminals of a personal computer or other equipment: – Analog RGB signal output terminals – Horizontal sync (HD) signal or composite (Cs) signal

output terminal

– Vertical sync (VD) signal output terminal

Notes:

• External sync signals are automatically detected when they come in.

• When both horizontal (HD)/vertical (VD) sync and composite (Cs) sync are connected, HD/VD sync signals will be used.

Y, Pb, Pr (VIDEO) input terminals (BNC)

Connect these terminals to the component signal output terminals of NTSC or high-vision equipment.

Note:

• When these terminals are used as the component terminals (Y, Pb, Pr)—see “Setting the COMPONENT/ RGB B Input” on page 22, external sync signals (HD/Cs, VD) cannot be used.

7

Preparations

Checking the Accessories

The following accessories are included with the Monitor. Check for them. If any item is missing, please contact the dealer where you purchased the Monitor.

• Remote control (RM-C579) x 1

• Power cord x 1

• Batteries (AA/R6P) x 2

• Ferrite core x 1

Installing the Batteries

Put the batteries in the remote control as follows. If the remote control has become erratic in operation, change the batteries.

1

Remove the back cover.

While pushing the release lever on the cover, remove the cover in the direction of the arrow.

2

Place the batteries.

Put the two supplied batteries (AA/R6P), noting the ª and · markings, as shown.

3

Replace the back cover as illustrated.

Make sure the release lever on the cover is locked in place correctly.

Precautions for using batteries

If batteries are used improperly, the liquid could leak out, causing a fire, injury, etc. or dirtying the vicinity. Take notice of the following:

• Do not mix old and new batteries.

• Do not mix different types of battery as different types may have different characteristics.

• Place the batteries according to the ª and · markings indicated on the battery compartment.

• When installing the batteries, insert the · end first to avoid a short circuit.

• Use only the specified batteries.

• When you are not using the remote control for a long time, remove the batteries.

• When the batteries have reached the end of their life, replace them with new ones immediately. Otherwise, the liquid may leak out, or malfunction may be caused by the leaked liquid. If the leaked liquid contacts your skin, wipe off the liquid with a soft cloth. If the affected skin is left as is, you may get a rough skin.

• Do not throw the batteries into fire or try recharging them.

• The service life of batteries is six months to one year for normal use. The supplied batteries are only for checking the operation and their life may be shorter. When the remote control operation becomes erratic, replace with new batteries.

Attaching the Ferrite Core

Attach the ferrite core to the power cord. Using the power cord without the ferrite core may lead to noise (interference). Open the ferrite core, insert the power cord and close the ferrite core. Attach the ferrite core to the AC IN end of the power cord.

Ferrite core

Power cord

Plug to AC IN

8

Installation

50

200

MENUINPUT POWER

100

200

150

50

MENUINPUT POWER

150

50

200

Precautions

• When mounting the Monitor vertically, consult your dealer. (See also page 13.)

• When installing the Monitor, be sure to use a dedicated Stand Unit, Wall Mounting Unit, or Monitor Hanger Unit, depending on a particular case. Ask your dealer for installation.

• When installing the Monitor, refer also to the user manual for each option to use. Do not tilt the Monitor rightward, leftward, or backward.

• Route the power cord and connection cables along wall or floor corners to avoid walking on them.

• For good heat dissipation, try to leave the following distances of space (minimum) around the Monitor.

• The ambient temperature of the installation place should be within the range of 0˚C to 40˚C (slightly variable depending on ambient conditions for installation.)

• When installing the Monitor in a place, such as near the ceiling, the remote control may not work correctly because of possible effects from the surroundings. If this happens, use the remote control as a wired remote control or move the Monitor where it is free from these effects.

When installing the Monitor on a stand

Front View

Side View

Wall

Unit: mm

Take measures against the Monitor from overturning:

To protect against abnormal events such as earthquakes and to prevent unexpected accidents, take appropriate measures for preventing the Monitor from overturning; should it overturn, this could lead to personal injury. For detailed information, refer to the manual supplied for the stand.

When mounting the Monitor on the wall

Front View

Side View

When hanging the Monitor from the ceiling

Side View

Unit: mm

Notes:

• Do not allow the same image (pattern) to be continuously displayed on the screen for a long time; otherwise, the area on the screen corresponding to the image may vary in brightness, leaving an afterimage on the screen. To reduce the afterimage, you can use the Refresh function (see page 31).

• The Monitor is manufactured using very high-precision technology, allowing for more than 99.99% active pixels, however, be aware that only a slight number of pixels may be deficient or lit at all times.

• Do not install the Monitor in such a way that the Monitor and other AV equipment affect each other adversely. (For example, if a disturbed image or noise due to electromagnetic interference occurs, or if the infrared remote control malfunctions, change the installation place.)

Unit: mm

9

Connections

Precautions

• Before making connections, turn off all the equipment.

• Use a cord whose plugs are correctly matching for the terminals on this Monitor and the equipment.

• Plugs should be firmly inserted; poor connection could cause noise.

• To unplug a cord, be sure to grasp its plug and pull it out.

• Connect the power cord after having finished all other connections.

• Refer also to the user manual of each piece of equipment.

Available Signals

Video signals (option)

The following signals can be input to this Monitor:

• VIDEO A and VIDEO B terminals accept — PAL, PAL60, NTSC, NTSC4. 43, and SECAM signals.

• COMPONENT/RGB B terminals accept — 480i, 576i, 480p, 576p, 720/60p, 1080/60i (1035/60i), and 1080/50i signals. (You

need to set “RGB/COMPO.” to “COMPO.” on the menu (see page 22).

Computer signals (Preset)

This Monitor has 18 preset video modes for the most popular industrial standard, and the signals of the following image resolutions can be input to the RGB input terminals.

Signal name Scan systemNo.

1 PC98 640 400 24.8 56.4 Non-interlace

2 VGA400-70 640 400 31.5 70.1 Non-interlace

3 VGA480-60 640 480 31.5 59.9 Non-interlace

4 VGA480-72 640 480 37.9 72.8 Non-interlace

5 VGA480-75 640 480 37.5 75.0 Non-interlace

6 WVGA-60 852 480 31.7 60.3 Non-interlace

7 MAC13” 640 480 35.0 66.7 Non-interlace

8 SVGA-56 800 600 35.2 56.3 Non-interlace

9 SVGA-60 800 600 37.9 60.3 Non-interlace

10 SVGA-72 800 600 48.1 72.2 Non-interlace

11 SVGA-75 800 600 46.9 75.0 Non-interlace

12 XGA-60 1024 768 48.4 60.0 Non-interlace

13 XGA-70 1024 768 56.5 70.1 Non-interlace

14 XGA-75 1024 768 60.0 75.0 Non-interlace

15 XGA-85 1024 768 68.7 85.0 Non-interlace

16 XGA+-75 1152 864 67.5 75.0 Non-interlace

Screen resolution

Horizontal

Vertical

Horizontal

Frequency (kHz)

Vertical

Frequency (Hz)

17 RGB15K-60 — — 15.7 59.9 Interlace

18 RGB15K-50 — — 15.6 50.0 Interlace

Notes:

• When a signal other than listed above is input, a part of the screen may become void or an unnecessary picture may appear.

• Signals, though they are within the acceptable range of frequencies, may not be displayed normally, depending on the signal type.

• Depending on the connected equipment, the Monitor may not be compatible with composite sync (Cs) or G on sync signals.

• When a preset mode signal is input, the vertical frequency displayed on the screen will have an “*” shown at its right top position.

• When the No. 6 signal is input, change the aspect ratio to “FULL” with the ASPECT button (page 15) on the remote control or from the “FUNCTION SELECT” menu (page 21).

• When No. 8 to No. 16 signals are input, thin lines may become obscure for their signal frequencies are higher than the screen resolution.

10