TO PREVENT FIRE OR SHOCK HAZARDS, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
About the installation place
Do not install the projector in a place that cannot
support its weight securely.
If the installation place is not sturdy enough, the
projector could fall or overturn, possibly causing
personal injury.
WARNING:
THIS APPARATUS MUST BE EARTHED.
CAUTION:
To reduce the risk of electric shock, do not remove
cover. Refer servicing to qualified service personnel.
This projector is equipped with a 3-blade grounding
type plug to satisfy FCC rule. If you are unable to
insert the plug into the outlet, contact your electrician.
NOISE EMISSION DECLARATION
The sound pressure level at the operator position is
equal or less than 60dB(A) according to ISO7779.
WARNING
This equipment is compliant with Class A of CISPR
32.
In residential environment this equipment may
cause radio interference.
WARNING
REMOVE THE LENS COVER BEFORE TURNING
ON THE PROJECTOR
FCC INFORMATION (U.S.A. only)
CAUTION:
Changes or modification not approved by JVC could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful interference
to radio communications. Operation of this
equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own
expense.
Getting Started
.
2
PORTABLE CART WARNING
(symbol provided by RETAC)
S3126A
-
-
-
-
-
-
-
-
-
-
-
-
-
IMPORTANT SAFEGUARDS
Electrical energy can perform many useful functions.
This unit has been engineered and manufactured to
assure your personal safety. But IMPROPER USE
CAN RESULT IN POTENTIAL ELECTRICAL
SHOCK OR FIRE HAZARD. In order not to defeat
the safeguards incorporated into this product,
observe the following basic rules for its installation,
use and service. Please read these Important
Safeguards carefully before use.
All the safety and operating instructions should be read
before the product is operated.
The safety and operating instructions should be retained for
future reference.
All warnings on the product and in the operating
instructions should be adhered to.
All operating instructions should be followed.
Place the projector near a wall outlet where the plug can be
easily unplugged.
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
Do not use attachments not recommended by the product
manufacturer as they may be hazardous.
Do not use this product near water. Do not use immediately
after moving from a low temperature to high temperature,
as this causes condensation, which may result in fire,
electric shock, or other hazards.
Do not place this product on an unstable cart, stand, or
table. The product may fall, causing serious injury to a child
or adult, and serious damage to the product. The product
should be mounted according to the manufacturer’s
instructions, and should use a mount recommended by the
manufacturer.
When the product is used on a cart,
care should be taken to avoid quick
stops, excessive force, and uneven
surfaces which may cause the product
and cart to overturn, damaging
equipment or causing possible injury to
the operator.
Slots and openings in the cabinet are
provided for ventilation. These ensure reliable operation of
the product and protect it from overheating. These
openings must not be blocked or covered. (The openings
should never be blocked by placing the product on bed,
sofa, rug, or similar surface. It should not be placed in a
built-in installation such as a bookcase or rack unless
proper ventilation is provided and the manufacturer’s
instructions have been adhered to.)
To allow better heat dissipation, keep a clearance between
this unit and its surrounding as shown below. When this unit
is enclosed in a space of dimensions as shown below, use
an air-conditioner so that the internal and external
temperatures are the same. Overheating can cause
damage.
-
-
-
-
-
-
-
-
a)
b)
c)
d)
e)
f)
When the power supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen on the
product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the
operating instructions. Adjust only those controls that
are covered by the Operation Manual, as an improper
adjustment of controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to normal operation.
If the product has been dropped or damaged in any
way.
When the product exhibits a distinct change in
performance, this indicates a need for service.
Power source indicated on the label. If you are not sure of
the type of power supply to your home, consult your
product dealer or local power company.
This product is equipped with a three-wire plug. This plug
will fit only into a grounded power outlet. If you are unable
to insert the plug into the outlet, contact your electrician to
install the proper outlet. Do not defeat the safety purpose of
the grounded plug.
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them. Pay particular attention to cords at doors,
plugs, receptacles, and the point where they exit from the
product.
For added protection of this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent damage to
the product due to lightning and power line surges.
Do not overload wall outlets, extension cords, or
convenience receptacles on other equipment as this can
result in a risk of fire or electric shock.
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltages
and other hazards. Refer all service to qualified service
personnel.
Unplug this product from the wall outlet and refer service to
qualified service personnel under the following conditions:
Front
150 mm
and above
200 mm
and above
300 mm
and above
300 mm
and above
150 mm and above
Getting Started
.
3
-
-
-
-
-
-
-
-
-
-
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or with same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
The product should be placed more than one foot away
from heat sources such as radiators, heat registers, stoves,
and other products (including amplifiers) that produce heat.
When connecting other products such as VCR’s, and DVD
players, you should turn off the power of this product for
protection against electric shock.
Do not place combustibles behind the cooling fan. For
example, cloth, paper, matches, aerosol cans or gas
lighters that present special hazards when over heated.
Do not ceiling-mount the projector to a place which tends to
vibrate; otherwise, the attaching fixture of the projector
could be broken by the vibration, possibly causing it to fall
or overturn, which could lead to personal injury.
Use only the accessory cord designed for this product to
prevent shock.
Once every three years, please perform an internal test.
This unit is provided with replacement parts needed to
maintain its function (such as cooling fans). Estimated
replacement time of parts can vary greatly depending on
frequency of use and the respective environment. For
replacement, please consult your dealer, or the nearest
authorized JVC service center.
When fixing the unit to the ceiling, Please note that we do
not take any responsibility, even during the warranty period,
if the product is damaged due to use of metal fixtures used
for fixation to the ceiling other than our own or if the
installation environment of said metal fixtures is not
appropriate. If the unit is suspended from the ceiling during
use, please be careful in regard to the ambient temperature
of the unit. If you use a central heating, the temperature
close to the ceiling will be higher than normally expected.
Video images can burn into the electronic component parts.
Please do not display screens with still images of high
brightness or high contrast, such as found in video games
and computer programs. Over a long period of time it might
stick to the picture element. There is no problem with the
playback of moving images, e.g. normal video footage.
-
Not using the unit for a long time can lead to malfunction.
Please power it on and let it run occasionally. Please avoid
using the unit in a room where cigarettes are smoked. It is
impossible to clean optical component parts if they are
contaminated by nicotine or tar. This might lead to
performance degradation.
* DO NOT allow any unqualified person to
install the unit.
Be sure to ask your dealer to install the unit
(e.g.attaching it to the ceiling) since special
technical knowledge and skills are required for
installation. If installation is performed by an
unqualified person, it may cause personal injury or
electrical shock.
-
-
-
-
-
-
-
Do not use optical instruments (such as magnifying glass or
reflector) viewing the laser output. It may pose an eye
hazard.
When turning on the projector, ensure that no one is looking
into the projection lens.
Do not look into the lens and openings when the light is on.
Doing so would have serious effects on the human body.
Do not detach or attach the projection lens with the power
connected.
Attempting to disassemble, repair or modify the projector
yourself may lead to serious safety issues.
Using a faulty product not only results in electrical shock or
fire hazard, it can cause visual impairment.
When abnormality occur, stop using the projector
immediately and send it to your authorized dealer for repair.
Getting Started
.
4
Power cord
Power cord
For European continent countries
Green-and-yellow
Blue
Brown
: Earth
: Neutral
: Live
POWER CONNECTION
WARNING:
WARNING:
Do not cut off the main plug from this
equipment.
The power supply voltage rating of this product is
AC100V – AC240V. Use only the power cord
designated by our dealer to ensure Safety and EMC.
Ensure that the power cable used for the projector is
the correct type for the AC outlet in your country.
Consult your product dealer.
If the plug fitted is not suitable for the power points
in your home or the cable is too short to reach a
power point, then obtain an appropriate safety
approved extension lead or adapter or consult your
dealer. If nonetheless the mains plug is cut off,
dispose of the plug immediately, to avoid a possible
shock hazard by inadvertent connection to the main
supply.
THIS APPARATUS MUST BE EARTHED.
IMPORTANT (Europe only):
The wires in the mains lead on this product are
colored in accordance with the following cord:
As these colors may not correspond with the
colored making identifying the terminals in your
plug, proceed as follows:
The wire which is colored green-and-yellow must be
connected to the terminal which is marked M with
the letter E or the safety earth or colored green or
green-and-yellow. The wire which is colored blue
must be connected to the terminal which is marked
with the letter N or colored black.
The wire which is colored brown must be connected
to the terminal which is marked with the letter L or
colored red.
For USA and Canada only
Use only the following power cord.
Dear Customer,
This apparatus is in conformance with the valid
European directives and standards regarding
electromagnetic compatibility and electrical safety.
European representative of
JVC KENWOOD Corporation is:
JVCKENWOOD Deutschland GmbH
Konrad-Adenauer-Allee 1-11,
61118 Bad Vilbel,
GERMANY
Getting Started
.
5
ENGLISH
Information for Users on Disposal of Old Equipment and Batteries
[European Union only]
These symbols indicate that equipment with these symbols should not be disposed
of as general household waste. If you want to dispose of the product or battery,
please consider the collection systems or facilities for appropriate recycling.
Notice:
The sign Pb below the symbol for batteries indicates that this battery contains lead.
Benutzerinformationen zur Entsorgung alter Geräte und Batterien
[Nur Europäische Union]
Diese Symbole zeigen an, dass derartig gekennzeichnete Geräte nicht als normaler
Haushaltsabfall entsorgt werden dürfen. Wenden Sie sich zur Entsorgung des
Produkts oder der Batterie an die hierfür vorgesehenen Sammelstellen oder
Einrichtungen, damit eine fachgerechte Wiederverwertung möglich ist.
Hinweis:
Notification:
Das Zeichen Pb unterhalb des Batteriesymbols gibt an, dass diese
Batterie Blei enthält.
Informations relatives à l’élimination des appareils et des piles usagés, à l’intention des utilisateurs
[Union européenne seulement]
Si ces symboles figurent sur les produits, cela signifie qu’ils ne doivent pas être jetés
comme déchets ménagers. Si vous voulez jeter ce produit ou cette pile, veuillez
considérer le système de collecte des déchets ou les centres de recyclage appropriés.
La symbole Pb en dessous du symbole des piles indique que cette
pile contient du plomb.
Informatie voor gebruikers over het verwijderen van oude apparatuur en batterijen
[Alleen Europese Unie]
Deze symbolen geven aan dat apparatuur met dit symbool niet mag worden
weggegooid als algemeen huishoudelijk afval. Als u h
et product of de batterij wilt
weggooien, kunt u inzamelsystemen of faciliteiten voor een geschikte recycling
gebruiken.
Opmerking:
Het teken Pb onder het batterijsymbool geeft aan dat deze batterij lood bevat.
Battery
Products
Batterie
Produkte
Pile
Produits
Batterij
Producten
DEUTSCH
FRANÇAIS
NEDERLANDS
Información para los usuarios sobre la eliminación de baterías/pilas usadas
[Sólo Unión Europea]
Estos símbolos indican que el equipo con estos símbolos no debe desecharse
con la basura doméstica. Si desea desechar el producto o batería/pila, acuda
a los sistemas o centros de recogida para que los reciclen debidamente.
Atención: La indicación Pb debajo del símbolo de batería/pila indica que ésta
contiene plomo.
Baterías/pilas
Productos
ESPAÑOL / CASTELLANO
ITALIANO
Informazioni per gli utenti sullo smaltimento delle apparecchiature e batterie obsolete
[Solo per l’Unione Europea]
Questi simboli indicano che le apparecchiature a cui sono relativi non devono
essere smaltite tra i rifiuti domestici generici. Se si desidera smaltire questo
prodotto o questa batteria, prendere in considerazione i sistem i o le strutture di
raccolta appropriati per il riciclaggio corretto.
Nota:
Il simbolo Pb sotto il simbolo delle batter ie indica che questa batteria contiene piombo.
Batteria
Prodotti
Getting Started
.
6
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This Projector is classified as a CLASS 3R LASER PRODUCT.
This CLASS 3R LASER PRODUCT label and Caution label is located on the
Rear Side surface of the projector.
For the customers In the U.S.A. and Canada
CAUTION
Location information of the labels
LASER CAUTION LABEL
The APERTURE LABEL is located on the top cover.
APERTURE LABEL
APERTURE LABEL
IEC62471-5 LABEL
LASER RADIATION AVOID DIRECT EYE EXPOSURE CLASS 3R LASER PRODUCT.
Do not look into the lens while in use.
Light source specifications
30 W Laser diodes ×6
Wavelength 450 - 460 nm
Maximum output is 64.12 W
WARNING
Beam divergence angle from lens of this unit
Laser emission port
Wide : α=71°
Tele : α=39°
α
CAUTION
LASER RADIATION
AVOID DIRECT EYE
EXPOSURE
CLASS 32 LASER PRODUCT
WAVE LENGTH : 453nm
MAX OUTPUT : 83.56mW
RAYONNEMENT LASER
EVITER L’EXPOSITION
DIRECTE DES YEUX
PRODUIT LASER DE CLASSE 3R
LONGUEUR D'ONDE : 453nm
SORTIE MAX : 83.56mW
RADIACION LASER
EVITAR LA EXPOSICION
DIRECTA DE LOS OJOS
CLASE 3R PRODUCTO LASER
LONGGITUD DE ONDA : 453nm
SALIDA MAX : 83.56mW
IEC/EN60825-1:2007
LASER APERTURE
LASER APERTURE
Getting Started
.
7
Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
For the customers In other countries
CLASS 1 LASER PRODUCT
Location information of the labels
LASER CAUTION LABEL
Do not look into the lens while in use.
WARNING
CAUTION
LASER CAUTION LABEL
IEC62471-5
Location information of the labels
As with any bright light source, do not stare into the beam, RG2 IEC 62471-5:2015
Power cord (for USA) (about. 2 m) ......................................... 1 piece
Power cord (for EU) (about. 2 m) ............................................ 1 piece
0
Be sure to read the “Safety Precautions” before using this projector.
.
.
.
10
Controls and Features
A
B
C
DD
E
Main Unit - Front
.
Getting Started
A
Lens (optional)
Zoom lens or short focal length lens is optional.
B
Remote Sensor (front)
aim the remote control at this area when using
Please
it.
* There is also a remote sensor at the rear.
Main Unit - Bottom
C
Indicator
Refer to “Indicator Display on the Main Unit”P. 62.
D
Exhaust vent
Warm air is discharged to cool down the internal
temperature.
Do not block the vents.
E
Feet
The height and angle of the projector can be adjusted by turning the
foot. (0 to 5 mm) (
When the foot is removed, it can be used as the mounting hole for the
ceiling mount bracket.
P. 20)
11
Main Unit - Rear
I
J
H
FG
[MENU]: Displays the menu
[BACK]: Returns to the previous menu
[JKHI] keys: Selects an item
[OK]: Confirms a selection
[J INPUT K]: Switches the input
A: Turns “on”/“off” the
power
Getting Started
.
F
Input terminals
details on the terminals. refer to “Main Unit - Input
For
Terminals”P. 13.
G
Operation panel
For more details, please refer to the “Operation
panel” in the diagram below.
H
Remote Sensor (rear)
Please aim the remote control at this area when using
it.
* There is also a remote sensor at the front.
Operation panel
.
I
Power input terminal
Connect the supplied power cord to this terminal.
J
Air Inlets
The inlets take in air to cool down the internal
temperature.
not block the inlet. Do not blow hot air on the inlet.
Do
Doing so may cause the unit to malfunction.
12
Main Unit - Input Terminals
ABCDGEFHI
Enlarged View of Rear Face
.
Getting Started
A
[SYNC OUT] terminal
For synchronizing with other equipment.
B
[SERVICE] terminal
For updating the software using a commercially
available USB flash drive.
C
[RS-232C] terminal (D-sub 9-pin
male)
projector can be controlled by connecting a PC to
The
this terminal.
D
[LAN] terminal (RJ-45)
The projector can be controlled by connecting it to a
PC through the computer network for control
commands to be sent to the projector.
E
[DisplayPort 1] input terminal
F
[DisplayPort 2] input terminal
G
[DisplayPort 3] input terminal
H
[DisplayPort 4] input terminal
(20-pin male)
For connecting to devices that support DisplayPort
output. (
I
P. 21)
[REMOTE CONTROL] terminal
(stereo mini jack)
This terminal is used to connect the remote control
directly to the projector with the cable.
13
Remote Control
INPUT 1
DISPLAYPORT
INPUT 2DUAL
NATURAL
DYN AMIC
INPUT 4INPUT 3QUAD
3D
FORMAT
PIC.
ADJ.
COLOR
TEMP.
GAMMA
USER5USER6USER4
USER2USER3USER1
LENS
CONTROL
MOTION
ENHANCE
C.M.D.
NAME
EDIT
A
M
O
P
Q
E
H
B
C
D
F
G
I
J
K
L
N
Getting Started
A
B [STAND BY]
Turns off the power. (
B
C [ON]
Turns on the power. (P. 23)
C
[DISPLAYPORT]
Switches the input to [DisplayPort 1]
to [DisplayPort 4], [Dual] or [Quad].
(P. 23)
D
[LENS CONTROL]
For adjusting focus and zoom.
(P. 33)
E
[C.M.D.]
For setting frame interpolation.
(P. 31)
0
Pressing the button each time
switches the mode in the following
sequence: “Off” " “Mode 1” "
“Mode 2” " “Mode 3”...
F
[MOTION ENHANCE]
Switches the Motion Enhance
setting. (P.
G
[HIDE]
Hides the image temporarily.
(P. 23)
H
[LIGHT]
Illuminates the buttons on the
remote control.
I
[JKH I] keys
For selecting an item.
J
[OK]
Confirms a selected item.
K
[MENU]
Displays the menu, or hides the
menu if it is displayed.
L
[BACK]
Returns to the previous menu.
31)
P. 24)
M
[PICTURE MODE]
Switches the picture mode. (P. 27
0
Press [NATURAL], [DYNAMIC] or
[USER1] to [USER6] to switch to the
respective picture mode.
0
Pressing [NAME EDIT] enables the
name of the picture mode from
[USER1] to [USER6] to be edited.
N
[GAMMA]
Switches the gamma. (P. 30)
0
Pressing the button each time
switches the configurable gamma in
sequence.
O
[COLOR TEMP.]
Switches the color temperature.
(P. 29)
0
Pressing the button each time
switches the configurable color
temperature in sequence.
P
[LENS AP.]
For setting the aperture. (P. 27)
Q
[PIC. ADJ.]
Displays the picture quality
adjustment gauge. (P. 31)
0
Pressing the button each time
displays the adjustment gauge in
the following sequence: “Contrast”
" “Brightness” " “Color” " “Tint” "
“Sharpness” " “LD Current” "
“Aperture” " “Picture
Level” " “Bright Level”.
Tone” " “Dark
)
14
Loading Batteries into the Remote Control
30°
30°
20°
20°
Remote Control
This unit
A
B
30°
30°
20°
20°
20°
20°
20°
20°
Screen
Remote Control
This unit
0
Loading the batteries
.
If the remote control has to be brought closer to the
to operate, it means that the batteries are wearing
unit
out. Replace the batteries with new ones (AAA).
0
Insert the batteries according to the t s marks.
Be sure to insert the s end first.
When removing the battery, do so from the t end.
0
If an error occurs while using the remote control,
remove the batteries and wait for five minutes. Load
the batteries again and operate the remote control.
Removing the batteries
.
Effective Range of Remote Control Unit
Getting Started
When aiming the remote control toward the sensor on this
(front or rear), ensure that the distance to the sensor
unit
is within 7 m.
If the remote control fails to work properly, move closer
to this unit.
Control through reflection off a screen, etc.
Ensure that the total of distance A (between this unit and
the screen) and distance B (between the remote control
and the screen) is within 7 m.
* As the efficiency of signals reflected from the remote
control unit varies with the type of screen used, the
operable distance may decrease.
.
CAUTION
0
Do not put the remote control in a place with an exposure to direct sun light or high temperature.
It may deformed due to heat, or the internal components may be adversely affected resulting in fire hazard.
0
Remove the batteries from the remote control when storing the remote control.
Storing the remote control for a prolonged period without removing the batteries can cause battery leakage.
.
15
Menu
ABCDEF
Getting Started
Select the icon at the top of the menu to display its corresponding
setting item as shown below.
A
Picture Adjust
.
B
Input Signal
.
C
Installation
.
D
Display Setup
.
E
Function
.
F
Information
.
16
Installing the Projector
Front
150 mm
and above
200 mm
and above
300 mm
and above
300 mm
and above
150 mm and above
Screen
Front
Precautions during Installation
Please read the following carefully before installing this
unit.
When carrying this unit
This unit is heavy in weight. Please ensure that there are
at least two persons carrying it.
Do not install at the following
This unit is a precision device. Please refrain from
installing
it may cause fire or malfunction.
0
0
0
0
0
0
* This unit produces a great amount of heat, and is
*
or using it at the following locations. Otherwise,
Dusty, wet and humid places
Places subject to oily smoke or cigarette smoke
On top of a carpet or bedding, or other soft surfaces
Places exposed to direct sunlight
Places with a high or low temperature
Do not install this unit in a room that is oily or subject
cigarette smoke. Even a small quantity of smoke or
to
oiliness can have a long-term impact on this unit.
designed to take in cool air to cool its optical
components. Using the unit at the above locations
may cause dirt to attach to the light path, thereby
resulting in dark images or dull colors.
Dirt that sticks to the optical components cannot be
removed.
Maintain clearance from the wall, etc.
As the unit discharges a large amount of heat, install it
with
adequate clearance from the surroundings as shown
below.
.
Leave the front area of the unit unblocked.
If there is any obstructing object in front of the exhaust
vent,
hot air will flow back to the unit and cause it to heat
up. Hot air flowing out of the unit may cast shadows on
the screen (heat haze phenomenon).
Installing the screen
Install the unit and the screen such that they are
perpendicular to each other.
Set up
Using the projector
There is no particular limitation on the positioning of the
projector during installation.
You can install at your preferred angle.
.
0
Please choose a screen material with non-uniform
patterns.
Uniform patterns such as checks may cause
interference patterns to occur.
0
this case, you can change the size of the screen to
In
make the interference patterns less noticeable.
Using the projector at a high altitude
When using this unit at a location that is higher than 900
m above sea level (low air pressure), set the “High
Altitude Mode” to “On”. (P.
41)
17
Precautions during Mounting
C
A
B
D
E
4 Locations
Securing (mounting) the projector
Set up
.
0
When
this unit is to be mounted to a fixed position for
use, install it horizontally.
0
Make sure to secure the main unit to prevent
accidents such as during an earthquake.
Securing with screws
.
Remove the four feet at the bottom, and fasten using the
screws (M5 screws, 15 to 25 mm).
* Using
* Do not use 2 adjacent locations (A+B, B+C, C+D, D
screws other than those designated may cause
the unit to break down.
+E) only.
18
Securing the projector (ceiling mount)
A
*1
Rear
Front
Rear
Front
.
0
Be sure to ask your dealer to install the unit for you.
Installing the unit on your own may cause the unit to
fall resulting in injury.
0
Take the necessary actions to prevent the main unit
from falling off such as during an earthquake.
0
Regardless of the warranty period, JVC is not liable
any product damage caused by mounting the unit
for
with non-JVC ceiling fittings or to an environment that
is not suited for ceiling mount.
0
When using the unit with it suspended from a ceiling,
pay attention to the surrounding temperature. When
a heater is in use, the temperature around the ceiling
may be higher than expected.
0
attach the unit to the ceiling mount bracket, set the
To
torque between the range of 1.5N m to 2.0N m.
Tightening with torque exceeding the above range
may cause damage to the unit, which may result the
unit to fall.
0
When reusing the ceiling mount bracket of an old
consult the specialist to check if there are any
model,
issues with the surrounding space and increase in
weight.
0
the outlet at an accessible height to unplug from
Install
the wall. Or install the circuit breaker at an accessible
height to shut down the projector. If you need
information, please consult your authorized dealer or
specialist.
Installing the ceiling mounting bracket
A
Remove the rear foot (x2).
0
The
removed feet can be installed to the rear holes.
(*1)
0
It is not necessary to remove the front feet.
However,
when they are removed.
B
Install
indicated by the arrows.
0
Use screws that meet the specification.
0
For details, contact your authorized dealer.
it will not pose any usage problems even
.
the ceiling mounting brackets to the screw holes
.
Set up
19
Adjusting the Position
ContractExtend
Feet
4 Locations
Adjusting the elevation angle of the projector
The height and inclination of the unit (0 to 5 mm) can be
adjusted by turning the feet.
Lift the unit and adjust the four feet.
.
Set up
.
20
Connecting the Projector
DisplayPort Terminal
This Unit
PC, etc.
DisplayPort Cable (Sold Separately)
To [DisplayPort 1] to [DisplayPort 4]
Input Terminals
Desktop PC, etc.
Server
Hub
Network
Connection Cable
(Sold Separately)
This Unit
To [LAN] Terminal
0
Do not turn on the power until connection is complete.
0
The connection procedures differ according to the device used. For details, please refer to the instruction manual
of the device to be connected.
0
This projector is used for projecting images. To output the audio of connected devices, please connect a separate
audio output device, such as an amplifier or speaker.
0
Some cables cannot be connected to this unit due to the size of their connector cover.
Connecting to the DisplayPort Terminals
.
0
For
single-channel input signals, connect to one of the [DisplayPort 1], [DisplayPort 2], [DisplayPort 3] or [DisplayPort
4] input terminals.
0
For two-channel input signals, connect to the [DisplayPort 1] and [DisplayPort 3] input terminals.
0
For four-channel input signals, connect to the [DisplayPort 1] to [DisplayPort 4] input terminals.
Æ “Types of Possible Input Signals” (P.
0
Video images may not appear if a cable that does not support HBR2 is used. Use a cable that supports HBR2.
0
When disconnecting the DisplayPort cable, make sure to remove the latch and unplug the cable.
57)
Set up
Connecting to the LAN Terminal
.
0
The network is used to control this unit. It is not used for sending or receiving video signals.
0
Please contact your network administrator for information concerning the network connection.
0
For more information on control, please refer to “External Control”P.
50.
21
Connecting to the RS-232C Terminal
RS-232C Terminal
Laptop, etc.
RS-232C Connection
Cable (Sold Separately)
To [RS-232C] Terminal
This Unit
This Unit
Wired Remote
Controller
(Sold Separately)
Connection Cable
(Sold Separately)
To [REMOTE] Terminal
A
B
Power Cord
(Supplied)
Set up
.
0
For more information on control, please refer to “External Control”P. 50
Connecting to the REMOTE Terminal
.
0
For more details on the wired remote controller and connection cable, please consult your dealer.
.
0
0
0
0
0
0
22
Connecting the Power Cord (Supplied Accessory)
A
Connect
the main unit
B
Insert the supplied power plug into the wall outlet.
Precautions to prevent fire and electric shock
The power consumption of this unit is large. Please connect it directly to the wall outlet.
When you are not using the projector, please unplug the power cord from the outlet.
Connect it using only the power cord supplied.
Do not use a voltage other than the indicated power voltage.
Do not damage, break or modify the power cord. Do not place a heavy object on the power cord, or heat or pull it.
Doing so may damage the power cord.
Do not unplug the power cord with wet hands.
the power cord supplied to the power input terminal on
Viewing Videos
LIGHTWARNING
STANDBY/ON
LIGHTWARNING
STANDBY/ON
AN
AN
When LD block is starting up
“STANDBY/ON” lights up (green)
In standby state
“STANDBY/ON” lights up (red)
STANDBY/ON
LIGHT
WARNING
INPUT 1
DISPLAYPORT
INPUT 2 DUAL
INPUT 4INPUT 3QUAD
1
1 32
2
3
This unit
Remote Control
MEMO
0
Connect the power cord, and ensure that the “STANDBY/ON” indicator
lights up in red.
1
Turn on the power
Remote control: press the C [ON] button
Projector unit: press the A button
.
2
Choose the image to project
Remote control:
ButtonTerminal
[INPUT 1]DisplayPort 1
[INPUT 2]DisplayPort 2
[INPUT 3]DisplayPort 3
[INPUT 4]DisplayPort 4
[DUAL]Dual (*1)
[QUAD]Quad (*2)
*1, *2: Refer to “Types of Possible Input Signals”P. 57
Projector unit: press the [INPUT] button to switch the input
0
Play back the selected device to project the image.
Operate
To hide the image temporarily
Press the [HIDE] button on the remote control
0
The “STANDBY/ON” indicator light starts to blink in green. When “LED
Indication” is set to “Off”, the indicator does not blink.
0
Press the [HIDE] button again to resume display of the image.
0
The power cannot be turned off when the image is temporarily hidden.
23
3
LIGHTWARNING
STANDBY/ON
LIGHTWARNING
STANDBY/ON
In standby state
“STANDBY/ON” lights up (red)
In the Cool-down mode
“STANDBY/ON” blinking (red)
0
Operate
The power cannot be turned off within approximately 30 seconds after it has been turned on.
0
The power cannot be turned on again while cooling is in progress (10 seconds).
0
Pull out the power plug when the unit is not to be used for a prolonged period of time.
0
If
Turn off the power
Remote control: press the B [STAND BY] button
Projector unit: press the A button
0
While the “Are you sure you want to turn off?” message is displayed, press the button again.
0
light of the LD block goes off, and the “STANDBY/ON” indicator switches from a green light to a red blinking
The
light.
0
the light goes off, the fan will run for about 10 seconds to cool down the LD block (Cool-down mode). Do
After
not disconnect the power cable while cooling is in progress.
0
After about 10 seconds, the “STANDBY/ON” indicator switches from a blinking red to a solid red light.
.
CAUTION
the indication of indicator differs from the description, refer to “Indicator Display on the Main Unit”P. 62 for details.
24
Adjustments and Settings in the Menu
Pressing the [MENU] button displays the menu.
Press the [JKH I] keys to select an item, followed by pressing the [OK] button to confirm the selection.
List of Menu Items
Picture Adjust
I Picture Mode ...................................................................................................................................................
9 Sharpness .................................................................................................................................................. P. 27
9 DLC ............................................................................................................................................................. P. 27
9 Auto Intensity .............................................................................................................................................. P. 27
9 LD Current .................................................................................................................................................. P. 27
9 Aperture ..................................................................................................................................................... P. 27
9 User Name Edit .......................................................................................................................................... P. 28
I Color Management .......................................................................................................................................... P. 28
I Color Temp. ..................................................................................................................................................... P. 29
I Gamma ............................................................................................................................................................ P. 30
I Blur Reduction ................................................................................................................................................. P. 31
9 Clear Motion Drive ...................................................................................................................................... P. 31
9 Motion Enhance ......................................................................................................................................... P. 31
I Contrast ........................................................................................................................................................... P. 31
I Brightness ....................................................................................................................................................... P. 31
I Color ................................................................................................................................................................ P. 31
I Tint .................................................................................................................................................................. P. 31
P. 27
Adjust/Set
Input Signal
I Input Level ....................................................................................................................................................... P. 32
I Color Space ..................................................................................................................................................... P. 32
I Channel Hide ................................................................................................................................................... P. 32
25
Installation
I Lens Control ....................................................................................................................................................
9 Focus ......................................................................................................................................................... P. 33
9 Zoom .......................................................................................................................................................... P. 33
9 Image Pattern ............................................................................................................................................. P. 33
I Pixel Adjust ...................................................................................................................................................... P. 34
9 Adjust ......................................................................................................................................................... P. 34
9 Adjust Area ................................................................................................................................................. P. 34
9 Adjust Color ................................................................................................................................................ P. 34
9 Adjust Pattern ............................................................................................................................................. P. 34
9 Adjust Pattern Color ................................................................................................................................... P. 34
9 Adjust (Pixel) .............................................................................................................................................. P. 34
9 Adjust (Fine) ............................................................................................................................................... P. 34
9 Reset .......................................................................................................................................................... P. 34
I Mask ................................................................................................................................................................ P. 38
I Distortion Correction ........................................................................................................................................ P. 38
I Edge Blending ................................................................................................................................................. P. 40
I Installation Style ............................................................................................................................................... P. 40
I LED Indication ................................................................................................................................................. P. 41
I High Altitude Mode .......................................................................................................................................... P. 41
Display Setup
I Back Color .......................................................................................................................................................
I Menu Position .................................................................................................................................................. P. 41
I Signal Display .................................................................................................................................................. P. 41
I Logo ................................................................................................................................................................ P. 41
Adjust/Set
P. 33
P. 41
Function
I Off Timer ..........................................................................................................................................................
I Network ........................................................................................................................................................... P. 42
I Remote Code .................................................................................................................................................. P. 43
I Hide Mode ....................................................................................................................................................... P. 43
I Software Update .............................................................................................................................................. P. 43
P. 42
Information
I Information .......................................................................................................................................................
P. 44
26
Picture Adjust
Picture Mode
You can adjust the image quality according to the type of video image you are viewing.
SettingDescription
NaturalImage quality that focuses on natural color and gradation reproduction. Suitable
DynamicThis is the picture setting best suited for viewing the picture in a room that cannot
User 1 to User 6Enables user-defined image quality data to be saved and retrieved.
You can configure the following setting items by pressing the [MENU] button to display the menu, followed by selecting
“Picture Adjust” " “Picture Mode” and pressing the [OK] button.
Sharpness
The sharpness of the image can be adjusted.
0
Setting: 0 (low sharpness) to 50 (high sharpness)
DLC
Expands the dynamic range by controlling the LD current based on information superimposed on the image data.
SettingDescription
OffTurns off the DLC function. LD current is the value configured in “LD Current” or
OnTurns on the DLC function.
for displaying video images in general.
be made completely dark.
the current value controlled by “Auto Intensity”.
Adjust/Set
Auto Intensity
Controls the LD current value to maintain the projector brightness at a constant level.
SettingDescription
OffLight intensity is manually set.
OnLight intensity will be constant.
* This item cannot be set when “DLC” is set to “On”.
LD Current
Controls the brightness of the light source by controlling the LD current.
0
Setting range: 38 to 100
* This function is disabled when “Auto Intensity” is set to “On” or when “DLC” is set to “On”.
Aperture
For changing the brightness through controlling the aperture.
0
Setting range: -7 (stops down) to 0 (opens up)
27
User Name Edit
0
0
0
0
HIDE
A
B
MagentaBlue
Cyan
GreenYellow
Red
Clockwise rotation: -
Counterclockwise rotation: +
Axis Position (Image)
Adjustable range when
Red is selected: ± 30°
with Red as the center
Red
On
Before
Brightness
Saturation
Hue
Axis Position
Color Selection
Color Management
Reset
Color Management
You can edit the “User 1” to “User 6” names in the Picture mode.
0
Characters that are usable include alphabets (upper or lower case), numeric characters, and symbols.
0
Enter not more than 10 characters.
Color Management
Each of the colors is adjustable according to the user’s preference.
Select the “Picture Adjust” " “Color
1
Set “Color Management” to “On”, and press the [OK] button
2
Adjust to the preferred color
3
A
Select “Color Selection”, and press the H I
select the color to adjust
0
For color adjustment, select the color from the
following:
“Magenta”.
B
Adjust the selected color
Item
Axis Position -30 to 30Fine-tune the position
Adjust/Set
Hue-30 to 30Adjusts the hue (color
Saturation-30 to 30Adjusts the color
Brightness-30 to 30Adjusts the
0
Selecting “Reset” resets all the adjustment data.
0
Pressing the [HIDE] button on the remote control
enables you to check the image before
adjustment. Press the [HIDE] button again to
return to the adjustment screen.
Press the [MENU] button to exit
4
Management” menu, and press the [OK] button.
keys to
“Red”, “Yellow”, “Green”, “Cyan”, “Blue”,
Setting Range
Description
of the central axis of
the selected color.
tone).
saturation (vividness).
-30 (dull) to +30 (vivid)
brightness.
-30 (dark) to +30
(bright)
28
Color Temp.
For setting the color temperature of the video image.
0
The selectable “Color Temp.” settings vary according to “Picture Mode”.
“Color Temp.”
Color Temp.Description
5500KIncreasing the value enhances the blue tone of the video image, while decreasing
6500K
9500K
High BrightColor temperature that gives priority to brightness.
Custom 1 to Custom 2The color temperature of video images can be adjusted manually and saved as
the value enhances the red tone.
one of the three customized settings.
List of selectable “Color Temp.” according to “Picture Mode”
Picture ModeColor Temp.
Natural
User 1 to User 6
DynamicHigh Bright
5500K
6500K
9500K
High Bright
Custom 1 to Custom 2
Correction Value
For setting the base color temperature for the adjustment of “Gain Red” / “Gain Green” / “Gain Blue” / “Offset Red” /
“Offset Green” / “Offset Blue” when one of the “Custom 1” to “Custom 3” setting is selected in “Color Temp.”.
Gain Red / Gain Green / Gain Blue
Adjusts each color in the bright parts of the video image.
0
Setting range: -255 (reduces the red/green/blue tone) to 0 (no adjustment)
Offset Red / Offset Green / Offset Blue
Adjusts each color in the dark areas of the video image.
0
0
0
range: -50 (reduces the red/green/blue tone) to 0 (no adjustment) to +50 (enhances the red/green/blue tone)
Setting
Setting “Color Temp.” to “Custom 1”, “Custom 2” or “HDR” allows you to select and adjust a base correction value
(initial value) for adjustment.
The selectable correction values vary according to “Picture Mode”. (Refer to the table below.)
List of selectable “Correction Value” according to “Picture Mode”
Picture ModeCorrection Value
Natural
User 1 to User 6
DynamicNot selectable
5500K
6500K
9500K
High Bright
Adjust/Set
29
Gamma
You can adjust the output value of the projected image with respect to the video signal input.
“Gamma”
GammaDescription
2.2The gamma is set to “2.2”.
Custom 1 to Custom 3Enables fine adjustment of gamma according to preference.
You can perform fine adjustments based on the selected gamma adjustment setting.
Adjustment item and its setting
ItemDescriptionSetting
Color SelectionFor selecting the color for adjusting “Picture Tone”,
White / Red / Green / Blue
“Dark Level” and “Bright Level”.
Picture ToneAdjusts the overall brightness automatically for a
well-balanced result without compromising the
gradation of the image.
Dark LevelAdjusts the dark areas of the input image.
0
To do so, use the H I keys to move the cursor.
Bright LevelAdjusts the bright areas of the input image.
0
To do so, use the H I keys to move the cursor.
-16 (darkens image for an underexposed
effect) to +16 (brightens image for an
overexposed effect)
-7 (darkens the shadows) to +7
(brightens the shadows)
-7 (darkens the highlights) to +7
(brightens the highlights)
Selecting the Base Correction Value (Initial Value) for Adjustment
0
Selecting one of the “Custom 1” to “Custom 3” settings in “Gamma” allows you to select the “Correction Value”.
0
Adjust/Set
Select the base “Correction Value” for adjustment using the H I keys.
When “Correction Value” is set to “Import”
0
selecting “Import” for “Correction Value”, the gamma data created externally can be selected as the base setting
By
value for adjustment.
0
The factory setting for “Import” is “2.2”.
0
can use the calibration software to customize the gamma data adjustment, and import the created gamma data.
You
Please check with your authorized dealer for details.
30
Blur Reduction
For reducing the after-image, which occurs in a fast-moving scene.
Clear Motion Drive
Optimal interpolation according to the content is made possible with the new high-definition image interpolation
technique.
0
Pressing the [C.M.D.] button each time switches the mode in the following sequence: “Off” " “Mode 1” " “Mode
2” " “Mode 3”"“Off”...
* C.M.D. is the abbreviation for Clear Motion Drive.
SettingDescription
OffDoubles the frame rate of the input image by drawing the original image twice.
Mode 1Displays the image as it is at the frame rate of the input image.
Mode 2Displays the image as it is at the frame rate of the input image.
Mode 3Reduce blurriness in the video image by applying black insertion to the Off mode.
Applies black insertion to reduce blurriness in the video images.
Motion Enhance
You can reduce motion blur with this function enhancing the response of D-ILA image devices.
If the image outline is unnatural, set this item to “Off”.
SettingDescription
OffDoes not perform correction.
OnReduces image blurring.
GainWhen Motion Enhance is set to “On”, the overall intensity is adjusted using Gain,
Red
Green
Blue
while adjustment of each color is performed using Red/Green/Blue.
Adjust/Set
Contrast
For adjusting the white level point to avoid clipping or over saturation.
0
Setting range: -50 (little difference in brightness) to +50 (large difference in brightness)
Brightness
For adjusting the black level point to avoid clipping or over saturation.
0
Setting range: -50 (darker) to +50 (brighter)
Color
For adjusting the color density of the video image.
0
Setting range: -50 (lighter) to +50 (deeper)
Tint
For adjusting the hue of the video image.
0
Setting range: -50 (reddish) to +50 (greenish)
31
Input Signal
Input Level
For setting the dynamic range (gradation) of the video input.
0
If the dynamic range is not appropriate, the bright areas become overexposed, and the dark areas become
underexposed.
SettingDescription
16-235 (Video)Select this setting if you are inputting video signals (dynamic range: 16 - 235).
0-255 (PC)Select this setting if you are inputting PC signals (dynamic range: 0 - 255).
Color Space
For setting the color space of the input signal.
SettingDescription
YCbCr444Select this setting when inputting YCbCr (4:4:4) video signals.
YCbCr422Select this setting when inputting YCbCr (4:2:2) video signals.
RGBSelect this setting when inputting RGB video signals.
Channel Hide
Adjust/Set
A function for configuring whether to display video images for each DisplayPort input terminal.
DP 1
DP 2
DP 3
DP 4
SettingDescription
OffDisplays video images with the Hide function disabled.
OnEnables the Hide function and does not display video images.
32
Installation
Zoom (Screen Size)
Ad
j
ustment
ABCD
ABCD
ABCD
Focus Adjustment
Lens Control
Focus / Zoom
For adjusting the lens according to the projection position
Press the [LENS CONTROL] button, and use the [JK]
1
keys to adjust Focus (focus)
and Zoom (screen size)
0
Pressing the [LENS CONTROL] or [OK] button each time switches the mode in the following sequence:
“Focus” " “Zoom” " “Focus”...
.
2
Press the [MENU] button once, or the [BACK] twice, to end adjustment
Image Pattern
For setting whether to display the lens adjustment pattern.
SettingDescription
OnDisplays the lens adjustment pattern.
OffDisplays external signals, and does not display the lens adjustment pattern.
Adjust/Set
33
Pixel Adjust
For correcting the phase shifting between each RGB color by adjusting the pixel.
Adjust
For setting the adjustment feature to On or Off.
Adjust Area
SettingDescription
WholeAdjusts the entire image.
ZoneEnables fine adjustment of each area by dividing the screen evenly into 10 vertical
and horizontal zones.
Adjust Color
For selecting the color to adjust (“Red” or “Blue”).
Adjust Pattern
SettingDescription
OnDisplays the test pattern for adjustment.
OffDisplays the external signals without displaying the test pattern for adjustment.
Adjust Pattern Color
For setting the color of the adjustment pattern displayed during adjustment to “White” or “Yellow / Cyan”.
Adjust (Pixel)
Adjust/Set
When “Adjust Area” is set to “Whole”, adjustment can be made by moving in units of one pixel on the screen of the color
selected in “Adjust Color”.
Æ “Whole Adjust (Pixel) Operation Procedure” (P.
0
Adjustment cannot be made when “Adjust Area” is set to “Zone”.
SettingDescription
H (Horizontal)Setting range: -2 (moves red/blue to the left) to +2 (moves red/blue to the right)
V (Vertical)Setting range: -2 (moves red/blue downward) to +2 (moves red/blue upward)
35)
Adjust (Fine)
When “Adjust Area” is set to “Whole”, adjustment can be made by moving in units of 1/8 pixel on the screen of the color
selected in “Adjust Color”.
When “Adjust Area” is set to “Zone”, the screen is divided evenly into 10 vertical and horizontal zones, and fine
adjustment of each area is possible.
Æ “Zone Adjust Operation Procedure” (P. 37)
SettingDescription
H (Horizontal)Setting range: -31 (moves red/blue to the left) to +31 (moves red/blue to the right)
V (Vertical)Setting range: -31 (moves red/blue downward) to +31 (moves red/blue upward)
Reset
Restores all pixel adjustment data to the factory default.
34
Whole Adjust (Pixel) Operation Procedure
Color A.
BACK
GAMMA
Adjust. Color P. A. Area
COLOR
TEMP
LENS
AP.
PIC.
ADJ.
H 0
V 0
Red
Pixel Adjust
Back
Whole Adjust (Pixel)
V (Vertical)
H (Horizontal)
Adjustment (Pixel) Window
Adjustment Pattern
Color A.
BACK
GAMMA
Adjust. Color P. A. Area
COLOR
TEMP
LENS
AP.
PIC.
ADJ.
H 0
V 0
Red
Pixel Adjust
Back
Whole Adjust (Pixel)
Remote Control Operation
Guide
Color for
Adjustment
Pixel Adjustment Setting
For making general adjustments to slight color fringing in the horizontal/vertical directions of the video image.
A
Set “Adjust Area” to “Whole”
B
Select “Adjust Color” and “Adjust Pattern Color”
C
Select “Adjust (Pixel)”, and press the [OK] button
0
The Adjustment mode is activated, and the selected adjustment pattern and Adjustment (Pixel) window are
displayed.
.
D
Use the [JKH I] keys to move and adjust the vertical and horizontal pixels of the entire zone
0
The adjustment setting appears at the center of the Adjustment (Pixel) window.
Adjust/Set
.
E
After adjustment is complete, press the [BACK] button twice to exit the Adjustment mode
Remote Control Operation Guide
Button NameFunctionDescription of Operation
[GAMMA]Color A.Changes “Adjust Color”.
[COLOR TEMP.]AdjustSwitches between “Adjust (Pixel)” and “Adjust (Fine)”.
0
Switches to “Adjust (Pixel)” when “Adjust Area” is set to “Zone”.
[LENS AP.]Color P.Changes “Adjust Pattern Color”.
[PIC ADJ.]A. AreaSwitches “Adjust Area”.
0
A zone cursor appears on the adjustment pattern when the “Zone”
setting is selected.
35
Whole Adjust (Fine) Operation Procedure
0 ( 0 / 0 )
0 ( 0 / 0 )
V
H
Red
Whole Adjust (Fine)
Pixel Adjust
Color A.
BACK
GAMMA
Adjust. Color P. A. Area
COLOR
TEMP
LENS
AP.
PIC.
ADJ.
Back
V (Vertical)
H (Horizontal)
Fine Window
Adjustment Pattern
H -20 ( -20 / -20)
V 5 ( 5 / 5)
0 ( 0 / 0 )
0 ( 0 / 0 )
V
H
Red
Whole Adjust (Fine)
Pixel Adjust
Color A.
BACK
GAMMA
Adjust. Color P. A. Area
COLOR
TEMP
LENS
AP.
PIC.
ADJ.
Back
Indicates the maximum and
minimum misalignment value of
the entire screen.(Max. / Min.)
Adjustment Setting
Remote Control Operation
Guide
Color for
Adjustment
Pixel Adjustment Setting
For making general adjustments on the misalignment of the entire screen using “Adjust (Pixel)”, followed by making
fine adjustments.
A
Set “Adjust Area” to “Whole”
B
Select “Adjust Color” and “Adjust Pattern Color”
C
Select Adjust (Fine), and press the [OK] button
0
The Adjustment mode is activated, and the selected adjustment pattern and Fine window are displayed.
0
The adjustable range may be smaller depending on the pixels being adjusted on the entire screen.
.
D
Use the [JKH I] keys to move and adjust the vertical and horizontal pixels of the entire zone
Adjust/Set
0
The adjustment setting appears at the center of the Fine window.
.
E
After adjustment is complete, press the [BACK] button twice to exit the Adjustment mode
MEMO
0
If both the maximum overall screen misalignment of H (horizontal direction) and V (vertical direction) are “31”, you
cannot select a value that is larger than the displayed setting even when the adjustment setting is lower than the
maximum value.
0
If the minimum overall screen misalignment is “-31”, you cannot select a value that is smaller than the displayed
setting even when the adjustment setting is higher than the minimum value.
36
Zone Adjust Operation Procedure
V (Vertical)
H (Horizontal)
Zone Adjustment Window
Zone Cursor
Adjustment Pattern
Red
Color A.
BACK
GAMMA
Adjust. Color P. A. Area
COLOR
TEMP
LENS
AP.
PIC.
ADJ.
Back
0
0 / 0
0V
H
Position
Zone Adjust
Pixel Adjust
Adjustment Setting
Cursor Position
Remote Control Operation
Guide
Color for
Adjustment
Pixel Adjustment Setting
Red
Color A.
BACK
GAMMA
Adjust. Color P. A. Area
COLOR
TEMP
LENS
AP.
PIC.
ADJ.
Back
-31
7HV
0
0 / 0
8 / 5
0V
H
Position
Zone Adjust
Pixel Adjust
Position
For fine-tuning misalignments on a part of the screen after adjusting the overall screen misalignment using “Adjust
(Pixel)” and “Adjust (Fine)”.
0
The screen can be divided vertically and horizontally into 10 sections for partial adjustments to be made.
A
Set “Adjust Area” to “Zone”
B
Select “Adjust Color” and “Adjust Pattern Color”
C
Select Adjust (Fine), and press the [OK] button
0
Adjustment mode is activated, and the selected adjustment pattern and Zone Adjustment window are displayed.
The
0
The adjustable range may be smaller depending on the pixels being adjusted on the entire screen.
.
D
Press the [JKH I] keys to move the cursor to the point to be adjusted
E
Press the [OK] button to enter the Adjustment mode
F
Use the [JKH I] keys to move and adjust the vertical and horizontal pixels of the entire zone
0
The adjustment setting appears at the center of the Zone Adjustment window.
Adjust/Set
.
G
After adjustment is complete, press the [BACK] button twice to exit the Adjustment mode
37
Mask
Mask: black strip around the
p
eripher
y
On
Off
For hiding the peripheral area of the image with a mask (black strip).
SettingDescription
OffNot masked.
OnHides the ranges specified in “Top”, “Bottom”, “Left” and “Right” by masking (with
black strips).
.
“Top” / “Bottom” / “Left” / “Right”
For specifying the ranges to hide by masking (with black strips).
0
Setting range: 0 to 220
Distortion Correction
Corrects distortion of the screen.
Adjust/Set
Distortion Correction
For setting the adjustment feature to On or Off.
Adjust Pattern Color
For setting the color of the adjustment pattern displayed during adjustment to “White” or “Green”.
Adjust Pattern
SettingDescription
OnDisplays the test pattern for adjustment.
OffDisplays the external signals without displaying the test pattern for adjustment.
Adjust
Displays the adjustment screen.
38
Operation procedure for Adjust
BACK
Back
0
0 / 0
0V
H
Position
Distortion Correction
BACK
Back
0
0 / 0
0V
H
Position
Distortion Correction
A
Select “Adjust Pattern Color”
B
Select “Adjust”, and press the [OK] button
0
The Adjustment mode is activated, and the selected adjustment pattern and Adjustment window are displayed.
.
C
Select the position to compensate by using the [JKH I] keys to move the cursor, followed by pressing the [OK]
button.
D
Use the [JKH I] keys to set the compensation value
0
Pressing the [OK] button each time switches the setting item in sequence.
“Position” " “H” "“V” " “Position”...
0
The item that is currently being set is displayed in blue.
0
A red cursor is displayed when setting the position.
A blue cursor is displayed when setting the compensation value.
Adjust/Set
.
E
After adjustment is complete, press the [BACK] button to exit the Adjustment mode
MEMO
0
Noise may occur during adjustment. This is not a malfunction.
39
Edge Blending
Corrects the seam between the images during projection by multiple projectors.
This function is disabled when “Picture Mode” is set to “Dynamic”.
*
Edge Blending
For setting the function to On or Off.
SettingDescription
OffDisables the Edge Blending function.
OnEnables the Edge Blending function.
Guide
For setting the guideline display (start point: green; end point: red).
SettingDescription
OffHides the guideline.
OnDisplays the guideline.
Position Select
For setting the compensation position.
SettingDescription
TopFor setting the start and end points using the Start/End item.
Bottom
Adjust/Set
Left
Right
Start/End
For setting the start and end points of the compensation position selected in “Position Select”.
0
Setting range: 0 to 255 (left/right), 0 to 135 (up/down)
Black Level
For adjusting the black level.
0
Setting range: 0 to 50
Installation Style
For setting to “Front”, “Ceiling Mount (F)”, “Rear”, or “Ceiling Mount (R)” according to the installation status of the
projector.
0
“Front” or “Ceiling Mount (F)” is set when projector is installed in the front with respect to the screen.
0
“Rear” or “Ceiling Mount (R)” is set when projector is installed in the rear with respect to the screen.
40
LED Indication
When LED Indication is set to “Off”, the LED indicator does not light up or blink under the following status.
0
When the time to replace the laser light source is near. (
0
When HIDE is on. (P.
0
When the projector receives a signal from a remote control which is set to a different code mode (A or B). (
62)
P. 44)
P. 43)
High Altitude Mode
For setting the high altitude mode to “On” or “Off”.
Set to “On” when using the projector at a location of low atmospheric pressure (higher than 900 m above sea level).
Display Setup
Back Color
For setting the color of the background to “Blue” or “Black” when there is no signal input.
Menu Position
For setting the display position of the menu.
Signal Display
For setting the display of the input information to “On” or “Off”.
SettingDescription
OnShows the input terminal for 5 seconds when input is switched.
OffNot displayed.
Adjust/Set
Logo
For setting the display of logo during startup to “On” or “Off”.
SettingDescription
OnDisplays the “D-ILA” logo for 5 seconds during startup.
OffNot displayed.
41
Function
Off Timer
For setting the duration before the power turns off automatically when the projector is not operated.
* The setting will be retained even after the Off Timer operation has completed.
Network
For specifying the settings for external control from a PC or smartphone.
SettingSettingDescription
DHCP ClientOnObtains the IP address automatically from the DHCP server inside the connected
network.
OffFor configuring the network settings manually.
IP AddressFor configuring the IP address.
Subnet MaskFor configuring the subnet mask.
Default GatewayFor configuring the default gateway.
MAC AddressDisplays the MAC address of the unit.
SetApplies the network settings.
Adjust/Set
Glossary of Network Terminology
DHCP
IP Address: Numeric characters for identifying the device that is connected to the network.
Subnet Mask: Numeric characters that define the bit count used for the network address that is a
Default Gateway: Server for communicating beyond the network that is divided by the subnet mask.
MAC Address: Abbreviation for Media Access Control address. This is a number that is unique to each
: Abbreviation for Dynamic Host Configuration Protocol. This is a protocol for the network
to assign an IP address automatically to the connected device.
segment of the IP address.
network adapter. Each of the network adapters is assigned with a unique MAC address.
42
Remote Code
LIGHT
STANDBY/ON
WARNING
(Green)
For changing the remote control code.
SettingDescription
AChange the remote control code from “B” to “A”.
BChange the remote control code from “A” to “B”.
0
You need to configure the remote control according to the settings of this unit.
On the remote control unit, press the [MENU] and [BACK] buttons at the same time for three seconds or longer to
switch the code.
0
The backlight of the remote control blinks 3 times: change the remote control code to “A”
0
The backlight of the remote control blinks 2 times: change the remote control code to “B”
0
If the setting differs between this unit and the remote control, the “STANDBY/ON” indicator blinks in green when
receiving the remote control code.
.
Hide Mode
For reducing the power consumption through suppressing the current supply for the LD block when the [HIDE] button
is pressed to hide the image temporarily.
SettingDescription
OffDo not suppress the current supply when the [HIDE] button is pressed to hide the
image temporarily.
OnSuppresses the current supply when the [HIDE] button is pressed to hide the image
temporarily.
Software Update
For performing a software update.
For the latest information on the software, refer to http://www3.jvckenwood.com/english/download/.
Adjust/Set
43
Information
Page 1
SettingDescription
InputDisplays video input terminal.
StatusDisplays the image output status.
Resolution
(DP 1 / DP 2 / DP 3 / DP 4)
Light Source TimeDisplays the laser light source time.
Soft Ver.Displays the firmware version.
Pages 2 to 5
SettingDescription
DP 1 to DP 4Displays the terminal for which the corresponding information is displayed.
Resolution
H Frequency
V Frequency
Color DepthDisplays the color bit depth of the input video signal.
Color SpaceDisplays the Color Space detected by AVI Info frame.
Adjust/Set
Link RateDisplays the transmission frequency of the input signal.
Lane CountDisplays the number of lanes used for the input signal.
Displays the resolution information of signal input to each of the DP 1 to DP 4
terminals.
Displays the image resolution.
Displays the horizontal frequency.
Displays the vertical frequency.
0
Not displayed when YCbCr (4:2:2) is input.
0
Displayed when Deep Color information is received from the source device.
44
Maintaining the Cabinet and Remote Control
2 3 4
1
Sponge Filter (Gray)
Air Filter
(White)
0
Gently wipe off dirt on the cabinet with a soft cloth.
0
If it is extremely dirty, wet a cloth in water, wring dry and use it to wipe off the dirt, followed by wiping again with a
dry cloth.
0
Pay attention to the following as the cabinet may deteriorate in condition or the paint may come off.
0
Do not wipe with thinner or benzine
0
Do not allow prolonged contact with rubber or plastic products
0
Do not spray volatile chemicals such as insecticide
Cleaning and Replacing the Filter
the filter regularly. Using a filter without cleaning may reduce the brightness of the image. Dirt that enters the unit
Clean
may also appear as shadows on the image.
.
Loosen the 4 screws and remove the cover
1
0
The screws cannot be removed from the cover. Do not try to remove the screws from the cover by force.
Remove the sponge filter
2
Use a vacuum cleaner to remove dirt from the sponge filter carefully
3
Restore the sponge filter
4
Restore the cover and fasten the 4 screws
5
Maintenance
45
CAUTION
0
Do not wash the air filter with water. Doing so may cause the filter to deteriorate.
0
Make sure to attach the air filter and sponge filter in the correct sequence.
MEMO
0
If you need to replace the air filter or sponge filter because they are broken or if there is dirt inside the unit, please
consult our dealer or any nearby service center.
0
Air filter
Product no.: F1K-0062-00
0
Sponge filter
Product no.: J3K-0049-00
About the Lens
0
This projector does not come with a projection lens.
To use the projector, please mount a projection lens according to your requirements.
0
The use of a separate spacer may be required depending on the specifications of the lens.
0
Please connect the connector before a projection lens attached.
Maintenance
46
Troubleshooting
Before sending the unit to your authorized dealer for repair, please check the following points.
The following symptoms are not malfunctions.
You do not need to worry about the following symptoms if there is no abnormality on the screen.
0
A part of the top or front surface of the unit is hot.
0
A creaking sound is heard from the unit.
0
An operating sound is heard from the inside of the unit.
0
Color smear occurs on some screens.
This unit is a digital device. This unit may become unable to operate normally due to external static or noise.
Perform the following operations when such malfunctions occur.
A
If the unit is in the Standby mode, pull out the power plug, followed by inserting it again
B
Press the A button on the projector unit to turn on the power again
Power is not supplied
CheckActionRefer to
Is the power cord disconnected?Insert the power cord (plug) firmly.P. 22
Is the unit in the Cool-down mode?After exiting the Cool-down mode, turn on the power again. P. 24
Power shuts down automatically
CheckActionRefer to
Has “Off Timer” been configured?Set “Off Timer” to “Off”.P. 42
Are the air inlets and exhaust vent
blocked?
Is there a large amount of dirt attached to
the sponge filter?
Leave proper clearance when installing the unit.P. 12, 17
Remove the dirt using a vacuum cleaner.P. 45
Video image does not appear
CheckActionRefer to
Is the correct external input selected?Select the correct external input terminal.P. 23
Is the power of the AV device or PC
turned on?
Is the AV device or PC properly
connected?
Are the correct signals being output from
the AV device or PC?
Is an intermediate device (AV amplifier,
divider, etc.) in use?
Turn on the power of the AV device or PC and play the
video.
Connect the AV device or PC properly.P. 21
Set the AV device or PC properly.P. 21
Change the sequence of turning on the source device,
intermediate
each device, ensure that the signal output is stable before
turning on the next device.
device and the projector. And after turning on
P. 21
P. 21
Troubleshooting
47
Video image looks unnatural
Colors are unnatural
CheckActionRefer to
Is the color space of the input signal
correctly set?
Is the image correctly adjusted?Adjust “Color” and “Tint” accordingly.P. 31
Is the AV device or PC properly
connected?
* The video image may appear slightly reddish immediately after starting up. This is not a malfunction.
The color may turn out unnatural when the input signal is
different from that in the projector setting.
Set the “Color Space” for “Input Signal” correctly.
Connect the AV device or PC properly.P. 21
P. 32
Video image is fuzzy
CheckActionRefer to
Is the focus correctly adjusted?Adjust the focus.P. 33
Is the unit placed too near or too far away
from the screen?
Set the unit at a correct distance from the screen.P. 55
Projected image is dark
CheckActionRefer to
Is the laser light source near exhaustion? Check the laser light source time in the “Information” menu.
Is the aperture closed?Increase the value of the “Aperture” setting.P. 27
Is the value of the “LD Current” setting
small?
40,000 hours have elapsed, the brightness will be half the
If
brightness at shipment.
Increase the value of the “LD Current” setting.P. 27
P. 44
Striped patterns appear on the screen
CheckActionRefer to
Does the fabric of the screen have a
regular pattern?
Interference fringes may sometimes occur between the
fabric
pattern and the pixels. Please consult the authorized
dealer.
Video images are missing
CheckActionRefer to
Has screen mask been configured?Set “Mask” to “Off”.P. 38
Troubleshooting
—
48
Zoom or focus does not work
DP 1
CheckActionRefer to
Is the lens replaced?Depending on the lens position, the lens may not work
when it has been replaced.
While at the Focus / Zoom adjustment screen, press and
hold the J
allow the lens to recover from this condition.
or K key for 2 seconds or longer. Doing so will
P. 33
Remote control does not work
CheckActionRefer to
Are the batteries correctly loaded?Match the polarities (t s) correctly when loading the
batteries.
Are the batteries exhausted?Replace with new batteries.P. 15
Is there an obstructing object between
the remote control and remote sensor?
Is the remote control held too far away
from the unit?
Remove any obstructing object.P. 15
Hold the remote control closer to the sensor during use.P. 15
P. 15
Noise is heard
CheckActionRefer to
Is the exhaust vent blocked?
Is the unit used near a heater or airconditioner?
Check the installation condition of the projector.
When
the surrounding temperature of the projector is high,
the fan revolution speed increases to protect the projector
unit, hence a louder operating sound.
P. 17
There are small black or colored dots on the screen
The D-ILA device is manufactured using high-precision technologies, but there may be some (less than 0.01%) missing
pixels or pixels that remain permanently lit. This is not a malfunction.
When the Following Messages Appear...
MessageDescriptionAction
A video signal that cannot be used with
.
this unit has been input (the names of
input terminals such as “DP 1” will be
displayed in yellow).
Input video signals that can be used.
(P.
57)
Troubleshooting
49
External Control
15
69
This Unit
D6 D7D4 D5D2 D3D0 D1
Stop bitStart bit
Projector Control
Connection Authentication Procedure
PJA CK
PJ RE Q
PJ _O K
Within 5 Seconds
Controlling PC
3-way Handshake
TCP Port No. 20554
Establishment of TCP Connection
Projector
It is possible to control this unit by connecting it to a PC using an RS-232C cross cable (D-sub 9-pin).
The projector can be controlled by connecting it to a PC through the computer network with a LAN cable for control
commands to be sent to the projector.
Æ “ Network ” (P.
0
Please use it after you have gained proper understanding from professional books or consulting the system
administrator.
RS-232C Specifications
0
PC refers to the controller, such as a personal computer.
42)
Pin No.SignalFunctionSignal Direction
2RxDReceive dataPC "
3TxDTransmission dataThis unit " PC
5GNDSignal ground
1, 4, 6 - 9N/C
ModeNon-synchronous
Character length8 bit
ParityNone
Start bit1
Stop bit1
Data rate19200 bps
Data formatBinary
——
—
This unit
TCP/IP Connection
Before controlling via LAN, it is necessary to establish connection of the TCP layer by a “3-way handshake”, followed
sending out “PJREQ” and receiving “PJACK” within five seconds after the projector sends out “PJ_OK” for connection
by
authentication.
If you are unable to complete sending within five seconds, or when “PJ_NG” or “PJNAK” is received, check the operating
status of the projector, followed by performing the steps again starting from establishment of a TCP connection.
Others
50
.
Command Format
The command between this unit and the computer consists of “Header”, “Unit ID”, “Command”, “Data” and “End”.
0
Header (1 byte), Unit ID (2 bytes), Command (2 bytes), Data (n bytes), End (1 byte)
Header
This binary code indicates the start of communication.
Binary CodeTypeDescription
21Operating commandPC "
3FReference command PC "
40Response command This unit " PC
06ACKThis unit " PC (returns to PC after the command is accepted without
Unit ID
This is a code that specifies the unit. The binary code is fixed at “8901”.
Command and data
This unit
This unit
error)
Operating command and data (binary code)
Command
0000
5057Power
4950InputWhen power is on
5243Remote
TypeDescription
Connection
check
supply
control
Check whether communication is
enabled between this unit and the
PC during standby.
During standby
31: Turns on the power
When power is on
30: Turns off the power (Standby
mode)
38: DP 1
39: DP 2
41: DP 3
42: DP 4
Sends the same code as the
supplied remote control.
0
“Remote Control
Code”P.
52
Reference command and data (binary code)
Command
5057Power
4950InputWhen power is on
TypeDescription
supply
End
This code indicates the end of communication. The binary code is fixed at “0A”.
During standby or when power is
on
30: Standby mode
31: When power is on
32: In the Cool-down mode
When error occurs on this unit
34:
38: DP 1
39: DP 2
41: DP 3
42: DP 4
51
Others
Remote Control Code
Binary code is sent during communication.
0
following applies to the case when the remote control code is “A”. In the case of “B”, add “36” to the beginning
The
of the code.
Remote Control Button NameBinary Code
STAND BY37 33 30 36
ON37 33 30 35
INPUT 137 33 37 30
INPUT 237 33 37 31
DUAL37 33 34 44
INPUT 337 33 34 42
INPUT 437 33 34 43
QUAD37 33 34 36
LENS CONTROL37 33 33 30
C.M.D.37 33 38 41
MOTION ENHANCE37 33 46 36
HIDE37 33 31 44
J
K
I
H
37 33 30 31
37 33 30 32
37 33 33 34
37 33 33 36
Remote Control Button NameBinary Code
OK37 33 32 46
MENU37 33 32 45
BACK37 33 30 33
NATURAL37 33 36 41
DYNAMIC37 33 36 42
NAME EDIT37 33 46 37
USER137 33 36 43
USER237 33 36 44
USER337 33 36 45
USER437 33 43 41
USER537 33 43 42
USER637 33 43 43
GAMMA37 33 37 35
COLOR TEMP.37 33 37 36
LENS AP.37 33 32 30
PIC. ADJ.37 33 37 32
Others
52
Communications Example
This section shows the communication examples of RS-232C.
Operating command
TypeCommandDescription
Connection checkPC "
Power (On)PC "
Power (Off)PC "
Remote control
(MENU)
Reference command
TypeCommandDescription
Power (On)PC "
Input (DP 1)PC " This unit: 3F 89 01 49 50 0A
This unit: 21 89 01 00 00 0A
This unit " PC: 06 89 01 00 00 0A
This unit: 21 89 01 50 57 31 0A
This unit " PC: 06 89 01 50 57 0A
This unit: 21 89 01 50 57 30 0A
This unit " PC: 06 89 01 50 57 0A
This unit: 21 89 01 52 43 37 33 32 45 0A
PC "
This unit " PC: 06 89 01 52 43 0A
This unit: 3F 89 01 50 57 0A
This unit " PC: 06 89 01 50 57 0A
This unit " PC: 40 89 01 50 57 31 0A
This unit " PC: 06 89 01 49 50 0A
This unit " PC: 40 89 01 49 50 38 0A
Connection check
When power is turned on from the
Standby mode
When power is turned off (Standby
mode) from power-on mode
When the same operation as
pressing the [MENU] button on the
remote control is performed
When information on the power-on
state is acquired
When information on DP 1 input is
acquired
53
Others
Specifications
Product NameD-ILA Projector
Model NameDLA-VS4500
Display Panel/SizeD-ILA device *1, 2
0.69” 4K D-ILA (4096 x 2160 pixels) x 3
Light SourceBlu-Escent Laser / Phosphor
Screen SizeApprox. 60” to 300” (Aspect ratio of 4096 x 2160)
Brightness3000 lm
Projection DistanceRefer to P. 55.
Input Compatibility SignalRefer to P. 57.
Display Resolution4096 x 2160 pixels
Input TerminalDisplayPort InputDisplayPort 1.2a, 20-pin (male) x 4
Output Terminal SYNC OUTMini jack, TTL output x 1 *3
Control Terminal RS-232C TerminalSingle, D-sub 9-pin (male) x 1 *4
Remote TerminalStereo mini jack (remote control) x 1
LAN TerminalSingle, RJ-45 plug, 10BASE-T/100BASE-TX x 1
Service
Terminal
Power RequirementsAC 100 V to 240 V, 50 Hz/60 Hz
Power Consumption750 W (during standby: 1.5 W *6)
Operation EnvironmentTemperature: 5°C to 35°C; humidity: 20% to 80%; storage
Installation HeightBelow 6,561 ft (2,000 m)
Dimensions (Width x Height x Depth)500 mm x 235 mm x 719 mm (including feet)
Mass35.5 kg
AccessoriesRefer to P. 10.
*1D-ILA is the abbreviation for Direct Drive Image Light Amplifier.
*2D-ILA
Only 0.01% or less of the pixels are either missing or would remain permanently lit.
*3For synchronizing with other equipment.
*4For external control.
*5Exclusively for firmware update.
*6The power consumption of this product during networked standby when all wired network ports are connected
is 1.5 W.
0
Design and specifications are subject to change without prior notice.
0
Please
to aid comprehension. Images may differ from the actual product.
SERVICESingle (USB Type A) x 1 *5
temperature: -10°C to 60
devices are manufactured using extremely high-precision technology with a pixel effectiveness of 99.99%.
note that some of the pictures and illustrations may have been abridged, enlarged or contextualized in order
°C
Others
54
Screen Size and Projection Distance
GL-MZ4009Z
Projection Distance (m)
Screen Size
Diagonal (Inch)
601.221.741.291.83
701.442.041.522.15
801.652.341.742.47
901.872.651.972.78
1002.082.952.193.10
1102.303.252.423.42
1202.523.552.653.74
1302.733.852.874.05
1402.954.153.104.37
1503.164.463.334.69
1603.384.763.555.00
1703.595.063.785.32
1803.815.364.015.64
1904.025.664.235.95
2004.245.964.466.27
2104.456.264.696.59
2204.676.574.916.90
2304.886.875.147.22
2405.107.175.367.54
2505.327.475.597.85
2605.537.775.828.17
2705.758.076.048.49
2805.968.376.278.81
2906.188.68--
3006.398.98--
17:9 Screen16:9 Screen
Wide-endTele-endWide-endTele-end
55
Others
GL-MZ4014Z
Projection Distance (m)
Screen Size
Diagonal (Inch)
601.663.431.753.61
701.964.022.064.23
802.254.602.374.84
902.545.192.675.46
1002.835.772.986.07
1103.126.363.286.69
1203.416.943.597.30
1303.707.533.907.92
1403.998.114.208.53
1504.288.704.519.15
1604.589.284.819.76
1704.879.875.1210.38
1805.1610.455.4310.99
1905.4511.045.7311.61
2005.7411.626.0412.22
2106.0312.216.3412.84
2206.3212.796.6513.45
2306.6113.386.9514.07
2406.9013.967.2614.68
2507.1914.557.5715.30
2607.4915.137.8715.91
2707.7815.728.1816.53
2808.0716.318.4817.14
2908.3616.89--
3008.6517.48--
17:9 Screen16:9 Screen
Wide-endTele-endWide-endTele-end
Others
56
Types of Possible Input Signals
Single - DP1 - DP4
OriginalInput Signal
Projector
Designation
VGA640 x 480
1080p1920 x 10801920 x 1080 56,25050,000148.502640112519201080
2K2048 x 10802048 x 1080 56,25050,000148.502640112520481080
UXGA1600 x 12001600 x 1200 75,00060,000162.002160125016001200
WUXGA1920 x 12001920 x 1200 74,55659,885193.252592124519201200
QXGA2048 x 15362048 x 1536 95,44659,954267.252800159220481536
WQXGA2560 x 16002560 x 1600 99,45859,987348.503504165825601600
4K3840 x 21603840 x 2160 53,94623,976296.705500225038402160
Resolution
4096 x 21604096 x 2160 53,94623,976296.705500225040962160
Terminal for
Connection
[DP 1] /
[DP 2] /
[DP 3] /
[DP 4]
Resolutionfh [kHz]fv [Hz]
640 x 48031,46959,94025.18800525640480
67,43359,940148.352200112519201080
67,50060,000148.502200112519201080
67,43359,940148.352200112520481080
67,50060,000148.502200112520481080
54,00024,000297.005500225038402160
56,25025,000297.005280225038402160
67,43329,970296.704400225038402160
67,50030,000297.004400225038402160
112,50050,000594.005280225038402160
134,86559,940593.414400225038402160
135,00060,000594.004400225038402160
54,00024,000297.005500225040962160
56,25025,000297.005280225040962160
67,43329,970296.704400225040962160
67,50030,000297.004400225040962160
112,50050,000594.005280225040962160
134,86559,940593.414400225040962160
135,00060,000594.004400225040962160
dot CLK
[MHz]
Total No.
of Dots
[dot]
Total No.
of Lines
[line]
No. of
Effective
Dots [dot]
No. of
Effective
Lines
[line]
57
Others
Dual - stripes
Same for all
frames
[DP 1][DP 3]
H/2H/2
V
H
OriginalInput Signal
Projector
Designation
WQXGA2560 x 1600 [DP 1],
4K3840 x 21601920 x 2160 135,00060,000297.002200225019202160
Resolution
4096 x 21602048 x 2160 112,50050,000297.002640225020482160
Terminal for
Connection
[DP 3]
Resolution fh [kHz]fv [Hz]
1280 x 1600 99,45859,987174.251752165812801600
198,916119,973348.501752165812801600
270,000120,000594.002200225019202160
135,00060,000297.002200225020482160
270,000120,000594.002200225020482160
dot CLK
[MHz]
Total No.
of Dots
[dot]
Total No.
of Lines
[line]
No. of
Effective
Dots [dot]
No. of
Effective
Lines
[line]
.
Others
58
Dual - frame sequential
[DP 1]
V
H
[DP 3]
V
H
[DP 1]
60 Hz
F1F3F5
F1
120 Hz
F2 F3 F4 F5 F6
F2F4F6
[DP 3]
Output
Time direction
Even number
frame display
Odd number
frame display
OriginalInput Signal
Projector
Designation
WQXGA2560 x 1600 [DP 1],
Resolution
Terminal for
Connection
[DP 3]
Resolutionfh [kHz]fv [Hz]
2560 x 1600 99,45859,987348.503504165825601600
dot CLK
[MHz]
Total No.
of Dots
[dot]
Total No.
of Lines
[line]
No. of
Effective
Dots [dot]
No. of
Effective
Lines
[line]
.
Others
59
Quad - stripes
Same for all
frames
[DP 1] [DP 2] [DP 3] [DP 4]
H/4H/4H/4H/4
V
H
Same for all
frames
[DP 1][DP 3]
[DP 3][DP 4]
H/2
V/2
V/2
H/2
V
H
OriginalInput Signal
Projector
Designation
4K3840 x 2160 [DP 1],
.
Resolution
4096 x 21601024 x 2160 135,00060,000148.501100225010242160
Terminal for
Connection
[DP 2],
[DP 3],
[DP 4]
Resolutionfh [kHz]fv [Hz]
960 x 2160 135,00060,000148.50110022509602160
270,000120,000297.00110022509602160
270,000120,000297.001100225010242160
dot CLK
[MHz]
Total No.
of Dots
[dot]
Total No.
of Lines
[line]
No. of
Effective
Dots [dot]
No. of
Effective
Lines
[line]
Quad - cross
OriginalInput Signal
Designation
4K3840 x 2160 [DP 1],
.
Others
Resolution
4096 x 21602048 x 1080 67,50060,000148.502200112520481080
Projector
Terminal for
Connection
[DP 2],
[DP 3],
[DP 4]
Resolutionfh [kHz]fv [Hz]
1920 x 1080 67,50060,000148.502200112519201080
135,000120,000297.002200112519201080
135,000120,000297.002200112520481080
dot CLK
[MHz]
Total No.
of Dots
[dot]
Total No.
of Lines
[line]
No. of
Effective
Dots [dot]
No. of
Effective
Lines
[line]
60
Quad - frame sequential
[DP 1][DP 3]
H/2H/2
V
H
[DP 2][DP 4]
H/2H/2
V
H
[DP 1]
60 Hz
F1 (L)
F1 (R)
F3 (L)
F3 (R)
F5 (L)
F1
120 Hz
F2 F3 F4 F5 F6
F5 (R)
F2 (L)
F2 (R)
F4 (L)
F4 (R)
F6 (L)
F6 (R)
[DP 3]
[DP 2]
[DP 4]
Output
Time direction
Even number
frame display
Odd number
frame display
OriginalInput Signal
Projector
Designation
4K3840 x 2160 [DP 1],
Resolution
Terminal for
Resolutionfh [kHz]fv [Hz]
Connection
1920 x 2160 135,00060,000297.002200225019202160
4096 x 21602048 x 2160 135,00060,000297.002200225020482160
[DP 2],
[DP 3],
[DP 4]
dot CLK
[MHz]
Total No.
of Dots
[dot]
Total No.
of Lines
[line]
No. of
Effective
Dots [dot]
No. of
Effective
Lines
[line]
.
Others
61
Indicator Display on the Main Unit
STANDBY/ON
LIGHT
WARNING
The indicator appears blinking.
The indicator lights up.
LIGHT
STANDBY/ON
WARNINGLIGHT
STANDBY/ON
WARNING
LIGHT
STANDBY/ON
WARNINGLIGHT
STANDBY/ON
WARNING
When the video image is
temporarily hidden (HIDE is on)
In the Cool-down mode
“STANDBY/ON” blinking (red)
When LD block is starting up
“STANDBY/ON” lights up (green)
In standby state
“STANDBY/ON” lights up (red)
“STANDBY/ON” blinking (green)
・
・
Meaning of the lighting figures
.
Operation mode display
Displays using the different colors and solid/blinking light of the indicator on the projector unit.
.
Others
62
Warning display
LIGHT
STANDBY/ON
WARNING
(Red)(*)Mode
Display
LIGHT
STANDBY/ON
WARNING
Blinking
Simultaneously
(Red)
(Orange)
Mode
Display
LIGHT
STANDBY/ON
WARNING
(Red)
(Orange)
Mode
Display
LIGHT
STANDBY/ON
WARNING
(Green)
You can tell the details of a warning from the (repeated) displays of the “WARNING” and “LIGHT” indicators. The
“STANDBY/ON”
refer to ““Operation mode display”P. 62”.)
The Warning mode is activated once the message is displayed. Projection is interrupted, and the cooling fan is turned
on for about 10 seconds.
The power cannot be turned on again while cooling is in progress. Check the following after cooling is complete.
indicator will light up or appear blinking according to the operation mode of the projector unit. (Please
Indicator Status (Solid/Blinking)
.
Blinking
Frequency
DescriptionCheck and Countermeasure
x2Cooling fan stopped abnormally
x3Internal temperature is abnormally
high
x4External temperature is too high
x1Abnormal circuit operation
x2
0
Check that nothing is blocking
the air inlets.
0
Check that the external
temperature is normal.
Countermeasure: Leave the unit
unoperated until it cools down.
that, turn on the power again.
After
x3
x4
.
x1
x3
x4When the safety switch is activated Request for repair at your
.
x3The remote control code differs
between this unit and the remote
control
.
authorized dealer or a nearby
service center.
Set the remote control code for this
unit and the remote control
correctly.(
P. 43)
If the Warning mode is activated again, wait for the cooling fan to stop, followed by pulling out the power plug from the
outlet.
Request for repair at your authorized dealer or a nearby service center.