JVC VS2200G, DLA-VS2500G, DLA-VS2200ZG User Manual

.
Pour utilisation par le client :
Entrerci-dessous le N°de série qui est situé sous le boîtier. Garder cetteinformation comme référence pour le futur.
Instrucción para el cliente :
Introduzca a continuación el nº de serie que aparece en la parte inferior lateral de la caja. Conserve esta información como referencia para uso ulterior.
For Customer use :
Enter below the serial No. which is located on the side of the cabinet. Retain this information for future reference.
DLA-VS2200ZG DLA-VS2200G
Model No.
Serial No.
DLA-VS2200ZG DLA-VS2200G
N° de modèle
N° de série
DLA-VS2200ZG DLA-VS2200G
Modelo Nº
Nº de serie
D-ILA PROJECTOR
DLA-VS2200ZG DLA-VS2200G
ENGLISH
FRANÇAIS
ESPAÑOL/CASTELLANO
Getting Started Set up Operate Adjust/Set Maintenance Troubleshooting Others
INSTRUCTIONS
.
.
LCT2727-001B
LCT2727-001B

Safety Precautions

⹣晼㯡婌♟㒷
IMPORTANT INFORMATION
This product has a High Intensity Dis-charge (HID) lamp that contains mercury. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information, please contact your local authorities or for USA, the Electronic Industries Alliance: http://www.eiae.org.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. In case where the strong electromagnetic waves or magnetism are near the signal cable, the picture will contain noise. In such cases, please keep the cable away from the sources of the disturbance.
MACHINE NOISE INFORMATION (Germany only)
Changes Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator position is equal or less than 20 dB (A) according to ISO 7779.
About the installation place
Do not install the projector in a place that cannot support its weight securely. If the installation place is not sturdy enough, the projector could fall or overturn, possibly causing personal injury.
WARNING:
THIS APPARATUS MUST BE EARTHED.
CAUTION:
For the customers in Taiwan only
To reduce the risk of electric shock, do not remove cover. Refer servicing to qualified service personnel.
This projector is equipped with a 3-blade grounding type plug to satisfy FCC rule. If you are unable to insert the plug into the outlet, contact your electrician.
FCC INFORMATION (U.S.A. only) CAUTION:
Changes or modification not approved by JVC could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Getting Started

.
2
150 mm and above
150 mm and above
300 mm and above
200 mm and above
300 mm and above
PORTABLE CART WARNING (symbol provided by RETAC)
S3126A
Front
-
-
-
-
-
-
-
-
-
-
-
-
-
IMPORTANT SAFEGUARDS
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order not to defeat the safeguards incorporated into this product, observe the following basic rules for its installation, use and service. Please read these Important Safeguards carefully before use.
All the safety and operating instructions should be read before the product is operated. The safety and operating instructions should be retained for future reference. All warnings on the product and in the operating instructions should be adhered to. All operating instructions should be followed. Place the projector near a wall outlet where the plug can be easily unplugged. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Do not use attachments not recommended by the product manufacturer as they may be hazardous. Do not use this product near water. Do not use immediately after moving from a low temperature to high temperature, as this causes condensation, which may result in fire, electric shock, or other hazards. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. The product should be mounted according to the manufacturer’s instructions, and should use a mount recommended by the manufacturer. When the product is used on a cart, care should be taken to avoid quick stops, excessive force, and uneven surfaces which may cause the product and cart to overturn, damaging equipment or causing possible injury to the operator. Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from overheating. These openings must not be blocked or covered. (The openings should never be blocked by placing the product on bed, sofa, rug, or similar surface. It should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s instructions have been adhered to.) To allow better heat dissipation, keep a clearance between this unit and its surrounding as shown below. When this unit is enclosed in a space of dimensions as shown below, use an air-conditioner so that the internal and external temperatures are the same. Overheating can cause damage.
-
-
-
-
-
-
-
-
-
-
-
-
a) b)
c) d)
e)
f)
When the power supply cord or plug is damaged. If liquid has been spilled, or objects have fallen on the product. If the product has been exposed to rain or water. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the Operation Manual, as an improper adjustment of controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. If the product has been dropped or damaged in any way. When the product exhibits a distinct change in performance, this indicates a need for service.
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or with same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. The product should be placed more than one foot away from heat sources such as radiators, heat registers, stoves, and other products (including amplifiers) that produce heat. When connecting other products such as VCR’s, and DVD players, you should turn off the power of this product for protection against electric shock.
Power source indicated on the label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. This product is equipped with a three-wire plug. This plug will fit only into a grounded power outlet. If you are unable to insert the plug into the outlet, contact your electrician to install the proper outlet. Do not defeat the safety purpose of the grounded plug. Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where they exit from the product. For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power line surges. Do not overload wall outlets, extension cords, or convenience receptacles on other equipment as this can result in a risk of fire or electric shock. Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltages and other hazards. Refer all service to qualified service personnel. Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions:
Getting Started
.
3
-
-
-
-
-
-
-
-
-
-
Do not place combustibles behind the cooling fan. For example, cloth, paper, matches, aerosol cans or gas lighters that present special hazards when over heated. Do not look into the projection lens while the illumination lamp is turned on. Exposure of your eyes to the strong light can result in impaired eyesight. Do not look into the inside of this unit through vents (ventilation holes), etc. Do not look at the illumination lamp directly by opening the cabinet while the illumination lamp is turned on. The illumination lamp also contains ultraviolet rays and the light is so powerful that your eyesight can be impaired. Do not drop, hit, or damage the light-source lamp (lamp unit) in any way. It may cause the light-source lamp to break and lead to injuries. Do not use a damaged light source lamp. If the light-source lamp is broken, ask your dealer to repair it. Fragments from a broken light-source lamp may cause injuries. The light-source lamp used in this projector is a high pressure mercury lamp. Be careful when disposing of the light-source lamp. If anything is unclear, please consult your dealer. Do not ceiling-mount the projector to a place which tends to vibrate; otherwise, the attaching fixture of the projector could be broken by the vibration, possibly causing it to fall or overturn, which could lead to personal injury. Use only the accessory cord designed for this product to prevent shock. Once every three years, please perform an internal test. This unit is provided with replacement parts needed to maintain its function (such as cooling fans). Estimated replacement time of parts can vary greatly depending on frequency of use and the respective environment. For replacement, please consult your dealer, or the nearest authorized JVC service center. When fixing the unit to the ceiling, Please note that we do not take any responsibility, even during the warranty period, if the product is damaged due to use of metal fixtures used for fixation to the ceiling other than our own or if the installation environment of said metal fixtures is not appropriate. If the unit is suspended from the ceiling during use, please be careful in regard to the ambient temperature of the unit. If you use a central heating, the temperature close to the ceiling will be higher than normally expected. Video images can burn into the electronic component parts. Please do not display screens with still images of high brightness or high contrast, such as found in video games and computer programs. Over a long period of time it might stick to the picture element. There is no problem with the playback of moving images, e.g. normal video footage.
-
Please power it on and let it run occasionally. Please avoid using the unit in a room where cigarettes are smoked. It is impossible to clean optical component parts if they are contaminated by nicotine or tar. This might lead to performance degradation.
* DO NOT allow any unqualified person to install the unit.
Be sure to ask your dealer to install the unit (e.g. attaching it to the ceiling) since special technical knowledge and skills are required for installation. If installation is performed by an unqualified person, it may cause personal injury or electrical shock.
Getting Started
.
4
Power cord
Power cord
For European continent countries
For United Kingdom
Green-and-yellow Blue Brown
Fuse
: Earth : Neutral : Live
POWER CONNECTION
WARNING:
WARNING:
Do not cut off the main plug from this equipment.
The power supply voltage rating of this product is AC110V – AC240V. Use only the power cord designated by our dealer to ensure Safety and EMC. Ensure that the power cable used for the projector is the correct type for the AC outlet in your country. Consult your product dealer.
If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter or consult your dealer. If nonetheless the mains plug is cut off, dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the main supply. If a new main plug has to be fitted, then follow the instruction given below.
Dear Customer,
This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety.
European representative of JVC KENWOOD Corporation is: JVC Technical Services Europe GmbH Konrad-Adenauer-Allee 1-11 61118 Bad Vilbel Germany
THIS APPARATUS MUST BE EARTHED.
IMPORTANT (Europe only):
The wires in the mains lead on this product are colored Vert et jaune in accordance with the following cord:
IMPORTANT (Europe only):
POWER CONNECTION (United Kingdom only)
When replacing the fuse, be sure to use only a correctly rated approved type, re-fit the fuse cover.
IF IN DOUBT —— CONSULT A COMPETENT ELECTRICIAN.
Open the fuse compartment with the blade screwdriver, and replace the fuse. (* An example is shown in the illustration below.)
As these colors may not correspond with the colored making identifying the terminals in your plug, proceed as follows: The wire which is colored green-and-yellow must be connected to the terminal which is marked M with the letter E or the safety earth or colored green or green-and-yellow. The wire which is colored blue must be connected to the terminal which is marked with the letter N or colored black. The wire which is colored brown must be connected to the terminal which is marked with the letter L or colored red.
For USA and Canada only Use only the following power cord.
Getting Started
.
5
ENGLISH
Information for Users on Disposal of Old Equipment and Batteries
[European Union only]
These symbols indicate that equipment with these symbols should not be disposed of as general household waste. If you want to dispose of the product or battery, please consider the collection systems or facilities for appropriate recycling.
Notice: The sign Pb below the symbol for batteries indicates that this battery
contains lead.
Benutzerinformationen zur Entsorgung alter Geräte und Batterien
[Nur Europäische Union]
Diese Symbole zeigen an, dass derartig gekennzeichnete Geräte nicht als normaler Haushaltsabfall entsorgt werden dürfen. We nden Sie sich zur Entsorgung des Produkts oder der Batterie an die hierfür vorgesehenen Sammelstellen oder Einrichtungen, damit eine fachgerechte Wiederverwertung möglich ist.
Hinweis:
Notification:
Das Zeichen Pb unterhalb des Batteriesymbols gibt an, dass diese Batterie Blei enthält.
Informations relatives à l’élimination des appareils et des piles usagés, à l’intention des utilisateurs
[Union européenne seulement]
Si ces symboles figurent sur les produits, cela signifie qu’ils ne doivent pas être jetés comme déchets ménagers. Si vous voulez jeter ce produit ou cette pile, veuillez considérer le système de collection de déc hets ou les centres de recyclage appropriés.
La marque Pb en dessous du symbole des piles indique que cette pile contient du plomb.
Informatie voor gebruikers over het verwijderen van oude apparatuur en batterijen
[Alleen Europese Unie]
Deze symbolen geven aan dat appara tuur met dit symbool niet mag worden weggegooid als algemeen huishoudelijk afval. Als u het product of de batterij wilt weggooien, kun t u inzamelsystemen of faciliteiten voor een geschikte recycling gebruiken.
Opmerking: Het teken Pb onder het batterijsymboo l geeft aan dat deze batterij
lood bevat.
Battery
Batterie
Pile
Batterij
Products
Produkte
Produits
Producten
DEUTSCH
FRANÇAIS
NEDERLANDS
Información para los usuarios sobre la eliminación de baterías/pilas usadas
[Sólo Unión Europea]
Estos símbolos indican que el equipo con estos símbolos no debe desecharse con la basura doméstica. Si desea desechar el pro ducto o batería/pila, acuda a los sistemas o centros de recogida para que los reciclen debidamente.
Atención: La indicación Pb debajo del símbolo de batería/pila indica que ésta
contiene plomo.
Baterías/pilas
Productos
ESPAÑOL / CASTELLANO
Getting Started
.
6
ITALIANO
Informazioni per gli utenti sullo smaltimento delle apparecchiature e batterie obsolete
[Solo per l’Unione Europea]
Questi simboli indicano che le apparecchiature a cui sono relativi non devono essere smaltite tra i rifiuti domestici generici. Se si desidera smaltire questo prodotto o questa batteria, prendere in considerazione i sistem i o le strutture di raccolta appropriati per il riciclaggio corretto.
Nota: Il simbolo Pb sotto il simbolo delle batter ie indica che questa batteria contiene
piombo.
Informação para os utilizadores acerca da eliminação de equipamento usado e pilhas
[Apenas União Europeia]
Estes símbolos indicam que o equipamento com estes símbolos não deve ser eliminado juntamente com o restante lixo doméstico. Se p retende eliminar o produto ou a pilha, utilize os sistemas de recolha ou instalações para uma reciclagem apropriada.
Aviso:
Σημείωση:
O sinal Pb abaixo do símbolo para pilhas indica que esta pilha contém chumbo.
Πληροφορίες για την απόρριψη παλαιού εξοπλισμού και μπαταριών
[ Ευρωπαϊκή Ένωση μόνο ]
Αυτά τα σύμβολα υποδηλώνουν ότι ο εξοπλισμός που τα φέρει δεν θα πρέπει να απορριφθεί ως κοινό οικιακό απόρριμμα . Εάν επιθυμείτε την απόρριψη αυτού του προϊόντος ή αυτής της μπαταρίας , χρησιμοποιήστε το σύστημα περισυλλογής ή εγκαταστάσεις για ανάλογη ανακύκλωση .
Το σύμβολο Pb κάτω από το σύμβολο μπαταρίας υποδηλώνει ότι η μπαταρία περιέχει μόλυβδο .
Brugerinformation om bortskaffelse af gammelt udstyr og batterier
[Kun EU]
Disse symboler angiver, at udstyr med disse symboler ikke må bortskaffes som almindeligt husholdningsaffald. Hvis du ønsker at smide dette produkt eller batteri ud, bedes du overveje at bruge indsamlingssystem et eller steder, hvor der kan ske korrekt gen brug.
Bemærk: Tegnet Pb under symbolet for batterierne angiver, at dette batteri
indeholder bly.
Batteria
Pilha
Μπαταρία
Batteri
Prodotti
Produtos
Προϊόντα
Produkter
PORTUGUÊS
ΕΛΛΗΝΙΚΑ
DANSK
Tietoja vanhojen laitteiden ja akkujen hävittämisestä
[Vain Euroopan unioni]
Nämä symbolit ilmaisevat, että symboleilla merk ittyä laitetta ei tulisi hävittää tavallisen kotitalousjätteen mukana. Jos haluat hävit tää tuotteen tai sen akun, tee se hyödyntämällä akkujen keräyspisteitä tai muita kier rätyspaikkoja.
Huomautus: Akkusymbolin alapuolella oleva Pb-merk intä tarkoit taa, että akku
sisältää lyijyä.
Akku
Tuotteet
SUOMI
Getting Started
.
7
SVENSKA
Information för användare gällande bortskaffning av gammal utrustning och batterier
[Endast den Europeiska unionen]
Dessa symboler indikerar att utrustning med dessa symboler inte ska hanteras som vanligt hushållsavfall. Om du vill bortsk affa produkten eller batteriet ska du använda uppsamlingssystem eller inrättningar för lämplig återvinning.
Observera: Märkningen Pb under symbolen för batterier indikerar att detta batteri
innehåller bly.
Opplysninger til brukere om kassering av gammelt utstyr og batterier
[Bare EU]
Disse symbolene viser at utstyr med dette symbolet, ikke skal kastes sammen med vanlig husholdningsavfall. Hvis du vil kass ere dette produkte t eller batteriet, skal du vurdere å bruke innsam lingssystemene eller andre muligheter for riktig gjenbruk.
Merk:
Уведомление:
Tegnet Pb under symbolet for batterie r, viser at batteriet inneholder bly.
Сведения для пользователей по утилизации старого оборудования и батарей
[только для Европейского союза]
Данные символы указывают на то, что оборудование, на которое они нанесены, не должны утилизироваться, как обычные бытовые отходы. При необходимости утилизировать такое изделие или батарею обратитесь в специальный пункт сбора для их надлежащей переработки.
Надпись Pb под символом батар ей указывает на то, что данная батарея содержит свинец.
Informace pro uživatele k likvid aci starého zařízení a baterií
[Pouze Evropská unie]
Tyto symboly označují, že produkty s těmito symboly se nesmí likvidovat jako běžný odpad. Pokud chcete produkt nebo baterii zlikvidovat, využijte sběrný systém nebo jiné zařízení, které zaji stí řádnou recyklaci.
Bemærk: Značka Pb pod symbolem pro ba te rie znamená, že tato baterie
obsahuje olovo.
Batteri
Batteri
Батарея
Baterie
Produkter
Produkter
Изделия
Produkty
NORSK
Informacje dla użytkowników dotyczące poz bywania się zużytego sprzętu i baterii
[Tylko kraje Unii Europejskiej]
Te symbole oznaczają, że sprzę tu nie należy wyr zucać razem z odpadami gospodarczymi. Jeśli trzeba po zbyć się tego produktu lub ba terii, proszę skorzystać z systemu odbioru lub urządzeń do zbió rki odpadów elektronicznych, w celu odpowiedniego ponowne go ich przetworzenia.
Uwaga: Oznaczenie Pb, znajdujące się pod symbole m baterii wskazuje, że ta
bateria zawiera ołów.
Bateria
Produkty
POLSKI
Getting Started
.
8
MAGYAR
Felhasználói információ az elhasznált be rendezések és akkumulátorok elhelyezéséről
[Csak az Európai Unióban]
Ez a szimbólum azt jelzi, hogy a berendezés nem helyezhető az általános háztartási hulladék közé. Ha meg szeretne szabadulni a terméktől vagy az akkumulátortól, akkor legyen tekintettel az gyűjtő rendszerre vagy intézményekre a megfelelő hasznosítás érdekében.
Megjegyzés: Az alábbi Pb szimbólum - ha az akkum ulátoron megtalálható - azt
jelzi, hogy az akkumulátor ólmot tartalmaz.
Informacije za korisnike o odlaganju stare opreme i baterija
[Samo u zemljama gde se primenjuje]
Ovi simboli ukazuju da proizvod i baterije sa ovim simbolom ne smeju biti odloženi kao nesortiran kućni otpad. Ako želite da ih se rešite, molimo vas da ne upotrebljavate običnu kantu za đubre. Postoje zasebni sistemi za prikupljanje ovakvih proizvoda.
Naznaka: Hemijski simbol Pb ispod simbola za baterije ukazuje na to da li baterija
sadrži olovo.
Akkumulátor
Baterija
Termékek
Produkt
Cрпска
Getting Started
.
9
Contents
Getting Started
Getting Started
Safety Precautions .................................................. 2
Accessories/Optional Accessories ........................ 11
Check the Accessories ...................................... 11
Optional Accessories ......................................... 11
Controls and Features ........................................... 12
Main Unit - Front ................................................ 12
Main Unit - Bottom ............................................. 12
Main Unit - Rear ................................................. 13
Main Unit - Input Terminals ................................ 14
Remote control (sold separately, model no. RM-
MH13G) ............................................................. 15
Loading Batteries into the Remote Control (Sold
Separately) ........................................................ 16
Effective Range of Remote Control (Sold
Separately) ........................................................ 16
Set up
Installing the Projector ........................................... 17
Precautions during Installation ........................... 17
Precautions during Mounting ............................. 19
Adjusting the Position ........................................ 20
Connecting the Projector ....................................... 21
Connecting to the HDMI Input Terminal (Digital
Input) ................................................................. 21
Connecting to the LAN Terminal ........................ 22
Connecting to the RS-232C Terminal ................ 22
Connecting to the REMOTE Terminal ............... 22
Connecting the Power Cord (Supplied Accessory)
........................................................................... 23
Operate
Viewing Videos ...................................................... 24
Adjust/Set
Adjustments and Settings in the Menu .................. 26
List of Menu Items ............................................. 26
Picture Adjust .................................................... 28
Input Signal ........................................................ 32
Installation ......................................................... 34
Display Setup .................................................... 40
Function ............................................................. 41
Information ......................................................... 42
Maintenance
Replacing the Lamp .............................................. 43
Lamp Replacement Procedure .......................... 43
Replacing the Attachment ................................. 45
Resetting the Lamp Time ................................... 50
Maintaining the Cabinet and Remote Control (Sold
Separately) ............................................................ 50
Cleaning and Replacing the Filter ......................... 51
Troubleshooting
Troubleshooting .................................................... 52
When the following messages appear... ................ 54
Others
External Control .................................................... 55
RS-232C Specifications ..................................... 55
TCP/IP Connection ............................................ 55
Command Format .............................................. 56
Remote Control Code ........................................ 57
Communications Example ................................. 58
Specifications ........................................................ 59
Index ..................................................................... 65
Symbols used in this manual
P indicates a function that is supported by DLA­VS2200ZG.
O indicates a function that is supported by DLA­VS2200G.
Items not marked with any of the above symbols are supported by all models.
10

Accessories/Optional Accessories

Check the Accessories

Power cord (for USA) (about. 2 m) ......................................... 1 piece
.
Power cord (for EU) (about. 2 m) ............................................ 1 piece
.
Lamp attachment “UPPER 45-90 & REVERSE” (Use Area: B, Refer to
p. 17) and Installation verification seal .................................... 1 piece
.
0
INSTRUCTIONS (this book), warranty card, and other printed material are also included.

Optional Accessories

Getting Started
0
Remote control: Model no. RM-MH13G
0
AAA-size battery
0
Replacement lamp: model PK-L2313U
.
.
11

Controls and Features

AC
D
E
E
F
G
Getting Started

Main Unit - Front

.
A
Lens P
This is a projection lens. Do not look through the lens while an image is projected.
0
For O, the lens is sold separately.
B
Lens sheet
C
Remote Sensor (front)
Please aim the remote control (sold separately) at this area when using it.
* There is also a remote sensor at the rear.

Main Unit - Bottom

D
Indicator
Refer to “Indicator Display on the Main Unit” (p. 62).
E
Exhaust vent
Warm air is discharged to cool down the internal temperature. Do not block the vents.
F
Inlets (at 3 points on the rear/bottom)
The inlets take in air to cool down the internal temperature. Do not block or prevent the outflow of hot air. Doing so may cause the unit to malfunction.
* There are two inlets on the right and left sides at the rear of the unit.
G
Feet
The height and angle of the projector can be adjusted by turning the foot. (0 to 5 mm) (p. 20)
When the foot is removed, it can be used as the mounting holes for the ceiling mount bracket.
12

Main Unit - Rear

F
HJKL
F
I
[MENU]: Displays the menu
[BACK]: Returns to the previous menu
[JKH I] keys: Selects an item
[OK]: Confirms a selection
[INPUT]: Switches the input
A [STANDBY/ON]: Turns “on”/“off” the power
.
Getting Started
H
Input terminals
For details on the terminals. refer to “Main Unit - Input Terminals”p. 14.
I
Lamp cover
When replacing the light source lamp, remove this cover.
J
Operation panel
For more details, please refer to the “Operation panel” in the diagram below.
Operation panel
K
Remote Sensor (rear)
Please aim the remote control (sold separately) at this area when using it.
* There is also a remote sensor at the front.
L
Power input terminal
Connect the supplied power cord to this terminal.
.
13

Main Unit - Input Terminals

A B C
D
E
Enlarged View of Rear Face
Getting Started
.
A
[HDMI 1] input terminal
B
[HDMI 2] input terminal
For connecting to devices that support HDMI output. (p. 21)
It is fitted to the M3 lock hole. The depth of the screw hole is 3 mm.
C
[LAN] terminal (RJ-45)
The projector can be controlled by connecting it to a PC through the computer network for control commands to be sent to the projector.
D
[RS-232C] terminal (D-sub 9-pin
male)
The projector can be controlled by connecting a PC to this terminal.
* The LAN and RS-232C terminals cannot be used at the
same time. (p. 41)
E
[REMOTE] terminal (stereo mini
jack)
This terminal is used to connect the remote control directly to the projector with the cable.
14

Remote control (sold separately, model no. RM-MH13G)

A
D
E
G
H
F
B
I
J
L
K
M
N
C
Getting Started
A
B [STAND BY]
Turns off the power. (p. 25)
B
C [ON]
Turns on the power. (p. 24)
C
[COMPONENT]
Select either the [HDMI 1] or [HDMI 2] input. (p. 24)
D
[LENS CONTROL] P
For adjusting focus, zoom, and shift. (p. 34)
E
[HIDE]
Hides the image temporarily. (p. 24)
F
[JKH I] keys
For selecting an item.
G
[MENU]
Displays the menu, or hides the menu if it is displayed.
H
[GAMMA]
For setting the gamma level. (p. 29)
I
[COLOR TEMP]
For setting the color temperature. (p. 29)
J
[C.M.D.]
For setting frame interpolation. (p. 31)
K
[LIGHT]
Illuminates the buttons on the remote control.
L
[OK]
Confirms a selected item.
M
[BACK]
Returns to the previous menu.
N
[PICTURE MODE]
Switches the Picture mode to [NATURAL], [DYNAMIC], [USER1] to [USER6]. (p. 28)
CAUTION
0
Buttons marked by * are not available for use on this unit.
15

Loading Batteries into the Remote Control (Sold Separately)

30°
30°
20°
20°
Remote Control
This unit
A
B
30°
30°
20°
20°
20°
20°
20°
20°
Screen
Remote Control
This unit
Getting Started
.
0
If the remote control has to be brought closer to the projector to operate, it means that the batteries are wearing out. Replace the batteries with new ones (AAA).
0
Insert the batteries according to the t s marks. Be sure to insert the s end first.
0
If an error occurs while using the remote control, remove the batteries and wait for five minutes. Load the batteries again and operate the remote control.

Effective Range of Remote Control (Sold Separately)

When aiming the remote control toward the sensor on this unit (front or rear), ensure that the distance to the sensor is within 7 m. If the remote control fails to work properly, move closer to this unit.
Control through reflection off a screen, etc.
Ensure that the total of distance A (between this unit and the screen) and distance B (between the remote control and the screen) is within 7 m.
* As the efficiency of signals reflected from the remote
control unit varies with the type of screen used, the operable distance may decrease.
.
.
CAUTION
0
Do not put the remote control in a place with an exposure to direct sun light or high temperature.
16

Installing the Projector

Front
150 mm and above
200 mm and above
300 mm and above
300 mm and above
150 mm and above
10° 10°
Area B
Area B
Area A
45 °
90 °
30 °
-30 °

Precautions during Installation

Please read the following carefully before installing this unit.
Do not install at the following
This unit is a precision device. Please refrain from installing or using it at the following locations. Otherwise, it may cause fire or malfunction.
0
Dusty, wet and humid places
0
Places subject to oily smoke or cigarette smoke
0
On top of a carpet or bedding, or other soft surfaces
0
Places exposed to direct sunlight
0
Places with a high or low temperature
0
Do not install this unit in a room that is oily or subject to cigarette smoke. Even a small quantity of smoke or oiliness can have a long-term impact on this unit.
* This unit produces a great amount of heat, and is
designed to take in cool air to cool its optical components. Using the unit at the above locations may cause dirt to attach to the light path, thereby resulting in dark images or dull colors.
* Dirt that sticks to the optical components cannot be
removed.
Maintain clearance from the wall, etc.
As the unit discharges a large amount of heat, install it with adequate clearance from the surroundings as shown below.
.
Using the projector
This unit uses a projection lamp, which will heat up when in use. Please refrain from projecting in the following circumstances. Otherwise, it may cause fire or malfunction.
0
Projection with the unit stood vertically
.
0
Projection with the unit inclined at an angle
Horizontal direction: within ±10°
.
As shown in the illustration, this unit can be installed with a tilted angle, but for some areas there might be other conditions. Moreover, depending on the angle of installation, it may be necessary to have a hanging metal mount and secure installation base depending on the angle of the installation.

Set up

Leave the front area of the unit unblocked. If there is any obstructing object in front of the exhaust vent, hot air will flow back to the unit and cause it to heat up. Hot air flowing out of the unit may cause shadows on the screen (heat haze phenomenon).
.
Area A:Use the factory-installed lamp. The lamp is
attached to the Area A attachment (X mark and “0°” marking).
Area B:Replace with the supplied attachment (+
mark and “90°” marking). Refer to p. 45 on the replacement
procedures.
17
Installing the screen
Screen
Front
Install the unit and the screen such that they are perpendicular to each other.
.
0
Please choose a screen material with non-uniform patterns. Uniform patterns such as checks may cause interference patterns to occur.
Set up
0
In this case, you can change the size of the screen to make the interference patterns less noticeable.
Using the projector at a high altitude
When using this unit at a location that is higher than 900 m above sea level (low air pressure), set the “High Altitude Mode” to “On”. (p. 41)
18

Precautions during Mounting

Air Inlets
4 Locations
Securing (mounting) the projector
.
0
When this unit is to be mounted to a fixed position for use, install it horizontally.
0
Make sure to secure the main unit to prevent accidents such as during an earthquake.
Securing with screws
Securing the projector (ceiling mount)
.
0
Special expertise and techniques are required for mounting this unit to the ceiling. Make sure that you get the authorized dealer or a specialist to install it.
0
Take the necessary actions to prevent the main unit from falling off such as during an earthquake.
0
Regardless of the warranty period, JVC is not liable for any product damage caused by mounting the unit with non-JVC ceiling fittings or to an environment that is not suited for ceiling mount.
0
When using the unit with it suspended from a ceiling, pay attention to the surrounding temperature. When a heater is in use, the temperature around the ceiling may be higher than expected.
Set up
.
Remove the four feet at the bottom, and fasten using the screws (M5 screws, 13 to 23 mm).
* Using screws other than those designated may cause
the unit to break down.
* Leave a clearance of at least 10 mm from the bottom
surface of the unit to allow it to take in cool air.
19

Adjusting the Position

Contract
Extend
Feet
90
80
70
60
50
40
30
20
10
0
10 3020 40
Lens movement range
Horizontal lens shift (%)
Vertical lens shift (%)
Lens shift Range
Up to about 80% of the projected image
Horizontal Position: 0 % (Center)
Vertical Position
Up to about 34% of the projected image
Vertical Position: 0% (Center)
Horizontal Position
Adjusting the elevation angle of the projector
The height and inclination of the unit (0 to 5 mm) can be adjusted by turning the feet. Lift the unit and adjust the four feet.
Set up
.
Adjusting the position of the image
By using the lens shift feature of this unit, you can shift the image upward/downward or to the left/right. Set it to your preferred position.
20
.
0
The maximum vertical shift varies with the amount of horizontal shift. Similarly, the maximum horizontal shift also changes with the amount of vertical shift.
0
The values on the graph are intended as a guide. Use them for reference during installation.
0
To adjust the screen position, it is recommended to wait till the position becomes stable after projection before adjusting. The position may changed after projection depending on the attitude of the projector.

Connecting the Projector

HDMI Output Terminal
BD/DVD Recorder, etc.
Laptop, etc.
HDMI Cable (Sold Separately)
This Unit
To [HDMI 1] or [HDMI 2] input terminal
HDMI-DVI Conversion Cable (Sold Separately)
To [HDMI 1] or [HDMI 2] input terminal
This Unit
DVI Output Terminal
Desktop PC, etc.
0
Do not turn on the power until connection is complete.
0
The connection procedures differ according to the device used. For details, please refer to the instruction manual of the device to be connected.
0
This projector is used for projecting images. To output the audio of connected devices, please connect a separate audio output device, such as an amplifier or speaker.
0
The images may not be displayed depending on the devices and cables to be connected. Use only HDMI cables (sold separately) that are HDMI-certified.
0
Some cables cannot be connected to this unit due to the size of their connector cover.

Connecting to the HDMI Input Terminal (Digital Input)

Connecting via HDMI cable
Set up
.
0
If noise occurs, move the laptop away from this unit.
0
For a transmission bandwidth in compliance with the HDMI standard, a 340 MHz cable is recommended.
0
If the video is not displayed, try to reduce the length of the cable.
Connecting via HDMI-DVI conversion cable
.
0
If noise occurs, move the desktop PC away from this unit.
0
If the video is not displayed, try to reduce the length of the cable.
21

Connecting to the LAN Terminal

Desktop PC, etc.
Server
Hub
Network
Connection Cable
(Sold Separately)
This Unit
To [LAN] Terminal
RS-232C Terminal
Laptop, etc.
RS-232C Connection Cable (Sold Separately)
To [RS-232C] Terminal
This Unit
Wired Remote Control (Sold Separately)
Connection Cable
(Sold Separately)
To [REMOTE] Terminal
This Unit
Set up
.
0
The network is used to control this unit. It is not used for sending or receiving video signals.
0
Please contact your network administrator for information concerning the network connection.
0
For more information on control, please refer to “External Control” (p. 55).

Connecting to the RS-232C Terminal

22
.
0
For more information on control, please refer to “External Control” (p. 55).

Connecting to the REMOTE Terminal

.
0
For more information on the external infrared sensor and connecting cable, please contact your dealer.

Connecting the Power Cord (Supplied Accessory)

A
B
Power Cord (Supplied)
A
Connect the power cord supplied to the power input terminal on the main unit
B
Insert the supplied power plug into the wall outlet.
Precautions to prevent fire and electric shock
0
The voltage capacity of this unit is large. Please connect it directly to the wall outlet.
0
When you are not using the equipment, please unplug the power cord from the outlet.
0
Connect it using only the power cord supplied.
0
Do not use a voltage other than the indicated power voltage.
0
Do not damage, break or modify the power cord. Do not place a heavy object on the power cord, or heat or pull it. Doing so may damage the power cord.
0
Do not unplug the power cord with wet hands.
Set up
23

Viewing Videos

LAMP WARNING
STANDBY/ON
LAMP WARNING
STANDBY/ON
During lamp startup
“STANDBY/ON” lights up (green)
In standby state
“STANDBY/ON” lights up (red)
HDMI 1
HDMI 2
LAMP WARNING
STANDBY/ON
1
2
3

Operate

MEMO
0
When you are using this unit, be sure to remove the lens sheet.
0
Connect the power cord, and ensure that the “STANDBY/ON” indicator lights up in red.
1
Turn on the power
Projector unit: press the A [STANDBY/ON] button Remote control (sold separately): press the C [ON] button
0
The “STANDBY/ON” indicator light switches from red to green (light goes off after the unit starts up).
.
2
Choose the image to project
Projector unit: press the [INPUT] button (pressing the button each time switches the mode)
Remote control (sold separately): press the [INPUT] button ([HDMI 1] or [HDMI 2])
24
0
Play back the selected device to project the image.
To hide the image temporarily
Press the [HIDE] button on the projector unit or remote control (sold separately)
0
The “STANDBY/ON” indicator light starts to blink in green.
0
Press the [HIDE] button again to resume display of the image.
0
The power cannot be turned off when the image is temporarily hidden.
.
3
LAMP WARNING
STANDBY/ON
LAMP
WARNING
STANDBY/ON
In standby state
“STANDBY/ON” lights up (red)
In the Cool-down mode
“STANDBY/ON” blinking (red)
Turn off the power
Projector unit: press the A [STANDBY/ON] button Remote control (sold separately): press the B [STAND BY] button
0
While the “Are you sure you want to turn off?” message is displayed, press the button again.
0
The lamp turns off, and the “STANDBY/ON” indicator switches from a green light to a red blinking light.
0
After the light goes off, the fan will run for about 120 seconds to cool down the lamp (Cool-down mode). Do not disconnect the power cable while cooling is in progress.
0
After about 120 seconds, the “STANDBY/ON” indicator switches from a blinking red to a solid red light.
.
CAUTION
0
The power cannot be turned off within approximately 150 seconds after it has been turned on.
0
After the light goes off, the fan will run for about 120 seconds to cool down the lamp (Cool-down mode). Do not disconnect the power cable while cooling is in progress.
0
The power cannot be turned on again while cooling is in progress (120 seconds).
0
Pull out the power plug when the unit is not to be used for a prolonged period of time.
Operate
25

Adjustments and Settings in the Menu

Pressing the [MENU] button displays the menu. Press the [JKH I] keys to select an item, followed by pressing the [OK] button to confirm the selection.

List of Menu Items

Picture Adjust
IPicture Mode .................................................................................................................................................... p. 28
IContrast ............................................................................................................................................................ p. 28
IBrightness ......................................................................................................................................................... p. 28
IColor ................................................................................................................................................................. p. 28
ITint .................................................................................................................................................................... p. 28
IColor Temp. ...................................................................................................................................................... p. 29
IGamma ............................................................................................................................................................. p. 29
IAdvanced ......................................................................................................................................................... p. 30
9 Sharpness ................................................................................................................................................... p. 30
9 Color Management ...................................................................................................................................... p. 30
9 Clear Motion Drive ....................................................................................................................................... p. 31
9 Aperture ....................................................................................................................................................... p. 31
9 Lamp Power ................................................................................................................................................ p. 31
IReset ................................................................................................................................................................ p. 31
Input Signal

Adjust/Set

IHDMI ................................................................................................................................................................ p. 32
IPicture Position ................................................................................................................................................. p. 32
IMask ................................................................................................................................................................. p. 33
IShort Delay ....................................................................................................................................................... p. 33
Installation
ILens Control ..................................................................................................................................................... p. 34
9 Focus ........................................................................................................................................................... p. 34
9 Zoom ........................................................................................................................................................... p. 34
9 Shift ............................................................................................................................................................. p. 34
9 Image Pattern .............................................................................................................................................. p. 35
9 Lock ............................................................................................................................................................. p. 35
9 Lens Center ................................................................................................................................................. p. 35
IPixel Adjust ....................................................................................................................................................... p. 35
IInstallation Style ................................................................................................................................................ p. 36
26
Display Setup
IBack Color ........................................................................................................................................................ p. 40
IMenu Position ................................................................................................................................................... p. 40
IMenu Display .................................................................................................................................................... p. 40
ILine Display ...................................................................................................................................................... p. 40
ISource Display .................................................................................................................................................. p. 40
ILogo .................................................................................................................................................................. p. 40
Function
IOff Timer ........................................................................................................................................................... p. 41
IHigh Altitude Mode ........................................................................................................................................... p. 41
ICommunication Terminal .................................................................................................................................. p. 41
INetwork ............................................................................................................................................................ p. 41
IRemote Code ................................................................................................................................................... p. 41
ILamp Reset ...................................................................................................................................................... p. 50
Information
IInformation ........................................................................................................................................................ p. 42
Adjust/Set
27

Picture Adjust

Picture Mode
You can adjust the image quality according to the type of video image you are viewing.
Item Description
Natural Image quality that focuses on natural color and gradation reproduction. Suitable
for drama footage, etc.
Dynamic This is the picture setting best suited for viewing the picture in a room that cannot
be made completely dark.
User 1 to User 6 Enables user-defined image quality data to be saved and retrieved.
Contrast
For adjusting the difference in brightness to produce an image with contrast.
0
Setting range: -50 (little difference in brightness) to +50 (large difference in brightness)
Brightness
For adjusting the brightness of the video image.
0
Setting range: -50 (darker) to +50 (brighter)
Adjust/Set
Color
For adjusting the color density of the video image.
0
Setting range: -50 (lighter) to +50 (deeper)
Tint
For adjusting the hue of the video image.
0
Setting range: -50 (reddish) to +50 (greenish)
28
Color Temp.
For setting the color temperature of the video image.
Preset
Setting Description
5500K, 6500K, 9500K Increasing the value enhances the blue tone of the video image, while
decreasing the value enhances the red tone.
* Select only when “PictureMode” is set to “Natural”/“User1,2,3”.
High Bright Color temperature that gives priority to brightness.
* When “PictureMode” is “Dynamic”, it is set only in “HighBright”.
Custom 1 to Custom 3 The color temperature of video images can be adjusted manually and
saved as one of the three customized settings.
* Select only when “PictureMode” is set to “Natural”/“User1 to 6”.
Custom
Setting Description
Gain Red, Gain Green, Gain Blue Adjusts each color in the bright parts of the video image.
0
Setting range: -255 (reduces the red/green/blue tone) to 0 (enhances the red/green/blue tone)
* Only “HighBright” and “Custom1,2,3” can be adjusted.
Offset Red, Offset Green, Offset Blue
Adjusts each color in the dark areas of the video image.
0
Setting range: -50 (reduces the red/green/blue tone) to +50 (enhances the red/green/blue tone)
Adjust/Set
Gamma
You can adjust the output value of the projected image with respect to the video signal input.
Setting
Normal Recommended setting for normal viewing.
* When “PictureMode” is “User4,5,6”, it is set only in “Normal”.
Custom 1 to Custom 3 Adjustable to a preferred gamma setting.
Description
29
Advanced
MENU
BACK
>>
0
0
0
0
MagentaBlue
Cyan
Green Yellow
Red
Adjustable range when red is selected: ± 30° with red as the center
Clockwise rotation: -
Counterclockwise rotation: +
A
C
D
B
Back
Operate
Select
Exit
Picture Adjust
Brightness
Hue
Axis Position
Red
Color Selection
Reset
Off
Off
Pause
Custom 3
Custom 2
Custom 1
Saturation
Color Management
For fine-tuning the image quality.
Sharpness
Setting Description
Sharpness Emphasizes the outline of the video image.
0
Setting range: 0 (blurry) to +50 (sharp)
Detail Enhance Brings out details in the image, such as the hair or pattern of the clothes.
0
Setting range: 0 (weak) to +50 (strong)
Color Management
Each of the colors is adjustable according to the user’s preference.
A
Select the item to set (Custom 1 to Custom 3), and press the [OK] button.
B
Select “Pause” and press the [OK] button to set the background for the current adjustment
0
While adjustment is in progress, the input image is displayed as the background.
0
“On”: pauses when inputting the video images.
0
“Off”: does not pause when inputting the video images.
* If “Short Delay” is set to “ON”, “Pause” is not available.
C
Select “Color Selection”, and press the H I keys to select the color to adjust
0
Adjust/Set
For color adjustment, select the color from the following: “Red”, “Orange”, “Yellow”, “Green”, “Cyan”, “Blue”, “Magenta”.
0
Pressing the [HIDE] button enables you to check the image before adjustment.
D
Adjust the selected color
Item
Axis Position -30 to 30 Fine-tune the position of
Setting Range
Hue -30 to 30 Adjusts the hue (color
Saturation -30 to 30 Adjusts the color
Description
the central axis of the selected color.
tone).
saturation (vividness).
-30 (dull) to +30 (vivid)
Brightness -30 to 30 Adjusts the brightness.
0
Selecting “Reset” resets all the adjustment data.
30
-30 (dark) to +30 (bright)
Clear Motion Drive
For reducing the after-image, which occurs in a fast-moving scene.
0
For some scenes, interpolation may cause distortion in the image. In this case, set to “Off”.
0
Pressing the [C.M.D.] button each time switches the mode in the following sequence: “Off”"“Mode1”"“Mode2” "“Off”...
Setting Description
Off Interpolation is not performed.
Mode1 Black insertion weak.
Mode2 Black interpolation strong.
* C.M.D. is the abbreviation for Clear Motion Drive.
* The [C.M.D.] button is positioned differently on the remote control depending on the model in use. (p. 15)
Aperture
For adjusting the amount of opening of the optical iris.
0
Stopping down the iris reduces the brightness, while opening it up increases the contrast.
0
Setting range: -15 (stops down) to 0 (opens up) P
0
Setting range: -7 (stops down) to 0 (opens up) O
Lamp Power
The brightness of the lamp can be set to “Low” or “High”.
0
The factory setting varies with the “Picture Mode”.
0
Continuous use at the “High” setting may cause the lamp to darken faster.
Reset
For restoring the image quality adjustment settings to the factory default.
Adjust/Set
31

Input Signal

HDMI
Setting is enabled when the HDMI input terminal is selected.
Input
For setting the dynamic range (gradation) of the video input.
0
If the dynamic range is not appropriate, the bright areas become overexposed, and the dark areas become underexposed.
Setting Description
0-255 (PC) Select this setting if you are inputting PC signals (dynamic range: 0 - 255).
16-235 (Video) Select this setting if you are inputting video signals (dynamic range: 16 - 235).
Level Check
For checking the dynamic range of the video input.
Color Space
For setting the color space of the input signal.
Setting
Auto Detects “YCbCr(4:4:4)”, “YCbCr(4:2:2)”, and “RGB” automatically.
Adjust/Set
YCbCr(4:4:4) Select this setting when inputting YCbCr(4:4:4) video signals.
YCbCr(4:2:2) Select this setting when inputting YCbCr(4:2:2) video signals.
RGB Select this setting when inputting RGB video signals.
Description
Picture Position (Horiz./Vert.)
Adjust the position if the edges of the image are partially missing due to the timing of horizontal and vertical synchronization signals.
* If “Short Delay” is set to “ON”, “Picture Position” is not available.
32
Mask
Mask: black strip around the periphery
On
Off
For hiding the peripheral area of the image with a mask (black strip).
Setting Description
Off Not masked.
2.5% Masks about 2.5% of the peripheral area of the image.
5% Masks about 5.0% of the peripheral area of the image.
Custom Masks about 0% to 5% of the four sides of the image.
Short Delay
Supports only 1080p50/60 signals.
The interval time of the source signal and the projector image is shortened.
0
If “Short Delay” is set to “ON”, “Picture Position” is not available.
Adjust/Set
33

Installation

BACK
Back
Select
Operate
Focus
Lens Control
Shift (Screen Position)
Adjustment
Zoom (Screen Size)
Adjustment
ABCD
ABCD
ABCD
Focus Adjustment
Lens Control P
Focus / Zoom / Shift
For adjusting the lens according to the projection position
A
Press the [LENS CONTROL] button, and use the [JKH I] keys to adjust Focus, Zoom (screen size), and Shift (screen position)
.
0
Pressing the [LENS CONTROL] or [OK] button each time switches the mode in the following sequence: “Focus” "“Zoom”"“Shift”"“Focus”...
Adjust/Set
.
B
Press the [BACK] button once, or the [MENU] twice, to end adjustment.
34
Image Pattern
Setting Description
On Displays the lens adjustment pattern.
Off Displays external signals, and does not display the lens adjustment pattern.
Lock
Setting Description
On Locks the lens to prevent any erroneous operation on the adjustments.
0
Operation of the lens control feature is disabled when “On” is selected.
Off Does not lock the lens.
The focus, zoom, and shift settings can be saved or retrieved, so you can switch easily to a different aspect ratio (screen size) according to the image.
Lens Center
Returns the lens position to the center.
Pixel Adjust
Adjust
For setting the adjustment feature to “On” or “Off”.
Adjust Area
Setting Description
Whole Adjusts the entire image.
Zone Enables fine adjustment of each zone by dividing the screen into 11 vertical x 11
horizontal zones.
Adjust/Set
Adjust Color
For selecting the color to adjust (“Red” or “Blue”).
Adjust Pattern Color
For setting the adjustment pattern color to “White” or “Yellow / Cyan”.
Adjust(Pixel)
When “Adjust Area” is set to “Whole”, adjustment can be made by moving in units of one pixel on the screen of the color selected in “Adjust Color”.
Æ “Operation procedure for Whole Adjust (Pixel)” (p. 37
* Adjustment cannot be made when “Adjust Area” is set to “Zone”.
Setting
H (Horizontal) Setting range: -2 (moves red/blue to the left) to +2 (moves red/blue to the right)
V (Vertical) Setting range: -2 (moves red/blue downward) to +2 (moves red/blue upward)
Description
35
Adjust(Fine)
When “Adjust Area” is set to “Whole”, adjustment can be made by moving in units of 1/16 pixel on the screen of the color selected in “Adjust Color”.
Æ “Operation procedure for Whole Adjust (Fine)” (p. 38
When “Adjust Area” is set to “Zone”, the screen is divided into 11 vertical x 11 horizontal zones, and fine adjustment of each zone is possible.
Æ “Operation procedure for Zone Adjust” (p. 39
Setting Description
H (Horizontal) Setting range: -31 (moves red/blue to the left) to +31 (moves red/blue to the right)
V (Vertical) Setting range: -31 (moves red/blue downward) to +31 (moves red/blue upward)
Reset
Restores all pixel adjustment data to the factory default.
Installation Style
For setting to “Front”, “Ceiling Mount (F)”, “Rear”, or “Ceiling Mount (R)” according to the installation status of the projector.
0
“Front” or “Ceiling Mount (F)” is set when projector is installed in the front with respect to the screen.
0
“Rear” or “Ceiling Mount (R)” is set when projector is installed in the rear with respect to the screen.
Adjust/Set
36
Operation procedure for Whole Adjust (Pixel)
Color A.
GAMMA
BACK
ADJUST.
COLOR.
Color P.
LENS.AP
A. Area
PIC.
TEMP ADJ.
H 0 V 0
Back
Operate
Select
Red
Whole Adjust (Pixel)
Pixel Adjust
V (Vertical)
H (Horizontal)
Adjustment (Pixel) Window
Adjustment Pattern
Color A.
GAMMA
BACK
ADJUST.
COLOR.
Color P. A. Area
PIC.
TEMP
LENS.AP
ADJ.
H 0
V 0
Red
Whole Adjust (Pixel)
Pixel Adjust
Back
Operate
Select
Remote Control Operation Guide
Color for Adjustment
Pixel Adjustment Setting
For making general adjustments to slight color fringing in the horizontal/vertical directions of the video image.
A
Set “Adjust Area” to “Whole”
B
Select “Adjust Color” and “Adjust Pattern Color”
C
Select “Adjust(Pixel)”, and press the [OK] button
0
The selected adjustment pattern and Adjustment (Pixel) window are displayed.
.
D
Press the [OK] button to enter the Adjustment mode
E
Use the [JKH I] keys to move and adjust the pixels in the vertical and horizontal directions across the entire screen.
0
The adjustment setting appears at the center of the Adjustment (Pixel) window.
.
F
After adjustment is complete, press the [BACK] button to exit the Adjustment mode
Remote Control Operation Guide
Button Name
Description of Operation
[GAMMA] Changes “Adjust Color”.
[COLOR TEMP.] Switches between “Adjust(Pixel)” and “Adjust(Fine)”.
0
Switches to “Adjust(Pixel)” when “Adjust Area” is set to “Zone”.
[LENS.AP] Changes “Adjust Pattern Color”.
[PIC ADJ.] Switches “Adjust Area”.
0
A zone cursor appears on the adjustment pattern when the “Zone” setting is selected.
Adjust/Set
37
Operation procedure for Whole Adjust (Fine)
Color A.
GAMMA
BACK
ADJUST.
COLOR.
Color P.
LENS.AP
A. Area
PIC.
TEMP ADJ.
H 0 ( 0 / 0 ) V 0 ( 0 / 0 )
Red
Pixel Adjust
Whole Adjust (Fine)
V (Vertical)
H (Horizontal)
Fine Window
Adjustment Pattern
Back
Operate
Select
H −20 (−20 / −20 V 5 ( 5 / 5)
Color A.
GAMMA
BACK
ADJUST.
COLOR.
Color P.
LENS.AP
A. Area
PIC.
TEMP ADJ.
H 0 ( 0 / 0 ) V 0 ( 0 / 0 )
Red
Pixel Adjust
Whole Adjust (Fine)
Indicates the maximum and minimum misalignment value of the entire screen.(Max. / Min.)
Adjustment Setting
Remote Control Operation Guide
Color for Adjustment
Pixel Adjustment Setting
Back
Operate
Select
For making general adjustments on the misalignment of the entire screen using “Adjust(Pixel)”, followed by making fine adjustments.
A
Set “Adjust Area” to “Whole”
B
Select “Adjust Color” and “Adjust Pattern Color”
C
Select Adjust(Fine), and press the [OK] button
0
The selected adjustment pattern and Fine window are displayed.
0
The adjustable range may be smaller depending on the pixels being adjusted on the entire screen.
.
D
Press the [OK] button to enter the Adjustment mode
E
Use the [JKH I] keys to move and adjust the pixels in the vertical and horizontal directions across the entire screen.
Adjust/Set
0
The adjustment setting appears at the center of the Fine window.
.
F
After adjustment is complete, press the [BACK] button to exit the Adjustment mode
MEMO
0
If both the maximum overall screen misalignment of H (horizontal direction) and V (vertical direction) are “31”, you cannot select a value that is larger than the displayed setting even when the adjustment setting is lower than the maximum value.
0
If the minimum overall screen misalignment is “-31”, you cannot select a value that is smaller than the displayed setting even when the adjustment setting is higher than the minimum value.
38
Operation procedure for Zone Adjust
Color A.
GAMMA
BACK
ADJUST.
COLOR.
Color P.
LENS.AP
A. Area
PIC.
TEMP ADJ.
Red
Pixel Adjust
H 0
0 / 0
V 0
Position
Zone Adjust
V (Vertical)
H (Horizontal)
Zone Adjustment Window
Zone Cursor
Adjustment Pattern
Back
Operate
Select
H −31 V   7
Color A.
GAMMA
BACK
ADJUST.
COLOR.
Color P.
LENS.AP
A. Area
PIC.
TEMP ADJ.
Red
Pixel Adjust
H 0
0 / 0
8 / 5
V 0
Position
Position
Zone Adjust
Adjustment Setting
Cursor Position
Remote Control Operation Guide
Color for Adjustment
Pixel Adjustment Setting
Back
Operate
Select
For fine-tuning misalignments on a part of the screen after adjusting the overall screen misalignment using “Adjust(Pixel)” and “Adjust(Fine)”.
0
The screen can be divided vertically and horizontally into 10 sections for partial adjustments to be made.
A
Set “Adjust Area” to “Zone”
B
Select “Adjust Color” and “Adjust Pattern Color”
C
Select Adjust(Fine), and press the [OK] button
0
The selected adjustment pattern and Zone Adjustment window are displayed.
0
The adjustable range may be smaller depending on the pixels being adjusted on the entire screen.
.
D
Press the [JKH I] keys to move the cursor to the point to be adjusted
E
Press the [OK] button to enter the Adjustment mode
F
Use the [JKH I] keys to move and adjust the pixels in the vertical and horizontal directions across the entire screen.
0
The adjustment setting appears at the center of the Zone Adjustment window.
Adjust/Set
.
G
After adjustment is complete, press the [BACK] button to exit the Adjustment mode
39

Display Setup

Back Color
For setting the color of the background to “Blue” or “Black” when there is no input signal.
Menu Position
For setting the display position of the menu.
Menu Display
Setting Description
15sec The menu display disappears if it is not operated for 15 seconds.
On Displays the menu at all times.
Line Display
Setting Description
5sec Shows the input terminal for 5 seconds when input is switched.
Off Not displayed.
Adjust/Set
Source Display
Setting Description
On Displays the signal when input is switched.
Off Not displayed.
Logo
Setting Description
On Displays the “D-ILA” logo for 5 seconds during startup.
Off Not displayed.
40

Function

Off Timer
For setting the timing to power off the unit automatically (“1 Hour”, “2 Hours”, “3 Hours”, or “4 Hours”) when it is not operated for a period of time.
High Altitude Mode
Set to “On” when using the projector at a location of low atmospheric pressure (higher than 900 m above sea level).
Communication Terminal
For setting the external control terminal to be used to “RS-232C” or “LAN”.
Network
Setting Description
DHCP Client On Obtains the IP address automatically from the DHCP server inside the connected
network.
Off For configuring the network settings manually.
IP Address For configuring the IP address.
Subnet Mask For configuring the subnet mask.
Default Gateway For configuring the default gateway.
MAC Address Displays the MAC address of the unit.
Set Applies the network settings.
Adjust/Set
Remote Code
For changing the remote control code.
0
You need to configure the remote control according to the settings of this unit. On the remote control unit, press the [MENU] and [BACK] buttons at the same time for three seconds or longer to switch the code.
0
The backlight of the remote control blinks 3 times: change the remote control code to “A”
0
The backlight of the remote control blinks 2 times: change the remote control code to “B”
Setting Description
A Change the remote control code from “B” to “A”.
B Change the remote control code from “A” to “B”.
Lamp Reset
For resetting the lamp time to “0”.
Æ “Resetting the Lamp Time” (p. 50
41
Glossary of Network Terminology
DHCP : Abbreviation for Dynamic Host Configuration Protocol. This is a protocol for the network
to assign an IP address automatically to the connected device.
IP Address : Numeric characters for identifying the device that is connected to the network.
Subnet Mask : Numeric characters that define the bit count used for the network address that is a
segment of the IP address.
Default Gateway : Server for communicating beyond the network that is divided by the subnet mask.
MAC Address : Abbreviation for Media Access Control address. This is a number that is unique to each
network adapter. Each of the network adapters is assigned with a unique MAC address.

Information

During video signal input
Setting Description
Input Displays video input terminal.
Source Displays the input source.
Deep Color Displays the color bit depth of the input video signal.
0
Displayed when Deep Color information is received from the source device.
Lamp Time Displays the lamp time.
Soft Ver. Displays the firmware version.
Adjust/Set
During PC signal input
Setting Description
Input Displays video input terminal.
Resolution Displays the image resolution.
H Frequency Displays the horizontal frequency.
V Frequency Displays the vertical frequency.
Deep Color Displays the color bit depth of the input video signal.
0
Displayed when Deep Color information is received from the source device.
Lamp Time Displays the lamp time.
Soft Ver. Displays the firmware version.
42

Replacing the Lamp

Handle
The lamp is a consumable item. If the image appears dark or the lamp goes out, replace the lamp unit.
0
When the lamp replacement time approaches, the user is notified with a message displayed on the screen and by the indicator. (p. 62)

Lamp Replacement Procedure

3
CAUTION
0
Do not insert your hands into the opening of the lamp. This could cause significant deterioration in the performance of the equipment, or lead to injury and electric shock.
0
Do not replace the lamp immediately after the unit has been used. Allow a cooling period of at least one hour before replacement. The temperature of the lamp is still high, and may cause burn injuries.
0
Do not subject the lamp unit to shock. Doing so may cause lamp blowout.
0
Do not use a flammable air duster to clean the internal parts of the unit. Doing so may cause fire.
0
Use only genuine replacement parts for the lamp unit. Also, never attempt to reuse an old lamp unit. This may cause the unit to malfunction.
0
Do not touch the surface of a new lamp. Doing so may shorten the lamp life and cause lamp blowout.
0
When replacing the lamp, be careful not to injure yourself as the lamp may be broken.
0
When replacing the lamp of a projector suspended from the ceiling, work at height is required. This is a dangerous operation. Please consult our service center.
Loosen the screws of the lamp unit
0
Loosen the screws with a t screwdriver.
.
4
Pull out the lamp unit
0
Grasp the handle and pull out the lamp unit.

Maintenance

Remove the power plug from the
1
outlet
2
Remove the lamp cover
0
Remove the screw with a t screwdriver
.
.
5
Replace the lamp
0
For more details, refer to “Replacing the Attachment”p. 45.
43
6
Handle
Install the new lamp unit
.
Tighten the screws of the new lamp
7
unit
0
Tighten the screws with a t screwdriver.
.
Maintenance
8
Attach the lamp cover
0
Insert the two tabs at the top and bottom of the lamp cover into the unit.
0
Tighten the screws with a t screwdriver.
MEMO
Usable lamp life
0
When the lamp is used with “Lamp Power” set to “Low” , the lamp life on this unit is approximately 4000 hours. This is the average usable time and not a guaranteed value.
0
The lamp life may not reach 4000 hours depending on the operating conditions.
0
When the lamp has reached the end of its usable life, deterioration progresses rapidly.
0
When the video image appears dark, when the color tone looks unnatural, or when the image flickers, replace the lamp unit with a new one promptly.
Purchasing a lamp unit
Please consult your authorized dealer or nearby service center.
0
Lamp unit Product no.: PK-L2313U
*Lamps with a different product number or those for other
projector models cannot be used.
Information about the lamp
An ultra-high pressure mercury lamp with a high internal pressure is used in the projector.
Due to the characteristics of this lamp, it may blow out with a loud noise or go out when it is subject to shock or after using for a prolonged period of time (the time before the lamp blows out or goes out varies considerably with each lamp as well as the operating conditions).
After replacing the lamp
0
Do not place the removed lamp unit at a place that is within reach by children or anywhere near inflammable items.
0
Dispose used lamp units in the same way as fluorescent lamps. Follow the regulations of your local community for disposal.
44
.

Replacing the Attachment

Installation Verification Seal “UPPER45°-DOWN90°”
Stamp of “0°”
X” Hole
Installation Verification Seal “UPPER45°-90°&REVERSE”
Stamp of “90°”
“+” Hole
Area B
Area B
Area A
45 °
90 °
30 °
-30 °
Attachment and the placement area
0
As default, an attachment for Area A (with “X” hole and stamp of “0°”) is attached on the lamp. Use the lamp as it is if you use with the angle in
Area A. And stick the Installation verification seal on the lamp cover to avoid using in the wrong position. Refer to p. 49 on how to stick the Installation verification seal.
0
Replace with the supplied attachment (with “+” hole and stamp of “90°”) if you use in Area B. In this case, replace the Installation verification seal.
0
After the replacement, keep the removed seal and attachment together.
Area A Attachment
Area B Attachment
.
.
Maintenance
45
Lamp attachment removal procedure
Bending
Figure 2
Figure 1
Figure 3
Figure 4
1
Bend the clasp coupling of the lamp attachment vertically (see Figure 2)
0
If you remove it without bending it vertically, it will be difficult to install the next time.
.
Remove the clasp coupling of the lamp unit and the lamp attachment in the direction
2
of the arrow
Maintenance
3
Make sure that the clasp is removed from the lamp attachment
46
.
.
4
Figure 5
“A”
Lamp unit
“a”
“b”
“a”
Lamp attachment
Figure 2
Figure 1-2
Figure 1-1
X” or “+” Hole
X” or “+” Hole
Stamp of “0°” or “90°”
Figure 3
“a”
CAUTION
In case the lamp attachment is bent in any direction other than stated in the written instructions, or if it is modified, or remodeled, the lamp attachment will be damaged or break off. This may lead to failure of the main unit of the projector. Moreover, in case it is repeatedly installed and removed, it may be possible that the “a” section of the clasp section breaks off. In this case, please purchase and use a new replacement lamp attachment. As the folding section of the “b” section is fragile, please be careful when bending it in the direction of the arrow.
Remove the clasp coupling of lamp attachment on the reverse side and the lamp unit
.
Lamp attachment replacement procedures
Insert the “a” section of the lamp attachment into the “A” section of the lamp unit.
1
Hang the lamp attachment into the clasp-shaped part of the lamp unit
.
.
Maintenance
47
Fit the “b” section of the lamp attachment (see Figure 1-2) into the clasp-shaped part
Figure 4
pushing
into
Figure 5
“c”
Figure 6
Bending by pressing
2
of the lamp unit by pressing the former into the latter
.
As shown in Figure 5, make sure that the lamp attachment is coupled with the clasp
3
of the lamp unit
Maintenance
Bend the “c” section of the lamp attachment (see Figure 5) by pressing it in the
4
direction of the lamp unit
48
.
.
As shown in Figure 7, make sure that the lamp attachment is coupled with the clasp
Figure 7
Installation verification seal
5
of the lamp unit
.
0
When replacing the lamp, please do not forget to remove the lamp attachment.
Attachment of the installation verification seal
1
After replacing the lamp, attach the “installation verification seal” on the lamp cover
0
Attach the installation verification seal at the bottom right of the lamp cover.
.
0
The installation verification seal states “DOWN45 ° - 90 °”.
0
When the lamp attachment is removed, peel off the attached verification seal and keep it for further use.
Maintenance
49

Resetting the Lamp Time

MENU
BACK
RS-232C
A
Back
Operate
Select
Exit
Function
Lamp Reset
Remote Code
Communication Terminal
Off
Off
High Altitude Mode
Network
Off Timer
NoYes
Reset Lamp Time?
Press for 2 seconds or longer
Resetting the lamp time from the menu screen
Press the [MENU] button to display
1
the menu
Select “Function”"“Lamp Reset”
2
from the menu
.
On the Reset Lamp Time? screen,
3
select Yes and press the OK button
0
The lamp time is reset to zero.
.
Resetting the lamp time using the remote control
Insert the power plug into the power
1
outlet
Make sure that you operate the remote control in the Standby mode
2
(the power plug is inserted into the outlet, but the power is not turned on)
0
Press in the order as shown.
0
Make sure that you press a button within two seconds after the last button is pressed. Press the last button for at least two seconds.
.
0
The “LAMP” indicator and “STANDBY/ON” indicator blink alternately for three seconds. After that, the unit switches to the Standby mode.
MEMO
0
Maintenance
Reset the lamp time only when you have replaced the lamp. If the lamp time is reset while a lamp is in use, you may lose track of the timing for replacing the lamp. Doing so may result in using the lamp beyond the estimated limit, thereby causing lamp blowout.

Maintaining the Cabinet and Remote Control (Sold Separately)

0
Gently wipe off dirt on the cabinet with a soft cloth.
0
If it is extremely dirty, wet a cloth in water, wring dry and use it to wipe off the dirt, followed by wiping again with a dry cloth.
0
Pay attention to the following as the cabinet may deteriorate in condition or the paint may come off.
0
Do not wipe with thinner or benzine
0
0
50
Do not allow prolonged contact with rubber or plastic products
Do not spray volatile chemicals such as insecticide

Cleaning and Replacing the Filter

Pull out while pushing down the tab
Check that the left and right tabs are locked onto the unit
Clean the filter regularly Otherwise, the air intake efficiency may deteriorate, and malfunction may occur.
CAUTION
0
Make sure that you pull out the power plug from the outlet before cleaning or replacing the filter.
0
Before turning this unit upside down and placing it on the floor or a table, make sure that you lay a soft rag in advance to prevent the projector from being scratched.
3
Reinstall the inner filter
1
Remove the inner filter
.
2
Clean the filter
.
0
Wash the filter with water and dry it in a shaded area.
0
If the filter is extremely dirty, clean it with a neutral detergent. Put on rubber gloves when using a neutral detergent.
0
After washing the filter with water, make sure that it is completely dry before reinstalling. Otherwise, electric shock or malfunction may occur.
0
Do not clean the filter with a vacuum cleaner or air duster. The filter is soft and may be easily damaged.
.
If the filter is damaged or too dirty to be cleaned
0
Replace with a new filter. A dirty filter will dirty the internal parts of the unit and cause shadows to appear on the video image.
0
To purchase a new filter or when there is dirt in the internal parts of the unit, consult your authorized dealer or nearby service center.
0
Inner filter (exchangeable filter) Product no.: PC010661199
Maintenance
51

Troubleshooting

Before sending the unit to your authorized dealer for repair, please check the following points.
The following symptoms are not malfunctions.
You do not need to worry about the following symptoms if there is no abnormality on the screen.
0
A part of the top or front surface of the unit is hot.
0
A creaking sound is heard from the unit
0
An operating sound is heard from the inside of the unit.
0
Color smear occurs on some screens
This unit is a digital device. This unit may become unable to operate normally due to external static or noise. Perform the following operations when such malfunctions occur.
A
If the unit is in the Standby mode, pull out the power plug, followed by inserting it again
B
Press the A [STANDBY/ON] button on the main unit to turn on the power again
If “High Altitude Mode” is set to “On”, the fan spins at a higher speed when “Lamp Power” is set to “High” and produces a louder sound than normal.
Power is not supplied
Check Action Refer to
Is the power cord disconnected? Insert the power cord (plug) firmly. p. 23
Is the lamp cover properly shut? If the unit is in the Standby mode, remove the power plug
and close the lamp cover properly. After that, insert the plug again.
Is the lamp in the Cool-down mode? After exiting the Cool-down mode, turn on the power again. p. 25
p. 44
The unit works when power is turned on, but stops abruptly after a few minutes
Check Action Refer to
Are the air inlets and exhaust vent blocked?
Is the filter dirty? Clean the filter. p. 51
Leave proper clearance when installing the unit p. 12, 13
Video image does not appear

Troubleshooting

Is the correct external input selected? Select the correct external input terminal. p. 24
Is the power of the AV device turned on? Turn on the power of the AV device and play the video. p. 21
Is the AV device properly connected? Connect the AV device properly. p. 21
Are the correct signals being output from the AV device?
Is the cable in use an HDMI-certified cable?
Is the video image temporarily hidden? Press the [HIDE] button p. 24
Check Action Refer to
Set the AV device properly. p. 21
Use an HDMI-certified high-speed cable. Also, use as short a cable as possible.
p. 17
p. 21
52
Remote control does not work
Check Action Refer to
Are the batteries correctly loaded? Match the polarities (t s) correctly when loading the
batteries.
Are the batteries exhausted? Replace with new batteries. p. 16
Is there an obstructing object between the remote control and remote sensor?
Is the remote control held too far away from the unit?
Remove any obstructing object. p. 16
Hold the remote control closer to the sensor during use. p. 16
p. 16
Color does not appear or looks unnatural
Check Action Refer to
Is the AV device properly connected? Connect the AV device properly. p. 21
Is the image correctly adjusted? Adjust “Color” and “Tint” accordingly. p. 28
Video image is fuzzy
Check Action Refer to
Is the focus correctly adjusted? Adjust the focus. p. 34
Is the unit placed too near or too far away from the screen?
Set the unit at a correct distance from the screen. p. 60
Video images are missing
Check Action Refer to
Has screen mask been configured? Set “Mask” to “Off”. p. 33
Is the display position misaligned? Alter the “Picture Position” value so that the entire image
appears on the screen.
p. 32
Projected image is dark
Check Action Refer to
Is the lamp near exhaustion? Check the lamp time in the “Information” menu. Prepare a
new lamp unit or replace as soon as possible when the lamp is near exhaustion.
Is the image quality correctly adjusted? Adjust “Picture Adjust” and “Aperture”. p. 31
p. 42 p. 43
Troubleshooting
53
Power is cut off suddenly
No Input
HDMI 1
HDMI 1
Check Action Refer to
Has “Off Timer” been configured? Set “Off Timer” to “Off”. p. 41
The internal cooling fan emits a loud noise
Check Action Refer to
Is the exhaust vent blocked?
Check the condition of installation. p. 17 Is the unit used near a heater or air­conditioner?
There are small black or colored dots on the screen
The D-ILA device is manufactured using high-precision technologies, but there may be some (less than 0.01%) missing pixels or pixels that remain permanently lit. This is not a malfunction.

When the following messages appear...

Message Description Action
0
No device is connected to the input terminal
0
.
The input terminal is connected but there is no signal
A video signal that cannot be used with
.
this unit has been input (the names of input terminals such as “HDMI 1” will be displayed in yellow)
Input the video signals.
Input video signals that can be used.
Troubleshooting
54

External Control

15
69
This Unit
D6 D7D4 D5D2 D3D0 D1
Stop bitStart bit
Projector Control
Connection Authentication Procedure
PJA CK
PJ RE Q
PJ _O K
Within 5 Seconds
Controlling PC
3-way Handshake
TCP Port No. 20554
Establishment of TCP Connection
Projector
It is possible to control this unit by connecting it to a PC using an RS-232C cross cable (D-sub 9-pin). The projector can be controlled by connecting it to a PC through the computer network with a LAN cable for control commands to be sent to the projector.
0
Please use it after you have gained proper understanding from professional books or consulting the system administrator.

RS-232C Specifications

Pin No. Signal Function Signal Direction
2 RxD Receive data PC " This unit
3 TxD Transmission data This unit " PC
5 GND Signal ground
1, 4, 6 - 9 N/C
0
PC refers to the controller, such as a personal computer.
Mode Non-synchronous
Character length 8 bit
Parity None
Start bit 1
Stop bit 1
Data rate 19200 bps
Data format Binary

TCP/IP Connection

Before controlling via LAN, it is necessary to establish connection of the TCP layer by a “3-way handshake”, followed by sending out “PJREQ” and receiving “PJACK” within five seconds after the projector sends out “PJ_OK” for connection authentication. If you are unable to complete sending within five seconds, or when “PJ_NG” or “PJNAK” is received, check the operating status of the projector, followed by performing the steps again starting from establishment of a TCP connection,
.

Others

55

Command Format

The command between this unit and the computer consists of “Header”, “Unit ID”, “Command”, “Data” and “End”.
0
Header (1 byte), Unit ID (2 bytes), Command (2 bytes), Data (n bytes), End (1 byte)
Header
This binary code indicates the start of communication.
Binary Code Type Description
21 Operating command PC " This unit
3F Reference command PC " This unit
40 Response command This unit " PC
06 ACK This unit " PC (returns to PC after the command is accepted without
error)
Unit ID
This is a code that specifies the unit. The binary code is fixed at “8901”.
Command and data
Operating command and data (binary code)
Command Type Description
0000 Connection
check
5057
4950
5243 Remote
Power supply
Input When power is on
control
Check whether communication is enabled between this unit and the PC during standby.
During standby 31: Turns on the power When power is on 30: Turns off the power (Standby mode)
36: HDMI 1 37: HDMI 2
Sends the same code as the supplied remote control.
0
“Remote Control Code”p. 57
Operating command and data (binary code)
Command Type Description
5057 Power
supply
4950 Input When power is on
End
This code indicates the end of communication. The binary code is fixed at “0A”.
During standby or when power is on 30: Standby mode 31: When power is on 32: In the Cool-down mode 34: When error occurs on this unit
36: HDMI 1 37: HDMI 2
Others
56

Remote Control Code

Binary code is sent during communication.
0
The following applies to the case when the remote control code is “A”. In the case of “B”, add “36” to the beginning of the code.
Remote Control Button Name Binary Code
STAND BY 37 33 30 36
ON 37 33 30 35
HDMI 1 37 33 37 30
HDMI 2 37 33 37 31
LENS CONTROL 37 33 33 30
Aperture 37 33 32 30
HIDE 37 33 31 44
J
K
I
H
OK 37 33 32 46
37 33 30 31
37 33 30 32
37 33 33 34
37 33 33 36
Remote Control Button Name Binary Code
MENU 37 33 32 45
BACK 37 33 30 33
NATURAL 37 33 36 41
DYNAMIC 37 33 36 42
USER 37 33 44 37
C.M.D. 37 33 38 41
INFO 37 33 37 34
GAMMA 37 33 37 35
C. TEMP 37 33 37 36
PIC. ADJ. 37 33 37 32
57
Others

Communications Example

This section shows the communication examples of RS-232C.
Operating command
Type Command Description
Connection check PC " This unit: 21 89 01 00 00 0A
This unit " PC: 06 89 01 00 00 0A
Power (On) PC " This unit: 21 89 01 50 57 31 0A
This unit " PC: 06 89 01 50 57 0A
Power (Off) PC " This unit: 21 89 01 50 57 30 0A
This unit " PC: 06 89 01 50 57 0A
Input (HDMI 1) PC " This unit: 21 89 01 49 50 36 0A
This unit " PC: 06 89 01 49 50 0A
Remote control (MENU)
Reference command
Type Command Description
Power (On) PC " This unit: 3F 89 01 50 57 0A
Input (HDMI 1) PC " This unit: 3F 89 01 49 50 0A
PC " This unit: 21 89 01 52 43 37 33 32 45 0A This unit " PC: 06 89 01 52 43 0A
This unit " PC: 06 89 01 50 57 0A This unit " PC: 40 89 01 50 57 31 0A
This unit " PC: 06 89 01 49 50 0A This unit " PC: 40 89 01 49 50 36 0A
Connection check
When power is turned on from the Standby mode
When power is turned off (Standby mode) from power-on mode
When video input is set to HDMI 1
When the same operation as pressing the [MENU] button on the remote control is performed
When information on the power-on state is acquired
When information on HDMI 1 input is acquired
Others
58

Specifications

Product Name D-ILA Projector
Model Name DLA-VS2200ZG, DLA-VS2200G
Display Panel/Size D-ILA device *1, 2
0.7" (1980 x 1080 pixels) x 3 (total no. of pixels: approx. 6.22 million)
Projection Lens 2.0 x power zoom lens (1.4:1 to 2.8:1), motorized zoom and focus
Light-source Lamp 230 W ultra-high pressure mercury lamp [model no.: PK-L2313U]
Average lifespan: 4000 hours (“Low” mode)
Screen Size Approx. 60" to 200" (Aspect ratio of 16:9) P
Projection Distance Refer to p. 60. P
Input Compatibility Signal Refer to p. 62.
Display Resolution 1920 x 1080 pixels
HDMI Input Terminal Dual, HDMI 19-pin x 2 (HDCP-compatible) *3
Control Terminal RS-232C Terminal 1 system, D-sub 9-pin (male) (external control)
Remote Terminal 1 system, stereo mini jack (remote control)
LAN Terminal 1 system, RJ-45 plug
Power Requirements AC 110 to 240 V, 50/60 Hz
Power Consumption 360 W (during standby mode: 0.8 W)
Operation Environment Temperature: 5°C to 35°C; humidity: 20% to 80%; storage
temperature: -10°C to 60°C
Installation Height Below 5000 ft (1524 m)
Dimensions (Width x Height x Depth) Approx. 455 mm x 179 mm x 472 mm (excluding feet and protrusions)
Mass 14.7 kg (P)
13.5 kg (O)
Accessories Refer to p. 11.
*1 D-ILA is the abbreviation for Direct drive Image Light Amplifier.
*2 D-ILA devices are manufactured using extremely high-precision technology with a pixel effectiveness of 99.99%.
Only 0.01% or less of the pixels are either missing or would remain permanently lit.
*3 HDCP is the abbreviation for High-bandwidth Digital Content Protection system. The image of the HDMI input
terminal may not be displayed in some cases due to changes in the HDCP specifications.
59
Others
0
Design and specifications are subject to change without prior notice.
0
This projector is designed for use in Japan only, and cannot be used in any other country due to the different power voltage. This projector is designed for use in Japan only and can not be used in any other country.
0
Please note that some of the pictures and illustrations may have been abridged, enlarged or contextualized in order to aid comprehension. Images may differ from the actual product.
0
This unit is a “JIS C61000-3-2-compliant device”.
About Trademarks and Copyrights
HDMI, HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LCC.
Screen Size and Projection Distance
When a 16:9 screen is used P
Screen Size Projection Distance
Diagonal (Model) Width (mm) Height (mm) Wide-end (m) Tele-end (m)
60 1328 747 1.78 3.66
70 1549 872 2.09 4.28
80 1771 996 2.4 4.89
90 1992 1121 2.7 5.51
100 2214 1245 3.01 6.13
110 2435 1370 3.31 6.75
120 2656 1494 3.62 7.36
130 2878 1619 3.92 7.98
140 3099 1743 4.23 8.60
150 3320 1868 4.53 9.22
160 3542 1992 4.84 9.84
170 3763 2117 5.14 10.45
180 3984 2241 5.45 11.07
190 4206 2366 5.75 11.68
200 4427 2490 6.06 12.30
Others
60
When a 4:3 screen is used P
Screen Size Projection Distance
Diagonal (Model) Width (mm) Height (mm) Wide-end (m) Tele-end (m)
60 1219 914 2.22 4.49
70 1422 1067 2.60 5.24
80 1626 1219 2.98 6.00
90 1829 1372 3.36 6.75
100 2032 1524 3.74 7.51
110 2235 1676 4.11 8.26
120 2438 1829 4.49 9.02
130 2642 1981 4.87 9.77
140 2845 2134 5.25 10.53
150 3048 2286 5.63 11.28
160 3251 2438 6.00 12.04
* Projection to a 4:3 screen larger than 163" is equivalent to a size that is larger than 200" in the 16:9 format, and is
beyond our guarantee coverage.
When a 2.35:1 screen is used P
Screen Size Projection Distance
Diagonal (Model) Width (mm) Height (mm) Wide-end (m) Tele-end (m)
60 1402 597 1.95 3.91
70 1636 696 2.28 4.56
80 1870 796 2.60 5.21
90 2103 895 2.93 5.86
100 2337 995 3.26 6.51
110 2571 1094 3.58 7.16
120 2805 1193 3.91 7.81
130 3038 1293 4.23 8.47
140 3272 1392 4.56 9.12
150 3506 1492 4.88 9.77
160 3740 1591 5.21 10.42
170 3973 1691 5.53 11.07
180 4207 1790 5.86 11.72
190 4441 1890 6.19 12.37
200 4674 1989 6.51 13.02
61
Others
Types of Possible Input Signals
The indicator appears blinking.The indicator lights up.
LAMP WARNING
STANDBY/ON
LAMP WARNING
STANDBY/ON
LAMP WARNING
STANDBY/ON
LAMP WARNING
STANDBY/ON
LAMP WARNING
STANDBY/ON
When the video image is temporarily hidden (HIDE is on)
“STANDBY/ON” blinking (green)
During projection
All lights off
In the Cool-down mode
“STANDBY/ON” blinking (red)
During lamp startup
“STANDBY/ON” lights up (green)
In standby state
“STANDBY/ON” lights up (red)
LAMP WARNING
STANDBY/ON
When lamp replacement is near (lamp time has exceeded 2900 hours)
“LAMP” lights up (orange)
3900 hours)
Video
Digital Video Signal 480p/60 Hz, 576p/50 Hz, 720p/50 Hz, 720p/60 Hz, 1080p/50 Hz, 1080p/60 Hz
PC signal (HDMI)
No. Designation Resolution fh [kHz] fv [Hz]
dot CLK
[MHz]
Total No.
of Dots
[dot]
Total No.
of Lines
[line]
No. of
Effective
Dots [dot]
1 VGA 60 640×480 31,500 60,000 25,200 800 525 640 480
2 VGA 59.94 640×480 31,469 59,940 25,175 800 525 640 480
Indicator Display on the Main Unit
Meaning of the lighting figures
.
Operation mode display
Displays using the different colors and solid/blinking light of the “STANDBY/ON” indicator.
No. of
Effective
Lines
[line]
.
Estimated timing for lamp replacement
Displays using the solid/blinking light of the “LAMP” indicator. The “STANDBY/ON” indicator, which shows the operating mode of the unit, is displayed simultaneously as described above.
Others
.
62
Warning display
LAMP WARNING
STANDBY/ON
(Red)(*)Mode
Display
LAMP WARNING
STANDBY/ON
Blinking
Simultaneously
(Red)
(Orange)
Mode
Display
LAMP WARNING
STANDBY/ON
(Red)
(Orange)
Mode
Display
You can tell the details of a warning from the (repeated) displays of the “WARNING” and “LAMP” indicators. The “STANDBY/ON” indicator, which shows the operating mode of the unit, is displayed simultaneously as described above.
The Warning mode is activated once the message is displayed. Projection is interrupted, and the cooling fan is turned on for about 120 seconds.
The power cannot be turned on again while cooling is in progress. Check the following after cooling is complete.
Indicator Status (Solid/Blinking)
Blinking
Frequency
Description Check and Countermeasure
x1 Abnormality in the power supply0Check that nothing is blocking
x2 Cooling fan stopped abnormally
x3 Internal temperature is
abnormally high
x4 External temperature is too high
.
x5 Abnormal circuit operation
the air inlets.
0
Check that the external temperature is normal.
Countermeasure: Leave the unit unoperated until it cools down. After that, turn on the power again.
x1 Abnormal circuit operation
x2
x3
x4 Abnormal operation of the
automatic lens cover
.
0
Check that nothing is blocking the auto lens cover.
Countermeasure: Turn on the power again.
x1 Lamp does not light up and unit
is unable to project
x2 Lamp goes out during projection
x3 Lamp cover is removed
0
Check that the lamp unit and lamp cover are correctly installed.
Countermeasure: Turn on the power again.
.
If the Warning mode is activated again, wait for the cooling fan to stop, followed by pulling out the power plug from the outlet. Request for repair at your authorized dealer or a nearby service center.
(*) If the scheduled time for lamp replacement is exceeded, the indicator may light up.
Others
63
Dimensions
5
472
455
Lens
Ø60
24
103.5
178.5
227.5
Lens Center
33759
91 290
Lens
92110
32 110
Lamp Cover
(Unit: mm)
Top Surface
.
Front
Bottom Surface
.
Rear Surface
Others
64
.
.
0
The dimensions are identical for all the models.
Index
Accessories ......................................................... 11
A
Advanced Setting for Image Quality ..................... 30
Projection Screen Adjustment ............................. 34
Adjustment and Setting by the Menu ................... 26
Adjustment of the Image Quality .......................... 28
Advanced Menu ................................................... 30
Aperture ............................................................... 31
Back Color ........................................................... 40
B
Basic Setting for Image Quality ............................ 28
Brightness ............................................................ 28
C.M.D (Clear Motion Drive) ................................. 31
C
Ceiling Mount ....................................................... 19
Cleaning and Replacing the Filter ........................ 51
Clear Motion Drive ............................................... 31
Color Density ....................................................... 28
Color Management .............................................. 30
Color Shade ......................................................... 28
Color Space ......................................................... 32
Color Temperature ............................................... 29
Communication Terminal ..................................... 41
Connection .......................................................... 21
Contrast ............................................................... 28
Controls and Features ......................................... 12
Input terminals ..................................................... 14
Installation Method .............................................. 17
Lamp ................................................................... 11
L
Lamp Power ......................................................... 31
Lamp Time ........................................................... 42
Lens ..................................................................... 12
Lens Control ........................................................ 34
Lens sheet ........................................................... 12
Lens Shift ............................................................. 34
Line Display ......................................................... 40
Logo Display ........................................................ 40
Menu Display ....................................................... 40
M
Menu Items .......................................................... 26
Menu Position ...................................................... 40
Network ............................................................... 41
N
Off Timer .............................................................. 41
O
Optional Accessories ........................................... 11
PIC. ADJ. ............................................................. 28
P
Picture Mode ....................................................... 28
Precautions during Installation ............................. 17
Projection Distance .............................................. 60
Dimensions .......................................................... 64
D
Display Position ................................................... 32
External Control ................................................... 55
E
Filter Product no. ................................................. 51
F
Filter Replacement ............................................... 51
Focus ................................................................... 34
Frame Interpolation .............................................. 31
GAMMA ............................................................... 29
G
Gamma Adjustment ............................................. 29
HDMI Input Level ................................................. 32
H
HDMI Input Link ................................................... 32
HDMI Input Terminal ............................................ 21
HIDE .................................................................... 24
High Altitude Mode .............................................. 41
Indicator Display .................................................. 62
I
Input Resolution ............................................. 42, 62
Input Signal .................................................... 42, 62
Remote Control ................................................... 15
R
Replacing the Lamp ............................................. 43
Resetting the Lamp .............................................. 41
RS-232C .............................................................. 22
Screen Mask ........................................................ 33
S
Screen Size and Projection Distance ................... 60
Sharpness ........................................................... 30
Shift ..................................................................... 34
Signal Display ...................................................... 42
Software Ver. ....................................................... 42
Specifications ...................................................... 59
Troubleshooting ................................................... 52
T
Viewing Videos .................................................... 24
V
When the following messages appear... .............. 54
W
Zoom ................................................................... 34
Z
Others
65
DLA-VS2200ZG
DLA-VS2200G
D-ILA PROJECTOR
.
.
© 2013 JVCKENWOOD Corporation 0413SIB-SW-X
Loading...