JVC DLA-SH4K User Manual

PROJECTOR

DLA-SH4K

Getting Started Setup

INSTRUCTIONS

Operation and

Settings

Thank you for purchasing this JVC product.

Please study this instruction manual carefully before
starting to operate the unit, in order to use the unit correctly.
We take no responsibility for any problems resulting from
misuse of this unit by operating this equipment other than
instructed in this manual.

Others

For Customer use :

Enter below the serial No. which is
located on the bottom side of the
cabinet. Retain this information for
future reference.

Model No. DLA-SH4K

Serial No.

LCT2370-001B

Getting Started

Safety Precautions

IMPORTANT INFORMATION

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

WARNING:

THIS APPARATUS MUST BE EARTHED.

CAUTION:

To reduce the risk of electric shock, do not remove
cover. Refer servicing to qualified service personnel.

This projector is equipped with a 3-blade grounding type
plug to satisfy FCC rule. If you are unable to insert the
plug into the outlet, contact your electrician.

FCC INFORMATION (U.S.A. only)

CAUTION:

Changes or modification not approved by JVC could
void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own expense.

MACHINE NOISE INFORMATION (Germany only)

Changes Machine Noise Information Ordinance 3.
GSGV, January 18, 1991: The sound pressure level
at the operator position is equal or less than 70 dB
(A) according to ISO 7779.

About the installation place

Do not install the projector in a place that cannot
support its weight securely.

If the installation place is not sturdy enough, the
projector could fall or overturn, possibly causing
personal injury.

IMPORTANT SAFEGUARDS

Electrical energy can perform many useful functions.
This unit has been engineered and manufactured to
assure your personal safety. But IMPROPER USE CAN
RESULT IN POTENTIAL ELECTRICAL SHOCK OR
FIRE HAZARD. In order not to defeat the safeguards
incorporated into this product, observe the following
basic rules for its installation, use and service. Please
read these Important Safeguards carefully before use.

- All the safety and operating instructions should be

read before the product is operated.

- The safety and operating instructions should be

retained for future reference.

- All warnings on the product and in the operating

instructions should be adhered to.

- All operating instructions should be followed.

- Place the projector near a wall outlet where the plug

can be easily unplugged.

- Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.

- Do not use attachments not recommended by the

product manufacturer as they may be hazardous.

- Do not use this product near water. Do not use

immediately after moving from a low temperature to
high temperature, as this causes condensation, which
may result in fire, electric shock, or other hazards.

- Do not place this product on an unstable cart, stand,

or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product.
The product should be mounted according to the
manufacturer’s instructions, and should use a mount
recommended by the manufacturer.

- When the product is used on a cart,

care should be taken to avoid quick
stops, excessive force, and uneven
surfaces which may cause the
product and cart to overturn,
damaging equipment or causing
possible injury to the operator.

- Slots and openings in the cabinet

are provided for ventilation. These ensure reliable
operation of the product and protect it from
overheating. These openings must not be blocked or
covered. (The openings should never be blocked by
placing the product on bed, sofa, rug, or similar
surface. It should not be placed in a built-in installation
such as a bookcase or rack unless proper ventilation
is provided and the manufacturer’s instructions have
been adhered to.) For proper ventilation, separate the
product from other equipment, which may prevent
ventilation and keep a distance (See page 11).

- This product should be operated only with the type of

power source indicated on the label. If you are not
sure of the type of power supply to your home, consult
your product dealer or local power company.

- This product is equipped with a three-wire plug. This

plug will fit only into a grounded power outlet. If you
are unable to insert the plug into the outlet, contact
your electrician to install the proper outlet. Do not
defeat the safety purpose of the grounded plug.

2

- Power-supply cords should be routed so that they are

not likely to be walked on or pinched by items placed
upon or against them. Pay particular attention to cords
at doors, plugs, receptacles, and the point where they
exit from the product.

- For added protection of this product during a lightning

storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent
damage to the product due to lightning and power line
surges.

- Do not overload wall outlets, extension cords, or

convenience receptacles on other equipment as this
can result in a risk of fire or electric shock.

- Never push objects of any kind into this product

through openings as they may touch dangerous
voltage points or short out parts that could result in a
fire or electric shock. Never spill liquid of any kind on
the product.

- Do not attempt to service this product yourself as

opening or removing covers may expose you to
dangerous voltages and other hazards. Refer all
service to qualified service personnel.

-

Unplug this product from the wall outlet and refer
service to qualified service personnel under the
following conditions:

a) When the power supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen on the

product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the Operation Manual, as an improper

adjustment of controls may result in damage and will often

require extensive work by a qualified technician to restore

the product to normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in

performance - this indicates a need for service.

- When replacement parts are required, be sure the

service technician has used replacement parts
specified by the manufacturer or with same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.

-

Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in proper
operating condition.

- The product should be placed more than one foot

away from heat sources such as radiators, heat
registers, stoves, and other products (including
amplifiers) that produce heat.

- When connecting other products such as VCR’s, and

DVD players, you should turn off the power of this
product for protection against electric shock.

- Do not place combustibles behind the cooling fan. For

example, cloth, paper, matches, aerosol cans or gas
lighters that present special hazards when over
heated.

- Do not look into the projection lens while the

illumination lamp is turned on. Exposure of your eyes
to the strong light can result in impaired eyesight.

- Do not look into the inside of this unit through vents

(ventilation holes), etc. Do not look at the illumination
lamp directly by opening the cabinet while the
illumination lamp is turned on. The illumination lamp
also contains ultraviolet rays and the light is so
powerful that your eyesight can be impaired.

- Do not drop, hit, or damage the light-source lamp

(lamp unit) in any way. It may cause the light-source
lamp to break and lead to injuries. Do not use a
damaged light source lamp. If the light-source lamp is
broken, ask your dealer to repair it. Fragments from a
broken light-source lamp may cause injuries.

- The light-source lamp used in this projector is a high

pressure lamp. Be careful when disposing of the
lightsource lamp. If anything is unclear, please consult
your dealer.

- Do not ceiling-mount the projector to a place which

tends to vibrate; otherwise, the attaching fixture of the
projector could be broken by the vibration, possibly
causing it to fall or overturn, which could lead to
personal injury.

- Use only the accessory cord designed for this product

to prevent shock.

*DO NOT allow any unqualified person to

install the unit.

Be sure to ask your dealer to install the unit (e.g.
attaching it to the ceiling) since special technical
knowledge and skills are required for installation. If
installation is performed by an unqualified person, it
may cause personal injury or electrical shock.

3

Getting Started

Safety Precautions (Cont’d)

POWER CONNECTION

The power supply voltage rating of this product is
AC110 V – 120 V, AC200 V – 240 V, the power cord
attached conforms to the following power supply
voltage. Use only the power cord designated by our
dealer to ensure Safety and EMC.

When it is used by other power supply voltage,
power cable must be changed.

Ensure that the power cable used for the projector is
the correct type for the AC outlet in your country.
Consult your product dealer.

Power cord

For European continent countries:

AC200 V – 240 V

(3.3 m)

IMPORTANT:

The wires in the mains lead on this product are
colored in accordance with the following cord:
Green-and-yellow : Earth
Blue : Neutral
Brown : Live
As these colors may not correspond with the colored
making identifying the terminals in your plug,
proceed as follows:
The wire which is colored green-and-yellow must be
connected to the terminal which is marked M with
the letter E or the safety earth or colored green or
green-and-yellow.
The wire which is colored blue must be connected to
the terminal which is marked with the letter N or
colored black.
The wire which is colored brown must be connected
to the terminal which is marked with the letter L or
colored red.

Power cord

Power supply voltage:

AC110 V – 120 V

(3.3 m)

WARNING:
Do not cut off the main plug from this

equipment.

If the plug fitted is not suitable for the power points in
your home or the cable is too short to reach a power
point, then obtain an appropriate safety approved
extension lead or adapter or consult your dealer.
If nonetheless the mains plug is cut off, dispose of
the plug immediately, to avoid a possible shock
hazard by inadvertent connection to the main
supply. If a new main plug has to be fitted, then
follow the instruction given below.

WARNING:

THIS APPARATUS MUST BE EARTHED.

4

EMC Supplement

-

This equipment is in conformity with the provisions and protection requirements of the corresponding European Directives.
This equipment is designed for professional projector appliances and can be used in the following environments.

● Controlled EMC environment (for example purpose built broadcasting or recording studio), and the rural outdoors

environment (far away from railways, transmitters, overhead power lines, etc).

In order to keep the best performance and furthermore for electromagnetic compatibility we recommend to use the
cables not exceeding the following length:

Cables Length
Power cord Power supply cord 3.3 m
DVI (X4) Cable Shielded cable 5.0 m
USB Cable Shielded cable 2.0 m
LAN Cable Shielded cable 2.0 m
RS-232C Cable Shielded cable 1.6 m

● The inrush current of this apparatus is 9.705 amperes.

WARNING
This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.
In case where the strong electromagnetic waves or magnetism are near the signal

cable, the picture will contain noise. In such cases, please keep the cable away from
the sources of the disturbance.

Dear Customer,

This apparatus is in conformance with the valid European directives and standards regarding electromagnetic
compatibility and electrical safety.

European representative of Victor Company of Japan, Limited is:
JVC Technology Centre Europe GmbH
Company name changed in:
JVC Technical Services Europe GmbH
Postfach 10 05 52
61145 Friedberg
Germany

5

Getting Started

Contents

Getting Started

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Check the Accessories/Optional Accessories . . . . . . . 6

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . 6

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

How to Read this Manual . . . . . . . . . . . . . . . . . . . . . . 7

Precautions During Use . . . . . . . . . . . . . . . . . . . . . . . 8

Names and Functions of Parts . . . . . . . . . . . . . . . . . . 9

Setup

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Minimum Space Required . . . . . . . . . . . . . . . . . . . 11

Projector Installation . . . . . . . . . . . . . . . . . . . . . . . 12

Installing the Projector and Screen . . . . . . . . . . . . 12

Screen Size and Projection Distance . . . . . . . . . . 15

Connecting Video Signals of the Computer . . . . . . . 16

Connection During Single-Screen Mode Display . . .16

Connection During Two-Screen/

Four-Screen Mode Display . . . . . . . . . . . . . . . . . . 18

Connection Using a LAN Cable . . . . . . . . . . . . . . . . . 20

Connection Example . . . . . . . . . . . . . . . . . . . . . . . 20

Specifications of PC for Controlling this Projector . . . 20

Configuring the Network Settings . . . . . . . . . . . . . . . 20

Using the Mail Delivery Feature . . . . . . . . . . . . . . . . 21

Connection Example . . . . . . . . . . . . . . . . . . . . . . . 21

Others

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Cleaning and Replacing the Filter . . . . . . . . . . . . . 36

Routine Servicing . . . . . . . . . . . . . . . . . . . . . . . . . 37

Replacement of Light Source Lamp . . . . . . . . . . . 37

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

What to do when these messages are displayed . . . 40

Warnings Using Indicators . . . . . . . . . . . . . . . . . . . . 41

Latest Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Dimensional Outline Drawing . . . . . . . . . . . . . . . . . . 45

Check the Accessories/ Optional Accessories

For the US market (x1)

Power Cord
For USA (3.3 m)

For the EU market (x1)

Power Cord
For European

continent countries
(3.3 m)

Operation and Settings

Projecting Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Useful Features During Projection . . . . . . . . . . . . . 23

Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Setting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Convergence Menu . . . . . . . . . . . . . . . . . . . . . . . . 28

Lens Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Option Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Network Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Mail Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

RS-232C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Communication Specifications . . . . . . . . . . . . . . . . 34

Command Format . . . . . . . . . . . . . . . . . . . . . . . . . 34

6

● Other items include the instruction manual, and other

printed materials.

Optional Accessories

● Replacement filter/sponge (front)

LC43009-001A (Filter)
LC43030-001A (Sponge)

● Replacement filter/sponge (right side)

LC43009-002A (Filter)
LC43030-002A (Sponge)

Features

Ultra-high resolution, high contrast,
and high quality projector

 Ultra-high resolution of 40962400

This projector comes with a newly developed 1.27" and
40962400 pixel D-ILA (Direct-drive Image Light
Amplifier) device, and achieves an ultra-high resolution of

9.83 million pixels, which is four times that of full HD.

 High contract ratio of 10,000:1

A high contrast ratio of 10,000:1 (native) is achieved
through combining the D-ILA device with WireGrid
(inorganic reflective polarizing plate) that is employed in
the new optical engine.

High flexible installation

● The Email feature enables you to send reports on the

lamp replacement timing or error messages to a
remote location.



Comes with various built-in test patterns (six
types including Cross Hatch, Color Bars, etc.)

Enables image adjustment without the need of external
signal sources.

Features that enable flexible
display and expression

 Supports multi screens (single screen, two-

screen, and four-screen modes)



Comes with three types of built-in gamma tables.
Enables configuration of gradation expression
settings according to the video image

How to Read this Manual

 Design is compact and light, and enables

stacking

● This product is about 65 % the size of existing JVC

projectors of the same class, and its weight is as light
as 55 kg (excluding lens).

● Stackable design enhances installation for special

applications (e.g. 3D).

 Vertical/Horizontal lens shift

This projector enables not only vertical (±50 %), but also
horizontal (±25 %) lens shift, which enables a larger
degree of flexibility in the layout.

 Inclined installation

This product can be installed at a tilt angle of up to ±90°,
which provides greater flexibility in the location of the
projection screen.

 Low power consumption

This product helps to save power with a consumption of
not more than 1.5 kW.

User-friendly interface and high
operability

How to Read this Manual

 Symbols used in this manual

CAUTION : Describes precautions to note when

operating this product.

NOTE : Describes reference information, such

as functions and restrictions during use.

A

 Content of this manual

● Personal computers or computers are expressed as

computers or PCs in this manual.

● Contents of this manual are the copyright of JVC. All

rights reserved. Unauthorized reproduction and
duplication of this manual, in whole or in part,
without the permission of JVC is strictly prohibited.

● The names of other companies’ products that

appear in this manual are the trademark or
registered trademark of the respective companies.
Symbols such as ™, , and  are omitted in this
manual.

● Designs, specifications, and other details described

in this manual may be modified for improvement
without prior notice.

: Indicates the page or section to refer to.



Equipped with DVI (Dual-Link)4 input terminals

 Network-supported

● In addition to the conventional RS-232C, it also

provide support for connection using Ethernet.
You can make adjustments or configure settings from
the web browser on the PC without having to install
any special software.

● Network connection enables you to make perform

adjustment or configure settings for multiple projectors
using a single PC.

7

Getting Started

Precautions During Use

Burning-in of D-ILA Device

oDo not allow the same still picture to be

projected for a long time or an abnormally
bright video image to be projected

Do not project still images with a high brightness or
high contrast on the screen for a long time. This
video image could be burnt into the D-ILA device.

Pay special attention when projecting video games and
computer program images.
Motion images such as normal video playback images
do not pose the burning-in problem.

Viewing Conditions (Brightness
of Room)

oBrightness of the room

Avoid direct exposure of screen to direct sunlight
and lights such as by using a curtain. Images can be
well projected by darkening the brightness of the
room.

Maintenance Procedures

oClean dirt on the cabinet

with a soft cloth. In case of heavy soiling, soak a
cloth in neutral detergent diluted with water, wring
dry and wipe, followed by wiping again using a dry
cloth.

oPay attention to the following to prevent the

cabinet from deteriorating in condition,
getting damaged, or the paint from coming
off.

● Do not wipe with a stiff cloth

● Do not wipe with force

● Do not wipe with thinner or benzene

● Do not spray volatile chemicals like insecticide

● Do not allow prolonged contact with rubber or plastic

products

oClean dirt on the lens

using commercial blowers or lens cleaning papers
(for cleaning glasses and cameras).

Do not use fluid-type cleaning agents. This may lead to
peeling of the surface coating film.
Lens surface is fragile. Avoid rubbing it hard or
knocking it.

oDo not view screen for prolonged hours

Looking at the screen continually for a prolonged
time is tiring to the eyes. Allow your eyes to rest at
intervals.

oDo not use this unit when image flickers

due to installation conditions and environment. This
may cause your eyesight to deteriorate.

Environment of Use

oDo not use this projector in rooms with

cigarette smoke or oily smoke

Do not use this projector in rooms with cigarette
smoke or oily smoke. This may cause the unit to
malfunction.

oWhen mounting this projector to the ceiling

Check the temperature around the projector unit.
When a heater is in use, the ceiling may reach a
temperature higher than anticipated, hence leading
to malfunction of the unit.

Gauging replacement time of components

This product comes with replacement components required for maintaining the functions of this product, such as
optical components, cooling fan and filters. The timing for replacing components varies considerably according to
the frequency and environment of use. For details on replacement of components (except filters), please consult
any nearby JVC servicing center.

8

Names and Functions of Parts

B C D E

Front/Right Side

A

Intake air

Intake air

A Air Inlet/Filter

The air inlets absorb air to cool the interior of the
projector. A filter is mounted inside the projector to
remove dirt in the air that enters through the inlets. Clean
the filter regularly. (A Page 36)

CAUTION:

● Do not block the air inlets with papers, cloth, or soft

cushions. Doing so may cause heat to trap inside the
projector and result in fire or malfunction.

B Lens Cap

Fit the cap on the lens when this projector is not in use to
prevent the lens from becoming dirty.

CAUTION:

● Do not project images with the lens cap attached. The

lens cap may be deformed due to the heat, or the
projector may malfunction.

C Lens

This projector makes use of a x1.22 power zoom lens.
Remove the lens cap before projection.

D Adjustable Feet (x 4)

Adjust the feet until the projector is level. The adjustable
range is 20 mm for each. (A Page 12)

E Air Inlet/Filter

The air inlets absorb air to cool the interior of the
projector. A filter is mounted inside the projector to
remove dirt in the air that enters through the inlets. Clean
the filter regularly. (A Page 36)

9

Getting Started

FG H IJ

FG H IJ

Names and Functions of Parts
(Cont’d)

Rear

DVI 1

DVI 2

CONTROL

Q

Q
P

P
O

O

USB

DVI 3

LAN

RS-232C

STANDBY/ON

OPERATE I/B

LAMP

DVI 4

WARNING

Exhaust air

F [DVI 1 to 4] Terminal

This is an input terminal for video signals. Connect it to
the video output terminal of the computer.
(A Page 17, 19)

G

Vent Hole

Warm air exits from the hole after cooling the projector.

CAUTION:

● Do not block the vent holes with papers, cloth, or soft

cushions. Doing so may cause heat to trap inside the
projector and result in fire or malfunction.

H Vent Hole (For Lamp)

Warm air exits from the hole after cooling the lamp.

I Main Power Supply Switch

Use this to turn ON/OFF the main power supply of the
projector unit.

J AC Power Input Terminal

Connect the supplied cord to this terminal.

K [STANDBY/ON] Indicator

Lit (Red) : When in the standby mode.

Lit (Green) : When power is supplied.

Blinking (Red) : When in the cooling (cool down)

Blinking (Green) : When the projected image is

mode. (A Page 23)

temporarily hidden. (A Page 23)

KLMN

KLMN

L [LAMP] Indicator

This indicator lights up when the lamp time exceeds 1400
hours.

NOTE:

● For details on indicator displays during warnings, refer

to “Warnings Using Indicators”. (A Page 41)

● A lamp life message appears when the lamp time has

exceeded 1500 hours. (A Page 40)

M [WARNING] Indicator

This indicator lights up when abnormality occurs on this
projector. For details, refer to “Warnings Using
Indicators”. (A Page 41)

N [OPERATE I/B] Button

Pressing this button for one second or longer when in the
standby mode (main power supply is ON) turns on the
power of the projector unit. Pressing it for one second or
longer when the power is ON switches the projector to
the standby mode.

O [RS-232C] Terminal

This is the RS-232C interface-specific terminal. This
projector can be controlled by connecting it to a computer
using a RS-232C cable.

P [LAN] Terminal

Enables control of this projector using a computer that is
connected to the network.

NOTE:

● For details on indicator displays during warnings, refer
to “Warnings Using Indicators”. (A Page 41)

10

Q [USB] Terminal

Enables control of this projector by connecting it to a
computer.

Setup

Installation

Please read the following carefully when installing this unit.

Minimum Space Required

Do not use a cover that may enclose this unit or block the air inlets/vent holes. Allow sufficient space around this unit.
When this unit is enclosed in a space with dimensions as indicated below, ventilate accordingly so that the internal and
external temperatures are the same.

 When using one set of projector

300 mm

600 mm600 mm

 When using two sets of projectors side by side

300 mm

600 mm

640 mm

 When the projector is suspended

300 mm and
above

300 mm

600 mm

300 mm

600 mm

1,300 mm

NOTE:

● To prevent the projector from falling or toppling, it is

recommended that the holder be fastened to the unit
using bolts.

● To mount the projector to the ceiling, mount a special

shelf to the ceiling, followed by installing the unit on
the shelf. For safety and maintenance purposes,
equipment that eases adjustment to a suitable height
for maintenance is required.

CAUTION:

●

Special expertise and techniques are required for
mounting this unit. Be sure to ask your dealer or a
specialist to perform mounting.

11

Setup

Installation (Cont’d)

Projector Installation

You can install this projector between 90.
Images will be properly displayed if the horizontal angle
is between the range of 5.

90

90

Installing the Projector and Screen

It is recommended that this projector be installed at right
angle to the screen.
You can shift the projection screen position vertically
between 0 % to ±50 %, and horizontally between 0 % to
±25 %. (Lens shift feature)

 When shift amount in the upward direction is

+50 %

Install the projector such that the lower end of the
projection screen is at the same height as the center of
the lens.

Screen

90 90 90

Center Line of Lens

55

CAUTION:

●

To ceiling-mount this unit, special expertise and skills are
necessary. Make to sure request the authorized dealer or
specialized work contractors for installation.

● The projector cannot be installed upside down.

 Adjusting the Inclination

Adjust the horizontal angle of the projector.
Lift the projector and turn the nut of the adjustable foot
with a spanner in the direction indicated by the arrow to
extend or retract the foot. The adjustable range is 20 mm.

 When shift amount in the upward/downward

direction is 0 %

Install the projector such that the center of the projection
screen is at the same height as the center of the lens.

Screen

90 90 90

Center Line of Lens



When shift amount in the downward direction is
–50 %

Install the projector such that the upper end of the
projection screen is at the same height as the center of
the lens.

Extend Retract

12

Screen

Center Line of Lens

90 90 90

 When shift amount in the right direction is

+25 %

Install the projector such that the center of the lens is
aligned with the 1/4 position from the left edge of the
screen.

 Movable Range of Projected Image

50 %

 When shift amount in the left/right direction

is 0 %

Install the projector such that the center of the lens is
aligned with the center of the screen.

25 %

50 %

25 %

NOTE:

● When using the lens shift feature, do not exceed the

range (shift amount) as shown above. If the shift
amount exceeds the range as shown, shadows will
appear on the projected image.

 When light passes through the glass of

projection booth



When shift amount in the left direction is –25 %

Install the projector such that the center of the lens is
aligned with the 1/4 position from the right edge of the
screen.

NOTE:

● When light passes through the glass, the quantity of

light decreases. Make sure that the glass of the
projection booth is not more than one piece.

● Do not use glass if possible.

● When projecting light on an inclined glass surface,

adjust the glass angle as well as installation angle of
this unit accordingly to prevent impact on the image
due to diffuse reflection.

13

Setup

Installation (Cont’d)

Installing the Projector and
Screen (Cont’d)

 Overlaying projected images

 Projecting images by stacking projectors

The lens shift feature enables you to use up to three
stacked projectors at the same time.
Stacking projectors enhances the brightness level, and
helps to project images that are sufficiently bright even
when the venue is relatively big or bright.

 Projecting images by arranging projectors

side by side

The lens shift feature enables you to use up to two
projectors that are arranged side by side.
Arranging two projectors side by side enhances the
brightness level, and helps to project images that are
sufficiently bright even when the venue is relatively big or
bright.
When projecting images by arranging the projectors side
by side, adjust the shift amount of both projectors
accordingly to superimpose the images.

CAUTION:

●

When the projectors are stacked together during use,
ensure that the installation site is sufficiently strong and
there is proper air cooling around the projectors.

Take the necessary measures to prevent the
projectors from toppling or falling off so as to ensure
safety during emergency situations, such as
earthquakes, and to prevent accidents from occurring.
For details, please consult your authorized dealer.

NOTE:

● When using the projectors by arranging them side by

side, ensure that the installation site is sufficiently
strong and there is proper air cooling around the
projectors. For details, please consult your authorized
dealer. (A Page 11)

14

Screen Size and Projection
Distance

Adjust the distance from the lens to the screen to achieve your desired screen size.
This projector uses a 1.22x power zoom lens for projection.

Projection Screen Size

(Diagonal Length)

80" (Approx. 2.03 m) 1.75 m 3.19 m 2.58 m

90" (Approx. 2.29 m) 1.97 m 3.60 m 2.91 m

100" (Approx. 2.54 m) 2.19 m 4.01 m 3.25 m

110" (Approx. 2.79 m) 2.41 m 4.42 m 3.58 m

120" (Approx. 3.05 m) 2.63 m 4.83 m 3.91 m

130" (Approx. 3.30 m) 2.85 m 5.24 m 4.25 m

140" (Approx. 3.56 m) 3.07 m 5.65 m 4.58 m

150" (Approx.3.81 m) 3.29 m 6.06 m 4.91 m

160" (Approx. 4.06 m) 3.51 m 6.46 m 5.25 m

170" (Approx. 4.32 m) 3.73 m 6.87 m 5.58 m

180" (Approx. 4.57 m) 3.94 m 7.28 m 5.91 m

190" (Approx. 4.83 m) 4.16 m 7.69 m 6.24 m

200" (Approx. 5.08 m) 4.38 m 8.10 m 6.58 m

210" (Approx. 5.33 m) 4.60 m 8.51 m 6.91 m

220" (Approx. 5.59m) 4.82 m 8.92 m 7.24 m

230" (Approx. 5.84 m) 5.04 m 9.33 m 7.58 m

240" (Approx. 6.10 m) 5.26 m 9.74 m 7.91 m

250" (Approx. 6.35 m) 5.48 m 10.15 m 8.24 m

260" (Approx. 6.60 m) 5.70 m 10.55 m 8.58 m

270" (Approx. 6.86 m) 5.92 m 10.96 m 8.91 m

280" (Approx. 7.11 m) 6.14 m 11.37 m 9.24 m

290" (Approx. 7.37 m) 6.36 m 11.78 m 9.57 m

300" (Approx. 7.62 m) 6.57 m 12.19 m 9.91 m

Image Width

Tele End Wide End

Projection distance

NOTE:

● The distance indicated in the table is an estimated value when an image with a resolution of 40962400 is projected.

Please use them as reference during installation.

15