JVC DLA-RS6710 User Manual

.

INPUT

PHOTO

http://manual3.jvckenwood.com/projector/mobile/global/

The Mobile User Guide can be viewed on mobile internet devices including
smartphones and tablets.

Mobile User Guide

Pour utilisation par le client :

Entrerci-dessous le N°de série qui
est situé sous le boîtier. Garder
cetteinformation comme référence
pour le futur.

Instrucción para el cliente :

Introduzca a continuación el nº de
serie que aparece en la parte
inferior lateral de la caja. Conserve
esta información como referencia
para uso ulterior.

For Customer use :

Enter below the serial No. which is
located on the side of the cabinet.
Retain this information for future
reference.

DLA-RS6710U/
DLA-RS4910U

Model No.

Serial No.

DLA-RS6710U/
DLA-RS4910U

N° de modèle

N° de série

DLA-RS6710U/
DLA-RS4910U

Modelo Nº

Nº de serie

D-ILA
PROJECTOR

DLA-RS6710
DLA-RS4910

ENGLISH

FRANÇAIS

ESPAÑOL/CASTELLANO

Getting Started Set up Operate Adjust/Set Maintenance Troubleshooting Others

INSTRUCTIONS

.

.

.

Not suitable for household room illumination.

PC027183799-1

Safety Precautions

⹣晼㯡婌♟㒷

IMPORTANT INFORMATION

This product has a High Intensity
Dis-charge (HID) lamp that contains
mercury.
Disposal of these materials may be
regulated in your community due to
environmental considerations. For
disposal or recycling information,
please contact your local authorities or
for USA, the Electronic Industries
Alliance: http://www.eiae.org.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.

MACHINE NOISE INFORMATION
(Germany only)

Changes Machine Noise Information Ordinance 3.
GSGV, January 18, 1991: The sound pressure level
at the operator position is equal or less than 20 dB
(A) according to ISO 7779.

FCC INFORMATION (U.S.A. only)
CAUTION:

Changes or modification not approved by JVC could
void the user’s authority to operate the equipment.

About the installation place

Do not install the projector in a place that cannot
support its weight securely.
If the installation place is not sturdy enough, the
projector could fall or overturn, possibly causing
personal injury.

Reorient or relocate the receiving antenna.
Increase the separation between the equipment

and receiver.

Consult the dealer or an experienced radio/TV
technician for help.

Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.

NOTE:

This equipment has been tested and found to comply
with the limits for Class B digital devices, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protec tion against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruc tions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encourage to try to
correct the interference by one or more of the
following measures:

WARNING:

THIS APPARATUS MUST BE EARTHED.

CAUTION:

For the customers in Taiwan only

To reduce the risk of electric shock, do not remove
cover. Refer servicing to qualified service personnel.

This projector is equipped with a 3-blade grounding
type plug to satisfy FCC rule. If you are unable to
insert the plug into the outlet, contact your electrician.

Declaration of Conformity

Model Number: DLA-RS6710U/DLA-RS4910U
Trade Name: JVC
Responsible party: JVC AMERICAS CORP.
Address: 1700 Valley Road Wayne, N. J. 07470
Telephone Number: 973-317-5000
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.

Getting Started

.

2

150 mm and above

150 mm
and above

300 mm
and above

200 mm
and above

300 mm
and above

PORTABLE CART WARNING
(symbol provided by RETAC)

S3126A

Front

-

-

-

-

-

-

-

-

-

-

-

-

-

IMPORTANT SAFEGUARDS

Electrical energy can perform many useful functions.
This unit has been engineered and manufactured to
assure your personal safety. But IMPROPER USE
CAN RESULT IN POTENTIAL ELECTRICAL
SHOCK OR FIRE HAZARD. In order not to defeat
the safeguards incorporated into this product,
observe the following basic rules for its installation,
use and service. Please read these Important
Safeguards carefully before use.

All the safety and operating instructions should be read
before the product is operated.
The safety and operating instructions should be retained for
future reference.
All warnings on the product and in the operating
instructions should be adhered to.
All operating instructions should be followed.
Place the projector near a wall outlet where the plug can be
easily unplugged.
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
Do not use attachments not recommended by the product
manufacturer as they may be hazardous.
Do not use this product near water. Do not use immediately
after moving from a low temperature to high temperature,
as this causes condensation, which may result in fire,
electric shock, or other hazards.
Do not place this product on an unstable cart, stand, or
table. The product may fall, causing serious injury to a child
or adult, and serious damage to the product. The product
should be mounted according to the manufacturer’s
instructions, and should use a mount recommended by the
manufacturer.
When the product is used on a cart,
care should be taken to avoid quick
stops, excessive force, and uneven
surfaces which may cause the product
and cart to overturn, damaging
equipment or causing possible injury to
the operator.
Slots and openings in the cabinet are provided for
ventilation. These ensure reliable operation of the product
and protect it from overheating. These openings must not
be blocked or covered. (The openings should never be
blocked by placing the product on bed, sofa, rug, or similar
surface. It should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided
and the manufacturer’s instructions have been adhered to.)
To allow better heat dissipation, keep a clearance between
this unit and its surrounding as shown below. When this unit
is enclosed in a space of dimensions as shown below, use
an air-conditioner so that the internal and external
temperatures are the same. Overheating can cause
damage.

-

-

-

-

-

-

-

-

-

-

-

-

a)
b)

c)
d)

e)

f)

When the power supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen on the
product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the
operating instructions. Adjust only those controls that
are covered by the Operation Manual, as an improper
adjustment of controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to normal operation.
If the product has been dropped or damaged in any
way.
When the product exhibits a distinct change in
performance, this indicates a need for service.

When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or with same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
The product should be placed more than one foot away
from heat sources such as radiators, heat registers, stoves,
and other products (including amplifiers) that produce heat.
When connecting other products such as VCR’s, and DVD
players, you should turn off the power of this product for
protection against electric shock.

Power source indicated on the label. If you are not sure of
the type of power supply to your home, consult your
product dealer or local power company.
This product is equipped with a three-wire plug. This plug
will fit only into a grounded power outlet. If you are unable
to insert the plug into the outlet, contact your electrician to
install the proper outlet. Do not defeat the safety purpose of
the grounded plug.
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them. Pay particular attention to cords at doors,
plugs, receptacles, and the point where they exit from the
product.
For added protection of this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent damage to
the product due to lightning and power line surges.
Do not overload wall outlets, extension cords, or
convenience receptacles on other equipment as this can
result in a risk of fire or electric shock.
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltages
and other hazards. Refer all service to qualified service
personnel.
Unplug this product from the wall outlet and refer service to
qualified service personnel under the following conditions:

Getting Started

.

3

-

-

-

-

-

-

-

-

-

-

-

Do not place combustibles behind the cooling fan. For
example, cloth, paper, matches, aerosol cans or gas
lighters that present special hazards when over heated.
Do not look into the projection lens while the illumination
lamp is turned on. Exposure of your eyes to the strong light
can result in impaired eyesight.
Do not look into the inside of this unit through vents
(ventilation holes), etc. Do not look at the illumination lamp
directly by opening the cabinet while the illumination lamp is
turned on. The illumination lamp also contains ultraviolet
rays and the light is so powerful that your eyesight can be
impaired.
Do not drop, hit, or damage the light-source lamp (lamp
unit) in any way. It may cause the light-source lamp to
break and lead to injuries. Do not use a damaged light
source lamp. If the light-source lamp is broken, ask your
dealer to repair it. Fragments from a broken light-source
lamp may cause injuries.
The light-source lamp used in this projector is a high
pressure mercury lamp. Be careful when disposing of the
light-source lamp. If anything is unclear, please consult
your dealer.
Do not ceiling-mount the projector to a place which tends to
vibrate; otherwise, the attaching fixture of the projector
could be broken by the vibration, possibly causing it to fall
or overturn, which could lead to personal injury.
Use only the accessory cord designed for this product to
prevent shock.
For health reasons, please take a break of about 5-15
minutes every 30-60 minutes and let your eyes rest. Please
refrain from watching any 3D-images when you feel tired,
unwell or if you feel any other discomfort. Moreover, in case
you see a double image, please adjust the equipment and
software for proper display. Please stop using the unit if the
double image is still visible after adjustment.
Once every three years, please perform an internal test.
This unit is provided with replacement parts needed to
maintain its function (such as cooling fans). Estimated
replacement time of parts can vary greatly depending on
frequency of use and the respective environment. For
replacement, please consult your dealer, or the nearest
authorized JVC service center.
When fixing the unit to the ceiling, Please note that we do
not take any responsibility, even during the warranty period,
if the product is damaged due to use of metal fixtures used
for fixation to the ceiling other than our own or if the
installation environment of said metal fixtures is not
appropriate. If the unit is suspended from the ceiling during
use, please be careful in regard to the ambient temperature
of the unit. If you use a central heating, the temperature
close to the ceiling will be higher than normally expected.
Video images can burn into the electronic com ponent
parts. Please do not display screens with still images of
high brightness or high contrast, such as found in video
games and computer programs. Over a long period of time
it might stick to the picture element. There is no problem
with the playback of moving images, e.g. normal video
footage.

-

-

-

-

-

-

-

Video images can burn into the electronic com ponent
parts. Please do not display screens with still images of
high brightness or high contrast, such as found in video
games and computer programs. Over a long period of time
it might stick to the picture element. There is no problem
with the playback of moving images, e.g. normal video
footage.
Not using the unit for a long time can lead to malfunction.
Please power it on and let it run occasionally. Please avoid
using the unit in a room where cigarettes are smoked. It is
impos sible to clean optical component parts if they are
contaminated by nicotine or tar. This might lead to
performance degradation.
Please watch from a distance three times the height of the
projected image size. Persons with photosensitivity, any
kind of heart disease, or weak health should not use 3D
glasses.
Watching 3D-images might be cause of illness. If you feel
any change in your physical condition, please stop
watching immediately and consult a physician if necessary.
When watching 3D images, it is recommended to take
regular breaks. As the length and frequency of the required
breaks differ for every person, please judge according to
your own condition.
If your child watches while wearing 3D glasses, it should be
accompanied by its parents or an adult guardian. The adult
guardian should be careful to avoid situations where the
child’s eyes might become tired, as responses to tiredness
and discomfort, etc., are hard to detect, and it is possible
for the physical condition to deteriorate very quickly. As the
visual sense is not yet fully developed in children under the
age of 6, please consult a physician in regard to any
problem concerning 3D-images if necessary.
Note that when using the 3D feature, the video output may
appear different from the original video image due to image
conversion on the device.

* DO NOT allow any unqualified person to
install the unit.

Be sure to ask your dealer to install the unit
(e.g.attaching it to the ceiling) since special
technical knowledge and skills are required for
installation. If installation is performed by an
unqualified person, it may cause personal injury or
electrical shock.

Getting Started

.

4

Power cord

Power cord

For European continent
countries

For United Kingdom

Green-and-yellow
Blue
Brown

Fuse

: Earth
: Neutral
: Live

POWER CONNECTION

WARNING:

WARNING:

Do not cut off the main plug from this
equipment.

The power supply voltage rating of this product is
AC110V – AC240V. Use only the power cord
designated by our dealer to ensure Safety and EMC.
Ensure that the power cable used for the projector is
the correct type for the AC outlet in your country.
Consult your product dealer.

If the plug fitted is not suitable for the power points
in your home or the cable is too short to reach a
power point, then obtain an appropriate safety
approved extension lead or adapter or consult your
dealer. If nonetheless the mains plug is cut off,
dispose of the plug immediately, to avoid a possible
shock hazard by inadvertent connection to the main
supply. If a new main plug has to be fitted, then
follow the instruction given below.

Dear Customer,

This apparatus is in conformance with the valid European directives and standards regarding
electromagnetic compatibility and electrical safety.

European representative of JVC KENWOOD Corporation is:
JVC Technical Services Europe GmbH
Konrad-Adenauer-Allee 1-11
61118 Bad Vilbel
Germany

THIS APPARATUS MUST BE EARTHED.

IMPORTANT (Europe only):

The wires in the mains lead on this product are
colored Vert et jaune in accordance with the
following cord:

IMPORTANT (Europe only):

POWER CONNECTION
(United Kingdom only)

When replacing the fuse, be sure to use only a
correctly rated approved type, re-fit the fuse cover.

IF IN DOUBT —— CONSULT A COMPETENT
ELECTRICIAN.

Open the fuse compartment with the blade
screwdriver, and replace the fuse.
(* An example is shown in the illustration below.)

As these colors may not correspond with the
colored making identifying the terminals in your
plug, proceed as follows:
The wire which is colored green-and-yellow must be
connected to the terminal which is marked M with
the letter E or the safety earth or colored green or
green-and-yellow. The wire which is colored blue
must be connected to the terminal which is marked
with the letter N or colored black.
The wire which is colored brown must be connected
to the terminal which is marked with the letter L or
colored red.

For USA and Canada only
Use only the following power cord.

Getting Started

.

5

ENGLISH

Information for Users on Disposal of Old Equipment and Batteries

[European Union only]

These symbols indicate that equipment with these symbols should not be disposed
of as general household waste. If you want to dispose of the product or battery,
please consider the collection systems or facilities for appropriate recycling.

Notice: The sign Pb below the symbol for batteries indicates that this battery

contains lead.

Benutzerinformationen zur Entsorgung alter Geräte und Batterien

[Nur Europäische Union]

Diese Symbole zeigen an, dass derartig gekennzeichnete Geräte nicht als normaler
Haushaltsabfall entsorgt werden dürfen. Wenden Sie sich zur Entsorgung des
Produkts oder der Batterie an die hierfür vorgesehenen Sammelstellen oder
Einrichtungen, damit eine fachgerechte Wiederverwertung möglich ist.

Hinweis:

Notification:

Das Zeichen Pb unterhalb des Batteriesymbols gibt an, dass diese
Batterie Blei enthält.

Informations relatives à l’élimination des appareils et des piles usagés, à l’intention
des utilisateurs

[Union européenne seulement]

Si ces symboles figurent sur les produits, cela signifie qu’ils ne doivent pas être
jetés comme déchets ménagers. Si vous voulez jeter ce produit ou cette pile,
veuillez considérer le système de collecte des déchets ou les centres de
recyclage appropriés.

La symbole Pb en dessous du symbole des piles indique que cette
pile contient du plomb.

Informatie voor gebruikers over het verwijderen van oude apparatuur en batterijen

[Alleen Europese Unie]

Deze symbolen geven aan dat appara tuur met dit symbool niet mag worden
weggegooid als algemeen huishoudelijk afval. Als u het product of de batterij wilt
weggooien, kun t u inzamelsystemen of faciliteiten voor een geschikte recycling
gebruiken.

Opmerking: Het teken Pb onder het batterijsymboo l geeft aan dat deze batterij

lood bevat.

Battery

Batterie

Pile

Batterij

Products

Produkte

Produits

Producten

DEUTSCH

FRANÇAIS

NEDERLANDS

Información para los usuarios sobre la eliminación de baterías/pilas usadas

[Sólo Unión Europea]

Estos símbolos indican que el equipo con estos símbolos no debe desecharse
con la basura doméstica. Si desea desechar el producto o batería/pila, acuda
a los sistemas o centros de recogida para que los reciclen debidamente.

Atención: La indicación Pb debajo del símbolo de batería/pila indica que ésta

contiene plomo.

Baterías/pilas

Productos

ESPAÑOL / CASTELLANO

Getting Started

.

6

ITALIANO

Informazioni per gli utenti sullo smaltimento delle apparecchiature e batterie obsolete

[Solo per l’Unione Europea]

Questi simboli indicano che le apparecchiature a cui sono relativi non devono
essere smaltite tra i rifiuti domestici generici. Se si desidera smaltire questo
prodotto o questa batteria, prendere in considerazione i sistem i o le strutture di
raccolta appropriati per il riciclaggio corretto.

Nota: Il simbolo Pb sotto il simbolo delle batter ie indica che questa batteria contiene

piombo.

Informação para os utilizadores acerca da eliminação de equipamento usado e pilhas

[Apenas União Europeia]

Estes símbolos indicam que o equipamento com estes símbolos não deve ser
eliminado juntamente com o restante lixo doméstico. Se p retende eliminar
o produto ou a pilha, utilize os sistemas de recolha ou instalações para uma
reciclagem apropriada.

Aviso:

Σημείωση:

O sinal Pb abaixo do símbolo para pilhas indica que esta pilha contém
chumbo.

Πληροφορίες για την απόρριψη παλαιού εξοπλισμού και μπαταριών

[ Ευρωπαϊκή Ένωση μόνο ]

Αυτά τα σύμβολα υποδηλώνουν ότι ο εξοπλισμός που τα φέρει δεν θα πρέπει
να απορριφθεί ως κοινό οικιακό απόρριμμα . Εάν επιθυμείτε την απόρριψη
αυτού του προϊόντος ή αυτής της μπαταρίας , χρησιμοποιήστε το σύστημα
περισυλλογής ή εγκαταστάσεις για ανάλογη ανακύκλωση .

Το σύμβολο Pb κάτω από το σύμβολο μπαταρίας υποδηλώνει ότι
η μπαταρία περιέχει μόλυβδο .

Brugerinformation om bortskaffelse af gammelt udstyr og batterier

[Kun EU]

Disse symboler angiver, at udstyr med disse symboler ikke må bortskaffes som
almindeligt husholdningsaffald. Hvis du ønsker at smide dette produkt eller batteri
ud, bedes du overveje at bruge indsamlingssystem et eller steder, hvor der kan
ske korrekt gen brug.

Bemærk: Tegnet Pb under symbolet for batterierne angiver, at dette batteri

indeholder bly.

Batteria

Pilha

Μπαταρία

Batteri

Prodotti

Produtos

Προϊόντα

Produkter

PORTUGUÊS

ΕΛΛΗΝΙΚΑ

DANSK

Tietoja vanhojen laitteiden ja akkujen hävittämisestä

[Vain Euroopan unioni]

Nämä symbolit ilmaisevat, että symboleilla merk ittyä laitetta ei tulisi hävittää
tavallisen kotitalousjätteen mukana. Jos haluat hävit tää tuotteen tai sen akun,
tee se hyödyntämällä akkujen keräyspisteitä tai muita kier rätyspaikkoja.

Huomautus: Akkusymbolin alapuolella oleva Pb-merk intä tarkoit taa, että akku

sisältää lyijyä.

Akku

Tuotteet

SUOMI

Getting Started

.

7

SVENSKA

Information för användare gällande bortskaffning av gammal utrustning och batterier

[Endast den Europeiska unionen]

Dessa symboler indikerar att utrustning med dessa symboler inte ska hanteras
som vanligt hushållsavfall. Om du vill bortsk affa produkten eller batteriet ska du
använda uppsamlingssystem eller inrättningar för lämplig återvinning.

Observera: Märkningen Pb under symbolen för batterier indikerar att detta batteri

innehåller bly.

Opplysninger til brukere om kassering av gammelt utstyr og batterier

[Bare EU]

Disse symbolene viser at utstyr med dette symbolet, ikke skal kastes sammen
med vanlig husholdningsavfall. Hvis du vil kass ere dette produkte t eller batteriet,
skal du vurdere å bruke innsam lingssystemene eller andre muligheter for riktig
gjenbruk.

Merk:

Уведомление:

Tegnet Pb under symbolet for batterie r, viser at batteriet inneholder bly.

Сведения для пользователей по утилизации старого оборудования и батарей

[только для Европейского союза]

Данные символы указывают на то, что оборудование, на которое они
нанесены, не должны утилизироваться, как обычные бытовые отходы. При
необходимости утилизировать такое изделие или батарею обратитесь в
специальный пункт сбора для их надлежащей переработки.

Надпись Pb под символом батар ей указывает на то, что
данная батарея содержит свинец.

Informace pro uživatele k likvid aci starého zařízení a baterií

[Pouze Evropská unie]

Tyto symboly označují, že produkty s těmito symboly se nesmí likvidovat jako
běžný odpad. Pokud chcete produkt nebo baterii zlikvidovat, využijte sběrný
systém nebo jiné zařízení, které zaji stí řádnou recyklaci.

Bemærk: Značka Pb pod symbolem pro ba te rie znamená, že tato baterie

obsahuje olovo.

Batteri

Batteri

Батарея

Baterie

Produkter

Produkter

Изделия

Produkty

NORSK

Informacje dla użytkowników dotyczące poz bywania się zużytego sprzętu i baterii

[Tylko kraje Unii Europejskiej]

Te symbole oznaczają, że sprzę tu nie należy wyr zucać razem z odpadami
gospodarczymi. Jeśli trzeba po zbyć się tego produktu lub ba terii, proszę
skorzystać z systemu odbioru lub urządzeń do zbió rki odpadów elektronicznych,
w celu odpowiedniego ponowne go ich przetworzenia.

Uwaga: Oznaczenie Pb, znajdujące się pod symbole m baterii wskazuje, że ta

bateria zawiera ołów.

Bateria

Produkty

POLSKI

Getting Started

.

8

MAGYAR

Felhasználói információ az elhasznált be rendezések és akkumulátorok elhelyezéséről

[Csak az Európai Unióban]

Ez a szimbólum azt jelzi, hogy a berendezés nem helyezhető az általános
háztartási hulladék közé. Ha meg szeretne szabadulni a terméktől vagy az
akkumulátortól, akkor legyen tekintettel az gyűjtő rendszerre vagy intézményekre
a megfelelő hasznosítás érdekében.

Megjegyzés: Az alábbi Pb szimbólum - ha az akkum ulátoron megtalálható - azt

jelzi, hogy az akkumulátor ólmot tartalmaz.

Informacije za korisnike o odlaganju stare opreme i baterija

[Samo u zemljama gde se primenjuje]

Ovi simboli ukazuju da proizvod i baterije sa ovim simbolom ne smeju biti odloženi
kao nesortiran kućni otpad. Ako želite da ih se rešite, molimo vas da ne
upotrebljavate običnu kantu za đubre. Postoje zasebni sistemi za prikupljanje
ovakvih proizvoda.

Naznaka: Hemijski simbol Pb ispod simbola za baterije ukazuje na to da li baterija

sadrži olovo.

Akkumulátor

Baterija

Termékek

Produkt

Cрпска

Getting Started

.

9

Contents

Getting Started

Getting Started

Safety Precautions .................................................. 2

Accessories/Optional Accessories ........................

Check the Accessories ...................................... 11

Optional Accessories ......................................... 11

Main Features ....................................................... 12

Controls and Features ........................................... 14

Main Unit - Front ................................................ 14

Main Unit - Bottom ............................................. 14

Main Unit - Rear ................................................. 15

Main Unit - Input Terminals ................................ 16

Remote Control ................................................. 17

Loading Batteries into the Remote Control ........ 18

Effective Range of Remote Control Unit ............ 18

Set up

Installing the Projector ........................................... 19

Precautions during Installation ........................... 19

Precautions during Mounting ............................. 20

Adjusting the Position ........................................ 21

Connecting the Projector ....................................... 22

Connecting to the HDMI Input Terminal (Digital

Input) ................................................................. 22

Connecting to the LAN Terminal ........................ 23

Connecting to the RS-232C Terminal ................ 23

Connecting to the TRIGGER Terminal ............... 24

Connecting the Power Cord (Supplied Accessory)

Operate

Viewing Videos ...................................................... 25

Adjusting the Projector Screen .............................. 27

Adjusting the Lens According to the Projection

Position .............................................................. 27

Saving and Retrieving Adjustment Settings ....... 28

Adjusting Image Quality Automatically According to

the Viewing Environment ................................... 30

Adjusting the Screen Size (Aspect) ................... 31

Viewing 3D Movies ................................................ 32

Installing the 3D SYNCHRO EMITTER .............. 32

Viewing 3D Movies ............................................ 33

Converting 2D Movies to 3D Movies for Viewing

Adjusting 3D Movies .......................................... 34

Adjust/Set

Selecting an Image Quality According to the Video

Type ...................................................................... 35

Setting the Picture Mode ................................... 35

11

...... 24

....... 34

Setting the Color Profile ..................................... 36

Adjusting to the Preferred Color (Color
Management)

Adjusting Movies for Increased Expressiveness

(Multiple Pixel Control) .......................................... 39

Fine-tuning the Image Quality ............................... 41

Adjusting the Output Value of the Projected Image

(Gamma) ........................................................... 41

Fine-tuning to the Preferred Gamma Setting ..... 42

Reducing the After-image of Fast-moving Images

(Clear Motion Drive (C.M.D.)) ............................ 44

Viewing High Contrast Images (Lens Aperture) . 44

Adjustments and Settings in the Menu .................. 45

List of Menu Items ............................................. 45

Picture Adjust .................................................... 47

Input Signal ........................................................ 50

Installation ......................................................... 52

Display Setup .................................................... 58

Function ............................................................. 59

Information ......................................................... 60

.................................................... 38

Maintenance

Replacing the Lamp .............................................. 61

Lamp Replacement Procedure .......................... 61

Resetting the Lamp Time ................................... 63

Maintaining the Cabinet and Remote Control ........ 63

Cleaning and Replacing the Filter ......................... 64

Troubleshooting

Troubleshooting .................................................... 65

When the following messages appear... ................ 69

Others

External Control .................................................... 70

RS-232C Specifications ..................................... 70

TCP/IP Connection ............................................ 70

Command Format .............................................. 71

Remote Control Code ........................................ 72

Communications Example ................................. 73

Specifications ........................................................ 74

Index ..................................................................... 81

Symbols used in this manual

Z

indicates a function that is supported by DLA-RS6710.

Y

indicates a function that is supported by DLA-RS4910.

Items not marked with any of the above symbols are
supported by all models.

10

Accessories/Optional Accessories

Check the Accessories

Lens cover Y ................................................................. 1 piece

* It is attached to the main unit at the time of shipment.

Remote control ....................................................................... 1 piece

.

.

Getting Started

AAA-size batteries (for operational check) ............................ 2 pieces

Power cord (for USA) (about. 2 m) ......................................... 1 piece

.

Power cord (for UK) (about. 2 m) ............................................ 1 piece

.

Power cord (for EU) (about. 2 m) ............................................ 1 piece

.

0

INSTRUCTIONS (this book), warranty card, and other printed material are also included.

Optional Accessories

0

Replacement lamp model: PK-L2312U

0

3D GLASSES: model PK-AG3

0

3D SYNCHRO EMITTER: model PK-EM2

Compatibility Chart for 3D SYNCHRO EMITTER and 3D GLASSES

.

3D SYNCHRO EMITTER PK-EM1 *

(Communication

Method:

IR

(Infrared))

PK-EM2

(Communication

Method: RF (Radio

frequency))

* Discontinued product

Please check with your authorized dealer for details.

PK-AG1 *

(Communication

Method: IR (Infrared))

X X —

— — X

3D GLASSES

PK-AG2 *

(Communication

Method: IR

(Infrared))

PK-AG3

(Communication

Method: RF (Radio

frequency))

11

Main Features

The photos are for illustrative purposes only.

The photos are for illustrative

purposes only.

The photos are for illustrative purposes only.

Getting Started

New, impressive image quality with the 4K resolution

By employing JVC’s unique image-processing technology (MPC), focus and
blurring can be detected and adjusted in real time, allowing viewers to enjoy
the enhanced expressiveness of 4K images. (p. 39)

3D video expressions with a highly realistic feel

With the 3D feature, you can enjoy 3D movies with a more realistic effect.
(p. 32)

With the 2D-3D conversion feature, you can now enjoy 3D movies by
converting
video camera into 3D ones. (p. 34)

2D videos of

TV programs or those that are recorded using a home

Optimal image quality adjustment according to the viewing environment

Halation that occurs in environments such as a living room with white walls is
taken into consideration for optimal viewing. (p. 30)

0

You can
finer adjustments.
For more details, please refer to our website.

http://www3.jvckenwood.com/projector/support/index.html

utilize the

optional optical sensor and dedicated software to make

Flexible installation

In addition to the 2x motorized zoom & focus lens, the wide coverage of the lens shift functions also makes installation
of the projector more flexible. (p. 27)

The lens memory
to different video size formats easily.

feature, which enables focus, zoom, or shift settings to be saved or retrieved, enables you to switch

Customizable image quality adjustment feature

You can make adjustments according to the type of video
images or your preferences to enjoy the videos in optimal
quality. (p. 35)

The Real Color Imaging Technology (a color reproduction
technology developed by
image quality that is closer to the original image. (p. 36)

JVC) enables reproduction in an

12

Clear video expression with little after-image (C.M.D.)

Sharp depiction of details with minimal blur

The photos are for illustrative purposes only.

ABCD

After adjustmentBefore adjustment

The photos are for illustrative purposes only.

ABCD

ABCD

ABCD

®

After adjustmentBefore adjustment

The photos are for illustrative purposes only.

Optimal interpolation according to the content is made
possible with the new high-definition image interpolation
technique that supports 3D images.
Viewers can enjoy clear video expression with little after­image. (p. 44)

* C.M.D. is the abbreviation for Clear Motion Drive.

High-precision pixel adjustment feature

With the highly-precise “Pixel Adjust” feature, you can
enjoy a clear video quality with little color fringing
throughout the entire image.
(p. 53)

* Equipped

separately when an anamorphic lens is used and when
you are using the projector with a screen.

THX certification Z

THX 3D certification

The
cleared more than 400 image quality tests.

with two memories,

For Z, a “THX 3D Display Certification” by THX has been obtained.
In addition to 2D movies, you can also enjoy faithful reproduction of images in a “quality as
intended by the filmmaker” during playback of 3D movies.

is “an indication of high definition and high resolution”, which is granted to products that have

you can save the settings

Getting Started

isf certification

This unit is isf-certified, so calibration can be performed by an isf-certified trainer.
After calibration is performed, an isf mode is added to the Picture mode.

For more details, please refer to the isf website.
http://www.imagingscience.com/

Intelligent Lens Aperture

JVC has developed an image analysis algorithm, which
analyzes the state of the video image in real time, and
controls the aperture dynamically according to the image
information.
This technology enables viewers to enjoy video images
with enhanced contrast.

13

Controls and Features

ABC

D

E

E

FG

H

Getting Started

Main Unit - Front

.

A

Lens

This is a projection lens. Do not look through the lens
while an image is projected.

B

Lens cover Z

The lens cover opens/closes when the power supply
is turned on/off. (

0

For Y, attach the lens
in use.

C

Remote Sensor (front)

Please aim the remote control at this area when using
it.

* There is also a remote sensor at the rear.

p. 52)

cover when the unit is not

Main Unit - Bottom

D

Indicator

Refer to “Indicator Display on the Main Unit”p.

E

Exhaust vent

Warm air is discharged to cool down the internal
temperature.
Do not block the vents.

F

Inlets (at 3 points on the rear/bottom)

The inlets take in air to cool down the internal temperature.
Do not block or prevent the outflow of hot air. Doing so may cause
the unit to malfunction.

* There

G

H

are two inlets

Manual button for lens cover Z

The lens cover can be opened when pressed down.
It is used for maintenance purposes. You can also make use of it
when you need to open the lens cover urgently.

Feet

The height and angle of the projector can be adjusted by turning the
foot. (0 to 5 mm) (p. 21)

When the foot is removed, it can be used as the mounting holes for
the ceiling mount bracket.

on the right and left sides at the rear of the unit.

78.

14

Main Unit - Rear

F

IKLM

F

J

[MENU]: Displays the menu

[BACK]: Returns to the previous menu

[JKH I] keys: Selects an item

[OK]: Confirms a selection

[INPUT]: Switches the input

A [STANDBY/ON]: Turns “on”/“off” the
power

.

Getting Started

I

Input terminals

In addition to the video input terminal, there are also
other connection terminals for devices such as
controllers and optional equipment.

Please see
more details about the terminals.

J

Lamp cover

When replacing the light source lamp, remove this
cover.

K

Operation panel

For more details, please refer to the
panel” in the diagram below.

“Main Unit - Input Terminals”p.

16

“Operation

Operation panel

for

L

Remote Sensor (rear)

aim the remote control at this area when using

Please
it.

* There is also a remote sensor at the front.

M

Power input terminal

Connect the supplied power cord to this terminal.

.

15

Main Unit - Input Terminals

A B C

D

E

F

Enlarged View of Rear Face

Getting Started

.

A

[HDMI 1] input terminal

B

[HDMI 2] input terminal

For connecting to devices that support HDMI output.
(p. 22)

It is fitted to the M3 lock hole. The depth of the screw
hole is 3 mm.

C

[LAN] terminal (RJ-45)

The projector can be controlled by connecting it to a
PC through the computer network for control
commands to be sent to the projector.

D

[RS-232C] terminal (D-sub 9-pin
male)

The projector can
this terminal.

E

[3D SYNCHRO] terminal

By connecting a 3D SYNCHRO EMITTER (sold
separately) to this terminal, you can view 3D movies.

be controlled by connecting a PC to

F

[TRIGGER] terminal (E)

terminal for DC 12 V, 100 mA power supply. It

Output
is used for sending output signals to control devices
such as an elevating screen that is equipped with a
trigger function.

Note that improper connection may damage the
projector. (Tip=DC +12 V, Sleeve=GND)

16

Remote Control

INPUT

PHOTO

A

T

Y

W

G

F

C

D

K

O

M

B

E
H
I

J

L

N

P
Q
R

S

T

X

ED

V

Z

U

U

INFO.

Getting Started

O

[LIGHT]

Illuminates the buttons on the
remote control.

P

[JKH I] keys

For selecting an item.

Q

[OK]

Confirms a selected item.

R

[MENU]

Displays the menu,
or hides the menu if it is
displayed.

S

[BACK]

Returns to the previous menu.

T

[PICTURE MODE]

Switches the Picture mode to
[FILM]*, [CINEMA], [ANIME.],
[NATURAL], [PHOTO]*,
[STAGE], [THX]*, or [USER].
(p. 35)

* Z only

U

[ADVANCED
MENU]

Pressing the button each time
switches the menu in the
following sequence: “Picture
Mode”"“Color
Profile”"“Color
Temp.”"“Gamma”

V

[GAMMA]

For setting the gamma level.
(p. 41)

W

[COLOR TEMP.]

For setting the color
temperature. (p. 48)

X

[3D
FORMAT] Y

Switches the 3D format.
(p. 33)

Y

[COLOR P.FILE]

Switches the color profile.
(p. 36)

Z

[PIC. ADJ.]

Switches the items for
adjusting the image quality,
such as contrast, brightness,
etc. (p. 49)

17

A

B [STAND BY]

Turns off the power. (

B

C

[ON]

Turns on the power. (p. 25)

C

[INPUT]

Select an input from [HDMI 1]
and [HDMI 2]. (p. 25)

D

[3D SETTING]

Displays the 3D setting menu.
(p. 33)

E

[C.M.D.]

For setting frame interpolation.
(p. 44)

F

[INFO.] Y

Displays the information
menu. (p. 60)

G

[ENV.SETTING]

p. 26)

Y

Displays the “Environment
Setting” menu, (p. 30)

H

[LENS CONTROL]

For adjusting focus, zoom, and
shift. (p. 27)

I

[LENS MEMORY]

Switches between saving,
retrieving, and editing of the
lens memory. (p. 28)

J

[LENS AP.]

For setting the lens aperture.
(p. 44)

K

[MPC]

For setting the MPC level.
(p. 39)

L

[P.ANALYZER]

Turns on/off the analysis
screen. (p. 40)

M

[BEFORE/AFTER]

Displays the image before or
after an effect is applied. This
is used for MPC and Color
Management.
(p. 38, p. 39)

N

[HIDE]

Hides the image temporarily.
(p. 25)

Loading Batteries into the Remote Control

30°

30°

20°

20°

Remote Control

This unit

A

B

30°

30°

20°

20°

20°

20°

20°

20°

Screen

Remote Control

This unit

Getting Started

.

0

If the remote control

has to be brought closer to the projector to operate, it means that the batteries are wearing out.

Replace the batteries with new ones (AAA).

0

Insert the batteries according to the t s marks. Be sure to insert the s end first.

0

If an error occurs while using the remote control, remove the batteries and wait for five minutes. Load the batteries
again and operate the remote control.

Effective Range of Remote Control Unit

When aiming the remote control toward the sensor on this
unit

(front

or

rear),

ensure that the distance to the sensor
is within 7 m.
If the remote control fails to work properly, move closer
to this unit.

Control through reflection off a screen, etc.

Ensure that the total of distance A (between this unit and
the screen) and distance B (between the remote control
and the screen) is within 7 m.

As the efficiency of signals reflected from the remote

*

control unit varies with the type of screen used, the
operable distance may decrease.

.

.

CAUTION

0

Do not put the remote control in a place with an exposure to direct sun light or high temperature.
It may deformed due to heat, or the internal components may be adversely affected resulting in fire hazard.

0

Remove the batteries from the remote control when storing the remote control.
Storing the remote control for a prolonged period without removing the batteries can cause battery leakage.

18

Installing the Projector

Front

150 mm
and above

200 mm
and above

300 mm
and above

300 mm
and above

150 mm and above

5° 5°

15°

15°

15°

15°

Screen

Front

Precautions during Installation

Please read the following carefully before installing this
unit.

Do not install at the following

This unit is a precision device. Please refrain from
installing or using it

at the following locations. Otherwise,

it may cause fire or malfunction.

0

Dusty, wet and humid places

0

Places subject to oily smoke or cigarette smoke

0

On top of a carpet or bedding, or other soft surfaces

0

Places exposed to direct sunlight

0

Places with a high or low temperature

0

Do not install this unit in a room that is oily or subject

cigarette smoke. Even

to

a small quantity of smoke or

oiliness can have a long-term impact on this unit.

* This unit produces a great amount of heat, and is

designed to take in cool air to cool its optical
components. Using the unit at the above locations
may cause dirt to attach to the light path, thereby
resulting in dark images or dull colors.

* Dirt that sticks to the optical components cannot be

removed.

Maintain clearance from the wall, etc.

As the unit discharges a large amount of heat, install it
with adequate clearance from the surroundings as shown
below.

.

Using the projector

This unit uses a
in use.
Please refrain from projecting in the following
circumstances. Otherwise, it may cause fire or
malfunction.

0

Projection with the unit stood vertically

0

Projection with the unit inclined at an angle

Horizontal inclination: within ± 5 °

.

Vertical inclination: within ± 15 °

0

Malfunction may occur if the angle is not set within the
abovementioned range.

projection lamp, which will heat up when

.

.

Set up

Leave the front area of the unit unblocked.
If there is any obstructing object in front of the exhaust
vent, hot air will

flow back to the unit and cause it to heat
up. Hot air flowing out of the unit may cast shadows on
the screen (heat haze phenomenon).

Installing the screen

Install the unit and the screen such that they are
perpendicular to each other.

.

0

Please choose a screen material with non-uniform
patterns.

Uniform

patterns

such

as checks may cause

interference patterns to occur.

0

In this case, you

can change the size of the screen to

make the interference patterns less noticeable.

Using the projector at a high altitude

When using this unit at a location that is higher than 900
m above sea level (low air pressure), set the “High
Altitude Mode” to “On”. (p. 54)

19

Precautions during Mounting

Air Inlets

4 Locations

Securing (mounting) the projector

Set up

.

0

When this unit is

to be mounted to a fixed position for

use, install it horizontally.

0

Make sure to secure the main unit to prevent
accidents such as during an earthquake.

Securing with screws

Securing the projector (ceiling mount)

.

0

Be sure to ask your dealer to install the unit for you.
Installing the unit on your own may cause the unit to
fall resulting in injury.

0

Take the necessary actions to prevent the main unit
from falling off such as during an earthquake.

0

Regardless of the warranty period, JVC is not liable
for any product damage
with non-JVC ceiling fittings or to an environment that
is not suited for ceiling mount.

0

When using the unit with it suspended from a ceiling,
pay attention to the surrounding temperature. When
a heater is in use, the temperature around the ceiling
may be higher than expected.

0

attach the unit

To
torque between the range of 1.5N m to 2.0N m.
Tightening with torque exceeding the above range
may cause damage to the unit, which may result the
unit to fall.

caused by mounting the unit

to the ceiling mount bracket, set the

.

Remove the four feet at the bottom, and fasten using the
screws (M5 screws, 13 to 23 mm).

* Using screws other than

those designated may cause

the unit to break down.

* Leave a clearance of at least 10 mm from the bottom

surface of the unit to allow it to take in cool air.

20

Adjusting the Position

ContractExtend

Feet

90
80
70
60
50
40
30
20
10

0

10 3020 40

Lens movement range

Horizontal lens shift (%)

Vertical lens shift (%)

Lens shift Range

Up to about 80% of the
projected image

Horizontal Position: 0 % (Center)

Vertical Position

Up to about 34% of the
projected image

Vertical Position: 0% (Center)

Horizontal Position

■

■

■

Adjusting the elevation angle of the projector

The height and inclination of the unit (0 to 5 mm) can be
adjusted by turning the feet.
Lift the unit and adjust the four feet.

.

Adjusting the position of the image

By using the lens shift feature of this unit, you can shift
the image upward/downward or to the left/right. Set it to
your preferred position.

Æ “Adjusting the Lens According to the Projection
Position” （p.

27）

Set up

.

0

The maximum vertical shift varies with the amount of
horizontal shift. Similarly, the maximum horizontal
shift also changes with the amount of vertical shift.

0

The

values

the

graph are intended as a guide. Use

on

them for reference during installation.

21

Connecting the Projector

HDMI Output Terminal

BD/DVD Recorder, etc.

Laptop, etc.

HDMI Cable (Sold Separately)

This Unit

To [HDMI 1] or [HDMI 2] input
terminal



HDMI-DVI Conversion Cable (Sold Separately)

To [HDMI 1] or [HDMI 2] input
terminal

This Unit

DVI Output Terminal

Desktop PC, etc.

0

Do not turn on the power until connection is complete.

0

The connection procedures differ according to the device used. For details, please refer to the instruction manual
of the device to be connected.

0

This projector is used for projecting images. To output the audio of connected devices, please connect a separate
audio output device, such as an amplifier or speaker.

0

The images may not be displayed depending on the devices and cables to be connected.
Use only HDMI cables (sold separately) that are HDMI-certified.

0

Some cables cannot be connected to this unit due to the size of their connector cover.

Set up

Connecting to the HDMI Input Terminal (Digital Input)

Connecting via HDMI cable

.

0

If noise occurs, move the laptop away from this unit.

0

For a transmission bandwidth in compliance with the HDMI standard, a 340 MHz cable is recommended. When
using a cable with

a bandwidth of 75 MHz, you are recommended to set the resolution of the equipment transmitting

the video to 1080i or lower.

0

If the video is not displayed, try to reduce the length of the cable or lower the resolution of the video transmitting
equipment.

0

the source device

If

is connected to the projector through an intermediate device such as an AV amplifier or divider,
the video image may not appear depending on the specifications of the intermediate device.
In this case, connect the source device directly to the projector, and check whether the video image is displayed.

Connecting via HDMI-DVI conversion cable

.

0

If noise occurs, move the desktop PC away from this unit.

0

If the video is not displayed, try to reduce the length of the cable or lower the resolution of the video transmitting
equipment.

22

Connecting to the LAN Terminal

Desktop PC, etc.

Server

Hub

Network

Connection Cable

(Sold Separately)

This Unit

To [LAN] Terminal

RS-232C Terminal

Laptop, etc.

RS-232C Connection Cable (Sold Separately)

To [RS-232C] Terminal

This Unit

.

0

The network is used to control this unit. It is not used for sending or receiving video signals.

0

Please contact your network administrator for information concerning the network connection.

0

Set “ECO Mode” to “Off” if RS-232C/LAN communication is performed or the HDMI link function is used in the Standby
mode. (p. 59)

0

For more information on control, please refer to “External Control” (p. 70).

Connecting to the RS-232C Terminal

Set up

.

0

Set “ECO Mode” to “Off” if RS-232C/LAN communication is performed or the HDMI link function is used in the Standby
mode. (p. 59)

0

For more information on control, please refer to “External Control” (p. 70).

23

Connecting to the TRIGGER Terminal

Trigger Input Terminal (Ø3.5)

Screen

Trigger Cable (Sold Separately)

To [TRIGGER] Terminal

This Unit

A

B

Power Cord

(Supplied)

Set up

.

0

Do not use it to supply power to other devices.

0

Connecting to the audio terminal of another device may cause the device to malfunction or break down.

0

Using beyond the rated value will cause the unit to malfunction.

0

The trigger terminal outputs a voltage of 12 V. Exercise adequate caution to prevent short circuit.

0

The factory setting is “Off”. To change the setting, configure the “Trigger” item in the menu (

Connecting the Power Cord (Supplied Accessory)

p. 59).

0

0

0

0

0

0

A

Connect

the

power

cord

supplied to the power input terminal on

the main unit

B

Insert the supplied power plug into the wall outlet.

Precautions to prevent fire and electric shock

The voltage capacity of this unit is large. Please connect it directly to the wall outlet.
When you are not using the equipment, please unplug the power cord from the outlet.
Connect it using only the power cord supplied.
Do not use a voltage other than the indicated power voltage.
Do not damage, break or modify the power cord. Do not place a heavy object on the power cord, or heat or pull it.

Doing so may damage the power cord.
Do not unplug the power cord with wet hands.

24

Viewing Videos

LAMP WARNING

STANDBY/ON

LAMP WARNING

STANDBY/ON

During lamp startup

“STANDBY/ON” lights up (green)

In standby state

“STANDBY/ON” lights up (red)

HDMI 1

HDMI 2

LAMP WARNING

STANDBY/ON

INPUT

PHOTO

1

2

3

MEMO

0

When you are using Y, be sure to remove the lens cover.

0

Connect the power cord, and ensure that the “STANDBY/ON” indicator
lights up in red.

1

Turn on the power

Remote control: press the C [ON] button
Projector unit: press the A [STANDBY/ON] button

0

The “STANDBY/ON” indicator light
goes off after the unit starts up).

0

(Z) The motorized lens cover opens.

.

2

Choose the image to project

Pressing the [INPUT] button on the projector unit or remote control each
time switches the input mode as follows.

switches from red to green (light

Operate

.

0

Play back the selected device to project the image.

To hide the image temporarily
Press the [HIDE] button on the projector unit or remote control

0

The “STANDBY/ON” indicator light starts to blink in green.

0

Press the [HIDE] button again to resume display of the image.

0

The power cannot be turned off when the image is temporarily hidden.

25

3

LAMP WARNING

STANDBY/ON

LAMP

WARNING

STANDBY/ON

In standby state

“STANDBY/ON” lights up (red)

In the Cool-down mode

“STANDBY/ON” blinking (red)

Turn off the power

Remote control: press the B [STAND BY] button
Projector unit: press the A [STANDBY/ON] button

0

While the “Are you sure you want to turn off?” message is displayed, press the button again.

0

The lamp turns off, and the “STANDBY/ON” indicator switches from a green light to a red blinking light.

0

After the light goes off, the fan will run for about 100 seconds to cool down the lamp (Cool-down mode).
Do not disconnect the power cable while cooling is in progress.

0

After about 100 seconds, the “STANDBY/ON” indicator switches from a blinking red to a solid red light.

.

0

(Y) Attach the lens cover.

0

(Z) The motorized lens cover opens.

Operate

CAUTION

0

The power cannot be turned off within approximately 60 seconds after it has been turned on.

0

After the light goes off, the fan will run for about 100 seconds to cool down the lamp (Cool-down mode).
Do not disconnect the power cable while cooling is in progress.

0

The power cannot be turned on again while cooling is in progress (100 seconds).

0

Pull out the power plug when the unit is not to be used for a prolonged period of time.

26

Adjusting the Projector Screen

Focus

Shift (Screen Position)

Adjustment

Zoom (Screen Size)

Adjustment

ABCD

ABCD

ABCD

Focus Adjustment

INPUT

PHOTO

1

2

Adjusting the Lens According to the Projection Position

Press the [LENS CONTROL] button, and use the

1

[JKH I] keys to adjust Focus, Zoom (screen size),
and Shift (screen position)

.

0

Pressing the [LENS CONTROL] or [OK] button each time switches
the mode in the following sequence:
“Focus”"“Zoom”"“Shift”"“Focus”...

Operate

.

Press the [MENU] button once, or the [BACK] twice,

2

to end adjustment.

0

Operation of the lens control feature is disabled when the lens lock
is set to “On”.

27

Saving and Retrieving Adjustment Settings

MENU

BACK

-----

-----

-----

-----

-----

-----

-----

-----

-----

>>

-----

Back

Operate

Select

Exit

Lens Memory Save

Installation

INPUT

PHOTO

2

4

3

The Focus, Zoom, and Shift settings can be saved or retrieved, so you can

Operate

easily to a

switch

0

Pressing the [LENS MEMORY]
following sequence: “Lens Memory Save”"“Lens Memory Select”"“Lens
Memory Name Edit”"“Lens Memory Save”...

0

In a state where no adjustment settings are saved (factory default), only
“Lens Memory Save” is displayed.

0

Operation of the lens control feature is disabled when the lens lock is set
to “On”.

Saving an adjustment data

Adjust focus, zoom, or shift (p. 27)

1

Press the [LENS MEMORY] button to display “Lens

2

Memory Save”

0

You can also save an adjustment data by selecting
“Installation”"“Lens Control”"“Lens

different aspect ratio (screen size) according to the image.

button each time switches the mode in the

Memory Save” from the menu.

Select the item to save, and press the [OK] button

3

0

The adjustment data is saved.

0

Items with no adjustment data saved are displayed as [----].

0

If

.

you have selected

an item for which an adjustment data has already

been saved, the old data will be overwritten.

0

You can change the name when saving an item. (p. 29)

0

The maximum number of items can be saved is 10 for Z

and

5 for Y.

Press the [MENU] button to exit

28

4

Retrieving an adjustment data

MENU

BACK

-----

-----

-----

MEMORY2

-----

-----

-----

-----

-----

>>

MEMORY1

Back

Operate

Select

Exit

Lens Memory Select

Installation

MENU

BACK

-----

-----

-----

MEMORY2

-----

-----

-----

-----

-----

>>

MEMORY1

Lens Memory Name Edit

Back

Operate

Select

Exit

Installation

MENU

>>

MEMORY1

}

?

.

y

l

Y

L

{

=

,

x

k

X

K

]

/

0

w

j

W

J

[

-

9

v

i

V

I

>

+

8

y

h

U

H

<

*

7

t

g

T

G

)

&

6

s

f

S

F

(

%

5

r

e

R

E

~

$

4

q

d

Q

D

|

#

3

p

c

P

C

;

"

2

o

b

O

B

\

^

z

M

Z

m

@

:

!

1

n

a

N

A

SPACE

OKAll ClearClear

Name

Character List

Selection Cursor

Input Cursor

BACK

Back

Operate

Select

Exit

Lens Memory Name Edit

Installation

Press the [LENS MEMORY] button to display “Lens Memory Select”

1

0

Pressing

the [LENS MEMORY]

button each time switches the mode in the following sequence: “Lens Memory

Select”"“Lens Memory Save”"“Lens Memory Name Edit”"“Lens Memory Select”...

0

You can also retrieve an adjustment data by selecting “Installation”"“Lens Control”"“Lens Memory Select”
from the menu.

.

Select the adjustment data to retrieve, and press the [OK] button

2

0

The retrieved data is adjusted automatically.

0

If no adjustment data has been saved, the item will be grayed out and cannot be selected.

Renaming an adjustment data

Press the [LENS MEMORY] button to display “Lens Memory Name Edit”

1

0

Pressing the [LENS MEMORY] button each time switches the mode in the following sequence: “Lens Memory
Select”"“Lens Memory Save”"“Lens Memory Name Edit”"“Lens Memory Select”...

0

You can also edit an adjustment data by selecting “Installation”"“Lens Control”"“Lens Memory Name Edit”
from the menu.

Operate

.

Select the adjustment data to edit, and press the [OK] button

2

0

An edit screen appears.

.

0

You can input up to 10 characters.

0

Characters that are usable include alphabets (upper or lower case), numeric characters, and symbols.

0

Pressing the [Back] button cancels the content that is currently being edited, and exits the edit mode.

After renaming, select “OK” and press the [OK] button

3

Press the [MENU] button to exit

4

29

Adjusting Image Quality Automatically According to the Viewing

Projector

Viewer

Viewing

Distance

Screen Size

Screen

- Front View -

>>

MENU

BACK

0

MENU

BACK

0

3

21

Back

Operate

Select

Exit

Back

Operate

Select

Exit

Light

3m

100inch

Off

On

Wall C olor

Viewing Distance

Screen Size

Screen No.

Screen Adjust

Off

Front

Environment Setting

High Altitude Mode

Anamorphic

Pincushion

Keystone

Installation Style

Pixel Adjust

Lens Control

Installation Installation

Off

Environment Setting

Off

On

Adjust

>>

MENU

BACK

3

21

Back

Operate

Select

Exit

Light

3m

100inch

Off

On

Wall Color

Viewing Distance

Screen Size

Screen No.

Screen Adjust

Installation

Environment Setting

Adjust

Environment

By configuring “Environment Setting” according to the
viewing environment, image quality adjustment and
correction according to environmental differences are
performed

automatically

minimize

to

any influence on the

image quality.

0

“Environment Setting” is applied separately from the
individually adjusted data.

0

Screen correction cannot be performed when “Color
Profile” is set to “x.v.Color”.

.

Set Screen Adjust

3

By selecting the optimal correction mode
according to the characteristics of the screen in
use, corrections can be performed to reproduce
natural images with balanced colors.

Operate

1

2

Press the [MENU] button to display
the menu

Y:
Press the [ENV.SETTING] button on the remote
control to open the “Environment Setting” menu.

Select “Installation”"“Environment
Setting”"“On” from the menu

.

0

When “Environment Setting” is set to “Off”,
“Screen Size”, “Viewing Distance”, and “Wall
Color” are grayed out and cannot be selected.

.

0

This item is not

available when “Color Profile” is

set to “Off”.

0

Select a type from “1” to “106”.

0

For information on the screen and the
corresponding

correction mode, please

visit our

website.

http://www3.jvckenwood.com/english/projector/screen/

Select “Screen Size” to configure the

4

screen size to use

0

Select the closest screen size setting from the
range between “60inch” and “200inch” (in 10­inch increments).

Select “Viewing Distance” to

5

configure the viewing distance
(distance to the screen)

0

Select the closest viewing
the range between “1 m” and “10 m”.

0

For more details on the height, please refer to
“Screen Size and Projection Distance”p. 75.

Select “Wall Color” to configure the

6

wall color

0

If the wall is

dark in color, select “Dark”. For walls

with a color other than dark color, select “Light”.

Press the [MENU] button to exit

7

distance setting from

30

MEMO

0

You can utilize the optional optical sensor and
dedicated software to make finer adjustments.
For more information on the dedicated software,
please visit our website.

http://www3.jvckenwood.com/english/download/
index.html