Audio 500 mV(rms) (-4dBs), high impedance, RCA pin jack × 2
Y: 1 V (p-p), Positive (Negative sync provided), 75 Ω
C: 0.286 V (p-p) (Burst signal), 75 Ω
Video 1V (p-p), Positive (Negative sync provided), 75 Ω, RCA pin jack × 1
Audio 500 mV (rms), High impedance, RCA pin jack × 2
(Digital-input terminal is not compatible with picture signals of personal computer)
576i(625i),576p(625p),480i(525i),480p(525p),720p(750p),1080i(1125i) signals are available.
LT-26DB9BDLT-26ED91U
Contents
(No.YA606<Rev.002>)1-3
SECTION 1
PRECAUTION
1.1SAFETY PRECAUTIONS [EXCEPT FOR UK]
(1) The design of this product contains special hardware,
many circuits and components specially for safety
purposes. For continued protection, no changes should be
made to the original design unless authorized in writing by
the manufacturer. Replacement parts must be identical to
those used in the original circuits. Service should be
performed by qualified personnel only.
(2) Alterations of the design or circuitry of the products should
not be made. Any design alterations or additions will void
the manufacturer's warranty and will further relieve the
manufacturer of responsibility for personal injury or
property damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These
characteristics are often not evident from visual inspection
nor can the protection afforded by them necessarily be
obtained by using replacement components rated for
higher voltage, wattage, etc. Replacement parts which
have these special safety characteristics are identified in
the parts list of Service manual. Electrical components
having such features are identified by shading on the
schematics and by ( ) on the parts list in Service
manual. The use of a substitute replacement which does
not have the same safety characteristics as the
recommended replacement part shown in the parts list of
Service manual may cause shock, fire, or other hazards.
(4) Don't short between the LIVE side ground and
ISOLATED (NEUTRAL) side ground or EARTH side
ground when repairing.
Some model's power circuit is partly different in the GND.
The difference of the GND is shown by the LIVE : ( ) side
GND, the ISOLATED (NEUTRAL) : ( ) side GND and
EARTH : ( ) side GND.
Don't short between the LIVE side GND and ISOLATED
(NEUTRAL) side GND or EARTH side GND and never
measure the LIVE side GND and ISOLATED (NEUTRAL)
side GND or EARTH side GND at the same time with a
measuring apparatus (oscilloscope etc.). If above note will
not be kept, a fuse or any parts will be broken.
(5) When service is required, observe the original lead dress.
Extra precaution should be given to assure correct lead
dress in the high voltage circuit area. Where a short circuit
has occurred, those components that indicate evidence of
overheating should be replaced. Always use the
manufacturer's replacement components.
(6) Isolation Check (Safety for Electrical Shock Hazard)
After re-assembling the product, always perform an isolation check on the exposed metal parts of the cabinet (antenna terminals, video/audio input and output terminals,
Control knobs, metal cabinet, screw heads, earphone jack,
control shafts, etc.) to be sure the product is safe to operate
without danger of electrical shock.
a) Dielectric Strength Test
The isolation between the AC primary circuit and all metal
parts exposed to the user, particularly any exposed metal
part having a return path to the chassis should withstand a
voltage of 3000V AC (r.m.s.) for a period of one second. (.
. . . Withstand a voltage of 1100V AC (r.m.s.) to an appliance rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated 200V or more, for a period of one second.)
This method of test requires a test equipment not generally
found in the service trade.
b) Leakage Current Check
Plug the AC line cord directly into the AC outlet (do not use
a line isolation transformer during this check.). Using a
"Leakage Current Tester", measure the leakage current
from each exposed metal part of the cabinet, particularly
any exposed metal part having a return path to the chassis,
to a known good earth ground (water pipe, etc.). Any leakage current must not exceed 0.5mA AC (r.m.s.).
However, in tropical area, this must not exceed 0.2mA AC
(r.m.s.).
Alternate Check Method
Plug the AC line cord directly into the AC outlet (do not
use a line isolation transformer during this check.). Use
an AC voltmeter having 1000Ω per volt or more
sensitivity in the following manner. Connect a 1500Ω
10W resistor paralleled by a 0.15µF AC-type capacitor
between an exposed metal part and a known good earth
ground (water pipe, etc.). Measure the AC voltage
across the resistor with the AC voltmeter. Move the
resistor connection to each exposed metal part,
particularly any exposed metal part having a return path
to the chassis, and measure the AC voltage across the
resistor. Now, reverse the plug in the AC outlet and
repeat each measurement. Any voltage measured must
not exceed 0.75V AC (r.m.s.). This corresponds to
0.7mA AC (r.m.s.).
However, in tropical area, this must not exceed 0.35V
AC (r.m.s.). This corresponds to 0.3mA AC (r.m.s.).
AC VOLTMETER
(HAVING 1000 /V,
OR MORE SENSITIVITY)
1-4 (No.YA606<Rev.002>)
0.15 F AC-TYPE
GOOD EARTH GROUND
1500 10W
PLACE THIS PROBE
ON EACH EXPOSED
ME TAL PAR T
1.2SAFETY PRECAUTIONS [FOR UK]
(1) The design of this product contains special hardware and many circuits and components specially for safety purposes. For
continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer.
Replacement parts must be identical to those used in the original circuits. Service should be performed by qualified personnel
only.
(2) Alterations of the design or circuitry of the product should not be made. Any design alterations or additions will void the
manufacturer's warranty and will further relieve the manufacturer of responsibility for personal injury or property damage
resulting therefrom.
(3) Many electrical and mechanical parts in the product have special safety-related characteristics. These characteristics are often
not evident from visual inspection nor can the protection afforded by them necessary be obtained by using replacement
components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are
identified in the Parts List of Service Manual. Electrical components having such features are identified by shading on the
schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the
same safety characteristics as the recommended replacement part shown in the Parts List of Service Manual may cause shock,
fire, or other hazards.
(4) The leads in the products are routed and dressed with ties, clamps, tubing’s, barriers and the like to be separated from live parts,
high temperature parts, moving parts and / or sharp edges for the prevention of electric shock and fire hazard. When service is
required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to
normal, after re-assembling.
WARNING
(1) The equipment has been designed and manufactured to meet international safety standards.
(2) It is the legal responsibility of the repairer to ensure that these safety standards are maintained.
(3) Repairs must be made in accordance with the relevant safety standards.
(4) It is essential that safety critical components are replaced by approved parts.
(5) If mains voltage selector is provided, check setting for local voltage.
1.3INSTALLATION
1.3.1 HEAT DISSIPATION
If the heat dissipation vent behind this unit is blocked, cooling
efficiency may deteriorate and temperature inside the unit will
rise. The temperature sensor that protects the unit will be
activated when internal temperature exceeds the pre-determined
level and power will be turned off automatically.Therefore,
please make sure pay attention not to block the heat dissipation
vent as well as the ventilation outlet behind the unit and ensure
that there is room for ventilation around it.
Ventilation hole
*Diagram differs from actual appearance.
1.3.3 INSTALLATION REQUIREMENTS
Ensure that the minimal distance is maintained, as specified
below, between the unit with and the surrounding walls, as well
as the floor etc.Install the unit on stable flooring or stands.Take
precautionary measures to prevent the unit from tipping in order
to protect against accidents and earthquakes.
200 mm
150 mm50
*Diagram differs from actual appearance.
mm
150 mm50 mm
1.3.4 INSTALLATION REQUIREMENTS
To ensure safety in an emergency such as an earthquake, and
to prevent accidents, ensure that measures are taken to prevent
the TV dropping or falling over.
1.3.2 NOTES ON HANDLING
When taking the unit out of a packing case, do not grasp the
upper part of the unit. If you take the unit out while grasping the
upper part, the LCD PANEL may be damaged because of a
pressure. Instead of grasping the upper part, put your hands on
the lower backside or sides of the unit.
It fixes in a band.
TV STAND
*Diagram differs from actual appearance.
(No.YA606<Rev.002>)1-5
1.4HANDLING LCD PANEL
1.4.1 PRECAUTIONS FOR TRANSPORTATION
When transporting the unit, pressure exerted on the internal LCD
panel due to improper handling (such as tossing and dropping)
may cause damages even when the unit is carefully packed. To
prevent accidents from occurring during transportation, pay
careful attention before delivery, such as through explaining the
handling instructions to transporters.
Ensure that the following requirements are met during
transportation, as the LCD panel of this unit is made of glass and
therefore fragile:
(1) USE A SPECIAL PACKING CASE FOR THE LCD PANEL
When transporting the LCD panel of the unit, use a special
packing case (packing materials). A special packing case
is used when a LCD panel is supplied as a service spare
part.
(2) ATTACH PROTECTION SHEET TO THE FRONT
Since the front (display part) of the panel is vulnerable,
attach the protection sheet to the front of the LCD panel
before transportation. Protection sheet is used when a LCD
panel is supplied as a service spare part.
(3) AVOID VIBRATIONS AND IMPACTS
The unit may be broken if it is toppled sideways even when
properly packed. Continuous vibration may shift the gap of
the panel, and the unit may not be able to display images
properly. Ensure that the unit is carried by at least 2
persons and pay careful attention not to exert any vibration
or impact on it.
(4) DO NOT PLACE EQUIPMENT HORIZONTALLY
Ensure that it is placed upright and not horizontally during
transportation and storage as the LCD panel is very
vulnerable to lateral impacts and may break. During
transportation, ensure that the unit is loaded along the
traveling direction of the vehicle, and avoid stacking them
on one another. For storage, ensure that they are stacked
in 2 layers or less even when placed upright.
1.4.2 OPTICAL FILTER (ON THE FRONT OF THE LCD PANEL)
(1) Avoid placing the unit under direct sunlight over a
prolonged period of time. This may cause the optical filter
to deteriorate in quality and COLOUR.
(2) Clean the filter surface by wiping it softly and lightly with a
soft and lightly fuzz cloth (such as outing flannel).
(3) Do not use solvents such as benzene or thinner to wipe the
filter surface. This may cause the filter to deteriorate in
quality or the coating on the surface to come off. When
cleaning the filter, usually use the neutral detergent diluted
with water. When cleaning the dirty filter, use water-diluted
ethanol.
(4) Since the filter surface is fragile, do not scratch or hit it with
hard materials. Be careful enough not to touch the front
surface, especially when taking the unit out of the packing
case or during transportation.
1.4.3 PRECAUTIONS FOR REPLACEMENT OF EXTERIOR
PARTS
Take note of the following when replacing exterior parts (REAR
COVER, FRONT PANEL, etc.):
(1) Do not exert pressure on the front of the LCD panel (filter
surface). It may cause irregular COLOUR.
(2) Pay careful attention not to scratch or stain the front of the
LCD panel (filter surface) with hands.
(3) When replacing exterior parts, the front (LCD panel) should
be placed facing downward. Place a mat, etc. underneath
to avoid causing scratches to the front (filter surface).
1-6 (No.YA606<Rev.002>)
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
2.1FEATURES
DIGITAL TUNER
This TV can receive both DVB-T (Digital terrestrial broadcasting:
DA9/DB9/EP9U only), DVB-S(Digital satellite broadcasting: DB9
only), DVB-C(Digital cable broadcasting: DH9 only) and
Analogue terrestrial broadcasting.
HDMI INPUT
By connecting a HDMI compatible device, high definition
pictures can be displayed on your TV in their digital form.
2.2MAIN DIFFERENCE LIST
Items
Satellite Broadcasting NOYESNO
Cable BroadcastingNOYES
Power Consumption
TV RF System
(Digital)
Receiving Frequency
(Digital)
Teletext System
(Digital)
Remote control unitRM-C1892BRM-C1899SRM-C1892B
LT-26DA9BJ
140 W (Standby: 0.9 W)150 W (Standby: 0.9 W) 140 W (Standby: 0.9 W)
DVB-TDVB-T / DVB-SDVB-C
UHF:474 MHz - 858 MHz
MHEG 5 UK profile EBU TEXT
LT-26DA9BU
LT-26DA9BN
PICTURE MODE
This function can adjust the picture settings automatically.
There are BRIGHT, STANDARD, SOFT and MANUAL in the
PICTURE MODE.
ZOOM
This function can change the screen size according to the
picture aspect ratio.
Pin No. Signal designationMatching valueEXT-1EXT-2
1AUDIO R output500mV(rms) (Nominal), Low impedanceUsed (TV OUT)Used (LINE OUT)
2AUDIO R input500mV(rms) (Nominal), High impedanceUsed (R1)Used (R2)
3AUDIO L output500mV(rms) (Nominal), Low impedanceUsed (TV OUT)Used (LINE OUT)
4AUDIO GNDUsedUsed
5GND (B)UsedUsed
6AUDIO L input500mV(rms) (Nominal), High impedanceUsed (L1)Used (L2)
7B input700mV
8FUNCTION SW
(SLOW SW)
Low : 0V-3V
High : 8V-12V, High impedance
, 75ΩUsedNot used
(B-W)
UsedUsed
9GND (G)UsedUsed
10SCLNot used Used (SCL2)
11G input700mV
, 75ΩUsedNot used
(B-W)
12SDANot used Used (SDA2)
13GND (R)UsedUsed
14GND (YS)UsedNot used
15R / C inputR : 700mV
C : 300mV
(B-W)
(P-P)
, 75Ω
, 75Ω
Used (R)Used (C2)
16Ys input (FAST SW) Low : 0V-0.4V, High : 1V-3V, 75ΩUsedNot used
17GND (VIDEO output)UsedUsed
18GND (VIDEO input)UsedUsed
19VIDEO output1V
20VIDEO / Y input1V
(Negative sync), 75ΩUsed (TV OUT)Used (LINE OUT)
(P-P)
(Negative sync), 75ΩUsedUsed
(P-P)
21COMMON GNDUsedUsed
(P-P= Peak to Peak, B-W= Blanking to white peak)
[Pin assignment]
20 18 16 14 12 10 8 6 4 2
21 19 17 15 13 11 9 7 5 3 1
1-8 (No.YA606<Rev.002>)
2.4TECHNICAL INFORMATION
2.4.1 LCD PANEL
This unit uses the flat type LCD (Liquid Crystal Display) panel that occupies little space, instead of using the conventional
CRT(Cathode Ray Tube). This panel adopts "normally white" mode where the transmittance or reflective rate is maximum, and the
screen is white when no voltage is applied.
2.4.1.1SPECIFICATIONS
The following table shows the specifications of this unit.
ItemSpecifications
Maximum dimensions ( W × H × D )626.0 mm × 373.0mm × 42.0 mm
Weight4.5 kg
Effective screen sizeDiagonal : 66.0 cm (H: 57.6 cm × V: 32.3 cm)
Aspect ratio16 : 9
Drive device / systema-Si-TFT active matrix system
ResolutionHorizontally 1366 × Vertically 768 × RGB < W-XGA > 3147264 dots in total
Pixel pitch (pixel size)Horizontally: 0.1405 mm, Vertically: 0.4215 mm
Displayed color16777216 colors 256 colors for R G and B
Surface polarizerAnti-Glare type Low reflective coat
Color filterVertical stripe
BacklightCold cathode fluorescent lamp × 12
Power supply voltage in LCD5 V
Power supply voltage in inverter24 V
Panel interface systemLVDS (Low Voltage Differential Signaling)
2.4.1.2PIXEL FAULT
There are three pixel faults - bright fault , dark fault and flicker fault - that are respectively defined as follows.
BRIGHT FAULT
In this pixel fault, a cell that should not light originally is lighting on and off.
For checking this pixel fault, input ALL BLACK SCREEN and find out the cell that is lighting on and off.
DARK FAULT
In this pixel fault, a cell that should light originally is not lighting or lighting with the brightness twice as brighter as originally lighting.
For checking this pixel fault, input 100% of each R/G/B colour and find out the cell that is not lighting.
FLICKER FAULT
In the pixel fault, a cell that should light originally or not light originally is flashing on and off.
For checking this pixel fault, input ALL BLACK SCREEN signal or 100% of each RGB colour and find out the cell that is flashing on
and off.
(No.YA606<Rev.002>)1-9
SECTION 3
DISASSEMBLY
3.1CAUTION AT DISASSEMBLY
• Make sure that the power cord is disconnected from the outlet.
• Pay special attention not to break or damage the parts.
• Make sure that there is no bent or stain on the connectors before inserting, and firmly insert the connectors.
• Be sure to reattach the wire clamps removed during the procedure to the original positions. (Attaching the wire clamps in wrong
positions may affect the performance.)
REFERENCE:
When removing each board, remove the connector if necessary. The operation is easier if you write down the connection points
(connector numbers) of the connector. For connection of each board, refer to the "WIRING DIAGRAM" of the Standard Circuit
Diagram.
3.2DISASSEMBLY PROCEDURE
3.2.1 REMOVING THE REAR COVER (Fig.3-1)
(1) Remove the 7 screws [A] and 2 screws [B].
(2) Remove the REAR COVER.
3.2.2 REMOVING THE POWER UNIT (Fig.3-1)
• Remove the REAR COVER.
(1) Remove the 4 screws [C].
(2) Remove the POWER UNIT.
3.2.3 REMOVING THE MAIN PWB / MPEG PWB (Fig.3-1)
• Remove the REAR COVER.
(1) Remove the 2 screws [D].
(2) Remove the SIDE SHIELD.
(3) Remove the 4 screws [E] and 4 screws [F].
(4) Remove the MAIN PWB and MPEG PWB together.
(5) Remove the connector connecting the MAIN PWB and
MPEG PWB to separate each board.
3.2.4 REMOVING THE KEY PWB (Fig.3-1)
• Remove the REAR COVER.
(1) Remove the 2 screws [G].
(2) Remove the CONTROL BASE and KEY PWB together.
(3) Remove the 2 screws [H].
(4) Remove the KEY PWB from the CONTROL BASE.
3.2.7 REMOVING THE SPEAKER (Fig.3-1)
• Remove the REAR COVER.
(1) Remove the 2 screws [M].
(2) Remove the SPEAKER.
(3) Follow the same steps when removing the other
SPEAKER.
3.2.8 REMOVING THE IR PWB (Fig.3-1)
• Remove the REAR COVER.
(1) Remove the 1 screw [N].
(2) Remove the IR PWB.
3.2.9 REMOVING THE STAND (Fig.3-1)
(1) Remove the 2 screws [P].
(2) Remove the STAND.
3.2.10 REMOVING THE LCD CONTROL PWB (Fig.3-1)
• Remove the REAR COVER.
• Remove the STAND.
(1) Remove the 4 screws [Q], 4 screws [R] and 4 screws [S].
(2) Remove the MAIN SHIELD.
(3) Remove the 4 screws [T].
(4) Remove the LCD CONTROL PWB COVER.
(5) Remove the LCD CONTROL PWB.
3.2.5 REMOVING THE INVERTER PWB (Fig.3-1)
• Remove the REAR COVER.
(1) Remove the 5 screws [J].
(2) Remove the INVERTER PWB COVER.
(3) Remove the 1 screw [K].
(4) Remove the INVERTER PWB.
3.2.6 REMOVING THE POWER BRACKET (Fig.3-1)
• Remove the REAR COVER.
(1) Remove the 2 screws [L].
(2) Remove the POWER BRACKET.
1-10 (No.YA606<Rev.002>)
3.2.11 REMOVING THE LCD PANEL UNIT (Fig.3-1)
• Remove the REAR COVER.
• Remove the STAND.
• Remove the MAIN SHIELD.
(1) Remove the 2 screws [U].
(2) Remove the PANEL BRACKET.
(3) Remove the LCD PANEL UNIT.
B
D
A
C
POWER UNIT
INVERTER
PWB COVER
REAR COVER
L
J
S
POWER
BRACKET
T
LCD CONTROL
PWB COVER
LCD CONTROL
PWB
SIDE
SHIELD
SMART DTV PWB
E
F
Q
S
R
MAINSHIELD
MAIN PWB
P
S
PANE L
BRACKET
U
STAND
K
CONTROL
KNOB
CONTROL
BASE
INVERTER
PWB
G
LCD PANEL
19191919M
U
PANE L
BRACKET
BLUE LED MODULE
SPEAKER
N
IR PWB
M
H
SPEAKER
KEY PWB
Fig.3-1
FRONT
CABINET
(No.YA606<Rev.002>)1-11
3.3 MEMORY IC REPLACEMENT
Service
Hardware Ver : REV X.X
Sub MCU SW Ver : REV X.X
ATV SW Ver : XXXXXX X.XX.XX
DTV SW Ver : XXXXXX X.XX.XX
Sub MCU Loader Ver : XX.XX
DTV Loader Ver : XX.XX
ATV Loader Ver : X. X. X
System ID : XXXX.XXXX
Update Date : XXXX XX XXXX
Right:Enter Back:Return Exit:OK
Video Setup
White Balance
Spread Spectrum
Panel Select <XXXXX>
Reset TV-set
Factory Default
Right:Enter Back:Return Exit:OK
• This model uses the memory IC.
• This memory IC stores data for proper operation of the video and drive circuits.
• When replacing, be sure to use an IC containing this (initial value) data.
3.3.1 MEMORY IC REPLACEMENT PROCEDURE
1. Power off
Switch off the power and disconnect the power plug from the AC outlet.
2. Replace the memory IC
Be sure to use the memory IC written with the initial setting values.
3. Power on
Connect the power plug to the AC outlet and switch on the power.
4. Receiving channel setting
Refer to the OPERATING INSTRUCTIONS and set the receive channels (Channels Preset) as described.
5. User setting
Check the user setting items according to the given in page later. Where these do not agree, refer to the OPERATING
INSTRUCTIONS and set the items as described.
6. FACTORY MODE setting
Verify what to set in the FACTORY MODE, and set whatever is necessary.
3.3.2 FACTORY MODE SETTING
FACTORY MODE SCREENSETTING ITEM
FACTORY MODE SCREEN-1
Service
Hardware Ver : REV X.X
Sub MCU SW Ver : REV X.X
ATV SW Ver : XXXXXX X.XX.XX
DTV SW Ver : XXXXXX X.XX.XX
Sub MCU Loader Ver : XX.XX
DTV Loader Ver : XX.XX
ATV Loader Ver : X. X. X
System ID : XXXX.XXXX
Update Date : XXXX XX XXXX
Right:Enter Back:Return Exit:OK
Press [ ] key
FACTORY MODE SCREEN-2
Video Setup
White Balance
Spread Spectrum
Panel Select <XXXXX>
Reset TV-set
Factory Default
Right:Enter Back:Return Exit:OK
Setting itemsSettings
Video Setup[Do not adjust]
White BalanceAdjust
Spread Spectrum[Do not adjust]
Panel Select[Do not adjust]
Reset TV-set---
Factory Default---
1-12 (No.YA606<Rev.002>)
3.3.3 SETTINGS OF FACTORY SHIPMENT
3.3.3.1BUTTON OPERATION3.3.3.2REMOTE CONTROL DIRECT OPERATION
Setting itemSetting position
POWEROff
CHANNELPR1
VOLUME10
AVTV
3.3.3.3REMOTE CONTROL MENU OPERATION
(1) Picture
Setting itemSetting position
ModeBright
Fleshtone Off
Colour Temperature Cool
Noise Reduction High
Backlight High
(2) Sound
Setting itemSetting position
Bass0
Treble0
Balance0
AVLOn
Hyper SoundOff
(3) Install
Setting itemSetting position
CountryBJ MODEL: UK
BU/BD/ED91U MODEL: Germany
BN MODEL: Finland
BH MODEL: Netherland
Antenna PowerOff
Auto Search---
Manual Search---
Edit Channels---
Setting itemSetting position
CHANNELPR1
VOLUME10
ZOOMAUTO
SUB POWEROFF
(4) Feature
Setting itemSetting position
LanguageBJ MODEL: English
BU/BD/ED91U MODEL: German
BN MODEL: Finnish
BH MODEL: Dutch
Time Setting
Parental ControlDisable
OSD Transparency30
Blue BackOff
Power LampOn
4 : 3 Aspect SettingPanoramic
(5) APS (in Analog tV Mode only)
LanguageBJ MODEL: English
Antenna PowerOff
CountryBJ MODEL: UK
Channel Search---
Power On Time
Power Off Time
Auto Power Off
Setting itemSetting position
Off
Off
Off
BU/BD/ED91U MODEL: German
BN MODEL: Finnish
BH MODEL: Dutch
BU/BD/ED91 MODEL: Germany
BN MODEL: Finland
BH MODEL: Netherland
(No.YA606<Rev.002>)1-13
3.4REPLACEMENT OF CHIP COMPONENT
3.4.1 CAUTIONS
(1) Avoid heating for more than 3 seconds.
(2) Do not rub the electrodes and the resist parts of the pattern.
(3) When removing a chip part, melt the solder adequately.
(4) Do not reuse a chip part after removing it.
3.4.2 SOLDERING IRON
(1) Use a high insulation soldering iron with a thin pointed end of it.
(2) A 30w soldering iron is recommended for easily removing parts.
3.4.3 REPLACEMENT STEPS
1. How to remove Chip parts
2. How to install Chip parts
[Resistors, capacitors, etc.]
(1) As shown in the figure, push the part with tweezers and
alternately melt the solder at each end.
(2) Shift with the tweezers and remove the chip part.
[Transistors, diodes, variable resistors, etc.]
(1) Apply extra solder to each lead.
SOLDER
SOLDER
[Resistors, capacitors, etc.]
(1) Apply solder to the pattern as indicated in the figure.
(2) Grasp the chip part with tweezers and place it on the
solder. Then heat and melt the solder at both ends of the
chip part.
[Transistors, diodes, variable resistors, etc.]
(1) Apply solder to the pattern as indicated in the figure.
(2) Grasp the chip part with tweezers and place it on the
solder.
(3) First solder lead A as indicated in the figure.
(2) As shown in the figure, push the part with tweezers and
alternately melt the solder at each lead. Shift and remove
the chip part.
NOTE :
After removing the part, remove remaining solder from the
pattern.
1-14 (No.YA606<Rev.002>)
A
B
C
(4) Then solder leads B and C.
A
B
C
SECTION 4
Service
Hardware Ver : REV X.X
Sub MCU SW Ver : REV X.X
ATV SW Ver : XXXXXX X.XX.XX
DTV SW Ver : XXXXXX X.XX.XX
Sub MCU Loader Ver : XX.XX
DTV Loader Ver : XX.XX
ATV Loader Ver : X. X. X
System ID : XXXX.XXXX
Update Date : XXXX XX XXXX
Right:Enter Back:Return Exit:OK
Video Setup
White Balance
Spread Spectrum
Panel Select <XXXXX>
Reset TV-set
Factory Default
Right:Enter Back:Return Exit:OK
ADJUSTMENT
4.1ADJUSTMENT PREPARATION
(1) This TV is adjusted by using REMOTE CONTROL UNIT.
(2) The adjustment using the REMOTE CONTROL UNIT is made on the basis of the initial setting values. The setting values
which adjust the screen to the optimum condition can be different from the initial setting values.
(3) Make sure that connection is correctly made AC to AC power source.
(4) Turn on the power of the TV and measuring instruments for warming up for at least 30 minutes before starting adjustments.
(5) If the receive or input signal is not specified, use the most appropriate signal for adjustment.
(6) Never touch the parts (such as variable resistors, transformers and condensers) not shown in the adjustment items of this service
adjustment.
4.2 PRESET SETTING BEFORE ADJUSTMENTS
Unless otherwise specified in the adjustment items, preset the
following functions with the REMOTE CONTROL UNIT.
Setting itemSettings position
Picture ModeStandard
Colour Temperature Normal
4.4ADJUSTMENT ITEMS
VIDEO CIRCUIT
• WHITE BALANCE adjustment
4.5BASIC OPERATION OF FACTORY MODE
4.5.1 HOW TO ENTER THE FACTORY MODE
(1) Press [INFORMATION] key and [MUTING] key on the
remote control unit simultaneously to enter the FACTORY
MODE SCREEN-1. (Fig.4-1)
(2) Press [] key on the remote control unit simultaneously to
enter the FACTORY MODE SCREEN-2. (Fig.4-1)
4.5.2 HOW TO EXIT THE FACTORY MODE
Press the [OK] key to exit the factory mode.
4.3MEASURING INSTRUMENT AND FIXTURES
• Signal generator (Pattern generator)[PAL]
• Remote control unit
FACTORY MODE SCREEN-1
Service
Hardware Ver : REV X.X
Sub MCU SW Ver : REV X.X
ATV SW Ver : XXXXXX X.XX.XX
DTV SW Ver : XXXXXX X.XX.XX
Sub MCU Loader Ver : XX.XX
DTV Loader Ver : XX.XX
ATV Loader Ver : X. X. X
System ID : XXXX.XXXX
Update Date : XXXX XX XXXX
Right:Enter Back:Return Exit:OK
Press [ ] key
FACTORY MODE SCREEN-2
DO NOT ADJUST
Video Setup
White Balance
Spread Spectrum
Panel Select <XXXXX>
Reset TV-set
Factory Default
Right:Enter Back:Return Exit:OK
Fig.4-1
(No.YA606<Rev.002>)1-15
4.5.3 CHANGE AND MEMORY OF SETTING VALUE
SELECTION OF SETTING ITEM
• [FUNCTION /] key.
For scrolling up / down the setting items.
• [FUNCTION /] key.
For select the setting items.
CHANGE OF SETTING VALUE (DATA)
• [FUNCTION /] key.
For scrolling up / down the setting values.
MEMORY OF SETTING VALUE (DATA)
The setting value will be stored automatically when release the
REMOTE CONTROL UNIT keys.
4.5.4 FACTORY MODE SELECT KEY LOCATION
[MUTING] key
[INFORMATION] key
[MENU] key
[FUNCTION /] key
[Function/] key
4.6 SETTING ITEM IN THE FACTORY MODE
Swetting item
Brightness0 - 10041Adjust the Brightness value of Standard mode in Analog TV.
Contrast0 - 10068Adjust the Contrast value of Standard mode in Analog TV.
Standard
Bright
Video SetupRF(Analog TV)
Game
Soft
Sharpness0 - 10065Adjust the Sharpness value of Standard mode in Analog TV.
Colour0 - 10058Adjust the Colour value of Standard mode in Analog TV.
Farbton0 - 1000Adjust the Farbton value of Standard mode in Analog TV.
Brightness0 - 10041Adjust the Brightness value of Bright mode in Analog TV.
Contrast0 - 10073Adjust the Contrast value of Bright mode in Analog TV.
Sharpness0 - 10065Adjust the Sharpness value of Bright mode in Analog TV.
Colour0 - 10059Adjust the Colour value of Bright mode in Analog TV.
Farbton0 - 1000Adjust the Farbton value of Bright mode in Analog TV.
Brightness0 - 10043Adjust the Brightness value of Game mode in Analog TV.
Contrast0 - 10063Adjust the Contrast value of Game mode in Analog TV.
Sharpness0 - 10065Adjust the Sharpness value of Game mode in Analog TV.
Colour0 - 10058Adjust the Colour value of Game mode in Analog TV.
Farbton0 - 1000Adjust the Farbton value of Game mode in Analog TV.
Brightness0 - 10042Adjust the Brightness value of Soft mode in Analog TV.
Contrast0 - 10063Adjust the Contrast value of Soft mode in Analog TV.
Sharpness0 - 10065Adjust the Sharpness value of Soft mode in Analog TV.
Colour0 - 10058Adjust the Colour value of Soft mode in Analog TV.
Farbton0 - 1000Adjust the Farbton value of Soft mode in Analog TV.
Variable
range
Default
Value
Comment
1-16 (No.YA606<Rev.002>)
Video Setup
Video Setup
Swetting item
CVBS(EXT-4)
RGB(Digital TV
EXT-1 EXT-2)
Standard
Bright
Game
Soft
Standard
Bright
Game
Soft
Variable
range
Brightness0 - 10041Adjust the Brightness value of Standard mode in CVBS(EXT-4).
Contrast0 - 10068Adjust the Contrast value of Standard mode in CVBS(EXT-4).
Sharpness0 - 10065Adjust the Sharpness value of Standard mode in CVBS(EXT-4).
Colour0 - 10058Adjust the Colour value of Standard mode in CVBS(EXT-4).
Farbton0 - 1000Adjust the Farbton value of Standard mode in CVBS(EXT-4).
Brightness0 - 10041Adjust the Brightness value of Bright mode in CVBS(EXT-4).
Contrast0 - 10073Adjust the Contrast value of Bright mode in CVBS(EXT-4).
Sharpness0 - 10065Adjust the Sharpness value of Bright mode in CVBS(EXT-4).
Colour0 - 10059Adjust the Colour value of Bright mode in CVBS(EXT-4).
Farbton0 - 1000Adjust the Farbton value of Bright mode in CVBS(EXT-4).
Brightness0 - 10043Adjust the Brightness value of Bright mode in CVBS(EXT-4).
Contrast0 - 10063Adjust the Contrast value of Bright mode in CVBS(EXT-4).
Sharpness0 - 10065Adjust the Sharpness value of Bright mode in CVBS(EXT-4).
Colour0 - 10058Adjust the Colour value of Bright mode in CVBS(EXT-4).
Farbton0 - 1000Adjust the Farbton value of Bright mode in CVBS(EXT-4).
Brightness0 - 10042Adjust the Brightness value of Soft mode in CVBS(EXT-4).
Contrast0 - 10063Adjust the Contrast value of Soft mode in CVBS(EXT-4).
Sharpness0 - 10065Adjust the Sharpness value of Soft mode in CVBS(EXT-4).
Colour0 - 10058Adjust the Colour value of Soft mode in CVBS(EXT-4).
Farbton0 - 1000Adjust the Farbton value of Soft mode in CVBS(EXT-4).
Brightness0 - 10041Adjust the Brightness value of Standard mode in RGB(Digital TV EXT-1 EXT-2).
Contrast0 - 10068Adjust the Contrast value of Standard mode in RGB(Digital TV EXT-1 EXT-2).
Sharpness0 - 10065Adjust the Sharpness value of Standard mode in RGB(Digital TV EXT-1 EXT-2).
Colour0 - 10058Adjust the Colour value of Standard mode in RGB(Digital TV EXT-1 EXT-2).
Farbton0 - 1000Adjust the Farbton value of Standard mode in RGB(Digital TV EXT-1 EXT-2).
Brightness0 - 10041Adjust the Brightness value of Bright mode in RGB(Digital TV EXT-1 EXT-2).
Contrast0 - 10073Adjust the Contrast value of Bright mode in RGB(Digital TV EXT-1 EXT-2).
Sharpness0 - 10065Adjust the Sharpness value of Bright mode in RGB(Digital TV EXT-1 EXT-2).
Colour0 - 10059Adjust the Colour value of Bright mode in RGB(Digital TV EXT-1 EXT-2).
Farbton0 - 1000Adjust the Farbton value of Bright mode in RGB(Digital TV EXT-1 EXT-2).
Brightness0 - 10043Adjust the Brightness value of Game mode in RGB(Digital TV EXT-1 EXT-2).
Contrast0 - 10063Adjust the Contrast value of Game mode in RGB(Digital TV EXT-1 EXT-2).
Sharpness0 - 10065Adjust the Sharpness value of Game mode in RGB(Digital TV EXT-1 EXT-2).
Colour0 - 10058Adjust the Colour value of Game mode in RGB(Digital TV EXT-1 EXT-2).
Farbton0 - 1000Adjust the Farbton value of Game mode in RGB(Digital TV EXT-1 EXT-2).
Brightness0 - 10042Adjust the Brightness value of Soft mode in RGB(Digital TV EXT-1 EXT-2).
Contrast0 - 10063Adjust the Contrast value of Soft mode in RGB(Digital TV EXT-1 EXT-2).
Sharpness0 - 10065Adjust the Sharpness value of Soft mode in RGB(Digital TV EXT-1 EXT-2).
Colour0 - 10058Adjust the Colour value of Soft mode in RGB(Digital TV EXT-1 EXT-2).
Farbton0 - 1000Adjust the Farbton value of Soft mode in RGB(Digital TV EXT-1 EXT-2).
Default
Value
Comment
(No.YA606<Rev.002>)1-17
Swetting item
Video SetupYC(EXT-4S)
Video SetupCOMP(EXT-3)
Standard
Bright
Game
Soft
Standard
Bright
Game
Soft
Variable
range
Brightness0 - 10041Adjust the Brightness value of Standard mode in YC(EXT-4S).
Contrast0 - 10068Adjust the Contrast value of Standard mode in YC(EXT-4S).
Sharpness0 - 10065Adjust the Sharpness value of Standard mode in YC(EXT-4S).
Colour0 - 10058Adjust the Colour value of Standard mode in YC(EXT-4S).
Farbton0 - 1000Adjust the Farbton value of Standard mode in YC(EXT-4S).
Brightness0 - 10041Adjust the Brightness value of Bright mode in YC(EXT-4S).
Contrast0 - 10073Adjust the Contrast value of Bright mode in YC(EXT-4S).
Sharpness0 - 10065Adjust the Sharpness value of Bright mode in YC(EXT-4S).
Colour0 - 10059Adjust the Colour value of Bright mode in YC(EXT-4S).
Farbton0 - 1000Adjust the Farbton value of Bright mode in YC(EXT-4S).
Brightness0 - 10043Adjust the Brightness value of Game mode in YC(EXT-4S).
Contrast0 - 10063Adjust the Contrast value of Game mode in YC(EXT-4S).
Sharpness0 - 10065Adjust the Sharpness value of Game mode in YC(EXT-4S).
Colour0 - 10058Adjust the Colour value of Game mode in YC(EXT-4S).
Farbton0 - 1000Adjust the Farbton value of Game mode in YC(EXT-4S).
Brightness0 - 10042Adjust the Brightness value of Soft mode in YC(EXT-4S).
Contrast0 - 10063Adjust the Contrast value of Soft mode in YC(EXT-4S).
Sharpness0 - 10065Adjust the Sharpness value of Soft mode in YC(EXT-4S).
Colour0 - 10058Adjust the Colour value of Soft mode in YC(EXT-4S).
Farbton0 - 1000Adjust the Farbton value of Soft mode in YC(EXT-4S).
Brightness0 - 10049Adjust the Brightness value of Standard mode in COMP(EXT-3).
Contrast0 - 10070Adjust the Contrast value of Standard mode in COMP(EXT-3).
Sharpness0 - 10065Adjust the Sharpness value of Standard mode in COMP(EXT-3).
Colour0 - 10060Adjust the Colour value of Standard mode in COMP(EXT-3).
Farbton0 - 1000Adjust the Farbron value of Standard mode in COMP(EXT-3).
Brightness0 - 10049Adjust the Brightness value of Bright mode in COMP(EXT-3).
Contrast0 - 10077Adjust the Contrast value of Bright mode in COMP(EXT-3).
Sharpness0 - 10065Adjust the Sharpness value of Bright mode in COMP(EXT-3).
Colour0 - 10060Adjust the Colour value of Bright mode in COMP(EXT-3).
Farbton0 - 1000Adjust the Farbron value of Bright mode in COMP(EXT-3).
Brightness0 - 10051Adjust the Brightness value of Game mode in COMP(EXT-3).
Contrast0 - 10061Adjust the Contrast value of Game mode in COMP(EXT-3).
Sharpness0 - 10065Adjust the Sharpness value of Game mode in COMP(EXT-3).
Colour0 - 10060Adjust the Colour value of Game mode in COMP(EXT-3).
Farbton0 - 1000Adjust the Farbron value of Game mode in COMP(EXT-3).
Brightness0 - 10050Adjust the Brightness value of Soft mode in COMP(EXT-3).
Contrast0 - 10061Adjust the Contrast value of Soft mode in COMP(EXT-3).
Sharpness0 - 10065Adjust the Sharpness value of Soft mode in COMP(EXT-3).
Colour0 - 10060Adjust the Colour value of Soft mode in COMP(EXT-3).
Farbton0 - 1000Adjust the Farbron value of Soft mode in COMP(EXT-3).
Default
Value
Comment
1-18 (No.YA606<Rev.002>)
Video Setup
White Balance
Spread Spectrum
Reset TV-Set
Factory Default
Swetting item
Brightness0 - 10049Adjust the Brightness value of Standard mode in HDMI(EXT-5 EXT-6 EXT7)
Contrast0 - 10070Adjust the Contrast value of Standard mode in HDMI(EXT-5 EXT-6 EXT7)
Standard
Bright
HDMI(EXT-5
EXT-6 EXT7)
Game
Soft
Normal R0 - 10050Adjust Red value of Normal Colour Temperature.
Normal
Cool
Warm
SS EnableYes/NoYesTurn on or off the Spread Spectrum operation
SS Width0 - 10015Adjusting the Width of Spread Spectrum
SS Frequency0 - 100100Adjusting the frequency of Spread Spectrum
Initialize NVM From ROM
Press green key to contrinue...
Initialize the set------Initialize the set.
Normal G0 - 10031Adjust Green value of Normal Colour Temperature.
Normal B0 - 10026Adjust Blue value of Normal Colour Temperature.
Cool R0 - 10050Adjust Red value of Cool Colour Temperature.
Cool G0 - 10034Adjust Green value of Cool Colour Temperature.
Cool B0 - 10038Adjust Blue value of Cool Colour Temperature.
Warml R0 - 10039Adjust Red value of Warm Colour Temperature.
Warm G0 - 10024Adjust Green value of Warm Colour Temperature.
Warm B0 - 1000Adjust Blue value of Warm Colour Temperature.
Sharpness0 - 10065Adjust the Sharpness value of Standard mode in HDMI(EXT-5 EXT-6 EXT7)
Colour0 - 10060Adjust the Colour value of Standard mode in HDMI(EXT-5 EXT-6 EXT7)
Farbton0 - 1000Adjust the Farbton value of Standard mode in HDMI(EXT-5 EXT-6 EXT7)
Brightness0 - 10049Adjust the Brightness value of Bright mode in HDMI(EXT-5 EXT-6 EXT7)
Contrast0 - 10077Adjust the Contrast value of Bright mode in HDMI(EXT-5 EXT-6 EXT7)
Sharpness0 - 10065Adjust the Sharpness value of Bright mode in HDMI(EXT-5 EXT-6 EXT7)
Colour0 - 10060Adjust the Colour value of Bright mode in HDMI(EXT-5 EXT-6 EXT7)
Farbton0 - 1000Adjust the Farbton value of Bright mode in HDMI(EXT-5 EXT-6 EXT7)
Brightness0 - 10051Adjust the Brightness value of Game mode in HDMI(EXT-5 EXT-6 EXT7)
Contrast0 - 10061Adjust the Contrast value of Game mode in HDMI(EXT-5 EXT-6 EXT7)
Sharpness0 - 10065Adjust the Sharpness value of Game mode in HDMI(EXT-5 EXT-6 EXT7)
Colour0 - 10060Adjust the Colour value of Game mode in HDMI(EXT-5 EXT-6 EXT7)
Farbton0 - 1000Adjust the Farbton value of Game mode in HDMI(EXT-5 EXT-6 EXT7)
Brightness0 - 10050Adjust the Brightness value of Soft mode in HDMI(EXT-5 EXT-6 EXT7)
Contrast0 - 10061Adjust the Contrast value of Soft mode in HDMI(EXT-5 EXT-6 EXT7)
Sharpness0 - 10065Adjust the Sharpness value of Soft mode in HDMI(EXT-5 EXT-6 EXT7)
Colour0 - 10060Adjust the Colour value of Soft mode in HDMI(EXT-5 EXT-6 EXT7)
Farbton0 - 1000Adjust the Farbton value of Soft mode in HDMI(EXT-5 EXT-6 EXT7)
Variable
range
Default
Value
------Initialize Nvram data from ROM.
(When push green key it will start the initializing. When push back key it will
returns to previous.)
(When push right arrown key it will start the initializing. When push back key it
will returns to previous.)
Comment
(No.YA606<Rev.002>)1-19
4.7ADJUSTMENT PROCEDURE
4.7.1 VIDEO CIRCUIT
Item
WHITE
BALANCE
Measuring
instrument
Remote
control unit
Signal
generator
[WHITE BALANCE SETTING]
Setting ItemInitial setting value
Normal R
Normal G
Normal B
Test pointAdjustment partDescription
[White Balance]
Normal R
Normal G
Normal B
50
31
26
(1) Set COLOUR TEMP. to "Normal".
(2) Select "White Balance" from the FACTORY
MODE.
(3) Receive a PAL 75% all white signal.
(4) Set the setting values of <Normal R>,
<Normal G> and <Normal B> to the values in
the left table.
(5) Adjust the setting values of <Normal R> and
<Normal R> so that the screen becomes
maximum white.
NOTE:
When the normal mode is adjusted, other modes
(cool/ warm) are automatically adjusted.
SECTION 5
TROUBLESHOOTING
This service manual does not describe TROUBLESHOOTING.
Victor Company of Japan, Limited
Display category 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama-city, Kanagawa-prefecture, 221-8528, Japan
(No.YA606<Rev.002>)
Printed in Japan
VPT
PARTS LIST
CAUTION
J The parts identified by the symbol are important for the safety . Whenever replacing these parts, be sure to use specified ones to secure the
safety.
J The parts not indicated in this Parts List and those which are filled with lines --- in the Parts No. columns will not be supplied.
J P.W. BOARD Ass'y will not be supplied, but those which are filled with the Parts No. in the Parts No. columns will be supplied.
ABBREVIATIONS OF RESISTORS, CAPACITORS AND TOLERANCES
RESISTORSCAPACITORS
CRCarbon ResistorC CAP.Ceramic Capacitor
FRFusible ResistorE CAP.Electrolytic Capacitor
PRPlate ResistorM CAP.Mylar Capacitor
VRVariable ResistorCH CAP.Chip Capacitor
HV RHigh Voltage ResistorHV CAP.High Voltage Capacitor
MF RMetal Film ResistorMF CAP.Metalized Film Capacitor
OM RMetal Oxide Film ResistorPP CAP.Polypropylene Capacitor
CMF RCoating Metal Film ResistorPS CAP.Polystyrol Capacitor
UNF RNon-Flammable ResistorTF CAP.Thin Film Capacitor
CH V RChip Variable ResistorMPP CAP.Metalized Polypropylene Capacitor
CH MG RChip Metal Glazed ResistorTAN. CAP.Tantalum Capacitor
COMP. RComposition ResistorCH C CAP.Chip Ceramic Capacitor
LPTC RLinear Positive Temperature Coefficient ResistorBP E CAP.Bi-Polar Electrolytic Capacitor
CH AL E CAP.Chip Aluminum Electrolytic Capacitor
CH AL BP CAP.Chip Aluminum Bi-Polar Capacitor
CH TAN. E CAP.Chip Tantalum Electrolytic Capacitor
CH AL BP E CAP.Chip Tantalum Bi-Polar Electrolytic Capacitor
RESISTORS
FGJ KMNRHZ P
±1%±2%±5%±10%±20%±30%
+30%
-10%
+50%
-10%
+80%
-20%
+100%
-0%
(No.YA606<Rev.002>)3-1
CONTENTS
USING P.W. BOARD & REMOTE CONTROL UNIT ................................................................................................... 3-2
EXPLODED VIEW PARTS LIST ................................................................................................................................. 3-3
EXPLODED VIEW PARTS LIST ................................................................................................................................. 3-4
PACKING PARTS LIST ............................................................................................................................................. 3-23
USING P.W. BOARD & REMOTE CONTROL UNIT
P.W.B ASS'Y name
MAIN P.W.BHU-71200009←←HU-71200026←←
MPEG P.W.BHU-71200005←HU-71200006HU-71200005←HU-71200012
IR P.W.BHU-72200001←←←←←
KEY P.W.BHU-72200002←←←←←
C1HU-001060250C CAPACITOR0.1uF 16V K
C2HU-001060250C CAPACITOR0.1uF 16V K
C3HU-001060250C CAPACITOR0.1uF 16V K
C4HU-001060250C CAPACITOR0.1uF 16V K
C5HU-001060250C CAPACITOR0.1uF 16V K
C40HU-001060282C CAPACITOR6.8nF 50V K
C41HU-001060250C CAPACITOR0.1uF 16V K
C42HU-001060250C CAPACITOR0.1uF 16V K
C43HU-001060250C CAPACITOR0.1uF 16V K
C44HU-001060267C CAPACITOR68pF 50V J
C45HU-001060250C CAPACITOR0.1uF 16V K
C46HU-001060250C CAPACITOR0.1uF 16V K
C80HU-001060250C CAPACITOR0.1uF 16V K
C81HU-001060250C CAPACITOR0.1uF 16V K
C82HU-001060250C CAPACITOR0.1uF 16V K
C130HU-001071224E CAPACITOR220uF 16V
C131HU-001060250C CAPACITOR0.1uF 16V K
C132HU-001060250C CAPACITOR0.1uF 16V K
C133HU-001060250C CAPACITOR0.1uF 16V K
C134HU-001060219C CAPACITOR1000pF 50V K
C135HU-001071224E CAPACITOR220uF 16V
C136HU-001060250C CAPACITOR0.1uF 16V K
C137HU-001060219C CAPACITOR1000pF 50V K
C138HU-001060250C CAPACITOR0.1uF 16V K
C141HU-001071224E CAPACITOR220uF 16V
C142HU-001060250C CAPACITOR0.1uF 16V K
C143HU-001060219C CAPACITOR1000pF 50V K
C180HU-001060250C CAPACITOR0.1uF 16V K
C181HU-001060250C CAPACITOR0.1uF 16V K
C183HU-001060265C CAPACITOR1uF 16V K
C184HU-001060265C CAPACITOR1uF 16V K
C186HU-001060258C CAPACITOR30pF 50V J
C187HU-001060258C CAPACITOR30pF 50V J
C188HU-001060250C CAPACITOR0.1uF 16V K
C189HU-001060250C CAPACITOR0.1uF 16V K
C190HU-001060250C CAPACITOR0.1uF 16V K
C191HU-001060250C CAPACITOR0.1uF 16V K
C192HU-001060250C CAPACITOR0.1uF 16V K
C193HU-001060250C CAPACITOR0.1uF 16V K
C194HU-001060250C CAPACITOR0.1uF 16V K
C195HU-001060250C CAPACITOR0.1uF 16V K
C330HU-001060286C CAPACITOR10uF 10V
C331HU-001060250C CAPACITOR0.1uF 16V K
C332HU-001060250C CAPACITOR0.1uF 16V K
C333HU-001060250C CAPACITOR0.1uF 16V K
C334HU-001060250C CAPACITOR0.1uF 16V K
C335HU-001060250C CAPACITOR0.1uF 16V K
C336HU-001060250C CAPACITOR0.1uF 16V K
C337HU-001060250C CAPACITOR0.1uF 16V K
C338HU-001060286C CAPACITOR10uF 10V
C339HU-001060286C CAPACITOR10uF 10V
C340HU-001060286C CAPACITOR10uF 10V
C341HU-001060250C CAPACITOR0.1uF 16V K
C342HU-001060250C CAPACITOR0.1uF 16V K
C343HU-001060250C CAPACITOR0.1uF 16V K
CMOS 1-INPUT INVERTER
DUAL COMPARATOR
VOLTAGE DETECTOR
Ref No.Part No.Part NameDescription Local
C344HU-001060250C CAPACITOR0.1uF 16V K
C345HU-001060250C CAPACITOR0.1uF 16V K
C346HU-001060250C CAPACITOR0.1uF 16V K
C347HU-001060250C CAPACITOR0.1uF 16V K
C380HU-001060250C CAPACITOR0.1uF 16V K
C381HU-001060286C CAPACITOR10uF 10V
C382HU-001060219C CAPACITOR1000pF 50V K
C383HU-001060250C CAPACITOR0.1uF 16V K
C384HU-001060286C CAPACITOR10uF 10V
C385HU-001060219C CAPACITOR1000pF 50V K
C386HU-001060250C CAPACITOR0.1uF 16V K
C387HU-001060286C CAPACITOR10uF 10V
C388HU-001060219C CAPACITOR1000pF 50V K
C389HU-001060250C CAPACITOR0.1uF 16V K
C390HU-001060286C CAPACITOR10uF 10V
C430HU-001060250C CAPACITOR0.1uF 16V K
C431HU-001071221E CAPACITOR4.7uF 35V
C432HU-001060150C CAPACITOR1uF 25V
C433HU-001060250C CAPACITOR0.1uF 16V K
C434HU-001060250C CAPACITOR0.1uF 16V K
C435HU-001060219C CAPACITOR1000pF 50V K
C436HU-001060286C CAPACITOR10uF 10V
C437HU-001063090C CAPACITOR3.3pF 50V
C438HU-001060108C CAPACITOR0.01uF 50V
C480HU-001060250C CAPACITOR0.1uF 16V K
C481HU-001060250C CAPACITOR0.1uF 16V K
C482HU-001060286C CAPACITOR10uF 10V
C483HU-001060250C CAPACITOR0.1uF 16V K
C484HU-001060250C CAPACITOR0.1uF 16V K
C530HU-001060250C CAPACITOR0.1uF 16V K
C531HU-001060250C CAPACITOR0.1uF 16V K
C532HU-001060250C CAPACITOR0.1uF 16V K
C533HU-001060250C CAPACITOR0.1uF 16V K
C534HU-001060250C CAPACITOR0.1uF 16V K
C535HU-001060286C CAPACITOR10uF 10V
C536HU-001060250C CAPACITOR0.1uF 16V K
C537HU-001060250C CAPACITOR0.1uF 16V K
C538HU-001060250C CAPACITOR0.1uF 16V K
C539HU-001060250C CAPACITOR0.1uF 16V K
C540HU-001060250C CAPACITOR0.1uF 16V K
C541HU-001060286C CAPACITOR10uF 10V
C580HU-001060250C CAPACITOR0.1uF 16V K
C581HU-001071223E CAPACITOR100uF 16V
C582HU-001060250C CAPACITOR0.1uF 16V K
C583HU-001060250C CAPACITOR0.1uF 16V K
C585HU-001060221C CAPACITOR22pF 50V J
C587HU-001060221C CAPACITOR22pF 50V J
C589HU-001060221C CAPACITOR22pF 50V J
C591HU-001060221C CAPACITOR22pF 50V J
C700HU-001060250C CAPACITOR0.1uF 16V K
C701HU-001071223E CAPACITOR100uF 16V
C750HU-001071192E CAPACITOR10uF 25V
C751HU-001071192E CAPACITOR10uF 25V
C752HU-001060286C CAPACITOR10uF 10V
C753HU-001060250C CAPACITOR0.1uF 16V K
C754HU-001071192E CAPACITOR10uF 25V
C755HU-001071192E CAPACITOR10uF 25V
C756HU-001060250C CAPACITOR0.1uF 16V K
C757HU-001060250C CAPACITOR0.1uF 16V K
C802HU-001060286C CAPACITOR10uF 10V
C803HU-001071223E CAPACITOR100uF 16V
C804HU-001071223E CAPACITOR100uF 16V
C806HU-001060286C CAPACITOR10uF 10V
C807HU-001060286C CAPACITOR10uF 10V
C809HU-001071223E CAPACITOR100uF 16V
C810HU-001060286C CAPACITOR10uF 10V
C811HU-001060286C CAPACITOR10uF 10V
C812HU-001071223E CAPACITOR100uF 16V
C813HU-001060250C CAPACITOR0.1uF 16V K
C814HU-001060250C CAPACITOR0.1uF 16V K
C815HU-001060249C CAPACITOR100pF 50V J
C816HU-001071223E CAPACITOR100uF 16V
C817HU-001060250C CAPACITOR0.1uF 16V K
C819HU-001071223E CAPACITOR100uF 16V
C820HU-001060286C CAPACITOR10uF 10V
C821HU-001060286C CAPACITOR10uF 10V
C822HU-001071228E CAPACITOR470uF 16V
C823HU-001060250C CAPACITOR0.1uF 16V K
C824HU-001060250C CAPACITOR0.1uF 16V K
C900HU-001060250C CAPACITOR0.1uF 16V K
C901HU-001060250C CAPACITOR0.1uF 16V K
C902HU-001060250C CAPACITOR0.1uF 16V K
C903HU-001071194E CAPACITOR100uF 25V
C904HU-001071194E CAPACITOR100uF 25V
C905HU-001060250C CAPACITOR0.1uF 16V K
C906HU-001071194E CAPACITOR100uF 25V
C1HU-001060250C CAPACITOR0.1uF 16V K
C2HU-001060250C CAPACITOR0.1uF 16V K
C3HU-001060250C CAPACITOR0.1uF 16V K
C4HU-001060250C CAPACITOR0.1uF 16V K
C5HU-001060250C CAPACITOR0.1uF 16V K
C40HU-001060282C CAPACITOR6.8nF 50V K
C41HU-001060250C CAPACITOR0.1uF 16V K
C42HU-001060250C CAPACITOR0.1uF 16V K
C43HU-001060250C CAPACITOR0.1uF 16V K
C44HU-001060267C CAPACITOR68pF 50V J
C45HU-001060250C CAPACITOR0.1uF 16V K
C46HU-001060250C CAPACITOR0.1uF 16V K
C80HU-001060250C CAPACITOR0.1uF 16V K
C81HU-001060250C CAPACITOR0.1uF 16V K
C82HU-001060250C CAPACITOR0.1uF 16V K
C130HU-001071224E CAPACITOR220uF 16V
C131HU-001060250C CAPACITOR0.1uF 16V K
C132HU-001060250C CAPACITOR0.1uF 16V K
C133HU-001060250C CAPACITOR0.1uF 16V K
C134HU-001060219C CAPACITOR1000pF 50V K
C135HU-001071224E CAPACITOR220uF 16V
C136HU-001060250C CAPACITOR0.1uF 16V K
C137HU-001060219C CAPACITOR1000pF 50V K
C138HU-001060250C CAPACITOR0.1uF 16V K
C141HU-001071224E CAPACITOR220uF 16V
C142HU-001060250C CAPACITOR0.1uF 16V K
C143HU-001060219C CAPACITOR1000pF 50V K
C180HU-001060250C CAPACITOR0.1uF 16V K
C181HU-001060250C CAPACITOR0.1uF 16V K
C183HU-001060265C CAPACITOR1uF 16V K
C184HU-001060265C CAPACITOR1uF 16V K
C186HU-001060258C CAPACITOR30pF 50V J
C187HU-001060258C CAPACITOR30pF 50V J
C188HU-001060250C CAPACITOR0.1uF 16V K
C189HU-001060250C CAPACITOR0.1uF 16V K
C190HU-001060250C CAPACITOR0.1uF 16V K
C191HU-001060250C CAPACITOR0.1uF 16V K
C192HU-001060250C CAPACITOR0.1uF 16V K
C193HU-001060250C CAPACITOR0.1uF 16V K
C194HU-001060250C CAPACITOR0.1uF 16V K
CMOS 1-INPUT INVERTER
DUAL COMPARATOR
VOLTAGE DETECTOR
Ref No.Part No.Part NameDescription Local
C195HU-001060250C CAPACITOR0.1uF 16V K
C230HU-001060288C CAPACITOR1uF 25V
C231HU-001060265C CAPACITOR1uF 16V K
C232HU-001071228E CAPACITOR470uF 16V
C233HU-001060250C CAPACITOR0.1uF 16V K
C234HU-001060249C CAPACITOR100pF 50V J
C235HU-001071223E CAPACITOR100uF 16V
C236HU-001060250C CAPACITOR0.1uF 16V K
C237HU-001071223E CAPACITOR100uF 16V
C238HU-001060250C CAPACITOR0.1uF 16V K
C281HU-001071078E CAPACITOR220uF 50V
C282HU-001060026C CAPACITOR0.22uF 50V
C283HU-001060026C CAPACITOR0.22uF 50V
C284HU-001071078E CAPACITOR220uF 50V
C285HU-001071078E CAPACITOR220uF 50V
C286HU-001060026C CAPACITOR0.22uF 50V
C287HU-001060082C CAPACITOR0.1uF 50V
C288HU-001060001C CAPACITOR0.01uF 50V
C330HU-001060286C CAPACITOR10uF 10V
C331HU-001060250C CAPACITOR0.1uF 16V K
C332HU-001060250C CAPACITOR0.1uF 16V K
C333HU-001060250C CAPACITOR0.1uF 16V K
C334HU-001060250C CAPACITOR0.1uF 16V K
C335HU-001060250C CAPACITOR0.1uF 16V K
C336HU-001060250C CAPACITOR0.1uF 16V K
C337HU-001060250C CAPACITOR0.1uF 16V K
C338HU-001060286C CAPACITOR10uF 10V
C339HU-001060286C CAPACITOR10uF 10V
C340HU-001060286C CAPACITOR10uF 10V
C341HU-001060250C CAPACITOR0.1uF 16V K
C342HU-001060250C CAPACITOR0.1uF 16V K
C343HU-001060250C CAPACITOR0.1uF 16V K
C344HU-001060250C CAPACITOR0.1uF 16V K
C345HU-001060250C CAPACITOR0.1uF 16V K
C346HU-001060250C CAPACITOR0.1uF 16V K
C347HU-001060250C CAPACITOR0.1uF 16V K
C380HU-001060250C CAPACITOR0.1uF 16V K
C381HU-001060286C CAPACITOR10uF 10V
C382HU-001060219C CAPACITOR1000pF 50V K
C383HU-001060250C CAPACITOR0.1uF 16V K
C384HU-001060286C CAPACITOR10uF 10V
C385HU-001060219C CAPACITOR1000pF 50V K
C386HU-001060250C CAPACITOR0.1uF 16V K
C387HU-001060286C CAPACITOR10uF 10V
C388HU-001060219C CAPACITOR1000pF 50V K
C389HU-001060250C CAPACITOR0.1uF 16V K
C390HU-001060286C CAPACITOR10uF 10V
C430HU-001060250C CAPACITOR0.1uF 16V K
C431HU-001071221E CAPACITOR4.7uF 35V
C432HU-001060150C CAPACITOR1uF 25V
C433HU-001060250C CAPACITOR0.1uF 16V K
C434HU-001060250C CAPACITOR0.1uF 16V K
C435HU-001060219C CAPACITOR1000pF 50V K
C436HU-001060286C CAPACITOR10uF 10V
C437HU-001063090C CAPACITOR3.3pF 50V
C438HU-001060108C CAPACITOR0.01uF 50V
C480HU-001060250C CAPACITOR0.1uF 16V K
C481HU-001060250C CAPACITOR0.1uF 16V K
C482HU-001060286C CAPACITOR10uF 10V
C483HU-001060250C CAPACITOR0.1uF 16V K
C484HU-001060250C CAPACITOR0.1uF 16V K
C530HU-001060250C CAPACITOR0.1uF 16V K
C531HU-001060250C CAPACITOR0.1uF 16V K
C532HU-001060250C CAPACITOR0.1uF 16V K
C533HU-001060250C CAPACITOR0.1uF 16V K
C534HU-001060250C CAPACITOR0.1uF 16V K
C535HU-001060286C CAPACITOR10uF 10V
C536HU-001060250C CAPACITOR0.1uF 16V K
C537HU-001060250C CAPACITOR0.1uF 16V K
C538HU-001060250C CAPACITOR0.1uF 16V K
C539HU-001060250C CAPACITOR0.1uF 16V K
C540HU-001060250C CAPACITOR0.1uF 16V K
C541HU-001060286C CAPACITOR10uF 10V
C580HU-001060250C CAPACITOR0.1uF 16V K
C581HU-001071223E CAPACITOR100uF 16V
C582HU-001060250C CAPACITOR0.1uF 16V K
C583HU-001060250C CAPACITOR0.1uF 16V K
C585HU-001060221C CAPACITOR22pF 50V J
C587HU-001060221C CAPACITOR22pF 50V J
C589HU-001060221C CAPACITOR22pF 50V J
C591HU-001060221C CAPACITOR22pF 50V J
C700HU-001060250C CAPACITOR0.1uF 16V K
C701HU-001071223E CAPACITOR100uF 16V
C750HU-001071192E CAPACITOR10uF 25V
C751HU-001071192E CAPACITOR10uF 25V
C752HU-001060286C CAPACITOR10uF 10V
3-12(No.YA606<Rev.002>)
Ref No.Part No.Part NameDescription Local
Ref No.Part No.Part NameDescription Local
C753HU-001060250C CAPACITOR0.1uF 16V K
C754HU-001071192E CAPACITOR10uF 25V
C755HU-001071192E CAPACITOR10uF 25V
C756HU-001060250C CAPACITOR0.1uF 16V K
C757HU-001060250C CAPACITOR0.1uF 16V K
C802HU-001060286C CAPACITOR10uF 10V
C803HU-001071223E CAPACITOR100uF 16V
C804HU-001071223E CAPACITOR100uF 16V
C806HU-001060286C CAPACITOR10uF 10V
C807HU-001060286C CAPACITOR10uF 10V
C809HU-001071223E CAPACITOR100uF 16V
C810HU-001060286C CAPACITOR10uF 10V
C811HU-001060286C CAPACITOR10uF 10V
C812HU-001071223E CAPACITOR100uF 16V
C813HU-001060250C CAPACITOR0.1uF 16V K
C814HU-001060250C CAPACITOR0.1uF 16V K
C815HU-001060249C CAPACITOR100pF 50V J
C816HU-001071223E CAPACITOR100uF 16V
C817HU-001060250C CAPACITOR0.1uF 16V K
C819HU-001071223E CAPACITOR100uF 16V
C820HU-001060286C CAPACITOR10uF 10V
C821HU-001060286C CAPACITOR10uF 10V
C822HU-001071228E CAPACITOR470uF 16V
C823HU-001060250C CAPACITOR0.1uF 16V K
C824HU-001060250C CAPACITOR0.1uF 16V K
C900HU-001060250C CAPACITOR0.1uF 16V K
C901HU-001060250C CAPACITOR0.1uF 16V K
C902HU-001060250C CAPACITOR0.1uF 16V K
C903HU-001071194E CAPACITOR100uF 25V
C904HU-001071194E CAPACITOR100uF 25V
C905HU-001060250C CAPACITOR0.1uF 16V K
C906HU-001071194E CAPACITOR100uF 25V
REFER TO PARTS LIST IN PAGE 3-11 FOR THIS P.W. BOARD.
KEY P.W. BOARD ASS'Y (HU-72200002)
REFER TO PARTS LIST IN PAGE 3-11 FOR THIS P.W. BOARD.
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
(No.YA606<Rev.002>)3-21
PACKING
7
8910 11 12 13
2
3
6
4
5
1
PACKING PARTS LIST
Ref.No.Part No.Part NameDescriptionLocal
1HU-3070130001PK CARTON BOX
2HU-3071126001PS TOP CUSHION(L)
3HU-3071126002PS TOP CUSHION(R)
4HU-3071126003PSBOTTOM CUSHION(L)
5HU-3071126004PSBOTTOM CUSHION(R)
6HU-3072108002POLY BAG
9HU-2001100006SHEETLT-26DA9BJ
10------------WARRANTY-CARDHU-2030000004PT
11------------BATTERYAA/R6(x2)
12HU-0320200009REMOTE CONTROL UNIT RM-C1892B
12HU-0320200018REMOTE CONTROL UNIT RM-C1899SLT-26ED91U
13HU-2001100013CORRECTION SHEETLT-26DA9BN
The components identified by thesymbol and shading are
critical for safety. For continued safety replace safety ciritical
components only with manufactures recommended parts.
2.SPECIFIED VOLTAGE AND WAVEFORM VALUES
The voltage and waveform values have been measured under the
following conditions.
(1)Input signal: Colour bar signal
(2)Setting positions of
each knob/button and
variable resistor
(3)Internal resistance of tester
(4)Oscilloscope sweeping time
(5)Voltage values
Since the voltage values of signal circuit vary to some extent
according to adjustments, use them as reference values.
Composition resistor 1/2 [W] is specified as 1/2S or Comp.
(2)Capacitors
Capacitance value
1 or higher: [pF]
less than 1
Withstand voltage
No indication: DC50[V]
Others: DC withstand voltage [V]
AC indicated
Electrolytic Capacitors
47/50[Example]: Capacitance value [µF]/withstand voltage[V]
: [kΩ]
: [MΩ]
: Carbon resistor
: Oxide metal film resistor
: Metal film resistor
: Metal plate resistor
: Uninflammable resistor
: Fusible resistor
: [µF]
: AC withstand voltage [V]
(7)Ground symbol
: LIVE side ground
: ISOLATED(NEUTRAL) side ground
: EARTH ground
: DIGITAL ground
5.NOTE FOR REPAIRING SERVICE
This model's power circuit is partly different in the GND. The
difference of the GND is shown by the LIVE : ( ) side GND and the
ISOLATED(NEUTRAL) : ( ) side GND. Therefore, care must be
taken for the following points.
(1)Do not touch the LIVE side GND or the LIVE side GND and the
ISOLATED(NEUTRAL) side GND simultaneously. if the above
caution is not respected, an electric shock may be caused.
Therefore, make sure that the power cord is surely removed from
the receptacle when, for example, the chassis is pulled out.
(2)Do not short between the LIVE side GND and ISOLATED(NEUTRAL
side GND or never measure with a measuring apparatus measure
with a measuring apparatus ( oscilloscope, etc.) the LIVE side GND
and ISOLATED(NEUTRAL) side GND at the same time.
If the above precaution is not respected, a fuse or any parts will be broken.
Since the circuit diagram is a standard one, the circuit and
circuit constants may be subject to change for improvement
without any notice.
NOTE
Due improvement in performance, some part numbers show
in the circuit diagram may not agree with those indicated in
the part list.
When ordering parts, please use the numbers that appear
in the Parts List.
MAIN PWB P ATTERN .............................................................................................................................. 2-91
MPEG PWB P ATTERN............................................................................................................................. 2-95
IR PWB P ATTERN.................................................................................................................................... 2-99
KEY PWB P ATTERN ................................................................................................................................ 2-99
USING P.W. BOARD
P.W.B ASS㵭Y nameLT-26DA9BJ
MAIN P.W. BOARD
MPEG P.W. BOARD
IR P.W. BOARD
KEY P.W. BOARD
HU-71200009
HU-71200005
HU-72200001
HU-72200002
LT-26DA9BU
φ
φ
φ
φ
LT-26DB9BD
HU-71200006
SEMICONDUCTOR SHAPES
TRANSISTOR
BOTTOM VIEWFRONT VIEWTOP VIEW
CHIP TR
E
C
B
ECB
IC
BOTTOM VIEWFRONT VIEWTOP VIEW
OUT
E
IN
INOUTE
B
(G)E(S)C(D)
1N
ECB
ECB
1
1N
φ
φ
φ
C
BE
N
CHIP IC
N
1
2-2(No.YA606<Rev.001>)
TOP VIEW
1
N
WIRING DIAGRAM
LCD PANEL UNIT
[INVERTER PWB]
TOP
LCD PANEL UNIT
[LCD CONTROL PWB]
KEY PWB
TOP
DIGITAL TUNER
14
CN3
1
15
CN1
1
JP900
1
40
MPEG PWB
TOP
JP2
1
TOP
IR PWB
40
JP710
TOP
5
CN2
N
L
F1
250V/6.3A
POWER UNIT
15
JP680
1
5
JP681
1
6
JP682
1
1
31
JP630
1
ANALOG TUNER
JP1
AC INLET
1
6
JP581
4
1
MAIN PWB
SPEAKER(R)SPEAKER(L)
2-4(No.YA606<Rev.001>)(No.YA606<Rev.001>)2-3
BLOCK DIAGRAM
Component
SCART1
SCART2
Analog Tuner
SPDIF
(Optical)
HDMI
HDMI
HDMI
U770
SDPIF_OUT
HDMI1_PWR(HDMI1_DET)
HPD1
CEC_A
HDMI2_PWR(HDMI2_DET)
HPD2
CEC_A
HDMI3_PWR(HDMI3_DET)
HPD3
CEC_A
D1SDA/D1SCL
D2SDA/D2SCL
D3SDA/D3SCL
SCART1_ID
SCART1_R/G/B/CVBS
SCART1_FB
SCART1_RI/LI
SCART1_RO/LO
SCART1_CVBSO
SCART2_ID
SCART2_R/G/B/CVBS
SCART2_FB
SCART2_RI/LI
SCART2_RO/LO
SCART2_CVBSO
ANT_SIF
VCTP_SCL/SDA_3V3
(AT_SCL/SDA)
CVBS_TIN
TXD_PC/RXD_PC
EEPROM
TMDS1
TMDS2
TMDS3
Y470
X-TAL
14.318MHz
COMP_RI/LI
+5V_ANT
EEPROM
EEPROM
U660
RS232C
DRIVER
CEC_A
AL/AR_CVBS
U200
SWITCH
TA1/RA1_Sub MICOM
X-TAL
14.318
MHz
HDMI RECEIVER
COM_Pr/Y/Pb (MUX_RO/GO/BO)
U120
Analog MUX
SCART1_CVBSO
SCART2_CVBSO
VCTP_SCL/SDA_3V3
U771
REG
L/S
U470
+7V
ANT_PWR_EN
TA2/RA2TA1/RA1
SCART_R/G/B/CVBS
U580
(OP AMP)
MSP_ENABLEU630
RS232_SW
U661
COM_RXD/TXD
MPEG_RXD/TXD
COMU_RX/TX
HDMI_RESET
V
CTP_SCL/SDA_3V3
RGB(24Bits)
HDMI_INT
HSYNC/VSYNC
IN0DE
IN0CLK
HDMI_I2SHDMI_AUD_R/L
MUX_AUD_R/L
SELECTION1
SCART_FB
SCART_RI/LI
U560
AUDIO DAC+OP
AMP
CVBS_TIN
ANT_SIF
SCART1_RO/LO
SCART1_CVBS_OUT
SCART2_CVBS_OUT
SCART2_RO/LO
+5V+8V ,
VCTP_SCL/SDA_3V3
HPD1
HPD2
HPD3
HDMI1_DET
HDMI2_DET
HDMI3_DET
187/184/182Pin
MPEG_GPIO
178/177/176/189Pin
VSUP5.0SIF,
VSUP8.0AU
115,116Pin
208Pin
1Pin
159Pin
160Pin
2Pin
100Pin
109Pin
171,47Pin
48Pin
49Pin
11/12Pin
101Pin
13,14Pin
3Pin
191Pin
31Pin
175Pin
9/10Pin
23/24Pin
195Pin
194Pin
21/22Pin
EEPROM
P2.6
P2.7
P4.7
P4.6
P1.7
P1.6
P4.5
P3.7
P3.1
50 ~ 73 Pin
DIGITAL VIDEO INPUT PORT
89Pin
P2.2
VIN22/DVS
DEN
DCLK
AIN2R/L
VIN6/7/9
P3.5
AIN3R/L
P4.4
VIN1
SIFIN+
VIN15/16/17/3
VIN18
AIN1R/L
AOUT1R/L
VOUT1
VOUT2
AOUT2R/L
RESETQ
8Pin
/RESET
MCP100T
VSUP3.3COM
83/84Pin
SCL/SDA
ROM_WP
105Pin
P3.3
U1
SCALER
COM_RXD/TXD
91/92Pin
P2.5/TMS
P2.4/TDI
MPEG_R_Pr/G_Y/B_Pb
MPEG_CVBS
181,180,
179Pin
190Pin
VIN11/12/13
VIN2
OSDR/
P3.0
OSDFW
P3.2
P3.4
P2.1
P2.0
P4.1
P1.1
P1.4
P1.5
P1.2
P2.3
P4.3
P4.2
P3.6
VIN19/20
VIN21
AIN4L/R
HEADPHONEL/R
SPEAKERR
SPEAKERL
P4.0
XTAL
JTAG
Debeg
VCTP_SCL/SDA_3V3
110Pin
R,C
98Pin
filter
106Pin
102Pin
88Pin
87Pin
117Pin
167Pin
ANT_PWR_CTRL
162Pin
161Pin
166Pin
90Pin
119Pin
BRT_ADJ
120Pin
99Pin
173/174Pin
172Pin
15,16Pin
DTT_AUD_R/L
25/26Pin
HP_L/R
27Pin
R_SPK
28Pin
L_SPK
118Pin
MUTE_CTRL
Y60
X-TAL
20.25MHz
MPEG_RXD/TXD
OSDFW
SECAM-L
ANT_PWR_EN
DEBUG
RS232_SW
VCTP_Fail
SBTV
DTT_RESET
VCTP_INT
PANEL_PWR
BLT_EN
MPEG_B_Pb
MPEG_G_Y
MPEG_R_Pr
MPEG_CVBS
SPDIF_OUT
COMU_RX/TX
L/S
TA1/RA1_Sub MICOM
LVDS_OUT
HEADPHONE_ID
SV_C/Y
(AUDIO AMP)
MSP_ENABLE
IR_SCART_TV
CVBS
OP AMP
U580
AC_DETECT
SCL/SDA_STB
VCTP_INT
VCTP_Fail
+12V or +5V
MPEG PWB
STBY_EN
+5VST
+5V
+7V
+12V
AC_DETECT
U2
AL/AR_CVBS
BRT_ADJ
BLT_EN
HPO_L/R
POWER
AMP_R-
AMP_R+
U801
MICOM
AMP_L-
AMP_L+
DTT_RESETDTT_AUD_R/L
MPEG_GPIO
IR_SCART_TV
POWER UNIT
LCD
PANEL
UNIT
SBTV
VOLTAGE
FRONT_LED_B
LED_R
KEY_ADC1
KEY_ADC2
IR_IN
Y800
X-TAL
16.0MHz
+24V
SPEAKER(R)
SPEAKER(L)
U800
DET
+5VSTRESETn
LED&KEY PWB
(No.YA606<Rev.001>)2-52-6(No.YA606<Rev.001>)
CIRCUIT DIAGRAMS
MAIN PWB CIRCUIT DIAGRAM (1/22) [Analog Tuner]
DD
5
U770
TAUT-S711D
Input - IEC type
L/T outpur Phono type
BB(CTR)
ANT (5V)
12345
4
I2C AS : 0xC0
+B(+5V)NCRF_AGC
TP_+33VNCGND
SDA
SCLASNC
67891011121314151617181920
CVBS
AFT
AUDIO
SIFNCNCNCNC
GND1
GND2
GND3
GND4
3
24
23
22
21
2
1
C773
R770000/1005
R779000/1005
+5V_ANT
C774
104p/1005
C781
330p
106p/2012
R780
750/F/1005
C777
+7V
+5V_ANT
AGC
+5V_Analog_Tuner
C771
R785
CC
MAIN PWB
(3/22)
BB
152/1005
SECAM-L
R784
101/1005
MAIN PWB(3/22)
1
OPEN_2.2uF/50V/MVK/S
Q773
KST4401
23
ANT_PWR_EN
ANT_PWR_CTRL
103/1005
C780
2.2uF/50V/MVK/S
C770
104p/1005
+3V3D
R781
IF ANT_PWR_CTRL is L --> ANT_PWR_EN L
R778
OPEN_103/1005
AGC
R773
472/1005
+5V_Analog_Tuner
C772
470uF/16V/MVK/S
8
7
6
+5V_ANT_A
106p/2012
U772
POWER SW MIC2544-1YMM
1
EN
2
3
45
OUT
FLG
OUT
GND
NCILIM
152/1005
IN
R789
ANT_SIF
CVBS_TIN
R776330/1005
R777
C782
330p
C778
104p/1005
MAIN PWB(4/22)
330/1005
C783
1
/INH
OPEN-000/1005
R790
000/1005
R791
000/1005
R792
R793
C784
OPEN-330pOPEN-330p
U771
LD29150PT/P-PAK 5P
MAX 1.5A
VIN
GND
VOUT
ADJ
GND
2
3
456
R786
333/F/1005
R787
103/F/1005
OPEN-000/1005
C779
101p/1005
C775
106p/2012
C776
104p
VCTP_SCL_3V3
VCTP_SDA_3V3
+5.29V
+5V_ANT_A
D770
OPEN-ZMMC5V6
12
MAIN PWB(3/22),(6/22),(13/22),(21/22)
ANT_PWR_EN
+5V_ANT
ONHIGH
LOW
OFF
MAIN PWB ASS'Y (1/22)
AA
[Analog Tuner]
HU-71200009
All location are from 770 to 799
5
4
3
2
1
lt-26da9bj_scaler-20_0529_20/23_0.0
2-8(No.YA606<Rev.001>)(No.YA606<Rev.001>)2-7
MAIN PWB CIRCUIT DIAGRAM (2/22) [VCTP Power]
1
2
3
4
5
6
VCT-P POWER
L2
BLM18PG300SN1D
DD
AC231
CC
27mm
27*27*12(AL 6063S-T5)
+3V3_VCTP
27mm
L11
BLM18PG300SN1D
+3V3_VCTP
C30
102p/1005
BLM18PG300SN1D
BLM18PG300SN1D
C3
106p/2012
L5
C13C16
106p/2012
L8
C21
106p/2012
C32
104p/1005
VSUP3.3DIG+3V3_VCTP
C4
104p/1005
VSUP3.3FL
104p/1005
VSUP3.3COM+3V3_VCTP
C22
104p/1005
VSUP3.3LVDS
C14
+3V3_VCTP
+3V3_VCTP
+3V3_VCTP
L3
BLM18PG300SN1D
C5
106p/2012
L6
BLM18PG300SN1D
C15
106p/2012
L9
BLM18PG300SN1D
C23
106p/2012
L12
BLM18PG300SN1D
VSUP3.3IO1
C6
104p/1005104p/1005
VSUP3.3DRI
104p/1005
VSUP3.3RAM
C24
104p/1005
C7
+3V3_VCTP
+3V3_VCTP
+3V3_VCTP
L4
BLM18PG300SN1D
C8
106p/2012
L7
BLM18PG300SN1D
C17
106p/2012
L10
BLM18PG300SN1D
C25
106p/2012
L13
BLM18PG300SN1D
VSUP3.3FE+3V3_VCTP
104p/1005
VSUP3.3VO
104p/1005
VSUP3.3IO3
C26
104p/1005
VSUP3.3DAC
C9
C18
+12V
R1471/1005
R2
R3
R4
+1V8_VCTPVSUP1.8FEVSUP1.8LVDS+1V8_VCTP
HH-1M3216-501JT
471/1005
471/1005
471/1005
ZMM5237B
C19
106p/2012
L14
D1
12
VSUP1.8DIG+1V8_VCTP_A
VSUP8.0AU
C20
104p/1005
C11
104p/1005
C12
101p/1005
C10
106p/3216
C27
104p/1005
BB
C28
106p/2012
VSUP3.3IO3
VSUP3.3VO
197
192
VSUP3.3IO3
C29
106p/2012
VSUP1.8FE
VSUP3.3FE
VSUP3.3DAC
185
169
170
164
VSUP1.8FE
VSUP1.8FE
VSUP3.3FE
VSUP3.3VO
VSUP3.3LVDS
133
139
150
156
VSUP3.3DAC
VSUP3.3LVDS
VSUP3.3LVDS
VSUP3.3LVDS
VSUP3.3LVDS
C31
102p/1005
VSUP1.8LVDS
VSUP1.8DIG
VSUP3.3IO1
VSUP3.3FL
127
142
124
1149686
VSUP3.3IO1
VSUP1.8DIG
VSUP3.3LVDS
VSUP1.8LVDS
VSUP3.3DRI
VSUP3.3COM
77
VSUP3.3FL
VSUP3.3IO1
VSUP3.3COM
C33
104p/1005
VSUP3.3RAM
VSUP3.3DIG
VSUP5.0SIF
7545363318
VSUP3.3DRI
VSUP3.3DIG
VSUP3.3RAM
C34
104p/1005
VSUP8.0AU_A
VSUP8.0AU
VSUP5.0SIF
17
VREFAU
C43
104p/1005
+5V
C42
106p/2012
C35
106p/2012
VSUP5.0SIF
L16
BLM31PG121SN1L
C44
106p/3216
C46
106p/3216
C45
104p
C36
104p/1005
8
1
C37
106p/2012
VSUP8.0AU_A
6
7
D2
D1
D1
S1
G1
S2
G2D2
2
3
45
106p/3216
U2
SI4925DY
C47
VSUP8.0AU
L15
BLM31PG121SN1L
C38
104p/1005
Sequence : STBY_EN --> +3V3_VCTP --> MSP_ENABLE
R6
104/1005
MSP_ENABLEHON
C39
106p/2012
C40
C41
104p/1005104p/1005
LOFF
Q1
U1D
VCT7993P-FA-A1-H-500
AA
IC_GND
209
GND3.3IO3
GND3.3DAC
GND3.3LVDS
196
163
153
GND3.3LVDS
GND3.3LVDS
GND3.3LVDS
GND3.3LVDS
147
144
136
130
GND1.8DIG
GND3.3IO1
GND3.3IO1
123
113958576744635342019186
GND3.3FL
GND3.3COM
GND3.3DRI
GND3.3RAM
GND3.3DIG
GNDA
SGND
GNDA
GNDA
REXT
143
R5
622/F/1005
KST4401
1
R7472/1005
23
MSP_ENABLE
MAIN PWB(21/22)
All location are from 1 to 59.
1
MAIN PWB ASS'Y (2/22)
[VCTP Power]
HU-71200009
2
(No.YA606<Rev.001>)2-92-10(No.YA606<Rev.001>)
3
4
5
6
lt-26da9bj_scaler-01_0529_1/23_0.0
MAIN PWB CIRCUIT DIAGRAM (3/22) [VCTP Reset & GPIO]