JVC BR-DV6000E User Manual

DV VIDEO CASSETTE RECORDER DV VIDEOKASSETTENREKORDER ENREGISTREUR A CASSETTE DIGITAL VIDEO DV VIDEOREGISTRATORE UNIDAD GRABADORA DE VÍDEO DV

INSTRUCTION MANUAL

BR-DV6000E

MENU RESET

Mini

SEARCH–

MIC

HOLD

PHONES REC LEVEL

DISP

SET SEARCH+

BLANK CUE UP

CH-1/3 CH-2/4

PROFESSIONAL

BR-DV6000

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

ISTRUZIONI PER L’USO

MANUAL DE INSTRUCCIONES

OPERATE

REC

PLAY PAUSE

A.DUB

REW STOP FF

EJECT

AUDIO INPUT

COUNTER

CTL L

SELECT

MONITOR OUTPUT REMOTE

CH-1/2

MIX

LINE

CH-3/4

Y/C

(CPN)

LOCAL

EnglishItaliano Español Français Deutsch

Thank you for purchasing this JVC product. Before operating this unit, please read the instructions carefully to unsure the best possible performance.

LLT0034-002B-H

Supplement

This equipment is in conformity with the provisions and protection requirements of the corresponding European Directives. This equipment is designed for professional video appliances and can be used in the following environments:

Residential (including both of the location type class 1 and 2 found in IEC 1000-2-5)

Commercial and light industrial (including, for example, theatres)

Urban outdoors (based on the definition of location type class 6 in IEC 1000-2-5)

This apparatus is designed for rack mounting or is used close to other apparatus.

In order to keep the best performance and furthermore for electromagnetic compatibility we recommend to use cables not exceeding the following lengths:

Port Cable Length

LINE IN Coaxial Cable 10 meters LINE OUT Coaxial Cable 10 meters VIDEO MONITOR OUT Coaxial Cable 10 meters COMPONENT Y IN Coaxial Cable 10 meters R-Y IN Coaxial Cable 10 meters B-Y IN Coaxial Cable 10 meters COMPONENT Y OUT Coaxial Cable 10 meters R-Y OUT Coaxial Cable 10 meters B-Y OUT Coaxial Cable 10 meters Y/C IN Exclusive Cable 10 meters Y/C OUT Exclusive Cable 10 meters SYNC IN Coaxial Cable 10 meters TIMECODE IN Coaxial Cable 10 meters TIMECODE OUT Coaxial Cable 10 meters AUDIO IN Exclusive Cable 10 meters AUDIO OUT Exclusive Cable 10 meters AUDIO MONITOR OUT Exclusive Cable 10 meters SERIAL REMOTE Cable with RM-G30 2 meters REMOTE1(RS-422) Exclusive Cable 5 meters REMOTE2(JVC BUS) Exclusive Cable 10 meters DV IN/OUT Exclusive Cable 4 meters MIC Cable with Microphone 5 meters PHONES Cable with Headphones 5 meters XLR AUDIO Exclusive Cable 10 meters DC 12V Exclusive Cable 1.9 meters

The inrush current of this apparatus is 11.5 amperes.

Caution:

5 Where there are strong electromagnetic waves or magnetism, for example near a radio or TV

transmitter, transformer, motor, etc., the picture and sound may be disturbed. In such a case, please keep the apparatus away from the sources of the disturbance.

5 When the RM-G800 remote controller is used, the counter, etc. may malfunction due to inter-

ference generated by the peripheral equipment. In this case, consult your nearest JVC dealer.

E-2

SAFETY PRECAUTIONS

Warning Notice

FOR YOUR SAFETY (Australia)

1. Insert this plug only into effectively earthed three-pin power outlet.

2. If any doubt exists regarding the earthing, consult a qualified electrician.

3. Extension cord, if used, must be three-core correctly wired.

IMPORTANT (In the United Kingdom)

Mains Supply (AC 230 V

WARNING – THIS APPARATUS

MUST BE EARTHED

The wires in this mains lead are coloured in accordance with the following code;

GREEN-and-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured GREEN-ANDYELLOW must be connected to the terminal in the plug which is marked with the letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or which is coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

POWER SYSTEM Connection to the mains supply

This unit operates on voltage of 220 V to 240 V AC, 50 Hz/60 Hz.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

To prevent electric shock, do not open the cabinet. No user serviceable parts inside. Refer servicing to qualified service personnel.

Note:

The rating plate and the safety caution are on the rear of the unit.

The OPERATE button does not completely shut off mains power from the unit, but switches operating current on and off.

WARNING

It should be noted that it may be unlawful to rerecord pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast, or cable programme and in any literary, dramatic, musical or artistic work embodied therein.

Caution for AC Mains Lead

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This product is equipped with 2 types of AC cable. One is for continental Europe, etc. and the other one is only for U.K. Appropriate mains cable must be used in each local area, since the other type of mains cable is not suitable.

FOR CONTINENTAL EUROPE, ETC.

Not to be used in the U.K.

FOR U.K. ONLY

If the plug supplied is not suitable for your socket outlet, it should be cut off and appropriate one fitted.

E-3

Thank you for purchasing our

DV Video Cassette Recorder

BR-DV6000.

As this is a DV-format video cassette recorder, video cassettes with the or logo can be used with it. DVCAM cassettes can be recorded in the DV format.

● In order to prevent crumpling due to tape slack, do not perform important recording within the first and last 2 – 3 minute-run of the tape.

● Recorded video (sound) is meant for personal entertainment only and must not be used for other purposes without the prior consent of the copyright owner.

● JVC shall not guarantee the quality of recording and playback should BR-DV6000 fail to function normally due to defects, either of the unit itself or the video cassette tapes.

MAIN FEATURES

● DV format

High picture and sound quality by digital technology.

● Compatible mechanisms for standard/mini DV cas-

sette tapes

It records on and plays back DV cassette tapes of the standard and mini size. (SP mode only) Recording in the DV format can be performed on DVCAM cassette tapes.

● Tapes recorded in DVCAM format can be played

back on the BR-DV6000, detection is automatic.

● Equipped with composite, component and Y/C in-

put & output terminals.

● Equipped with DV IN/OUT terminals. (IEEE1394)

It can exchange digital signals with IEEE1394-compatible devices.

● Both NTSC and PAL signals supported

Playing back NTSC tapes or recording NTSC signals from the DV input is possible on the BR-DV6000E. Please select NTSC on PB/DV IN menu. For analog signal input, only PAL is supported.

● RS-422A and JVC bus interface supported

RS-422A-compatible edit controller RM-G820 and JVC bus-compatible edit controller RM-G800 can be used for editing.

● Optionally, the RS-232C interface can be used.

● Recording and playback of time codes

● Time code I/O terminal

Slave lock is allowed if BR-DV6000 is connected to an external time code generator.

● SYNC IN terminal

External synchronization signals can be input.

● Audio-dubbing function (after-recording)

If the sampling frequency is 32kHz, audio dubbing can be performed into CH3 and CH4 (except during DV input).

● Backup recording function

With the combined use of other DV machines, long-time continuous recording is possible.

● Using the SERIAL REMOTE OUT terminal or DV ter-

minal, dubbing with other recorders is possible only with playback operation by BR-DV6000. (Replication function)

● Equipped with a 2.5-inch color LCD

Images, status display and menu display can be viewed.

● Multi-cue up

Up to 5 points of the tape position can be registered and cued up.

● Index/blank search function

It can search for positions where index signals are recorded and unrecorded parts.

● Repeat play function

There are 3 types of repeat function. (INDEX/ VIDEO END/ TAPE END)

● Recording/playback with an external timer

● With the use of the network board SA-DV6000 (sold

separately), image and audio streaming data can be recorded on a CF card, and with a LAN card, streaming data can be transmitted to a PC.

● With the XLR IN board SA-X61U or XLR OUT board

SA-X62U (sold separately), audio input/output via the XLR terminal is possible.

E-4

Table of Contents

INTRODUCTION

Remarks of usage ......................................... 6

Regular maintenance .................................... 7

Cleaning tape ................................................ 8

Cassette tape ................................................ 8

Condensation ................................................ 9

NAMES AND FUNCTIONS OF PARTS

Front panel .................................................. 10

Rear panel ................................................... 16

ON-SCREEN DISPLAY

On-screen display ....................................... 20

Status display .............................................. 21

Status/Event display .................................... 23

Alarm display ............................................... 24

LCD display ................................................. 26

CONNECTION

Connecting video signals ............................ 28

Connecting audio signals ............................ 30

Connecting to editing system ...................... 32

Connecting with serial remote terminals ..... 34

Connecting the AC adapter ......................... 35

PREPARATION

Tu r ning on/off the power .............................. 36

Operation method (main unit/remote

controller) and operation lock mode ............ 37

Loading/Ejecting cassette ........................... 38

Setting the LCD display ............................... 39

Setting/Displaying date and time ................. 40

RECORDING

Setting ......................................................... 42

Recording procedure ................................... 43

Audio dubbing ............................................. 44

Backup recording function ........................... 45

Recording with serial remote terminals ....... 46

External timer recording .............................. 47

PLAYBACK

Setting ......................................................... 48

Basic playback procedure ........................... 49

Special playback functions .......................... 50

Search function ........................................... 52

Repeat playback.......................................... 53

Multi cue-up ................................................. 54

External timer playback ............................... 56

Dubbing with another machine using the

SERIAL REMOTE OUT/DV terminals ......... 57

TIME CODE

Displaying the time code ............................. 58

Presetting the time code ............................. 59

Recording the time code ............................. 60

Playing back the time code ......................... 63

EDIT

Editing with an RS-422A/JVC bus edit

remote controller ......................................... 64

Using a non-linear editing system ............... 68

MENU SCREENS

Structure of the Menu screens .................... 69

Setting the menus ....................................... 70

Description of the Menu screens ................. 72

RS-232C INTERFACE

Command tables ......................................... 84

RS-232C specifications ............................... 85

RS-232C commands ................................... 86

OTHERS

Warning display ........................................... 97

Troubleshooting ........................................... 99

Checking the hour meter ........................... 100

Optional devices ........................................ 101

Installing SA-K46U RS-232C interface

board ......................................................... 102

Specifications ............................................ 103

E-5

INTRODUCTION

Remarks of usage

䡵 Place of storage and use

Avoid storing or using this VCR in the following places:

● Excessively hot or cold places beyond the allowable temperature for operation (5˚C – 40˚C).

● Humid or dry places beyond the allowable humidity range for operation (30% – 80% RH).

● Dusty or sandy places.

● Places exposed to oil, smoke or steam, such

as the kitchen vicinity.

● Intensely vibrating or unstable places.

● Places prone to condensation.

● Places that generate strong magnetic fields,

e.g., near a transformer or motor.

● Places near devices that generate electric waves, e.g., a transceiver or mobile phone.

● Places that generate X-ray radiation or corrosive gases.

䡵 Handling the unit

● Do not place heavy objects on the unit, like a

monitor or TV.

● Do not insert foreign objects into the cassette slot.

● Mind your finger when loading a cassette tape. Be careful not to get your fingers clamped when loading the cassette to prevent injury.

● Place this unit out of reach of young children to prevent injury as fingers may get clamped while a cassette tape is being loaded.

● Do not block the ventilation openings.

● Avoid strong impact to the unit. Do not drop

the unit.

● Remove the cassette tape from the cassette slot when transporting the unit.

● Remove the AC adapter to save energy when the unit is not in use.

䡵 Maintaining the unit (Turn off the power

before performing maintenance work.)

Wipe the unit with a soft cloth. Do not wipe it with thinner or benzene as it may melt or tarnish the unit surface. For stubborn stains, use water-diluted neutral detergent and then wipe it dry.

䡵 Use the supplied AC adapter to connect

the unit to a power source.

䡵 Use the supplied power cord.

Using a different type or damaged cord may cause fire or electric shock.

䡵 Do not use the supplied power cord for

other models.

䡵 LCD screen

The LCD screen is designed and manufactured with high-precision technology. Minute black dots may appear or bright (red, blue and white) dots are permanently lit. This phenomenon is not a product defect and the dots are not recorded.

E-6

Regular maintenance

This unit uses consumables or components that will wear off. If a worn-out or deteriorated component continues to be used, it may cause the unit to break down. To prevent this, perform routine maintenance using the head-cleaning tape. With the head-cleaning tape alone, however, the entire tape-winding mechanism cannot be completely cleaned. Perform regular maintenance of the components as shown below.

䡵 Regular maintenance

The tasks of maintenance involved are similar to that of replacing the engine oil or tire of a car.

Depending on the number of usage hours, inspect or replace the components as follows:

Number of hours 500H 1000H 1500H 2000H 4000H

Drum assembly (including head)

Head cleaner 夡䢇夡䢇䢇

Tape guide, roller 䡬夡夡䢇䢇

Reel disk, tension bands — 夡 — 䢇䢇

䡬䡬䡬䢇䢇

—: Inspection

䡬 : Cleaning, inspection and

adjustment

夡 : Cleaning and inspection;

Replacement if necessary

䢇 : Replacement

Work and frequency of maintenance depend on the environment and usage. The above information serves only as a guide.

Usage Time :You can check the drum usage time with the hour meter display.

For details, refer to page 100, “Checking the hour meter.”

Maintenance consultation :For details on the maintenance plan and fee, consult with your

JVC-authorized service agent.

䡵 Head cleaning

• Recording or playing back with a dirty head will result in block noise or disrupted sound. Perform regular head cleaning to maintain superior image and sound quality.

Block Noise

•For information on how to use the head cleaning tape and the relevant remarks, refer to page 8, “Cleaning tape”.

• If the head is dusty, “HEAD CLEANING REQUIRED!” will be displayed on the monitor when this unit plays a tape.

HEAD CLEANING REQUIRED!

E-7

INTRODUCTION

Cleaning tape

Use a JVC cleaning tape. Follow the instructions below for using the cleaning tape.

Run the tape for 10 seconds in the PLAY mode. (Thereafter, it stops automatically and enters the STOP mode.)

• After loading the cleaning tape, press the PLAY button.

For a single cleaning session, it can be repeated up to 4 times.

Refer to the following table as a guide for cleaning.

Notes

● Under low humidity conditions, (10% RH to 30% RH), perform head cleaning at intervals of half of the periods stated in the table.

● If an M-DV80 tape is used immediately after cleaning, the message, “HEAD CLEANING

REQUIRED!” may not disappear. It does only after the tape has run for some time.

● Use the cleaning tape at room temperature (10˚C to 35˚C).

● Instructions for using the cleaning tape stated on a sheet inside its storage case may be different in part from those stated here.

Follow the instructions in this manual.

Operating environment

Frequency of 1 to 2 times every 1 to 2 times every 1 to 2 times every cleaning 5 hours 20 to 30 hours 5 hours

Low temperature Room temperature High temperature

5˚C to 10˚C 10˚C to 35˚C 35˚C to 40˚C

Cassette tape

BR-DV6000 can record onto and playback standard DV and mini DV cassette tapes (for SP mode only). Use the following JVC cassettes with the or the

logo.

●

Standard DV cassettes

LA-DV276 LA-DV186 LA-DV124

Mini DV cassettes

M-DV63PRO M-DV60 M-DV30

Memo

● DVCAM cassette can be recorded in the DV format.

● Tapes recorded in the DVCAM format can be played (SP Mode).

● M-DV80 cassettes (Mini DV 80min tape) cannot be used with this unit.

Remarks on the use of tape

● Do not load the videotape in the wrong direction.

● Store the tape only after it has been fully rewound, so as to avoid damaging the tape.

● Store the cassette in places low in humidity, well-ventilated and fungus-proof.

● When a cassette tape is used repeatedly, noise may increase due to e.g., dropout, etc. hence

affecting its performance. Do not use dirty or damaged tapes as they will shorten the life span of the rotation head.

䡵 Erasure prevention

DV cassettes have a safety slide at the back to prevent accidental erasure.

•

To prevent accidental erasure of important records, push the slide to the “SAVE” position.

•

To record, push the slide to the “REC” position.

Slide

REC

SAVE

E-8

䡵 For recording and storing videotapes in the best condition

Observe the following instructions for the best recording and storage of videotapes.

•Take care of the conditions of handling videotapes. It is recommended that you record and store videotapes in the environment below.

Storage

Recording Short period Long period

(Up to 10 years) (Over 10 years) Temperature 17°C to 25°C 15°C to 23°C 15°C to 19°C Humidity 30% to 70% 40% to 55% 25% to 35% Hourly temperature change Less than 10°C – – Hourly humidity change Less than 10% – –

• Do not leave the videotapes neglected for a long period. If videotapes are left wound for a long period of time, it may result in distortion of the tape. Also it may cause tape-to-tape adhesion (known as blocking). It is recommended that videotapes be unspooled and rewound once a year for refreshing.

• When tapes are not in use, store them in cases and on end. Storage cases protect videotapes from humidity, dust and ultraviolet. Keep tapes in cases and do not store them lying flat. When housed in a horizontal position, pressure from other tapes can cause distortions and deformations of the tape edges.

Condensation

• When this unit is moved from a cold to a warm

place abruptly, the vapor in the warm air will come into contact with the head drum or the tape guides, which are not warmed enough. When chilled, the vapor turns into droplets of water. This state is known as condensation. When condensation occurs, the videotape adheres to the head drum or the tape guides and will be damaged.

• Condensation occurs on this unit in the fol-

lowing circumstances: * It is moved abruptly from a cold place to a

warm place.

* It is used in a place immediately after the

heater has been turned on, or when cold breeze from an air-conditioner blows onto it.

* It is used at a place of high humidity.

Head drum

Videotape

When a cassette tape is loaded, do not transport e.g., from a cold outdoor place to a warm room thus subjecting the unit to drastic temperature changes. After moving the unit, do not use it until the inner mechanism stabilizes.

• When condensation occurs, the monitor displays the following warning:

CONDENSATION ON DRUM

Leave the unit with the power ON and wait until the WARNING message disappears.

• Prevention of condensation When transporting BR-DV6000 from a cold to a warmer place abruptly, first remove the cassette tape. Then place BR-DV6000 in a plastic bag and seal it before transporting.

Ta ke out BR-DV6000 from the sealed plastic bag only after it has the same temperature as the surroundings.

E-9

NAMES AND FUNCTIONS OF PARTS

– Front panel –

MENU RESET

Mini

MIC

DISP

SEARCH–

SET SEARCH+

BLANK CUE UP

HOLD

PHONES REC LEVEL

CH-1/3 CH-2/4

1 Cassette loading slot/LED

•For loading a cassette into or unloading it from the slot. Insert a standard DV cassette or a mini DV cassette. (☞ Page 38)

• When BR-DV6000 is in the OPERATE OFF state and a cassette is loaded, it changes to the OPERATE ON state.

• With a cassette loaded, the LED lights up in green. When a cassette is being loaded or ejected, the LED flashes.

2 [OPERATE] button/LED

• Press this button to turn on the power and BR-DV6000 becomes ready for operation. (Operate ON)

Press this button again when BR-DV6000 is already on to turn off the power. (Operate OFF)

• OPERATE LED lights up as follows. Operate ON : the green LED lights up

Operate OFF : the red LED lights up VCR error : the red LED blinks

Memo

● If DC IN MODE in the SYSTEM MENU screen is set to “OPE ON” or the Timer Switch is set to “REC” or “PLAY” and power is supplied to the DC IN terminal located on the rear panel, BR-DV6000 goes into the OPERATE ON state even if this button is not pressed.

● Even after the power is turned off with this button, BR-DV6000 is live with a small amount of electricity.

Therefore, if BR-DV6000 is not to be used for a long period of time, please remove the AC adapter to save energy.

PROFESSIONAL

BR-DV6000

A.DUB

REC

EJECT

REW STOP FF

AUDIO INPUT

COUNTER

MONITOR OUTPUT REMOTE

CTL L

CH-1/2

MIX

CH-3/4

OPERATE

PLAY PAUSE

SELECT

LINE

Y/C

(CPN)

LOCAL

3 Operation buttons

䡵 [A. DUB] Audio dubbing button/LED

• Press this button for audio dubbing (after-recording). For audio dubbing, set AUDIO MODE in the AUDIO MENU screen to “32K”. The sound produced by the MIC terminal # or the AUDIO IN terminal is recorded on channels CH3 and CH4.

• During audio dubbing, the red A. DUB LED lights up.

• If the INPUT SELECT switch is set to DV, audio dubbing cannot be performed. (☞ Page 44 “Audio Dubbing”)

䡵 [REC] button/LED

• Hold down this button and press the PLAY button to start recording. During recording, the red LED lights up.

• Hold down this button and press the PAUSE button to pause recording.

• If this button is pressed during recording, an index signal is recorded on the tape (when INDEX WRITE in the SYSTEM MENU screen is set to ON).

• When this button is pressed in the STOP mode, the time code generator value can be checked while the button is being held down. If TC DUPLICATE Menu is set to AUTO, the time code, date and time of the DV input can be checked.

• If this button is pressed during playback, the input signal can be checked while the button is held down. (EE check)

EE check is not available for DV signal input.

E-10

䡵 [PLAY] button/LED

• Press this button to start playing back a tape. During playback, the green LED lights up.

• When recording is paused, press this button to resume recording.

• When audio dubbing is paused, press this button to resume audio dubbing.

䡵 [PAUSE] button/LED

• During recording, press this button to pause it.

• In the PLAYBACK or STOP mode, press this button to enter the STILL mode. In the RECORDING PAUSE or STILL mode, the green LED lights up.

• When BR-DV6000 is in the STILL mode, hold down the A.DUB button and press this button to enter into the audio-dubbing pause mode.

•When BR-DV6000 is in the STILL mode, press this button for frame advance playback.

Memo

Still images or images in frame advance can be selected with STIL/F.ADV of the SYSTEM (1/2) MENU screen.

䡵 [FF] button/LED

• When BR-DV6000 enters the STOP mode, press this button to fast-forward the tape.

• When BR-DV6000 is in the PLAYBACK or STILL mode, press this button for fast-forward playback. The fast forward playback speed can be changed by pressing the SEARCH +/ : button * or the SEARCH –/; button (when “;,:” KEY FUNC in the SYSTEM (1/2) Menu screen is set to VAR). (☞ Page 50 “Search Mode”)

• Hold down the PLAY button and press this button to perform playback in the forward direction at 1.07 times the normal speed. At this state, if the PLAY button is released first, the playback continues at 1.07 times the normal speed.

If this button is released first, it plays back at the normal speed.

• During fast-forwarding or fast-forward playback, the LED lights up in green.

䡵 [STOP] button

• Press this button to stop operation.

• When BR-DV6000 is in the STANDBY OFF mode, press this button to enter the STANDBY ON mode.

Memo

There are two stop modes.

● STANDBY OFF: For protecting the tape and the drum, the drum does not rotate.

● STANDBY ON: The drum rotates so that it starts up faster after BR-DV6000 moves into another mode.

䡵 [REW] button/LED

• When BR-DV6000 enters the STOP mode, press this button to rewind the tape.

• When BR-DV6000 is in the PLAYBACK or STILL mode, press this button for reverse playback. The rewind playback speed can be changed by pressing the SEARCH +/: button * or the SEARCH –/; button (when “;,:” KEY FUNC in the SYSTEM (1/2) Menu screen is set to VAR). (☞ Page 50 “Search Mode”)

• Hold down the PLAY button and press this button to perform playback in the reverse direction at 0.9 times the normal speed. At this state, if the PLAY button is released first, the playback continues at 0.9 times the normal speed.

If this button is released first, it plays back at the normal speed.

• During rewinding or rewind playback, the LED lights up in green.

䡵 [EJECT] button

• Press this button to eject the cassette.

Memo

● It takes about 6 seconds for the cassette to be ejected.

● The cassette can be ejected even when BRDV6000 is in the OPERATE OFF mode. After the eject action is completed, BR-DV6000 returns to the OPERATE OFF mode.

E-11

NAMES AND FUNCTIONS OF PARTS

MENU RESET

Mini

MIC

4 [REMOTE/LOCAL] switch

This switch is used to select how BR-DV6000 is to be operated. LOCAL : Use this setting if BR-DV6000 is to

be controlled with the key operation of the unit.

REMOTE : Use this setting if BR-DV6000 is to

be controlled using the edit controller connected to the REMOTE 1 (9PIN) terminal or REMOTE 2 (12PIN) terminal. When it is set to REMOTE, settings can be performed at the REMOTE (1/2) MENU screen to enable/disable operation via the 9-PIN or 12PIN REMOTE terminal. The 9-PIN REMOTE 1 terminal can be selected using REMOTE SEL 9 PIN while the 12-PIN REMOTE 2 terminal can be selected with REMOTE SEL JVC.

Memo

● To control BR-DV6000 with the SERIAL REMOTE terminal or DV terminal, this switch setting can be set up with REMOTE SEL SERIAL or REMOTE SEL DV in the REMOTE (1/2) MENU screen. (☞ Page 75)

● If it is set to REMOTE, the buttons that can be operated from the unit are selectable from LOCAL FUNCTION in the REMOTE (1/2) MENU screen.

E-12

DISP

SEARCH–

SET

SEARCH+

BLANK CUE UP

HOLD

PHONES REC LEVEL

CH-1/3 CH-2/4

PROFESSIONAL

BR-DV6000

– Front panel – (continued)

OPERATE

A.DUB

REC

PLAY PAUSE

EJECT

REW STOP FF

AUDIO INPUT

COUNTER

MONITOR OUTPUT REMOTE

CTL L

MIX

CH-1/2

CH-3/4

SELECT

MIX

LINE

Y/C

LOCAL

(CPN)

9 8 7 6 5 4

5 [INPUT SELECT] switch

This switch is used to select input signals. DV :For DV signals of the DV IN/OUT

terminal (IEEE1394)

LINE :For inputting the composite images

of the LINE IN terminal and analog audio signals.

Y/C (CPN) :For inputting the YC separate video

signal of the Y/C IN terminal and the component video signal of the COMPONENT IN terminal. The selection of the YC separate signal or the component video signal can be done with VIDEO INPUT SEL in the VIDEO MENU screen. For audio, analog sound is input.

Note

Switching is invalid during recording.

6 [AUDIO OUTPUT] switch

Use this switch to select the audio channel from the headphone terminal and the AUDIO OUT terminal located on the rear panel. This switch is valid in the following conditions.

• During playback of tapes recorded in the 32k audio mode

• In the EE mode for DV input in the 32k audio mode

• During audio dubbing

CH-1/2 :For outputting the sound of the

MIX :For outputting the mixed sound of

CH-3/4 :For outputting the sound of CH3 and

channels CH1 and CH2.

CH1 and CH3 from the CH-1/3 AUDIO OUT terminal and the mixed sound of CH2 and CH4 from the CH2/4 AUDIO OUT terminal.

CH4.

Memo

● For the MIX setting, noise is sometimes generated. If it occurs, set it to CH-1/2 or CH-3/4.

● In the 48 K audio mode, it is fixed at channels CH1 and CH2 regardless of the setting of the switch.

7 [AUDIO MONITOR] switch

Use this switch to select the audio channel for output signals from the headphone terminal and the AUDIO MONITOR terminal located on the rear panel. The output signal of the AUDIO MONITOR OUT terminal is monaural.

L :For outputting the sound of CH1. MIX :For outputting the mixed sound of CH1

and CH2.

R :For outputting the sound of CH2.

Memo

In the following conditions, if this switch and the

6 AUDIO OUTPUT switch are used in combi-

nation, the AUDIO MONITOR OUT outputs the sounds listed as in the following table.

• During playback of tapes recorded in the 32 K audio mode

• In the EE mode for DV input in the 32 K audio mode

• During audio dubbing

AUDIO switch

MONITOR

MIX

OUTPUT

CH-1/2

MIX

CH-3/4

CH-1/2

MIX

CH-3/4

CH-1/2

MIX

CH-3/4

MONITOR OUT output channel

CH1

CH1/3 mix

CH3

CH1/2 mix

CH1/2/3/4 mix

CH3/4 mix

CH2

CH2/4 mix

CH4

8 [COUNTER] switch

The switch changes the contents of the counter display of the 9 LCD and the monitor. CTL : It displays the counter in hour, minute,

second and frame based on CTL (control signal).

TC : It displays the time code data. UB : It displays the user’s bit (UB).

9 LCD

䡵 In the playback, still or search mode, it

displays the playback image.

In the recording, recording pause, stop, fast-forwarding or rewinding mode, it displays the input image.

䡵 The following information is also dis-

played.

•Various types of information (status display), e.g., operation mode, date/time, counter

• Menu screen

•Warning display

(For details, ☞ Page 20)

Memo

● Use the * DISP button to enable/disable the

LCD display and the display style.

● LCD-related settings, e.g., brightness adjustment of the LCD, are performed in the DISPLAY MENU screen.

(☞ Page 39 “Setting the LCD display”) (☞ Page 82 “DISPLAY MENU screen”)

● If the same image pattern is kept displayed on the LCD display for a prolonged period of time, “ghosting”, the permanent etching of a pattern on a display screen, may occur. To prevent this, turn off the LCD display when it is not in use.

E-13

NAMES AND FUNCTIONS OF PARTS

MENU RESET

Mini

MIC

DISP

SEARCH–

SET

SEARCH+

BLANK CUE UP

HOLD

PHONES REC LEVEL

CH-1/3 CH-2/4

PROFESSIONAL

BR-DV6000

– Front panel – (continued)

OPERATE

REC

A.DUB

EJECT

COUNTER

CTL L

TC UB

MIX

PLAY PAUSE

REW STOP FF

AUDIO INPUT

CH-1/2

CH-3/4

SELECT

MIX

LINE

Y/C

LOCAL

(CPN)

MONITOR OUTPUT REMOTE

0 [REC LEVEL] Volume for audio

recording level for CH1/3 and CH2/4

Use the switch to adjust the audio recording level for CH1 and CH2. During audio dubbing, the audio recording level for CH3 and CH4 can be adjusted with this switch.

Memo

● During DV input, the volume control is not effective.

● During MIC input, only the volume for CH1/3 REC LEVEL is valid.

! [PHONES] terminal

This is the mini jack terminal for connecting to the headphone. (Stereo ø3.5)

• When BR-DV6000 plays back tapes recorded in the 32 kHz mode, the audio channel for outputting from this terminal is selected with the 6 AUDIO OUTPUT switch.

@ [PHONES] Headphone volume

Use this switch to adjust the output level of the PHONES terminal. Both channels are adjusted at the same time.

# [MIC] terminal

This is the mini jack terminal for monaural microphone input. To input sound from a microphone, set the INPUT SELECT switch to LINE or Y/C (CPN). If a microphone is connected, sound for the AUDIO IN terminal located on the rear panel cannot be input. The sound of the microphone is recorded to CH1/CH2 in the recording mode and CH3/CH4 in the audio-dubbing mode.

E-14

$ [HOLD] button

If this button is pressed in the LCD enlarged display mode, the time code preset screen will be displayed on the LCD. When the time code preset screen is displayed, press this button to return to the normal display. (☞ Page 59 “Presetting time code”)

% [MENU] button

If this button is pressed when BR-DV6000 is in the STOP/STILL mode or when no cassette is loaded, the menu is displayed on the LCD or the monitor connected to the VIDEO MONITOR OUT terminal. When the menu is displayed, press this button to return to the normal display. (☞ Page 70 “Setting the menu”)

^ [RESET] button

•To reset the CTL counter display to “00”, press this button.

• If this button is pressed when the time code preset screen is displayed, all the digits of the time code or the user’s bit are reset to “00”.

• When the Multi Cue-up screen is displayed, press this button to clear the registered cueup points.

& [CUE UP] button

When the 8 COUNTER switch is set to TC, press this button to display the Multi Cue-up screen on the monitor or LCD. When the Multi-Cue-up screen is displayed, press this button to start searching the selected tape position. (☞ Page 54 “Multi Cue-up”)

* Special functions/Setting buttons

The following buttons have different functions depending on whether the normal screen or the setting screen is displayed.

Setting screens:

Menu, Date/Time setting, Time code preset and Multi Cue-up

䡵 [DISP/8] button

• During normal display, this button is used to enable/disable the LCD or select display style.

When this button is pressed, the LCD display changes in the following manner.

Enlarged character display ¥ Image/ enlarged character display ¥ Image/charac- ter display ¥ Image display ¥ No display ¥ Enlarged character display...

• When the setting screen is displayed, this button is used to select the items or setting values.

䡵 [BLANK/9] button

• When BR-DV6000 is in the stop mode, press this button to start blank search. It searches the unrecorded part of the tape and goes into the still mode. (☞ Page 52 “Blank search”)

• When the setting screen is displayed, this button is used to select the items or setting values.

䡵 [SEARCH+/:] button

• During normal display, the function of this button can be selected using “;,:” KEY FUNC in the SYSTEM (1/2) Menu screen.

If it is set to VAR, the searching speed increases if this button is pressed during a search operation. (☞ Page 50 “Search mode”)

If it is set to INDEX, press this button to start forward index search. This function is not effective during recording or recording pause. (☞ Page 52 “Index search”)

• When the setting screen is displayed, this button is used to select items or setting digits.

䡵 [SEARCH–/;] button

• During normal display, the function of this button can be selected using “;,:” KEY FUNC in the SYSTEM (1/2) Menu screen. If it is set to VAR, the searching speed decreases if this button is pressed during a search operation. (☞ Page 50 “Search mode”)

If it is set to INDEX, press this button to start reverse index search. This function is not effective during recording or recording pause. (☞ Page 52 “Index search”)

• When the setting screen is displayed, this button is used to return to the previous menu or select setting digits.

䡵 [SET] button

• When the Menu screen, Date/Time setting screen or the Multi Cue-up screen is displayed, press this button to confirm the setting value.

• When the time code preset screen is displayed, press this button to preset the selected time codes or user’s bit to the time code generator.

E-15

NAMES AND FUNCTIONS OF PARTS

1 6 7 ! @

– Rear panel –

2 3

VIDEO

LINE

Y/C

OUT

COMPONENT

B-YR-Y

SIGNAL

GND

MONITOR

OUT

DC12V

SYNC IN

IN/OUT

IN OUT

TIME CODE

IN OUT

SERIAL

REMOTE

5809#%

1 [VIDEO LINE IN] terminal (BNC)

This is the input terminal for composite video signals.

•To input video via this terminal, set the INPUT SELECT switch located on the front panel to “LINE”.

2 [VIDEO Y/C IN] terminal (4-PIN)

This is the input terminal for YC separate video signals.

•To input video via this terminal, the following settings are required. Set VIDEO INPUT SEL in the VIDEO Menu screen to “Y/C”. Set the INPUT SELECT switch located on the front panel to “Y/C (CPN)”.

• When wide-screen ID signals are input, the wide-screen ID signal is recorded.

3 [VIDEO LINE OUT] terminal (BNC)

This is the output terminal for composite video signals.

4 [VIDEO Y/C OUT] terminal (4-PIN)

This is the output terminal for Y/C separate video signals.

• When tapes that have recorded wide-screen signals are played back, the wide-screen ID signal is output.

REMOTE2

AUDIO

OUT

CH 1/3 CH 2/4

OUT

OFF

REC PLAY

TIMER

MONITOR

OUT

REMOTE1

5 [VIDEO MONITOR OUT] terminal

(BNC)

This terminal is for connecting to a monitor-TV.

• It outputs composite video signals.

• It displays the Menu setting screen, Date/ Time setting screen and warning information.

• If DISPLAY in the DISPLAY Menu screen is set to “ON” or “AUTO”, information will be displayed on-screen, e.g., the operation mode,

date/time and counter. (☞ Page 20)

6 [COMPONENT IN] terminal

(BNC⳯3)

This is the input terminal for component video signals (Y/R-Y/B-Y).

•To input video of this terminal, the following settings are required. Set VIDEO INPUT SEL in the VIDEO Menu screen to COMPONENT. Set the INPUT SELECT switch located on the front panel to “Y/C (CPN)”.

7 [COMPONENT OUT] terminal

(BNC⳯3)

This is the output terminal for component video signals (Y/R-Y/B-Y).

Memo

Whether or not to enable SET UP for analog signals (composite, YC separate and component signals) can be selected with SET UP in the VIDEO Menu screen (for NTSC only).

E-16

8 [SYNC IN] synchronization input

terminal (BNC)

This is the terminal for inputting reference synchronization signals from an external source. For external synchronization signals, input composite video signals of 1V (p-p) or lower (e.g., black burst signal). (☞ Page 29 “Synchronization signal”)

9 [TIME CODE IN] terminal (BNC)

This is the EBU-compliant time code input terminal. It is for connecting to an external time code generator. For external time code signals, use those that synchronize with the video signals.

•To input external time codes, set TCG SOURCE of the TC/UB/CLOCK Menu to “EXTERNAL”.

0 [TIME CODE OUT] terminal (BNC)

This is the EBU-compliant time code output terminal. It outputs time codes recorded on the tape during playback and data generated by the time code generator during recording. With the COUNTER switch set to CTL, time code is not output.

! [CH1/3 AUDIO IN] terminal (RCA)

Use this terminal to input analog audio signals. To enable audio input via this terminal, set the INPUT SELECT switch located on the front panel to “LINE” or “Y/C (CPN)”. Usually, analog signals are recorded on CH1. For audio dubbing, they are recorded on CH3.

@ [CH2/4 AUDIO IN] terminal (RCA)

Memo

If the AUDIO IN terminal and the MIC terminal located on the front panel are used simultaneously, the MIC terminal will precede.

# [CH1/3 AUDIO OUT] terminal

(RCA)

Use this terminal to output analog audio signals. In the 48k audio mode, it outputs the sound of CH1. When audio dubbing is paused, it outputs the sound of CH3. In the 32k audio mode, the sound is selected with the AUDIO OUTPUT switch located on the front panel. (Refer to the table below.)

$ [CH2/4 AUDIO OUT] terminal

(RCA)

Use this terminal to output analog audio signals. In the 48k audio mode, it outputs the sound of CH2. When audio dubbing is paused, it outputs the sound of CH4. In the 32k audio mode, the sound is selected with the AUDIO OUTPUT switch on the front panel. (Refer to the table below.)

Memo

In the following modes, the channel that receives output signals from the AUDIO OUT terminal can be selected with the AUDIO OUTPUT switch.

• During playback of tapes recorded in the 32k audio mode

• During audio dubbing

• In the EE mode for DV input in the 32k audio mode

AUDIO OUTPUT switch

CH1/2 CH1 CH2

MIX CH1, 3 mix CH2, 4 mix

CH3/4 CH3 CH4

AUDIO OUT terminal

CH1/3 CH2/4

% [AUDIO MONITOR] terminal (RCA)

This terminal is for connecting to a monitor TV and monitors the sound from its speakers. Monaural sounds are output.

• The audio channel to be monitored can be selected with the AUDIO MONITOR switch located on the front panel.

For audio channels that receive output sig-

nals from this terminal in the 32k audio mode, refer to the table in page 13.

E-17

NAMES AND FUNCTIONS OF PARTS

– Rear panel – (continued)

COMPONENT

SYNC IN

B-YR-Y

IN OUT

TIME CODE

IN OUT

SERIAL

IN/OUT

REMOTE

^ ( ⁄ ¤ )‹

Y/C

SIGNAL

GND

MONITOR

LINE

OUT

VIDEO

DC12V

^ DC power input terminal (2-PIN)

This terminal is for inputting DC 12 V. Connect the DC power cord of the supplied AC adapter.

Memo

● When power is supplied to this terminal, the OPERATE indicator located on the front panel lights up. (The indicator turns red when BRDV6000 is in the OPERATE OFF state)

● Whether to set BR-DV6000 to enter the OPERATE ON mode or OPERATE OFF mode when power is supplied to the terminal can be selected with DC IN MODE in the SYSTEM (2/2) Menu screen.

● If the ) TIMER switch on the rear panel is set to “REC” or “PLAY”, recording or playback will be automatically started when power is supplied to the terminal. (Timer recording/ playback)

& [SIGNAL GND] terminal

This is the grounding terminal for signals.

* DC power cord clamp

Use this clamp to fasten the DC power cord.

( [DV IN/OUT] terminal

This is the input/output terminal for IEEE1394compliant digital signals. It is for connecting to video equipment with a DV terminal.

•To enable signal input via this terminal, set the INPUT SELECT switch located on the front panel to “DV”.

• Signals that come from this terminal are output regardless of the setting of the INPUT SELECT switch.

• If REPLICATION of the SYSTEM (2/2) Menu is set to DV, the REC command is output from this terminal when BR-DV6000 begins playback. (REPLICATION mode)

• Set PB/DV IN in the SYSTEM(2/2) Menu screen according to the signal format to be input to this terminal. (NTSC or PAL)

E-18

OUT

CH 1/3 CH 2/4

OFF

REC PLAY

TIMER

REMOTE2

AUDIO

OUT

MONITOR

OUT

REMOTE1

) [TIMER] recording/playback

switch

This switch is for setting BR-DV6000 to start timer recording or timer playback when power is supplied to the ^ DC power input terminal according to an external timer.

OFF : No timer recording or timer playback. REC : When power is supplied, BR-DV6000

starts recording automatically. (Timer recording)

PLAY : When power is supplied, BR-DV6000

starts playback automatically. (Timer playback)

Memo

● If the TIMER switch is set to “REC” or “PLAY”, BR-DV6000 automatically enters the OPERATE ON mode upon DC power on even when DC IN MODE in the SYSTEM (2/2) Menu screen is set to “OPE OFF”.

⁄ [SERIAL REMOTE IN] terminal

(mini jack)

This terminal is for connecting to the serial remote controller RM-G30 (sold separately). To operate BR-DV6000 with this terminal, perform the following settings.

• Set REMOTE SEL SER in the REMOTE (1/2) Menu screen to “ON” or “LOC+REM”.

ON : When the 4 REMOTE / LOCAL

LOC+REM: This terminal is effective regardless

Memo

● To use this terminal as the foot switch input, set FOOT SW in the REMOTE (2/2) Menu screen. (☞ Page 77)

switch on the front panel is set to “REMOTE”, this terminal becomes effective.

of the setting of the 4 REMOTE / LOCAL switch on the front panel.

›

ﬁ

¤ [SERIAL REMOTE OUT] terminal

(mini jack)

• This terminal is for direct through-output of serial commands of the serial remote input terminal. (Only with OPERATE ON)

• If REPLICATION of the SYSTEM (2/2) Menu screen is set to SERIAL, this terminal outputs REC commands when BR-DV6000 begins playback. (REPLICATION mode)Use this function to connect BR-DV6000 to a dubbing device for dubbing its playback video or playback sound.

‹

[REMOTE1] RS-422A terminal (D-SUB 9-PIN)

This terminal is for connecting to an RS-422A serial interface-compatible editing remote controller (e.g. RM-G820). With this terminal, BR-DV6000 can be used as a player or recorder of an editing system. To operate BR-DV6000 with RS-422A, perform the following settings.

• Set REMOTE SEL 9-PIN in the REMOTE (1/2) Menu screen to “ON”.

• Set the 4 REMOTE / LOCAL switch on the front panel to “REMOTE”.

Memo

● Use screws, of the metric, not inch, system, for fastening the connectors.

● This part can be replaced by the RS-232C serial interface board SA-K46U (sold separately). Consult your JVC authorized service agent for such replacements.

› [REMOTE2] JVC Bus terminal

(12-PIN)

This terminal is for connecting to the JVC bus interface-compatible editing remote controller (RM-G800). With this terminal, BR-DV6000 can be used as a player or recorder of an editing system. To operate BR-DV6000 with this terminal, perform the following settings.

• Set REMOTE SEL JVC in the REMOTE (1/2) Menu screen to “ON”.

• Set the 4 REMOTE / LOCAL switch on the front panel to “REMOTE”.

ﬁ Slot cover for an optional board

This cover can be removed to install any of the following optional boards.

• SA-DV6000 network board

• SA-X61U AUDIO XLR IN board (2ch)

• SA-X62U AUDIO XLR OUT board (2ch)

Memo

● With the SA-X61U AUDIO XLR IN board installed, whether sound signals are input to the XLR IN terminal or the AUDIO IN terminal can be selected with AUDIO INPUT SEL in the AUDIO MENU. If the MIC terminal is in use, the MIC terminal precedes.

● With the SA-X62U AUDIO XLR OUT board installed, the audio channel to which signals are output can be selected with the AUDIO OUTPUT switch.

E-19

ON-SCREEN DISPLAY – On-screen display –

Besides E-E images and playback images, the monitor connected to the VIDEO MONITOR OUT terminal provides the following on-screen information. Press the DISPLAY button to display the same information on the LCD screen of BR-DV6000.

DISP button

Monitor

Mini

MIC

MENU RESET

DISP

SEARCH–

SET SEARCH+

BLANK CUE UP

HOLD

PHONES REC LEVEL

CH-1/3 CH-2/4

PROFESSIONAL

BR-DV6000

REC

A.DUB

REW STOP FF

EJECT

COUNTER

MONITOR OUTPUT REMOTE

CTL L

MIX

OPERATE

PLAY PAUSE

AUDIO INPUT

CH-1/2

MIX

LINE

CH-3/4

(CPN)

Y/C

SELECT

VIDEO MONITOR OUTPUT

LOCAL

LCD screen

On-screen display Description Operation

Status display

Event display

Alarm display

Warning display

Menu display

Multi Cue-up screen

Displays the setting status of the VCR operation mode, date/time, counter.

Displays the operating status of blank search, index recording/search.

Displays error/alarm messages for incorrect operation or improper condition of BR-DV6000.

When an error occurred with the VCR, it displays warnings with the relevant error codes. (☞ Page 98)

Displays the menu setting screen. (☞ Page 69)

Displays the Multi Cue-up screen for registering or selecting cue-up (searching) point. (☞ Page 54)

Settings can be performed with DISPLAY in the DISPLAY (1/2) Menu screen.

ON : Always display. According

AUTO : It displays for about 4 sec-

OFF : No on-screen display. The

Display on the LCD

The on-screen display changes whenever the DISPLAY button is pressed. (☞ Page 26)

It is displayed automatically when an error with the VCR occurred.

When BR-DV6000 enters the STOP/ STILL mode or no cassette tape is loaded, the menu is displayed when the MENU button is pressed.

When BR-DV6000 enters the STOP, STILL or PLAY mode, press the Cue-up button to display the Multi Cue-up screen.

DISPLAY (1/2) Menu screen

–––DISPLAY[ 1 / 2 ] –––

LCD BRI GHTNESS 0 LCD CHROMA 0 LCD CONTRAST 0 LCD AUTO OFF OFF DISPLAY ON COUNT ER POS I . LOWE R - R NEXT PAGE PAGE BACK

to each event or error, the event and alarm displays are shown for about 3 seconds.

onds during mode changes.

alarm display is shown according to errors, which occurred.

E-20

ON-SCREEN DISPLAY – Status display –

03 / 04 / 03 STANDBY-OFF 11 : 20 : 00 TCR 02:00:00:00

03 / 04 / 03 11 : 20:00

䡵 Status display: It displays the current settings and operating status.

32K CH–1/2 0SP mi n00 ASSEM

ARNING 7001

DRUM MOTOR FA I LURE

REC I NH I B I T

03 / 04 / 03 STANDBY 11 : 20 : 00 TCR 02:00:00:00

OFF

Memo

● With the DATE REC function in use, the last line is fixed to the date/time display. The information displayed on the last line moves to the line above. (DATE REC function: ☞ Page

81)

No. Item Description

Sampling frequency/audio

output CH

Memo

If the counter display position is set to the upper left, this item will be displayed on the lower right.

• Sampling frequency During recording, the setting value of AUDIO MODE in the

AUDIO Menu screen is displayed (32k or 48k). During playback, the sampling frequency of the sound re-

corded on the tape is displayed (32k, 48k, 44.1k). During DV signal input, the sampling frequency of the sound

input is displayed.

• A.LOCK Lights up when the video and audio sampling clocks (at

48kHz) are synchronized in the PLAYBACK mode. Always lights up in the RECORDING mode and EE mode.

•Audio output channel During playback, the audio channel output from the AUDIO

OUT terminal is displayed (CH1/2, CH3/4, MIX). (only in 32k mode)

• With AUDIO INFO. in the DISPLAY Menu screen, whether to display this item can be selected.

Date/time

Memo

If the display position of the counter is set to the lower left, this item will be displayed on the lower right.

• It displays the date (DD/MM/YY) and time (HR:MM:SS).

• When the unit is in the RECORDING or STOP mode, it displays the data of the built-in clock.

• During playback, fast-forwarding or rewinding, the data recorded on the tape is displayed.

• During DV signal recording, the data from the DV terminal is displayed. If the REC button is pressed in the STOP mode, the input data from the DV terminal will be displayed.

• The style for displaying the date and time can be selected with DATE STYLE and TIME STYLE in the DISPLAY Menu screen.

• Whether to display date/time and the type of display can be selected with TIME/DATE in the DISPLAY Menu screen.

• When the data/time is not set or when a tape is played with no date/time data recorded, “– –” will be displayed.

E-21

ON-SCREEN DISPLAY – Status display – (continued)

32K CH–1/2 0SP mi n00 ASSEM

ARNING 7001

DRUM MOTOR FA I LURE

REC I NH I B I T

03 / 04 / 03 STANDBY 11 : 20 : 00 TCR 02:00:00:00

OFF

No. Item Description

Counter display Displays the CTR counter, time code or user’s bit. The dis-

played contents can be selected using the COUNTER switch.

• CTL counter: It will be displayed if the COUNTER switch is set to CTL. The counter shows a 7-digit number (hour, minute, second and frame) with + or – and “CTL” at the beginning, e.g., CTL9:30:20:10

• Time code : It will be displayed if the COUNTER switch is set to TC. The time code shows an 8-digit number (hour, minute, second and frame)

At playback, the time codes recorded on the tape are displayed.

The prefix indicates the time code mode.

TCG : Time code generator data TCR : Time code reader data DTCG : Time code data received from the DV IN / OUT

terminal

ETCG : External time code generator data

Depending on the framing mode, the symbols for the seconds and frames are different (only for NTSC).

00 : 00 : 00 : 00

Dot (.) for the drop frame mode

¥ Colon (:) for the non-drop frame mode

• User’s bit : it will be displayed if the COUNTER switch is set to UB.

The user’s bit is an 8-digit number (each digit is a number or character from 0 – F).

The prefix indicates the user’s bit mode.

UBG : User’s bit generator data UBR : User’s bit reader data DUBG : User’s bit reader data received from the DV IN /

OUT terminal

EUBG : External user’s bit generator data

Memo

● The position of the counter display can be changed with COUNTER POSI in the DISPLAY Menu screen.

● The counter display can be turned on/off with TIME CODE in the DISPLAY Menu screen.

E-22

ON-SCREEN DISPLAY – Status/Event display –

No. Item Description

VCR operation mode

Remaining tape

Memo

If the counter display position is set to the upper right, this item will be displayed on the lower right.

Edit mode display

Memo

● With the counter display shown on the top left, this display appears on the bottom right.

● In the 48 k audio mode, insert editing is not possible in the following cases.

INS A1, INS A2, INS VA1, INS VA2

䡵 Event display : When certain functions are in use, it is displayed at the following posi-

tions (with the DISPLAY mode ON or AUTO).

32K CH–1/2 0SP mi n00

03 / 04 / 03 STANDBY 11 : 20 : 00 TCR 02:00:00:00

BLANK SEARCH

INDEX DETECTED

Displays the VCR operation mode, including: PLAY, EJECT, FF, REW, STANDBY-ON, STANDBY-OFF, STILL, REC, REC PAUSE, A. DUB, A. DUB PAUSE, ASSEM EDIT, INSERT EDIT, SHTL (shuttle search), JOG, BLANK SRH (blank search), NO CASSETTE (cassette tape not loaded), OPERATE OFF. For SHTL and JOG, the speed is also displayed.

• The display can be turned on/off with VTR MODE in the DISPLAY Menu screen.

Displays the remaining time of tape (minutes). Not displayed when the remaining time is being confirmed.

• The display can be turned on/off with TAPE REMAIN in the DISPLAY Menu screen.

• The SP display disappears when a DVCAM cassette tape is being played back.

• This remaining tape time display is only for reference.

Displays the edit mode selected, e.g., by using the edit mode controller.

• ASSEM : Assemble editing

• INS V : Video insert editing

• INS A :Audio insert editing (Audio: both CH 1 and CH 2)

• INS VA :Video, audio insert editing (Audio: both CH 1 and

• INS VA :Video/Audio insert editing

• INS TC :Time code insert editing (Time code only)

CH 2)

Insert editing in the 32 k audio mode

• INS A12 :CH1, CH2 audio

• INS A34 :CH3, CH4 audio

• INS VA12: Video & CH1, CH2 audio

• INS VA34: Video & CH3, CH4 audio

• INS A : CH1 to CH4 audio

• INS VA : Video & CH1 to CH4 audio

The display can be turned on/off with EDIT INFO in the DISPLAY Menu screen.

● “A” display: displayed during operation

Display Description

Blank search in progress.

Index search in progress. The number indicates the index search position.

When an index has been specified on the tape during recording.

OFF

BLANK SEARCH

INDEX +1

INDEX MARK

● “B” display: displayed for about 3 seconds

Display Description

INDEX DETECTED

VIDEO END DETECTED

An index has been detected during index repeat operation.

The video end has been detected during end repeat operation.

E-23

ON-SCREEN DISPLAY – Alarm display –

䡵 Alarm display: An alarm message is displayed at the following positions when there has

been an operation error or when BR-DV6000 is not in good condition, e.g., dirty head.

32K CH–1/2 0SP mi n00

● “A” display : The state of BR-DV6000 is displayed. It continues to be displayed until the error state is corrected. This display is not affected by the setting of the display mode.

HEAD CLEANING REQUIRED!

NO DV S I GNA L

03 / 04 / 03 STANDBY 11 : 20 : 00 TCR 02:00:00:00

OFF

Display Description

LOW VOLTAGE

HEAD CLEANING REQUIRED!

OVERHEATING!

The voltage of the DC power source is low. If the operation continues, it enters the Operate OFF mode.

The video head is dirty. Clean it with the head-cleaning tape exclusively for BRDV6000. (☞ Page 8) If the head is clogged, it is detected in the PLAYBACK mode and this message is displayed.

The temperature inside BR-DV6000 has exceeded the stated value. Disconnect the power and place it at a cool place. If this message is displayed again, BR-DV6000 could be defective. Consult your JVC-authorized service agent.

● “B” display : Messages for incorrect operation are displayed for about 3 seconds. They are displayed when the DISPLAY mode is ON or AUTO.

Display Description

INVALID TAPE!

LP TAPE!

NO DV SIGNAL

COPY INHIBIT

REC INHIBIT

REC INHIBIT (NTSC/PAL)

E-24

Data tape for PCs or DVC PRO tape is used. The cassette tape will be automatically ejected.

The user attempted to play back a tape recorded in the LP mode. BR-DV6000 cannot record or play in the LP mode.

The user attempted to record without DV signal input.

The user attempted to record copy-guarded signals.

The user attempted to record on a tape that is not ready for recording (the rear switch is set to SAVE).

The user attempted to record analog signals when PB/DV IN in the SYSTEM (2/2) Menu is set to NTSC.

Display Description

A. DUB INHIBIT (REC TAB)

A. DUB INHIBIT (48 K)

A. DUB INHIBIT (LP)

A. DUB INHIBIT (BLANK)

A. DUB INHIBIT (DV)

A. DUB INHIBIT (NTSC/PAL)

A. DUB INHIBIT (DVCAM)

EDIT INHIBIT (REC TAB)

EDIT INHIBIT (LP)

EDIT INHIBIT (BLANK)

EDIT INHIBIT (NTSC/PAL)

EDIT INHIBIT (DVCAM)

EDIT INHIBIT (AUDIO)

EDIT INHIBIT (DV TC INS)

DV EE INHIBIT

The user attempted to perform audio dubbing on a tape that is not ready for recording (the rear switch is set to SAVE).

This message is displayed when audio dubbing is attempted under the following conditions.

• AUDIO MODE of the AUDIO Menu screen is set to 48 K.

• The tape is recorded with a sampling frequency of 48kHz

The user attempted to perform audio dubbing on a tape recorded in the LP mode.

The user attempted to perform audio dubbing of a blank tape.

The user attempted to perform audio dubbing during DV signal input (with the INPUT SELECT switch set to “DV”).

The user attempted audio dubbing when PB/DV IN in the SYSTEM (2/2) Menu screen is set to NTSC.

The user attempted to perform audio dubbing on a DVCAM format tape.

The user attempted to edit a tape that cannot be recorded (with the rear switch set to “SAVE”).

The user attempted to edit a tape recorded in the LP mode.

The user attempted to insert-edit an unrecorded part of a tape.

The user attempted editing when PB/DV IN in the SYSTEM (2/2) Menu screen is set to NTSC.

The user attempted to edit a tape recorded in the DVCAM format.

The user attempted editing in an audio combination that cannot be edited.

The user attempted time-code insert-editing during DV signal input.

This message is displayed when the REC button is pressed during playback with the INPUT SELECT switch set to DV. (EE check is not allowed during DV input.)

OPERATION LOCK

This message is displayed when an operation button is pressed with OPERATION LOCK enabled. To enable OPERATION LOCK, set OPERATION LOCK in the SYSTEM (2/2) Menu screen to ON.

E-25

2 1

4 5

8 9

ON-SCREEN DISPLAY – LCD display –

There are two display modes for the status display on the LCD of the unit.

• Same character display mode as the monitor output

• LCD display mode (enlarged display)

DISPLAY button

OPERATE

REC

PLAY PAUSE

Mini

MIC

MENU RESET

DISP

SEARCH–

SET

BLANK CUE UP

HOLD

PHONES REC LEVEL

CH-1/3 CH-2/4

SEARCH+

PROFESSIONAL

BR-DV6000

A.DUB

REW STOP FF

EJECT

COUNTER

MONITOR OUTPUT REMOTE

CTL L

MIX

AUDIO INPUT

CH-1/2

MIX

LINE

CH-3/4

Y/C

(CPN)

SELECT

LCD

Memo

● With LCD AUTO OFF in the DISPLAY Menu screen, the LCD display can be set to disappear if it continues to be on for a certain time.

When the display goes off automatically, press any button to return to the original display mode.

● The LCD display area is smaller compared with the one for the actual images.

䡵 LCD display mode (enlarged display)

The LCD display mode changes in the following sequence whenever the DISPLAY button is pressed (with DISPLAY of the DISPLAY Menu screen set to ON or AUTO).

Enlarged

LOCAL

character display

display

Image

display

Image/enlarged

character display

Image/

character display

CH1/3

48k

CH2/4

NTSC

FREE

PLAY

12H34M34S10

SP222 01/02/03

01:23:45 INS

0@#$&

1 Audio output channel display

It displays the setting status of the AUDIO OUTPUT switch on the front panel. Top (CH 1 /3 AUDIO OUT): CH 1, CH 3, CH 1 /3 Bottom (CH 2 /4 AUDIO OUT): CH 2, CH 4, CH 2 /4

Audio sampling frequency display

• During recording, it displays the setting status of AU-

DIO MODE of the AUDIO Menu screen.(48k or 32k)

• During playback, the audio mode of the tape is dis-

played (48k, 32k, or 44.1k)

•L: Displayed during AUDIO LOCK.

E-26

OVER

min

Y/CVASYNC

dB010203040

OVER

^ *

3 Audio level meter display

It displays the input sound level during recording or in the STOP mode, and the playback sound level during playback. The reference recording level of BR-DV6000 is –20dB.

•For playing a tape recorded with a home-use DV machine with a reference level of –12 dB, set AUDIO OUT LEVEL to –12 dB.

4 Drop/Non-drop display (for NTSC only) /NTSC mode

Displays the framing mode of the time code. NDF : Non-drop frame (NTSC only) DF : Drop frame (NTSC only) NTSC : Displays when PB/DV IN in the SYSTEM (2/2)

Menu screen is set to NTSC.

5 Time code mode display

Displays the time code mode set in the TC/UB/CLOCK Menu screen. REGN : Regeneration mode RRUN : REC RUN preset mode FREE : FREE RUN preset mode EXT : This is displayed when time codes are input to

the TIME CODE IN terminal (with TCG SOURCE set to EXTERNAL). It blinks when no time code is input or when the phase of an external time code is not locked with the phase of the video signal.

DUPL : This is displayed when TC DUPLICATE is set

to AUTO. (Enter the time code of the DV terminal.)

6 Counter mode

The counter mode selected with the COUNTER switch on the front panel is displayed.

: CTL counter

: User’s bit

: Time code

7 Counter display

• The CTL counter is displayed as a 7-digit number with + or –. The time code/user’s bit is displayed as an 8-digit number.

• With NTSC, the character/symbol at the end varies depending on the time code framing mode. F: Non-drop frame. .(dot): Drop frame. With PAL, this is fixed to F.

8 VCR mode display

Displays the operation mode of the VCR. The reservation of mode is displayed in blinking light. NOCAS (no cassette tape), EJECT, STBON (standbyon), STBOF (standby-off), PLAY, STILL, FF, REW, SHTL, ADUBP (audio dubbing pause), REC, RECP (recording pause), INSERT, ASSEM, OPOFF (operate off)

9 VCR mode graphic display

c : Eject L : Stop : : Play J :Still Z : FF/Forward search + : REW/ Reverse search: a : Record aJ : Recording pause

:Audio dubbing

J :Audio dubbing pause

0 Tape symbol display

: This symbol is displayed when a cassette tape is

loaded. It blinks during loading or ejecting of a cassette tape. If the rear switch of the cassette tape is set to SAVE, it is displayed in yellow.

! Remaining tape time display

Displays the remaining time (minutes). Blinks if the remaining time is less than 4 minutes. Not displayed when the remaining time is being confirmed. SP will not be displayed when a DVCAM cassette tape is being played back.

@ Time/Date display

The data of the built-in clock will be displayed during recording or in the STOP mode. Displays the data of the tape during playback. If the date/time is not set up, “– – –” is displayed.

# Input video signal display

Displays the input video signal selected with the INPUT SELECT switch on the front panel. Blinks if the selected signal is not input (LINE, Y/C, CPNT, or DV).

LINE, Y/C, CPNT, DV

( In the case of a copy-prohibiting signal, it will be displayed in yellow.

SYNC

: It is displayed when signals are input via the SYNC

IN terminal with EXTERNAL SYNC selected.

)

$ Editing mode display

The editing mode selected with the editing remote controller is displayed. (ASSEM, INSV, INSA, INSVA, INS TC, INS VA12, INS VA34, INS A12, INS A34)

% Timer display

r : It is displayed when the TIMER switch on the rear

panel is set to REC or PLAY. REC: RED PLAY: GREEN

^ Wide screen ID signal display

: It will be displayed when a wide screen ID signal

exists in the input signal of the Y/C or DV terminal. The data on the tape is displayed during playback.

& Condensation display

: It is displayed when condensation occurs.

* Option display

It is displayed when an option board is connected.

XLI

: SA-X61U connection

XLO

: SA-X62U connection : SA-DV6000 connection

E-27

CONNECTION – Connecting video signals –

Video output, e.g., VCR Synchronization signal generator

BB signal

SYNC IN

Monitor

Composite

Y/C

VIDEO

LINE

Y/C

OUT

MONITOR

OUT

SIGNAL

GND

Y/C

Composite

Component

Output

Video output, e.g., VCR

Input

Component

COMPONENT

IN OUT

SYNC IN

IN/OUT

DC12V

B-YR-Y

TIME CODE

IN OUT

SERIAL

REMOTE

REMOTE2

AUDIO

OUT

CH 1/3 CH 2/4

OUT

OFF

REC PLAY

MONITOR

TIMER

OUT

REMOTE1

MONITOR OUT (Composite)

 Output signal

When BR-DV6000 enters the STOP, REC or EDIT mode, the input signal (E-E image) is output. In the PLAYBACK mode (including the playback of the pre-roll part during editing), playback images are output. However, in the edit mode with analog input, signals cannot be output to the DV OUT terminal properly.

● Analog signal

• LINE OUT terminal (BNC): composite signal.

• Y/C OUT terminal (4-PIN): YC separate sig-

nal. When a wide screen ID signal exists in the video signal, the ID signal is output.

• COMPONENT OUT terminal (BNC3):

Component (Y/B-Y/R-Y) signals are output.

● Digital signal

•DV IN/OUT terminal: it outputs IEEE1394-

compliant digital video signals. When a wide screen ID signal exists in the video signal, the ID signal is output.

● Connection with a monitor TV

A monitor TV can be connected to the MONITOR OUT terminal. Besides the composite video signals, it also displays the on-screen display for status or menu screen.

Memo

Set PB/DV IN in the SYSTEM (2/2) Menu screen according to the signal format of the tape to be played. (NTSC or PAL)

 Input signal

The input video signal is selected with the INPUT SELECT switch on the front panel. Set VIDEO INPUT SEL in the VIDEO Menu screen to select YC input or component input.

● Analog signal

• LINE IN terminal (BNC): composite signal

• Y/C IN terminal (4-PIN): YC separate signal When a wide screen ID signal is being input, the ID signal is recorded.

• COMPONENT IN terminal (BNC3): The component (Y/B-Y/R-Y) signal.

● Digital signal

•DV IN/OUT terminal : IEEE1394-compliant

digital video signals

are input. When a wide screen ID signal is being input, the ID signal is recorded. Set PB/DV IN in the SYSTEM (2/2) Menu screen according to the signal format to be input to the DV terminal. (NTSC or PAL).

Memo

Whether or not to enable SET UP for analog I/O signals of signals can be selected with SET UP in the VIDEO Menu screen (for NTSC only).

E-28

Caution on video signals

● If search images or video signals with a high

level of jitter are input, images or sound may be distorted temporarily. Thus, input stable signals, e.g., those having gone through a TBC.

● A digital VCR requires that video signals for

recording be delivered from a stable source. Video signals from an analog VCR must be run through a TBS or TBC.

● When a component output is executed for

composite-input video, discoloration may occur on the left side of the screen. It is not a defect.

 Synchronization signal

In order to enhance the level of edit precision, input synchronization signals to all the devices of the editing system during editing. For BR-DV6000, input external synchronization signals into the SYNC IN terminal. For external synchronization signals, use video signals of 1V (p-p) or lower (e.g., black burst signals).

To edit DV signals, synchronization signal input is required.

Types of synchronization signal:

BR-DV6000 is operated based on one of the following 3 types of synchronization signal.

• Synchronization signals produced by the synchronization signal generator inside the VCR (INT)

• Video signals from the video signal input terminal (VIDEO)

• Synchronization signals from the SYNC IN terminal (EXT)

Selection of synchronization signals:

Synchronization signals should be selected depending on whether external synchronization input (SYNC IN) or video input (VIDEO IN) exists or on the SYNC SELECT Menu settings. Synchronization signals are selected as shown in the following table.

SYNC IN

VIDEO IN

Playback

EXTERNAL

AUTO

❈

Record

❈

Playback

Record

The above can be selected with SYNC SELECT in the SYSTEM Menu screen.

No YesYe s N o

No YesNo Yes

INT

EXT

INT

VIDEO

INT

EXT

VIDEO

INT

VIDEO

EXT

VIDEO

EXT

VIDEO

Memo

● During DV signal recording, the status of

synchronization signals will be as shown below regardless of the SYNC SELECT menu settings.

SYNC IN terminal

signal

Input

No input

Synchronization signals

EXT

● Regardless of the setting of SYNC SELECT,

when a tape recorded in NTSC is played back, synchronization signals are as shown below.

SYNC IN terminal NTSC signal input PAL signal input or No signal input

Synchronization signals

EXT

INT

Caution on synchronization signals

● For external synchronization signals, output-

signal phase adjustments cannot be performed. In addition, the sub carrier cannot be locked.

● Plugging and unplugging of external synchro-

nization signals or video input signals during playback causes distortion of images and sound for about 5 seconds.

E-29

CONNECTION – Connecting audio signals –

Audio output of VCR

Input

B-YR-Y

TIME CODE

SERIAL REMOTE

Analog audio

REMOTE2

AUDIO

OUT

CH 1/3 CH 2/4

OFF

REC PLAY

TIMER

(2 channels)

OUT

MONITOR

OUT

REMOTE1

COMPONENT

VIDEO

LINE

Y/C

OUT

MONITOR

SIGNAL

GND

IN OUT

OUT

SYNC IN

IN OUT

IN/OUT

DC12V

MONITOR OUT analog (monaural)

Analog audio (2 channels)

Output

Audio input of VCR

 Output signal

When BR-DV6000 is in the STOP, REC or EDIT mode, signals (EE sound), which have been input, are output. During the PLAYBACK mode (including the playback of the pre-roll part during editing), the playback sound is output. However, in the edit mode with analog input, signals cannot be output to the DV OUT terminal properly.

● Analog signal

CH 1/3, CH 2/4 AUDIO terminal (RCA2). There are analog audio terminals for 2 channels. For the DV format, tracks are available for 4 channels (in the 32kHz audio mode).

• In the 32kHz mode, from which one of the 4 channels sound is output can be selected with the AUDIO OUTPUT switch on the front panel. (Refer to the table on the right.)

● Headphone terminal

Sound can be checked in stereo using a headphone. The volume can be adjusted with the PHONES switch on the front panel.

• The channel to be output from this terminal in the 32kHz audio mode can be selected with the AUDIO OUTPUT switch. (Refer to the table on the right.)

Slot cover for optional board

Microphone

Monaural

Stereo

Headphone

Monitor

AUDIO OUTPUT switches and output channels

In the following cases, the channels that receive output from the AUDIO OUTPUT terminal vary according to the setting of the AUDIO OUTPUT switch. The table below shows the channels.

• During playback of tapes recorded in the 32kHz audio mode.

• During audio dubbing.

• In the EE mode of DV input in the 32kHz audio mode.

AUDIO OUTPUT switch

CH1/2

MIX

CH3/4

• In the 48kHz audio mode or during normal recording, output goes to CH1 and CH2 regardless of the setting of the switch.

AUDIO OUT terminal

CH1/3

CH2/4

(L)

CH1

CH1/3

CH3

CH2

CH2/4

CH4

(R)

E-30

+ 76 hidden pages