Junkers JU-87D Stuka Instruction Manual
AILERON
FLAP
AILERON
30mm
FLAP
20mm
20mm
Side View
Top View
135mm
Centre of Gravity.
Adjustment.
The front view when the drop tank and the bombs install completion.
75
74
14
73
JU-87D Stuka
Specification:
Length :1691 mm(66.6")
Wing Span :2032 mm(80")
Wing Area :60.3 sq. dm
6.50 sq. ft
Wing Loading :104.5 g/sq. dm
34.2 oz/sq. ft
Flying Weight :6.5 kg(14.3 lbs)
Radio :6ch&8 servos
Engine :108 2-cycle
120 4-cycle
SAFETY PRECAUTIONS
INSTRUCTION MANUAL
First-time builders should seek advice from people having building
experience.If misused or abused,it can cause serious bodily injury
and damage to property.
Fly only in open areas and preferably at a dedicated R/C flying site.
We suggest having a qualified instructor carefully inspect your
airplane before its first flight.Please carefully read and follow all
instructions included with this airplane,your radio control system
and any other components purchased separately.
(The people under 18 years old is forbidden from flying this model)
This R/C airplane is not a toy!
Top view
20mm
20mm
RUDDER
Side View
Top view
Position for
right diagram.
ELEVATOR
Side View
15mm
15mm
5mm
2
Plastic dube (5x30mm)
50mm
90mm
5mm
20mm
Adjustment.
Adjustment.
Drill holes to appropriate in the bomb.
Epoxy plastic tube into the holes.
Drill holes to relevant pesition in the centet wing.
Epoxy the bomb to the bottom wing.
68
67
13
71
69
72
70
4-cycle .120
15″X74.5 in Spinner
6
86
6
6 channel radio for aiplane is highly recommended for this model.
9
Optional parts: rubber wheel with metal hub.
1.5mm
66mm
79mm
123mm
123mm
16mm
3mm
3mm
5
TP Screw (2.3x8mm)
Ply (15x15x3mm)
5
Epoxy plies inside the fuselage under the cowing and
mount the cowing with TP screw as illustration.
Epoxy plies inside the fuselage under the cowing and
mount the cowing with TP screw as illustration.
10
TP Screw (2.3x8mm)
Ply (15x15x3mm)
10
1.5mm
1.5mm
Marked
112mm
35mm
6
TP Screw (3x10mm)
Copper part
2
Ply (15x15x3mm)
4
Assemble the cowling.
Fix the canopy with self - tapping screws.
Drill holes to the marked position in the fuselage,
Drill holes relevant position in the stabilizers.
Assemble the stabilizer strut by TP serew.
Trim slots in right position in the bottem wing.
Epoxy the dummy flaps to the wings.
61
62
63
64
65
12
60
TP Screw (2.3x12mm)
Assemble the flap servo to the main wing with screws.
Main wing joiner
2
A A"
A = A"
Securely glue together. If coming off during flights, you 'll
lose control of your airplane which leads to accidents!
Epoxy main wings to the centre wing by main wing
joiners.
Main wing joiner
2
8
4
Wooden Block(20x20x8mm)
Servo tray(68.5x56.5x2mm)
16
TP Screw (2.3x12mm)
1
Rib template (2mm ply)
2
Wood dowel (6x30mm)
Fix the aileron servo to the serve tray with epoxy.
Fix the flap servo to the servo tray with epoxy.
Assemble the aileron servo to the wing with screws
as below.
According to the rib template drill holes in one wing and
epoxy wood dowel in them.
According to the rib template drill holes to another
main wing.
2
Wood dowel (6x30mm)
1
Rib template (2mm ply)
6mm
Rib template (2mm ply)
Rib template (2mm ply)
6mm
1
2
3
4
5
1
Accessory list for the coming installation steps.
Loading...