JRC NJG1522KB2 Datasheet

NJG1522KB2

SPDT SWITCH GaAs MMIC

KB2 Type

Top view

nGENERAL DESCRIPTION nPACKAGE OUTLINE

NJG1522KB2 is a GaAs SPDT switch suited for RF

receiving circuit of cellular phone handsets.

This switch features very low loss, high isolation and

exhibits wide operating frequency range from 50MHz to

3.0GHz at low voltage of 2.5V.
The ultra small & ultra thin FLP6 package is applied.

nFEATURES

lSingle low voltage control +2.5~+6.5V
lLow insertion loss 0.3dB typ. @f=1GHz, Pin=0dBm

0.5dB typ. @f=2GHz, Pin=0dBm

lHigh isolation 27dB typ. @f=1~2GHz, Pin=0dBm
lHandling power 20dBm max. @f=2GHz, V
lLow current consumption 8uA typ. @f=2GHz, Pin=10dBm
lUltra small & ultra thin package FLP6-B2 (Mount Size: 2.1x2.0x0.75mm)

nPIN CONFIGURATION

Orientation Mark

NJG1522KB2

=2.7V

CTL

nTRUTH TABLE

V
V

PC-P1 ON OFF

PC-P2 OFF ON

NOTE: The values in the table are typical value of insertion loss and return loss.

CTL1

CTL2

Pin connection

1

6

1.P1

2.GND

2

5

3.P2

4.V

CTL2

5.PC

3

“H”=V

4

CTL (H),

“L”=V

6.V

CTL (L)

CTL1

H L L H

L H L H

Insertion Loss=17dB

P1 Return Loss=-2dB

Insertion Loss=17dB

P2 Return Loss=-2dB

Insertion Loss=18dB

P1 Return Loss=-2dB

Insertion Loss=18dB

P2 Return Loss=-2dB

- 1 -

NJG1522KB2

n

ABSOLUTE MAXIMUM RATINGS

PARAMETERS SYMBOL CONDITIONS RATINGS UNITS

Input Power P
Control Voltage V
Power Dissipation P

Operating Temp. T
Storage Temp. T

n

ELECTRICAL CHARACTERISTICS

PARAMETERS SYMBOL CONDITIONS MIN TYP MAX UNITS

in

CTL

D
opr
stg

V

CTL (L)

V

CTL (H)

(V

=0V, V

CTL (L)

- V

CTL (L)

=0V, V

(Ta=25°C, ZS=Zl=50Ω)

=2.7V 28 dBm

CTL (H)

7.5 V

450 mW

-30~+85 °C

-55~+125 °C

=2.7V, ZS=Zl=50Ω, C6=10pF, Ta=25°C)

CTL (H)

Control voltage (Low) V
Control voltage (High) V
Control current I

CTL (L)

CTL (H)

CTL

f=2.0GHz, Pin=10dBm - 8 14 uA

-0.2 0 0.2 V

2.5 2.7 6.5 V

Insertion loss 1 LOSS1 f=1.0GHz, Pin=0dBm - 0.3 0.6 dB
Insertion loss 2 LOSS2 f=2.0GHz, Pin=0dBm - 0.5 0.8 dB
Isolation 1

(PC-P1, PC-P2, P1-P2)

Isolation 2

(PC-P1, PC-P2, P1-P2)

Pin at 1dB
compression point

ISL1 f=1.0GHz, Pin=0dBm 25.5 27 - dB

ISL2 f=2.0GHz, Pin=0dBm 25 27 - dB

P

-1dB

f=2.0GHz 20 24 - dBm

VSWR (PC, P1, P2) VSWR f=0.05~2.2GHz, ON State - 1.3 1.6
Switching time T

SW

f=0.05~2.5GHz - 20 - ns

- 2 -

NJG1522KB2

nTERMINAL INFORMATION

CTL (H)

CTL(L)

CTL(H)

CTL(L)

No. SYMBOL DESCRIPTIONS

1 P1

2 GND

3 P2

4 V

CTL2

5 PC

6 V

CTL1

RF port. This port is connected with PC port by controlling 6th pin (V
to 2.5~6.5V and 4th pin(V

) to -0.2~+0.2V. An external capacitor is

required to block the DC bias voltage of internal circuit. (50~100MHz:

0.01uF, 0.1~0.5GHz: 1000pF, 0.5~2.5GHz: 56pF)
Ground terminal. Please connect this terminal with ground plane as close
as possible for excellent RF performance.
RF port. This port is connected with PC port by controlling 4th pin(V
to 2.5 – 6.5V and 6th pin(V

) to -0.2~+0.2V. An external capacitor is

required to block the DC bias voltage of internal circuit. (50~100MHz:

0.01uF, 0.1~0.5GHz: 1000pF, 0.5~2.5GHz: 56pF)
Control port 2. The voltage of this port controls PC to P2 state. The ‘ON’
and ‘OFF’ state is toggled by controlling voltage of this terminal such as
high-state (2.5~6.5V) or low-state (-0.2~+0.2V). The voltage of 6th pin
have to be set to opposite state. The bypass capacitor has to be chosen
to reduce switching time delay from 10pF~1000pF range.
Common RF port. In order to block the DC bias voltage of internal circuit,
an external capacitor is required. (50~100MHz: 0.01uF, 0.1~0.5GHz:
1000pF, 0.5~2.5GHz: 56pF)
Control port 1. The voltage of this port controls PC to P2 state. The ‘ON’
and ‘OFF’ state is toggled by controlling voltage of this terminal such as
high-state (2.5~6.5V) or low-state (-0.2~+0.2V). The voltage of 4th pin
have to be set to opposite state. The bypass capacitor has to be chosen
to reduce switching time delay from 10pF~1000pF range.

)

)

- 3 -

NJG1522KB2

nELECTRICAL CHARACTERISTICS
(0.1~3.0GHz, with Application circuit, Losses of external circuit are excluded)

PC-P2 Insertion Loss vs. Frequency

(V

=0V,V

0

-0.4

-0.8

-1.2

Insertion Loss (dB)

-1.6

-2
0 0.5 1 1.5 2 2.5 3

CTL1

=2.7V,Pin=0dBm)

CTL2

Frequency (GHz)

PC-P1 Isolation vs. Frequency

(V

-10

-20

=0V,V

0

CTL1

=2.7V,Pin=0dBm)

CTL2

PC-P1 Insertion Loss vs. Frequency

(V

=2.7V,V

0

-0.4

-0.8

-1.2

Insertion Loss (dB)

-1.6

-2
0 0.5 1 1.5 2 2.5 3

CTL1

Frequency (GHz)

=0V,Pin=0dBm)

CTL2

PC-P2 Isolation vs. Frequency

(V

-10

-20

=2.7V,V

0

CTL1

=0V,Pin=0dBm)

CTL2

-30

Isolation (dB)

-40

-50
0 0.5 1 1.5 2 2.5 3

Frequency (GHz)

PC-P1 VSWR vs. Frequency

(V

=2.7V,V

3

2.6

2.2

VSWR

1.8

1.4

1

0 0.5 1 1.5 2 2.5 3

CTL1

Frequency (GHz)

=0V,PC port)

CTL2

-30

Isolation (dB)

-40

-50
0 0.5 1 1.5 2 2.5 3

Frequency (GHz)

P1-PC VSWR vs. Frequency

(V

=2.7V,V

3

2.6

2.2

VSWR

1.8

1.4

1

0 0.5 1 1.5 2 2.5 3

CTL1

Frequency (GHz)

=0V,P1 port)

CTL2

- 4 -