TECHNICAL MANUAL
Of
Intel 945GC +Intel 82801G
Based
Mini-ITX M/B For Intel Atom Processor
NO.G03-NC92-F
Rev1.0
Release date: Oct., 2008
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize pollution
and ensure environment protection of mother earth, please recycle.
ii
TABLE OF CONTENT
USER’S NOTICE.................................................................................................................................. iv
MANUAL REVISION INFORMATION............................................................................................ iv
ITEM CHECKLIST.............................................................................................................................. iv
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD..................................................................................... 1
1-2 SPECIFICATION.................................................................................................................. 2
1-3 LAYOUT DIAGRAM ........................................................................................................... 3
CHAPTER 2 JUMPER SETTING, CONNECTORS AND HEADERS
2-1 JUMPER SETTING..............................................................................................................6
2-2 CONNECTORS AND HEADERS ....................................................................................... 7
2-2-1 CONNECTORS....................................................................................................... 7
2-2-2 HEADERS ............................................................................................................... 9
CHAPTER 3 INTRODUSING BIOS
3-1 ENTERING SETUP……………………………………………………………………… …14
3-2 GETTING HELP..…………………………………………………………………………...15
3-3 THE MAIN MENU…………………………………………………………………………..15
3-4 STANDARD CMOS FEATURES…...………………………………………………………17
3-5 ADVANCED BIOS FEATURES.……………………………………………………………19
3-6 ADVANCED CHIPSET FEATURES….……………………………………………………21
3-7 INTERGRATED PERIPHERALS…….................................................................................23
3-7-1 ONBOARD IDE FUNCTION…….................................................................................24
3-7-2 ONBOARD DEVICE FUNCTION....... ... .................................... ... ...............................25
3-7-3 ONBOARD SUPER IO FUNCTION.............................................................................26
3-8 POWER MANAGERMENT SETUP………………………………………………….……27
3-9 PNP/PCI CONFIGURATIONS..……………………………………………………….……30
3-10 PC HEALTH STATUS………………………………………………………………….……30
3-11 MISCELLANEOUS CONTROL……….. …………………………………………….…….32
3-12 PASSWORD SETTING…………..…………………………………………………………..33
3-13 LOAD SATANDARD/OPTIMIZED DEFAULTS...………………………………………..34
iii
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED,
TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT
WRITTEN PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE INTEL 945GM CHIPSET
MOTHER-BOARD SERIES AND WE DO ASSURE THIS MANUAL MEETS USER ’S R EQ UI RE M EN T BU T WI LL
CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS”
WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTIAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMANGES FOR LOSS OF PROFIT, LOSS OF
BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
1.0 First Edition Oct., 2008
Item Checklist
5
Motherboard
5
Cable(s)
5
CD for motherboard utilities
5
Motherboard User’s Manual
5
I/O Back panel Shield
iv
Chapter 1
Introduction of the Motherboard
1-1 Feature of motherboard
*
Intel 945GC Northbridge and Intel 82801G (ICH7) Southbridge chipset.
*
Onboard Intel Atom CPU, with low power consumption never denies high performance.
*
Support FSB 533 MHz.
*
Support DDRII 400/533 MHz up to 2GB.
*
Onboard Realtek RTL 8111C Gigabit Ethernet LAN.
*
Integrated Realtek ALC662 6-channel HD audio CODEC.
*
Support USB2.0 data transport demands.
1
1-2 Specification
Spec Description
Design
Chipset
Embedded CPU
Memory Socket
∗ Mini ITX form factor 6 layers PCB size: 17.0x17.0cm
∗ Intel 945GC Northbridge chipset
∗ Intel 82801G(ICH7) Southbridge chipset
∗ Intel Atom CPU
∗ Support FSB 533
∗ Low Power Consumption
∗ 240-pin DDRII DIMM socket x1
∗ Support DDRII 400/533MHz system Modules DDRII memory
∗ Expandable to 2GB.
Expansion Slot
Integrate IDE
LAN
Audio
BIOS
∗ 32-bit PCI slot x 1pcs
∗ One PCI IDE controller that supports PCI Bus Mastering, ATA
PIO/DMA and the ULTRA DMA 100/66 functions that deliver
the data transfer rate up to 100 MB/s;
∗ Integrated Realtek RTL8111C PCI-E Gigabit LAN chip.
∗ Support Fast Ethernet LAN function of providing
10Mb/100Mb/1000Mb Ethernet data transfer rate
∗ Realtek ALC662 6 channel Audio Codec integrated
∗ Audio driver and utility included
∗ Award 8MB Flash ROM
2
1-3 Layout Diagram
PS/2 Mouse
PS/2 Keyboard
COM
Connector
VGA
Connector
RJ45 LAN
USB
Connectors
USB
Connector
Line-Out
MIC-IN
Line-In
3
r
r
r
K.B&USB Power on
Jumper (JP1)
Parallel Heade
PS/2 Mouse Keyboard
COM/VGA
Connector
RJ45 LAN
Over USB Port
USB 2.0 Port
USB 2.0 Port
Audio Connecto
Daughter Board
Expansion Connector
Front Panel Audio
SYSFAN1
Realtek
RTL8111C LAN
COM
Header
ALC 662
Audio Codec
ATX Powe
Connector
CPUFAN1
USB2.0 Header
(USB2, USB3)
8Mbit SPI Flash ROM BIOS
Intel CPU
Intel 945GC Chipset
Intel 82801G
ICH Chipset
DDRII
DIMM
ATA100
IDE Connector
Floppy Disk
Drive Connector
SATA
Connector
CD Audio In
32-bit PCI Slot
Clear CMOS (JBAT)
Speak Header.
USB Power on
Jumper (JP3)
PWR LED
Header
Front Panel
Connector
4
Jumper
Jumper Name Description Page
JP1
JP3
KB/USB Power On Function Setting 3-pin Block P.6
USB Power On Function Setting 3-pin Block P.6
JBAT CMOS RAM Clear Function Setting 3-pin Block p.7
Connectors
Connector Name Description Page
USB1,USB2 USB Port Connector 4-pin Connector p.7
RJ-45 from UL1 RJ45 LAN Connector 8-pin Connector p.7
VGA VGA Port Connector D-sub15-pin Female p.7
COM1 Serial Port Connector 9-pin Block p.7
Line-Out/Line-In /MIC Line-Out/Line-In /MIC Audio Connector 3 Phone Jack p.7
SATA1,2 Serial ATA Connectors 7-pin Connector p.8
IDE1 IDE Connector 40-pin IDE Block p.8
FLOPPY Floppy Disk Connector 34-pin Block p.9
Headers
Header Name Description Page
AUDIO Front Panel SPEAKER, MIC header 9-pin Block p.9
CDIN CD Audio-In Header 4-pin Block p.9
USB2/USB3 USB2.0 Port Headers 9-pin Block p.10
SPEAK Speaker connector 4-pin Block p.10
PWRLED Power LED Headers 3-pin Block p.10
JW_FP
(PWR LED/ IDE LED/
/Power Button /Reset)
Front Panel Headers
(PWR LED/ IDE LED/ /Power Button
/Reset)
CPUFAN, SFAN1/2 FAN Speed Header s 3-pin Block P.12
PARALLEL Parallel Port Header 25-pin Block P.12
COM2 Serial Port Header 9-pin Block P.12
CN1/CN2 Daughter Board Expansion Headers 50-pin block p.13
9-pin Block P.11
5
Chapter 2
Jumper Setting, Connectors and Headers
2-1 Jumper Setting
(1) JP1
(2) JP3
KB/USB Power on Function Setting
JP1
1-2 K.B&USBPOWER-ON Disacled(default)
USB Power on Function Setting
JP3
1-2 USB POWER-ON Disacled(default)
13
13
1 3
JP1
2-3 K.B& USB POWER-ON Enabled
1 3
JP3
2-3 USB POWER-ON Enabled
6
(3) Clear CMOS (3-pin): JBAT
JBAT
1-2 closed Normal (Default)
CMOS RAM Clear Setting
2-2 Connectors and Headers
2-2-1 Connectors
(1) I/O Back Panel Connector
PS/2 Mouse
PS/2 Keyboard
1
3
COM
Connector
VGA
Connector
JBAT
2-3 closed Clear CMOS
R
J45 LAN
1
3
USB
Connectors
USB
Connector
Line-Out
MIC-IN
Line-In
7
(2) Serial ATA Connector (7-pin female): SATA1/SATA2
SATA1
SATA2
Serial-ATA2 Port Connector
(3)IDE Connector：IDE1
IDE1
Pin 1
8
(4) Floppy drive Connector (34-pin block): FLOPPY
FLOPPY
Pin 1
Floppy Drive Connector
2-2-2 Headers
(1) Line-Out, MIC-In Header (14 pin): AUDIO
This header connects to Front Panel Line-out, MIC-In connector with cable.
GND
KEY
PRESENCE
SENSE1-RETURN
SENSE2-RETUR
AUDIO
(2) CD Audio-In Headers (4-pin): CDIN
2
Pin 1
AUD-MIC-R
AUD-MIC-L
SENSE-SEND
AUD-Lineout2-L
AUD-Lineout2-R
Line-Out, MIC Headers
9
10
9
CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM
CD-Audio output connector.
CDIN
CD-R
GND
4 1
CD Audio-In Headers
CD-LGND
(3) USB Port Headers (9-pin): USB2, USB3
VCC
-DATA
Pin 1
VCC
USB Port Header
NC
GND
+DATA
GND
-DATA
+DATA
(4) Speaker connector: SPEAK
This 4-pin connector connects to the case-mounted speaker. See the figure below.
(5) Power LED: PWR LED
10
The Power LED is light on while the system power is on. Connect the Power LED
from the system case to this pin.
PWRLED
Pin 1
SPEAK
Pin 1
NC
GND
VCC5
SPEAK
(6) Front Panel Headers: JW_FP
JW FP
Power button
Power LED
Front Panel Headers
Reset button
HD-LED
(7) FAN Speed Headers (3-pin): CPUFAN, SYSFAN1, and SYSFAN2
These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan
manufacturer, the wire and plug may be different. The red wire should be positive, while the
11
black should be ground. Connect the fan’s plug to the board taking into consideration the
polarity of connector.
+12v
Fan
Fan
power
clock
GND
3
Fan Headers
1
(8) Parallel Port Header: PARALLEL
The onboard parallel port header is a 25-pin connector for connecting devices such as
old-fashioned printer.
Pin 1
PARALLEL Connector
(9) Serial Port Connector (9-pin female): COM2
COM2 is a 9-pin RS232 D-Subminiature serial port connector.
12
DCD
RXD
TXD
DTR
GND
Pin1 Pin6
DSR
RTS
GTS
RI
Serial COM Port 9-pin Block
(10)Expansion Daughter Board Headers: CN1/CN2
Press Down Directly
To install a daughter board into CN1, CN2 is very easy, user just press down the daughter board directly into
these two connectors, in the direction shown as the above picture.
13
Chapter 3
Introducing BIOS
The BIOS is a program located on a Flash Memory on the motherboard. This program is a
bridge between motherboard and operating system. When you start the computer, the BIOS
program will gain control. The BIOS first operates an auto-d i agnostic test called POST (power
on self test) for all the necessary hardware, it detects the entire hardware device and
configures the parameters of the hardware synchronization. Only when these tasks are
completed done it gives up control of the computer to operating system (OS). Since the
BIOS is the only channel for hardware and software to communicate, it is the key factor for
system stability, and in ensuring that your system performance as its best.
In the BIOS Setup main menu of Figure 3-1, you can see several options. We will explain
these options step by step in the following pages of this chapter, but let us first see a short
description of the function keys you may use here:
• Press <Esc> to quit the BIOS Setup.
• Press ↑↓←→ (up, down, left, right) to choose, in the main menu, the option you want to
confirm or to modify.
• Press <F10> when you have completed the setup of BIOS parameters to save these
parameters and to exit the BIOS Setup menu.
• Press Page Up/Page Down or +/– keys when you want to modify the BIOS parameters for
the active option.
3-1 Entering Setup
Power on the computer and by pressing <Del> immediately allows you to enter Setup.
14
If the message disappears before your respond and you still wish to enter Setup, restart the
system to try again by turning it OFF then ON or pressing the “RESET” button on the system
case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If
you do not press the keys at the correct time and the system does not boot, an error message
will be displayed and you will again be asked to
Press <F1> to continue, <Del> to enter Setup
3-2 Getting Help
Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of the
screen.
Status Page Setup Menu/Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the
possible selections for the highlighted item. To exit the Help Window, press <Esc>.
3-3 The Main Menu
Once you enter Award® BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear
on the screen. The Main Menu allows you to select from 12 setup functions and 2 exit
choices. Use arrow keys to select among the items and press <Enter> to accept or enter the
sub-menu.
15
Phoenix – AwardBIOS CMOS Setup Utility
Standard CMOS Features
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configuration
PC Health Status
Esc : Quit
F10 : Save & Exit Setup
Figure 3-1
Miscellaneous Control
Load optimized Defaults
Load Standard Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
↑↓→←
: Select Item
Standard CMOS Features
Use this Menu for basic system configurations.
Advanced BIOS Features
Use this menu to set the Advanced Features available on your system.
Advanced Chipset Features
Use this menu to change the values in the chipset registers and optimize your system’s
performance.
Integrated Peripherals
Use this menu to specify your settings for integrated peripherals.
Power Management Setup
Use this menu to specify your settings for power management.
PnP/PCI Configuration
Use this menu to specify your settings for PnP/PCI Configuration.
PC Health Status
This entry shows your PC health status.
16
Miscellaneous Control
Use this menu to specify your settings for Miscellaneous Control.
Load Optimized Defaults
Use this menu to load the BIOS default values that are factory settings for optimal
performances system operations.
Load Standard Defaults
Use this menu to load the BIOS default values for the minimal/stable performance system
operation.
Set Supervisor Password
Use this menu to set supervisor password.
Set User Password
Use this menu to set user password.
Save & Exit Setup
Save CMOS value changes to CMOS and exit setup.
Exit Without Saving
Abandon all CMOS value changes and exit setup.
3-4 Standard CMOS Features
The items in Standard CMOS Setup Menu are divided into several categories. Each
category includes no, one or more than one setup items. Use the arrow keys to highlight the
item and then use the <PgUp> or <PgDn> keys to select the value you want in each item.
17
Phoenix – AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy) Wed, Aug13, 2008
Time (hh:mm:ss) 16 : 48 : 35
> SATA Port1 Master None
> SATA Port1 Master None
> IDE Channel 1 Master WDC WD800BB-00JHC0
> IDE Channel 1 Slave None
Drive A 1.44M, 3.5 in.
Video EGA/VGA
Halt On All Errors
Base Memory 639k
Extended Memory 1039360k
Total Memory 1040384k
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
↑↓→←
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Menu Level >
Change the day, month,
year and century
Item Help
Date
The date format is <day><month><date><year>.
Day of the week is from Sun to Sat, determined by BIOS. Read-only.
Day
Month
Date
Year
The month is from Jan. through Dec.
The date from 1 to 31 can be keyed by numeric function keys.
The year depends on the year of the BIOS.
Time
The time format is <hour><minute><second>.
SATA Port 1/SATA Port 2 /IDE Channel 1 Master/Slave
Press Enter and then PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that
the specifications of your drive must match with the drive table. The hard disk will not work
properly if you enter improper information for this category. If the type of hard disk drives
is not matched or listed, you can use Manual to define your own drive type manually.
If you select Manual, related information is asked to be entered to the following items. Enter
the information directly from the keyboard. This information should be provided in the
documentation from your hard disk vendor or the system manufacturer.
18
If the controller of HDD interface is SCSI, the selection shall be “None”.
If the controller of HDD interface is CD-ROM, the selection shall be “None”
Access Mode
Cylinder
Head
Precomp
Landing Zone
Sector
number of sectors
The settings are CHS, LBA, Large and Auto.
number of cylinders
number of heads
write precomp
landing zone
3-5 Advanced BIOS Features
Phoenix – AwardBIOS CMOS Setup Utility
Advanced BIOS Features
Virus Warning Disabled
CPU L3 Cache Enabled
CPU Feature Press Enter
Hard Disk Boot Priority Press Enter
Hyper-Threading Technology Enabled
Quick Power On Self Test Enabled
First Boot Device Floppy
Second Boot Device Hard Disk
Third Boot Device CDROM
Boot Other Device Enabled
Boot Up Floppy Seek Disabled
Boot Up NumLock Status On
Typematic Rate Setting Disabled
Typematic Rate (Chars/Sec) 6
Typematic Delay (Msec) 250
Security Option Setup
APIC Mode Enabled
MPS Version Control For OS 1.4
OS Select For DRAM > 64MB Non-OS2
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
↑↓→←
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Item Help
Menu Level >
19
Hard Disk Boot Priority
The selection is for you to choose the hard disk drives priorities to boot from.
Virus Warning
The selection allows you to choose the VIRUS Warning feature for IDE Hard Disk booting
sector protection. If this function is enabled and someone attempt to write data into this area,
BIOS will show a warning message on screen and alarm beep.
Disabled
(default) No warning message to appear when anything attempts to access the
boot sector or hard disk partition table.
Enabled
Activates automatically when the system boots up causing a warning
message to appear when anything attempts to access the boot sector
of hard disk partition table.
Quick Power On Self-Test
This category speeds up Power On Self Test (POST) after you power on the computer. If
this is set to Enabled, BIOS will shorten or skip some check items during POST.
Enabled
Disabled
(default) Enable quick POST
Normal POST
First/Second/Third Boot Device/Boot Other Device
The BIOS attempts to load the operating system from the devices in the sequence selected in
these items. The settings are Floppy, LS120, Hard disk, CDROM, ZIP100,USB-FDD,
USB-ZIP, USB-COROM, Legacy LAN and Disabled.
Boot Up Floppy Seek
During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks.
360K type is 40 tracks while 760K, 1.2M and 1.44M are all 80 tracks.
Boot Up NumLock Status
The default value is On.
On
(default)
Keypad is numeric keys.
20
Off
Keypad is arrow keys.
Typematic Rate Setting
Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the
typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled.
Typematic Rate (Chars/Sec)
Set the number of times a second to repeat a keystroke when you hold the key down. The
settings are: 6, 8, 10, 12, 15, 20, 24, and 30.
Typematic Delay (Msec)
Sets the delay time after the key is held down before is begins to repeat the keystroke. The
settings are 250, 500, 750, and 1000.
Security Option
This category allows you to limit access to the system and Setup, or just to Setup.
System
The system will not boot and access to Setup will be denied if the
correct password is not entered at the prompt.
Setup
(default) The system will boot, but access to Setup will be denied if the correct
password is not entered prompt.
MPS Version Control For OS 1.4
This option is only valid for multiprocessor motherboards as it specifies the version of the
Multiprocessor Specification (MPS) that the motherboard will use. The optional settings are:
1.1 and 1.4.
OS Select For DRAM > 64MB
Allows OS2® to be used with >64MB or DRAM. Settings are Non-OS/2 (default) and OS2.
Set to OS/2 if using more than 64MB and running OS/2®.
3-6 Advanced Chipset Features
The Advanced Chipset Features Setup option is used to change the values of the chipset
registers. These registers control most of the system options in the computer.
21
Phoenix – AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Timing Selectable By SPD
* SDRAM CAS Latency Time Auto
* SDRAM Cycle Time Auto
* SDRAM RAS# to CAS# Delay Auto
* SDRAM RAS# Precharge Time Auto
System BIOS Cacheable Disabled
Video BIOS Cacheable Disabled
Memory Hole at 15-16M Disabled
** VGA Setting**
Onchip Frame Buffer Size 8MB
DVMT Mold DVMT
DVMT/FIXED Memory Size 128MB
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
↑↓→←
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Menu Level >
Item Help
SDRAM CAS Latency Time
When synchronous DRAM is installed, the number of clock cycles of CAS latency depends
on the DRAM timing. The settings are: Auto, 3, 4 and 5.
SDRAM RAS-to-CAS Delay
This field let’s you insert a timing delay between the CAS and RAS strobe signals, used when
DRAM is written to, read from, or refreshed. Fast gives faster performance; and Slow gives
more stable performance. This field applies only when synchronous DRAM is installed in
the system.
SDRAM Ras Precharge Time
If an insufficient number of cycles is allowed for the RAS to accumulate its charge before
DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast
gives faster performance; and Slow gives more stable performance. This field applies only
when synchronous DRAM is installed in the system.
System BIOS Cacheable
22
Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in
better system performance. However, if any program writes to this memory area, a system
error may result. The settings are: Enabled and Disabled.
Onchip Frame Buffer Size
Use this item to set onchip frame buffer size. The optional settings are: 1MB and 8MB.
DVMT Mold
The optional settings are: FIXED, DVMT and BOTH.
DVMT/FIXED Memory Size
The optional settings are: 64MB, 128MB and 224 MB.
3-7 Integrated Peripherals
Phoenix – AwardBIOS CMOS Setup Utility
Integrated Peripherals
> Onboard IDE Function Press Enter
> Onboard Device Function Press Enter
> Onboard Super IO Function Press Enter
PWR status after PWR Failure Always Off
Init Display First PCI Slot
Menu Level >
Item Help
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
↑↓→←
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Onboard IDE Function
Please refer to section 3-7-1
Onboard Device Function
Please refer to section 3-7-2
Onboard Super IO Function
Please refer to section 3-7-3
PWR Status after PWR Failure
The settings are: Former Status; Always On; Always Off.
23
Init Display First
This item allows you to decide to whether activate PCI Slot or Onchip VGA first. The
settings are: PCI Slot, Onchip VGA.
3-7-1 Onboard IDE Function
Phoenix – AwardBIOS CMOS Setup Utility
Onboard IDE Function
OnChip IDE Channel Enabled
IDE Channel Master PIO Auto
IDE Channel Slave PIO Auto
IDE Channel Master UDMA Auto
IDE Channel Slave UDMA Auto
IDE DMA Transfer Access Enabled
IDE HDD Block Mode Enabled
*SATA Port Speed Settings Disabled
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
↑↓→←
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Menu Level >>
IDE DMA transfer access
The integrated peripheral controller contains an IDE interface with support for one IDE channels.
Select Enabled to activate each channel separately. The settings are: Enabled and Disabled.
IDE Channel Master/Slave PIO
The two IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-2) for each of the two
IDE devices that the onboard IDE interface supports. Modes 0 through 2 provide successively
increased performance. In Auto mode, the system automatically determines the best mode for each
device. The settings are: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode 4.
IDE Channel Master/Slave UDMA
Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the
operating environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus
master driver). If your hard drive and your system software both support Ultra DMA/33 and
Ultra DMA/66, select Auto to enable BIOS support. The settings are: Auto, Disabled.
IDE HDD Block Mode
Item Help
24
Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your
IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of
the optimal number of block read/writes per sector the drive can support. The settings are: Enabled,
Disabled.
SATA Port Speed Settings
The optional settings are: Disabled, Force GEN1 and Force GEN2.
3-7-2 Onboard Device Function
Phoenix – AwardBIOS CMOS Setup Utility
Onboard Device Function
Onboard PCIE LAN Controller Enabled
Onboard PCIE LAN BootROM Disabled
High Definition Audio Enabled
USB Host Controller Enabled
USB 2.0 Function Enabled
USB Keyboard Legacy Support Disabled
USB Mouse Legacy Support Disabled
USB Storage Legacy Support Disabled
**USB Mass Storage Device Boot Setting**
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
↑↓→←
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Menu Level >>
Item Help
Onboard PCIE LAN Controller
Setting to [Enabled] allows the BIOS to auto-detect the LAN controller and enable it. Setting
options:[ Enabled] and [Disabled] .
High Definition Audio
The selection for you to choose the embedded Audio function or 3rd party audio interface
installed. The settings are: Enabled and Disabled.
USB 2.0 Function Keyboard/Mouse /Storage Latency Support
Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have
a USB Mouse /keyboard. The settings are: Enabled, Disabled.
25
3-7-3 Onboard Super IO Function
Phoenix – AwardBIOS CMOS Setup Utility
Onboard Super IO Function
Onboard FDD Controller Enabled
Onboard Serial Port1 3F8/IRQ4
Onboard Serial Port2 2F8/IRQ3
UART2 Mode Select Normal
* IR Duplex Mode Half
Onboard Parallel Port 378/IRQ7
Parallel Port Mode SPP
*ECP Mold Use DMA 3
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
↑↓→←
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Menu Level >>
Onboard FDD Controller
Select Enabled if your system has a floppy disk controller (FDD) installed on the system board
and you wish to use it. If you install add-on FDC or the system has no floppy drive, select
Disabled in this field. The settings are: Enabled and Disabled.
Onboard Serial Port 1
The optional settings are：Disabled, 3F8/IRQ4，2F8/IRQ3, 3E8/IRQ4，2E8/IRQ3, 4E0/IRQ4,
4E8/IRQ3 and Auto.
Onboard Serial Port 2
The optional settings are：Disabled, 3F8/IRQ4，2F8/IRQ3, 3E8/IRQ4，2E8/IRQ3, 4E0/IRQ4,
4E8/IRQ3 and Auto.
UART2 Mode Select
This item allows you to determine which InfraRed(IR) function of the onboard I/O chip. The
optional settings are Normal and IrDA.
IrDA Duplex Mode
This field is available when UART Mode is set to either ASKIR or IrDA. This item enables you
to determine the infrared function of the onboard infrared chip. The options are Full and Half
Item Help
26
(default). Full-duplex means that you can transmit and send information simultaneously.
Half-duplex is the transmission of data in both directions , but only one direction at a time.
Onboard Parallel Port
The optional settings are: Disabled, 378/IRQ7, 278/IRQ5 AND 3BC/IRQ7.
Parallel Port Mode
SPP : Standard Parallel Port
EPP : Enhanced Parallel Port
ECP : Enhanced Com Port
SPP/EPP/ECP/ECP+EPP
To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate
the onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”,
the onboard parallel port will operate in ECP mode only. Choosing “ECP+EPP” will allow the
onboard parallel port to support both the ECP and EPP modes simultaneously. The ECP mode
has to use the DMA channel, so choose the onboard parallel port with the ECP feature. After
selecting it, the following message will appear: “ECP Mode Use DMA” at this time, the user can
choose between DMA channels 3 to 1. The onboard parallel port is EPP Spec. compliant, so
after the user chooses the onboard parallel port with the EPP function, the following message will
be displayed on the screen: “EPP Mode Select.” At this time either EPP 1.7 spec. or EPP 1.9
spec. can be chosen.
3-8 Power Management Setup
The Power Management Setup allows you to configure your system to most effectively save
energy saving while operating in a manner consistent with your own style of computer use.
27
Phoenix – AwardBIOS CMOS Setup Utility
Power Management Setup
ACPI Function Enabled
ACPI Suspend Type S1(DOS)
Power Management User Define
Video off Method V/H SYNC+Blank
Video Off In Suspend Yes
Suspend Type Stop Grant
MODEM Use IRQ 3
Suspend Mode Disabled
HDD Power Down Disabled
Soft-off by PWR-BTTN Instant-off
Wake-Up by PCI card Disabled
Power On by Ring Disabled
Wake-up by USB KB from S3(S4) Disabled
PS2 KB/MS Wake-up from S4-S5 Disabled
Resume by Alarm Disabled
X Date (of Month)Alarm 0
X Time (hh:mm:ss)Alarm 0 : 0 :0
PM Timer Reload Event Press Enter
Menu Level >
Item Help
PCI Express PM Reload Function Press Enter
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
↑↓→←
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
ACPI Function
This item allows you to Enabled/Disabled the Advanced Configuration and Power Management
(ACPI). The settings are Enabled and Disabled.
Video Off Method
This determines the manner in which the monitor is blanked.
DPMS
Blank Screen
V/H SYNC+Blank
(default) Initial display power management signaling.
This option only writes blanks to the video buffer.
This selection will cause the system to turn off the vertical and
horizontal synchronization ports and write blanks to the video buffer.
Suspend Type
The settings are: Stop and PWR On Suspend.
MODEM Use IRQ
28
If you want an incoming call on a modem to automatically resume the system from a
power-saving mode, use this item to specify the interrupt request line (IRQ) that is used by the
modem. You might have to connect the fax/modem to the motherboard Wake On Modem
connector for this feature to work.
Soft-Off by PWRBTN
Under ACPI (Advanced Configuration and Power management Interface) you can create a
software power down. In a software power down, the system can be resumed by Wake up
Alarms. This item lets you install a software power down that is controlled by the power
Button on your system. If the item is set to Instant-Off, then the power button causes a
software power down. If the item is set to Delay 4 Sec, then you have to hold the power
button down for four seconds to cause a software power down. The settings are: Delay 4 Sec,
Instant-Off.
Power On by Ring
During Disabled, the system will ignore any incoming call from the modem. During Enabled,
the system will boot up if there’s an incoming call from the modem.
Resume by Alarm
This function is for setting date and time for your computer to boot up. During Disabled,
you cannot use this function. During Enabled, choose the Date and Time Alarm:
Date(of month) Alarm
You can choose which month the system will boot up. Set to 0, to boot every day.
Time(hh:mm:ss) Alarm
You can choose what hour, minute and second the system will boot up.
Note: If you have change the setting, you must let the system boot up until it goes to the
operating system, before this function will work.
PM Timer Reload Event
In this item users can either select Enabled or Disabled to enable or disable Primary IDE 0;
Primary IDE 1;Secondary IDE 0; Secondary IDE 1; FDD, COM, LPT Port or PCI
PIRQ(A-D).
PCI Express PME Function
Press Enter to either set Enabled or Disabled the PCI Express PM Function.
29
3-9 PnP/PCI Configuration
Phoenix – AwardBIOS CMOS Setup Utility
PnP/PCI Configuration
IRQ Resources Press Enter
PCI/ VGA Palette Snoop Disabled
**********PCI Express Relative Items*********
Maximum Payload Size 128
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
↑↓→←
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Menu Level >
PCI/VGA Palette Snoop
This item is designed to overcome problems that can be caused by some non-standard VGA
cards. This board includes a built-in VGA system that does not require palette snooping so
you must leave this item disabled.
IRQ Resources
Names the interrupt request (IRQ) line assigned to the USB on your system. Activity of the
selected IRQ always awakens the system.
Item Help
3-10 PC Health Status
This section shows the Status of you CPU, Fan, and Warning for overall system status. This
is only available if there is Hardware Monitor onboard.
30
Phoenix – AwardBIOS CMOS Setup Utility
PC Health Status
Shutdown Temperature Disabled
CPU Thermal-Throttling Disabled
* CPU Thermal-Throttling Temp 70°C
* CPU Thermal-Throttling Duty 50.00%
* CPU Thermal-Throttling Beep Enabled
Show PC Health in POST Enabled
> Smart FAN Configurations Press Enter
VCC3v 3.31V
Vcore 1.28V
NB 1.26V
+5V 5.12V
+12V 11.88V
5VSB 5.00V
VDIMM 1.87V
VSB3V 3.37V
Vbat 3.28V
CPU Temperature 64°C147°F
System Temperature 38°C/96°F
CPUFAN Speed 2912RPM
SYSFAN1 Speed 5836 RPM
SYSFAN2 Speed 0 RPM
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
↑↓→←
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Menu Level >
Item Help
Shutdown Temperature
This item can let users setting the Shutdown temperature, when CPU temperature over this
setting the system will auto shutdown to protect CPU.
Show PC Health in Post
During Enabled, it displays information list below. The choice is either Enabled or Disabled
CPU Temperature/ System Temperature/CPU FAN Speed, SYS FAN1, SYSFAN2
Speed/VCC 3V/Vcore/ NB/+5V/+12V/5VSB(V)/VDIMM/VSB3V/Vbat
This will show the CPU/FAN/System voltage chart and FAN Speed.
31
3-11 Miscellaneous Control
Phoenix – AwardBIOS CMOS Setup Utility
Miscellaneous Control
Auto Detect PCI Clock Disabled
Spread Spectrum Disabled
** Current Host/PCI Clock is 133/33MHZ**
Host/PCI Clock at Next Boot is 133/33MHZ
** Current DRAM CLOCK 533 MHz **
DRAM Clock at Next Boot By SPD(DDR533MHz)
VDIMM Select 1.85V(Default)
VCC NB Select 1.53v(Default)
GMCH VCCP Select 1.12v(Default)
VDA C25 Select 2.50v(Default)
Move Enter:Select Item +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
↑↓→←
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Auto Detect PCI Clock
This item allows you to enable/disable auto detect PCI Clock.
The settings are: Enabled, Disabled.
Spread Spectrum
This item allows you to set the Spread Spectrum as Enable or Disabled.
Host/PCI Clock at Next Boot
This item allows you to select the CPU/PCI Clock.
DRAM Clock at Next Boot
This item allows you to set DRAM clock.
VDIMM Select
This item allows you to set the voltage of DRAM DIMM. The optional settings are: 1.85v
(Default), 1.95v, 2.05v and 2.15v.
VCC NB Select
This item allows you to set Northbridge voltage. The optional settings are from 1.41v to
1.99v.
Item Help
Menu Level >
32
GMCH VCCP Select
The optional settings are from 1.04v to 1.46v.
VDAC25 Select
The optional settings are from 2.31v to 3.25v.
3-12 Password Setting
You can set either supervisor or user password, or both of them. The differences are:
Supervisor password: Can enter and change the options of the setup menus.
User password: Can only enter but do not have the right to change the options of the
setup menus. When you select this function, the following message
will appear at the center of the screen to assist you in creating a
password.
ENTER PASSWORD:
Type the password, up to eight characters in length, and press <Enter>. The password typed now
will clear any previously entered password from CMOS memory. You will be asked to confirm
the password. Type the password again and press <Enter>. You may also press <Esc> to abort
the selection and not enter a password.
To disable a password, just press <Enter> when you are prompted to enter the password. A
message will confirm that the password will be disabled. Once the password is disabled, the
system will boot and you can enter Setup freely.
PASSWORD DISABLED.
When a password has been enabled, you will be prompted to enter it every time you try to enter
Setup. This prevents an unauthorized person from changing any part of your system
configuration.
Additionally, when a password is enabled, you can also require the BIOS to request a password
every time your system is rebooted. This would prevent unauthorized use of your computer.
You determine when the password is required within the BIOS Features Setup Menu and its
Security option. If the Security option is set to “System”, the password will be required both at
boot and at entry to Setup. If set to “Setup”, prompting only occurs when trying to enter Setup.
33
3-13 Load Standard/Optimized Defaults
Load Standard Defaults
When you press <Enter> on this item, you get confirmation dialog box with a message similar
to:
Load Standard Defaults (Y/N)? N
Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system
operations.
Load Optimized Defaults
When you press <Enter> on this item, you get a confirmation dialog box with a message
similar to:
Load Optimized Defaults (Y/N)? N
Pressing <Y> loads the default values that are factory settings for optimal performance
system operations.
34
Loading...